ScrapMaster - SalvajorModel SM & Model PSM Specifications 208V 230V 460V, 60 Cycle, 3 Phase Disposer3-5 HP - 230208460V Pump ¾ HP -230208460V Separator1⁄ 6 HP -230208460V VOLTAGES

Job: Item No.:

Job: Item No.: TYPICAL INSTALLATIONS

A Scrapping, Pre-Flushingand Disposing System with:

n Standard Scrap Basin, Model SM n Pot/Pan Scrap Basin, Model PSMRecirculated Water used by the system for pre-flushing will reduce water and sewer cost by thousands of dollars per year. The ScrapMaster consumes only 7 gallons of new water per minute while the heavy pre-flushing plume recirculates at a 30 gallon rate.Scrapping Speed is more than doubled by a single operator as both hands are used for scrapping. The ScrapMaster’s powerful plume of water takes the place of a less productive pre-rinse spray.Problem Dishes, Trays and Cookware with dried or baked-on food need much less hand work as they can be soaking in the scrap basin while the scrapping process continues. Design Flexibility of the ScrapMaster allows the pre-flushing and scrapping of all types of soiled tableware and cookware. The standard scrap basin accepts all soiled tableware as well as school trays. The pot/pan scrap basin accommodates dishes, school trays, pots, pans and even 26 inch sheet pans.Less Splashing occurs with the ScrapMaster water plume compared to a pre-rinse spray. HydroLogic Control Panel saves water and energy. Includes patented operator sensing technology with water saving mode.

Model SM

Model PSM

Model PSM

Model SM

U.S. Pat. No. 7,815,134

ScrapMaster®

ScrapMaster® Model SM

FG

B

B

A

A

G

D

C

E

E

F

39"(99.06)

12"(30.48)

22"(55.88)

39"(99.06)

18 15/16"(48.06)

18 7/8"(47.94)

18 7/8"(47.98)

1 1/2"(3.77)

7 1/4"(18.48)

7 1/2"(19.05)

5 7/16"(13.81)

22 15/16"(58.29)

14 1/4"(36.19)

20 1/4"(51.38)

8 3/4"(22.26)

2 3/4"(6.99) 11 1/2"

(29.21) 19 5/8"(49.85)

20"(50.80)

9"(22.86)

5 5/16"(13.49)

16 1/2"(41.91)

10 9/16"(26.83)

36 5/8"(93.03)

20 11/16"(52.59)

28 11/16"(72.90)

33 3/16"(84.30)Adjustable to36 3/16"(91.92)

Table cutout detail

F

SM & PSM Legend Disposer outlet can be rotated at most any angle by rotating disposer. Rubber drain accepts 2” piping or 3” piping by removing drain insert.

Tank reservoir drain – Plumb 2” piping from valve to floor drain or connect to disposer drain piping ahead of P trap.

Disposer electrical connection.

Disposer to control connection.

Incoming electrical connection.

Hot and cold water connection. 1/2” NPT

Recirculating water valve.

A

B

C

DE

F

G

NOTE: Dimensions in parenthesis are in centimeters

All connections are to be made byqualified personnel who will observe

all local and national codes.

Model SM Drain Piping2” tank reservoir drain can be run separately or

be tied in with 2”-3” disposer drain.

Pot/Pan ScrapMaster® Model PSM

FG

B

B

A

A

E

E

F

48"(121.92)

12"(30.48)

24 1/2"(62.27)

48"(121.92)

18 15/16"(48.06)

21 7/16"(54.52)

18 7/8"(47.98)

1 1/2"(3.77)

7 1/4"(18.48)

7 1/2"(19.05)

5 7/16"(13.81)

24 1/2"(62.23)

14 1/4"(36.19)

20 1/4"(51.38)

8 3/4"(22.23)

2 3/4"(6.99) 11 5/8"

(29.53) 22"

(55.88)

29"(73.66)

9"(22.86)

6 1/2"(16.51)

16 1/2"(41.91)

10 9/16"(26.83)

37 15/16"(96.34)

20 11/16"(52.59)

28 11/16"(72.90)

33 3/16"(84.30)Adjustable to36 3/16"(91.92)

Table cutout detail

D

CG

F

All connections are to be made byqualified personnel who will observe

all local and national codes.

Model PSM Drain Piping2” tank reservoir drain can be run separately or

be tied in with 2”-3” disposer drain.

NOTE: Dimensions in parenthesis are in centimeters

Design Tips

• Leave a 24” space between the ScrapMaster and dishmachine. Note: If dishmachine orientation is right of the ScrapMaster, the dish rack can sit on top of the disposer access cover (16”). In this case, only 4” is needed between the ScrapMaster and dishmachine.

• Do not direct connect ScrapMaster with inline trap or interceptor.

• Unit is multi-directional. No need to specify left or right hand version.

• Optional bracket available for remote start/stop only.

PLUMBINGn Corrosion Resistant Componentsn Automatic Water Blendern Solenoid Valvesn Unionsn Check Valvesn Incoming Water Valvesn Non-clogging Pump Designn Backflow Prevention Devicen Quick Opening Drain Valve

CONSTRUCTION MODELS AVAILABLEn Stainless Steel Componentsn Salvage Basin n Disposer Safety Covern Adjustable Legsn Control Panel

ELECTRICAL n Pre-wired NEMA 4 Paneln Patented Operator Sensorn Watertight Conduit /Fittingsn Separate Component Groundingn Thermally Protected Motorsn Totally Enclosed Motorsn Line Voltage Disconnectn Disposer Safety Switchn 24 Volt Safety Circuitry

Model Model Disposer300 SM 300 PSM 3 HP500 SM 500 PSM 5 HP

ACCESSORIESRemote Start-Stop ButtonRemote Mounting BracketCorrectional PackageStainless Steel Dejamming Prong

UTILITIES REQUIRED208, 230 or 460 Volt, 60 cycle, 3 phase electric service, 3⁄4” hot and cold water supply and reduce to 1⁄2” at connection. 2” or 3” waste line, 2” tank reservoir drain.

(Specifications subject to change without notice.)

SAMPLE SPECIFICATIONSUnit shall be a ScrapMaster (or Pot/Pan ScrapMaster)pre-flushing scrapping and food waste disposing system with recirculating water as manufactured by Salvajor.Model ____SM (or PSM), ____Volts, ___Hz, ___Phase.Furnished with a pre-wired HydroLogic control panel, sensor and stainless steel NEMA 4 watertight enclosure.

ScrapMaster® System Model SM & Model PSM Specifications

208V 230V 460V, 60 Cycle, 3 Phase Disposer 3-5 HP 208-230-460V Pump ¾ HP 208-230-460V Separator 1⁄6 HP 208-230-460V

VOLTAGES AVAILABLE (SPECIFY EXACT OPERATING VOLTAGE)

FULL LOAD AMPS TOTAL FULL LOAD AMPS THREE PHASE MODEL 208V 230V 460/480V Total HP 300-SM/PSM 12.7 11.7 5.9 4 500-SM/PSM 17.7 16.2 8.2 6

Disposernot included

in listing.

U.S. Pat. No. 7,815,134

4530 East 75th Terrace Kansas City, MO 64132-2081, USA816.363.1030 I Toll Free: 1.800.725.8256 I Service: 1.888.725.8256 I Fax: [email protected] I [email protected] I www.salvajor.com

Printed in USAForm No. SM (05-18)

Manufacturers of Commercial Food Waste Solutions - Since 1944