Setup of AWY_2 0 4

All Rights Reserved © Alcatel-Lucent 2006, #####

9400 AWYversion 2.0.4

Name of Presenter : Abdel Aziz Sayed

Date (12, 2007)

All Rights Reserved © Alcatel-Lucent 2006, #####2 | Presentation Title | Month 2006

Agenda

1. AWY 2.0.4 SOFTWARE

2. AWY 2.0.4 SUPPORTED HARDWARE

3. AWY 2.0.4 NEW FEATURES

4. CORRECTION DONE FROM PREVIOUS RELEASE

5. AWY 2.0.4 Setup

6. TCO User Guide

7. FLASH CARD UPGRADE


1 AWY 2.0.4 SOFTWARE


1320 CT REQUIRMENT

This section describes the recommended minimum HW/SW requirements of the ECT application for a recognized level of application performances.

HW CONFIGURATION

.CPU : Pentium III 850 MHz

.RAM : 512 Mbytes mandatory

.HARD DISK SPACE : 4 Gbyte

.DISPLAY RESOLUTION : 1024 x 768 pixel

.CD-ROM DRIVE : 24x

.PRIMARY INTERFACE : serial port RS-232-c 9.6 to 57.6 Kbps

.OPTIONAL INTERFACE : Ethernet card 10/100 Mbps


Windows versions

.Windows 2000 till sp4 included

.Windows XP professional Edition (till sp2 included). It is mandatory to de-active the firewall installed

Additional requirements

.Netscape communicator or Ms Internet Explorer 4.x or higher

.Java 2 Run time Environment versions from 1.4.2-12

NOTE: Each specific Java version could require minimal Windows sp installation


2 AWY 2.0.4 SUPPORTED HARDWARE


2.0.4 supported hardware

.IDU 32 Mb (16E1)

.Up to 16E1/1E3

.1+0/1+1/HSB

.2xEthernet ports

.PSU 48 and 24 VDC

.Hitless Switch protection

.ATPC

.Support of all available frequency bands

.ODU 64Mb V1 (32E1)

.ODU 32Mb V1 (16E1)


3 AWY 2.0.4 NEW FEATURES


· Introduction of TCO : suite of features based on a web browser (Pre-Provisioning Tool and Set-up Tool)

The purpose of the Pre-provisioning Tool is to prepare the configuration for one or

several sites (identified by a site name) with no need to have the equipment(s) physically

connected. This allows a stand-alone configuration preparation e.g. in back office.

The Set-up tool allowing the user to apply in the element, the prepared configuration.

At the present time, TCO, and particularly configuration settings via TCO are recommended:- For people who are not familiar with 1320CT. For a first installation in order to allow antenna alignment.

o This applies particularly for installation teams if commissioner is not present on site.


4 CORRECTION DONE FROM PREVIOUS RELEASE


.Improvements in craft terminal supervision. A polling time applied at application level allow the control of the communication with the IDU. For instance when IDU has to reset because of some configuration changes the communication is automatically restarted. .In case of disconnection of E3/DS3 input on active board, LOS (loss of signal) alarm displayed but EPs dose not switch, this is corrected in release R2.0.4 and new plug in board..Additional feature named (NAT yes/no) to allow the network management through routers using NAT protocol. In this case the NMS IP address recognition is inhibited..Support of multi-shifter ODU’s able to operate with several shifters described in shifter list. Example: 18 GHz ODU able to operate either with 1008 MHz or 1010 MHz..Data Ethernet feature: Auto-negotiation and rate status..Flash card corrupted after repeated switch off/on. Awy 2.0.4 solve this debug


5 AWY 2.0.4 SETUP


1320 CT Setup

Put REGAWY_204 INTO CD ROM

IT WILL START AUTO RUN


SELECT ADVANCED SETTING


INSTALL JAVA JRE PACKET


PRESS RUN THEN INSTALL SERIAL-F-INTERFACE DRIVER AT THE END FILL THE LOWER LAYER SETTING BY 000000000000 IN

SYSTEM IDENTIFIER , SEREIAL PORT IN SUB-NETWORK TYPE, COM NUMBER IN SERIAL PORT AND DEFAULT IN PORT SPEED.

NOTE: If PC hasn't serial interface you must plug USB-Serial converter.



After lower layer you must add Alcatel lower layer network card

From control panel add new hard ware then press next


Select add new hardware


Select network adapters


Select have a disk then browse c:\windows\system32\driver\llmannic\oemsetup.inf



From network connection

Select Alcatel lower layer network card


Check internet protocol (TCP/IP) only


Put ip address and subnet mask


Disable firewall


Complete installation by install 1320 ct package installation


6 TCO User Guide


Put REGAWY_204 INTO CD ROM

IT WILL START AUTO RUN - select pre-provisioning tool


Press create configuration


fill required parameter and press next




















press save as to save the configure file to your pc disk


7FLASH CARD UPGRADE


1 ) Launch the CT by:

–TCO Suite Main Menu Þ Operational & Maintenance

or:

–Start Þ 1320CT

2 ) On NES (Network Element Synthesis) screen that opens, from the Supervision pull down menu select the File Administration and then the Software Administration option, as shown

in Fig.


3 ) In the screen that opens (Fig. below) click on Install


4 ) In the screen that opens (Fig. 316. below is an example) select the directory where the NEAll rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel–Lucent

software package is installed:

Alcatel / JUSMw V.x.x.x / ect / swdw / <equipment name> / <version> / <descriptor file> (*) (*)the 9400AWY equipment name is “R94AWY” ;

the version is that you want;

the descriptor file has always the extension “.DSC”.

N.B. The NE software package can also be selected from the CD–ROM used for the installation of the NE software. In this case, after inserting the CD–ROM in the driver, choose the following:

ect / swdw / <equipment name> / <version> / <descriptor file>



5 ) On last screen (containing the “.DSC” file), click on Open to activate the installation of theAll rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel–Lucent

selected“.DSC” file. At the end of the process, a confirmation message is displayed:

6 ) At this point the NE Software Package is installed and available to be downloaded on theNetwork Elements (as described in chapter 6–8 on page 663).

Such availability can be verified (as shown in Fig. here below) operating in the Network Element Synthesis screen (Fig. 314. on page 499), selecting, from the Supervision pull down menu, the File

Administration and then the Software Administration option


SW DOWNLOADAll rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel–Lucent

4–13.1 Server Access Configuration

This menu allows to configure the FTP server to be used to download the SWP to the NE.

N.B. The complete procedure to download the SWP to the NE


User Id and Password are the login information to access the FTP server. In the Address field write the IP address of the FTP server.

In the Port field write the port to be used and in the Root Directory field write the directory into which the software has been downloaded.

By clicking on the Use System Default button a screen will appear showing the default configuration. The CT is the default FTP server with the following parameters:

–User Id: ftp

–Password: ftp

–Address: IP address of the F interface or IP address of the Ethernet interface, if present.

–Port: 15,000

N.B. the System Default can be changed by writing different values in the fields and then by clicking on button OK.


Init SW DownloadAll rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel–Lucent

N.B. The first part of the procedure to download the SW to the NE is shown Through this menu software is downloaded to the NE in order to upgrade the NE software version.

To start download select the desired software version and click on the Init download button.

N.B. This screen displays the software packages previously stored through the menu Supervision

–> Files Administration –> Software Administration available in the NES menu.

The Forced check box can be used to force download (i.e. the complete description file is downloaded

to the NE).

If the Forced download is not selected, the system shall first proceed to compare the software to be downloaded with the software present in the NE. Then only the differences are downloaded.


SW StatusAll rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel–Lucent

This menu allows to display the information of the software installed in the NE.

The following information is displayed:

–Name: software name

–Version: software version

–Operational state: enabled or disabled

–Current status: committed or standby. The committed status refers to the software currently in use.

By clicking on the Software Units Status button the screen of Fig. 263. below opens, giving additional information on the software package.

Setup of AWY_2 0 4

Documents