T SERIES Full Metal Luminance
TSERIES
Full Metal Luminance
contacts
contact arrangement 1C (1 Form C), 2C (2 Form C)
contact material Ag alloy (24K gold tint)
regular insulating voltage 250VAC
maximum carry current 3A max.
maximum switching voltage 250VAC, 110VDC
rated load1A 24VDC / 120VAC
0.5A 250VAC
min applicable load 10mA 5VDC
LED
color red, green, yellow, blue, white, orange
appearance round
norminal voltage 24VDC, 12VDC, 6VDC, 220VAC, 110VAC
norminal current 15mA approx.
expected Life 1) 50,000hours
1) �Luminance is reduced to 50% of inital intensity after being lit for 50,000 hours continuously.
SPECIFICATION
Generalspecification
contact resistance max. 50mΩ
insulation resistance min. 100MΩ (500VDC)
dieletric strength 2,000VAC for1min.
vibration resistance 5~55Hz dual amplitude : 0.75mm
shock resistance endurance: 500m/s2, operation error : 200m/s2
expected life
mechanicalmomentary : 1,000,000 min, selector : 250,000 min,
alternate : 100,000 min.
electricalmomentary : min. 100,000 (frequency of on/off 1,200 times / hour)
alternate min. 50,000
ambient temperature -25℃ ~ +55℃ (with no icing)
ambient humidity 45% ~ 85%RH
degree of protection IP65 waterproof
terminal soldering temperature 20W 5sec / 260℃ 3sec
1 description 1 : pilot Lamp4 : 2step selector7 : 3 step Key
2 : momentary5 : 3step selector8 : emergency reset (nominal)
3 : alternate6 : 2 step key
2 illumination & bezel shape 1 : round7 : LED round
2 : square8 : LED square
3 : rectangular9 : LED rectangular
3 contact arrangement 0 : no contact 1 : 1a + 1b 2 : 2a + 2b
4 lens color R : redB : blue
G : greenO : orange
Y : yellowW : white
5 norminal votage 6VDC110VAC
12VDC220VAC
24VDC
T19 SeriesT19 - ❶ ❷ ❸ ❹ ❺
PART NUMBER DESCRIPTION
pilot lamp
bezel shape
momentary & alternate push button switch
bezel shape
selector switch
bezel shape
key switch
bezel shape
emergency reset switch
bezel shape
socket
K16-S113 (soldering socke) K16-S114 (P.C.B. socket)
24.0
18.0
DIMENSION
4.5
4.0
18.0
WIRING DIAGRAM
Bottom Viewilluminated
LED�LampTerminae
illuminated2a + 2b
illuminated1a + 1b
Panel cut-outpilot push button key selector switch emergency
19.0 + 0.2 19.0 + 0.2
Min
26.0
Min
35.0
Min 26.0 Min 35.0
SPECIFICATION
1 description 1 : pilot Lamp 2 : momentary 3 : alternate
2 illumination & bezel shape 1 : round 7 : LED round
3 contact arrangement 0 : no contact 1 : 1a + 1b (T22) 2 : 2a + 2b (T25)
4 lens color R : redB : blue
G : greenO : orange
Y : yellowW : white
5 norminal votage 6VDC110VAC
12VDC220VAC
24VDC
T22/25 SeriesT22/25 - ❶ ❷ ❸ ❹ ❺
generalpecification
regular insulating voltage 250VAC/DC
insulation resistance min 100MΩ (500VDC)
dieletric strength
between the charging section and the earth
min. 2,000VAC (1min.)
between the charging sections min. 1,500VAC (1min.)
expected lifemechanical
momentary : 1,000,000 min.
alternate : 250,000 min.
electrical min. 100,000
frequency of on/off 1200 times / hour
vibration dual wave length 0.1mm (10-55Hz)
impactoperation error : 100㎨durability : 500㎨
ambient temperature -20 ~ +70℃ (anti-freezing)
relative humidity 45 ~ 85%RH (at -5 ~ +40℃)
controlling protection structure IP65 (water/oil proof)
contacts
contact arrangementT22 : 1C(1a+1b)T25 : 1C(1a+1b), 2C(2a+2b)
contact material Ag alloy (24K gold tint)
regular insulating voltage 250VAC
regular applicable current 5A max.
max. on/off voltage 250VAC / 110VDC
regular current used
resistance load (AC12/DC12) induction load (AC13/DC13)
3A 24VDC 0.7A 24VDC
0.2A 125VDC 0.15A 125VDC
3A 110VAC 1A 110VAC
1.5A 250VAC 0.7A 250VAC
min. applicable current 10mA 5VDC
lit part
color red, green, yellow, blue, white
appearance round
regular current used 24VDC, 12VDC, 6VDC, 220VAC(to be released)
norminal current 15mA Approx.
expected life 50,000hrs
lamp type LED
PART NUMBER DESCRIPTION
pilot lamppanel cut-out
bezel shape
pilot lamppanel cut-out
bezel shape
DIMENSION
T22
T25
1. Connection of wires
1) Soldering
•The power consumption of the soldering iron must be 30 W or less.
•Use a 30 W soldering iron for 5 s or less, and a 20 W soldering iron for 10 s or less.
2) Tab terminal
•Use the #110 tab terminal.
3) Wires for connection
•Single wire: Max.Ø0.8mm
•Stranded wire: Max. 0.75mm2
2. Replacement/installation of the front button and LED
1) Button : Use a driver in the groove on the side of the button to remove it (To insert the button, push it until it clicks.).
2) LED : Pull the LED using a tool such as pliers. Assemble it in the reverse sequence of the disassembly.
3. Mounting the product on the panel
1) Press both the projections of the contact unit module with two fingers to remove the module from the operating unit.
2) The operating unit and contact unit module have their directivity. Use caution for insertion.
3) Separate the fixing ring and anti-rotation fixture from the operating unit.
4) Insert the operating unit in the panel, and assemble it in the reverse order of the disassembly.
5) The fixing ring can be firmly tightened using the K16-W1.
4. Contact block replacement/installation
1) Widen four projections on both sides of the contact unit module to separate the contact block.
2) Push the contact block into the empty space of the contact unit module to assemble it. The block is mounted with a click sound.
(Be sure to check the left and right sides are firmly locked.)
3) A maximum of three (3a+3b) contact blocks can be mounted.
5. When using a Ø16 small control switch as the power switch for the control unit, please follow the following instruction for longer product life span and reliability.
S/W Contact
S/W Contact
6. When rectifying the AC current for the DC power for lighting, the DC power must be a constant voltage source with a ripple range of 10 % or less. Otherwise, the LED life is significantly reduced7. Do not apply excessive impact or force to prevent damage to the product. When using the K16-W1 tool, do not tighten the fixing ring with an excessive force, because it may damage the product (When fixing the product on the panel, the tightening torque must be 0.6~1 N·m or less).8. When soldering the terminal for wiring, comply with the specified temperature and time. Failure to meet the specifications may lead to the damage and thermal defromation to the product.
pre-caution
1588-4036+82-32-575-4036
www.kacon.co.kr
Copyright ⓒ 2012 KOREA AUTO CONTROLS CO., LTD. All Rights Reserved.
ISBN-KAP-1207 1.0K