S.D.M COLLEGE OF ENGINEERING AND TECHNOLOGYsdmcse2006.pbworks.com/f/2sd06cs085.pdf · 2010-03-17 · or qudrature amplitude modulation (QAM). In the following example, all subcarriers

1

VISHVESHWARAIAH TECHNOLOGICAL UNIVERSITY

S.D.M COLLEGE OF ENGINEERING AND TECHNOLOGY

A seminar report on

Orthogonal Frequency Division Multiplexing

(OFDM)

Submitted by

Sandeep Katakol

2SD06CS085 8th semester

DEPARTMENT OF COMPUTER SCIENCE ENGINEERING 2009-10

2

VISHVESHWARAIAH TECHNOLOGICAL UNIVERSITY

S.D.M COLLEGE OF ENGINEERING AND TECHNOLOGY

DEPARTMENT OF COMPUTER SCIENCE ENGINEERING

CERTIFICATE

Certified that the seminar work entitled “Orthogonal Frequency Division Multiplexing (OFDM)” is a bonafide work presented by Sandeep Katakol bearing USN NO:2SD06CS085 in a partial fulfillment for the award of degree of Bachelor of Engineering in Computer Science Engineering of the Vishveshwaraiah Technological University, Belgaum during the year 2009-10. The seminar report has been approved as it satisfies the academic requirements with respect to seminar work presented for the Bachelor of Engineering Degree.

Staff in charge H.O.D

CSE

Name: Sandeep Katakol

3

USN: 2SD06CS085

INDEX

1. INTRODUCTION 4

2. MULTIPLEXING 4

2.1 TDMA 5

2.2 CDMA 5

2.3 FDMA 6

3. OFDM 6

4. DATA TRANSMISSION USING MULTIPLE CARRIERS 8

5. GUARD TIME AND CYCLIC EXTENTION 10

6. TRANSMISSION AND RECEPTION 10

7. CHOICE OF OFDM PARAMETERS 11

8. ADVANTAGES 12

9. DISADVANTAGES 14

10. CONCLUSION 14

4

Orthogonal Frequency Division Multiplexing

(OFDM)

ABSTRACT A number of new technologies are being combined by the telecommunications

industry as it prepares for the next generation of mobile services. One of the key changes

is the choice of OFDM for the air interface. This paper will describe OFDM and show

why it has the ability to improve the spectral efficiency of digital radio links Orthogonal

frequency division multiplexing (OFDM) is a special case of multicarrier transmission,

where a single datastream is transmitted over a number of lower rate subcarriers.

1. INTRODUCTION In today’s world cell phone have become the single greatest tool in day today life. It has become

a necessity that business associates should be able to communicate on the go. That’s why it has become

so important to make choices in choosing which handheld device one should go for. A handheld device

is selected according to its features and benefits, like does it provide access to internet and email or does

it look slick and more. An important question when designing and standardizing cellular systems is the

selection of the multiple access schemes. There are three basic principles in multiple access, FDMA

(Frequency Division Multiple Access), TDMA (Time Division Multiple Access), and CDMA (Code

Division Multiple Access). All three principles allow multiple users to share the same physical channel

Orthogonal frequency division multiplexing (OFDM) is a communications technique that divides

a communications channel into a number of equally spaced frequency bands. A subcarrier carrying a

portion of the user information is transmitted in each band. Each subcarrier is orthogonal (independent

of each other) with every other subcarrier, differentiating OFDM from the commonly used frequency

division multiplexing (FDM).

2. MULTIPLEXING Multiplexing is the set of techniques that allows the simultaneous transmission of multiple

signals across a single data link. As data and telecommunications use increases, so does traffic. We can

accommodate. This increase by continuing to add individual links each time a new channel is needed.

In a multiplexed system, n lines share the bandwidth of one link. Figure shows the basic format

of a multiplexed system. The lines on the left direct their transmission streams to a multiplexer (MUX),

which combines them into a single stream (many-to- one).

At the receiving end, that stream is fed into a demultiplexer (DEMUX), which separates the stream

back into its component transmissions (one-to-many) and directs them to their corresponding lines. In

the figure, the word link refers to the physical path. The word channel refers to the portion of a link that

carries a transmission between a given pair of lines. One link can have many (n) channels.[1]

5

2.1 TDMA: Time Division Multiplex Access is a type of multiplexing where two or more channels of

information are transmitted over the same link by allocating a different time interval for the transmission

of each channel.

One major disadvantage using TDMA technology is that the users has a predefined time slot.

When moving from one cell site to other, if all the time slots in this cell are full the user might be

disconnected. Another problem in TDMA is that it is subjected to multipath distortion.[1]

2.2 CDMA CDMA gives the user entire spectrum all of the time. CDMA spread spectrum technology in

which it uses unique spreading codes to spread the baseband data before transmission. The receiver then

dispreads the wanted signal, which is passed through a narrow band pass filter. The unwanted signals are

not dispread and will not be passed through the filter. The codes are a sequence of zeros and ones

produced at a much higher rate of that of the baseband data.

One major problem in CDMA technology is channel pollution, where signals from too many cell

sites are present in the subscriber’s phone but none of them is dominant. When this situation arises the

quality of the audio degrades[1]

6

2.3 FDMA

In frequency-division multiple access (FDMA), the available bandwidth is divided into

frequency bands. Each station is allocated a band to send its data. In other words, each band is reserved

for a specific station, and it belongs to the station all the time. FDMA specifies a predetermined

frequency band for the entire period of communication. This means that stream data (a continuous flow

of data that may not be packetized) can easily be used with FDMA. [1]

3. OFDM

OFDM represents a different system-design approach. It can be thought of as a combination of

modulation and multiple-access schemes that segments a communications channel in such a way that

many users can share it. Whereas TDMA segments are according to time and CDMA segments are

according to spreading codes, OFDM segments are according to frequency. It is a technique that divides

the spectrum into a number of equally spaced tones and carries a portion of a user's information on each

tone. A tone can be thought of as a frequency, much in the same way that each key on a piano represents

a unique frequency. OFDM can be viewed as a form of frequency division multiplexing (FDM),

however, OFDM has an important special property that each tone is orthogonal with every other tone.

FDM typically requires there to be frequency guard bands between the frequencies so that they do not

7

interfere with each other. OFDM allows the spectrum of each tone to overlap, and because they

areorthogonal, they do not interfere with each other. By allowing the tones to overlap, the overall

amount of spectrum required is reduced.

OFDM is a modulation technique in that it enables user data to be modulated onto the tones. The

information is modulated onto a tone by adjusting the tone's phase, amplitude, or both. In the most basic

form, a tone may be present or disabled to indicate a one or zero bit of information, however, either

phase shift keying (PSK) or quadrature amplitude modulation (QAM) is typically employed.

An OFDM system takes a data stream and splits it into N parallel data streams, each at a rate 1/N

of the original rate. Each stream is then mapped to a tone at a unique frequency and combined together

using the inverse fast fourier transform (IFFT) to yield the time-domain waveform to be transmitted.

For example, if a 100-tone system were used, a single data stream with a rate of 1 megabit per second

(Mbps) would be converted into 100 streams of 10 kilobits per second (kbps). By creating slower

parallel data streams, the bandwidth of the modulation symbol is effectively decreased by a factor of

100, or, equivalently, the duration of the modulation symbol is increased by a factor of 100. Proper

8

selection of system parameters, such as the number of tones and tone spacing, can greatly reduce, or

even eliminate, ISI, because typical multipath delay spread represents a much smaller proportion of the

lengthened symbol time. Viewed another way, the coherence bandwidth of the channel can be much

smaller, because the symbol bandwidth has been reduced. The need for complex multi-tap time-domain

equalizers can be eliminated as a result.

OFDM can also be considered a multiple-access technique, because an individual tone or groups

of tones can be assigned to different users. Multiple users share a given bandwidth in this manner,

yielding the system called OFDMA. Each user can be assigned a predetermined number of tones when

they have information to send, or alternatively, a user can be assigned a variable number of tones based

on the amount of information that they have to send. The assignments are controlled by the media access

control (MAC) layer, which schedules the resource assignments based on user demand. OFDM can be

combined with frequency hopping to create a spread spectrum system, realizing the benefits of

frequency diversity and interference averaging previously described for CDMA. In a frequency hopping

spread spectrum system, each user's set of tones is changed after each time period (usually

corresponding to a modulation symbol). By switching frequencies after each symbol time, the losses due

to frequency selective fading are minimized. Although frequency hopping and CDMA are different

forms of spread spectrum, they achieve comparable performance in a multipath fading environment and

provide similar interference averaging benefits.

OFDM therefore provides the best of the benefits of TDMA in that users are orthogonal to one

another, and CDMA, as previously mentioned, while avoiding the limitations of each, including the need

for TDMA frequency planning and equalization, and multiple access interference in the case of CDMA.

4. DATA TRANSMISSION USING MULTIPLE CARRIERS An OFDM signal consists of a sum of subcarriers that are modulated by using phase shift keying (PSK)

or qudrature amplitude modulation (QAM). In the following example, all subcarriers have the phase

and amplitude, but in practice the amplitudes and phases may be modulated differently for each

subcarrier. Note that each subcarrier has exactly an integer number of cycles in the interval T , and the

number of cycles between adjacent subcarries differs by exactly one. This properly accounts for the

orthogoality between subcarriers.

9

The orthogonality of different OFDM subcarriers can also be demonstrated in another way.If each

OFDM symbol contains subcarriers that are nonzero over a T -seconds interval.Then it has which has

zeros for all frequencies f that are an integer multiple of 1/T . This effect is shown in figure which

shows the overlapping sinc spectra of individual subcarriers. At the maximum of each subcarrier

spectrum, all other subcarrier spectra are zero. Because an OFDM receiver calculates the spectrum

values at those points that correspond to the maxima of individual subcarrier, it can demodulate each

subcarrier free from any interference from the other subcarriers. Basically, below Figure shows that the

OFDM spectrum fulfills Nyquist’s criterion for an inter symbol interference free pulse shape. Notice

that the pulse shape is present in frequency domain and note in the time domain, for which the Nyquist

criterion usually is applied. Therefore, instead of intersymbol interference (ISI), it is intercarrier

interference (ICI) that avoided by having the maximum of one subcarrier spectrum correspond to zero

crossing of all the others

10

5. GUARD TIME AND CYCLIC EXTENTION

One of the most important reasons to do OFDM is the efficient way it deals with multipath delay

spread. By dividing the input data stream in N subcarriers, the symbol duration is made N times smaller,

which also reduces the relative multipath delay spread, relative to symbol time, by the same factor. To

eliminate intersymbol interference almost completely, a guard time is introduced for each OFDM

symbol. The guard time is chosen larger than the expected delay spread, such that multipath components

from one symbol cannot interfere with the next symbol. The guard time could consist of no signal at all.

In that case, however, the problem of intercarrier (ICI) would arise. ICI is crosstalk between different

subcarriers,which means they are no longer orthogonal. This effect is illustrated in figure in this

example, a subcarrier 1 and a delayed subcarrier 2 are shown. When an OFDM receiver tries to

demodulate the first subcarrier, it will encounter some interference from the second subcarrier, because

within the FFT interval, there is no integer number of cycles difference between subcarrier 1and 2. At

the same time, there will be crosstalk from the first to the second subcarrier for the same reason. To

eliminate ICI, the OFDM symbol is cyclically extended in the guard time, as shown in figure. This

ensures that delayed replicas of the OFDM symbol always have an integer number of cycles within the

FFT interval, as long as the delay is smaller than the guard time. As result, multipath signals with delays

smaller than the guard time cannot cause ICI.

11

6. TRANSMISSION AND RECEPTION

OFDM modulation divides a broadband channel into many parallel subchannels. This makes it a

very efficient scheme for transmission in multipath wireless channels. The use of an FFT/IFFT pair for

modulation and demodulation make it computationally efficient as well.

12

The transmitted signals arrive at the receiver after being reflected from many objects. Sometimes

the reflected signals add up in phase and sometimes they add up out of phase causing a “fade”. This

causes the received signal strength to fluctuate constantly. Also, different subchannels are distorted

differently as shown in Figure . An OFDM receiver has to sense the channel and correct these distortions

on each of the subchannels before the transmitted data can be extracted. OFDM is effective in correcting

such frequency selective distortions. OFDM has many advantages over other transmission techniques.

One such advantage is high spectral efficiency (measured in bits/sec/Hz). The “Orthogonal” part of the

name refers to a precise mathematical relationship between the frequencies of the subchannels that make

up the OFDM system. Each of the frequencies is an integer multiple of a fundamental frequency. This

ensures that even though the subchannels overlap they do not interfere with each other. This results in

high spectral efficiency. The use of IFFT and FFT for modulation and demodulation results in

computationally efficient OFDM modems.[3]

13

7. CHOICE OF OFDM PARAMETERS The choice of various OFDM parameters is a tradeoff between various, often conflicting

requirements. Usually, there are three main requirements to start with: bandwidth, bit rate, and delay

spread. The delay spread directly dictates the guard time. As a rule, the guard time should be about two

to four times the root-mean-squared delay spread. This value depends on the type of coding and QAM

modulation. Higher order QAM (like 64-QAM) is more sensitive to ICI and ISI than QPSK; while

heavier coding obviously reduces the sensitivity to such interference. Now the guard time has been set,

the symbol duration can be fixed. To minimize the signal-to-noise ratio (SNR) loss caused by guard

time, it is desirable to have the symbol duration much larger than the guard time. It cannot be arbitrarily

large, however, because a larger symbol duration means more subcarriers with a smaller subcarrier

spacing, a larger implementation complexity, and more sensitivity to phase noise and frequency offset,

as well as an increased peak-to-average power ratio. Hence, a practical design choice to make the

symbol duration at least five times the guard time, which implies a 1dB SNR loss because the guard

time. After the symbol duration and guard time are fixed, the number of subcarriers follows directly as

the required –3 dB bandwidth divided by the subcarrier spacing,which is the inverse of the symbol

duration less the guard time. Alternatively, the number of subcarriers may be determined by the required

bit rate divided by the bit rate per subcarrier. The bit rate per subcarrier is defined by the modulation

type, coding rate, and symbol rate. An additional requirement that can affect the chosen parameters is

the demand for an integer number of samples both within the FFT/IFFT interval and in the symbol

interval.

8. ADVANTAGES Efficient use of spread spectrum in modulation.

It is conveniently implemented using simple FFT and IFFT.

Robust against multi-path propagation.

Robust again narrow-band interference

14

9. DISADVANTAGES Requires a more linear power amplifier.

Sensitive to frequency offset and phase noise

Accurate synchronization is required.

10. CONCLUSION This report describes the concept of OFDM with brief description of other multiplexing

technologies.It also describes data transmission in OFDM,Guard time,Cyclic prefix, Transmission and

reception techniques,and some advantages and disadvantages of OFDM.

Wireless LAN is a very important application for OFDM and the development of the standard promises

to have not only a big market but also application in many different environments.

REFERENCES [1] Data Communications and Networking - Behrouz A. Forouzan

[2] Concepts of Orthogonal Frequency Domain Modulation (OFDM)

By Dave Whipple, Agilent Technologies

[3] http://www.mimo.ucla.edu/ The Engineer’s introduction to mimo and

Mimo-ofdm

[4] The principles of OFDM By Louis Litwin and Michael Pugel