This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SEATTLE
SPOKANE
WASHINGTON STATE
REDMOND
SITE DATA TABLE (ref. RZC 21.08.060B)
AVERAGE LOT SIZE 7000 SF 103,849 SF
DENSITY 80% OF NET ACRES N/A - EXISTING LOT
LOT WIDTH CIRCLE 40 FEET 40'-0"
FRONT SETBACK 15 FEET 15'-0"
GARAGE SETBACK 18 FEET N/A - NO GARAGE
SIDE/INTERIOR SETBACK 5 FEET/10 FEET 5'-0"
REAR SETBACK 10 FEET 10'-0"
BUILDING SEPARATION 10 FEET 16'-10 1/4"
OPEN SPACE 20% OF TOTAL LOT AREA (20,770 SF)
93% (96,614 SF)
MAXIMUM REQUIRED PROVIDED
LOT COVERAGE FOR STRUCTURES
35% OF TOTAL LOT AREA 7% (7235 SF)
IMPERVIOUS SURFACE 60% OF TOTAL LOT AREA 26.9%
BUILDING HEIGHT 35 FEET 15 FEET (NEW ADDITION)21 FEET (EXISTING)
LOT FRONTAGE 20 FEET 164'-11"
MINIMUM REQUIRED PROVIDED
YES
YES
YES
N/A - NO GARAGE
YES
YES
YES
YES
MEETS REQ'S
YES
YES
YES
YES
MEETS REQ'S
N/A - EXISTING LOT
BUILDING DATA TABLE
N/A N/A ADDITION AND REMODEL
E OCCUPANCY(EDUCATION)
E OCCUPANCY R OCCUPANCY(RESIDENTIAL)
N/A - NO CHANGE
N/A - NO CHANGE N/A - NO CHANGE 610 SF
3300 SF 360 SF 3000 SF
BUILDING A BUILDING B BUILDING C
SCOPE OF WORK
EXISTING OCCUPANCY
NEW OCCUPANCY
ADDITION SF
EXISTING SF
N/A - NO CHANGE E OCCUPANCY
CAMPUS
610 SF
6600 SF
TOTAL SF 3300 SF - NO CHANGE 360 SF - NO CHANGE 3610 SF 7270 SF
BASIS OF BEARINGS: WASHINGTON STATE PLANE NORTH, NAD 1983 (91-HARN) PER CITY OF REDMOND (COR)CITY OF REDMOND CONTROL POINT DESIGNATION GPS90-3G2 , BEING A 3" BRASS DISC WITH PUNCH DOWN 1.67', AT INTERSECTION OF NORTHEAST 40TH STREET & 156TH AVENUE NORTHEAST WAS HELD FOR POSITION AND A LINE BETWEEN SAID POINT GPS90-3G2 AND CITY OF REDMOND POINT DESIGNATION NO. GLO-4GSW, BEING A 3" BRASS DISC WITH PUNCHDOWN 0.72', 15'± EAST OF INTERSECTION OF NORTHEAST 40TH STREET & 164TH AVENUE NORTHEAST WAS HELD FOR ROTATION. BEARING BETWEEN THESE MONUMENTS WAS TAKEN AS SOUTH 89°10'27" EAST.
VERTICAL DATUM IS NAVD88 PER CITY OF REDMONDPUBLISHED BENCHMARKVERTICAL DATUM FOR THIS SURVEY IS ESTABLISHED PER THE PUBLISHED ELEVATION OF CITY OF REDMOND POINT DESIGNATION COR 9117, BEING A 3" BRASS DISC IN MONUMENT CASE 4.4' SOUTH OF THE SOUTH EDGE OF CONCRETE SIDEWALK ON NORTHEAST 40TH STREET, 30'± WEST OF THE CENTERLINE OF 162ND AVENUE NORTHEAST STAMPED "CITY OF REDMOND BM 66". ELEVATION WAS HELD AT 309.52'
CHECK BETWEEN PROJECT BENCHMARK AND CITY OF REDMOND POINT DESIGNATION COR9118, BEING A 2" BRASS DISC AT THE NORTHWEST CORNER OF A CONCRETE PAD FOR TRAFFIC CONTROL RISERS AT THE SOUTHEAST QUADRANT OF BELLEVUE-REDNOND ROAD AND NORTHEAST 40TH STREET, RESULTED IN A VERTICAL CLOSURE OF 0.155' OF PUBLISHED.
NOTE: STORMWATER CAPITAL FACILITIES CHARGE FEE IS APPLICABLE AT PERMIT ISSUANCE.
NOTE: A SPRINKLER SYSTEM WITH QUICK-RESPONSE HEADS WILL BE INSTALLED IN ACCORDANCE WITH IBC CHAPTER 9 AND NFPA-13. SPRINKLER DRAWINGS TO BE SUBMITTED BY LICENSED INSTALLER AS DEFERRED SUBMITTAL AFTER PROJECT BIDS.
OWNER
CASCADIA SCHOOL4239 162ND AVE NEREDMOND, WA 98052425.881.2825PHILIP KEETON
ARCHITECT
NAC|ARCHITECTURE2025 1ST AVE SUITE 300SEATTLE, WA 98121206.441.4522KEVIN FLANAGAN
CIVIL ENGINEER
JACOBSON ENGINEERING255 S KING ST SUITE 800SEATTLE, WA 98104206.399.6233ALAN JACOBSON
ARBORIST
DAVEY RESOURCE GROUP INC.18809 10TH AVE NESHORELINE, WA 98155206.714.3147IAN SCOTT
STRUCTURAL ENGINEER
SWENSON SAY FAGET2124 3RD AVE SUITE 100SEATTLE, WA 98121206.443.6212GREGORY JUTTNER
ELECTRICAL ENGINEER
NAC ENGINEERING2025 1ST AVE SUITE 300SEATTLE, WA 98121206.441.4522MARK MCMICHAEL
DW
WH
T
OV
EN
DW
WH
WH
OVEN
CLASSROOM
102
WORK ROOM
103
STORAGE
103A
LOBBY
101
CLASSROOM
107
TOILET
106
TOILET
105
TOILET
104
CLASSROOM
108
20'-3
241/2
56"
21'-7 1/8" 8'-0"
2'-6
"1
0'-4 1
/8"
29'-7 1/8"
FIRE RISER
109
A4.01
2
A4.011
A4.013
A7.021D
1A
1B
1C
A7.02
4C
4B
4A
4D
A7.02
3A
3E 3C
3D
A7.02
3B
A7.02 2A2C
2B
1E
A7.031
25
3
A7.03
4
A7.02 2D2E
4'-9
1/2
"
19'-3
"
2
A4.04
1
A4.04
3
A4.04
4
A4.04
A7.0114
2E
2F
2G
A7.01
2A
2D
2C
A7.01 1F
1E
18
1G
A7.01
1B
1A
1C
1D
A7.01
3C
3D
3B
3A
2B
CLASSROOM
110
TOILET
110A
LOUVERED DOORS
A7.01
A
A7.01
B
4'-2 1/4"
9'-2 3/8"
5'-7 1/2"
7'-6"
6'-9
"
19'-8 3/16"
24'-0
1/2
"
1'-1
0 1
1/1
6"
21S
B
21 B
S 20A
R
20A
R
1A
20 AR
2A
2A
A
2 AA
1A
20RA
20R
A
21BS
2A
A
21B
S
1AA
20R
A
1A
A1
A
A
1AA
1A
A
1AA
1A
A
2AA
2A
A1
A
A
1AA
1AA
1A
A
1A
A
110
110A
101
108
109
107
102A
107A
104
105
106
102
ELEC
102A
STOR
107A
A4.01
7
A4.01 6
A4.01
4
A4.01 5
5'-0 3/8"3'-3"
12
2
7
5
2
6
8
4
3
1. SEE MAIN FLOOR PLAN FOR DIMENSIONS AND WALL TYPE REFERENCES.
2. SEE DOOR AND RELITE SCHEDULES, SHEET A3.04 FOR DOOR HARDWARE AND OTHER FIRE RATING REQUIREMENTS FOR DOORS AND RELITES.
3. SEE ELECTRICAL FOR EXIT SIGNS AND EMERGENCY EGRESS LIGHT FIXTURES.
4. STORAGE AND USE OF CLASS I, II AND IIIA LIQUIDS ARE PROHIBITED EXCEPT IN APPROVED QUANTITIES AS NECESSARY IN CLASSROOMS FOR OPERATION AND MAINTENANCE. THE QUANTITIES OF OTHER HAZARDOUS MATERIALS SHALL BE AS APPROVED BY THE FIRE MARSHALL.
5. BUILDING IS COMBUSTIBLE FULLY SPRINKLERED CONSTRUCTION. AREAS OF EVACUATION ASSISTANCE ARE NOT REQUIRED. QUICK RESPONSE HEADS ARE USED WHERE ALLOWED BY IBC CHAPTER 9 AND A WRITTEN EVACUATION PLAN WILL BE SUBMITTED FOR APPROVAL PRIOR TO OCCUPANCY.
6. ARCHITECT SHALL REVIEW ALL DEFERRED SUBMITTALS AND VERIFY COMPLIANCE WITH THE DESIGN CONCEPT AND CODE REQUIREMENTS RELATING TO:A. AUTOMATIC SPRINKLER SYSTEM DESIGN DRAWINGS.B. MANUAL AND AUTOMATIC FIRE ALARM DRAWINGS.C. INSTALLATION DETAILS OF ACOUSTICAL CEILING SUSPENSION SYSTEM.D. INSTALLATION DETAILS OF MEMBRANE AND THROUGH-PENETRATION FIRE STOPS, AND FIRE-RESISTIVE
JOINT SYSTEMS.E. DESIGN DETAILS AND STRUCTURAL CALCULATIONS FOR THE SEISMIC ANCHORAGE AND BRACING OF
EACH PIECE OF FLOOR MOUNTED AND ROOF MOUNTED MECHANICAL AND OTHER EQUIPMENT WEIGHING 400 POUNDS OR MORE.
F. WRITTEN FIRE AND LIFE SAFETY EMERGENCY PLAN, WHICH SPECIFICALLY ADDRESSES THE EVACUATION OF PERSONS WITH DISABILITIES.
1. APPROVED AUDIBLE SPRINKLER FLOW ALARMS SHALL BE INSTALLED WITHIN THE BUILDING AND ON THE EXTERIOR IN APPROVED LOCATIONS; ACTUATION SHALL CONFORM TO IBC CHAPTER 9. ELECTRICAL VALVE MONITORING FOR SPRINKLER SYSTEM AND WATER FLOW SWITCHES SHALL BE INSTALLED AND CONNECTED TO AN APPROVED CENTRAL, REMOTE, OR PROPRIETARY MONITORING STATION.
2. AN APPROVED MANUAL AND AUTOMATIC FIRE ALARM SYSTEM SHALL BE INSTALLED AS SPECIFIED IN THE FIRE CODE; VISIBLE ALARMS COMPLYING WITH WSBC SECTION 1106.15.2 SHALL BE INSTALLED IN ALL COMMON-USE AREAS, ASSEMBLY AREAS, TOILET ROOMS, HALLWAYS, LOBBIES AND CORRIDORS.
3. INTERIOR WALL AND CEILING FINISHES SHALL CONFORM TO IBC SECTION 803 AND TABLE 803.11 FOR FLAME SPREAD REQUIREMENTS.
FLOOR PLAN GENERAL NOTES
1. THE DEMOLITION PLANS INCLUDE THE SCOPE OF DEMOLITION WORK REQUIRED PRIOR TO STARTING THE MODERNIZATION WORK, BUT ARE NOT INTENDED TO INCLUDE ALL OF THE DETAIL REQUIREMENTS. ALL DEMOLITION WORK NOT SHOWN ON DRAWINGS OR SPECIFIED WHICH IS REQUIRED FOR COMPLETION OF WORK INCLUDED IN THE CONTRACT DOCUMENTS SHALL BE THE RESPONSIBILITY OF THE GENERAL CONTRACTOR.
2. COORDINATE ALL DEMOLITION WORK WITH ALL TRADES AND REVIEW DRAWINGS FOR EXACT LOCATIONS OF ALL OPENINGS, ETC., PRIOR TO STARTING WORK.
3. ALL EXISTING WALLS, STRUCTURE, DOORS AND OTHER ITEMS TO REMAIN ARE SHOWN AS SOLID LINES OR INDICATED AS SUCH BY NOTE. ALL STRUCTURAL MEMBERS, SLABS AND ROOF STRUCTURE/DECKS ARE TO REMAIN UNLESS SPECIFICALLY NOTED OTHERWISE. ALL STRUCTURE, WALLS, DOORS, WINDOWS, CABINETRY, EQUIPMENT, FIXTURES, ETC., TO BE REMOVED ARE SHOWN DASHED OR NOTED AS SUCH. REMOVE ALL ACCESSORIES, EQUIPMENT, FIXTURES, FINISHES OTHER THAN PAINT, ETC. ... WHETHER SPECIFICALLY SHOWN OR NOT, UNLESS NOTED OTHERWISE.
4. SEE ELECTRICAL DRAWINGS FOR DESCRIPTION OF WORK UNDER THOSE SUBCONTRACTORS, INCLUDING UTILITIES AND FIXTURES (I.E., SINKS, TOILET FIXTURES, EXTERIOR LIGHT FIXTURES) SHOWN TO BE REMOVED ON THIS PLAN.
5. SEE SITE PLAN, ROOF PLAN, BUILDING ELEVATIONS, DETAILS AND STRUCTURAL DRAWINGS FOR ADDITIONAL DEMOLITION INFORMATION RELATING TO THOSE AREAS OF WORK AND NOT SPECIFICALLY NOTED HERE.
6. EXTERIOR WALLS TO BE REMOVED ARE GENERALLY WOOD FRAMED.
7. INTERIOR WALLS TO BE REMOVED ARE GENERALLY WOOD FRAMED UNLESS NOTED OTHERWISE.
8. ALL STRUCTURAL MEMBERS INCLUDING BEARING WALLS AFFECTED BY THIS DEMOLITION ARE TO BE VERIFIED AND ADEQUATELY SHORED BEFORE REMOVAL.
9. ALL EXISTING FINISH FLOORING IS TO BE REMOVED TO EXISTING SUBFLOOR, UNLESS NOTED OTHERWISE. ALL EXISTING FINISH FLOORING IS ASSUMED TO BE WOOD FLOORING UNLESS NOTED OTHERWISE. INFILL, PATCH AND REPAIR AS NECESSARY TO PREP FOR NEW FLOORING INCLUDING AT REMOVED WALLS.
10. DOORS SHOWN TO BE REMOVED INCLUDE DOORS, FRAMES, SIDELITES, TRANSOMS, CENTER POSTS, PIPE RAILS, HARDWARE, STOPS AND ADJACENT FURRING TO FULLY REVEAL ROUGH OPENING.
11. ALL MASONRY REMOVAL IS TO BE REMOVED BY SAWCUTTING. PATCH AND REPAIR EXPOSED WALLS DAMAGED BY REMOVAL OF WORK AND LEAVE IN NEAT, CLEAN, FINISHED CONDITION. PROVIDE NEW LINTEL TO SUPPORT CMU. SEE STRUCTURAL DRAWINGS FOR DETAILS.
12. NEW WALL OPENINGS IN EXISTING WALLS NOT DIMENSIONED ON THIS PLAN ARE SHOWN ON THE FLOOR PLANS. NEW OPENINGS IN EXISTING CONCRETE WALLS ARE TO BE SAWCUT.
13. PATCH AND REPAIR ALL DAMAGED AREAS AFFECTED BY THIS WORK.
14. MISC NEW WORK TRIGGERED BY DEMOLITION IS SHOWN HERE ON DEMOLITION PLANS.
15. REMOVE EXISTING FLOOR SLABS AS REQUIRED FOR NEW PAD & CONTINUOUS FOOTINGS. COORDINATE WITH STRUCTURAL DRAWINGS. PROVIDE NEW 4" CONC SLAB INFILL OVER VAPOR BARRIER AND SPEC'D SUBSTRATE GRAVEL AFTER COL/FOOTINGS ARE INSTALLED.
16. ALL VOIDS IN GRADE OR BELOW SLABS RESULTING FROM THIS WORK ARE TO BE FILLED WITH COMPACTED STRUCTURAL FILL OR CONTROLLED DENSITY FILL TO REQUIRED NEW ELEVATION PRIOR TO CONTINUING CONSTRUCTION.
17. REMOVAL OF EXISTING EXTERIOR WALLS INCLUDES REMOVAL OF ASSOCIATED FOUNDATION WALL & FOOTING, UNLESS NOTED OTHERWISE. SEE CODED NOTES AND STRUCTURAL DRAWINGS FOR FURTHER CLARIFICATION.
GENERAL DEMOLITION NOTES
DEMOLITION PLAN LEGEND
FRAMED WALL TO BE REMOVED
EXISTING WALL TO REMAIN
EXISTING DOOR AND FRAME TO BE REMOVED
EXISTING WINDOW AND FRAME TO BE REMOVED
REMOVE DOOR, FRAME AND ALL ASSOCIATED HARDWARE TO LEAVE CLEAN OPENING FOR INFILL
REMOVE PLUMBING FIXTURES, CABINETRY AND BATHROOM ACCESSORIES
REMOVE PLUMBING FIXTURES, CABINETRY AND KITCHEN ACCESSORIES
REMOVE GARAGE DOOR AND ACCESSORIES
REMOVE WATER HEATER
REMOVE FURNACE
REMOVE STOVE, HEARTH AND ACCESSORIES
REMOVE CENTRAL VACUUM AND ACCESSORIES, CAP CONNECTIONS
1. LOCATION AND SPACING OF WINDOW MULLIONS, MASONRY CONTROL JOINTS AND COURSE PATTERNS, ETC, ARE TO BE AS SHOWN ON EXTERIOR ELEVATIONS. WHERE NOT DIMENSIONED OR DETAILED, WINDOW MULLIONS AND MATERIAL JOINTS ARE TO BE EQUALLY SPACED AND/ OR CENTERED/ ALIGNED W/ ADJACENT ELEMENT (MASONRY COLUMN, EDGE OR CENTER LINE OF WINDOW OR DOOR OPENING, ETC) AS SHOWN.
2. REFER TO DETAILS FOR DIMENSION REFERENCE POINTS.
3. CONTROL JOINTS EXTEND FULL HEIGHT OF MASONRY, TYP. WHERE "CJ" IS INDICATED AT INSIDE CORNERS THE JOINT SHALL PENETRATE THE MASONRY SURFACE ON WHICH THE LABEL OCCURS. SEE DETAILS FOR ADDITIONAL CJ LOCATIONS.
4. ALL WINDOW AND LOUVER DIMENSIONS ARE FOR ROUGH OR MASONRY OPENING, UNLESS NOTED OTHERWISE. SEE PLANS FOR ADDITIONAL DIMENSION INFORMATION.
5. 100'-0" IS THE DATUM ELEVATION AND CORRESPONDS TO THE REFERENCED FLOOR SLAB ELEVATION 275.80'. SEE CIVIL FOR FURTHER INFORMATION.
6. EXTERIOR WALL FINISHES EXTEND FULL HEIGHT TO SOFFITS (NOT SHOWN WHERE EAVES OBSCURE VIEW). SEE BUILDING SECTIONS & DETAILS.
7. SEE REFLECTED CEILING PLANS (RCP) FOR CEMENT FIBER BOARD CLAD SOFFIT COLORS. CEMENT FIBER BOARD CLAD FINS & VERT FACE OF SOFFIT TO MATCH COLOR OF ASSOCIATED SOFFIT AS NOTED ON RCP.
EXTERIOR ELEVATION GENERAL NOTES
CEMENT FIBER BOARD
COMPOSITION SHINGLE ROOFING
WOOD SIDING
NOTE: THIS LEGEND DOES NOT INCLUDE ALLMATERIALS. SEE NOTES & REFERENCED DETAILSFOR ADDITIONAL INFORMATION.
CLEAR GLASS
TEMPERED GLASS WHERE REQUIRED
MATERIALS LEGEND GLAZING LEGEND
T
1. EXTERIOR FINISH NOTES APPLY TO BUILDING AND SITE.
2. EXTERIOR STEEL DOORS AND FRAMES TO BE PT 6.X.
3. ALL METAL FASCIA AND CONTINOUS CLEATS TO BE PT 6.X (FACTORY FINISH).
4. EXTERIOR LOUVERS AND ASSOCIATED EXPOSED FLASHING COLOR TO MATCH SIDING.
5. ALL EXPOSED CAST IN PLACE CONCRETE TO HAVE A CLEAR SEALER PER SPECIFICATIONS.
6. ALL METAL FINS/ SOFFITS TO BE PT 6.X (FACTORY FINISH), UNLESS NOTED OTHERWISE.
7. BIKE RACKS TO BE GALVANIZED STEEL, NO PAINT.
8. SIGN POSTS, BOLLARDS, AND STEEL GATES TO BE PT 6.X.
9. ALL GUTTERS TO BE PT 6.X (FACTORY FINISH), ALL EXPOSED DOWNSPOUTS TO BE PT 6.X (FACTORY FINISH).
10. ROOF TOP VENTS, COWLS, FLUES AND ASSOCIATED FLASHINGS TO BE PT 6.X.
11. ALL FIBER CEMENT SOFFIT BOARD TO BE PT 6.X.
12. EXPOSED STEEL LINTELS SUPPORTING MASONRY TO BE PT 6.X.
Application LED bollard with unshielded symmetric light distribution. Designed for landscapes, pathways, and open spaces, these robust luminaires can delineate and structure exterior spaces. Provided with mounting system that allows the luminaire to be adjusted independent of anchor bolt orientation.
Materials Luminaire housing constructed of die-cast and extruded marine grade, copper free (≤ 0.3% copper content) A360.0 aluminum alloy White acrylic diffuser High temperature silicone gasket Mechanically captive stainless steel fasteners
NRTL listed to North American Standards, suitable for wet locations Protection class IP 65 Weight: 40.2 lbs
Electrical Operating voltage 120-277V AC Minimum start temperature -30° C LED module wattage 32.0 W System wattage 36.0 W Controllability 0-10V dimmable Color rendering index Ra > 80 Luminaire lumens 2838 lumens (3000K) Lifetime at Ta = 15° C 105,000 h (L70) Lifetime at Ta = 50° C 58,000 h (L70)
LED color temperature
4000K - Product number + K4 3500K - Product number + K35 3000K - Product number + K3 2700K - Product number + K27
BEGA can supply you with suitable LED replacement modules for up to 20 years after the purchase of LED luminaires - see website for details
Finish All BEGA standard finishes are matte, textured polyester powder coat with minimum 3 mil thickness.
Available colors Black (BLK) White (WHT) RAL: Bronze (BRZ) Silver (SLV) CUS:
Slot 4 LED Surface MountThe Slot LED family of luminaires offers an unparalleled package of performance and features for your next lighting project. Precision lumen DIRECTIR optics deliver optimized light where needed for ceilings and walls. With other key features such as simplified installation, seamless controls integration and superior LED color constancy, the Slot LED family from Mark Lighting offers exceptional quality and design flexibility.
Technical Drawing
Type:
Project:
Catalog Number:DO NOT TYPE HERE. Autopopulated field.
HousingNominal 3.5” x 3.75” extruded aluminum housing FinishWhite, Black or Silver powdercoat ReflectorFormed steel with high reflectance white.Distribution/ShieldingExtruded 90% transmissive acrylic lens with a textured surface providing diffuse illumination and a uniform appearance for direct lambertian distribution (No Optics). Wall Wash (WW) and Wall Graze (WG) distribution options incorporate co-extruded lenses. Shielding is available as an external blade louver for WW or WG options, or an internal blade louver in lieu of lambertian distribution diffuser.LED ComponentsLinear: Nichia®- 757 series LED chips (>80 CRI)ElectricalLong-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 80% LED lumen maintenance at 60,000 hours (L80/60,000).Color ConsistencyThe Acuity Brands circuit boards for the linear LED components use a precise binning algorithm which creates a consistent color temperature from board to board. The color a variation of no greater than a 2.5 Step MacAdam (2.5SDCM) along the black body locus from board to board.DrivereldoLED® driver provides natural dimming with smooth, continuous and flicker-free deep dimming. Supports operation between 120VAC and 277 VAC, with low inrush current (NEMA 410) and THD < 20%. Meets FCC Title 47 C.F.R. 15 Class A or Class B requirements. Lutron high performance driver options also available.Certification CSA tested to UL 1598 standards, assembled in the USA. Damp location listed.Listings DesignLights Consortium® (DLC) Premium qualified product. Not all versions of this product may be DLC Premium qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified.Warranty5-year limited warranty. Complete warranty terms located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspxNote: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. Specifications subject to change without notice.
Specification Features
Direct Surface
3 1/2
3 3/4
4FT INDIVIDUAL (35K) DIRECT
Lumens Output 400LMF 600LMF 800LMF 1000LMF
Delivered Lumens 1800 2707 3571 4103
Input Watts 15.4 23.4 32 37.3
Lumen/Watt 117 115 112 110
Fixture Performance
* Consult factory for customized lumen output and wattage between 350LMF and 1050LMF.
A+ Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning.
• All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency
• This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background*
• This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background*
To learn more about A+, visit www.acuitybrands.com/aplus.
_FT Specify continuous run length (in whole feet, 2' minimum)
Unit length may affect available options. 2’ & 3’ only available as individual units
For runs longer than 8FT: ALWAYS order the run by the TOTAL RUN LENGTH. Ordering the sections individually will not provide the correct joining hardware to allow connection in the field.
MSL4 4’
MSL5 5’
MSL6 6’
MSL7 7’
MSL8 8’
80CRI 80 CRI
90CRI 90 CRI
27K 2700K
30K 3000K
35K 3500K
40K 4000K
50K 5000K
400LMF 400 lumens per FT
600LMF 600 lumens per FT
800LMF 800 lumens per FT
1000LMF 1000 lumens per FT
_LMF 1 # lumens per FT
(blank) Standard lambertian distribution
WW 2 Wallwash distributions
WG Wall graze distribution
WW and WG not available with Downlights, EGLD, LVRR or LVRRA.
Downlight Downlight Shape Downlight Color Rendering Downlight Color Temp Minimum Dimming Level Switching Optional Shielding
(blank) No Downlight modules in fixture
2DL LED downlights (2 per unit)
_DL LED downlights per run (3DL, 4DL, etc.)
(blank) No downlight modules in fixture
RDD Round
SQD Square
(blank) No downlight modules in fixture
S80CRI 80 CRI
(blank) No downlight modules in fixture
S27K 2700K
S30K 3000K
S35K 3500K
S40K 4000K
NODIM 3 Non-dimming
MIN1 Constant current, dimming to 1%
DARK Constant current, dimming to 0.1%
SCT Single circuit
DCT 4 Dual circuit
(blank) No louver
LVRD 5 Dropped louver
LVRR 7 Regressed louver painted to match fixture finish
LVRRA 7 Regressed louver, aluminum finish
EGLD 5,6 Edge View direct lens
Not available with Downlights. Not available with NLTAIR2.
Must select all Downlight options.Specify number of downlights modules.Not available on 2’ or 3’ units. Not available with 347V.Maximum of 2DL in 4’ & 5’ units.
Maximum of 3DL in 6’, 7’ & 8’ units.Not available with emergency options.Not available with 4’ unit with DCT.Not available with any sensors on the same unit.
Voltage Finish Emergency Options Control Input Sensor Secondary Sensor
Not available with Downlights.Not available on 2’ or 3’ units.Not available with 347V & nLight. (Use ZT or NLTAIR2 Control Inputs where applicable.)
Tertiary Sensor Options
(blank) No additional zones/sensors
TNS Select if multi-zone fixture with no sensor in tertiary zone
GLR 15 Fast-blow fuse
GMF 15 Slow-blow fuse
WL 15 Wet Location
DPL Damp Location
USPOM US point of assembly
Notes:1. Limited to 400LMF to 1000LMF in 50LMF increments. Not available
with ECOD, ECOD2, ECOD5 or DMX control input. 2. Not available with NLTAIR2.3. Not available with Control Inputs.4. Not available with 2’ or 3’ units, DMX or NLTAIR2. Not available
with E10WLCP on 4’ unit.5. Not available with Sensor Options.6. Not available with Emergency Options7. Not available with sensors on 2’, 3’ & 4’ units.8. DCT not available with 2’ & 3’ units with 347, with ZT & sensors,
with NLTAIR2, with emergency options, with NLIGHT/PP in 5’ units, with NLIGHT/PP & downlights.
9. Not available with 2’ or 3’ units, or 4’ with DCT. Not available with DMX control option. One battery pack per unit. Only available on 8’ unit with ECOD, ECOD2, ECOD5. Not available on 5’ unit with NLTAIR. If with SCT, ZT & API or APD, only available in 7’ & 8’ units. Not available with DCT & sensors. Not available with DCT & nLight in same unit.
10. Powers entire direct unit. Not available with DCT & sensors. Not available with DCT & NLTAIR2. Not available with DMX.
11. Must select 120 or 277 volt. Remote mounted. Not available with sensors. Not available with DCT & NLTAIR2. Not available with DMX.
12. Comes with white CAT5 cord in addition to the standard power cord. Will require remote mounted nIO on 2’ unit.
13. Must select MIN1 or DARK Dim Level. Not available with WW or DCT options on 2’ or 3’ units. If ordered with E10WLCP, only available in 7’ & 8’ units.
14. Must select DARK Dim Level.15. Not available with 347V.16. Must select MIN1 Dim Level. Not available on 2’, 3’ or 5’ units.17. Not available with 347v on 2’, 3’, 5’ or 6’ units.18. 120V only.19. Requires ZT or NLIGHT Control Input.20. Requires ZT, NLIGHT or NLTAIR2 Control Input.
Mark Lighting offers the ability to provide a continuous run plan to suit your requirements by optionally offering three different methods of configuration.
LLP- Linear Longest PossibleIn this configuration, the longest length available is optimized, resulting in the fewest segments and mounting locations. Caution, should be used where balanced appearance is a concern. Example: 20 FT run would have 2, 8 FT segment and 1, 4 FT segment at the end of the run.
LCB- Linear Center Balanced:This configuration incorporates the longest center segment(s) along with any additional lengths required to fill the run length, added to the run ends. Example: 16 FT run would have 2, 4 FT segments (one at each end) and 1, 8 FT segment in the center.
8 FT 8 FT 4FTLLP
4 FT 8 FT 4FTLCB
This system is not modular. Runs longer that 8FT will be automatically configured with Starter, Middle and Ender sections, based on how you specify the TOTAL RUN LENGTH and MAXIMUM SECTION LENGTH parameters in the ordering information. Always order the total run length, not the individual sections
32FT
8FT 8FT 8FT 8FT
Example: This run must be ordered as 1pc "S4LS LLP 32FT MSL8..."
PRIMARY ZONE:ADC (DAYLIGHT SENSOR). SINCE THERE IS NO NUMBER AFTER THE ADC SENSOR NOMENCLATURE, THE SENSOR WILL CONTROL THE ENTIRE RUN.
TOTAL RUN LENGTH
The run will be broken out using as many sections at the chosen MSL length as possible. Shorter sections will then complete the desired run length.
Run Patterns, Corners and JunctionSlot 4 LED patterns be configured in 1’ increments with illuminated 90° inside and outside corners, T junctions, and X junctions with standard 2’ corner and junction lengths. For custom angles, corner or junction lengths, consult factory.See separate pattern spec sheet for details.
DownlightsOptional downlights powered by Xicato Spot Modules are available with 4’, 5’, 6’, and 8’ length luminaires, maximum (2) Xicato downlights per length. Each downlight module is 10W with 700 lumens delivered, 28 degree beam spread.. Downlights are supplied with a dedicated feed point and will be controlled separately.
Continuous RunsSlot 4 LED continuous rows can be configured in 1’ increments and featuring the AEL precision joiner to create a hairline seam between luminaires, providing a monolithic visual aesthetic. For custom run lengths less than a 1’ increment, consult factory.
Standard Downlight Location
Other Downlight Configuration (consult factory)
MARK ARCHITECTURALLIGHTING TM
Slot 4 LED Surface Mount
Our surface product mounts to hard/sheetrock ceilings only. Consult manufacturing for use with a grid ceiling.
At the 7.5 ft (2.9 m) hanging height of a typical pendant mount fixture the sensor provides 10 ft (3.05 m) radial detection of small motion. At a 9 ft (2.74 m) hanging height the radius is 12 ft (3.66 m) for small motion.
Adequate for walking motion detection from mounting heights between 7.5 ft (2.29 m) and 20 ft (6.10 m).
Initial detection will occur earlier when walking across sensor’s field of view than when walking directly at sensor.
Initial detection of walking motion into long coverage segment will occur at distances of 2x the mounting height up to 15 ft (4.57 m) and 1.75x up to 20 ft (6.10 m). Lens assembly rotates 15° to enable adjustment in order to line up long segments.
Lens rotates 15° to enable adjustment
1512.510752.50 ft2.5571012.515
4.53.832.51.50.750 m0.751.52.533.84.5
OCCUPANCY DETECTION COVERAGE
Integrated ControlsOptional nLight® integrated controls make Slot LED luminaires addressable- allowing them to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices using standard CAT5 Cabling.
Occupancy Sensor (MSD9N) and/or Photocell (DSCC)
MARK ARCHITECTURALLIGHTING TM
Slot 4 LED Surface Mount
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 2 SENSORS WITH PRIMARY ZONE 24FT AND SECONDARY ZONE 8FT -- PDT24 SADC8
PRIMARY ZONE:PDT24 (DUAL TECH SENSOR, 24FT ZONE)
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 1 SENSOR ALL ONE ZONE -- ADC
PRIMARY ZONE:ADC (DAYLIGHT SENSOR). SINCE THERE IS NO NUMBER AFTER THE ADC SENSOR NOMENCLATURE, THE SENSOR WILL CONTROL THE ENTIRE RUN.
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 1 SENSOR ALL ONE ZONE -- PDT16
DOES NOT WORK BECAUSE THE LENGTH OF THE ZONE SPECIFIED (16FT),DOES NOT MATCH THE ENTIRE RUN (32FT)
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 2 SENSORS WITH PRIMARY ZONE 20FT AND SECONDARY ZONE 12FT -- PDT20 SADC12
INCORRECT:
NOTE: IF THERE IS ONLY ONE ZONE, LEAVE THE NUMBERS AFTER THE SENSOR NOMENCLATURE BLANK. EXAMPLE: NO PDT16, USE PDT
DOES NOT WORK BECAUSE THE LENGTH OF THE ZONES SPECIFIED (20FT AND 12FT),DOES NOT WORK FOR 8FT FIXTURE SECTIONS, ZONES CANNOT SPLIT A FIXTURE SECTION
PRIMARY ZONE: 20FTSECONDARY ZONE: 12FT
Notes: • Only one sensor per zone • At the most, the entire run can only have 2 sensors (thus 2 sensors zones at the most) • Sensor zone can not split fixture sections • No overlapping zones
CORRECT:
SECONDARY ZONE:SADC (DAYLIGHT SENSOR, 8FT ZONE)
Total Run Length to Order
Total Run Length to Order
For runs longer than 8FT: ALWAYS order the run by the TOTAL RUN LENGTH. Ordering the sections individually will not provide the correct joining hardware to allow connection in the field.
MIN1 + ECOD2 = Lutron forward phase control 100 to 1% LUTRON Hi-lume 1% 2-wire (model LTEA4U1U)
MIN1 + ECOD5 = Lutron Ecosystem 100 to 5% LUTRON 5-Seires EcoSystem LED Driver (model LDE5)
MIN1 ECOD Lutron Ecosystem 100 to 1% LUTRON Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black (model LDE1)
DARK ZT 0-10V eldoLED SOLOdrive 100 to 0.1% Formerly (EZB) nomenclature. Linear dimming
DARK NLIGHT 0-10V eldoLED SOLOdrive 100 to 0.1% Logarithmic dimming
DARK DALI DALI compatible eldoLED SOLOdrive 100 to 0.1% "Compatible with DALI. Formerly (EDB & EDAB)
nomenclature." Logarithmic dimming
DARK DMX DMX compatible eldoLED POWERdrive 100 to 0.1% "Compatible with DMX / Remote Device Management.
Formerly (EXB & EDXB) nomenclature." Linear dimming
Intelligent Luminaire Technology Guide
Choose nomenclature from these columns
Cont
rol /
Sen
sor
Conf
igur
atio
ns
Control Input Sensor Sensor Notes
ZT + API = MSD 7 ADCXIndividual fixture control only. PIR integral occupancy sensor with automatic dimming control photocell. (Old nomenclature: ZT + PIR + ADC)
ZT + APD = MSD PDT 7 ADCXIndividual fixture control only. PDT integral occupancy sensor with automatic dimming control photocell. (Old nomenclature: ZT + PDT + ADC)
NLIGHT + (blank) = nIO EZ PH nLight enabled only. No onboard sensor.
NLIGHT EMG = nIO EZ PH ER Emergency nLight enabled only. No onboard sensor.
NLIGHT + API = nIO EZ PH + nES 7 ADCX nLight nES 7 ADCX PIR integral occupancy sensor with automatic dimming photocell. (Old nomenclature: NLIGHT + PIR + ADC)
NLIGHT + PDT = nIO EZ PH + nES PDT 7 nLight nES PDT 7 dual technology integral occupancy sensor. (Old nomenclature: NLIGHT + PDT)
NLIGHT + APD = nIO EZ PH + nES PDT 7 ADCXnLight nES PDT 7 dual technology integral occupancy sensor with automatic dimming photocell. (Old nomenclature: NLIGHT + PDT + ADC)
NLTAIR2 (blank) RIO EZDL 90D G2 https://www.acuitybrands.com/products/detail/778845/nLight/rIO/Fixture-embedded-nLight-AIR-network-interface
NLTAIR2 API RES7 G2 https://www.acuitybrands.com/products/detail/593899/nLight/RES7-Sensor/nLight-AIR-Fixture-Integrated-Wireless-Sensor
Slot 4 LED Surface MountThe Slot LED family of luminaires offers an unparalleled package of performance and features for your next lighting project. Precision lumen DIRECTIR optics deliver optimized light where needed for ceilings and walls. With other key features such as simplified installation, seamless controls integration and superior LED color constancy, the Slot LED family from Mark Lighting offers exceptional quality and design flexibility.
Technical Drawing
Type:
Project:
Catalog Number:DO NOT TYPE HERE. Autopopulated field.
HousingNominal 3.5” x 3.75” extruded aluminum housing FinishWhite, Black or Silver powdercoat ReflectorFormed steel with high reflectance white.Distribution/ShieldingExtruded 90% transmissive acrylic lens with a textured surface providing diffuse illumination and a uniform appearance for direct lambertian distribution (No Optics). Wall Wash (WW) and Wall Graze (WG) distribution options incorporate co-extruded lenses. Shielding is available as an external blade louver for WW or WG options, or an internal blade louver in lieu of lambertian distribution diffuser.LED ComponentsLinear: Nichia®- 757 series LED chips (>80 CRI)ElectricalLong-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality of illumination for extended service life. 80% LED lumen maintenance at 60,000 hours (L80/60,000).Color ConsistencyThe Acuity Brands circuit boards for the linear LED components use a precise binning algorithm which creates a consistent color temperature from board to board. The color a variation of no greater than a 2.5 Step MacAdam (2.5SDCM) along the black body locus from board to board.DrivereldoLED® driver provides natural dimming with smooth, continuous and flicker-free deep dimming. Supports operation between 120VAC and 277 VAC, with low inrush current (NEMA 410) and THD < 20%. Meets FCC Title 47 C.F.R. 15 Class A or Class B requirements. Lutron high performance driver options also available.Certification CSA tested to UL 1598 standards, assembled in the USA. Damp location listed.Listings DesignLights Consortium® (DLC) Premium qualified product. Not all versions of this product may be DLC Premium qualified. Please check the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are qualified.Warranty5-year limited warranty. Complete warranty terms located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspxNote: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 °C. Specifications subject to change without notice.
Specification Features
Direct Surface
3 1/2
3 3/4
4FT INDIVIDUAL (35K) DIRECT
Lumens Output 400LMF 600LMF 800LMF 1000LMF
Delivered Lumens 1800 2707 3571 4103
Input Watts 15.4 23.4 32 37.3
Lumen/Watt 117 115 112 110
Fixture Performance
* Consult factory for customized lumen output and wattage between 350LMF and 1050LMF.
A+ Capable Luminaire This item is an A+ capable luminaire, which has been designed and tested to provide consistent color appearance and out-of-the-box control compatibility with simple commissioning.
• All configurations of this luminaire meet the Acuity Brands’ specification for chromatic consistency
• This luminaire is part of an A+ Certified solution for nLight® control networks when ordered with drivers marked by a shaded background*
• This luminaire is part of an A+ Certified solution for nLight control networks, providing advanced control functionality at the luminaire level, when selection includes driver and control options marked by a shaded background*
To learn more about A+, visit www.acuitybrands.com/aplus.
_FT Specify continuous run length (in whole feet, 2' minimum)
Unit length may affect available options. 2’ & 3’ only available as individual units
For runs longer than 8FT: ALWAYS order the run by the TOTAL RUN LENGTH. Ordering the sections individually will not provide the correct joining hardware to allow connection in the field.
MSL4 4’
MSL5 5’
MSL6 6’
MSL7 7’
MSL8 8’
80CRI 80 CRI
90CRI 90 CRI
27K 2700K
30K 3000K
35K 3500K
40K 4000K
50K 5000K
400LMF 400 lumens per FT
600LMF 600 lumens per FT
800LMF 800 lumens per FT
1000LMF 1000 lumens per FT
_LMF 1 # lumens per FT
(blank) Standard lambertian distribution
WW 2 Wallwash distributions
WG Wall graze distribution
WW and WG not available with Downlights, EGLD, LVRR or LVRRA.
Downlight Downlight Shape Downlight Color Rendering Downlight Color Temp Minimum Dimming Level Switching Optional Shielding
(blank) No Downlight modules in fixture
2DL LED downlights (2 per unit)
_DL LED downlights per run (3DL, 4DL, etc.)
(blank) No downlight modules in fixture
RDD Round
SQD Square
(blank) No downlight modules in fixture
S80CRI 80 CRI
(blank) No downlight modules in fixture
S27K 2700K
S30K 3000K
S35K 3500K
S40K 4000K
NODIM 3 Non-dimming
MIN1 Constant current, dimming to 1%
DARK Constant current, dimming to 0.1%
SCT Single circuit
DCT 4 Dual circuit
(blank) No louver
LVRD 5 Dropped louver
LVRR 7 Regressed louver painted to match fixture finish
LVRRA 7 Regressed louver, aluminum finish
EGLD 5,6 Edge View direct lens
Not available with Downlights. Not available with NLTAIR2.
Must select all Downlight options.Specify number of downlights modules.Not available on 2’ or 3’ units. Not available with 347V.Maximum of 2DL in 4’ & 5’ units.
Maximum of 3DL in 6’, 7’ & 8’ units.Not available with emergency options.Not available with 4’ unit with DCT.Not available with any sensors on the same unit.
Voltage Finish Emergency Options Control Input Sensor Secondary Sensor
Not available with Downlights.Not available on 2’ or 3’ units.Not available with 347V & nLight. (Use ZT or NLTAIR2 Control Inputs where applicable.)
Tertiary Sensor Options
(blank) No additional zones/sensors
TNS Select if multi-zone fixture with no sensor in tertiary zone
GLR 15 Fast-blow fuse
GMF 15 Slow-blow fuse
WL 15 Wet Location
DPL Damp Location
USPOM US point of assembly
Notes:1. Limited to 400LMF to 1000LMF in 50LMF increments. Not available
with ECOD, ECOD2, ECOD5 or DMX control input. 2. Not available with NLTAIR2.3. Not available with Control Inputs.4. Not available with 2’ or 3’ units, DMX or NLTAIR2. Not available
with E10WLCP on 4’ unit.5. Not available with Sensor Options.6. Not available with Emergency Options7. Not available with sensors on 2’, 3’ & 4’ units.8. DCT not available with 2’ & 3’ units with 347, with ZT & sensors,
with NLTAIR2, with emergency options, with NLIGHT/PP in 5’ units, with NLIGHT/PP & downlights.
9. Not available with 2’ or 3’ units, or 4’ with DCT. Not available with DMX control option. One battery pack per unit. Only available on 8’ unit with ECOD, ECOD2, ECOD5. Not available on 5’ unit with NLTAIR. If with SCT, ZT & API or APD, only available in 7’ & 8’ units. Not available with DCT & sensors. Not available with DCT & nLight in same unit.
10. Powers entire direct unit. Not available with DCT & sensors. Not available with DCT & NLTAIR2. Not available with DMX.
11. Must select 120 or 277 volt. Remote mounted. Not available with sensors. Not available with DCT & NLTAIR2. Not available with DMX.
12. Comes with white CAT5 cord in addition to the standard power cord. Will require remote mounted nIO on 2’ unit.
13. Must select MIN1 or DARK Dim Level. Not available with WW or DCT options on 2’ or 3’ units. If ordered with E10WLCP, only available in 7’ & 8’ units.
14. Must select DARK Dim Level.15. Not available with 347V.16. Must select MIN1 Dim Level. Not available on 2’, 3’ or 5’ units.17. Not available with 347v on 2’, 3’, 5’ or 6’ units.18. 120V only.19. Requires ZT or NLIGHT Control Input.20. Requires ZT, NLIGHT or NLTAIR2 Control Input.
Mark Lighting offers the ability to provide a continuous run plan to suit your requirements by optionally offering three different methods of configuration.
LLP- Linear Longest PossibleIn this configuration, the longest length available is optimized, resulting in the fewest segments and mounting locations. Caution, should be used where balanced appearance is a concern. Example: 20 FT run would have 2, 8 FT segment and 1, 4 FT segment at the end of the run.
LCB- Linear Center Balanced:This configuration incorporates the longest center segment(s) along with any additional lengths required to fill the run length, added to the run ends. Example: 16 FT run would have 2, 4 FT segments (one at each end) and 1, 8 FT segment in the center.
8 FT 8 FT 4FTLLP
4 FT 8 FT 4FTLCB
This system is not modular. Runs longer that 8FT will be automatically configured with Starter, Middle and Ender sections, based on how you specify the TOTAL RUN LENGTH and MAXIMUM SECTION LENGTH parameters in the ordering information. Always order the total run length, not the individual sections
32FT
8FT 8FT 8FT 8FT
Example: This run must be ordered as 1pc "S4LS LLP 32FT MSL8..."
PRIMARY ZONE:ADC (DAYLIGHT SENSOR). SINCE THERE IS NO NUMBER AFTER THE ADC SENSOR NOMENCLATURE, THE SENSOR WILL CONTROL THE ENTIRE RUN.
TOTAL RUN LENGTH
The run will be broken out using as many sections at the chosen MSL length as possible. Shorter sections will then complete the desired run length.
Run Patterns, Corners and JunctionSlot 4 LED patterns be configured in 1’ increments with illuminated 90° inside and outside corners, T junctions, and X junctions with standard 2’ corner and junction lengths. For custom angles, corner or junction lengths, consult factory.See separate pattern spec sheet for details.
DownlightsOptional downlights powered by Xicato Spot Modules are available with 4’, 5’, 6’, and 8’ length luminaires, maximum (2) Xicato downlights per length. Each downlight module is 10W with 700 lumens delivered, 28 degree beam spread.. Downlights are supplied with a dedicated feed point and will be controlled separately.
Continuous RunsSlot 4 LED continuous rows can be configured in 1’ increments and featuring the AEL precision joiner to create a hairline seam between luminaires, providing a monolithic visual aesthetic. For custom run lengths less than a 1’ increment, consult factory.
Standard Downlight Location
Other Downlight Configuration (consult factory)
MARK ARCHITECTURALLIGHTING TM
Slot 4 LED Surface Mount
Our surface product mounts to hard/sheetrock ceilings only. Consult manufacturing for use with a grid ceiling.
At the 7.5 ft (2.9 m) hanging height of a typical pendant mount fixture the sensor provides 10 ft (3.05 m) radial detection of small motion. At a 9 ft (2.74 m) hanging height the radius is 12 ft (3.66 m) for small motion.
Adequate for walking motion detection from mounting heights between 7.5 ft (2.29 m) and 20 ft (6.10 m).
Initial detection will occur earlier when walking across sensor’s field of view than when walking directly at sensor.
Initial detection of walking motion into long coverage segment will occur at distances of 2x the mounting height up to 15 ft (4.57 m) and 1.75x up to 20 ft (6.10 m). Lens assembly rotates 15° to enable adjustment in order to line up long segments.
Lens rotates 15° to enable adjustment
1512.510752.50 ft2.5571012.515
4.53.832.51.50.750 m0.751.52.533.84.5
OCCUPANCY DETECTION COVERAGE
Integrated ControlsOptional nLight® integrated controls make Slot LED luminaires addressable- allowing them to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices using standard CAT5 Cabling.
Occupancy Sensor (MSD9N) and/or Photocell (DSCC)
MARK ARCHITECTURALLIGHTING TM
Slot 4 LED Surface Mount
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 2 SENSORS WITH PRIMARY ZONE 24FT AND SECONDARY ZONE 8FT -- PDT24 SADC8
PRIMARY ZONE:PDT24 (DUAL TECH SENSOR, 24FT ZONE)
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 1 SENSOR ALL ONE ZONE -- ADC
PRIMARY ZONE:ADC (DAYLIGHT SENSOR). SINCE THERE IS NO NUMBER AFTER THE ADC SENSOR NOMENCLATURE, THE SENSOR WILL CONTROL THE ENTIRE RUN.
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 1 SENSOR ALL ONE ZONE -- PDT16
DOES NOT WORK BECAUSE THE LENGTH OF THE ZONE SPECIFIED (16FT),DOES NOT MATCH THE ENTIRE RUN (32FT)
32FT
8FT 8FT 8FT 8FT32FT MSL8 RUN WITH 2 SENSORS WITH PRIMARY ZONE 20FT AND SECONDARY ZONE 12FT -- PDT20 SADC12
INCORRECT:
NOTE: IF THERE IS ONLY ONE ZONE, LEAVE THE NUMBERS AFTER THE SENSOR NOMENCLATURE BLANK. EXAMPLE: NO PDT16, USE PDT
DOES NOT WORK BECAUSE THE LENGTH OF THE ZONES SPECIFIED (20FT AND 12FT),DOES NOT WORK FOR 8FT FIXTURE SECTIONS, ZONES CANNOT SPLIT A FIXTURE SECTION
PRIMARY ZONE: 20FTSECONDARY ZONE: 12FT
Notes: • Only one sensor per zone • At the most, the entire run can only have 2 sensors (thus 2 sensors zones at the most) • Sensor zone can not split fixture sections • No overlapping zones
CORRECT:
SECONDARY ZONE:SADC (DAYLIGHT SENSOR, 8FT ZONE)
Total Run Length to Order
Total Run Length to Order
For runs longer than 8FT: ALWAYS order the run by the TOTAL RUN LENGTH. Ordering the sections individually will not provide the correct joining hardware to allow connection in the field.
MIN1 + ECOD2 = Lutron forward phase control 100 to 1% LUTRON Hi-lume 1% 2-wire (model LTEA4U1U)
MIN1 + ECOD5 = Lutron Ecosystem 100 to 5% LUTRON 5-Seires EcoSystem LED Driver (model LDE5)
MIN1 ECOD Lutron Ecosystem 100 to 1% LUTRON Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black (model LDE1)
DARK ZT 0-10V eldoLED SOLOdrive 100 to 0.1% Formerly (EZB) nomenclature. Linear dimming
DARK NLIGHT 0-10V eldoLED SOLOdrive 100 to 0.1% Logarithmic dimming
DARK DALI DALI compatible eldoLED SOLOdrive 100 to 0.1% "Compatible with DALI. Formerly (EDB & EDAB)
nomenclature." Logarithmic dimming
DARK DMX DMX compatible eldoLED POWERdrive 100 to 0.1% "Compatible with DMX / Remote Device Management.
Formerly (EXB & EDXB) nomenclature." Linear dimming
Intelligent Luminaire Technology Guide
Choose nomenclature from these columns
Cont
rol /
Sen
sor
Conf
igur
atio
ns
Control Input Sensor Sensor Notes
ZT + API = MSD 7 ADCXIndividual fixture control only. PIR integral occupancy sensor with automatic dimming control photocell. (Old nomenclature: ZT + PIR + ADC)
ZT + APD = MSD PDT 7 ADCXIndividual fixture control only. PDT integral occupancy sensor with automatic dimming control photocell. (Old nomenclature: ZT + PDT + ADC)
NLIGHT + (blank) = nIO EZ PH nLight enabled only. No onboard sensor.
NLIGHT EMG = nIO EZ PH ER Emergency nLight enabled only. No onboard sensor.
NLIGHT + API = nIO EZ PH + nES 7 ADCX nLight nES 7 ADCX PIR integral occupancy sensor with automatic dimming photocell. (Old nomenclature: NLIGHT + PIR + ADC)
NLIGHT + PDT = nIO EZ PH + nES PDT 7 nLight nES PDT 7 dual technology integral occupancy sensor. (Old nomenclature: NLIGHT + PDT)
NLIGHT + APD = nIO EZ PH + nES PDT 7 ADCXnLight nES PDT 7 dual technology integral occupancy sensor with automatic dimming photocell. (Old nomenclature: NLIGHT + PDT + ADC)
NLTAIR2 (blank) RIO EZDL 90D G2 https://www.acuitybrands.com/products/detail/778845/nLight/rIO/Fixture-embedded-nLight-AIR-network-interface
NLTAIR2 API RES7 G2 https://www.acuitybrands.com/products/detail/593899/nLight/RES7-Sensor/nLight-AIR-Fixture-Integrated-Wireless-Sensor
Remote BGTD Mounting OptionRecessed in sheetrock ceiling; rod mounted to structure. Consult factory for other ceiling types or canopy options.
6 foot flexible conduit included, BGTD option should be mounted within 6 feet of junction box above fixture.
Accessible Ceiling
Everly LED Outdoor SconceEVYW Series
Features This outdoor LED light is ideal for security and general lighting.Available in 1-light and 2-light. Provides lighting in residential, commercial, and hospitality applications.Fixture mounts to standard junction box (not included).
Construction Standard mounting holes and hardware are included. Power supply connections must be made inside a junction box (not included).
Finish Black powder coated finish.
Diffuser Clear diffuser.
Electrical This unit is direct wired with a low voltage electronic LED driver.The constant current LED driver is rated for 120-277 VAC input,Minimum starting temp -20°F.
LampingFixture includes a LED modules capable of producing:8” - 12W, 1000 source lumens12” - 24W, 1800 source lumens3000K (CCT). Rated for 50,000 Hrs. 90 CRI.
Certification All fixtures are cETLus listed for wet locations.
Warranty Limited warranty: This fixture is free fromdefects in materials and workmanship fora period of 5 years from date of purchase.
Specifications and dimensions subject to change without notice.
2345 N. Ernie Krueger Circle • Waukegan, IL. 60087 • P: 847.249.5970 • F: 847.249.2618 • AFXinc.com R0/18
DATELOCATION
PREPAREDBY
COMMENTS
CATALOG NUMBER
QUANTITY
FIXTURE TYPE
Ordering Information:Black LED Lumens CCT H W D EVYW070410L30MVBK (1-Light) 12W 1000 3000K 8” 4-1/4” 7”EVYW070418L30MVBK (2-Light) 24W 1800 3000K 12” 4-1/4” 7”
Source
1-Light
2-Light
EVYW070410L30MVBK
Type Z03
>2025 First Avenue, Suite 300, Seattle, WA 98121-3131 206 441 4522 / nacarchitecture.com
Seattle / Spokane / Los Angeles
Cascadia Montessori School
East Building Remodel and Addition
Roof Plan Waiver
Cascadia Montessori School Remodel and Addition is proposing no rooftop mechanical equipment
resulting in no rooftop mechanical equipment screening.