• 41.4' ft to 162' ft (12.6 - 49.3 m) five-section formed full power latching boom with no charted capacity deductions for telescoping loads • Five boom extend modes provided superior capacities: EM1-EM5 • Optional 31 ft to 55 ft (9.4 - 16.7 m) two-piece, bi-fold, on-board lattice attachment with 2°, 15° 30°, and 45° manual offsets • Optional 10 - 31 - 55 ft (3.0 - 9.4 - 16.7 m) three-piece, bi-fold, on-board lattice attach- ment with 2°, 15° 30°, and 45° manual offsets, and 2° through 45° hydraulic offsets • Optional three 18 ft (5.5 m) fly extensions plus 55 ft (16.7 m) provide a total attachment length of 109 ft (33.2 m) • 278 ft (84.7 m) maximun tip height • No deducts for stowed attachments • 21,022 lbs (9 535.4 kg) maximum winch line pull • 431 fpm (131.4 m/min) maximum winch line speed • Electronic joystick controllers • 6x2 and 6x6 drive with 23.5R25 tires • Four steering modes: independent front, combination, crab, and independent rear • Hydrostatic drive • Fully independent double “A” arm hydraulic suspension Rough Terrain Crane 130-ton (120.0 mt) SERIES II
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
• 41.4' ft to 162' ft (12.6 - 49.3 m) five-section formed full power latching boom with no chartedcapacity deductions for telescoping loads
• Five boom extend modes provided superiorcapacities: EM1-EM5
• Optional 31 ft to 55 ft (9.4 - 16.7 m) two-piece, bi-fold, on-board lattice attachmentwith 2°, 15° 30°, and 45° manual offsets
• Optional 10 - 31 - 55 ft (3.0 - 9.4 - 16.7 m)three-piece, bi-fold, on-board lattice attach-ment with 2°, 15° 30°, and 45° manual offsets, and 2° through 45° hydraulicoffsets
• Optional three 18 ft (5.5 m) fly extensionsplus 55 ft (16.7 m) provide a totalattachment length of 109 ft (33.2 m)
• 278 ft (84.7 m) maximun tip height
• No deducts for stowed attachments
• 21,022 lbs (9 535.4 kg) maximumwinch line pull
• 431 fpm (131.4 m/min) maximum winch line speed
• Electronic joystick controllers
• 6x2 and 6x6 drive with 23.5R25 tires
• Four steering modes: independent front, combination, crab, and independent rear
• Hydrostatic drive
• Fully independent double “A” arm hydraulic suspension
Rough Terrain Crane130-ton (120.0 mt)
SERIES II
The industry’s most innovativesolution to big rough terraincrane maneuverability andtransportability!
• Revolutionary hydrostatic driveon a six-wheeled carrier forthe ultimate in job site mobility
• Unprecedented transportability
• Maneuverability redefined
• Over 45 tons (40.8 mt) of on-tire capacity
CALC–Outrigger beams extend to three different positions (retracted, intermediate,and fully extended) providing lifting capacitiesin confined areas
Independent front Coordinated six wheel driveIndependent rear
Flat deck design and non-slipsurface strips on deck
Complete lighting package
Fast "hook-and-pin" front &rear outrigger beams
Repositionable ladders onfront and back
Stowable pontoons
The reach of the optional 55' (16.8 m) two or three-piece offsettable, bi-folding fly can be extended byadding three optional 18' (5.5 m) inserts
Mechanical boom angleindicator-standard
Optional integrated airconditioning
Folding viewing mirror for travel
Rough Terrain Crane130-ton (120.0 mt)
SERIES II
Six wheel "crab"
Revolutionary hydrostatic drive ona 6-wheel carrierNot only is this crane easy to get from jobsite to jobsite, it also has extraordinary creep control and jobsite maneuverability, thanks to its hydrostatic powered motors in eachwheel. The smaller tires give it an overall height that is ideal for hauling, along with its’ individual six-wheel hydrostatic drive, there is no crane in the world, any size, that cancome close to the job site maneuverability and performance of the RTC-80130 Series II.
On the job, the RTC-80130 Series II has outstanding on-tire capacity coupled with its longreach, maneuverability, incredible gradeability and low height make it truly an ideal solutionfor industrial sites.
Partial counterweight andno counterweight charts
Catwalks on bothsides of upper
23.5R25 radial tires
Because of the innovative 6x6x6 hydrostatic drive/steer on each wheel, the turning
radius of the 28' 10" (9.1 m) long carrier is a remarkable 21' 10" (6.6 m).
• Main and availableauxiliary winch areequally matched insize and perform-ance
• Provisions for thefuture installation ofthe auxiliary winchare standard
Swing-out doors provide exceptional accessto engine components.
Access is superb with strategically-locatedladders, steps, catwalks and CabWalk.
Operator cab features• Extra large windows throughout for
excellent visibility• Excellent ventilation via a large sliding
door, side and rear windows, and hingedroof window
• 6-way adjustable power tilting seat• Single or dual axis, electronic operated
controller mounted on armrest for outstanding operator comfort
• All gauges, switches, indicators, and controls are located in the operator’s forward line of sight
• All gauges and switches are backlit forexcellent visibility in low light conditions
• Integral rated capacity limiter aids operator in safe and efficient operation
• In cab comfort is maintained by the standard heater
• Available - Internal and external ratedcapacity limiter light bars
• Available - Integrated air conditioning utilizes the same ventillation outlets as the standard heating system
• Available - cab mounted warning lights
cuthere
Õ
Õ
Õ
Õ
Í
Full power boom withattachment flexibility
Innovative 10 ft (3.0m) fly is integral to oneof the on-board fly options. Over 25 tons
(22.6 mt) capacity and one-loadtwo-line lift procedures.
cuth
ere
• Quick reeve boom head eliminates the need to remove the becket when it becomes necessary to change the reeving
• Five extend modes for superior capacitiesthroughout the extension range
• Available two or three-piece bi-folding lattice fly which allow the tip section to be stored, thusenhancing the lifting performance when usingthe base section
• Boom requires no greasing because of ingeniousTeflon wear pucks impregnated in the full contactwear pads
• Two available offset fly options: manual offset with 2°, 15°, 30°, and 45°, and a hydraulic offset with2° - 45° with no capacity deduction for luffing loads
• No deducts for stowed attachments
260'(79.2 m)
243' (74.1 m)
278'(84.7 m)
189' (57.6 m)
18' + 18' + 18' + 55' (5.4 + 5.4 + 16.7 m)
18' + 18' + 55' (5.4 + 5.4 + 16.7 m)
18' + 55' (5.4 + 16.7 m)
18' (5.4 m)
Optional Lattice Fly Extension
225'(68.7 m)
202' (61.5 m)
181' (55.1 m)
Optional Lattice Fly Onboard
10' (3 m)
31' (9.4 m)
55' (16.7 m)
Breakthroughtransportability• Unlike any other rough terrain crane in this class,
in less than an hour and without a helper crane, theRTC-80130 Series II is ready for transport.
• Unlike other big RT's, the tires do not need to beremoved for transport.
• Only the counterweights and outrigger boxes needto be removed to get the crane's vehicle width under10' (3.05 m).
• Because it is under 10' (3.05 m) wide and features alow overall height, the RTC-80130 Series II transportseasier than the competition.
Link-Belt ConstructionEquipment Company isa leader in the design,manufacture and sales oftelescopic and lattice boomcranes, with headquarters inLexington, Kentucky.
In the recent decade, a dynamic and highlyfocused Link-Belt has emerged as a marketleader in crane design and product qualitystandards by focusing on continuousimprovement and employee empowerment.
Link-Belt operates on the principles ofcontinuous quality improvement, ISO 9001,and established values that support thevision of quality. These principles result inreduction in waste, better use of companyresources and improved employee andcustomer satisfaction.
With major capital improvements overthe last ten years, along with continuous
Lexington, Kentucky
www.linkbelt.com
® Link-Belt is a registered trademark. Copyright 2009.All rights reserved. We are constantly improving ourproducts and therefore reserve the right to changedesigns and specifications.
Litho in U.S.A. 10/09 #4367
15567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
Technical DataSpecifications & Capacities
130 US ton120 metric ton
CAUTION: This material is supplied forreference use only. Operator must refer toin---cab Crane RatingManual andOperator’sManual to determine allowable crane liftingcapacities and assembly and operatingprocedures.
Boom, Attachments, and Upper StructureJ BoomDesign --- Five section, formed construction of extra hightensile steel consisting of one base section and four tele-scoping sections. The two plate design of each section hasmultiple longitudinal bends for superior strength. Each tele-scoping section extends independently by means of onedouble---acting, single stage hydraulic cylinder with integ-rated holding valves.BoomS 41.4---162 ft (12.6 ---49.3m) five section boomS Five boom extend modes (EM1 through EM5), controlledfrom the operator’s cab, provide superior capacities byvarying the extension of the telescoping sections:S EM1 extends to 162.0 ft (49.3m)S EM2 extends to 150.0 ft (45.7m)S EM3 extends to 124.7 ft (38.0m)S EM4 extends to 112.0 ft (34.1m)S EM5 extends to 86.2 ft (26.3m)
S Mechanical boom angle indicatorS Maximum tip height for each extend mode is:S EM1 is 171 ft (52.1m)S EM2 is 159 ft (48.5m)S EM3 is 134 ft (40.8m)S EM4 is 122 ft (37.2m)S EM5 is 96 ft (29.3m)Boom Wear PadsS Wear pads with Teflon inserts that self ---lubricate theboom sections
S Bottom wear pads are universal for all telescoping boomsections
S Bottom wear pads are universal for the boom basesection
S Top wear pads are universal for all boom sectionsBoom HeadS Six 16.38 in (41.6cm) root diameter nylon sheaves tohandle up to twelve parts of line
S Easily removable wire rope guardsS Rope dead end lugs on each side of the boom headS Boom head is designed for quick---reeve of the hookblockBoom ElevationS One double acting hydraulic cylinder with integral hold-ing valve
S Boom elevation: ---2.5˚ to 80˚Auxiliary Lifting Sheave --- OptionalS Single 16.38 in (41.6cm) root diameter nylon sheaveS Easily removable wire rope guardsS Does not affect erection of the fly or use of the main headsheavesHook Blocks and Balls --- OptionalS 140 ton (127.0mt) 7 sheave, quick---reeve hook blockwith safety latch
S 100 ton (90.7mt) 6 sheave, quick---reeve hook block withsafety latch
S 80 ton (72.5mt) 5 sheave, quick---reeve hook block withsafety latch
S 35 ton (31.7mt) 1 sheave, quick---reeve hook block withsafety latch
S 12 ton (10.8mt) hook ball (swivel) with safety latchFly --- OptionalS 31 ft---55 ft (9.4---16.7m) two piece bi---fold lattice fly, stow-able, offsettable to 2˚, 15˚, 30˚, and 45˚. Maximum tipheight is 225 ft (68.6m).
S 10 ft, 31 ft --- 55 ft (3.0, 9.4---16.7m) three piece bi---fold lat-tice fly, stowable, offsettable to 2˚, 15˚, 30˚, and 45˚. Max-imum tip height is 225 ft (68.6m).
S 10 ft, 31 ft --- 55 ft (3.0, 9.4---16.7m) three piece bi---fold lat-tice fly, stowable, hydraulically offsettable from 2˚ through45˚. Maximum tip height is 225 ft (68.6m).Fly Extensions --- OptionalS One 18 ft (5.5m) lattice extension, equipped with two16.38 in (41.6cm) root diameter nylon sheaves, to bemounted between the boom head and fly options. Max-imum tip height is 243 ft (74.1m).
S Two 18 ft (5.5m) lattice extensions, one equipped withtwo 16.38 in (41.6cm) root diameter nylon sheaves, to bemounted between the boom head and fly options. Max-imum tip height is 260 ft (79.2m). Minimum of 26,000 lb(7 924.8kg) of counterweight required.
S Three 18 ft (5.5m) lattice extensions, one equipped withtwo 16.38 in (41.6cm) root diameter nylon sheaves, to bemounted between the boom head and fly options. Max-imum tip height is 278 ft (84.7m). Minimum of 26,000 lb(7 924.8kg) of counterweight required.
J Operator’s Cab and ControlsEnvironmental Cab --- Fully enclosed, one person cab ofgalvaneal steel structure with acoustical insulation.Equipped with:S Tinted and tempered glass windowsS Extra---large fixed front window with windshield wiper andwasher
S Swing up roof window with windshield wiperS Sliding left side door with large fixed windowS Sliding rear and right side windows for ventilationS Six way adjustable, power tilting cushioned seat with seatbelt
S Engine dependent warm---water heater with air ducts forfront windshield defroster and cab floor
S Defroster fan for the front windowS Bubble levelS Circulating fanS Adjustable sun visorS Dome lightS Cup holderS Fire extinguisherS Left side viewing mirrorS Two position travel swing lock
2 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
Air Conditioning --- Optional --- Integral with cab heatingsystem utilizing the same ventilation outletsSteering Column --- Pedestal type with tilt and telescopefunctions for operator comfort. Column includes the follow-ing controls and indicators:Left and right levers include:
S Horn buttonS Turn signal switchS Driving light switchS Forward/Neutral/Reverse direction switchPanel mounted switches for:
S Travel park brakeS Steer mode selectorS 2/6 wheel drive/range selectorS Hazard flasherPanel mounted indicator/warning lights for:
S Travel circuit temperature S Charge filter restrictionS Engine oil pressure S Pump CPU errorS Travel park brake S Engine overspeedS Service brake S Rear wheel offsetS Turn signals S Emergency steer ---S Case filter restriction optionalArmrest Controls --- Power tilt with seat for operator com-fort. Two dual axis electronic joystick controllers or optionalsingle axis electronic controllers for:S SwingS Boom hoistS Main front winchS Auxiliary rear winch --- optionalS Drum rotation indicationS Drum rotation indicator activation switchS Winch high/low speed and disable switch(es)S Fine inching mode switchS Power tilting seat switchS Warning horn buttonS Swing park brakeS Third wrap selector switch --- optionalOutrigger Controls --- Hand held control box with umbilicalcord gives the operator the freedom to view operation whilesetting the outriggers.Foot ControlsS Boom telescopeS Swing brakeS Engine throttleS Service brakeRight Front Console --- Controls and indicators for:S Engine ignition S Console dimmer switchS Engine throttle lock S Bubble levelS Function disable S 12 volt power connectionS Front windshield wiper S Air conditioning --- optionaland washer S Boom floodlight --- optional
S Cab floodlights light S Rotating beacon/StrobeS Warning horn light --- optionalS Heating controls
Cab Instrumentation --- Ergonomically positioned, analoginstrumentation for crane operation including:S Engine coolant temperature with warning indicatorS Hydraulic oil temperature with warning indicatorS Fuel level with warning indicatorS TachometerS Travel circuit temperature with warning indicatorS Voltmeter with warning indicatorRated Capacity Limiter --- Microguard graphic audio---visual warning system integrated into the dash with anti ---two block and function limiter. Operating data availableincludes:S Crane configurationS Boom length and angleS Boom head heightS Allowed load and % of allowed loadS Boom angleS Radius of loadS Actual loadS Wind speedS Third wrap indicators --- optionalS Operator settable alarms (include):S Maximum and minimum boom anglesS Maximum tip heightS Maximum boom lengthS Swing left/right positionsS Operator defined area (imaginary plane)Internal RCL Light Bar --- Optional --- Visually informs theoperator when crane is approaching maximum load capa-city with a series of green, yellow, and red lights.External RCL Light Bar --- Optional --- Visually informs theground crew when crane is approaching maximum loadcapacity with a series of green, yellow, and red lights.
J SwingMotor/Planetary --- Bi ---directional hydraulic swing motormounted to a planetary reducer for 360˚ continuoussmooth swing at 1.5 rpm.Swing Park Brake --- 360˚, electric over hydraulic, (springapplied/hydraulic released) multi ---disc brake mounted onthe speed reducer. Operated by a switch from the operat-or’s cab.Swing Brake --- 360˚, foot operated, hydraulic applied discbrake mounted to the speed reducer.Swing Lock --- Two---position swing lock (boom over frontor rear) operated from the operator’s cab.
J ElectricalSwing Alarm --- Audio warning device signals when theupper is swinging.LightsS Two working lights on front of the cabS One rotating amber beacon on top of the cab --- optionalS One amber strobe beacon on top of the cab --- optionalS Boom floodlight --- optional
35567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
J Load Hoist SystemLoad Hoist Performance
Main (Front) and Auxiliary (Rear) Winches --- 7/8 in (22mm) RopeMaximum Line Pull Normal Line Speed High Line Speed Layer Total
2M Main (Front) and Optional Auxiliary(Rear) WinchesS Axial piston, full and half displacement (2---speed) motorsdriven through planetary reduction unit for positive con-trol under all load conditions.
S Grooved laggingS Power up/down mode of operationS Hoist drum cable follower --- optionalS Drum rotation indicatorS Drum diameter: 15 in (38.1cm)S Rope length:S Main (Front): 850 ft (259.0m)S Auxiliary (Rear): 600 ft (182.8m) or 850 ft (259.0m)
S Maximum rope storage: 951 ft (289.9m)S Terminator style socket and wedgeThird Wrap Indicator --- Optional --- Visually and audiblywarns the operator when the wire rope is on the first (bot-tom) layer and when the wire rope is down to the last threewraps.
J EngineSpecification Caterpillar C9
Numbers of Cylinders 6
Cycle 4
Bore and Stroke: inch (mm) 4.41 x 5.87 (112 x 149)
Piston Displacement: in3 (L) 537 (8.8)
Max. Brake Horsepower: hp (kW) 325 (242.3) @ 2,200 rpm
Peak Torque: ft lb (Nm) 1,095 (1 485) @ 1,400 rpm
Alternator: volts --- amps 12/145
Crankcase Capacity: qt (L) 34 (32)
S 120 V engine block heaterS Ether injection system --- optional
4 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
J Drive SystemHydrostatic type consisting of two variable speed pistonpumps supplying hydraulic power to six hydraulic cam lobewheel drive motors computer controlled for smooth andreliable operation.
J Fuel TankOne 95 gal (359.6L) capacity tank
J Hydraulic SystemAll functions are hydraulically powered allowing positiveprecise control with independent or simultaneous operationof all functions.Main PumpsS One, two section gear pump for the boom hoist, tele-scope, and charge circuits.
S Two, closed---loop piston pumps serve as travel pumps.these two pumps supply hydraulic power to the wheelmotors.
S Two, closed---loop piston pumps are mounted to the rearof the two travel pumps. The left pump drives the frontwinch and the right pump drives the optional rear winch.
S One, pressure compensated piston pump mounted tothe rear of the left winch pump supplies hydraulic powerto the outrigger, counterweight removal (optional), oscilla-tion, and travel brake circuits.
S One, single section gear pump mounted to the rear of theright side winch pump supplies hydraulic power to theswing and steering circuits.Hydraulic Reservoir --- 255 gal (965.2L) capacity equippedwith sight level gauge. Diffuser built in for deaeration.Magnetic drain plug and large internal magnet.FiltrationS One, 7---micron filter located inside hydraulic reservoir,accessible for easy replacement
S One, 7---micron charge filter located next to the reservoirwith an in---cab indicator light
S Two, 10---micron pressure filters located next to the reser-voir with change indicators
S Three, 100 mesh suction strainers located inside the hy-draulic reservoirValve Control “Fine Inching” Mode --- Special fine meter-ing valve settings, selectable from the operator’s cab, al-lows very slow movements to the main and auxiliarywinches, boom hoist, and swing for precision work.Counterbalance Valves --- All boom extend cylinders andboom hoist cylinder are equipped with counterbalancevalves to provide load lowering and prevents accidentalload drop when hydraulic power is suddenly reduced.Hydraulic Oil Cooler --- Integral to the engine radiator/charge air cooler. Removes heat from the hydraulic oil.Auxiliary Hydraulic Oil Cooler --- Mounted in front of hy-draulic reservoir provides additional hydraulic cooling dur-ing machine traveling.
J Pump DriveAll pumps are mounted on the pump drive gearbox andmechanically driven by the diesel engine.
J CounterweightStandard --- Total of 29,000 lb (13 154kg) consisting ofauxiliary winch or 2,000 lb (907kg) top counterweight,two 12,000 lb (5 443kg) and one 3,000 lb (1 360kg) re-movable counterweights pinned to the upper with capa-cities for:S 0 lb (0kg) counterweightS 14,000 lb (6 350kg) counterweightS 17,000 lb (7 711kg) counterweightS 26,000 lb (11 794kg) counterweightS 29,000 lb (13 154kg) counterweightOptional --- Total of 14,000 lb (6 350kg) in addition tostandard counterweight for a total of 43,000 lb (19 505kg)counterweight with additional capacities for:S 43,000 lb (19 505kg) counterweight** Overall width of the crane increases to 13 ft 4 in (4.0m) forthis counterweight configuration.Hydraulic Counterweight Removal --- Optional --- Activ-ated by a hand---held controller with enough cable to ac-cess the pins on each side of the counterweights.
55567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
29,000 lb (13 154kg) 43,000 lb (18 505kg)
14,000 lb(6 350kg)2---PieceWings
2,000 lb (907kg)Top or AuxiliaryWinch 3,000 lb
(1 360.8kg)Piece
12,000 lb(5 443kg)Piece
12,000 lb(5 443kg)Piece
2,000 lb (907kg)Top or AuxiliaryWinch
3,000 lb(1 360.8kg)Piece
12,000 lb(5 443kg)Piece
12,000 lb(5 443kg)Piece
CounterweightPackages
29,000 lb (13 154kg) --- Standard
43,000 (18 505kg) --- Optional
CounterweightModules
3,000 lb(1 361kg)Piece
12,000 lb(5 443kg)Piece
12,000 lb(5 443kg)Piece
2,000 lb(907kg)Top*
14,000 lb(6 350kg)2---Piece
CounterweightUsage
Configurations
0 lb(0kg)
14,000lb(6 350kg) X X17,000 lb(7 711kg) X X X26,000 lb(11 794kg) X X X29,000 lb(13 154kg) X X X X43,000 lb(19 505kg) X X X X X
* Auxiliary winch replaces this counterweight for a two---drum configuration
6 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
CarrierJ GeneralS 9 ft 10 in (3.00m) wideS 16 ft 1 in (4.90m) wheelbase (centerline of first axle tocenterline of third axle).Frame --- Box---type, torsion resistant, welded constructionmade of high tensile steel. Equipped with front and reartowing and tie---down lugs, tow connections, and accessladders.
J OutriggersBoxes --- Two removable, double box, front and rearpinned to carrier frame. Hydraulic hoses have quick---dis-connect fittings for ease for box removal. Hydraulic outrig-ger pin removal activated by a hand---held controller --- op-tional.Beams and Jacks --- Four single stage beams with Con-fined Area Lifting Capacities (CALC™) provide selectableoutrigger extensions of full, intermediate, and retracted.Hydraulically controlled from the operator’s cab with integ-ral check valves.Pontoons --- Four lightweight, quick release, 26 in (0.66m)diameter, steel pontoons with contact area of 531 in2(3 425cm2) can be stored for road travel in storage rackson the carrier.Main Jack Reaction --- 160,000 lb (72 574kg) force and301 psi (2 075.3kPa) ground bearing pressure.
J Steering and Wheel Drive MotorsSteering --- Four independent modes consisting of twowheel front, four wheel rear, six wheel, and crab. Eachmode is controlled from the steering wheel and is selectedby a switch in the operator’s cab.Drive --- Three modes: 6x2 high, 6x2 low, and 6x6 for offhighway travelFront Drive Motors --- Steered, driven for 6x2 and 6x6Rear Drive Motors --- Steered, non---driven for 6x2 andsteered, driven for 6x6
J SuspensionFront --- Double “A” arms connected to oscillation cylindersthat lockout when the upper structure rotates 3˚ past cent-erlineLeft Rear --- Center and rear wheels mounted on double“A” arms connected to oscillation cylinders that lockoutwhen the upper structure rotates 3˚ past centerline. Os-cillation occurs across left center and left rear wheels.Right Rear --- Center and rear wheels mounted on double“A” arms connected to oscillation cylinders that lockoutwhen the upper structure rotates 3˚ past centerline. Os-cillation occurs across right center and right rear wheels.Ride Height Adjustment --- Suspension can be lowered fortransport using a hand---held controller from the ground.
J Tires and WheelsFront and Rear --- Six (single) 23.5R25, earthmover typetires on steel disc wheelsS Spare tires and wheels --- optional
J BrakesService --- Full hydraulic, dual circuit, disc type brakes onall wheel endsParking/Emergency --- Spring loaded type, acting on frontwheel ends
J ElectricalThree batteries provide 12 volt operation and startingLightsS Front lighting includes two main headlights and two park-ing/directional indicators
S Side lighting includes two parking/directional indicatorsper side
S Rear lighting includes two parking/directional indicators,two parking/brake lights, and two reversing lights
S Other equipment includes hazard/warning system
J Carrier Speeds and GradeabilityVariableHydrostaticDrive
Speed Gradeability
Range mph km/h % Grade
6 WD Low 3.1 4.9 44
2 WD Low 9.3 14.9 12
2 WD High 17.0 27.3 5
Based on a gross vehicle weight of 150,000 lb (68 038kg).Crane operating angle must not exceed 30˚ (66% grade).
J Hydraulic SystemDrive System --- Hydrostatic type consisting of two variablespeed piston pumps supplying hydraulic power to six hy-draulic cam lobe wheel drive motors computer controlledfor smooth and reliable operation.Filtration --- One, 60---micron, full flow, line filter in thewheel motor case drain circuit. Filter includes an in---cabchange indicator. Accessible for easy filter replacement.
75567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
Axle Loads -- English
Base machine with full tank of fuel and 29,000 lbof counterweight
Gross VehicleWeight (1)
Upper Facing Front Upper Facing RearFront Axle Rear Axle Group Front Axles Rear Axle Group
Hoist drum follower --- main 99 ---49 148 ---49 148Auxiliary winch with 600 ft of wire rope 955 ---531 1,486 ---531 1,486Remove auxiliary winch with 600 ft of wire rope ---for two winch configuration only ---2,783 1,764 ---4,547 ---3,903 1,121
Hoist drum follower --- auxiliary 101 ---75 176 ---75 176Remove 850 ft of wire rope --- main winch ---1,451 544 ---1,994 ---1,659 208Remove 600 ft of wire rope --- auxiliary winch ---1,031 590 ---1,621 ---1,382 352Substitute 600 ft of wire rope with 850 ft of wirerope --- auxiliary winch 420 ---240 660 563 ---143
360˚ mechanical swing lock 136 52 84 52 84Air conditioning 76 37 39 21 55Auxiliary lifting sheave 120 362 ---242 ---269 389Boom floodlight 7 18 ---11 ---13 20Fly mounting brackets to boom base for fly options 290 508 ---218 ---285 57531---55 ft offsettable, two piece bi---fold fly --- stowed 2,734 4,667 ---1,933 ---2,565 5,29910---31---55 ft offsettable, three piece bi---fold fly ---stowed 3,331 6,077 ---2,746 ---3,516 6,847
10---31---55 ft hydraulically offsettable, three piecebi---fold fly --- stowed 3,804 7,338 ---3,534 ---4,414 8,218
Additional components for hydraulicallyoffsettable fly 469 990 ---521 ---629 1,098
12 ton swivel hook ball (stowed at front/rearbumper) 722 1,153 ---431 ---598 1,320
12 ton swivel hook ball (stowed at boom head) 722 2,092 ---1,370 ---1,537 2,25935 ton 1---sheave hook block (stowed at front/rearbumper) 1,100 1,756 ---656 ---911 2,011
35 ton 1---sheave hook block (stowed at boomhead) 1,100 3,188 ---2,088 ---2,342 3,442
80 ton 5---sheave hook block (stowed at front/rearbumper) 1,411 2,253 ---842 ---1,168 2,579
80 ton 5---sheave hook block (stowed at boomhead) 1,411 4,089 ---2,678 ---3,004 4,415
100 ton 6---sheave hook block (stowed at front/rearbumper) 1,750 2,794 ---1,044 ---1,449 3,199
100 ton 6---sheave hook block (stowed at boomhead) 1,750 5,071 ---3,321 ---3,726 5,476
140 ton 7---sheave hook block (stowed at front/rearbumper) 2,394 3,822 ---1,428 ---1,982 4,376
140 ton 7---sheave hook block (stowed at boomhead) 2,394 6,938 ---4,544 ---5,097 7,491
Tire Maximum Load @ 20 mph
23.5R25 57,330 lb
(1) Adjust gross vehicle weight and axle loading according to component weight.Note: All weights are ±3%.
8 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
Axle Loads -- Metric
Base machine with full tank of fuel and13 154.1kg of counterweight
Gross VehicleWeight (1)
Upper Facing Front Upper Facing RearFront Axle Rear Axle Group Front Axles Rear Axle Group
(1) Adjust gross vehicle weight and axle loading according to component weight.Note: All weights are ±3%.
95567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
Transport Configuration and Weights
C
BCrane Weight: 93,748 lb (42 523kg), equipped with:S 41.4---162 ft (12.6 ---49.3m), five section boomS 80 ton (72.57mt) hook blockS Main winch with 850 ft (259.1m) of 7/8 in (22mm) ropeS Auxiliary winch with 600 ft (182.8m) of 7/8 in (22mm) ropeS 10---31---55 ft (3.0 ---9.4 ---16.7m) offsettable, three piece bi---fold flyS Hoist drum followers --- Main and AuxiliaryS Auxiliary lifting sheaveS Air conditioningS Hydraulic outrigger pin removal
Drop Off Load Weight: 44,478 lb (20 175kg)S Two outrigger boxes with tow shacklesS 27,000 lb (13 154.1kg) counterweightS 12 ton (10.9mt) hook ball
Normal Suspension Collapsed SuspensionC [with 18 in (0.46m) Trailer] 13 ft 11 in (4.24m) 13 ft 8 in (4.16m)C [with 24 in (0.61m) Trailer] 14 ft 5 in (4.39m) 14 ft 2 in (4.32m)
A
General Dimensions
15.0”(0.38m) 16.4”
(0.42m)
20.3”(0.52m)
5’ 9”(1.75m)
Turning Radius --- 2 Wheel Steering English MetricWall to wall over carrier 44’ 10” 13.67mWall to wall over boom attachment 56’ 0” 17.07mCurb to curb 41’ 5” 12.62mCenterline of tire 40’ 4” 12.29m
Turning Radius --- 6 Wheel Steering English MetricWall to wall over carrier 25’ 5” 7.75mWall to wall over boom attachment 38’ 9” 11.81mCurb to curb 21’ 10” 6.66mCenterline of tire 20’ 9” 6.32m
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
155567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
43,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
Radius(ft)
Main Boom + 10 ft Manual Offset Fly (2˚, 15˚, 30˚, 45˚ Offsets)Radius(ft)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
16 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
29,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
175567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
43,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
18 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
29,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
162 ft Main Boom Length
Radius(ft)
73 ft Manual Offset Fly 91 ft Manual Offset Fly 109 ft Manual Offset Fly Ra-dius(ft)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
195567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
43,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
162 ft Main Boom Length
Radius(ft)
73 ft Manual Offset Fly 91 ft Manual Offset Fly 109 ft Manual Offset Fly Ra-dius(ft)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capaci-ties shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
215567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
43,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
Main Boom + 10 ft Hydraulic Offset Fly (2˚ ---45˚ Offsets)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capaci-ties shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
22 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
29,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capaci-ties shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
235567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
43,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capaci-ties shown on fully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
24 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
29,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
255567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
43,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
26 5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
On Tires Lift Capacity Charts -- Standard26,000 lb Counterweight -- On Tires -- Stationary -- Boom Centered Over Rear Between Tire Tracks
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
275567 (supersedes 5561)---0210---R3
RTC---80130 IILink-Belt Cranes
26,000 lb Counterweight -- On Tires -- Pick & Carry (Creep) -- Boom Centered Over Rear(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
5567 (supersedes 5561)---0210---R3
RTC---80130 II Link-Belt Cranes
Link--Belt Construction Equipment Company Lexington, Kentucky www.linkbelt.comRLink--Belt is a registered trademark. Copyright 2010. We are constantly improving our products and therefore reserve the right to change designs and specifications.