CD-C606/1900,CP-C606/1900 CD-C606 CD-C1900 CP-C606 CP-C1900 • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used. SERVICE MANUAL SHARP CORPORATION No. S3909CDC606// This document has been published to be used for after sales service only. The contents are subject to change without notice. CONTENTS Page IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY) ....................................................................................................... 2 SPECIFICATIONS ............................................................................................................................................................. 2 NAMES OF PARTS ........................................................................................................................................................... 3 OPERATION MANUAL ...................................................................................................................................................... 5 QUICK GUIDE ................................................................................................................................................................... 6 DISASSEMBLY .................................................................................................................................................................. 8 REMOVING AND REINSTALLING THE MAIN PARTS ................................................................................................... 10 ADJUSTMENT ................................................................................................................................................................. 11 NOTES ON SCHEMATIC DIAGRAM .............................................................................................................................. 13 TYPE OF TRANSISTER AND LED ................................................................................................................................. 13 WAVEFORMS OF CD CIRCUIT ...................................................................................................................................... 14 BLOCK DIAGRAM ........................................................................................................................................................... 15 SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD .............................................................................................. 18 VOLTAGE ........................................................................................................................................................................ 32 TROUBLESHOOTING ..................................................................................................................................................... 33 FUNCTION TABLE OF IC ................................................................................................................................................ 37 FL SEGMENT ................................................................................................................................................................... 42 PARTS GUIDE/EXPLODED VIEW PACKING OF THE SET (FOR U.S.A. ONLY) CD-C606 mini component system consisting of CD-C606 mini component system and CP-C606 speaker system CD-C1900 mini component system consisting of CD-C1900 mini component system and CP-C1900 speaker system Illustration: CD-C606
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
CD-C606/1900,CP-C606/1900
– 1 –
CD-C606CD-C1900CP-C606CP-C1900
• In the interests of user-safety the set should be restored to itsoriginal condition and only parts identical to those specified beused.
SERVICE MANUAL
SHARP CORPORATION
No. S3909CDC606//
This document has been published to be usedfor after sales service only.The contents are subject to change without notice.
CONTENTSPage
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)....................................................................................................... 2SPECIFICATIONS ............................................................................................................................................................. 2NAMES OF PARTS ........................................................................................................................................................... 3OPERATION MANUAL ...................................................................................................................................................... 5QUICK GUIDE ................................................................................................................................................................... 6DISASSEMBLY .................................................................................................................................................................. 8REMOVING AND REINSTALLING THE MAIN PARTS ................................................................................................... 10ADJUSTMENT ................................................................................................................................................................. 11NOTES ON SCHEMATIC DIAGRAM .............................................................................................................................. 13TYPE OF TRANSISTER AND LED ................................................................................................................................. 13WAVEFORMS OF CD CIRCUIT ...................................................................................................................................... 14BLOCK DIAGRAM ........................................................................................................................................................... 15SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD .............................................................................................. 18VOLTAGE ........................................................................................................................................................................ 32TROUBLESHOOTING ..................................................................................................................................................... 33FUNCTION TABLE OF IC................................................................................................................................................ 37FL SEGMENT ................................................................................................................................................................... 42PARTS GUIDE/EXPLODED VIEWPACKING OF THE SET (FOR U.S.A. ONLY)
CD-C606 mini component system consisting ofCD-C606 mini component system andCP-C606 speaker system
CD-C1900 mini component system consisting ofCD-C1900 mini component system andCP-C1900 speaker system
Illustration: CD-C606
CD-C606/1900,CP-C606/1900
– 2 –
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFERTO THE OPERATION MANUAL.
CD-C606/1900
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)BEFORE RETURNING THE AUDIO PRODUCT(Fire & Shock Hazard)Before returning the audio product to the user, perform thefollowing safety checks.1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassisand other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,cabinet, terminal board, adjustment and compartmentcovers or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakagecurrent in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15µF capacitor in series with all exposedmetal cabinet parts and a known earth ground, such asconduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,sensitivity to measure the AC voltage drop across theresistor (See diagram).
* Connect the resistor connection to all exposed metal partshaving a return path to the chassis (antenna, metal cabinet,screw heads, knobs and control shafts, escutcheon, etc.)and measure the AC voltage drop across the resistor.
All check must be repeated with the AC line cord plug connectionreversed.Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.AC.) or more is excessive and indicates a potential shockhazard which must be corrected before returning the audioproduct to the owner.
Dimensions: Width; 270 mm (10-5/8")Height; 300 mm (11-13/16")Depth; 353 mm (13-7/8")
Weight: 4.7 kg (10.3 lbs)
Output power: MPO; 36 W (18 W + 18 W)(10% T.H.D.)RMS; 20 W (10 W + 10 W)(10% T.H.D.)
Dimensions: Width; 220 mm (8-11/16")Height; 300 mm (11-13/16")Depth; 180 mm (7-1/16")
Weight:(For Canada) 2.0 kg (4.4 lbs.)/each
(For Canada)
(For U.S.A.)
(For Canada)
(For Canada)
(For Canada)
CP-C606/1900
Specifications for this model are subject to change without priornotice.
CD-C606/1900,CP-C606/1900
– 2 –
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFERTO THE OPERATION MANUAL.
CD-C606/1900
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)BEFORE RETURNING THE AUDIO PRODUCT(Fire & Shock Hazard)Before returning the audio product to the user, perform thefollowing safety checks.1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassisand other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,cabinet, terminal board, adjustment and compartmentcovers or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakagecurrent in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15µF capacitor in series with all exposedmetal cabinet parts and a known earth ground, such asconduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,sensitivity to measure the AC voltage drop across theresistor (See diagram).
* Connect the resistor connection to all exposed metal partshaving a return path to the chassis (antenna, metal cabinet,screw heads, knobs and control shafts, escutcheon, etc.)and measure the AC voltage drop across the resistor.
All check must be repeated with the AC line cord plug connectionreversed.Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.AC.) or more is excessive and indicates a potential shockhazard which must be corrected before returning the audioproduct to the owner.
Dimensions: Width; 270 mm (10-5/8")Height; 300 mm (11-13/16")Depth; 353 mm (13-7/8")
Weight: 4.7 kg (10.3 lbs)
Output power: MPO; 36 W (18 W + 18 W)(10% T.H.D.)RMS; 20 W (10 W + 10 W)(10% T.H.D.)
Dimensions: Width; 220 mm (8-11/16")Height; 300 mm (11-13/16")Depth; 180 mm (7-1/16")
Weight:(For Canada) 2.0 kg (4.4 lbs.)/each
(For Canada)
(For U.S.A.)
(For Canada)
(For Canada)
(For Canada)
CP-C606/1900
Specifications for this model are subject to change without priornotice.
CD-C606/1900,CP-C606/1900
– 3 –
NAMES OF PARTSCD-C606/1900
4. Disc Number Indicator5. Record Indicator6. Sleep Indicator7. Extra Bass Indicator8. Function/CD Track/CD Counter/Frequency/
Preset Channel/Volume/Timer/Sleep TimeIndicator
9. Memory Indicator10. FM Stereo Mode Indicator11. FM Stereo Indicator12. CD Repeat Indicator13. CD Play Indicator14. CD Pause Indicator15. Timer Indicators
16. (TAPE 2) Record Pause Button17. (CD) Track Down/Review Button
(TUNER) Preset Down Button(TAPE 2) Rewind Button
18. (CD) Track Up/Cue Button(TUNER) Preset Up Button(TAPE 2) Fast Foward Button
19. Timer/Sleep Button20. Clock Button21. Power Button22. Function Selector Buttons23. Extra Bass/Demo Button24. Volume Up/Down Buttons25. Memory/Set Button26. (CD/TAPE) Stop Button27. (CD) Play/Repeat Button
(TAPE) Play Button28. Tuning and Time Up/Down Buttons29. Headphone Socket
13. (TAPE 1) Play Button14. (TAPE 1/2) Stop Button15. (TAPE 2) Play Button16. (TAPE 2) Rewind Button17. (TAPE 2) Fast Forward Button18. (TAPE 2) Record Pause Button19. Function Selector Buttons20. Power Button21. Extra Bass Button22. Volume Up/Down Buttons
Speaker
4. Super Tweeter5. Woofer6. Bass Reflex Duct7. Speaker Wire
CD-C606/1900,CP-C606/1900
– 5 –
OPERATION MANUAL
AM
0:0
0A
M 1
2:00
0:00
(Mai
n un
it op
erat
ion)
In th
is e
xam
ple,
the
cloc
k is
set
for
the
12-h
our
(AM
12:
00)
syst
em.
2 3 5 6 7 9PO
WE
R
ME
MO
RY
/S
ET
CLO
CK
TU
NIN
G/
TIM
E(
)
1P
ress
the
PO
WE
R b
utto
n to
ent
er th
e st
and-
by m
ode.
2P
ress
the
CLO
CK
but
ton.
3W
ithin
5 s
econ
ds, p
ress
the
ME
MO
RY
/SE
T b
utto
n.
4P
ress
the
TU
NIN
G/T
IME
(
or
) bu
tton
to s
elec
t th
e tim
edi
spla
y m
ode.
"AM
12:
00"
The
12-
hour
dis
play
will
app
ear.
(AM
12:
00 -
PM
11:
59)
"AM
0:0
0"T
he 1
2-ho
ur d
ispl
ay w
ill a
ppea
r.(A
M 0
:00
- P
M 1
1:59
)"0
:00"
The
24-
hour
dis
play
will
app
ear.
(0:0
0 -
23:5
9)
Not
e th
at th
is c
an o
nly
be s
et w
hen
the
unit
is fi
rst i
nsta
lled
orit
has
been
res
et (
see
page
13)
.5
Pre
ss th
e M
EM
OR
Y/S
ET
but
ton.
6P
ress
the
TU
NIN
G/T
IME
( o
r )
butto
n to
adj
ust t
he h
our.
Pre
ss t
he T
UN
ING
/TIM
E (
or
) bu
tton
once
to
adva
nce
the
time
by 1
hou
r. H
old
it do
wn
to a
dvan
ce c
ontin
uous
ly.
Whe
n th
e 12
-hou
r di
spla
y is
sel
ecte
d, "
AM
" w
ill c
hang
e au
to-
mat
ical
ly to
"P
M".
7P
ress
the
ME
MO
RY
/SE
T b
utto
n.
8P
ress
the
TU
NIN
G/T
IME
( o
r ) b
utto
n to
adj
ust t
he m
inut
es.
Pre
ss t
he T
UN
ING
/TIM
E (
or
) bu
tton
once
to
adva
nce
the
time
by 1
min
ute.
Hol
d it
dow
n to
cha
nge
the
time
in 5
min
ute
inte
rval
s.T
he h
our
setti
ng w
ill n
ot a
dvan
ce e
ven
if m
inut
es a
dvan
cefr
om "
59"
to "
00".
9P
ress
the
ME
MO
RY
/SE
T b
utto
n.
The
clo
ck s
tart
s op
erat
ing
from
"0" s
econ
ds. (
Sec
onds
are
not
disp
laye
d.)
No
te:
In t
he e
vent
of
pow
er f
ailu
re o
r w
hen
the
AC
pow
er c
ord
isdi
scon
nect
ed, t
he c
lock
dis
play
will
go
out.
Whe
n th
e A
C p
ower
sup
ply
is r
esto
red,
the
clo
ck d
ispl
ay w
illfla
sh o
n an
d of
f to
ind
icat
e th
e tim
e w
hen
the
pow
er f
ailu
reoc
curr
ed o
r w
hen
the
AC
pow
er c
ord
was
dis
conn
ecte
d.If
this
hap
pens
, fol
low
the
proc
edur
e be
low
to c
hang
e th
e cl
ock
time.
To c
han
ge
the
clo
ck t
ime:
Pre
ss th
e C
LOC
K b
utto
n.
With
in 5
sec
onds
, pre
ss th
e M
EM
OR
Y/S
ET
but
ton.
Per
form
ste
ps 6
- 9
abo
ve.
To s
ee t
he
tim
e d
isp
lay:
Pre
ss th
e C
LOC
K b
utto
n.
The
tim
e di
spla
y w
ill a
ppea
r fo
r ab
out 5
sec
onds
.
To c
han
ge
the
tim
e d
isp
lay
mo
de:
Per
form
ste
ps 1
- 2
in th
e se
ctio
n "R
ES
ET
TIN
G T
HE
MIC
RO
CO
MP
UT
ER
".P
erfo
rm s
teps
1 -
9 a
bove
.
SE
TT
ING
TH
E C
LO
CK
84
1 2 3 1 2
PR
EP
AR
AT
ION
FO
R U
SE
Rem
ote
co
ntr
ol
No
tes
con
cern
ing
use
:R
epla
ce th
e ba
tterie
s if
the
oper
atin
g di
stan
ce is
red
uced
or
ifth
e op
erat
ion
beco
mes
err
atic
.
Pe
rio
dic
ally
cle
an
th
e t
ran
smit
ter
LE
D o
n t
he
re
mo
teco
ntro
l and
the
sens
or o
n th
e m
ain
unit
with
a s
oft c
loth
.
Exp
osin
g th
e se
nsor
on
the
mai
n un
it to
str
ong
light
may
inte
r-fe
re w
ith o
pera
tion.
Cha
nge
the
light
ing
or th
e di
rect
ion
of th
eun
it.
Kee
p th
e re
mot
e co
ntro
l aw
ay fr
om m
oist
ure,
exc
essi
ve h
eat,
shoc
k, a
nd v
ibra
tions
.
151515
1
8" -
20'
(0.2
m -
6 m
)
RE
SE
TT
ING
TH
E M
ICR
OC
OM
PU
TE
R
Res
et t
he
mic
roco
mp
ute
r u
nd
er t
he
follo
win
g c
on
dit
ion
s:To
era
se a
ll of
the
sto
red
mem
ory
cont
ents
(cl
ock
and
timer
setti
ngs,
and
tune
r an
d C
D p
rese
ts).
If th
e di
spla
y is
not
cor
rect
.
If th
e op
erat
ion
is n
ot c
orre
ct.
1P
ress
the
PO
WE
R b
utto
n to
ent
er th
e st
and-
by m
ode.
2P
ress
and
hol
d do
wn
the
/ b
utto
n an
d th
e /
butto
n, h
old
dow
n th
e P
OW
ER
but
ton
for
at le
ast 1
sec
ond.
Cau
tio
n:
The
ope
ratio
n ex
plai
ned
abov
e w
ill e
rase
all
data
sto
red
inm
emor
y in
clud
ing
cloc
k an
d tim
er s
ettin
gs, a
nd tu
ner
and
CD
pres
et.
1,2
2
CD-C606/1900,CP-C606/1900
– 6 –
QUICK GUIDE
1
VO
LUM
E
VO
LUM
E
1515
LEFT
RIGH
T
SPEA
KERS
RATE
D SP
EAKE
R IM
PEDA
NCE:
8 OH
MS
MIN
.
PO
WE
R
PO
WE
R
X-B
AS
S
X-BA
SS/D
EM
O
1
MIN
I CO
MP
ON
EN
TS
YS
TE
MC
D-C
606
Qu
ick-
Gu
ide
Gu
ía r
ápid
a
Pre
par
atio
n f
or
use
Pre
par
ació
n p
ara
su u
so
A
C 1
20 V
, 60
Hz
12
0 V
de
CA
, 60
Hz
Left
spea
ker
Alta
voz
izqu
ierd
o
A
M L
oop
Ant
enna
A
nten
a de
cua
dro
deA
M
F
M A
nten
na
A
nten
a de
FM
Bla
ck
Neg
ro
Red
Roj
oB
lack
Neg
ro
Red
Roj
o
Turn
ing
th
e p
ow
er o
n a
nd
off
Co
nex
ión
y d
esco
nex
ión
de
la a
limen
taci
ón
Rem
ote
co
ntr
ol
Co
ntr
ol r
emo
toR
emot
e S
enso
r
Sen
sor
rem
ote
2
“AA
” ba
tterie
s
D
os p
ilas
“AA
”
8" -
20
' (0.
2m -
6m
)
0,2m
- 6
m
B
atte
ries
are
not
incl
uded
.
La
s pi
las
no e
stán
incl
uida
s.
So
un
d c
on
tro
lC
on
tro
l del
so
nid
o
V
olum
e
Vo
lum
en
E
xtra
-BA
SS
G
rave
s ex
tra
Rig
ht s
peak
er
Alta
voz
dere
cho
ST
FM
ST
ER
OF
M M
ON
OA
M
TA
PE
1T
AP
E 2
TA
PE
2
REC
PAUS
E
OPE
N/C
LOSE
OPE
N/C
LOSE
TU
NIN
G/T
IME
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
Tap
e p
layb
ack
Rep
rod
ucc
ión
de
cin
tas
Rec
ord
ing
fro
m C
Ds
Gra
bac
ión
de
dis
cos
com
pac
tos
L
oa
d t
he
dis
c to
be
reco
rded
.
In
trod
uzca
el d
isco
que
va a
gra
bar.
C
D r
ecor
ding
sta
rts.
La
gra
baci
ón d
e C
Dem
piez
a.
Rad
io o
per
atio
nF
un
cio
nam
ien
to d
e la
rad
io
T
he
so
un
d l
eve
l a
t a
giv
en
vo
lum
e s
ett
ing
depe
nds
on a
com
bina
tion
of s
peak
er e
ffici
ency
,lo
catio
n an
d m
any
othe
r fa
ctor
s. I
t is
adv
isab
leto
avo
id e
xpos
ure
to h
igh
volu
me
leve
ls,
whi
choc
cur
whi
le t
urni
ng t
he u
nit
on w
ith t
he v
olum
eco
ntr
ol
sett
ing
up
hig
h,
or
wh
ile c
on
tinu
ally
liste
ning
at h
igh
volu
me
leve
ls.
O
nly
disc
s be
arin
g th
e lo
go a
s sh
own
can
bepl
ayed
in th
is u
nit.
Pre
cau
tio
nP
reca
uci
ón
E
l niv
el d
e so
nido
en
una
posi
ción
de
volu
men
fija
do
de
pe
nd
e d
e u
na
co
mb
ina
ció
n d
el
rend
imie
nto
de l
as a
ltavo
ces,
la
posi
ción
ym
ucho
s ot
ros
fact
ores
. Es
acon
seja
ble
evita
r un
aum
ento
de
volu
men
. E
sto
se p
rodu
ce,
por
ejem
plo,
al c
onec
tar
el a
para
to c
on e
l vol
umen
pues
to e
n un
a po
sici
ón a
lta. E
vite
con
tinua
r la
audi
ción
pro
long
ada
a al
tos
nive
les
de s
onid
o.
En
este
apa
rato
sól
o pu
eden
rep
rodu
cirs
e lo
sdi
scos
que
teng
an e
l log
otip
o m
ostra
do.
La
bel f
acin
g up
E
tique
ta h
acia
arr
iba
CD
pla
ybac
kR
epro
du
cció
n d
e d
isco
s co
mp
acto
s
CD-C606/1900,CP-C606/1900
– 7 –
1
VO
LUM
E
VO
LUM
E
1515
LEFT
RIGH
T
SPEA
KERS
RATE
D SP
EAKE
R IM
PEDA
NCE:
8 OH
MS
MIN
.
PO
WE
R
PO
WE
R
X-B
AS
S
X-BA
SS/D
EM
O
1
MIN
I CO
MP
ON
EN
TS
YS
TE
MC
D-C
1900
Qu
ick-
Gu
ide
Gu
ía r
ápid
a
Pre
par
atio
n f
or
use
Pre
par
ació
n p
ara
su u
so
A
C 1
20 V
, 60
Hz
12
0 V
de
CA
, 60
Hz
Left
spea
ker
Alta
voz
izqu
ierd
o
A
M L
oop
Ant
enna
A
nten
a de
cua
dro
deA
M
F
M A
nten
na
A
nten
a de
FM
Bla
ck
Neg
ro
Red
Roj
oB
lack
Neg
ro
Red
Roj
o
Turn
ing
th
e p
ower
on
an
d o
ffC
on
exió
n y
des
con
exió
n d
e la
alim
enta
ció
n
Rem
ote
co
ntr
ol
Co
ntr
ol r
emo
toR
emot
e S
enso
r
Sen
sor
rem
ote
2
“AA
” ba
tterie
s
D
os p
ilas
“AA
”
8" -
20
' (0.
2m -
6m
)
0,2m
- 6
m
B
atte
ries
are
not
incl
uded
.
La
s pi
las
no e
stán
incl
uida
s.
So
un
d c
on
tro
lC
on
tro
l del
so
nid
o
V
olum
e
Vo
lum
en
E
xtra
-BA
SS
G
rave
s ex
tra
Rig
ht s
peak
er
Alta
voz
dere
cho
ST
FM
ST
ER
OF
M M
ON
OA
M
TA
PE
1T
AP
E 2
TA
PE
2
REC
PAUS
E
OPE
N/C
LOSE
OPE
N/C
LOSE
TU
NIN
G/T
IME
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
Tap
e p
layb
ack
Rep
rod
ucc
ión
de
cin
tas
Rec
ord
ing
fro
m C
Ds
Gra
bac
ión
de
dis
cos
com
pac
tos
L
oa
d t
he
dis
c to
be
reco
rded
.
In
trod
uzca
el d
isco
que
va a
gra
bar.
C
D r
ecor
ding
sta
rts.
La
gra
baci
ón d
e C
Dem
piez
a.
Rad
io o
per
atio
nF
un
cio
nam
ien
to d
e la
rad
io
T
he
so
un
d l
eve
l a
t a
giv
en
vo
lum
e s
ett
ing
depe
nds
on a
com
bina
tion
of s
peak
er e
ffici
ency
,lo
catio
n an
d m
any
othe
r fa
ctor
s. I
t is
adv
isab
leto
avo
id e
xpos
ure
to h
igh
volu
me
leve
ls,
whi
choc
cur
whi
le t
urni
ng t
he u
nit
on w
ith t
he v
olum
eco
ntr
ol
sett
ing
up
hig
h,
or
wh
ile c
on
tinu
ally
liste
ning
at h
igh
volu
me
leve
ls.
O
nly
disc
s be
arin
g th
e lo
go a
s sh
own
can
bepl
ayed
in th
is u
nit.
Pre
cau
tio
nP
reca
uci
ón
E
l niv
el d
e so
nido
en
una
posi
ción
de
volu
men
fija
do
de
pe
nd
e d
e u
na
co
mb
ina
ció
n d
el
rend
imie
nto
de l
as a
ltavo
ces,
la
posi
ción
ym
ucho
s ot
ros
fact
ores
. Es
acon
seja
ble
evita
r un
aum
ento
de
volu
men
. E
sto
se p
rodu
ce,
por
ejem
plo,
al c
onec
tar
el a
para
to c
on e
l vol
umen
pues
to e
n un
a po
sici
ón a
lta. E
vite
con
tinua
r la
audi
ción
pro
long
ada
a al
tos
nive
les
de s
onid
o.
En
este
apa
rato
sól
o pu
eden
rep
rodu
cirs
e lo
sdi
scos
que
teng
an e
l log
otip
o m
ostra
do.
La
bel f
acin
g up
E
tique
ta h
acia
arr
iba
CD
pla
ybac
kR
epro
du
cció
n d
e d
isco
s co
mp
acto
s
CD-C606/1900,CP-C606/1900
– 6 –
QUICK GUIDE
1
VO
LUM
E
VO
LUM
E
1515
LEFT
RIGH
T
SPEA
KERS
RATE
D SP
EAKE
R IM
PEDA
NCE:
8 OH
MS
MIN
.
PO
WE
R
PO
WE
R
X-B
AS
S
X-BA
SS/D
EM
O
1
MIN
I CO
MP
ON
EN
TS
YS
TE
MC
D-C
606
Qu
ick-
Gu
ide
Gu
ía r
ápid
a
Pre
par
atio
n f
or
use
Pre
par
ació
n p
ara
su u
so
A
C 1
20 V
, 60
Hz
12
0 V
de
CA
, 60
Hz
Left
spea
ker
Alta
voz
izqu
ierd
o
A
M L
oop
Ant
enna
A
nten
a de
cua
dro
deA
M
F
M A
nten
na
A
nten
a de
FM
Bla
ck
Neg
ro
Red
Roj
oB
lack
Neg
ro
Red
Roj
o
Turn
ing
th
e p
ow
er o
n a
nd
off
Co
nex
ión
y d
esco
nex
ión
de
la a
limen
taci
ón
Rem
ote
co
ntr
ol
Co
ntr
ol r
emo
toR
emot
e S
enso
r
Sen
sor
rem
ote
2
“AA
” ba
tterie
s
D
os p
ilas
“AA
”
8" -
20
' (0.
2m -
6m
)
0,2m
- 6
m
B
atte
ries
are
not
incl
uded
.
La
s pi
las
no e
stán
incl
uida
s.
So
un
d c
on
tro
lC
on
tro
l del
so
nid
o
V
olum
e
Vo
lum
en
E
xtra
-BA
SS
G
rave
s ex
tra
Rig
ht s
peak
er
Alta
voz
dere
cho
ST
FM
ST
ER
OF
M M
ON
OA
M
TA
PE
1T
AP
E 2
TA
PE
2
REC
PAUS
E
OPE
N/C
LOSE
OPE
N/C
LOSE
TU
NIN
G/T
IME
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
Tap
e p
layb
ack
Rep
rod
ucc
ión
de
cin
tas
Rec
ord
ing
fro
m C
Ds
Gra
bac
ión
de
dis
cos
com
pac
tos
L
oa
d t
he
dis
c to
be
reco
rded
.
In
trod
uzca
el d
isco
que
va a
gra
bar.
C
D r
ecor
ding
sta
rts.
La
gra
baci
ón d
e C
Dem
piez
a.
Rad
io o
per
atio
nF
un
cio
nam
ien
to d
e la
rad
io
T
he
so
un
d l
eve
l a
t a
giv
en
vo
lum
e s
ett
ing
depe
nds
on a
com
bina
tion
of s
peak
er e
ffici
ency
,lo
catio
n an
d m
any
othe
r fa
ctor
s. I
t is
adv
isab
leto
avo
id e
xpos
ure
to h
igh
volu
me
leve
ls,
whi
choc
cur
whi
le t
urni
ng t
he u
nit
on w
ith t
he v
olum
eco
ntr
ol
sett
ing
up
hig
h,
or
wh
ile c
on
tinu
ally
liste
ning
at h
igh
volu
me
leve
ls.
O
nly
disc
s be
arin
g th
e lo
go a
s sh
own
can
bepl
ayed
in th
is u
nit.
Pre
cau
tio
nP
reca
uci
ón
E
l niv
el d
e so
nido
en
una
posi
ción
de
volu
men
fija
do
de
pe
nd
e d
e u
na
co
mb
ina
ció
n d
el
rend
imie
nto
de l
as a
ltavo
ces,
la
posi
ción
ym
ucho
s ot
ros
fact
ores
. Es
acon
seja
ble
evita
r un
aum
ento
de
volu
men
. E
sto
se p
rodu
ce,
por
ejem
plo,
al c
onec
tar
el a
para
to c
on e
l vol
umen
pues
to e
n un
a po
sici
ón a
lta. E
vite
con
tinua
r la
audi
ción
pro
long
ada
a al
tos
nive
les
de s
onid
o.
En
este
apa
rato
sól
o pu
eden
rep
rodu
cirs
e lo
sdi
scos
que
teng
an e
l log
otip
o m
ostra
do.
La
bel f
acin
g up
E
tique
ta h
acia
arr
iba
CD
pla
ybac
kR
epro
du
cció
n d
e d
isco
s co
mp
acto
s
CD-C606/1900,CP-C606/1900
– 7 –
1
VO
LUM
E
VO
LUM
E
1515
LEFT
RIGH
T
SPEA
KERS
RATE
D SP
EAKE
R IM
PEDA
NCE:
8 OH
MS
MIN
.
PO
WE
R
PO
WE
R
X-B
AS
S
X-BA
SS/D
EM
O
1
MIN
I CO
MP
ON
EN
TS
YS
TE
MC
D-C
1900
Qu
ick-
Gu
ide
Gu
ía r
ápid
a
Pre
par
atio
n f
or
use
Pre
par
ació
n p
ara
su u
so
A
C 1
20 V
, 60
Hz
12
0 V
de
CA
, 60
Hz
Left
spea
ker
Alta
voz
izqu
ierd
o
A
M L
oop
Ant
enna
A
nten
a de
cua
dro
deA
M
F
M A
nten
na
A
nten
a de
FM
Bla
ck
Neg
ro
Red
Roj
oB
lack
Neg
ro
Red
Roj
o
Turn
ing
th
e p
ower
on
an
d o
ffC
on
exió
n y
des
con
exió
n d
e la
alim
enta
ció
n
Rem
ote
co
ntr
ol
Co
ntr
ol r
emo
toR
emot
e S
enso
r
Sen
sor
rem
ote
2
“AA
” ba
tterie
s
D
os p
ilas
“AA
”
8" -
20
' (0.
2m -
6m
)
0,2m
- 6
m
B
atte
ries
are
not
incl
uded
.
La
s pi
las
no e
stán
incl
uida
s.
So
un
d c
on
tro
lC
on
tro
l del
so
nid
o
V
olum
e
Vo
lum
en
E
xtra
-BA
SS
G
rave
s ex
tra
Rig
ht s
peak
er
Alta
voz
dere
cho
ST
FM
ST
ER
OF
M M
ON
OA
M
TA
PE
1T
AP
E 2
TA
PE
2
REC
PAUS
E
OPE
N/C
LOSE
OPE
N/C
LOSE
TU
NIN
G/T
IME
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
TAPE
(1 2)
C D
TUNER (BAND)
Tap
e p
layb
ack
Rep
rod
ucc
ión
de
cin
tas
Rec
ord
ing
fro
m C
Ds
Gra
bac
ión
de
dis
cos
com
pac
tos
L
oa
d t
he
dis
c to
be
reco
rded
.
In
trod
uzca
el d
isco
que
va a
gra
bar.
C
D r
ecor
ding
sta
rts.
La
gra
baci
ón d
e C
Dem
piez
a.
Rad
io o
per
atio
nF
un
cio
nam
ien
to d
e la
rad
io
T
he
so
un
d l
eve
l a
t a
giv
en
vo
lum
e s
ett
ing
depe
nds
on a
com
bina
tion
of s
peak
er e
ffici
ency
,lo
catio
n an
d m
any
othe
r fa
ctor
s. I
t is
adv
isab
leto
avo
id e
xpos
ure
to h
igh
volu
me
leve
ls,
whi
choc
cur
whi
le t
urni
ng t
he u
nit
on w
ith t
he v
olum
eco
ntr
ol
sett
ing
up
hig
h,
or
wh
ile c
on
tinu
ally
liste
ning
at h
igh
volu
me
leve
ls.
O
nly
disc
s be
arin
g th
e lo
go a
s sh
own
can
bepl
ayed
in th
is u
nit.
Pre
cau
tio
nP
reca
uci
ón
E
l niv
el d
e so
nido
en
una
posi
ción
de
volu
men
fija
do
de
pe
nd
e d
e u
na
co
mb
ina
ció
n d
el
rend
imie
nto
de l
as a
ltavo
ces,
la
posi
ción
ym
ucho
s ot
ros
fact
ores
. Es
acon
seja
ble
evita
r un
aum
ento
de
volu
men
. E
sto
se p
rodu
ce,
por
ejem
plo,
al c
onec
tar
el a
para
to c
on e
l vol
umen
pues
to e
n un
a po
sici
ón a
lta. E
vite
con
tinua
r la
audi
ción
pro
long
ada
a al
tos
nive
les
de s
onid
o.
En
este
apa
rato
sól
o pu
eden
rep
rodu
cirs
e lo
sdi
scos
que
teng
an e
l log
otip
o m
ostra
do.
La
bel f
acin
g up
E
tique
ta h
acia
arr
iba
CD
pla
ybac
kR
epro
du
cció
n d
e d
isco
s co
mp
acto
s
CD-C606/1900,CP-C606/1900
– 10 –
How to remove the turntable up/down/loadingmotor (See Fig. 10-3)1. Remove the screws (A1) x 2 pcs., to remove the turntable
up/down/loading motor.
How to remove the pickup (See Fig. 10-4)1. Remove the screws (B1) x 2 pcs., to remove the shaft (B2)
x 1 pc.2. Remove the stop washer (B3) x 1 pc., to remove the gear
(B4) x 1 pc.3. Remove the pickup.
Figure 10-4
REMOVING AND REINSTALLING THE MAIN PARTS
CD MECHANISM SECTIONPerform steps 1, 2, 3, and 8 ~ 12 of the disassembly methodto remove the CD mechanism.
Figure 10-3
Note :After disconnecting the optical pickup connector wrap thefront end of connector in conductive aluminum foil so as toprevent damage to the optical pickup by static electricity.
IF 10.7 MHz 98.00 MHz T302(Turn Input: Pin 1 ofthe core of IC301transformer Output: TP302T381 fullycounter-clookwise.)
InstrumentConnection
TestStage
AdjustingParts
FrequencyDisplay
Frequency
AdjustingParts
InstrumentConnection
FrequencyDisplay
Frequency
• VCO Frequency
* Adjust for 76 kHz ± 200 Hz.
Notes:After preparing the test circuit shown in Fig 11-3, connect thePin 13 , Pin 21 and ground of the IC303 with test circuit, andmeasure the Value.At this time, apply a standard unmodulated signal input andadjust the VCO.
Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessaryto readjust it.Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted.
CD SECTION
Figure 12-1
Note:
Only in STOP state it is possible to slide the pickup with the ( ) or ( ) key.VOL. --- Last memoryBAL. --- CENTERR.GEQ. --- FLATX-BAS --- OFF
Canceling method - POWER OFF
• Setting the test modeAny one of test mode can be set by pressing several keys as follows.<REC. PAUSE> + <DISC. SKIP> + <POWER> TEST: CD operation test• TEST modeFunction — CD test mode
Setting of TEST mode
Indication of CD TST mode (Fig. 12-1)
OPEN/CLOSE operation is manual operation.
The pickup can be moved by using the ( ) or ( ) key.
<MEMORY>LASER ON
<PLAY> key input Press <STOP> key. StopTOC. IL is performed, and the ordinary PLAY is performed.If the following key is pressed during PLAY, it is possibleto specify directly any Track No.<Disc Number 1> key: Track 4<Disc Number 2> key: Track 9<Disc Number 3> key: Track 15
<MEMORY>Tracking on the spot.SERVO OFF PLAY
<MEMORY>Tracking on the spot.SERVO ON PLAY
STOP
IL is not performed.
<STOP>
1 2 3
Figure 12-2
Figure 12-3 Figure 12-4
• Automatic adjustment item1. Focus offset (Fig. 12-2)2. Tracking offset (Fig. 12-3)3. E/F balance (tracking error balance) (Fig. 12-4)4. RF level AGC function (HF level: constant)5. RF level automatic follow-up of the tracking gain
This automatic adjustment is performed each time a disc ischanged. Therefore, each disc is played back using theoptimal settings.
2
0.1s0.50 VIC1 20 FE
0.1s0.50 VIC1 7 TE
1
FOCUSOFF-SETADJUST
TRACKINGOFF-SETADJUST
2
1
10ms0.50 VIC1 20 FE
10ms0.50 VIC1 7 TE
EnlargedView
TRACKINGOFF-SETADJUST
2
1TO
TE
200 ms1V/diVIC 1 15
200 ms1V/diVIC 1 7
TRACKING/ERRORBARANCEADJUST
CD-C606/1900,CP-C606/1900
– 13 –
SW1 OPEN/CLOSE ON—OFF
SW2 MECHA UP ON—OFF
SW3 DISC NUMBER ON—OFF
SW4 PICKUP IN ON—OFF
SW605 TAPE 1 MAIN ON—OFF
SW606 TAPE 2 MAIN ON—OFF
SW607 TAPE 1 RECORD ON—OFF
SW608 TAPE 1 PLAY ON—OFF
SW701 POWER ON—OFF
SW702 VOLUME UP ON—OFF
SW703 VOLUME DOWN ON—OFF
SW704 PLAY ON—OFF
• The indicated voltage in each section is the one measuredby Digital Multimeter between such a section and the chas-sis with no signal given.1. In the tuner section,
( ) indicates AM< > indicates FM stereo
2. In the main section, a tape is being played back.3. In the deck section, a tape is being played back.
( ) indicates the record state.4. In the power section, a tape is being played back.5. In the CD section, the CD is stopped.
• Parts marked with “ ” ( ) are important formaintaining the safety of the set. Be sure to replace theseparts with specified ones for maintaining the safety andperformance of the set.
NOTES ON SCHEMATIC DIAGRAM• Resistor:
To differentiate the units of resistors, such symbol as K andM are used: the symbol K means 1000 ohm and the symbolM means 1000 kohm and the resistor without any symbol isohm-type resistor. Besides, the one with “Fusible” is a fusetype.
• Capacitor:To indicate the unit of capacitor, a symbol P is used: thissymbol P means micro-micro-farad and the unit of thecapacitor without such a symbol is microfarad. As toelectrolytic capacitor, the expression “capacitance/withstandvoltage” is used.(CH), (TH), (RH), (UJ): Temperature compensation(ML): Mylar type(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for thismodel are subject to change for improvement without priornotice.
• The indicated voltage in each section is the one measuredby Digital Multimeter between such a section and the chas-sis with no signal given.1. In the tuner section,
( ) indicates AM< > indicates FM stereo
2. In the main section, a tape is being played back.3. In the deck section, a tape is being played back.
( ) indicates the record state.4. In the power section, a tape is being played back.5. In the CD section, the CD is stopped.
• Parts marked with “ ” ( ) are important formaintaining the safety of the set. Be sure to replace theseparts with specified ones for maintaining the safety andperformance of the set.
NOTES ON SCHEMATIC DIAGRAM• Resistor:
To differentiate the units of resistors, such symbol as K andM are used: the symbol K means 1000 ohm and the symbolM means 1000 kohm and the resistor without any symbol isohm-type resistor. Besides, the one with “Fusible” is a fusetype.
• Capacitor:To indicate the unit of capacitor, a symbol P is used: thissymbol P means micro-micro-farad and the unit of thecapacitor without such a symbol is microfarad. As toelectrolytic capacitor, the expression “capacitance/withstandvoltage” is used.(CH), (TH), (RH), (UJ): Temperature compensation(ML): Mylar type(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for thismodel are subject to change for improvement without priornotice.
Is from 5 V till 2.5V down pulse (approx. 300 ms) Check the SW2 and the wiring from the IC701 pin 41 to theSW2.
No
input into the IC701 pin 41 when the turntable is rotating?
5V
2.5V
Yes
Check IC2 pin26 Q51 and the periphery.
Check the MECHA UP switch and the wiring from the IC701pin 41 to the MECHA UP switch.No
Yes
Is there following voltage input on the IC701 pin 41 in thespecific state?When the CD mechanism is moved up: 0VIn other states: 4.3V
Yes
IC701 defective.
When the CD does not functionWhen the CD section does not operate. When the objective lens of the optical pickup is dirty, this section may not operate. Cleanthe objective lens, and check the playback operation. When this section does not operate even after the above step is taken, checkthe following items.Remove the cabinet and follow the troubleshooting instructions."Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickuplens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off.Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.Do not touch the lens with the bare hand.
Dust gradually accumulates on the objective lens during use, and it may degrade performance. To avoid this problem, use acleaning disc designed for CD optical pickup lenses.
0V
HOW TO USE1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has
the mark next to it.2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button.3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stopbutton.CAUTION
The CD lens cleaner should be effective for 30~50 operations, however if the brushes become worn out earller then pleasereplace the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and /or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD players or on computer CD ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting this product is prohibited by law.
Is there following voltage input in specific state of IC701 pin 39? Open state: 0V Close state: 0V Intermediate state between open state and close state: 4.3V
Is H output to IC2 pin 24 or 25 for 7 seconds when the OPEN/CLOSE button is pressed? IC3 is defective. Replace it.
Is 4V output between IC3 pins 38 and 39 during operationstated above?
Check the loading motor (M3) and the loading mechanism.
Yes
Yes
Yes
No
No
IC2 defective.
NoCheck the periphery of IC3.
IC3 defective.
OK
OK
Check the OPEN/CLOSE switch and the wiring from theIC701 pin 39 to the OPEN/CLOSE switch.
Check the wiring of the IC2 pins 24 and 25, IC3 pins 38 and 39.
• The CD function will not work.
The CD operating buttons don't work.
Check the CD, DSP, power supply, and 16.93 MHz clock, andreset terminal.
Check the waveform of SCK, SO (DATA) and SI (COMM).
Yes
Yes
See if the pick-up in the PICKUP IN switch position.
If the items mentioned above are OK, check the mainmicrocomputer IC701.
Yes
Yes
No
Is there following voltage input on the IC701 pin 41 in thespecific state?
In other states: 4.3VWhen the CD mechanism is moved up: 0V
• When turntable fails to move.
Check the MECHA UP switch and the wiring from the IC701pin 41 to the MECHA UP switch.
Is 4V output from the Q51 emitter during operation statedabove?
Yes
Yes
Check the wiring of IC2 pin 27 and Q51 pin 2.
OKNo
No
Is L output from the IC2 pin 27 during SEC when the disc skipswitch is pressed?
Yes
Check turntable motor and turntable mechanism.
Check Q51 and the periphery.
IC2 defective.
CD-C606/1900,CP-C606/1900
– 35 –
• Playback can only be performed when a disc isloaded.
Is HF waveform normal (see the Fig. 35-2, Fig. 35-3)?
Check the tracking system.
Is the Focus servo active? (Can you hear it working?) Check the laser diode driver.Check the area around IC1(16) - (21) (focus servo circuit).No
Yes
Yes
Yes
Does the DRF signal change from "L" to "H"?No Yes
If the disc is not turning, the DRFshould not change to "H".
Level is abnormal.No Yes
Waveform is unstable. Check the spin system.Yes
Check the peripheryof IC1 pins 41 and 42.
Check the spin system.
Figure 35-3Figure 35-2
HF1.0V/DIV0.5µsec/DIV(DC)(When playing back the disc)
3
21
4
0.5s1.00 VIC1 16 FD
0.5s10.0 VIC2 12 CLV+
0.5s10.0 VIC1 54 DRF
0.5s2.00 VIC1 7 TE
Waveform incase of normalplayback
No
Yes
No
• The CD operating keys work.
Check the Focus - HF system.
Playback can be performed without a disc.
Focus search OKDoes the pick-up move up and down twice?
Does the output waveform of IC1(16)(FD) match that shown inFig. 35-1?
Check the IC1(50)(CLK) line, 4MHz.Check the microcomputer data on pins (51)(CL), (52)(DAT)and (53)CE.
Check the area around IC3-CNP2.Yes
Yes
Figure 35-1
0.5s0.50 VIC1 16 FD
2
1
0.5s0.50 VIC1 7 TE
Focus search is performed two times when play operation is done without disc.
CD-C606/1900,CP-C606/1900
– 36 –
• Checking the spin system.
Yes
No
Play operation is performed without disc.
The turntable rotates a little.
The turntable fails to rotate or rotates at high speed.
YesThe spin driver circuit is normal.
Check the periphery of IC1 pins 23 to 27, pin 39, and pin 40, IC2pin 12 and pin 13, IC3 to CNP3.Yes
• Checking the VCO-PLL system
Figure 36-2
Play operation is performed when disc exits.
Yes
Although HF waveform is normal, TOC data cannot be read.Yes
Check PDO waveform (Fig. 36-2).
Abnormal
Check the IC1 pins 43 and 44, IC2 pins 3, 5, 7, 10, and 11.
• Although HF waveform is normal and the timeindication is normal, no sound is emitted.
Check IC2 pin 48 (EFLG).
Check IC2 pins 37, 40.
Check IC401 and POWER AMP. IC601.
Abnomal
Yes
Usually, the number of pulses of flawless disc is 100 pulses/secor less.No
2
3
0.5s1.00 VIC2 3 PDO
0.5s1.00 VIC1 16 FD
As VCO frequencyis locked at 4.32 MHz, voltage of PDO rises andstabilizes.
Stop --> Play
• Check the tracking system.
Check waveform of IC1 pin 7 (TE).
Play is possible inTEST mode.
Although IL is possible,play is impossible.
Check the peripheryof IC 1 pin 14.
Normal jump is impeded,and the program topcannot be reached.
Check the periphery of IC 1pin 8 to pin 15, and IC 5 toCNP2.
The waveform shown in Fig.36-1 appears, and no-discstate appears soon.
Tracking servo isinoperative.
Yes YesYes
YesYes
Data cannot be read. Check the VCO-PLL system.Yes
Figure 36-1
3
4
5ms1.00 VIC1 7 TE
5 ms5.0 VIC1 54 DRF
CD-C606/1900,CP-C606/1900
– 37 –
IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (1/2)
1 FIN2 Connection pin for photodiode of pickup.RF signal is generated through addition with FIN pin, and FE signal is generated through subtraction.
2 FIN1 Connection pin for photodiode of pickup.
3 E Connection pin for photodiode of pickup. TE signal is generated through subtraction with F pin.
4 F Connection pin for photodiode of pickup.
5 TB Pin for input of DC component of TE signal.
6 TE- Pin to connect gain setting resistor of TE signal to TE signal.
7 TE TE signal output pin.
8 TESI TES (Track error sense) comparator input pin. TE signal is band-passed and input.
9 SCI Input pin for shock detection.
10 TH Pin to set time constant of tracking gain.
11* N.C. No connect.
12 TD- Pin to compose tracking phase compensation constant between TD and VR pins.
13 TD Pin to set tracking phase compensation.
14 JP Pin to set amplitude of tracking jump signal (kick pulse).
15 TO Tracking control signal output pin.
16 FD Focusing control signal output pin.
17 FD- Pin to compose focusing phase compensation constant between FD and FA pins.
18 FA Pin to compose focusing phase compensation constant between FD-/FA-pins.
19 FA- Pin to compose focusing phase compensation constant between FA and FE pins.
20 FE Output pin of FE signal.
21 FE- Pin to connect gain setting resistor of FE signal across TE pin.
22 AGND GND for analog signal.
23 SP Single end output for CV+ and CV- pin input.
24 SPI Spindle amplifier input.
25 SPG Pin to connect gain setting resistor in the 12cm mode of spindle.
26 SP- Pin to connect spindle phase compensation constant together with SPD pin.
27 SPO Spindle control signal output pin.
28 SLEO Pin to connect thread phase compensation constant.
29 SLD Thread control signal output pin.
30 SL- Input pin of thread feed signal from microcomputer.
31 SL+ Input pin of thread feed signal from microcomputer.
32 JP- Input pin of tracking jump signal from DSP.
33 JP+ Input pin of tracking jump signal from DSP.
34 TGL Input pin of tracking gain control signal from DSP. TGL = Gain low at "H"
35 TOFF Input pin of tracking off control signal from DSP. TOFF = Off at "H"
36 TES Output pin of TES signal to DSP.
37 HFL (HIGH FREQUENCY LEVEL) is used to judge whether main beam is positioned on the bit or on the mirror.
38 SLOF Thread servo off control input pin.
39 CV- Pin to input CLV error signal from DSP.
40 CV+ Pin to input CLV error signal from DSP.
41 RFSM RF output pin.
42 RFS- Pin to set gain of RF and set 3T compensation constant together with RFSM pin.
43 SLC (SLICE LEVEL CONTROL) is the output pin to control of the level of the data slice with RF waveform DSP.
44 SLI Input pin to control the level of data slice with DSP.
45 DGND GND pin in the digital system.
46 FSC Output pin for focus search smoothening capacitor.
47 TBC (Tracking Balance Control) Pin to set EF balance variable range.
48* NC No connect.
Pin No. Port Name Function
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
FUNCTION TABLE OF IC
CD-C606/1900,CP-C606/1900
– 38 –
IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (2/2)
Pin No. Port Name Function
49 DEF Defect detection output pin of disc.
50 CLK Reference clock input pin. 4.23MHz of DSP is input.
51 CL Microcomputer command clock input pin.
52 DAT Microcomputer command data input pin.
53 CE Microcomputer command chip enable input pin.
54 DRF (DETECT RF) RF level detection output.
55 FSS (Focus Serch Select) Pin to switch focus search mode. (± search/+ search for reference voltage)
56 VCC2 VCC pin for servo system and digital system.
57 REF1 Pin to connect pass control for reference voltage.
58 VR Reference voltage output pin.
59 LF2 Pin to set defect detection time constant of disc.
60 PHI Pin to connect capacitor for peak hold of RF signal.
61 BHI Pin to connect capacitor for bottom hold of RF signal.
18 TGL Output Output terminal for switch of tracking gain "L" increases the gain.
19 JP+ Output Output for track jump control. 3 values can be output with the commands.
20 JP- Output Output for track jump control. 3 values can be output with the commands.
21* PCK (NC) Output Clock monitor terminal for EFM data replay. 4,3218MHz as the phase clock.
22* FSEQ (NC) Output Output terminal synchronous signal detection. "H" is output when synchronous signal detectedby EFM signal matches synchronous signal internally generated.
23 VDD — Power terminal of digital system.
24 CONT1 Input/Output General purpose input/output terminal 1
25 CONT2 Input/Output General purpose input/output terminal 2
26 CONT3 Input/Output General purpose input/output terminal 3
27 CONT4 Input/Output General purpose input/output terminal 4
28 CONT5 Input/Output General purpose input/output terminal 5
29* EMPH (NC) Output Difference monitor terminal At "H", deemphasis disk is being replayed.
30* C2F (NC) Output C2 flag output terminal.
31* DOUT (NC) Output Output terminal of digital OUTPUT. (EIAJ format)
32* TEST3 (NC) Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
33 TEST4 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
34 PCCL Input CD general-use port control signal.
35* MUTEL (NC) Output L channel 1 bit DAC Mute output terminal for L channel.
36 LVDD — L channel 1 bit DAC Power terminal for L channel.
37 LCHO Output L channel 1 bit DAC L channel output terminal.
38 LVSS — L channel 1 bit DAC Ground terminal for L channel. Surely connected to 0V.
39 RVSS — R channel 1 bit DAC Ground terminal for R channel. Surely connected to 0V.
40 RCHO Output R channel 1 bit DAC R channel output terminal.
41 RVDD — R channel 1 bit DAC Power terminal for R channel.
42* MUTER (NC) Output R channel 1 bit DAC Mute output terminal for R channel.
43 XVDD — Power terminal for quartz oscillation.
44 XOUT Output Ground terminal of 16.9344 MHz quartz oscillator.
45 XIN Input Ground terminal of 16.9344 MHz quartz oscillator.
46 XVSS — Ground terminal for quartz oscillation. Surely connected to 0V.
47* SBSY (NC) Output Output terminal of synchronous signal of subcode block.
48* EFLG (NC) Output Correction monitor terminal of C1, C2, single and double.
49* PW (NC) Output Output terminal of subcodes P, A, R, S, T, U and W.
IC2 VHiLC78622N-1: Servo/Signal Control (LC78622N) (1/2)
Pin No. FunctionTerminal Name Input/Output
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
Controlled with serial data commandfrom microcomputer.When not used, set it as the input terminal andopen it by connecting to 0V, or set it as the outputterminal and open it.
CD-C606/1900,CP-C606/1900
– 40 –
IC2 VHiLC78622N-1: Servo/Signal Control (LC78622N) (2/2)
FunctionTerminal Name Input/Output
50* SFSY (NC) Output Output terminal of synchronous signal of subcode frame. It drops when subcode stands by.
51 SBCK Input Clock input terminal to read subcode. Schmit input (Connected to 0V when not used.)
52* FSX (NC) Output Output terminal of synchronous signal of 7.35kHz divided from quartz oscillation.
53 WRQ Output Output terminal to stand by output of subcode Q.
54 RWC Input Input terminal of read/write. Schmit input.
55 SQOUT Output Output terminal of subcode Q.
56 COIN Input Command input terminal from microcomputer.
57 /CQCK Input Clock input terminal to fetch command input, or pick up subcode from SQOUT. Schmit input.
58 /RES Input Reset input terminal of LC78622. When turning on power, set it at "L".
59* TEST11 (NC) Output Output terminal for test. Used in the open state ("L" output as ordinary).
60* 16M (NC) Output Output terminal of 16.9344Hz.
61 4M Output Output terminal of 4.2336MHz.
62 TEST5 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
63 /CS Input Chip selection input terminal. Pull-down resistor is integrated.Connected to 0when not controlled.
64 TEST1 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
Pin No.
Note: The same potential must be supplied to the power terminals (VDD, VVDD, LVDD, RVDD, XVDD).In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
1 P94/FIP6 7G Output FL Display segment driver
2 P93/FIP5 8G Output FL Display segment driver
3 P92/FIP4 1G Output FL Display segment driver
4 P91/FIP3 2G Output FL Display segment driver
5 P90/FIP2 3G Output FL Display segment driver
6 P81/FIP1 4G Output FL Display segment driver
7 P80/FIP0 9G Output FL Display segment driver
8 VDD VDD — VDD
9 P27/SCK0 DO Input Data input
10 P26/S00/SB1 DI Output Data output
11 P25/SI0/SB0 CE Output Chip enable output
12 P24/BUSY CLK Output Clock output
13 P23/STB CD RWC Output CD DSP read write cont
14 P22/SCK1 CD WRQ Input CD DSP write request cont
15 P21/S01 CD PCCL Output CD DSP PCCL
16 P20/SI1 CD COIN Output CD COIN (Data output)
17 RESET RESET Input Reset
18 P74 CD SQOUT Input CD SQOUT (Data input)
19 P73 TIMER LED Output TIMER LED control
20 AVss AVSS — Analog ground
21 P17 CD CQCK Output CD CQCK (Clock output)
22 P16 CD DSP RES Output CD DSP reset
23 P15 CD FRF Input CD RF level detection
24 P14/ANI4 A/D T2 RUN Input Analog data T2 RUN
25 P13/ANI3 A/D KEYIN 1 Input Key input 1
26 P12/ANI2 A/D KEYIN 2 Input Key input 2
27 P11/ANI1 A/D KEYIN 3 Input Key input 3
28 P10/ANI0 A/D DIST Input Key output distination
29 AVDD AVDD — Analog VDD
30 AVREF AVREF — Analog REF voltage
IC701 RH-iX0282AWZZ: System Microcomputer (IX0282AW) (1/2)
Port Name Terminal NamePin No. Input/Output Function
CD-C606/1900,CP-C606/1900
– 41 –
31* P04/XT1 OPEN — Open
32* XT2 — Open
33 Vss VSS — Ground voltage
34 X1 — Main clock
35 X2 — Main clock
36 P37 CD SLM + Output CD slide motor +
37 P36/BUZ CD SLM - Output CD slide motor -
38 P35/PCL CD PUIN SW Input CD PUIN switch
39 P34/TI2 CD O/C SW Input CD open close switch
40 P33/TI1 CD DISC NO SW Input CD DISC NO. switch
41 P32/TO2 CD U/D SW Input CD UP/DOWN switch
42 P31/TO1 REC/PLAY Output Tape record playback
43 P30/TO0 T_BIAS Output Tape record bias control
44 P03/INTP3/CI0 T T1T2 Output Tape T1/T2 change
45* P02/INTP2 TAMUTE (NC) Output Tape play mute
46 P02/INTP1 SYSTEM STOP Input System stop input
47 P00/INTP0/TI0 REMOCON Input Remocon input
48 IC (Vpp) — IC
49 P72 CAM SW Input Tape cam switch
50 P71 T. SOL Output Tape solenoid control
51 P70 T. MOTOR Output Tape motor control
52 VDD VDD — VDD
53 P127/FIP33 T1 FAS Input Tape full autostop pulse input
NOTE:Parts marked with “ ” are important for maintaining the safety of the set.Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
MODEL CD-C606CD-C1900CP-C606CP-C1900
“HOW TO ORDER REPLACEMENT PARTS”To have your order filled promptly and correctly, please furnish thefollowing information.
1. MODEL NUMBER 2. REF. No.3. PART NO. 4. DESCRIPTION
MARK: SPARE PARTS-DELIVERY SECTION
Explanation of capacitors/resistors parts codesCapacitorsVCC ....................... Ceramic typeVCK........................ Ceramic typeVCT ........................ Semiconductor typeVC • • MF ............... Cylindrical type (without lead wire)VC • • MN ............... Cylindrical type (without lead wire)VC • • TV ................ Square type (without lead wire)VC • • TQ ............... Square type (without lead wire)VC • • CY ............... Square type (without lead wire)VC • • CZ ............... Square type (without lead wire)VC • • • • • • • • • J .. The 13th character represents capacity difference.
If there are no indications for the electrolytic capacitors, error is ±20%.
ResistorsVRD ....................... Carbon-film typeVRS........................ Carbon-film typeVRN ....................... Metal-film typeVR • • MF ............... Cylindrical type (without lead wire)VR • • MN ............... Cylindrical type (without lead wire)VR • • TV ................ Square type (without lead wire)VR • • TQ ............... Square type (without lead wire)VR • • CY ............... Square type (without lead wire)VR • • CZ ............... Square type (without lead wire)VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "F" ±1%, "D" ±0.5%.)
If there are no indications for other parts, the resistors are ±5%carbon-film type.
For U.S.A. onlyContact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor,Please call Toll-Free;1-800-BE-SHARP
CD-C606 mini component system consisting ofCD-C606 mini component system andCP-C606 speaker system
CD-C1900 mini component system consisting ofCD-C1900 mini component system andCP-C1900 speaker system
PRICERANK
DESCRIPTIONNO. PARTS CODE NO. PARTS CODE PRICERANK DESCRIPTION
CD-C606/1900,CP-C606/1900
– 1 –
CD-C606/1900
INTEGRATED CIRCUITS
IC1 VHILA9241M/-1 J AS Servo Amp.,LA9241MIC2 VHILC78622N-1 J AY Servo/Signal Control,LC78622NIC3 VHIM63001FP-1 J AX Focus/Tracking/Spin/Slide
Driver,M63001FPIC301 VHITA7358AP-1 J AG FM Front End,TA7358APIC302 VHILC72131/-1 J AP PLL Controller,LC72131IC303 VHILA1805//-1 J AM FM IF DET./FM MPX./AM IF,
LA1805IC401 VHIM62439SP-1 J AG Audio Processor,M62439SPIC501 VHIAN7345K/-1 J AM Playback and Record/Playback
Amp.,AN7345KIC601 VHILA4282//-1 J AM Power Amp.,LA4282IC701 RH-IX0282AWZZ J AP System Microcomputer,
IX0282AWIC702 VHIKIA7042P-1 J AG Reset,KIA7042PIC901 VHIAN78L05/-1 J AE Constant Voltage Regulator,
AN78L05IC902 VHIKIA7806P-1 J AG Voltage Regulator,KIA7806PIC903 VHIKIA7812P-1 J AE Voltage Regulator,KIA7812PIC904 VHIAN78L05/-1 J AE Constant Voltage Regulator,
AN78L05
TRANSISTORS
Q1 VS2SA1318//-1 J AC Silicon,PNP,2SA1318Q51 VSKRC102M//-1 J AC Digital,NPN,KRC102 MQ52 VSKTC3203Y/-1 J AC Silicon,NPN,KTC3203 YQ301 VSKTC3194Y/-1 J AD Silicon,NPN,KTC3194 YQ351 VSKRA102M//-1 J AC Digital,PNP,KRA102 MQ381 VSKRA109M//-1 J AC Digital,PNP,KRA109 MQ401,402 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GRQ501 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GRQ502~505 VS2SC2389SE-1 J AD Silicon,NPN,2SC2389 SEQ506,507 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GRQ508,509 VSKRC104M//-1 J AC Digital,NPN,KRC104 MQ512,513 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GRQ514 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GRQ515 VSKRC104M//-1 J AC Digital,NPN,KRC104 MQ516 VSKTC3203Y/-1 J AC Silicon,NPN,KTC3203 YQ631,632 VSKRC102M//-1 J AC Digital,NPN,KRC102 MQ701 VSKTA1273Y/-1 J AE Silicon,PNP,KTA1273 YQ702 VSKTA1271Y/-1 J AC Silicon,PNP,KTA1271 YQ703 VSKRC107M//-1 J AC Digital,NPN,KRC107 MQ704 VSKRC102M//-1 J AC Digital,NPN,KRC102 MQ901 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GRQ902 VSKRC107M//-1 J AC Digital,NPN,KRC107 M
DIODES
D1 VHD1SS133//-1 J AA Silicon,1SS133D81,82 VHD1SS133//-1 J AA Silicon,1SS133D91~93 VHD1SS133//-1 J AA Silicon,1SS133D301 VHDDS1SS133-1 J AB Silicon,DS1SS133D303,304 VHDDS1SS133-1 J AB Silicon,DS1SS133D381 VHDDS1SS133-1 J AB Silicon,DS1SS133D701~705 VHDDS1SS133-1 J AB Silicon,DS1SS133D707,708 VHDDS1SS133-1 J AB Silicon,DS1SS133D743 VHDDS1SS133-1 J AB Silicon,DS1SS133D901~904 VHDDS1SS133-1 J AB Silicon,DS1SS133D905~909 VHD1N4004S/-1 J AB Silicon,1N4004SD910,911 VHDRL203F//-1 J AE Silicon,RL203FD912,913 VHD1N4004S/-1 J AB Silicon,1N4004SD914,915 VHDRL203F//-1 J AE Silicon,RL203FD916,917 VHD1N4004S/-1 J AB Silicon,1N4004SD918~920 VHDDS1SS133-1 J AB Silicon,DS1SS133D921~925 VHD1SS133//-1 J AA Silicon,1SS133LED701 VHPSLI342UCJ1 J AC LED,Red,SLI342UCJ1VD301,302 VHCSVC211C/-1 J AG Variable,Capacitance,SVC211CVD303 VHDSVC348S/-1 J Silicon,SVC348SZD61 VHEMTZJ5R6B-1 J AD Zener,5.6V,MTZJ5.6BZD351 VHEDZ5R1BSB-1 J AC Zener,5.1V,DZ5.1BSBZD401,402 VHEDZ2R4BSB-1 J AB Zener,2.4V,DZ2.4BSBZD901 VHEDZ6R2BSA-1 J AB Zener,6.2V,DZ6.2BSAZD902 VHEDZ300BSB-1 J AB Zener,30V,DZ300BSB
FILTERS
BF301 RFILR0008AWZZ J AE Band Pass FilterCF301 RFILF0124AFZZ J AD FM IF,10.7 MHzCF351 92LFILTA1768A J AE AM IF
TRANSFORMERS
! PT901 RTRNP0253AWZZ J BA Power! PT902 RTRNP0239AWZZ J AP Power
T301 RCILB0060AWZZ J AC FM OscillationT302 RCILI0012AWZZ J AD FM IFT331 RCILA0052AWZZ J AE AM AntennaT333 RCILB0058AWZZ J AC AM OscillationT381 RCILI0016AFZZ J FM DetectionT382 RCILI0015AWZZ J AE AM IF
COILS
L61 VP-XHR82K0000 J AC 0.82 µH,ChokeL312 RCILR0029AWZZ J AA FM RFL317 VP-DH101K0000 J AB 100 µH,ChokeL503 VP-MK331K0000 J AB 330 µH,ChokeL701 VP-DH101K0000 J AB 100 µH,Choke
VARIABLE RESISTOR
VR381 RVR-M0025AWZZ J AC 6.8 kohms (B),Semi-VR [VCO]
C1 VCEAZA1CW476M J AB 47 µF,16V,ElectrolyticC2 VCKYTV1HB103K J AA 0.01 µF,50VC3 VCEAZA1HW105M J AB 1 µF,50V,ElectrolyticC4 VCEAZA1HW104M J AB 0.1 µF,50V,ElectrolyticC5,6 VCTYPA1CX333K J AA 0.033 µF,16VC7 VCEAZA1HW104M J AB 0.1 µF,50V,ElectrolyticC8 VCTYPA1CX683K J AA 0.068 µF,16VC9 VCTYPA1CX473K J AA 0.047 µF,16VC10 VCCSTV1HL181J J AA 180 pF,50VC11,12 VCTYPA1CX104K J AB 0.1 µF,16VC13 VCKYTV1HB331K J AA 330 pF,50VC14,15 VCKYTV1HB103K J AA 0.01 µF,50VC16 VCKYTV1HB472K J AA 0.0047 µF,50VC17 VCKYTV1HB102K J AA 0.001 µF,50VC18 VCEAZA1HW474M J AB 0.47 µF,50V,ElectrolyticC19 VCEAZA1HW105M J AB 1 µF,50V,ElectrolyticC20 VCEAZA1CW476M J AB 47 µF,16V,ElectrolyticC21 VCKYTV1HB332K J AA 0.0033 µF,50VC22 VCCSPA1HL221J J AA 220 pF,50VC23 VCKYTV1HB272K J AA 0.0027 µF,50VC24 VCCSTV1HL2R2C J AB 2.2 pF,50VC25 VCCSTV1HL270J J AA 27 pF,50VC26 VCTYPA1CX333K J AA 0.033 µF,16VC27 VCKYTV1HB102K J AA 0.001 µF,50VC28 VCTYPA1CX104K J AB 0.1 µF,16VC29 VCEAZA1HW475M J AB 4.7 µF,50V,ElectrolyticC30 VCEAZA1HW104M J AB 0.1 µF,50V,ElectrolyticC31 VCEAZA0JW227M J AC 220 µF,6.3V,ElectrolyticC32 VCKYTV1HB103K J AA 0.01 µF,50VC33 VCEAZA1HW474M J AB 0.47 µF,50V,ElectrolyticC34 VCEAZA1HW334M J AB 0.33 µF,50V,ElectrolyticC35 VCEAZA1HW105M J AB 1 µF,50V,ElectrolyticC36 VCEAZA1CW107M J AC 100 µF,16V,ElectrolyticC37 VCKZPA1HF223Z J AA 0.022 µF,50VC38 VCKYTV1HB103K J AA 0.01 µF,50VC39,40 VCTYPA1CX473K J AA 0.047 µF,16VC43 VCEAZA0JW337M J AC 330 µF,6.3V,ElectrolyticC44~47 VCCCTV1HH101J J AA 100 pF (CH),50VC48 VCCSPA1HL101J J AA 100 pF,50VC49 VCCCTV1HH101J J AA 100 pF (CH),50VC50 VCKYTV1EF223Z J AA 0.022 µF,25VC51,52 VCEAZA1CW107M J AC 100 µF,16V,ElectrolyticC54 VCKYTV1HB102K J AA 0.001 µF,50V
NO. PRICERANK DESCRIPTIONPARTS CODENO. PARTS CODE PRICE
RANK DESCRIPTION
CD-C606/1900,CP-C606/1900
– 2 –
C55 VCEAZA1CW107M J AC 100 µF,16V,ElectrolyticC56 VCKYTV1EF223Z J AA 0.022 µF,25VC57 VCKYBT1HB102K J AA 0.001 µF,50VC71,72 VCEAZA1HW106M J AB 10 µF,50V,ElectrolyticC73,74 VCKYTV1HB221K J AA 220 pF,50VC75 VCKYTV1HB102K J AA 0.001 µF,50VC76 VCKZPA1HF223Z J AA 0.022 µF,50VC77 VCEAZA1CW107M J AC 100 µF,16V,ElectrolyticC82 VCEAZA1CW107M J AC 100 µF,16V,ElectrolyticC83 VCTYBT1EF223Z J AA 0.022 µF,25VC303 VCCSMN1HL100J J AA 10 pF,50VC304 VCTYMN1CY103N J AA 0.01 µF,16VC305 VCCSMN1HL4R7C J AA 4.7 pF,50VC306 VCTYMN1EF223Z J AA 0.022 µF,25VC307 VCEAZA1CW106M J AC 10 µF,16V,ElectrolyticC308 VCCUMN1HJ4R7D J AA 4.7 pF (UJ),50VC309 VCKYMN1HB102K J AA 0.001 µF,50VC310 VCCCMN1HH150J J AA 15 pF (CH),50VC311 VCCSMN1HL180J J AA 18 pF,50VC312 VCTYMN1EF223Z J AA 0.022 µF,25VC313 VCCCMN1HH220J J AA 22 pF (CH),50VC314,315 VCTYMN1CX472K J AA 0.0047 µF,16VC316 VCTYMN1EF223Z J AA 0.022 µF,25VC317 VCKYMN1HB102K J AA 0.001 µF,50VC318 VCKYBT1HB101K J AA 100 pF,50VC319 VCKYMN1HB102K J AA 0.001 µF,50VC324 VCCUMN1HJ3R9K J AA 3.9 pF (UJ),50VC330 VCEAZA1CW106M J AC 10 µF,16V,ElectrolyticC331 VCTYMN1EF223Z J AA 0.022 µF,25VC332 VCCUMN1HJ180J J AA 18 pF (UJ),50VC333 VCKYPA1HF473Z J AB 0.047 µF,50VC334 VCTYMN1EF223Z J AA 0.022 µF,25VC335 VCCUMN1HJ180J J AA 18 pF (UJ),50VC336 VCKYMN1HB561K J AA 560 pF,50VC340 VCKYPA1HB102K J AA 0.001 µF,50VC341 VCKYPA1HB102K J AA 0.001 µF,50VC350 VCCCMN1HH150J J AA 15 pF (CH),50VC351 VCKYPA1HB102K J AA 0.001 µF,50VC352 VCCCMN1HH120J J AA 12 pF (CH),50VC353 VCKYMN1HB102K J AA 0.001 µF,50VC354 VCEAEA1HW105M J AB 1 µF,50V,ElectrolyticC355 VCKYMN1HB101K J AA 100 pF,50VC356 VCTYMN1EF223Z J AA 0.022 µF,25VC357 VCEAZA1CW476M J AB 47 µF,16V,ElectrolyticC380 VCTYMN1EF223Z J AA 0.022 µF,25VC381 VCEAZA1AW227M J AC 220 µF,10V,ElectrolyticC382 VCTYMN1CX222K J AA 0.0022 µF,16VC383 VCKYMN1HB221K J AA 220 pF,50VC384 VCTYMN0JY183M J AA 0.018 µF,6.3VC385~387 VCEAZA1EW335M J AB 3.3 µF,25V,ElectrolyticC388 CPU100V1500PJ J AC 0.0015 µF,100V, PolypropyleneC389,390 VCTYMN1EF223Z J AA 0.022 µF,25VC391 VCEAEA1CW226M J AB 22 µF,16V,ElectrolyticC392 VCEAEA1HW105M J AB 1 µF,50V,ElectrolyticC393,394 VCTYPA1CX153K J AA 0.015 µF,16VC395,396 VCEAEA1HW105M J AB 1 µF,50V,ElectrolyticC401,402 VCKYMN1HB102K J AA 0.001 µF,50VC403 VCEAZA1EW226M J AB 22 µF,25V,ElectrolyticC404,405 VCEAZA1HW106M J AB 10 µF,50V,ElectrolyticC406 VCEAZA1HW475M J AB 4.7 µF,50V,ElectrolyticC410 VCQYKA1HM224K J AB 0.22 µF,50V,MylarC411 VCQYKA1HM333K J AB 0.033 µF,50V,MylarC412 VCQYKA1HM224K J AB 0.22 µF,50V,MylarC413 VCEAZA1HW106M J AB 10 µF,50V,ElectrolyticC414 VCQYKA1HM223K J AB 0.022 µF,50V,MylarC415 VCQYKA1HM333K J AB 0.033 µF,50V,MylarC416 VCQYKA1HM224K J AB 0.22 µF,50V,MylarC417 VCCUMN1HJ100J J AA 10 pF (UJ),50VC418 VCEAZA1HW475M J AB 4.7 µF,50V,ElectrolyticC422 VCEAZA1HW106M J AB 10 µF,50V,ElectrolyticC423 VCTYMN1EF223Z J AA 0.022 µF,25VC424 VCQYKA1HM224K J AB 0.22 µF,50V,MylarC451,452 VCKYMN1HB102K J AA 0.001 µF,50VC453,454 VCTYMN1CX222K J AA 0.0022 µF,16VC501,502 VCKYMN1HB102K J AA 0.001 µF,50VC503,504 VCKYMN1HB181K J AA 180 pF,50VC505 VCKYPA1HF473Z J AB 0.047 µF,50VC506,507 VCKYMN1HB102K J AA 0.001 µF,50VC508 VCEAZA1CW107M J AC 100 µF,16V,ElectrolyticC509~512 VCKYMN1HB331K J AA 330 pF,50VC514,515 VCEAZA1AW227M J AC 220 µF,10V,ElectrolyticC516,517 VCTYPA1EX333K J AA 0.033 µF,25V
C518,519 VCKYMN1HB181K J AA 180 pF,50VC520,521 VCEAEA1HW105M J AB 1 µF,50V,ElectrolyticC523 VCTYMN1EF223Z J AA 0.022 µF,25VC525 VCEAEA1HW335M J AB 3.3 µF,50V,ElectrolyticC526,527 VCKYMN1HB102K J AA 0.001 µF,50VC528,529 VCEAEA1CW226M J AB 22 µF,16V,ElectrolyticC530,531 VCTYPA1CX683K J AA 0.068 µF,16VC532,533 VCTYMN1CX332K J AA 0.0033 µF,16VC534,535 VCEAEA1HW105M J AB 1 µF,50V,ElectrolyticC536 VCEAEA1CW226M J AB 22 µF,16V,ElectrolyticC537 VCEAZA1AW227M J AC 220 µF,10V,ElectrolyticC538 VCKYMN1HB471K J AA 470 pF,50VC539 VCQPKA2AA392J J AB 0.0039 µF,100V,PolypropyleneC540 VCQYKA1HM273K J AB 0.027 µF,50V,MylarC541 VCEAZA1CW476M J AB 47 µF,16V,ElectrolyticC551,552 VCTYMN1CY103N J AA 0.01 µF,16VC601,602 VCEAZA1CW106M J AC 10 µF,16V,ElectrolyticC603,604 VCKYPA1HB102K J AA 0.001 µF,50VC605 VCEAZA1EW107M J AB 100 µF,25V,ElectrolyticC606,607 VCQYKA1HM823K J AC 0.082 µF,50V,MylarC608 VCEAZA1EW107M J AB 100 µF,25V,ElectrolyticC609,610 VCEAZA1EW477M J AD 470 µF,25V,ElectrolyticC611,612 VCQYKA1HM473K J AB 0.047 µF,50V,MylarC615,616 VCKYMN1HB820K J AA 82 pF,50VC631 VCQYKA1HM223K J AB 0.022 µF,50V,MylarC632 VCEAZA1EW476M J AB 47 µF,25V,ElectrolyticC633 VCKYBT1HB221K J AA 220 pF,50VC634 VCQYKA1HM223K J AB 0.022 µF,50V,MylarC635 VCEAZA1HW106M J AB 10 µF,50V,ElectrolyticC701 VCCCMN1HH150J J AA 15 pF (CH),50VC702 VCCCMN1HH180J J AA 18 pF (CH),50VC703,704 VCEAEA1HW105M J AB 1 µF,50V,ElectrolyticC705 VCEAZA1CW476M J AB 47 µF,16V,ElectrolyticC706 VCTYMN1EF223Z J AA 0.022 µF,25VC707 VCEAZA0JW227M J AC 220 µF,6.3V,ElectrolyticC708 VCKYMN1HB102K J AA 0.001 µF,50VC709 VCTYPA1CX223K J AA 0.022 µF,16VC710 VCKYPA1HB103K J AA 0.01 µF,50VC712 VCEAEA1HW335M J AB 3.3 µF,50V,ElectrolyticC713 VCKYPA1HF223Z J AB 0.022 µF,50VC714 VCTYMN1EF223Z J AA 0.022 µF,25VC715 VCEAZA1EW476M J AB 47 µF,25V,ElectrolyticC770 VCEAZA1HW104M J AB 0.1 µF,50V,ElectrolyticC772 VCTYMN1EF223Z J AA 0.022 µF,25VC773 VCTYPA1CX472K J AA 0.0047 µF,16VC774 VCEAZA1AW107M J AB 100 µF,10V,ElectrolyticC775 VCEAZA1HW225M J AB 2.2 µF,50V,ElectrolyticC901 VCEAZA1CW476M J AB 47 µF,16V,ElectrolyticC902 VCQYKA1HM223K J AB 0.022 µF,50V,MylarC903 VCEAZA1EW476M J AB 47 µF,25V,ElectrolyticC904,905 VCQYKA1HM473K J AB 0.047 µF,50V,MylarC906 VCQYKA1HM223K J AB 0.022 µF,50V,MylarC907 VCEAZA1CW107M J AC 100 µF,16V,ElectrolyticC908~910 VCQYKA1HM104K J AB 0.1 µF,50V,MylarC911 VCEAZW1EW338M J AG 3300 µF,25V,ElectrolyticC912 VCEAZW1HW228M J AH 2200 µF,50V,ElectrolyticC913 VCEAZV1EW108M J AE 1000 µF,25V,ElectrolyticC914 VCEAZA1EW107M J AB 100 µF,25V,ElectrolyticC915 VCEAZA1VW107M J AC 100 µF,35V,ElectrolyticC916~918 VCEAZA1HW476M J AB 47 µF,50V,ElectrolyticC919,920 VCEAZA1HW107M J AC 100 µF,50V,ElectrolyticC921,922 VCQYKA1HM104K J AB 0.1 µF,50V,MylarC923,924 VCQYKA1HM473K J AB 0.047 µF,50V,MylarC925 VCEAZA0JW108M J AC 1000 µF,6.3V,ElectrolyticC926 VCEAZA1CW106M J AC 10 µF,16V,ElectrolyticC927 VCEAZA1EW477M J AD 470 µF,25V,ElectrolyticC928 VCQYKA1HM473K J AB 0.047 µF,50V,Mylar
! C929 RC-KZ001LAWZZ J AB 0.0047 µF,250V
RESISTORS
VRD-MN2BD000C J AA 0 ohm,Jumper,ø1.4×3.5mm,IvoryVRS-TV2AB000J J AA 0 ohm,Jumper,1.25×2mm,Green
R1 VRS-TV2AB220J J AA 22 ohms,1/10WR2 VRD-ST2CD102J J AA 1 kohm,1/6WR8 VRS-TV2AB153J J AA 15 kohms,1/10WR9 VRS-TV2AB104J J AA 100 kohm,1/10WR10 VRS-TV2AB222J J AA 2.2 kohms,1/10WR11 VRD-ST2CD682J J AA 6.8 kohms,1/6WR12 VRD-ST2CD101J J AA 100 ohm,1/6WR13 VRS-TV2AB102J J AA 1 kohm,1/10WR14 VRS-TV2AB273J J AA 27 kohms,1/10W
PRICERANK
DESCRIPTIONNO. PARTS CODE NO. PARTS CODE PRICERANK DESCRIPTION
CD-C606/1900,CP-C606/1900
– 3 –
R15 VRS-TV2AB123J J AA 12 kohms,1/10WR16 VRS-TV2AB332J J AA 3.3 kohms,1/10WR17 VRS-TV2AB333J J AA 33 kohms,1/10WR18 VRS-TV2AB153J J AA 15 kohms,1/10WR19 VRD-ST2CD102J J AA 1 kohm,1/6WR20 VRS-TV2AB102J J AA 1 kohm,1/10WR21 VRS-TV2AB152J J AA 1.5 kohms,1/10WR22 VRS-TV2AB821J J AA 820 ohms,1/10WR23 VRS-TV2AB103J J AA 10 kohm,1/10WR24 VRS-TV2AB473J J AA 47 kohms,1/10WR25 VRS-TV2AB152J J AA 1.5 kohms,1/10WR26 VRS-TV2AB823J J AA 82 kohms,1/10WR27 VRS-TV2AB393J J AA 39 kohms,1/10WR28 VRS-TV2AB103J J AA 10 kohm,1/10WR29 VRS-TV2AB563J J AA 56 kohms,1/10WR30 VRS-TV2AB682J J AA 6.8 kohms,1/10WR31 VRS-TV2AB122J J AA 1.2 kohms,1/10WR32 VRS-TV2AB103J J AA 10 kohm,1/10WR33 VRS-TV2AB122J J AA 1.2 kohms,1/10WR34 VRS-TV2AB102J J AA 1 kohm,1/10WR35,36 VRS-TV2AB224J J AA 220 kohms,1/10WR37 VRD-ST2CD823J J AA 82 kohms,1/6WR38 VRS-TV2AB471J J AA 470 ohms,1/10WR39 VRD-ST2CD102J J AA 1 kohm,1/6WR40 VRS-TV2AB562J J AA 5.6 kohms,1/10WR41,42 VRS-TV2AB473J J AA 47 kohms,1/10WR43 VRS-TV2AB563J J AA 56 kohms,1/10WR44 VRS-TV2AB333J J AA 33 kohms,1/10WR45 VRS-TV2AB472J J AA 4.7 kohms,1/10WR46 VRS-TV2AB561J J AA 560 ohms,1/10WR47 VRD-ST2CD103J J AA 10 kohm,1/6WR50 VRS-TV2AB681J J AA 680 ohms,1/10WR51 VRD-ST2CD335J J AA 3.3 Mohms,1/6WR52 VRS-TV2AB273J J AA 27 kohms,1/10WR53 VRS-TV2AB122J J AA 1.2 kohms,1/10WR55 VRD-ST2CD101J J AA 100 ohm,1/6WR56 VRS-TV2AB682J J AA 6.8 kohms,1/10WR57 VRD-ST2CD102J J AA 1 kohm,1/6WR58~60 VRS-TV2AB102J J AA 1 kohm,1/10WR61~63 VRD-ST2CD102J J AA 1 kohm,1/6WR64 VRS-TV2AB220J J AA 22 ohms,1/10WR65 VRD-ST2CD102J J AA 1 kohm,1/6WR66 VRS-TV2AB221J J AA 220 ohms,1/10WR71,72 VRD-ST2CD272J J AA 2.7 kohms,1/6WR73,74 VRS-TV2AB104J J AA 100 kohm,1/10WR80,81 VRD-ST2CD821J J AA 820 ohms,1/6WR82,83 VRS-TV2AB391J J AA 390 ohms,1/10WR84 VRD-ST2CD222J J AA 2.2 kohms,1/6WR88,89 VRD-ST2CD122J J AA 1.2 kohms,1/6WR90 VRD-ST2CD221J J AA 220 ohms,1/6WR91 VRD-ST2CD102J J AA 1 kohm,1/6WR93 VRS-TV2AB221J J AA 220 ohms,1/10WR301 VRD-MN2BD100J J AA 10 ohm,1/8WR309 VRD-MN2BD103J J AA 10 kohm,1/8WR311 VRD-MN2BD104J J AA 100 kohm,1/8WR312 VRD-ST2CD470J J AA 47 ohms,1/6WR313 VRD-MN2BD333J J AA 33 kohms,1/8WR314 VRD-ST2CD220J J AA 22 ohms,1/6WR315 VRD-MN2BD821J J AA 820 ohms,1/8WR317 VRD-MN2BD472J J AA 4.7 kohms,1/8WR322 VRD-MN2BD681J J AA 680 ohms,1/8WR323 VRD-MN2BD224J J AA 220 kohms,1/8WR341 VRD-MN2BD103J J AA 10 kohm,1/8WR343 VRD-MN2BD683J J AA 68 kohms,1/8WR351 VRD-MN2BD152J J AA 1.5 kohms,1/8WR352 VRD-MN2BD103J J AA 10 kohm,1/8WR353 VRD-MN2BD222J J AA 2.2 kohms,1/8WR354~358 VRD-ST2CD102J J AA 1 kohm,1/6WR361 VRD-MN2BD473J J AA 47 kohms,1/8WR380 VRD-MN2BD392J J AA 3.9 kohms,1/8WR381 VRD-MN2BD333J J AA 33 kohms,1/8WR382 VRD-MN2BD152J J AA 1.5 kohms,1/8WR383 VRD-MN2BD122J J AA 1.2 kohms,1/8WR384 VRD-MN2BD153J J AA 15 kohms,1/8WR385 VRD-MN2BD103J J AA 10 kohm,1/8WR386 VRD-ST2EE391J J AA 390 ohms,1/4WR387 VRD-ST2EE331J J AA 330 ohms,1/4WR388 VRD-MN2BD332J J AA 3.3 kohms,1/8WR389 VRD-MN2BD103J J AA 10 kohm,1/8WR390 VRD-ST2CD222J J AA 2.2 kohms,1/6WR391 VRD-ST2CD470J J AA 47 ohms,1/6WR398 VRD-MN2BD562J J AA 5.6 kohms,1/8W
R401 VRD-MN2BD331J J AA 330 ohms,1/8WR402 VRD-ST2CD331J J AA 330 ohms,1/6WR405 VRD-MN2BD222J J AA 2.2 kohms,1/8WR406 VRD-ST2CD222J J AA 2.2 kohms,1/6WR407 VRD-MN2BD223J J AA 22 kohms,1/8WR408,409 VRD-MN2BD472J J AA 4.7 kohms,1/8WR410 VRD-MN2BD332J J AA 3.3 kohms,1/8WR411 VRD-ST2CD332J J AA 3.3 kohms,1/6WR412 VRD-MN2BD331J J AA 330 ohms,1/8WR413 VRD-MN2BD222J J AA 2.2 kohms,1/8WR414~416 VRD-ST2CD152J J AA 1.5 kohms,1/6WR417 VRD-RT2HD561J J AA 560 ohms,1/2WR418 VRD-MN2BD562J J AA 5.6 kohms,1/8WR419 VRD-MN2BD103J J AA 10 kohm,1/8WR420,421 VRD-MN2BD152J J AA 1.5 kohms,1/8WR422 VRD-ST2CD152J J AA 1.5 kohms,1/6WR423 VRD-ST2CD223J J AA 22 kohms,1/6WR424 VRD-RT2HD821J J AA 820 ohms,1/2WR425 VRD-MN2BD331J J AA 330 ohms,1/8WR426 VRD-MN2BD222J J AA 2.2 kohms,1/8WR428 VRD-MN2BD153J J AA 15 kohms,1/8WR430 VRD-MN2BD153J J AA 15 kohms,1/8WR451,452 VRD-ST2CD182J J AA 1.8 kohms,1/6WR501 VRD-MN2BD103J J AA 10 kohm,1/8WR502 VRD-ST2CD103J J AA 10 kohm,1/6WR503 VRD-MN2BD103J J AA 10 kohm,1/8WR504 VRD-MN2BD222J J AA 2.2 kohms,1/8WR505,506 VRD-MN2BD332J J AA 3.3 kohms,1/8WR507 VRD-MN2BD222J J AA 2.2 kohms,1/8WR508,509 VRD-MN2BD103J J AA 10 kohm,1/8WR510 VRD-ST2CD472J J AA 4.7 kohms,1/6WR511,512 VRD-MN2BD473J J AA 47 kohms,1/8WR513 VRD-ST2CD472J J AA 4.7 kohms,1/6WR514 VRD-MN2BD102J J AA 1 kohm,1/8WR515 VRD-ST2CD102J J AA 1 kohm,1/6WR516 VRD-MN2BD151J J AA 150 ohms,1/8WR517 VRD-MN2BD102J J AA 1 kohm,1/8WR518 VRD-ST2CD102J J AA 1 kohm,1/6WR522,523 VRD-ST2CD270J J AA 27 ohms,1/6WR524,525 VRD-MN2BD104J J AA 100 kohm,1/8WR526,527 VRD-MN2BD472J J AA 4.7 kohms,1/8WR531,532 VRD-ST2CD102J J AA 1 kohm,1/6WR533,534 VRD-MN2BD333J J AA 33 kohms,1/8WR536 VRD-MN2BD683J J AA 68 kohms,1/8WR537,538 VRD-MN2BD562J J AA 5.6 kohms,1/8WR539,540 VRD-MN2BD682J J AA 6.8 kohms,1/8WR541,542 VRD-MN2BD561J J AA 560 ohms,1/8WR543 VRD-ST2CD823J J AA 82 kohms,1/6WR544,545 VRD-MN2BD560J J AA 56 ohms,1/8WR546 VRD-ST2CD103J J AA 10 kohm,1/6WR547,548 VRD-MN2BD103J J AA 10 kohm,1/8WR549 VRD-ST2CD103J J AA 10 kohm,1/6WR550 VRD-ST2CD823J J AA 82 kohms,1/6WR551 VRD-ST2EE221J J AA 220 ohms,1/4WR552 VRD-RT2HD151J J AA 150 ohms,1/2WR553 VRD-MN2BD104J J AA 100 kohm,1/8WR554 VRD-ST2CD473J J AA 47 kohms,1/6WR555 VRD-MN2BD473J J AA 47 kohms,1/8WR556 VRD-MN2BD472J J AA 4.7 kohms,1/8WR557 VRD-MN2BD120J J AA 12 ohms,1/8WR561 VRD-ST2CD223J J AA 22 kohms,1/6WR601 VRD-ST2CD472J J AA 4.7 kohms,1/6WR602 VRD-MN2BD472J J AA 4.7 kohms,1/8WR603,604 VRD-ST2CD332J J AA 3.3 kohms,1/6WR605 VRD-ST2CD121J J AA 120 ohms,1/6WR606,607 VRD-ST2CD102J J AA 1 kohm,1/6WR608 VRD-ST2CD121J J AA 120 ohms,1/6WR609,610 VRD-RT2HD271J J AA 270 ohms,1/2WR611,612 VRD-ST2EE4R7J J AA 4.7 ohms,1/4WR613,614 VRD-ST2EE331J J AA 330 ohms,1/4WR631 VRD-ST2CD223J J AA 22 kohms,1/6WR632 VRD-ST2EE821J J AA 820 ohms,1/4WR633 VRD-ST2CD563J J AA 56 kohms,1/6WR701~703 VRD-MN2BD102J J AA 1 kohm,1/8WR704~708 VRD-MN2BD102J J AA 1 kohm,1/8WR709 VRD-ST2CD102J J AA 1 kohm,1/6WR710,711 VRD-MN2BD102J J AA 1 kohm,1/8WR712 VRD-ST2CD222J J AA 2.2 kohms,1/6WR713 VRD-MN2BD102J J AA 1 kohm,1/8WR714 VRD-ST2CD222J J AA 2.2 kohms,1/6WR715 VRD-MN2BD102J J AA 1 kohm,1/8WR716 VRD-ST2CD102J J AA 1 kohm,1/6W
NO. PRICERANK DESCRIPTIONPARTS CODENO. PARTS CODE PRICE
RANK DESCRIPTION
CD-C606/1900,CP-C606/1900
– 4 –
R717~719 VRD-MN2BD102J J AA 1 kohm,1/8WR721~725 VRD-MN2BD102J J AA 1 kohm,1/8WR726 VRD-ST2CD102J J AA 1 kohm,1/6WR727 VRD-MN2BD102J J AA 1 kohm,1/8WR728,729 VRD-ST2CD102J J AA 1 kohm,1/6WR730~734 VRD-MN2BD102J J AA 1 kohm,1/8WR735~738 VRD-ST2CD102J J AA 1 kohm,1/6WR739,740 VRD-MN2BD103J J AA 10 kohm,1/8WR741 VRD-ST2CD104J J AA 100 kohm,1/6WR742 VRD-MN2BD103J J AA 10 kohm,1/8WR743 VRD-ST2CD122J J AA 1.2 kohms,1/6WR745 VRD-MN2BD103J J AA 10 kohm,1/8WR746,747 VRD-ST2CD103J J AA 10 kohm,1/6WR748 VRD-MN2BD103J J AA 10 kohm,1/8WR749 VRD-ST2CD103J J AA 10 kohm,1/6WR750~754 VRD-MN2BD103J J AA 10 kohm,1/8WR755 VRD-MN2BD332J J AA 3.3 kohms,1/8WR756,757 VRD-ST2CD103J J AA 10 kohm,1/6WR758 VRD-ST2CD182J J AA 1.8 kohms,1/6WR761 VRD-ST2CD821J J AA 820 ohms,1/6WR762 VRD-ST2CD122J J AA 1.2 kohms,1/6WR763 VRD-MN2BD821J J AA 820 ohms,1/8WR764 VRD-ST2CD821J J AA 820 ohms,1/6WR765 VRD-ST2CD122J J AA 1.2 kohms,1/6WR766 VRD-MN2BD122J J AA 1.2 kohms,1/8WR767 VRD-ST2CD152J J AA 1.5 kohms,1/6WR768 VRD-MN2BD152J J AA 1.5 kohms,1/8WR770,771 VRD-ST2CD182J J AA 1.8 kohms,1/6WR772 VRD-RT2HD3R3J J AA 3.3 ohms,1/2WR773,774 VRD-ST2CD222J J AA 2.2 kohms,1/6WR775 VRD-MN2BD102J J AA 1 kohm,1/8WR776,777 VRD-ST2CD332J J AA 3.3 kohms,1/6WR778 VRD-ST2CD822J J AA 8.2 kohms,1/6WR780 VRD-MN2BD392J J AA 3.9 kohms,1/8WR782 VRD-ST2CD473J J AA 47 kohms,1/6WR783 VRD-ST2CD104J J AA 100 kohm,1/6WR785 VRD-ST2CD472J J AA 4.7 kohms,1/6WR786 VRD-ST2CD101J J AA 100 ohm,1/6WR791 VRD-MN2BD102J J AA 1 kohm,1/8WR792 VRD-ST2CD330J J AA 33 ohms,1/6WR800 VRD-RT2HD100J J AA 10 ohm,1/2WR901 VRD-ST2CD103J J AA 10 kohm,1/6WR902 VRD-RT2HD221J J AA 220 ohms,1/2WR903 VRD-ST2CD123J J AA 12 kohms,1/6WR904 VRD-RT2HD221J J AA 220 ohms,1/2WR905 VRD-ST2CD101J J AA 100 ohm,1/6WR906 VRD-ST2CD332J J AA 3.3 kohms,1/6WR908 VRD-ST2CD221J J AA 220 ohms,1/6WR921,922 VRD-ST2EE2R2J J AA 2.2 ohms,1/4W
OTHER CIRCUITRY PARTS
BI401/CNS401 QCNWN1380AWZZ J AF Connector Ass’y,6/6PinBI701/CNS701 QCNWN1381AWZZ J AL Connector Ass’y,15/15PinBI702/CNS702 QCNWN0907AWZZ J AC Connector Ass’y,8/12PinBIM5/CNS10/CNS5 QCNWN1184AWZZ J AL Connector Ass’y,6/10/2PinCNP1 92LCONE5P53253 J AB Plug,5PinCNP2 QCNCM705HAFZZ J AB Plug,8PinCNP3 92LCONE6P53253 J AC Plug,6PinCNP3A 92LCONE6P53254 J AC Plug,6PinCNP10 QCNCM705KAWZZ J AC Plug,10PinCNP11 QCNCM704FAWZZ J AC Plug,6PinCNP12 QCNCM704QAWZZ J AG Plug,15PinCNP301 92LCONE-3P5268 J AC Plug,3PinCNP501 92LCONE-3P5267 J AB Plug,3PinCNP502 92LCONE-7P5267 J AC Plug,7PinCNP901 QCNCM036BAWZZ J AC Plug,2PinCNP902 QCNCM035FAWZZ J AC Plug,6PinCNPM1 QCNCM932MAFZZ J AE Plug,12PinCNPM2 QCNCM030BAWZZ J AB Pin Header,2PinCNS1A/B QCNWN1181AWZZ J AK Connector Ass’y,5/5PinCNS2A/B QCNWN1182AWZZ J AH Connector Ass’y,8/8PinCNS3A/B QCNWN1183AWZZ J AG Connector Ass’y,6/6PinCNS101 QCNWN0895AWZZ J AE Connector Ass’y,3PinCNS102 QCNWN0896AWZZ J AG Connector Ass’y,8PinFL701 VVKSVA9MS13-1 J AZ FL DisplayFW601 QCNWN1249AWZZ J AE Flat Wire,5PinFW701 QCNWN1457AWZZ J AD Flat Wire,9PinFW703 QCNWN1458AWZZ J AD Flat Wire,10PinFW705 QCNWN0713AWZZ J AF Flat Wire,3PinFWM1 QCNWN1274AWZZ J AC Flat Cable,2PinFWM2 QCNWN0338AWZZ J AD Flat Cable,2Pin
JK601 QJAKM0004AWZZ J AK Jack,HeadphonesM1 92LMTR1854CASY J AS Motor with Chassis [Spindle]M2 92LMTR1854BASY J AP Motor with Gear [Sled]M3 92LMTR3022AS1 J AU Motor with Worm
[Turntable Up/Down/Loading]MM1 RMOTV0006AWM1 J AR Motor with Pulley [Tape]PHM1 VHPI31535CD-1 J AG Phote Interrupter
! RL901 RRLYD0011AWZZ J AE RelayRX701 VHLN63H380A-1 J AK Remote Sensor,N63H380ASO601 QTANA0412AWZZ J AF Terminal,Speaker
! SO901 QSOCA0209AWZZ J AH Socket,AC InputSOLM1 RPLU-0002AWZZ J AH Solenoid Ass’ySOLM2 RPLU-0002AWZZ J AH Solenoid Ass’ySW1 QSW-P0004AWZZ J AE Switch,Push Type [Open/Close]SW2 QSW-F0001AWZZ J AD Switch,Leaf/Skeleton Type
[Mecha Up]SW3 QSW-P0005AWZZ J AD Switch,Push Type [Disc Number]SW4 QSW-F9001AW01 J AD Switch,Push Type [Pickup In]SW701 92LSWICH-1401A J AC Switch,Key Type [Power]SW702 92LSWICH-1401A J AC Switch,Key Type [Clock]SW703 92LSWICH-1401A J AC Switch,Key Type [Timer/Sleep]SW707 92LSWICH-1401A J AC Switch,Key Type [Disc Skip]SW708 92LSWICH-1401A J AC Switch,Key Type [Open/Close]SW709 92LSWICH-1401A J AC Switch,Key Type [Rewind]SW710 92LSWICH-1401A J AC Switch,Key Type [Record/Pause]SW711 92LSWICH-1401A J AC Switch,Key Type [Memory/Set]SW712 92LSWICH-1401A J AC Switch,Key Type [Stop]SW713 92LSWICH-1401A J AC Switch,Key Type [Tuner/Band]SW714 92LSWICH-1401A J AC Switch,Key Type [Tape]SW715 92LSWICH-1401A J AC Switch,Key Type [CD]SW716 92LSWICH-1401A J AC Switch,Key Type [Fast Forward]SW717 92LSWICH-1401A J AC Switch,Key Type [Tuning Up]SW718 92LSWICH-1401A J AC Switch,Key Type [Tuning Down]SW719 92LSWICH-1401A J AC Switch,Key Type [Play]SW720 92LSWICH-1401A J AC Switch,Key Type [Volume Down]SW721 92LSWICH-1401A J AC Switch,Key Type [Volume Up]SW722 92LSWICH-1401A J AC Switch,Key Type
[X-BASS/Demo]SWM3 92LM-SW1676A J AC Switch,Leaf Type [Fool Proof]SWM4 QSW-F9003AWZZ J AG Switch,Leaf Type [F.A.S.]SWM5 92LM-SW1658A J AB Switch,Leaf Type [CAM]
CD MECHANISM PARTS
301 NGERH0011AWZZ J AC Gear,Middle302 NGERH0012AWZZ J AC Gear,Drive303 MLEVP0080AWZZ J AC Rail,Guide304 NSFTM0002AWFW J AE Shaft,Guide305 92LMCUSN1524A J AD Cushion
! 306 92LHPC1MASY J BG Pickup Unit Ass’y306- 1 ———— — Pickup Unit
(Not Replacement Item)306- 2 NGERH0010AWZZ J AB Gear,Rack306- 3 MSPRC0961AFZZ J AA Spring,Rack701 XBSSD26P06000 J AA Screw,ø2.6×6mm702 XHBSD20P05000 J AA Screw,ø2×5mm703 XBBSD20P03000 J AA Screw,ø2×3mm704 LX-WZ1070AFZZ J AA Washer,ø1.5×ø3.8×0.25mmM1 92LMTR1854CASY J AS Motor with Chassis [Spindle]M2 92LMTR1854BASY J AP Motor with Gear [Sled]SW4 QSW-F9001AW01 J AD Switch,Push Type [Pickup In]
CABINET PARTS
201 92LCAB3041AS1 J BA Front Panel Ass’y [CD-C606]201 92LCAB3042AS1 J AZ Front Panel Ass’y [CD-C1900]201- 1 ———— — Front Panel
(Not Replacement Item)201- 2 HDECQ0459AWSA J AH Panel,Display [CD-C606]201- 2 HDECQ0468AWSA J AH Panel,Display [CD-C1900]201- 3 HDECQ0460AWSA J AH Panel,Operation201- 4 HDECQ0461AWSA J AC Ring,Operation201- 5 HDECQ0462AWSA J AC Cap,Operation Center201- 6 HDECQ0469AWSA J AE Panel,Center Cap201- 7 JKNBZ0603AWSA J AG Button,Stop/Play/Repeat201- 8 JKNBZ0604AWSA J AF Button,Function Selector201- 9 JKNBZ0605AWSA J AF Button,Volume Up/Down201-10 JKNBZ0606AWSA J AE Button,Power201-11 JKNBZ0607AWSA J AE Button,X-BASS/Demo201-12 JKNBZ0608AWSA J AC Button,Timer/Sleep/Clock201-13 JKNBZ0610AWSA J AM Button,Disc Skip/Open/Close201-14 PCUSG0022AWZZ J AB Cushion,Leg
PRICERANK
DESCRIPTIONNO. PARTS CODE NO. PARTS CODE PRICERANK DESCRIPTION
CD-C606/1900,CP-C606/1900
– 5 –
202 92LCAB3041BS1 J AM Side Panel Ass’y,Left202- 1 GITAS0062AWSA J AK Side Panel,Left202- 2 PCUSG0022AWZZ J AB Cushion,Leg203 92LCAB3041CS1 J AM Side Panel Ass’y,Right203- 1 GITAS0063AWSA J AK Side Panel,Right203- 2 PCUSG0022AWZZ J AB Cushion,Leg204 92LCOV3022AS1 J AM CD Tray Cover Ass’y204- 1 GCOVA1223AWSA J AG Cover,CD Tray204- 2 GCOVA1224AWSA J AE Cover,CD Tray Panel,Left204- 3 GCOVA1225AWSA J AE Cover,CD Tray Panel,Right204- 4 92LBADGE1671A J AC Badge,SHARP205 GITAR0442AWSA J AH Back Board [CD-C606 for
U.S.A./Central America]205 GITAR0444AWSA J AH Back Board
[CD-C606 for Canada]205 GITAR0456AWSA J Back Board [CD-C1900 for
U.S.A./Central America]205 GITAR0457AWSA J Back Board
[CD-C1900 for Canada]205 GITAR0458AWSA J Back Board
[CD-C1900 for Mexico]206 GDORF0072AWSA J AK Cassette Holder,Tape 1207 GDORF0073AWSA J AK Cassette Holder,Tape 2208 HDECQ0463AWSA J AE Panel,Cassette Holder,Tape 1209 HDECQ0464AWSA J AE Panel,Cassette Holder,Tape 2210 LANGK0170AWFW J AC Bracket,Headphone Support211 LANGT0049AWFW J AK Bracket,Heat Sink212 LCHSM0086AWSA J AM Main Chassis213 LHLDZ1087AWSA J AC Holder,FL Display214 MLIFP0003AWZZ J AE Damper,Cassette Holder215 MSPRD0092AWFJ J AB Spring,Cassette Holder Up,
Tape 1216 MSPRD0093AWFJ J AB Spring,Cassette Holder Up,
Tape 2218 PRDAR0138AWFW J AH Heat Sink,Main219 92LRDAT-1468B J AE Heat Sink,Sub220 92LMECHA2823A J BL Tape Mechanism Ass’y220- 1(MM1) RMOTV0006AWM1 J AR Motor with Pulley [Tape]220- 2 NBLTK0011AWZZ J AC Belt,Main [Tape 1]220- 3 NBLTK0012AWZZ J AB Belt,Main [Tape 2]220- 4 NBLTK0030AWZZ J AC Belt,Sub220- 5 NROLY0002AWZZ J AF Pinch Roller220- 6 92LMRPH1746A J AM Head,Record/Playback
[Tape 1/Tape 2]220- 7 RHEDA0001AWZZ J AG Head,Erase [Tape 2]220- 8(SWM3) 92LM-SW1676A J AC Switch,Leaf Type [Fool Proof]220- 9(SWM4) QSW-F9003AWZZ J AG Switch,Leaf Type [F.A.S.]220-10(SWM5) 92LM-SW1658A J AB Switch,Leaf Type [CAM]221 92LLABL372C J AB Label,Serial No.
[For Canada Only]222 92LN-BAND1318A J AA Nylon Band,80mm223 GCAB-1044AWSA J AM CD Player Base224 GCAB-1052AWSA J AP Top Cabinet225 LANGF0032AWZZ J AC Support,Turntable Lock Lever226 LCHSZ0010AWZZ J AM Chassis,Loading227 LCHSZ0011AWZZ J AG Chassis,CD Mechanism228 92LHOLD3022AS1 J AB Stabilizer Ass’y228- 1 ———— — Stabilizer
(Not Replacement Item)228- 2 PMAGF0001AWZZ J AF Magnet,Stabilizer228- 3 92LSUPT1749D J AA Support,Stabilizer Magnet229 LHLDZ1140AWZZ J AB Guide230 LHLDZ1141AWZZ J AB Support,Pitch231 LHLDZ1204AWSA J AD Support,Stabilizer232 MLEVP0066AWZZ J AE Lever,Shift233 MLEVP0067AWZZ J AC Lever,Lock234 MLEVP0068AWZZ J AB Lever,Change235 MLEVP0070AWZZ J AB Lever,Turntable Lock236 MSPRC0020AWFJ J AB Spring,Turntable Lock Lever237 MSPRC0024AWFW J AB Spring,Solenoid238 MSPRD0044AWFJ J AB Spring,Lock Lever239 NBLTK0033AWZZ J AC Belt,Drive240 NGERH0064AWZZ J AD Gear,Cam241 NGERH0065AWZZ J AB Gear,Turntable242 NGERK0003AWZZ J AC Gear,Drive243 NGERK0004AWZZ J AB Gear,Bevel244 NGERK0005AWZZ J AB Gear,Loading245 NGERW0006AWZZ J AC Gear,Worm Wheel246 NPLYD0002AWZZ J AC Pulley247 NROLP0009AWZZ J AB Roller248 NTNT-0018AWSA J AK Turntable249 PCOVZ1013AWZZ J AB Cover,Wire
250 TLABN0086AWZZ J AB Label,Production SER.No.[U.S.A./Central America Only]
! 251 QLUGP0001AWZZ J AC Lug252 PCUSG0022AWZZ J AB Cushion253 LHLDZ1230AWZZ J AC Holder,LED602 XBPSD26P05JSO J AB Screw,ø2.6×5mm603 XEBSD26P12000 J AA Screw,ø2.6×12mm604 XEBSD30P10000 J AA Screw,ø3×10mm605 XEBSD30P12000 J AA Screw,ø3×12mm606 XEBSF30P12000 J AA Screw,ø3×12mm607 XESSD30P10000 J AA Screw,ø3×10mm608 XJBSD30P08000 J AA Screw,ø3×8mm609 XJBSD30P10000 J AA Screw,ø3×10mm610 XJBSF30P08000 J AA Screw,ø3×8mm611 XJSSF30P10000 J AA Screw,ø3×10mm612 XWHJZ62-09510 J AB Washer,ø6.2×ø10×0.9mm614 LX-EZ0005AWFD J AA Screw,Special615 LX-JZ0002AWFD J AA Screw,ø3×10mm616 LX-JZ0004AWFD J AA Screw,ø3×12mm618 LX-TZ0019AFZZ J AB Screw,Special
PACKING PARTS (For Canada/Central America)
SPAKA0212AWZZ J AL Packing Add.,Left/RightSPAKC0746AWZZ J Packing Case
[CD-C606 for Central America]SPAKC0749AWZZ J Packing Case
[CD-C606 for Canada]SPAKC0751AWZZ J AR Packing Case
[CD-C1900 for Central America]SPAKC0752AWZZ J AR Packing Case
[CD-C1900 for Canada]SPAKP0013AWZZ1 J AC Polyethylene Bag,UnitTLABR1027AWZZ J AB Label,Bar Code [CD-C1900 for
Central America Only]TLABR1028AWZZ J AB Label,Bar Code [CD-C606 for
Central America Only]92LBAG1460C1 J AB Polyethylene Bag,Accessories
ACCESSORIES
! QACCD0015AW00 J AM AC Power Supply Cord[For Canada]
! QACCD0020AWZZ J AN AC Power Supply Cord[For U.S.A./Central America]
QANTL0007AWZZ J AK AM/FM Loop AntennaTINSE0243AWZZ J AE Operation Manual
[CD-C606 for U.S.A.]TINSE0244AWZZ J AE Operation Manual
[CD-C1900 for U.S.A.]TINSK0083AWZZ J AH Operation Manual
[CD-C606 for Canada]TINSK0084AWZZ J AE Operation Manual
[CD-C1900 for Canada]TINSZ0409AWZZ J AB Quick Guide [CD-C606 for
U.S.A./Central America Only]TINSZ0410AWZZ J AE Operation Manual
[CD-C1900 for Mexico]TINSZ0411AWZZ J AB Quick Guide [CD-C1900 for
U.S.A./Central America Only]TLABZ0527AWZZ J AB Label,Feature,Unit,Tape 1TLABZ0528AWZZ J AB Label,Feature,Unit,Tape 2RRMCG0179AWSA J AS Remote ControlGFTAB1022AWSA J Battery Lid,Remote Control
PWB-B 92LPWB3041CDUS J — CD Servo [CD-C606]PWB-B 92LPWB3042CDUS J — CD Servo [CD-C1900]PWB-C QPWBF0027AWZZ J AD CD Motor (PWB Only)PWB-D QPWBF0341AWZZ J AB Tray Motor (PWB Only)PWB-E QPWBF0106AWZZ J AF Tape Mechanism (PWB Only)
NO. PRICERANK DESCRIPTIONPARTS CODENO. PARTS CODE PRICE
RANK DESCRIPTION
CD-C606/1900,CP-C606/1900
– 6 –
CP-C606/1900
OTHER SERVICE PARTS
UDSKA0004AFZZ J AZ CD Pickup Lens Cleaner Disc
SPEAKER BOX PARTS
701 92LJ1911A J AZ Net Frame Ass’y [For CP-C606]701 92LJ1916A J AU Net Frame Ass’y [For CP-C1900]702 92L8530C J Speaker Box Ass’y
[For CP-C606]702 92L8537C J Speaker Box Ass’y
[For CP-C1900]703 92LD4680A J Cord,Speaker704 92LF1377A J AC Screw,ø3.5×13mm705 92LP5870 J AC Label,Specifications
[For CP-C606]705 92LP5871 J AB Label,Specifications
[For CP-C1900]706 92LJ1912A J AX Panel,Duct707 92LJ9797C J AE Port CushionSP1,2 VSP0010PBY38A J Speaker,WooferSP3,4 92LC2022DG J AG Speaker,Super Tweeter