8/2/2019 Shan Mini Project
1/20
AUTOMATIC REVERSE BRAKINGSYSTEM USING IR SENSOR
Team Members
1. D.Sathya Prakash (09ME36)2. R.Shanmugam (09ME37)
3. M.Siva Kumar (09ME38)
Guided by,
Mr.M.Deepakumaran., M.E.
8/2/2019 Shan Mini Project
2/20
ABSTRACTThe aim is to design a automatic reverse braking system For a
purpose of prevent collision between the vehicle and any objects while
moving in the reverse path.
The main advantage of this is there is no need of manual power if any
objects in the reverse path the sensor senses the object and the brake is
applied automatically.
The high quality IR sensor is used to sense the objects on reverse
path. The design is based on intelligent electronically controlled automotive
braking system is called INTELLIGENT REVERSE BRAKING
SYSTEM.
Sensor Operated Pneumatic Brake is consists of IR transmitter and
Receiver circuit, Control Unit, Pneumatic breaking system. The IR sensor
is used to detect the obstacle. There is any obstacle in the path, the IR
sensor senses the obstacle and giving the control signal to the breaking
system.
8/2/2019 Shan Mini Project
3/20
INTRODUCTION
We have pleasure in introducing our new project INTELLIGENTBRAKING SYSTEM, which is fully equipped by IR sensors circuit and
pneumatic breaking circuit. It is a genuine project which is fully equipped and
designed for automobile vehicles. This forms an integral part of best quality.
This product underwent strenuous test in our automobile vehicles and it is good.
The PNEUMATIC BRAKING CIRCUIT can stop the vehicle within
2 to 3 seconds running at a speed of 50KM.The intelligent breaking system
is a fully automation project.
This is an ear of automation where it is broadly defined as replacement of
manual effort by mechanical power in all degrees of automation. The operation
remains an essential part of the system although with changing demands on
physical input as the degree of mechanization is increased.
8/2/2019 Shan Mini Project
4/20
NEED FOR AUTOMATION1. To achieve mass production2. To reduce man power
3. To increase the efficiency of the plant
4. To reduce the work load
5. To reduce the production cost
6. To reduce the production time
7. To reduce the material handling
8. To reduce the fatigue of workers
9. To achieve good product quality
10. Less maintenance
8/2/2019 Shan Mini Project
5/20
BASIC LAYOUT
8/2/2019 Shan Mini Project
6/20
TYPES OF BRAKING
The brakes for automotive use may be classified
according the following considerations.
1. PURPOSE
2. LOCATION
3. CONSTRUCTION
4. METHOD OF ACTUATION
5. EXTRA BRAKING EFFORT
8/2/2019 Shan Mini Project
7/20
MECHANICAL BRAKE
8/2/2019 Shan Mini Project
8/20
HYDRAULIC BRAKE
8/2/2019 Shan Mini Project
9/20
AIR BRAKE
8/2/2019 Shan Mini Project
10/20
REGENERATIVE BRAKE
8/2/2019 Shan Mini Project
11/20
BRAKING SYSTEM USED IN OUR
PROJECT
Air Brake System
An air brake system uses compressed air to apply the brakes.Air under pressure can be conveniently stored and carried throughlines or tubes.
Reason for Selection of Air Brake
Free resources so no refilling or changing required.
Air pressure is quick to act and hence air brakes are immediate.
The pressure of brake applied is directly proportional to the air pressure.
A little feather touch would apply the same pressure.
Air brakes can effectively stop loads of over 14 tons.
8/2/2019 Shan Mini Project
12/20
COMPONENTS USED IN AIR BRAKE
1. PNEUMATIC SINGLE ACTING CYLINDER
PISTON
PISTON ROD
CYLINDER COVER PLATES
2. SOLENOID VALVE
3. FLOW CONTROL VALVE
8/2/2019 Shan Mini Project
13/20
IR SENSOR
IR Transmitter
The IR transmitting circuit is used in many projects. The IR transmittersends 40 kHz (frequency can be adjusted) carrier under 555 timer control. IRcarriers at around 40 kHz carrier frequencies are widely used in TV remotecontrolling and ICs for receiving these signals are quite easily available.
IR Receiver
The transmitted signal reflected by the obstacle and the IR receivercircuit receives the signal and giving control signal to the control unit. Thecontrol unit activates the pneumatic breaking system, so that break was applied.
8/2/2019 Shan Mini Project
14/20
WORKING OPERATION
3/2 SINGLE ACTING SOLENOID (OR) CUT OFF VALVE
This valve is used to speed up the piston movement and also it acts as
a one way restriction valve which means that the air can pass through only
one way and it cant return back. By using this valve the time consumption
is reduced because of the faster movement of the piston.
IR SENSOR UNIT
The IR transmitter and IR receiver circuit is used to sense the
obstacle. It is fixed to the back side of the frame stand with a suitable
arrangement. The pneumatic cylinder is controlled by the flow controlvalve, single acting solenoid valve and control unit.
8/2/2019 Shan Mini Project
15/20
AT NORMAL CONDITION
The IR transmitter sensor is transmitting the infrared rays with the
help of IC 555 timer circuit. These infrared rays are received by the IR
receiver sensor. The transistor T1, T2 and T3 are used as an
amplifier section. At normal condition transistor T5 is OFF conditions. At
that time relay is OFF, so that the vehicle running continuously.
AT OBSTACLE CONDITION
At obstacle conditions the IR transmitter and IR receiver, the
resistance across the transmitter and receiver is high due to the non -conductivity of the IR waves. So the output of transistor T5 goes from OFF
condition ON stage. In that time the relay is ON position. In that time, the
solenoid valve is on so that the vehicle stops.
8/2/2019 Shan Mini Project
16/20
The important components of our project are
1. IR Transmitter2. IR Receiver
3. Control Unit with Power Supply
4. Solenoid Valves
5. Flow Control Valve
The IR Transmitter circuit is to transmit the infra red rays. If anyobstacle is there in a path, the infra red rays reflected. This reflected infra redrays are received by the receiver circuit is called IR Receiver.
The IR Receiver circuit receives the reflected IR rays and giving thecontrol signal to the control circuit. The control circuit is used to activate thesolenoid valve. The operating principle of solenoid valve is on so that thevehicle stops.
8/2/2019 Shan Mini Project
17/20
ADVANTAGES
1. Brake cost will be less.
2. Free from wear adjustment.
3. Less power consumption.
4. Less skill technicians is sufficient to operate.
5. It gives simplified very operation.
6. Installation is simplified very much.
7. To avoid other burnable interactions viz. (Diaphragm) is not used.
8. Less time and more profit.
8/2/2019 Shan Mini Project
18/20
DISADVANTAGES
1. Excessive use of brake results in overheating and leads to brake fade.
Brake fade results from excessive heat causing chemical changes in the
brake lining that reduces friction and causes expansion of the brake drums.
2. Failure of IR sensor or control unit is not indicated
3. It is not effective in round turn or turning more than 30 degree.
4. Excessive Oil and Water Present in the Air Brake System causes the
Reservoirs to corrode if not drained often enough.
8/2/2019 Shan Mini Project
19/20
APPLICATION
1. For automobile application
Air brakes are used on heavy trucks.
Agricultural tractor and trailer.
Forestry vehicles.
City Works vehicles.
2. Industrial application.
8/2/2019 Shan Mini Project
20/20