Sharp Error Codes

Sharp Printers Error codes

BRAND MODEL ERROR CO DescriptionSHARP 2014 L1-0 Scanner position errorSHARP 2014 L3-0 Scanner position errorSHARP 2014 L4-1 Main motor drive overloadedSHARP 2014 L5-2 Lens position errorSHARP 2014 L8-1 zero cross signal errorSHARP 2014 L8-3 auto-exposure sensor malfunctionSHARP 2014 H2-0 Fusing unit temperature errorSHARP 2014 H3-0 Overheated fusing unitSHARP 2014 H4-0 The fusing unit doesn't heat upSHARP 2014 U2-1 EPROM errorSHARP 2014 U2-4 Memory back-up battery deadSHARP 2014 U5-5 Optics cavity overheatedSHARP 2014 EE-EU Low toner density in the developerSHARP 2014 EE-EL High toner density in the developerSHARP 2014 CH open cover in the paper feed areaSHARP 2014 CH blinkingDev unit is not properly installedSHARP 2014 PC Key counter not installedSHARP 2020 P Add paperSHARP 2020 CC No original detected in the feederSHARP 2020 CH Sorter problemsSHARP 2020 CH blinkingDev unit is not properly installedSHARP 2020 PC Key counter not installedSHARP 2020 L1 Scanner position errorSHARP 2020 L3 Scanner position errorSHARP 2020 L4 Main motor drive overloadedSHARP 2020 L5 Lens position errorSHARP 2020 L8-01 Main board malfunctionSHARP 2020 L8-03 auto-exposure sensor malfunctionSHARP 2020 H2-00 Fusing unit temperature errorSHARP 2020 H3-00 Overheated fusing unitSHARP 2020 H4-00 The fusing unit doesn't heat upSHARP 2020 U2-01 Memory back-up battery deadSHARP 2020 U2-04 EPROM errorSHARP 2020 U5-00 Communication with the ADF is lostSHARP 2020 U5-01 Registration sensor problem in ADFSHARP 2020 U5-02 Paper exit sensor problem in ADFSHARP 2020 U5-11 Misfeed in ADFSHARP 2020 U5-16 ADF cooling fan overloadedSHARP 2020 F1-00 Lost communication with the SorterSHARP 2020 F1-02 Sorter main drive overloadedSHARP 2020 F1-04 Bin limit position sensor error in sorterSHARP 2020 F1-05 Bin position error in sorter

www.it-expertzone.com

SHARP 2020 F1-06 Paper exit drive overloaded in sorterSHARP 2020 F1-14 Paper sensor eror in sorterSHARP 2020 F1-16 Paper transport motor overloaded in sorterSHARP 2020 F2-31 ID sensor errorSHARP 2020 F2-32 ID pattern reading errorSHARP 2020 F2-33 Grid voltage errorSHARP 2020 F2-35 Grid voltage errorSHARP 2020 F2-37 ID pattern reading errorSHARP 2020 EE-EU Low toner density in the developerSHARP 2020 EE-EL High toner density in the developerSHARP 2114 L1-0 Scanner position errorSHARP 2114 L3-0 Scanner position errorSHARP 2114 L4-1 Main motor drive overloadedSHARP 2114 L5-2 Lens position errorSHARP 2114 L8-1 zero cross signal errorSHARP 2114 L8-3 auto-exposure sensor malfunctionSHARP 2114 H2-0 Fusing unit temperature errorSHARP 2114 H3-0 Overheated fusing unitSHARP 2114 H4-0 The fusing unit doesn't heat upSHARP 2114 U2-1 EPROM errorSHARP 2114 U2-4 Memory back-up battery deadSHARP 2114 U5-5 Optics cavity overheatedSHARP 2114 EE-EU Low toner density in the developerSHARP 2114 EE-EL High toner density in the developerSHARP 2114 CH open cover in the paper feed areaSHARP 2114 CH blinkingDev unit is not properly installedSHARP 2114 PC Key counter not installedSHARP 2116 L1-00 Scanner position errorSHARP 2116 L3-00 Scanner position errorSHARP 2116 L4-01 Main motor drive overloadedSHARP 2116 L5-02 Lens position errorSHARP 2116 L8-01 zero cross signal errorSHARP 2116 L8-03 auto-exposure sensor malfunctionSHARP 2116 H2-00 Fusing unit temperature errorSHARP 2116 H3-00 Overheated fusing unitSHARP 2116 H4-00 The fusing unit doesn't heat upSHARP 2116 U2-01 Memory back-up battery deadSHARP 2116 U2-04 EPROM errorSHARP 2116 U5-00 Communication with the ADF is lostSHARP 2116 U5-01 Registration sensor problem in ADFSHARP 2116 U5-02 Exit sensor error in ADFSHARP 2116 U5-11 ADF paper transport drive overloadedSHARP 2116 U5-12 Main drive overloaded in ADFSHARP 2116 F1-00 Lost communication with the SorterSHARP 2116 F1-02 Sorter main drive overloadedSHARP 2116 F1-04 Limit positionSHARP 2116 F1-05 Sorter bin position errorSHARP 2116 F1-06 Paper exit motor overloaded in sorter

SHARP 2116 F1-14 Paper presence sensor error in sorterSHARP 2116 F1-16 Paper transport motor overloaded in sorterSHARP 2116 F2-31 ID sensor errorSHARP 2116 F2-32 ID pattern reading errorSHARP 2116 F2-33 Grid voltage errorSHARP 2116 F2-35 Grid voltage errorSHARP 2116 F2-37 ID pattern reading errorSHARP 2116 EE-EU Low toner density in the developerSHARP 2116 EE-EL High toner density in the developerSHARP 2116 CH Sorter not installed properlySHARP 2116 CH blinkingDev unit is not properly installedSHARP 2116 P Key counter not installedSHARP 2116 P blinking Add paperSHARP 2118 L1-00 Scanner position errorSHARP 2118 L3-00 Scanner position errorSHARP 2118 L4-01 Main drive overloaded in ADFSHARP 2118 L5-02 Lens position errorSHARP 2118 L8-01 zero cross signal errorSHARP 2118 L8-03 auto-exposure sensor malfunctionSHARP 2118 H2-00 Fusing unit temperature errorSHARP 2118 H3-00 Overheated fusing unitSHARP 2118 H4-00 The fusing unit doesn't heat upSHARP 2118 U2-01 Memory back-up battery deadSHARP 2118 U2-04 EPROM errorSHARP 2118 U5-00 Communication with the ADF is lostSHARP 2118 U5-01 Registration sensor problem in ADFSHARP 2118 U5-02 Exit sensor error in ADFSHARP 2118 U5-11 Paper feed sensor error in ADFSHARP 2118 U5-12 Paper feed motor overloaded in ADFSHARP 2118 F1-00 Lost communication with the SorterSHARP 2118 F1-02 Sorter main drive overloadedSHARP 2118 F1-04 Bin position error in sorterSHARP 2118 F1-05 Bin position error in sorterSHARP 2118 F1-06 Paper exit drive overloaded in sorterSHARP 2118 F1-14 Paper presence sensor error in sorterSHARP 2118 F1-16 Paper transport motor overloaded in sorterSHARP 2118 F2-31 ID pattern reading errorSHARP 2118 F2-32 ID pattern reading errorSHARP 2118 F2-33 Grid voltage errorSHARP 2118 F2-35 Grid voltage errorSHARP 2118 F2-37 ID pattern reading errorSHARP 2118 EE-EU Low toner density in the developerSHARP 2118 EE-EL High toner density in the developerSHARP 2118 CH Sorter not installed properlySHARP 2118 CH blinkingDev unit is not properly installedSHARP 2118 P Key counter not installedSHARP 2118 P blinking Misfeed SHARP 2120 P Add paper

SHARP 2120 CC No original detected in the feederSHARP 2120 CH Sorter problemsSHARP 2120 CH blinkingDev unit is not properly installedSHARP 2120 PC Key counter not installedSHARP 2120 L1 Scanner position errorSHARP 2120 L3 Scanner position errorSHARP 2120 L4 Main drive overloaded SHARP 2120 L5 Lens position errorSHARP 2120 L8-01 Main board malfunctionSHARP 2120 L8-03 auto-exposure sensor malfunctionSHARP 2120 H2-00 Fusing unit temperature errorSHARP 2120 H3-00 Overheated fusing unitSHARP 2120 H4-00 The fusing unit doesn't heat upSHARP 2120 U2-01 Memory back-up battery deadSHARP 2120 U2-04 EPROM errorSHARP 2120 U4-00 Duplex disconnectedSHARP 2120 U4-02 Allignment motor in duplex overloadedSHARP 2120 U4-03 Invertor motor in duplex overloadedSHARP 2120 U4-12 Duplex drive overloadedSHARP 2120 U5-00 Communication with the ADF is lostSHARP 2120 U5-01 Registration sensor problem in ADFSHARP 2120 U5-02 Exit sensor error in ADFSHARP 2120 U5-11 Paper feed error in ADFSHARP 2120 U5-16 ADF cooling fan overloadedSHARP 2120 F1-00 Lost communication with the SorterSHARP 2120 F1-02 Sorter main drive overloadedSHARP 2120 F1-04 Bin home position error in sorterSHARP 2120 F1-05 Bin home position error in sorterSHARP 2120 F1-06 Paper exit drive overloaded in sorterSHARP 2120 F1-14 Paper presence sensor error in sorterSHARP 2120 F1-16 Paper transport motor overloaded in sorterSHARP 2120 F2-31 ID pattern reading errorSHARP 2120 F2-32 ID pattern reading errorSHARP 2120 F2-33 Grid voltage errorSHARP 2120 F2-35 Grid voltage errorSHARP 2120 F2-37 ID pattern reading errorSHARP 2120 EE-EU Low toner density in the developerSHARP 2120 EE-EL High toner density in the developerSHARP 2214 L1-0 Scanner position errorSHARP 2214 L3-0 Scanner position errorSHARP 2214 L4-1 Main motor drive overloadedSHARP 2214 L5-2 Lens position errorSHARP 2214 L8-1 zero cross signal errorSHARP 2214 L8-3 auto-exposure sensor malfunctionSHARP 2214 H2-0 Fusing unit temperature errorSHARP 2214 H3-0 Overheated fusing unitSHARP 2214 H4-0 The fusing unit doesn't heat upSHARP 2214 U2-1 EPROM error

SHARP 2214 U2-4 Memory back-up battery deadSHARP 2214 U5-5 Optics cavity overheatedSHARP 2214 EE-EU Low toner density in the developerSHARP 2214 EE-EL High toner density in the developerSHARP 2214 CH open cover in the paper feed areaSHARP 2214 CH blinkingDev unit is not properly installedSHARP 2214 PC Key counter not installedSHARP 2216 P Add paperSHARP 2216 CC Original not detected in DFSHARP 2216 CH Sorter problemsSHARP 2216 CH blinkingDev unit is not properly installedSHARP 2216 PC Key counter not installedSHARP 2216 L1 Scanner position errorSHARP 2216 L3 Scanner position errorSHARP 2216 L4 Main motor drive overloadedSHARP 2216 L5 Lens position errorSHARP 2216 L8-01 Main board malfunctionSHARP 2216 L8-03 auto-exposure sensor malfunctionSHARP 2216 H2-00 Fusing unit temperature errorSHARP 2216 H3-00 Overheated fusing unitSHARP 2216 H4-00 The fusing unit doesn't heat upSHARP 2216 U2-01 Memory back-up battery deadSHARP 2216 U2-04 EPROM errorSHARP 2216 U5-00 Communication with the ADF is lostSHARP 2216 U5-01 Registration sensor problem in ADFSHARP 2216 U5-02 Exit sensor error in ADFSHARP 2216 U5-11 Paper feed drive overloaded in ADFSHARP 2216 U5-16 Cooling fan overloaded in ADFSHARP 2216 F1-00 Lost communication with the SorterSHARP 2216 F1-02 Main drive overloaded in SorterSHARP 2216 F1-04 Bin position error in sorterSHARP 2216 F1-05 Bin position error in sorterSHARP 2216 F1-06 Paper exit drive overloaded in sorterSHARP 2216 F1-14 Paper presence sensor error in sorterSHARP 2216 F1-16 Paper transport motor overloaded in sorterSHARP 2216 F2-31 ID pattern reading errorSHARP 2216 F2-32 ID pattern reading errorSHARP 2216 F2-33 Grid voltage errorSHARP 2216 F2-35 Grid voltage errorSHARP 2216 F2-37 ID pattern reading errorSHARP 2216 EE-EU Low toner density in the developerSHARP 2216 EE-EL High toner density in the developerSHARP AR160 CC Original not detected SHARP AR160 E1-00 Lost communication with the SorterSHARP AR160 E1-10 Lost communication with the SorterSHARP AR160 E1-11 ASIC errorSHARP AR160 E1-12 Image Processing Unit errorSHARP AR160 E1-13 ROM memory error

SHARP AR160 E1-14 NVRAM errorSHARP AR160 E1-15 Page memory faultSHARP AR160 E1-16 SIMM not present or installed incorectlySHARP AR160 E1-17 Page rotation error in RAMSHARP AR160 E1-80 electronic sort board errorSHARP AR160 E1-81 electronic sort board errorSHARP AR160 E1-82 electronic sort board errorSHARP AR160 E1-84 electronic sort board errorSHARP AR160 E1-88 electronic sort board errorSHARP AR160 E7-03 Lens position errorSHARP AR160 E7-04 white level calibration errorSHARP AR160 E7-05 black level calibration errorSHARP AR160 E7-12 CCD calibration errorSHARP AR160 F1-06 Shift sort motor overloadedSHARP AR160 F5-02 Exposure lamp blownSHARP AR160 F6-00 Fax board problemsSHARP AR160 F6-10 Fax board problemsSHARP AR160 F6-80 Fax board problemsSHARP AR160 F6-81 Fax board problemsSHARP AR160 F6-82 Fax board problemsSHARP AR160 F6-84 Fax board problemsSHARP AR160 F6-88 Fax board problemsSHARP AR160 F9-00 Printer board problemsSHARP AR160 F9-10 Printer board problemsSHARP AR160 F9-80 Printer board problemsSHARP AR160 F9-81 Printer board problemsSHARP AR160 F9-82 Printer board problemsSHARP AR160 F9-84 Printer board problemsSHARP AR160 F9-88 Printer board problemsSHARP AR160 H2-00 Fusing unit temperature errorSHARP AR160 H3-00 Overheated fusing unitSHARP AR160 H4-00 The fusing unit doesn't heat upSHARP AR160 L1-00 Scanner position errorSHARP AR160 L3-00 Scanner position errorSHARP AR160 L4-01 Main motor drive overloadedSHARP AR160 L4-10 Separation motor overloadedSHARP AR160 L6-10 Polygon mirror motor not up to speedSHARP AR160 L8-01 Zero cross signal errorSHARP AR160 U2-04 EPROM errorSHARP AR160 U2-11 Main counter errorSHARP AR160 U2-12 EPROM errorSHARP AR160 U3-29 Mirror position errorSHARP AR160 U9-00 Op panel problemSHARP AR160 U9-81 Op panel problemSHARP AR160 U9-82 Op panel problemSHARP AR160 U9-84 Op panel problemSHARP AR160 U9-88 Op panel problemSHARP AR160 U95 Firmware error

SHARP AR161 CC Original not detected SHARP AR161 E1-00 Lost communication with the SorterSHARP AR161 E1-10 Lost communication with the SorterSHARP AR161 E1-11 ASIC errorSHARP AR161 E1-12 Image Processing Unit errorSHARP AR161 E1-13 ROM memory errorSHARP AR161 E1-14 NVRAM errorSHARP AR161 E1-15 Page memory faultSHARP AR161 E1-16 SIMM not present or installed incorectlySHARP AR161 E1-17 Page rotation error in RAMSHARP AR161 E1-80 electronic sort board errorSHARP AR161 E1-81 electronic sort board errorSHARP AR161 E1-82 electronic sort board errorSHARP AR161 E1-84 electronic sort board errorSHARP AR161 E1-88 electronic sort board errorSHARP AR161 E7-03 Lens position errorSHARP AR161 E7-04 white level calibration errorSHARP AR161 E7-05 black level calibration errorSHARP AR161 E7-12 CCD calibration errorSHARP AR161 F1-06 Shift sort motor overloadedSHARP AR161 F5-02 Exposure lamp blownSHARP AR161 F6-00 Fax board problemsSHARP AR161 F6-10 Fax board problemsSHARP AR161 F6-80 Fax board problemsSHARP AR161 F6-81 Fax board problemsSHARP AR161 F6-82 Fax board problemsSHARP AR161 F6-84 Fax board problemsSHARP AR161 F6-88 Fax board problemsSHARP AR161 F9-00 Printer board problemsSHARP AR161 F9-10 Printer board problemsSHARP AR161 F9-80 Printer board problemsSHARP AR161 F9-81 Printer board problemsSHARP AR161 F9-82 Printer board problemsSHARP AR161 F9-84 Printer board problemsSHARP AR161 F9-88 Printer board problemsSHARP AR161 H2-00 Fusing unit temperature errorSHARP AR161 H3-00 Overheated fusing unitSHARP AR161 H4-00 The fusing unit doesn't heat upSHARP AR161 L1-00 Scanner position errorSHARP AR161 L3-00 Scanner position errorSHARP AR161 L4-01 Main motor drive overloadedSHARP AR161 L4-10 Separation motor overloadedSHARP AR161 L6-10 Polygon mirror motor not up to speedSHARP AR161 L8-01 Zero cross signal errorSHARP AR161 U2-04 EPROM errorSHARP AR161 U2-11 Main counter errorSHARP AR161 U2-12 EPROM errorSHARP AR161 U3-29 Mirror position error

SHARP AR161 U9-00 Op panel problemSHARP AR161 U9-81 Op panel problemSHARP AR161 U9-82 Op panel problemSHARP AR161 U9-84 Op panel problemSHARP AR161 U9-88 Op panel problemSHARP AR161 U95 Firmware errorSHARP AR405 C1-00 MC unit malfunctionSHARP AR405 C2-00 TC unit malfunctionSHARP AR405 E7-00 Image Processing Unit errorSHARP AR405 E7-01 Memory back-up battery deadSHARP AR405 E7-02 Laser unit problemSHARP AR405 E7-03 HDD defectiveSHARP AR405 E7-10 black level calibration errorSHARP AR405 E7-11 white level calibration errorSHARP AR405 E7-13 CCD calibration errorSHARP AR405 E7-90 Image Processing Unit errorSHARP AR405 F1-00 Lost communication with the SorterSHARP AR405 F1-01 Sorter registration problemSHARP AR405 F1-02 Paper transport motor overloaded in sorterSHARP AR405 F1-04 Bin position error in sorterSHARP AR405 F1-05 Bin position error in sorterSHARP AR405 F1-06 Shift sort motor overloadedSHARP AR405 F1-08 Stapler position errorSHARP AR405 F1-08 Stapler overloadedSHARP AR405 F1-11 Sorter problemsSHARP AR405 F1-14 Second shift tray jammedSHARP AR405 F1-15 Sorter drive problemsSHARP AR405 F1-50 Sorter not installed properlySHARP AR405 F1-80 No powerin sorterSHARP AR405 F2-00 ID pattern reading errorSHARP AR405 F2-02 Toner add mechanism malfunctionSHARP AR405 F2-31 ID pattern reading errorSHARP AR405 F2-32 ID pattern reading errorSHARP AR405 F2-39 Drum thermistor errorSHARP AR405 F3-12 Paper does not lift in the traySHARP AR405 F3-22 Paper does not lift in the traySHARP AR405 F9-00 Printer board problemsSHARP AR405 F9-01 Printer board problemsSHARP AR405 F9-02 Printer board problemsSHARP AR405 F9-03 Network card errorSHARP AR405 F9-04 Firmware errorSHARP AR405 F9-05 Not enough memorySHARP AR405 F9-10 Printer board problemsSHARP AR405 F9-90 Printer board problemsSHARP AR405 H2-00 Fusing unit temperature errorSHARP AR405 H2-01 Fusing unit temperature errorSHARP AR405 H3-00 Overheated fusing unitSHARP AR405 H3-01 Overheated fusing unit

SHARP AR405 H4-00 The fusing unit doesn't heat upSHARP AR405 H4-01 The fusing unit doesn't heat upSHARP AR405 H5-01 Papersensordefective in the fusing unitSHARP AR405 H5-02 Fusing unit temperature errorSHARP AR405 L1-00 Scanner position errorSHARP AR405 L3-00 Scanner position errorSHARP AR405 L4-01 Main motor drive overloadedSHARP AR405 L6-10 Polygon mirror motor not up to speedSHARP AR405 L8-01 Zero cross signal errorSHARP AR405 L8-02 Zero cross signal errorSHARP AR405 U2-00 EPROM errorSHARP AR405 U2-11 EPROM errorSHARP AR405 U4-02 Duplex not working properlySHARP AR405 U4-03 Duplex problemsSHARP AR405 U5-00 Communication with the ADF is lostSHARP AR405 U5-01 Registration sensor problem in ADFSHARP AR405 U5-02 Exit sensor error in ADFSHARP AR405 U5-03 Timing sensor problems in ADFSHARP AR405 U5-11 Paper feed drive overloaded in ADFSHARP AR405 U6-01 Paper lift problem in 1'st optional traySHARP AR405 U6-02 paper lift problem in 2'nd optional traySHARP AR405 U6-08 Paper feed unit without powerSHARP AR405 U6-10 PFU paper transport motor overloadedSHARP AR405 U6-22 Paper feed unit without powerSHARP AR405 U6-50 Paper feed unit not installed properlySHARP AR405 U6-51 LCT not installed properlySHARP AR405 U7-00 Main board malfunctionSHARP AR405 U9-00 Op panel problemSHARP AR405 U9-90 Op panel problemSHARP AR405 EE-EU Low toner density in the developerSHARP AR405 EE-EL High toner density in the developerSHARP AR405 FA-01 Memory back-up battery deadSHARP AR405 PC Key counter not installedSHARP AL1000 E7-03 Scanner position errorSHARP AL1000 E7-04 CCD calibration errorSHARP AL1000 E7-05 Lens position errorSHARP AL1000 E7-12 white level calibration errorSHARP AL1000 E7-14 Main board malfunctionSHARP AL1000 E7-15 Exposure lamp blownSHARP AL1000 L1-00 Scanner position errorSHARP AL1000 L3-00 Scanner position errorSHARP AL1000 L4-01 Main motor drive overloadedSHARP AL1000 L6-10 Polygon mirror motor not up to speedSHARP AL1000 H2-00 Fusing unit temperature errorSHARP AL1000 H3-00 Overheated fusing unitSHARP AL1000 H4-00 The fusing unit doesn't heat upSHARP AL1000 U2-01 Counter errorSHARP AL1000 U2-04 EPROM error

SHARP AL1000 CH blinkingDev unit is not properly installedSHARP AL1010 E7-03 Scanner position errorSHARP AL1010 E7-04 Exposure lamp blownSHARP AL1010 E7-05 CCD calibration errorSHARP AL1010 E7-12 white level calibration errorSHARP AL1010 E7-14 Main board malfunctionSHARP AL1010 E7-15 Exposure lamp blownSHARP AL1010 L1-00 Scanner position errorSHARP AL1010 L3-00 Scanner position errorSHARP AL1010 L4-01 Main motor drive overloadedSHARP AL1010 L6-10 Polygon mirror motor not up to speedSHARP AL1010 H2-00 Fusing unit temperature errorSHARP AL1010 H3-00 Overheated fusing unitSHARP AL1010 H4-00 The fusing unit doesn't heat upSHARP AL1010 U2-01 Counter errorSHARP AL1010 U2-04 EPROM errorSHARP AL1010 CH blinkingDev unit is not properly installedSHARP 7320 L1 Scanner position errorSHARP 7320 L3 Scanner position errorSHARP 7320 L5 Position error for the lens block or the 4-th/5-th mirrorsSHARP 7320 H2 The fusing unit doesn't heat upSHARP 7320 H3 Overheated fusing unitSHARP 7320 H4 The fusing unit doesn't heat upSHARP 7320 U1 Memory back-up battery deadSHARP 7320 U2 RAM errorSHARP 7320 U3 auto-exposure sensor malfunctionSHARP 7320 EE ID pattern reading errorSHARP 7320 EU ID pattern reading errorSHARP 7320 HL ID pattern reading errorSHARP 7320 CH Dev unit is not properly installedSHARP 7320 P blinking Add paperSHARP 7700 L1 Scanner position errorSHARP 7700 L3 Scanner position errorSHARP 7700 L5 Position error for the lens block or the 4-th/5-th mirrorsSHARP 7700 H2 The fusing unit doesn't heat upSHARP 7700 H3 Overheated fusing unitSHARP 7700 H4 The fusing unit doesn't heat upSHARP 7700 U1 Memory back-up battery deadSHARP 7700 U2 RAM errorSHARP 7700 U3 auto-exposure sensor malfunctionSHARP 7700 U4 Communication with the ADF is lostSHARP 7700 U Main board malfunctionSHARP 7700 CH Interlock switch problemsSHARP 7700 CH blinkingDev unit is not properly installedSHARP 7700 CE Sorter cover openSHARP 7700 PC Key counter not installedSHARP 7750 L1 Scanner position errorSHARP 7750 L3 Scanner position error

SHARP 7750 L5 Position error for the lens block or the 4-th/5-th mirrorsSHARP 7750 H2 The fusing unit doesn't heat upSHARP 7750 H3 Overheated fusing unitSHARP 7750 H4 The fusing unit doesn't heat upSHARP 7750 U1 Memory back-up battery deadSHARP 7750 U2 RAM errorSHARP 7750 U3 auto-exposure sensor malfunctionSHARP 7750 U4 Communication with the ADF is lostSHARP 7750 U Main board malfunctionSHARP 7750 CH Interlock switch problemsSHARP 7750 CH blinkingDev unit is not properly installedSHARP 7750 CE Sorter cover openSHARP 7750 PC Key counter not installedSHARP 7800 L1 Scanner position errorSHARP 7800 L2 Scanner position errorSHARP 7800 L3 Scanner position errorSHARP 7800 L4 Main motor drive overloadedSHARP 7800 L5 Position error for the lens block or the 4-th/5-th mirrorsSHARP 7800 L8 Zero cross signal errorSHARP 7800 L9 Sorter main drive overloadedSHARP 7800 H2 Fusing unit temperature errorSHARP 7800 H3 Overheated fusing unitSHARP 7800 H4 The fusing unit doesn't heat upSHARP 7800 U1 Memory back-up battery deadSHARP 7800 U2 RAM errorSHARP 7800 U3 auto-exposure sensor malfunctionSHARP 7800 U5 ADF problemsSHARP 7800 EE ID pattern reading errorSHARP 7800 EU Low toner density in the developerSHARP 7800 EL High toner density in the developerSHARP 7800 CH Cover open in the paperfeed sectionSHARP 7800 CH blinkingDev unit is not properly installedSHARP 7800 PC Key counter not installedSHARP 7800 CC Original not detectedSHARP 7850 L1 Scanner position errorSHARP 7850 L2 Scanner position errorSHARP 7850 L3 Scanner position errorSHARP 7850 L4 Main motor drive overloadedSHARP 7850 L5 Position error for the lens block or the 4-th/5-th mirrorsSHARP 7850 L8 Zero cross signal errorSHARP 7850 L9 Sorter main drive overloadedSHARP 7850 H2 Fusing unit temperature errorSHARP 7850 H3 Overheated fusing unitSHARP 7850 H4 The fusing unit doesn't heat upSHARP 7850 U1 Memory back-up battery deadSHARP 7850 U2 RAM errorSHARP 7850 U3 auto-exposure sensor malfunctionSHARP 7850 U5 ADF malfunction

SHARP 7850 EE ID pattern reading errorSHARP 7850 EU Low toner density in the developerSHARP 7850 EL High toner density in the developerSHARP 7850 CH open cover in the paper feed areaSHARP 7850 CH blinkingDev unit is not properly installedSHARP 7850 PC Key counter not installedSHARP 7850 CC Original not detectedSHARP 8500 L1 Scanner position errorSHARP 8500 L2 Scanner position errorSHARP 8500 L3 Scanner position errorSHARP 8500 L4 Main motor drive overloadedSHARP 8500 L5-0 Lens position errorSHARP 8500 L5-1 Position error for the lens block or the 4-th/5-th mirrorsSHARP 8500 L5-2 Position error for the lens block or the 4-th/5-th mirrorsSHARP 8500 L5-4 Lens position errorSHARP 8500 L6 Toner add mechanism malfunctionSHARP 8500 L9-0 Sorter bin position errorSHARP 8500 L9-1 Sorter bin position errorSHARP 8500 L9-2 Sorter bin position errorSHARP 8500 L9-10 Sorter bin position errorSHARP 8500 L9-11 Sorter bin position errorSHARP 8500 L9-12 Sorter bin position errorSHARP 8500 H2 Fusing unit temperature errorSHARP 8500 H3 Overheated fusing unitSHARP 8500 H4 The fusing unit doesn't heat upSHARP 8500 C2 Current leak at coronas or HV supply unitSHARP 8500 U1 Memory back-up battery deadSHARP 8500 U2 RAM errorSHARP 8500 U3-0 Polygon mirror motor not up to speedSHARP 8500 U3-2 Polygon mirror motor not up to speedSHARP 8500 U3-8 Polygon mirror motor not up to speedSHARP 8500 U3-10 Mirror position errorSHARP 8500 U3-20 Exposure lamp blownSHARP 8500 U3-40 Zero cross signal errorSHARP 8500 U3-80 auto-exposure sensor malfunctionSHARP 8500 U4-0 Duplex problemsSHARP 8500 U4-1 Alignment problems in duplexSHARP 8500 U4-2 Duplexmotor overloadedSHARP 8500 U5-0 Communication with the ADF is lostSHARP 8500 U5-1 Paper transport motor overloaded in ADFSHARP 8500 U5-2 Registration sensor problem in ADFSHARP 8500 UA Main board malfunctionSHARP 8500 CH open cover in the paper feed areaSHARP 8500 CH blinkingDev unit is not properly installedSHARP 8500 PC Key counter not installed