BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Center, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0)1902 404736 Fax: +44 (0)1902 403906 email: [email protected]Series 4 High Temperature Bellows Sealed Valve Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection. ASME III option available. Straight Pattern shown, also available as Angle pattern and Oblique pattern. Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suit- able materials for the temperature, pressure and media. Dimensions Valve Size Dim Dim Dim Weight Cv DN A mm B mm C mm Kg IGPM DN8 108 241 100 9 1.7 DN15 108 241 100 9 2.45 DN20 117 241 100 9 2.45 DN25 127 254 100 9.6 5.8 DN40 165 368 150 24 12.4 DN50 203 400 150 25 18.5 Material Specification Body Bonnet Seat Disk Stem Bellows Back up Gland Yoke Bush Stainless Steel Valve St.St. ASTM A182 F316H St.St. ASTM A182 F316H Integral Hard Faced St. St. - Hard Faced St.St. ASTM A182 F316H Incolloy 800H or 800HT Exfoliated Graphite Aluminium Bronze Service Service T emperature Pressure ºC bar g 38 103.4 50 101.6 100 94.2 200 79.6 300 70.6 400 65.7 500 63.4 600 49.8 700 22.8 800 8.8 816 7.2 09.18.14 Page 1 of 18
18
Embed
Series 4 High Temperature Bellows Sealed Valve · Bolted Bonnet Valve - Angle Pattern Class 800/900/1500 bellows sealed globe valve to BS5352, standard bore, outside screw and yoke,
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Center, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0)1902 404736 Fax: +44 (0)1902 403906 email: [email protected]
Series 4 High Temperature Bellows Sealed Valve Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection. ASME III option available. Straight Pattern shown, also available as Angle pattern and Oblique pattern.
Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed.
Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suit- able materials for the temperature, pressure and media.
Dimensions
Valve Size Dim Dim Dim Weight Cv DN A mm B mm C mm Kg IGPM
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 34A Bolted Bonnet Valve - Straight Pattern
Class 800/900/1500 bellows sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.
Nuclear versions to ASME III available.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.
Carbon Steel Valve Stainless Steel Valve Body C.St. ASTM A105 St.St. Type 316L Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or integral Stellite HF
St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF
St.St. Type 410 or Stellite HF
Stem St.St. Type 316L St.St. Type 316L Bellows St.St. Type 316L St.St. Type 316L Back up Gland Exfoliated graphite Exfoliated graphite Yoke Bush Aluminium bronze Aluminium bronze
09.18.14 Page 2 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 34B Bolted Bonnet Valve - Oblique Pattern
Class 600/900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available. Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks. Cartridge valve, version also available - seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperatures up to 320 oC. Materials can be changed to customer specifications.
Dimensions Size Dim A Dim B Weight Cv DN mm mm Kg UKGPM 6 229 242 13 2 15 229 242 13 5.8 20 229 245 13 5.8 25 254 260 15.5 11 40 305 350 35 30 50 368 420 40 54 80 381 540 250 153
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 34C Bolted Bonnet Valve - Angle Pattern
Class 800/900/1500 bellows sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.
Nuclear versions to ASME III available.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.
Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.
Dimensions (typical)
Class 800 Class 900/1500
Valve Size DN
Dim A mm
Dim B mm
Dim C mm
Weight Kg
Cv UK
Gal/min
Dim A mm
Dim B mm
Dim C mm
Weight Kg
Cv UK
Gal/min DN6 57 241 100 9 2.7 108 321 150 12 2.7
DN15 57 241 100 9 3.9 108 321 150 12 3.9
DN20 64 241 100 9 3.9 114 321 150 12 3.9
DN25 70 254 100 9.6 9.2 127 384 150 15 9.2
DN40 83 368 150 24 19.8 152 458 200 30 19.8
DN50 102 400 150 25 29.6 184 530 290 35 29.6
Component Material
Carbon Steel Valve Stainless Steel Valve Body C.St. ASTM A105 St.St. Type 316L Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or integral Stellite HF
St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF
St.St. Type 410 or Stellite HF
Stem St.St. Type 316L St.St. Type 316L Bellows St.St. Type 316L St.St. Type 316L Back up Gland Exfoliated graphite Exfoliated graphite Yoke Bush Aluminium bronze Aluminium bronze
09.18.14 Page 4 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 35A Seal Welded Bonnet Valve - Straight Pattern
Seal Welded Bonnet Valve - Straight Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet. To ANSI B16.34 or Nuclear Class to ASME III
Available with Integral Hard Faced (Stellite 6 or Colomonoy 5) Seat or Screwed in Stainless Steel Seat
Valve can be supplied with Actuator - Electric or Pneumatic.
Buttweld end connections shown, also available as screwed, socket weld, flanged or special connection
Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media. DN65/DN80/DN100 normally cast body and bonnet. Forged available.
Dimensions are subject to confirmation. Drawings with confirmed dimensions can be supplied at time of order.
Material Specification
Carbon Steel Valve Stainless Steel Valve Body & Bonnet
C.St. ASME SA350 LF2 or C.St. ASME SA352 LCB
St.St. ASME SA182 F316L or St.St. ASME SA351 CF3M
Seat Integral Hard Facing Integral Hard Facing
Disk St.St. Type 316L with Hard Facing St.St. Type 316L with Hard Facing
Stem St. St. ASME SA564 630 H1075 St. St. ASME SA564 630 H1075
Bellows Inconel 600/625 Inconel 600/625
Gland Exfoliated Graphite Exfoliated Graphite
Bush Aluminium Bronze Aluminium Bronze
09.18.14 Page 5 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 35B Seal Welded Bonnet Valve - Oblique Pattern
Seal Welded Bonnet Valve - Oblique Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet.
Available with Integral Hard Faced Seat to offer increased resistance against corrosion.
Valve can be supplied with Actuator - Electric or Pneumatic.
Buttweld end connections shown, also available as screwed, socket weld, flanged or special connection
Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.
Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352.
Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.
Dimensions are subject to confirmation. Drawings with confirmed dimensions can be supplied at time of order.
Carbon Steel Valve Stainless Steel Valve Body & Bonnet
C.St. ASTM A105 St.St. BS1503 304S11
Seat St.St. Type 410 or Integral Stellite Hard Facing
St.St. Type 410 or Integral Stellite Hard Facing
Disk St.St. Type 410 or Stellite Hard Facing
St.St. Type 410 or Stellite Hard Facing
Stem St. St. Type 304 St. St. Type 304
Bellows St. St. Type 304 St. St. Type 304
Gland Exfoliated Graphite Exfoliated Graphite
Bush Aluminium Bronze Aluminium Bronze
09.18.14 Page 6 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 35C Seal Welded Bonnet Valve - Angle Pattern
Seal Welded Bonnet Valve - Angle Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet. To ANSI B16.34 or Nuclear Class to ASME III
Available with Integral Hard Faced (Stellite 6 or Colomonoy 5) Seat or Screwed in Stainless Steel Seat
Valve can be supplied with Actuator - Electric or Pneumatic.
Buttweld end connections shown, also available as screwed, socket weld, flanged or special connection
Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media. DN65/DN80/DN100 normally cast body and bonnet. Forged available.
Dimensions (typical)
Class 150/300/600 Class 900/1500
Valve Size DN
Dim A mm
Dim B mm
Dim C mm
Weight Kg
Cv UK
Gal/min
Dim A mm
Dim B mm
Dim C mm
Weight Kg
Cv UK
Gal/min DN6 57 243 100 16 2.7 108 261 150 12 2.7
DN15 57 243 100 16 3.9 108 261 150 12 3.9
DN20 64 243 100 16 3.9 114 261 150 12 3.9
DN25 70 256 125 20 9.2 127 294 150 14 9.2
DN40 83 368 150 33 19.8 152 398 200 28 19.8
DN50 102 400 200 39 29.6 184 440 250 30 29.6
DN65 108 450 300 220 73 210 500 300 180 60
DN80 121 500 300 260 110 235 560 300 200 100
DN100 146 521 300 350 204 273 590 300 290 180
Dimensions are subject to confirmation. Drawings with confirmed dimensions can be supplied at time of order.
Material Specification
Carbon Steel Valve Stainless Steel Valve Body & Bonnet
C.St. ASME SA350 LF2 or C.St. ASME SA352 LCB
St.St. ASME SA182 F316L or St.St. ASME SA351 CF3M
Seat Integral Hard Facing Integral Hard Facing
Disk St.St. Type 316L with Hard Facing St.St. Type 316L with Hard Facing
Stem St. St. ASME SA564 630 H1075 St. St. ASME SA564 630 H1075
Bellows Inconel 600/625 Inconel 600/625
Gland Exfoliated Graphite Exfoliated Graphite
Bush Aluminium Bronze Aluminium Bronze
09.18.14 Page 7 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 36A Bolted/Edge Welded Bonnet Valve - Straight Pattern
Class 900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, bolted and lip-seal welded bonnet. ASME III option available. Secondary gland in the event of bellows failure. Available with integral hard faced seat to offer increased resistance against erosion Valve can be supplied with manual operation or actuated - electric or pneumatic. Manual valve and electrically actuated valve shown.
Valve shown is with a leak detection port, to provide early warning of any bellows failure. Extended spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically actuated valves are available.
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 36B Bolted/Edge Welded Bonnet Valve - Oblique Pattern
Class 900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, bolted and lip-seal welded bonnet. ASME III option available. Secondary gland in the event of bellows failure. Available with integral hard faced seat to offer increased resistance against erosion Valve can be supplied with manual operation or actuated - electric or pneumatic. Manual valve and electrically actuated valve shown.
Valve shown is with a leak detection port, to provide early warning of any bellows failure. Extended spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically actuated valves are available.
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 36C Bolted/Edge Welded Bonnet Valve - Angle Pattern
Class 900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, bolted and lip-seal welded bonnet. ASME III option available. Secondary gland in the event of bellows failure. Available with integral hard faced seat to offer increased resistance against erosion Valve can be supplied with manual operation or actuated - electric or pneumatic. Manual valve and electrically actuated valve shown.
Valve shown is with a leak detection port, to provide early warning of any bellows failure. Extended spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically actuated valves are available.
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 40A Bolted Bonnet Cartridge Valve - Straight Pattern
Class 600 bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available. Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks.
Cartridge valve, seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperatures up to 320 oC. Materials can be changed to customer specifications.
Dimensions Size Dim A Dim B Weight Cv DN mm mm Kg UKGPM 6 108 243 9 1.7 15 108 243 9 2.45 20 117 243 9 2.45 25 127 256 9.6 5.8 40 165 368 24 12.4 50 203 400 25 18.5 80 356 500 202 37 100 406 521 240 76 150 559 780 278 260
Component MaterialBody St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Seat St.St. BSEN 10088-3 1.4307 / ASME SA479 304L Seat Seal Perlast or Kalrez seal Disk St.St. BSEN 10088-3 1.4307 / ASME SA479 304L Stem St.St. BSEN 10088-3 1.4307 Bellows St.St. Type 316L Back up Gland Graphite
09.18.14 Page 11 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 40B Bolted Bonnet Cartridge Valve - Oblique Pattern
Bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available. Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks.
Cartridge valve, seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperatures up to 320 oC. Materials can be changed to customer specifications.
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 40C Bolted Bonnet Cartridge Valve - Angle Pattern
Bellows Sealed Angle Pattern Globe Valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available. Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks. Cartridge valve, seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted. Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperatures up to 320 oC. Materials can be changed to customer specifications.
Dimensions Size Dim A Dim B Dim C Dim D Dim E Weight DN mm mm mm mm mm Kg 8 45 200 32 101 102 8 15 57 218 32 101 102 12 20 64 230 32 101 102 12 25 70 230 32 127 102 12 40 83 235 43 155 128 21 50 102 255 51 155 165 26 80 178 482 104 254 220 202 100 203 502 114 254 240 275 150 279 770 139 450 278 355
Component MaterialBody St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Seat St.St. BSEN 10088-3 1.4307 / ASME SA479 304L Seat Seal Perlast or Kalrez seal Disk St.St. BSEN 10088-3 1.4307 / ASME SA479 304L Stem St.St. BSEN 10088-3 1.4307 Bellows St.St. Type 316L Back up Gland Graphite
09.18.14 Page 13 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 50A Non-Bellows Sealed Valve - Straight Pattern Globe
Straight Pattern Globe Class 800 gland sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.
Nuclear versions to ASME III available.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.
Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.
Dimensions Size Dim A Dim B Dim C Weight Cv DN mm mm mm Kg UKGPM 6 108 241 100 9 1.7 15 108 241 100 9 2.45 20 117 241 100 9 2.45 25 127 254 100 9.6 5.8 40 165 368 150 24 12.4 50 203 400 150 25 18.5
Component Material
Carbon Steel Valve Stainless Steel Valve Body C.St. ASTM A105 St.St. Type 316L Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or integral Stellite HF
St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF
St.St. Type 410 or Stellite HF
Stem St.St. Type 316L St.St. Type 316L Back up Gland Exfoliated graphite Exfoliated graphite Yoke Bush Aluminium bronze Aluminium bronze
09.18.14 Page 14 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 50B Bolted Bonnet Valve - Oblique Pattern
Class 600/900/1500 gland sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available. Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks. Cartridge valve, version also available - seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.. Materials can be changed to customer specifications.
Dimensions Size Dim A Dim B Weight Cv DN mm mm Kg UKGPM 6 229 242 13 2 15 229 242 13 5.8 20 229 245 13 5.8 25 254 260 15.5 11 40 305 350 35 30 50 368 420 40 54 80 381 540 250 153
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 50C Non-Bellows Sealed Valve - Angle Pattern Globe
Angle Pattern Globe Class 800 gland sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.
Nuclear versions to ASME III available.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.
Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.
Dimensions Size Dim A Dim B Dim C Weight Cv DN mm mm mm Kg UKGPM 6 57 241 100 9 2.7 15 57 241 100 9 3.9 20 64 241 100 9 3.9 25 70 254 100 9.6 9.240 83 368 150 24 19.8 50 102 400 150 25 29.6
Component Material
Carbon Steel Valve Stainless Steel Valve Body C.St. ASTM A105 St.St. Type 316L Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or integral Stellite HF
St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF
St.St. Type 410 or Stellite HF
Stem St.St. Type 316L St.St. Type 316L Back up Gland Exfoliated graphite Exfoliated graphite Yoke Bush Aluminium bronze Aluminium bronze
09.18.14 Page 16 of 18
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 50D Non-Bellows Sealed Valve - Straight Pattern Non-Return
Class 800 non-return valve to BS5352, standard bore, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.
BVMI Process Engineering Office 5/6, 3rd Floor, The Saturn Centre, Spring Road, Ettingshall, Wolverhampton, WV4 6JX, UK Tel: +44 (0) 1902 404736 Fax: +44 (0) 1902 403906 email: [email protected]
Series 55A Instrument Valve - Straight Pattern
Class 600 bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, union bonnet Available with integral seat or screwed in stainless steel seat or soft seated with O ring in disk Valve can be supplied with pneumatic actuator Butt weld end connections shown, also available as screwed, socket weld, flanged or any special connection.
Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.
Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.st. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.
Dimensions Size Dim A Dim B Dim C Weight DN mm mm mm Kg 6 101.6 180 100 3.5 10 101.6 180 100 3.5 15 108 190 100 4 20 117 195 100 4 25 127 200 100 4.5
Component MaterialBody St.St. Type 316L Bonnet St.St. Type 316L Seat St.St. Type 316L or integral Disk St.St. Type 316L with/without Viton seal Stem St.St. Type 316L Gland Bush St.St. Type 316L Back up Gland PTFE Yoke Bush Aluminium Bronze