,,,,# FILE NO. SERVICE MANUAL Colour Television Product Code: 111338815 Original Version Chassis Series: AC2-A ~ Give complete “SERVICE REF. NO.” for parts order or servicing It is shown on the rating plate at the cabinet back of the unit. This T.V. receiver will not work properly in foreign countries where the television transmission system and power source dif- fer from the design specifications. Refer to the specification table. — Specifications Power Source .........AC220-240V, 50 Hz. Colour System ........ PAL (AV Input: PAUNTSC/NTSC4.43) - Television System ...... B/G Channel Coverage .....VHF: 1-11 UHF: 21-69 CATV S1-S41 , X, Y, Z, Z+l, Z+2 VldeolF .............38.9 MHz SoundlF ............33.4MHz Aerial Input Impedance . .75Q Ext. Terminals Video inputs: Phono jack X 3(1 Vp -p, 75f2) Audio inputs: Phono jack (R/L) X 3(436mVrms, more than 40KQ) Video monitor outputs: Phono jack X 1(lVp - p, 75Q) Audio monitor outputs: Phono jack(FUL) x 1(436mVrms, less than 600$2) Headphone jack Mini stereo jack X 1 Sound Output ......... 7.5W+7.5W Dimensions .......... 770(W) x 590(H) x 495(D)mm Weight ..............approx.39.9 Kg Model No. CP29ST3T (New Zealand) service Ref. No. CP29ST3T~ Specifications subject to change without notice. -b F2DT REFERENCE NO. SM510235
37
Embed
SERVICE MANUAL Colour Television Model No. CP29ST3Tcncms.com.au/SANYO-SMs/Consumer-Electronics/CRT-Television/cp2… · FILE NO. SERVICE MANUAL Colour Television Product Code: 111338815
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
,,,,#
FILE NO.
SERVICE MANUAL Colour Television
Product Code: 111338815
Original Version
Chassis Series: AC2-A
~
Give complete “SERVICE REF. NO.” forparts order or servicing It is shown on therating plate at the cabinet back of the unit.
This T.V. receiver will not work properly inforeign countries where the televisiontransmission system and power source dif-fer from the design specifications. Refer tothe specification table.
Audio inputs: Phono jack (R/L) X 3(436mVrms, more than 40KQ)
Video monitor outputs: Phono jack X 1(lVp - p, 75Q)Audio monitor outputs: Phono jack(FUL) x 1(436mVrms, less than 600$2)Headphone jack Mini stereo jack X 1
thesametypeas the original including suffix letter. Excessive high voltage may produce potentially hazardous
-RADIATION.TO avoid such hazards, the high voltage must be maintained within specified limit. Refer tothisser-
vice manual, high voltage adjustment for specific high voltage limit. lfhigh voltage exceeds specified Iimits, take
necessary corrective action.Carefully followthe instructions for+ Bl volt power supply adjustment, and high volt-
age checkto maintain the high voltage within the specified limits.
PRODUCT SAFETY NOTICE
Product safety should be considered when a component replacement is made in any area of a receiver.
Components indicated by mark ~ in the parts list and the schematic diagram designate components in which
safety can be of special significance. It is particularly recommended that only parts designated on the parts list
in this manual be used for component replacement designated by mark ~ . No deviations from resistance
wattage or voltage ratings may be made for replacement items designated by mark ~ .
-2-
Chassis Block DiagramsFollowing diagrams show the fundamental block diagrams for AC2 chassis and there--fore differ slightly from actual diagram of each TV set.
U _ x133= ●Q133 J~24f10 “-’--’” T&REARTERMINALUNIT
C471
HOF
C482
‘T
o 0C297
00C515 C521 IC501VERT.
Q.Q540
Q4310C514,, ?C434
I \FOCUSADJ. ‘+B POWERSUPPLYCHECK—
S6REENVR
~_jNTALWIDTH)@J.
Protection CircuitThis TV set has a built-in power supply protection circuit.It is provided to protect the TV set in case of a power supply circuit malfunctions. When something abnormalityoccurs during TV reception, the TV set goes to the stand-by mode.
When an abnormality occurs during TV reception, it causes pin 24 of the CPU to go continually Low(less than0.75V) for about one second. The CPU detects that this has occurred and outputs the signal from pin 15 toswitch off the power supply lines.
H Releasing the protective circuit and restoring power supply
To release the protective circuit and restore power supply, turn the power to the TV set OFF and then ON againvia either the main power switch or the ON-OFF button on the remote control. This will work only if the powersupply trouble was temporary. If there is permanent trouble such as a damaged circuit, power cannot berestored and the circuit will have to be repaired.
-1o-
Service Adjustments with Replacing Memory IC(IC802)
Note: The CPU (IC801 ) and memory IC (IC802) store the service adjustments data and controls data for each circuit.When the Memory IC(IC802) is replaced, some of the service adjustments should be readjusted to obtain thebest performance. The necessary service adjustments are carried out by using the RC handset. Please setup the TV set with following steps [1] to [3].
[1] Initializing Procedure1.Put a new memory IC.2. Turn on the TV set.3. Press and hold the [TV/AV] buttonon the TV set morethan 2 seconds. The following picture appears on the screen.
CLR
AV
4. Press the [FUNCTION] button on the TV set while the above On-Screen Display is still on the screen. The followingpicture appears on the screen.
1
AUTO
This completes the initialization of memory IC.
Following shows the initialized contents of memory data by this procedure.- Plug & play : No executed- Inhibit data : Cancelled
L - Ch skip data : Cancelled- Set volume control value to 10/63 steps.- Set all of control values in PERSONAL mode to initial value shown in below table.
Note: When the memory IC replaced, the CPU writes the controls initial value to tlmemory IC as shown in below table.
Controls PERSONAL DYNAMIC NATURAL SOFT
COLOUR 31/63 35/63 31/63 31/63
BRIGHT 31/63 33/63 31/63 34/63
CONTRAST 55/63 63/63 55/63 26/63
TINT 31/63 31 /63 31/63 31 /63
SHARPNESS 31/63 48/63 31 /63 24/63
BASS*1 7/1 4 7/1 4 7/1 4 7/1 4
TREBLE*1 7/1 4 7/1 4 7/1 4 7/1 4
BALANCE*1 7/1 4 7/1 4 7/1 4 7114
Note: ●1 Only available for Stereo decoder equipped model‘L I
replaced
GAME
23/63
26/63
20/63
31/63
10/63
7/1 4
7/1 4
7/1 4
-11-
[2] Required Service AdjustmentsReadjust the following service adjustments.
Adjustments Service Mode No. & ItemHorizontal centre adjustment Item 01, H-P
06 Vco 128 0-255 VCO (AFT) adjustment07 SIF o 0-3 SIF VCO adjustment08 SELF o 0-15 SELF-adjusting09 DLT 2 0-3 DL-time adjustment10 DLF o 0, 1 DL-fine adjustment11 B-ST o 0, 1 Black stretch on/off setting12 ABCL 1 0, 1 ABCL adjustment13 AB-G o 0, 1 ABCL gain adjustment
14 TRAP 3 0-3 Trap frequency adjustment
15 WBK o 0, 1 White back setting16 BBK o 0, 1 Blue back setting17 AFCG 2 0-2 AFC gain adjustment18 RBI o 0-255 Red bias adjustment19 GBI o 0-255 Green bias adjustment
20 BBI o 0-255 Blue bias adjustment21 RD 64 0-127 Red drive adjustment22 BD 64 0-127 Blue drive adjustment23 DRV -- . . White balance adjustment
3Grey scale adjustment
24 -- -- -. Y-cut setting
Notes:+ The initial value that the CPU writes down the CPU ROM data to the memory when replaced the memory IC. TV set
may not operate correctly with this initial value. It is required to set up the fine adjustment for service adjustmentsdescribed in the above.
—
-12-
L [Entering to Service Mode]1.Press and hold the [FUNCTION] button on the TV set and press the [1]button on the remote control handset.
Following setting setting items appears on the screen.
Disdav for [AGCI AGC adjustment..-1
/
0010010
05 AGC 63
/ \ \Item No. Item Data value
~ Read Status
Display for [DRV] White balance adjustment
I [
~ Read Status
0010010
23 DRV R 64 B 64%
/ \Item No.
\Item Data value for Red
Data value for Blue
2. Select item by pressing the [OFF TIMER] or [MUTE] button on the remote control handset.3. Adjust value by pressing the [VOLUME +] or [VOLUME - ] button on the remote control handset.
To return to normal TV mode, press the [FUNCTION] button on the TV set or on the remote control handset.
[3] Special Function Setting1.Following items should be set up in the special function mode, please refer to “Special Functions” on page 15 forL
actual setting up.
- Volume Lock : OFF- Tuning Lock : OFF- AV Start : OFF- Blue Back : OFF- Music Mode : OFF
2. Confirm following system setting by pressing [RECALL] button on the remote control handset.
- Colour system : AUTO- SIF system : s-1
●Note: There may be not available the above function depending on the specification of TV set.
L
-13-
Service Mode Adjustments
ADJUSTMENT-1Following adjustments should be carried out when the memory IC is replaced. How to enter the service mode andadjust values, please refer to” Entering to Service mode” on page 12.
(1) Receive the monochrome circular pattern.(2) Set the brightness and contrast to normal.(3) Select [H-P] in the service mode.(4) Change value to be optimum horizontal centre position.(5) Exit from the service mode.
QHorizontal centre
o
(1) Receive the monochrome circular pattern.(2) Set the brightness and contrast to normal.(3) Select [V-P] in the service mode.(4) Change value to be optimum vertical centre position.(5) Exit from the service mode.
Vertical centre
(1) Receive the monochrome circular pattern.(2) Set the brightness and contrast to normal.(3) Select [V-S] in the service mode.(4) Change value to be optimum vertical size.
(5) Exit from the service morje.
Vertical size
(1) Receive the monochrome circular pattern.(2) Set the brightness and contrast to normal.(3) Select [OSD] in the service mode.(4) Change value to be proper OSD position.(5) Exit from the service mode.
NOTE: Do not attempt this adjustment with weak signal.(1) Tune the receiver to most clearest (or strongest) VHF
station in your area. Set the brightness and contrastcontrols to maximum. Set the colour control to mini-mum.
(2) Select [AGC] in the service mode.(3) Change value until the snow noise just disappears.(4) Exit from the service mode.
(1) Input the SG signal to collector of Q101.SG signal frequency : 38.9 MHzSG signal level :70 dB
(2) connect a short clip between the baseofQ101 and -ground.
(3) Connect oscilloscope to pin 2 of IC201.(4) Select [VCO] in the service mode.(5) Change value until the voltage to be 4.5 * 1.OV.
(6) Exit from the service mode.
(1) Tune the receiver to the clearest station with SystemB/G(5.5MHz) in your area.
(2) Connect DC voltmeter to pin 46 of IC201 and ground.(2) Select [SIF] in the service mode.(3) Change value until the voltage to be about 3.0 V.(4) Exit from the service mode.
-
-14-
(1) Receive the monochrome circular pattern.(2) Set the brightness and colour to normal, contrast to
maximum.
(3) Enter to the service mode.(4) Set each value of [RBI], [GBI], [BBI] mode to O. Set each
value of [RD], [BD] mode to 64.(5) Select next of [DRVl mode to be one horizontal scan-
ning line and turn the screen volume on the FBT toobtain just visible one coloured line.
(6) Press the [1], [2], [5], [6], [9] or [0] buttonto adjust thebrightness of each colour until a dim white line pro-duced. Please see the control button allocations in thismode.
(7) Select [DRV] mode to enter the white balance adjustingmode.
(8) Press the [3], [4], [-/--] or [RECALL] button alternate-ly to produce normal black and white picture. Red Bias &
(9) Exit from the service mode.= (10) Check for proper grey scale tracking at all brightness ~r~~~~~~~z
levels.NOTE: If the grey scale adjustment is made after picture Green Bias --
tube replacement, check the high voltage. Blue Bias ~
Blue Bias --
~“E& &
0000;URROUND BASS VA*
000
OAO
G(E)D
‘t!5w&5TWrex’r 633m A ,Press ~] button to
vice mode
Red Drive +
Red Drive -
Blue Drive +
Blue Drive -
I
ADJUSTMENT-2Following adjustments are not required to readjust when replacing the memory IC.
L (1) Connect DC meter to TP-B and the ground. (1) Receive the monochrome circular pattern.
(2) Set the brightness and contrast to normal. (2) Set the brightness and contrast to normal.Tune the receiver to an active channel and synchro- (3) Adjust VR462 for optimum horizontal width.nized picture.
(3) The B-voltage must be 140 f 1 volt DC.
(1) Receive the monochrome circular pattern.(2) Set the brightness and contrast to maximum.(3) Connect a high voltage probe to anode lead of the pic-
ture tube.(4) The high voltage must be 29KV f 1KV and less than
32KV at O beam current.
NOTE:If the picture tube is replaced, check the high voltage.The horiz. width adjustment affects the high voltage.Therefore, re-check the high voltage.
L
-15-
Stereo Adjustments
A2/NICAM STEREO BOARD (Adjustment Location)
TPJ3405PILOT ALIGNMENT
STEREOIDUAL ■
SOUND PROCESSOR
nc3421
, J o oaii5”c2am..,-.
(F2W)
Setting Adjustment Waveform
DC 12V K34Z-pin 6 1. Adjust AGC voltage to beAGC voltage (DC5V-6V) IC3801 -pin 13 “A=O.05 - o.07vp-p.Output probe K34Z-pin8
P (38.9 MHz)2. By using T3802, adjust “P
(side a) to be on the top ofInput probe lC3801-pin 17 waveform.Sweep An 12dBMarker Frequency 38.9 MHz mov
Tools
Input probe Output probe
(1) Receive a stereo broadcast.(2) Connect oscilloscope to TPJ3804.(3) By using T3801 DC voltage to be 4.OV.
—
-WwT--p.ovp.p-16-
Setting
Oscilloscope
Input sound signal sourceTV systemDeviationMode
TPJ3405(lC3401-Pin5)
System B/G27kHzStereo
Adjustment
By using T3401, adjustamplitude to be maximum.
Separation-1
Setting
Oscilloscope
Input sound signal sourceTV systemDeviationModeModulation
Audio MonitorOut-Right Jack(K12RC3) on theBack unit.
System B/G27kHzStereoRight 1kHzLeft None
Setting
Input sound signal sourceTV systemDeviationModeModulation
Audio MonitorOut-Left Jack(Kl 2RC3) on theBack unit.
System B/G27kHzStereoRight 400HzLeft None
Adjustment
11) Press and hold the FUNCTIONkey on the TV set, and pressthe “4” key on the RemoteControl Transmitter to enter toK1 service mode.
ADJUST DATA
K1 -002
K1 Service Mode
(2)Adjust “A to be 1.4Vp-ptO.25Vusing the LEVEL UP or DOWNkey on the Remote ControlTransmitter.
Adjustment
(1) Press and hold the FUNCTIONkey on the TV set, and pressthe”4 key on the RemoteControl Transmitter to enter toKI service mode.
(2) Select K2 mode, by pressingthe FUNCTION key. (RC or TV)
ADJUST DATA
K2 -011
K2 Service Mode
(3) Adjust “B to be minimumusing LEVEL UP or DOWNkey on the Remoto ControlTransmitter.
To exit from the service mode, press the RECALL button.
-17-
Waveform
30JC1A
Waveform
Waveform
Special Functions
The following special functions can be set up on this TV set.(1)VOLUME LOCK SETTING(2) TUNING LOCK SEITING(3) AV START SETTING(4) BLUE BACK SETTING(5) MUSIC MODE SETTING
1Volume Lock setting I
With this function, a maximum volume limit can be set at any level.
1
Press the LEVEL button to set the desired maximum volume
LEVEL
kCHSCAN
(-) o-A
OOEoKrF A+
SWAP
o t’LEvEL(L~ To enter Special Function setting mode, press and hold the FUNCTION button on the TV set, then press the< remote control RECALIJCOLOUR SYSTEM button .
&
TVIAV PT F
@@
t
FUNCTION
“RECALIJCOLOUR SYSTEM
VOLUME LOCK OFF
~ Set VOLUME LOCK to the” ON” position by pressing the LEVEL (+ or - ) button. To cancel, set to the” OFF” s
- position.
q<
oF A+
ODE SWAP
o
‘LEVEL ( - )
4 Press the
LEVEL ( + )
VOLUME LOCK ON
T
RECALIJCOLOUR SYSTEM button to return to the normal TV mode.
-18-
Once TUNING LOCK is switched on, further channel tuning (Pre-set) is not possible.
1
2
3
L.
4
To enter Special Function setting mode, press and hold the FUNCTION button on the TV set, then press the remotecontrol RECALIJCOLOUR SYSTEM button .
TVIAV PT F
FUNCTION
@
078m
I. . .
YSTEM
VOLUME LOCK OFF
RECALIJCOLOUR SYSTEM
Select” TUNING LOCK” by pressing the FUNCTION button on the remote control or the TV set.
. -FUNCTION
L
TUNING LOCK OFF
Set TUNING LOCK to the” ON” position by pressing the LEVEL (+ or - ) button. To cancel, set to the” OFF”position.
LEVEL ( - ) .
kCH SCAN
o
-A
ODE
/
TUNING LOCK ON
Press the RECALL/COLOUR SYSTEM button to return to the normal TV mode.
.19-
I ISet AV-START to ON and every time the TV set is switched on, AV1will be the initial programme position.
Al/l
1
2
To enter Special Function setting mode, press and hold theremote control RECALIJCOLOUR SYSTEM button .
Select” AV START” by pressing the FUNCTION button on
I pWFUNCTION
FUNCTION button on the TV set, then press the
the remote control or the TV set.
AV START OFF
Set AV START to the” ON” position by pressing the LEVEL (+ or - ) button. To cancel, set to the” OFF” posi-tion.
3LEVEL,-,P6HLEVEL(+,
4 Press the RECALIJCOLOUR SYSTEM button
AV START ON /’
to return to the normal TV mode.
[ Blue Back setting 1
When BLUE BACK is on, a blue background will appear, if aprogramme position that is not receiving a signal is selected.
I TTurns blue when nosignal is received.
67
1
To enter Special Function setting mode, press and hold the FUNCTION button on the TV set, then press theremote control RECALL/COLOUR SYSTEM button .
Select” BLUE BACK “ by pressing the FUNCTION button on the remote control or the TV set.
21
PmFuNCTlON m
Set BLUE BACK to the” ON” position by pressing the LEVEL (+ or - ) button. To cancel, set to the” OFF” posi-
3~~EL(-)& &LEVEL(+) PI
4 Press the RECALUCOLOUR SYSTEM button to return to the normal TV mode.
-
d
-20-
I Music Mode setting I MUSIC
~~urns black,
When Music Mode is ON, Programme position from “91” to “99” and “O”are set Music Mode. Only sound is provided and any picture is not onthe screen under Music Mode.
L
d To enter S~ecial Function setting mode, press and hold the FUNCTION button on the TV set, then press the~ remote control RECALIJCOLOUR SYSTEM button .
TWAV PT FI
*
@@
}
FUNCTION
o5
09
A
o6
00#’i—
VOLUME LOCK OFF
‘RECALIJCOLOUR SYSTEM
2 Select” MUSIC MODE” by pressing the FUNCTION button on the remote control or the TV set.
I p*FUNCTION MUSIC MODE OFF
~ Set MUSIC MODE to the” ON” position by pressing the LEVEL (+ or - ) button. To cancel, set to the” OFF”0 position.
LEVEL ( - )
@
-A
ODE
4 Press the RECALUCOLOUR
o<
F 4+
SWAP
o rLEVEL ( + )
MUSIC MODE ON/’
SYSTEM button to return to the normal TV mode.
-21-
Purity and Convergence Adjustment
CAUTION: The Convergence and Purity adjustments have been made at the factory. Readjustment -should be made only after picture tube or deflection yoke replacement, following the steps below:
PURITY ADJUSTMENT1. Demagnetize the picture tube and receiver using an
external degaussing coil. When replacing picture tube ordeflection yoke, mount deflection yoke and purity-con-vergence magnets assembly properly, see figures 1 and4.
2. Turn Red and Blue guns off and provide only Greenraster. Rotate Screen control to fully counterclockwise.Rotate Red and Blue Bias controls fully counterclock-wise. Slowly rotate Green Bias control clockwise to pro-duce Green raster.
3. Loosen the screw holding the Deflection Yoke andremove the 3 Rubber Wedges, and slide the DeflectionYoke fully forward.
4. Rotate and spread the Tabs of the two Purity Magnetsto centre the vertical green belt in the picture screen.The Purity Magnets are also adjusted to obtain verticalcentring of the raster.
5. Slowly slide the Deflection Yoke backward until a uni-form green screen is obtained.
6. Check the purity of the red and blue screens for unifor-mity, turn off other colours to check this (use bias con-trols). Readjust the yoke position if necessary until allscreens are pure.
7. Adjust each Bias control and screen control to obtainwhite raster. Refer to Gray Scale Adjustment. If part ofthe picture screen is coloured, adjust the DeflectionYoke position forward or backward slightly.
8. Tighten the mounting screw of the Deflection Yoke.Adjust Convergence next.
CENTRE CONVERGENCE ADJUSTMENT1.
2.
3.
4.
Use a dot crosshatch pattern signal.Turn Red and Blue guns on and turn off Green gun.Adjust the angle between the Tabs of the Four PoleMagnet 1 and 2, and superimpose the Red and Bluevertical lines in the centre area of the picture screen.Refer to figure 2.Keeping the mutual angle of the Tabs of the Four PoleMagnet turn them together to superimpose the Blue andRed horizontal lines in the centre area of the picturescreen. Refer to figure 2.Turn Green aun on and adjust Six Pole Magnet 3 and 4that the Gre;n line superimposed on the Red/Blue lines.This is the same procedure used in steps 2 and 3. -Refer to figure 3.
OUTER AREA CONVERGENCE ADJUSTMENTSlightly loosen the screw holding the Deflection Yoke.Adjust the Deflection Yoke to converge the detail in theouter area (left side and right side) of the picture screen byorbital movement of the front of the Yoke, then secure theDeflection Yoke in appropriate position by putting thewedges as illustrated. Tighten screw holding the DeflectionYoke.
DEFLECTION YOKE
FOUR- POLEMAGNET TABS
SIX- POLE
rz .MAGNET TABS
Figure- 1. PURITY AND CONVERGENCE MAGNETS
w
Figure- 4. ADJUSTMENT DEFLECTION YOKE
Adjust tabs angle to superimposeblue and red vertical line.
17,v Adjust tabs together to*
RED ,superimpose red and1
+
1
i
blue horizontal line1I------- - .F ---- ---
Adjust tabs angle to superimposered/blue and green vertical line.
17,
1/Adjust tabs together to
;+GREEN ; superimpose red/blue
+
11
iand green horizontal
1------- - .P---.- -- line.
=T’Figure- 2 BLUE AND RED LINE MOVEMENT I Figure- 3 BLUE/RED AND GREEN MOVEMENT
.-
-
-22-
----
L
Cabinet Parts ListF2DT
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
8
,,.,,.,
6 5
Key No. Part No. Description
1 610 275 2335 BUTTON POWER
2 610 229 8406 SPRING
3 610 273 4812 DEC IND
4 610 273 4799 DOOR
5 610 273 9275 DEC CONTROL SHEET
6 610 104 2505 LATCH PUSH,7.9X6.9BK
OR 645 019 2449 LATCH PUSH,7.9X6.9BK
7 645 030 7355 BADGE,SANYO
8 610 277 0636 COMPL,CABINET FRONT
8-a 610 273 2399 CABINET FRONT
8-b 645 019 2210 HANDLE
9 610 273 4447 GRILLE SPEAKER LEFT
10 610 273 4430 GRILLE SPEAKER RIGHT
11 610 274 0325 DEC SPEAKER SHEET
12 610 273 4805 DEC SPEAKER
’11
’12
,5/
i4
‘------1 6
Key No. Part No. Description
13 610 274 6884 CABINET BACK
14 610 278 7580 LABEL RATING
15 645 030 7485 ASSY,REMOCON JXMEA
16 610 261 8020 RC-BATTERY LID
610 278 7030 INSTRUCTIONS NANUAL
-23-
Chassis Electrical Parts List F2DT
Product safety should be considered when a component replacement is made in any area of a receiver..
Components indicated by a A mark in this parts list and the circuit diagram show components whose value havespecial significance to product safety. It is particularly recommended that only parts specified on the following partslist be used for components replacement pointed out by the mark.
Note: Parts order must contain Service Ref. No., Part No., and descriptions. The main PCB unit will be supplied without tuner andflyback transformer. They should be ordered separately.
Ref. No. Part No. Description Ref. No. Part No. Description
NOTES: OUT OF CIRCUIT BOARD
Read description in the Capacitor and Resistor as follows: PICTURETUBE
A: Not specified B: ifl.1 pF C : iO.25PF A L902 645 009 9267 YOKE, DEFLECTIOND :&3.5pF F:+IPF G : tipFR : N.25-OPF S : fl-O.25PF E : +O-IPFMore than 10PF
MISCELLANEOUS
A : Not specified B : H.1 % C : i?3.25% SP901 645 002 4313 SPEAKER,8
D : N.5% F:+l% G : e% SP902 645 002 4313 SPEAKER,8
H : *3% J : *5% K : +10% Aw901 645 009 9991 CORD, POWER-2 .4MK-A5003
L :*I5% M :i20% N :+30% W903AP :+100-0% Q :+30-10% T :+50-1O%
610 275 0072 ASSY, WIRE GND CONNECTOR F
u :+75-lo% v :+20-10% w :+100-10%X : +40-20% Y : +1 50-1 O% Z : +80-20% 6102739077 ASSY PWB TEXT F2EA