EURO 4 & 5 VM ENGINE Hydrostatic ILLUSTRATED PARTS CATALOGUE For Models Equipped with CANbus 2 Control
EURO 4 & 5 VM ENGINE
Hydrostatic
ILLUSTRATED PARTS CATALOGUEFor Models Equipped with CANbus 2 Control
Scarab VM Minor - CANbus 2 Illustrated Parts Catalogue Page i
ILLUSTRATED PARTS CATALOGUE
SCARAB MINOR
CANbus 2 VM ENGINED MODELS
When re-ordering this document please quote the following part number:Manual Z036776
Original Issue . . . . . . . . . . . . . . . July 2010Amendment 1 . . . . . . . . . . . . . .Aug 2010
This manual is published by the Technical Publications Department of Scarab Sweepers Limited and every effort is made to ensure that the information it contains is correct at the time of publication. Due to a policy of continuous development, however, the Company reserves the right to alter the specification and to supply when so altered without reference to illustrations and descriptions in this manual.
Scarab Sweepers LimitedPattenden Lane, Marden, Kent TN12 9QD, England
Telephone: 01622 831006 Fax: 01622 832417 International: +44 1622 831006 International +44 1622 832417e-mail: [email protected] Web site: www.scarab-sweepers.com
For Fast-Track Spares Fax Direct on 01622 831492
Publication Z036776 ORIGINAL DOCUMENT © Scarab Sweepers Limited 2010
M/c Serial No.
Page ii Illustrated Parts Catalogue Scarab VM Minor - CANbus 2
IMPORTANT NOTICE TO USERSIt is imperative that the correct model is FULLY identified when procuring replacement parts for your Scarab Sweeper. To avoid unnecessary confusion and delays caused by incorrectly ordered parts, please refer to the Vehicle Serial Number Plate and take note of the vehicle’s number.
NOTE:The Serial Number Plate is located at the rear of the driver’s cab, low down on the right hand side.
The example shown here is for guidance only.
This information MUST accompany EVERY parts order to ensure that the correct parts are supplied.
Scarab VM Minor - CANbus 2 Illustrated Parts Catalogue Page iii
AMENDMENT RECORDTo record an amendment to the manual, enter the number of the amendment leaflet and the date of incorporation on this card. It is advisable to annotate each amendment with the Amendment Instruction (AI) number to avoid confusion when successive amendments to the same section are issued.
Pour enregistrer une modification apportée au manuel, inscrire sur cette feuille le numéro de Ia fiche de modification et Ia date de I’insertion, II y a lieu de marquer chaque modification du numéro de Ia fiche pour éviter toute confusion lors de l’émission de modifications consécutives portant sur une même rubrique.
Un eine Abänderung in diesem Handbuch zu registriersen, soIl man die Nummer des Abänderungsblattes und Datum dessen Eingliederung auf dieser Karte eintragen. Es ist ratsam, dass jede Abänderung mit der Blattnimmer gekennzeichnet wird, so dass keine Verwechslung eintreten kann, wenn weitere Abänderungen des selbel TeiIs herausgegeben werden.
Para registrar una modificación del manual, anótese el número de Ia hoja de modificación y Ia fecha de incorporación en esta tarjeta. Es conveniente anotar las modificaciónes con el número de Ia hoja para evitar confusiones cuando se publiquen modificaciónes sucesivas de Ia misma sección.
Per annotare le modifiche a manuale, registrare il numero dell’ opuscolo modificato e Ia data d’ incororazione, su questa scheda. Annotare cascuna modifica con il numero dell’ opuscolo per evitare confusione, in caso di modifiche successive alla stessa sezione.
Amdt/AI No. Date Incorporated Actioned By Pages Affected By
Amendment036776/1 2/8/10 SCARAB TPD All Sections, All Pages
Section PageNumber Status Section Page
Number Status
PRELIM ALL AMDT.1
SECTION A ALL AMDT.1
SECTION B ALL AMDT.1
SECTION C ALL AMDT.1
SECTION D ALL AMDT.1
SECTION E ALL AMDT.1
SECTION F ALL AMDT.1
SECTION G ALL AMDT.1
SECTION H ALL AMDT.1
SECTION J ALL AMDT.1
SECTION K ALL AMDT.1
SECTION L ALL AMDT.1
Page iv Illustrated Parts Catalogue Scarab VM Minor - CANbus 2
LIST OF EFFECTIVE PAGES
Scarab VM Minor - CANbus 2 Illustrated Parts Catalogue Page v
HOW TO USE THIS ILLUSTRATED PARTS CATALOGUE
INTRODUCTIONThis Illustrated Parts Catalogue has been organised to facilitate ease of use when identifying and procuring replacement parts for the Scarab VM Minor Hydrostatic Sweeper (CANbus). The information content has been arranged in a logical manner by creating a number of separate sections, each dealing with a specific aspect or sub-system of the machine. Each section is a self-contained sub-division of the manual, complete with its own table of contents. Where relevant, cross-references from one section to another have been included to enable the user to quickly navigate to the information that gives the required level of detail; for example, the tansmission pump assembly is called up in Section B - Driveline because it is part of that system, but for details of internal components and replacement parts the reader is directed by appropriate cross-references, to Section J - Hydraulic System and Equipment.In support of the sections detailing the main sub-systems are two indexes (alphabetical and numerical) and these can be used to identify the correct location/items in the manual when either the part number or the parent assembly are unknown. These should be used as follows:
WHEN THE PART NUMBER IS KNOWNWhen a component’s or an assembly’s part number is known but the parent assembly is not known, refer to the Index Card at the front of this manual to locate the Numerical Index. Turn to the index and find the part number in the index listing. Note the section and page number(s) and then turn to the appropriate section/page(s). Scan the parts list on the relevant page(s) to locate the part number in question noting its item reference number (this is the number in the left hand column) and its quantity as required. Next, refer to the accompanying illustration and identify the item reference number and the component to which it refers.
WHEN THE PART NUMBER IS NOT KNOWNTwo methods are available for locating and identifying a component or an assembly when its part number is not known. Firstly, refer to the Index Card at the front of this manual, then, if the item’s description is known, refer to the Alphabetical Index to locate the appropriate section/pages. Alternatively, if the machine sub-system to which the item relates is known, refer to the Index Card to locate the appropriate section. Once the correct section is identified, use its Table of Contents to identify the page(s) covering the required information. Turn to the correct page(s) and then refer to the illustration to identify the component or assembly, noting its item reference number. Next, refer to the associated parts list opposite and locate the item reference number identified by the illustration, noting the item’s part number, quantity and description as required.
USING THE PARTS LISTSThe breakdown structure within each parts list reflects the inter-relationship of the various components in what is, loosely, an assembly/disassembly order, however, it must be stressed that this is not necessarily a true reflection of factory assembly/disassembly procedures, but is used to show logical groups of components. The order of information (L to R) is: Item/Part No./Quantity/Description.
The first item on a parts list (the main assembly in question) is always shown in bold uppercase, thus:DESCRIPTION OF MAIN ASSY
The succeeding parts generally fall into two categories, namely attaching parts i.e. bolts, screws, nuts, washers etc. or breakdown parts i.e. sub assemblies and/or piece parts.Attaching parts always immediately follow the assembly, sub-assembly or piece part to which they relate and are indented, for example:
065432 1 DESCRIPTION OF MAIN ASSY012345 4 . Screw, hex hd, M25 x 100 mm long012346 4 . Nut, hex, Nyloc, M12
The breakdown parts are then listed as described earlier in this paragraph with each successive level being indented from its own parent level (as in the foregoing example, attaching parts are listed first), as follows:
Page vi Illustrated Parts Catalogue Scarab VM Minor - CANbus 2
HOW TO USE THIS ILLUSTRATED PARTS CATALOGUE
USING THE PARTS LISTS (Continued)065432 1 DESCRIPTION OF MAIN ASSY012345 4 . Screw, hex hd, M25 x 100 mm long012346 4 . Nut, hex, Nyloc, M12
1 064321 1 . Sub-Assy 1 of Main Assy012356 2 . . Screw, skt hd, M6 x 30 mm long012344 2 . . Washer, plain, 6 mm012355 2 . . Nut, hex, Nyloc, M6
2 045678 1 . . Sub-Sub-Assy 1 of Sub-Assy 13 032145 1 . . . Piece part 1 of Sub-Sub-Assy 14 032146 1 . . . Piece part 2 of Sub-Sub-Assy 15 032187 1 . . . Piece part 3 of Sub-Sub-Assy 16 045678 1 . . Sub-Sub-Assy 2 of Sub-Assy 17 032142 1 . . . Piece part 1 of Sub-Sub-Assy 28 032149 1 . . . Piece part 2 of Sub-Sub-Assy 29 064321 1 . Sub-Assy 2 of Main Assy
012356 2 . . Screw, skt hd, M6 x 30 mm long012344 2 . . Washer, plain, 6 mm012355 2 . . Nut, hex, Nyloc, M6 etc.
As the parts list develops it can be seen how the individual items comprising the Main Assembly are related and how this relationship is shown by indenting. In some cases these might be actual factory sub-assemblies but they could equally be no more than logical groupings of items that are related to one another, such as a gearbox shaft, the gears that fit on that shaft and the bearings that the shaft runs in.
ITEM REFERENCE NUMBERSItem reference numbers are used to cross-refer items from the parts lists to their associated illustrations and vice-versa. Normally, all items other than attaching parts are given a number, however, there are two exceptions:Attaching parts that are not standard items e.g. a special screw, are given an item reference number.Items that are not illustrated for a particular reason, e.g. where one half of a handed assembly is already illustrated, or where illustration of that item is superfluous, are listed as not illustrated (NI).
Scarab VM Minor - CANbus 2 Illustrated Parts Catalogue Page vii
SAFETY FIRST
IN THE INTERESTS OF YOUR HEALTH AND SAFETY, IT IS IMPORTANT THATTHE FOLLOWING POINTS ARE OBSERVED AT ALL TIMES:
• BEFORE DRIVING THE MACHINE CHECK THAT THE CAB SAFETY LOCK IS PROPERLY ENGAGED IN THE LOCKED POSITION.
• DO NOT DRIVE THE VEHICLE WITH THE HOPPER IN THE RAISED POSITION, EVEN IF THE HOPPER IS EMPTY.
• BEFORE DRIVING THE VEHICLE ENSURE THAT ALL RELEVANT VEHICLE CHECKS HAVE BEEN CARRIED OUT, THAT ALL EQUIPMENT IS STOWED AND THAT THE BRUSHES HAVE BEEN RAISED.
• ALWAYS USE THE HOPPER PROP TO SUPPORT A RAISED HOPPER AND NEVER WORK UNDER A RAISED HOPPER UNLESS THE PROP IS IN POSITION.
• BEFORE WORKING ON THE MACHINE: POSITION THE VEHICLE ON FIRM, LEVEL GROUND, APPLY THE HANDBRAKE, STOP THE ENGINE, REMOVE THE IGNITION KEY.
• BEFORE OPERATING EITHER THE HOPPER-TIP CONTROLS OR REAR DOOR, ENSURE THAT THERE IS SUFFICIENT CLEARANCE AND THAT IT IS SAFE TO DO SO.
• EXERCISE EXTREME CARE WHEN DISCHARGING THE HOPPER. FOLLOW THE INSTRUCTIONS DETAILED IN THIS MANUAL.
• BEFORE STARTING THE ENGINE ENSURE THAT ALL CONTROLS ARE SWITCHED OFF AND THAT THE VEHICLE IS IN NEUTRAL.
• DO NOT OVERLOAD THE HOPPER.• HIGH-PRESSURE WATER CAN BE HAZARDOUS, ALWAYS WEAR SUITABLE EYE PROTECTION
WHEN OPERATING THE HIGH-PRESSURE WATER PUMP AND WHEN USING THE LANCE. DO NOT DIRECT THE WATER JET AT OTHER PERSONS. BEWARE OF ELECTRICAL INSTALLATIONS ON PUBLIC BUILDINGS & LAMP POSTS Etc. AND ALWAYS EXERCISE EXTREME CAUTION.
REMEMBER, FAILURE TO COMPLY CAN RESULT IN SERIOUS INJURY.IF IN DOUBT, ASK!
VEHICLE ‘BEFORE USE’ CHECKS(All checks are visual unless otherwise stated)
1. CHECK THAT THE HYDRAULIC OIL LEVEL IS CORRECT.2. CHECK FOR HYDRAULIC OIL LEAKS.3. CHECK BRUSHES AND SKIRTS FOR WEAR AND REMOVE ANY ITEMS SUCH AS STRING
WHICH MIGHT HAVE BECOME ENTANGLED.4. CHECK THAT ALL EQUIPMENT IS CORRECTLY STOWED AND THAT ALL BRUSHES ARE IN
THE RAISED POSITION.5. CHECK WATER SPRAY JETS FOR BLOCKAGES.6. CHECK GENERAL VEHICLE CONDITION FOR SAFETY.7. CHECK EXTERIOR LIGHTING FOR CORRECT OPERATION AND GENERAL CLEANLINESS.8. CHECK THE FOLLOWING FLUID LEVELS AND TOP UP AS REQUIRED:
(a) ENGINE OIL (b) ENGINE COOLANT (c) WINDSCREEN WASH (d) BRAKE FLUID (e) FUEL
9. CHECK TYRES FOR DAMAGE AND FOR CORRECT INFLATION PRESSURES.
Page viii Illustrated Parts Catalogue Scarab VM Minor - CANbus 2
SCARAB MINOR FL - MAIN FEATURES
HYDRAULICS COVER
WATER TANK
REAR-MOUNTED
TILTING CAB
FRONT BRUSH
OIL TANKMAIN HYDRAULIC
CAB SAFETY LATCH
SIDE BRUSH
SUCTION NOZZLE
H-P HOSE REEL
HOPPER CANOPY AIR INTAKESILENCER & SHIELD
H-P WATER
STRAINER - H-P PUMP
FUEL TANKAIR CLEANER
WIDESWEEP
L-P WATER PUMP
SUCTION FAN
VALVE BLOCK
PUMP
SIDE-LOADINGDOOR
WANDERHOSE
MANUAL GREASE POINT LOCATIONSCOMPONENT / ASSEMBLY No. OF GREASE POINTS
LEFT HAND SIDE BRUSH ASSEMBLY 3RIGHT HAND SIDE BRUSH ASSEMBLY 3SWING-OUT FRONT BRUSH ASSEMBLY 3NON SWING-OUT FRONT BRUSH ASSEMBLY 3LEFT HAND DOOR 2RIGHT HAND DOOR 2REAR DOOR 2WIDE SWEEP ASSEMBLY 1PROPSHAFT 3STREETWASH SPRAY BAR OPTION 3KING PINS (PER SIDE) 2LEFT HAND AUTOMATIC BLANKING ASSEMBLY* 1RIGHT HAND AUTO BLANKING ASSEMBLY* 1* Dual Sweep Machines Only
RECOMMENDED LUBRICANTS & FLUIDS
COMPONENT SAE SPECIFICATION SCARABPART No.
FILLING CAPACITY
COOLING SYSTEM Water/Anti-freeze to suit conditions 005000 (5 litre) 10 litresPOWER STEERING see Hydraulic Tank N/AHYDRAULIC TANK HLP32 Hydraulic Oil 005005 (5 litre) 15 LitresGREASE POINTS Lithium Grease N.L.G.I. No. 2 005007 (400 g) Refer to the Maint’nce
ScheduleWHEEL BEARINGS Lithium Grease N.L.G.I. No. 2 005007 (400 g)REAR AXLE SAE 90 EP Hypoid Gear Oil 1.7 litresBRAKE SYSTEM Brake Fluid to DOT 4 005004 (1 litre) 0.7 litresH-P WATER PUMP Motor Oil SAE 20W/30 or 20W/40 005001 (5 litre) 0.55 litres
Scarab VM Minor - CANbus 2 Illustrated Parts Catalogue Page ix
If you have any concerns regarding the foregoing information, please contact the Service Department at Scarab Sweepers Limited, for further advice.
MANUAL GREASE POINT LOCATIONS
SIDE BRUSH ASSEMBLY FRONT BRUSH ASSEMBLY
WIDE SWEEP ASSEMBLY
STREETWASH CONVERSION SPRAY-BAR
SWIVEL BRACKET
MOUNTING PLATE
PROP SHAFT
HOPPER AUTO-BLANKING MECHANISM
RH side of hopper shownas viewed from cab
KING PINS
DOOR HINGES
REAR DOOR
Page x Illustrated Parts Catalogue Scarab VM Minor - CANbus 2
Scarab VM Minor - CANbus 2 Illustrated Parts Catalogue Page xi
WARRANTY STATEMENT1. Scarab Sweepers Limited (hereinafter referred to as the Company) warrants that (subject to the other
provisions of the published Terms and Conditions of Sale - available upon request) upon delivery and for a period of 12 months from the date of actual delivery, or 2,000 running hours from the date of actual delivery whichever is sooner, the Goods correspond with their specification at the time of delivery, and will be free from defects in materials and workmanship.
2. The Company does not warrant the condition or quality of any used Goods supplied to the Customer, or other truck manufacturers' chassis cab content or to the engine fitted in the Scarab Minor Sweeper or to any other component not manufactured by the Company and any such warranty claims must be submitted to the manufacturer of that component, or their locally appointed agent.
3. The Company shall not be liable for a breach of any of the warranties in condition 1 unless the Customer gives written notice of the defect to the Company, and (if the defect is as a result of damage in transit) to the carrier, within 7 days of the time when the Customer discovers or ought to have discovered the defect.
4. The Company shall not be liable for a breach of any of the warranties in condition 1 if the Customer makes any further use of such Goods after giving such notice, the defect arises because the Customer failed to follow the Company's oral or written instructions as to the storage, installation, commissioning, use or maintenance of the Goods or (if there are none) good trade practice, or the Customer alters or repairs such Goods without the written consent of the Company, or uses non genuine parts to effect a repair.
5. The following consumable items listed are excluded from the Company warranty:all fuel oils,antifreeze,all brush link pivots and bushes,wander hoses, suction nozzles,body inlet ducts, wearing plates,high-pressure water pump piston seals and valves,door seals,inlet seals,batteries,tyres,all brushes,lift cables,rubber skirts,suction nozzle wheels,flap trunking,deflectors,screens flaps or blanking plates,water pump diaphragm valves and water jets,all filter strainers and elements,windows,glass mirrors,light bulbs,fuses,brake lining pads,auxiliary drive belts and any other part normally regarded as consumable.
6. Any parts replaced under the terms of this warranty will be covered by the unexpired portion of this warranty.7. Subject to conditions 3 and 4, if any of the Goods do not conform with any of the warranties in condition 1
the Company shall at its option repair or replace such Goods (or the defective part) or refund the price of such Goods at the pro rata Contract rate provided that, if the Company so requests, the Customer shall, at the Customer's expense, remove the defective Goods or part of such Goods and return the Goods or the part of such Goods which is defective to the Company. Parts replaced under warranty will be delivered by the Company FOB port of exportation.
8. If the Company complies with the terms contained in this statement it shall have no further liability for a breach of any of the warranties in condition 1 in respect of such Goods.
9. No representative or agent of Scarab Sweepers Limited has the authority to add or to vary these Warranty Conditions except with the Company's official confirmation in writing from Scarab Sweepers Limited, head office in Marden Kent, England. 1.Scarab Sweepers Limited (Hereinafter referred to as The Company) subject to Conditions 2 - 6 below warrants that any new Goods supplied to the Customer under the Contract [will correspond with their specification at the time of delivery and] will be free from defects in materials and workmanship for a period of [twelve] months from the date of actual delivery or [2,000] running hours from the date of actual delivery whichever is the sooner The Company does not warrant the condition or quality of any used Goods supplied to the Customer.For further information, please refer to the Company’s Terms and Conditions of Sale. In the event of conflict between this Warranty Statement and the Company’s Terms and Conditions of Sale the latter will prevail.
Page xii Illustrated Parts Catalogue Scarab VM Minor - CANbus 2
THIS PAGE INTENTIONALLY LEFT BLANK
Scarab VM Minor - CANbus 2 Illustrated Parts Catalogue Page xiii
ENGINE & FUEL SYSTEM
DRIVELINE
BRAKING SYSTEM
CHASSIS RELATED PARTS
CAB
HOPPER
WATER
HYDRAULICS
ELECTRICAL
SWEEPING & SUCTION EQUIPMENT
GLOSSARY
STREETWASH
LABELS AND DECALS
Page xiv Illustrated Parts Catalogue Scarab VM Minor - CANbus 2
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776/ Issue: Amdt.1 - 11/8/10
SECTION AVM ENGINE SYSTEM
TABLE OF CONTENTS
Assembly/Description Page
Engine general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Exhaust - cooling - air - general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5Air filter components - EURO 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Exhaust arrangement - EURO 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Fuel system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
NOTE:Unless stated all parts are common for EURO 4 and 5 models
A Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Engine & Fuel System Manual Number Z036776/ Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
VM ENGINE - GENERAL ARRANGEMENT1 032270 1 Engine mount, RH
NI 037141 1 Engine mount, RH - EURO 5NI 033104 1 Engine mount, LHNI 037140 1 Engine mount, LH - EURO 52 032883 1 . Coupling, plastic3 032884 1 . . Hub4 025031 1 . Bellhousing5 033519 1 . Starter motor6 033520 1 . Alternator7 033521 1 . . Drive belt, alternator8 034060 1 . . . Tensioner, alternator belt9 034061 1 . . . . Idler pulley, alternator belt tensioner
10 033452 1 . Oil filter - EURO 4 10 037929 1 . Oil filter - EURO 5 NI 026281 1 . . O-ring, oil filter11 034062 1 . Dip stick & tube12 034063 1 . . Dip stick onlyNI 033346 1 . Cover, timing beltNI 033544 1 . . Bracket, cover, timing beltNI 032869 1 . Cover, rocker box, plasticNI 034057 1 . Gasket, rocker boxNI 034058 1 . Plug, sump drainNI 034059 1 . . Washer, sump plug13 032564 1 . Gear pump, steering14 033538 1 . Exhaust gasket15 036628 1 . Turbo unit16 026307 1 . Filler cap & O-ring (Oil)17 034042 4 . Fuel injectors
ENGINE SENSORS18 034043 1 Boost-pressure & temperature sensor19 034045 1 Coolant temperature sensor20 034046 1 Crankshaft speed sensor21 034048 1 Rail pressure sensor22 034050 1 Oil-pressure & temperature sensor23 034051 1 Camshaft speed sensor24 034053 1 Water in fuel sensor - EURO 4 24 037935 1 Water in fuel sensor - EURO 5 25 034054 1 Fuel temperature sensorNI 034049 1 Fuel injector pump sensor
NOTE:Unless stated all parts are common for EURO 4 and 5 models
The following are recommended service periods.First 50 Hours - for Service Kit order Part Number 033788300 Hours - for Service Kit order Part Number 033789900 Hours - for Service Kit order Part Number 0337901800 Hours - for Service Kit order Part Number 033791
The opposite photos show the VM engine removed from the vehicle. For information on parts not listed here, please contact our parts department quoting the machine serial number.The ECU must be matched to the correct serial number prior to shipping from the manufacturer.When procuring a replacement engine ECU, it is important to quote your engine serial number.
VM ENGINE - GENERAL ARRANGEMENT
5
67
10
11,12
8
9
FuelFilter
1
2,3
1617
18 19
20
24
25
21
22 23
High-Pressure Pump
4 14
15
13
ILLUSTRATED PARTS CATALOGUE Section ASCARAB VM MINOR - CANbus Page 2
Manual NumberZ036776/ Issue: Amdt.1 - 11/8/10 Engine & Fuel System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
A
A Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Engine & Fuel System Manual Number Z036776/ Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
EXHAUST, COOLING AND INTERCOOLER - GENERAL ARRANGEMENT
EURO 4
1 020873 1 Pre cleaner - stack cap2 034924 1 . Air intake extension pipe
011011 2 . . Setscrew, hex head, M8 x 25 mm long011073 4 . . Washer, M8, plain011073 2 . . Nut, M8 Nyloc
3 012931 4 . Clamp, worm drive, 70 - 90 mm4 014886 1 . Flexible hose5 005112 5 . . Clamp, worm drive, 60 - 80 mm6 025540 1 . Connector - air cleaner7 025279 1 . Air cleaner assembly
011011 2 . . Setscrew, hex head, M8 x 25 mm long011092 4 . . Washer, M8, plain011073 2 . . Nut, M8 Nyloc
8 025280 1 . . Filter, main element9 025281 1 . . Filter, safety element
10 025450 1 . . Vacuator, air cleaner11 025550 1 . . Elbow, rubber, reducing, 89 to 76 mm12 012931 1 . . . Clamp, worm drive, 70 - 90 mm13 003003 2 . . . Clamp, worm drive, 13 - 20 mm14 032951 1 . . Pipe, rubber, moulded, air filter to turbo15 034130 1 Radiator assembly........................Page J1116 020517 1 . Expansion bottle17 020518 1 . Expansion bottle cap
011087 2 . . Setscrew, hex head, M6 x 25 mm long011091 2 . . Washer, M6, plain011091 2 . . Washer, M6, spring
18 001035 1 . Pipe, rubber, 8 mm bore19 033361 1 . Pipe, steel, radiator to thermostat20 034225 2 . Pipe, rubber, radiator to items, 16-18 mm21 003007 7 . . Clamp, worm drive, 35 - 50 mm22 033362 1 . Pipe, steel, cooler to water pump23 001070 1 . Hose, rubber, ” BSP x 4350 mm long, straight end + 90°24 033832 1 . Pipe, rubber, moulded, intercooler to item 2825 012927 3 . . Clamp, worm drive, 40 - 55 mm26 028778 1 . . Clamp, worm drive, hi-torque, 40 - 70 mm27 032877 1 . Pipe, steel, intercooler LH
011067 2 . . Setscrew, hex head, M6 x 25 mm long011071 2 . . Nut, M6 Nyloc
28 032953 1 . Pipe, steel, intercooler RHNI 030927 1 . Bracket, pipe support
005055 1 . . P-clip, 50 mm011067 1 . . Setscrew, hex head, M6 x 25 mm long011087 1 . . Setscrew, hex head, M6 x 30 mm long011090 2 . . Washer, M6, plain011071 2 . . Nut, M6 Nyloc
29 033831 1 . Pipe, rubber, moulded, intercooler to item 2730 033217 1 . Elbow, rubber, moulded, Intercooler lower pipe31 032952 1 . Pipe, rubber, moulded, intercooler to plenum32 032954 1 . Pipe, rubber, moulded, cooler to thermostat33 032950 1 . Pipe, rubber, moulded, cooler to water pump34 012928 1 . . Clamp, worm drive, 45 - 60 mm35 013409 2 . Anti-vibration mount (Upper)36 036768 2 . Anti-vibration mount (Lower, blue ring)
011094 8 . . Washer, M10, plain011075 8 . . Nut, hex, M10 Nyloc
Continued...
1
2,3
4,5
18
6,7,8,9,10
15
11,12,13
14,13,5
20,21
20,21
19
22
2324,25,26
2728
29,26
30
31,5
16,17
32,2133,34,21
EXHAUST, COOLER& INTERCOOLER GENERAL ARRANGEMENT
35
36
ILLUSTRATED PARTS CATALOGUE Section ASCARAB VM MINOR - CANbus Page 4
Manual NumberZ036776/ Issue: Amdt.1 - 11/8/10 Engine & Fuel System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
A
A Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Engine & Fuel System Manual Number Z036776/ Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
. Item Part Number Quantity Description
COOLER & EXHAUST GANTRY ARRANGEMENT
}EURO 4 37 034365 1 DPF sensor pipe (feed)38 034366 1 DPF sensor pipe (return)NI 020902 2 . Adaptor, 6 mm x ’’ BSP, M/M39 010957 As req . Pipe, rubber, 6 mm bore40 002007 As req . Pipe, rubber, 8 mm bore41 034079 1 . DPF sensor42 032873 1 . Bracket header tank
011011 2 . . Setscrew, hex head, M8 x 25 mm long011093 2 . . Washer, M8, spring
43 032956 1 . Elbow, rubber 16/1944 010517 2 . . Clamp, worm drive, 18 - 25 mm45 010909 1 . Tee, ” BSP, galvanised, F/F/F46 010922 1 . . Hose tail, ” BSP x ” tube47 010516 4 . . Clamp, worm drive, 11 - 16 mm48 011171 1 . Elbow, swivel, ” BSP, M/F49 001014 As req . Pipe, rubber, 10 mm bore50 033372 1 Throttle valve actuator circuit51 034055 2 . Vacuum modulator52 006041 1 . Tee, ’’ BSP, F/F/F53 006042 2 . Hose tail ’’ BSP x 4 mm tube54 006043 2 . Hose tail ’’ BSP x 8 mm tube55 006047 As req . Pipe, rubber, 4 mm bore
}EURO 4
56 036171 * 1 Exhaust silencer DPFNI 036173 1 . Clamp57 032878 1 . Upper silencer bracket58 032879 1 . Lower silencer bracket59 033354 2 . Silencer clamp
011073 4 . . Nut, hex, M8 Nyloc60 033204 2 . Exhaust clamp61 032870 1 . Exhaust pipe62 032874 1 . Exhaust stack63 036685 1 DPF sensor cover
011087 1 . Setscrew, hex head, M6 x 25 mm long011071 1 . Nut, hex, M6 Nyloc011090 1 . Washer, M6, plain000028 1 . Screw, slotted round head, 2BA x ” long
} EURO 4
64 034788 1 Bracket, cab extension panel RH rear011011 4 . Setscrew, hex head, M8 x 25 mm long011073 4 . Washer, M8, plain011073 2 . Nut, hex, M8 Nyloc
NI 034789 1 Bracket, cab extension panel RH front011011 4 . Setscrew, hex head, M8 x 25 mm long011073 4 . Washer, M8, plain011073 2 . Nut, hex, M8 Nyloc
NOTE:Unless stated all parts are common for EURO 4 and 5 models
* These items are also available as Service Exchange units
38
37
51
5062
59
56
57, 60
58, 60
59
61
51
52,53,54
55 60
3159
EXHAUST, COOLER & INTERCOOLER GENERAL ARRANGEMENT
41
40
39 63
THROTTLE VALVE ACTUATOR CIRCUIT
64
To Alternator
42
43,4445,46,4748
49
ILLUSTRATED PARTS CATALOGUE Section ASCARAB VM MINOR - CANbus Page 6
Manual NumberZ036776/ Issue: Amdt.1 - 11/8/10 Engine & Fuel System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
A
A Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Engine & Fuel System Manual Number Z036776/ Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
AIR FILTER COMPONENTS - EURO 5 1 037933 1 Air cleaner, complete assembly
011010 4 . Setscrew, hex head, M8 x 20 mm long011092 4 . Washer, M8, plain
2 037931 1 . Pre - air filter3 037932 1 . Main filter4 037934 1 . Air filter indicator5 037146 1 . Hose, rubber, reinforced, air filter evac, upper6 012927 4 . Clamp, worm drive, 40 -55 mm7 037147 1 . Pipe, stainless steel, air filter evac, centre8 037148 1 . Hose, rubber, reinforced, air filter evac, lower9 036691 1 . Hose, rubber, reinforced, engine air intake, upper
10 003003 4 . Clamp, worm drive, 90 - 100 mm11 036838 1 . Pipe, stainless steel, engine air intake, centre12 037163 2 . Support clamp, centre pipe
}Per clamp
011067 2 . . Setscrew, hex head, M6 x 20 mm long011090 4 . . Washer, M6, plain011071 2 . . Nut, hex, M6 nyloc011011 1 . . Setscrew, hex head, M8 x 25 mm long011092 2 . . Washer, M8, plain011073 1 . . Nut, hex, M8 nyloc
13 036690 1 . Hose, rubber, reinforced, engine air intake, lower14 037934 1 . Inicator, air filter15 025949 1 . . Hose tail, 10mm x 1 pitch x 8 mm tube16 002007 As req . . Hose, rubber, 8 mm bore17 010964 2 . . . O-clip, 9/16
Item Part Number Quantity Description
EXHAUST ARRANGEMENT - EURO 51 037937 1 Exhaust silencer
011031 4 . Setscrew, hex head, M10 x 25 mm long2 037432 1 . Exhaust, stack pipe3 037686 1 . Exhaust, rain cap4 037166 1 . Exhaust, guard5 036689 1 . Exhaust pipe, manifold to silencer6 033354 2 . Silencer clamp
011073 2 . . Nut, hex, M8 Nyloc7 037701 1 . Pipe, steel, DPF senser, upper
NI 037167 2 . . Adaptor, elbow, DPF8 037701 1 . Pipe, steel, DPF sensor, lower
1,2,34
VEIWED FROM REAR OF GANTRY
8,67
5,6
9,10
11
13,10
12
AIR FILTER COMPENENTS - EURO 5
14
15,16
17
1
2
3
4
5
7
8
6
6
EXHAUST ARRANGEMENT - EURO 5
ILLUSTRATED PARTS CATALOGUE Section ASCARAB VM MINOR - CANbus Page 8
Manual NumberZ036776/ Issue: Amdt.1 - 11/8/10 Engine & Fuel System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
A
A Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Engine & Fuel System Manual Number Z036776/ Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
FUEL SYSTEM1 018204 1 Fuel tank assembly (comprises items 2 (or 2a) to 10 + 14)2 032654 1 . Tank, fuel (single sweep machines)
2a 036236 1 . Tank, fuel, anti-syphon (optional on single sweep machines)3 032652 1 . Sender, fuel level4 032653 1 . . Ring, locking5 032805 1 . . Ring, sealing
NI 022237 1 . . Harness, electrical, fuel sender unit6 013953 2 . Bracket, mounting, fuel tank
011013 8 . . Setscrew, hex head, M8 x 35 mm long034280 8 . . Spacer011073 8 . . Nut, hex, M8, Nyloc
7 013954 2 . Strap, fuel tank000059 2 . . Screw, socket cap head, M8 x 5 0mm long011073 2 . . Nut, hex, M8, Nyloc000080 2 . . Nut, hex, ” UNF, Nyloc
8 010945 1 . Drain plug, fuel tank9 011153 1 . . Seal, Dowty ” BSP
10 033330 1 . Cap assembly, fuel tankNI 025892 1 . Cap, locking, fuel tank (optional)11 034145 As Req . Hose, fuel, 10 mm bore
010964 2 . . Clip, hose, ”12 033453 1 . Filter, fuel
011032 2 . . Setscrew, hex head, M8 x 30 mm long011075 2 . . Nut, hex, M8, Nyloc032872 1 Bracket011067 2 . . Setscrew, hex, M6 x 20 mm long011071 2 . . Nut, hex, M6
13 N/A 1 Injector pump arrangement14 033359 1 . Earth lead15 010922 2 . Hose connector ” BSP x ”16 011152 2 . . Seal, Dowty ” BSP17 032655 1 . Tank, fuel (rear mounted dual sweep machines)
011031 4 . . Setscrew, hex head, M10 x 25mm long011094 4 . . Washer, M10, plain011075 4 . . Nut, hex M10 Nyloc
FUEL SYSTEM ARRANGEMENT
2
3
4
5
6
rubber Cushion Strip(part of item 6)
78
9
10 Chassis Side Rail
1
17
Layout of main components
RH Sweep illustrated + Dual Sweep
1213
15,16
11
11
11
11
Reference Only
14
FILLER DETAIL 2a
ILLUSTRATED PARTS CATALOGUE Section ASCARAB VM MINOR - CANbus Page 10
Manual NumberZ036776/ Issue: Amdt.1 - 11/8/10 Engine & Fuel System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
A
A Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR - CANbus
Engine & Fuel System Manual Number Z036776/ Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
SECTION BDRIVELINE
TABLE OF CONTENTS
Assembly/Description Page
Drive line general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Drive motor assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Propshaft general assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Rear axle assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
NOTE:Unless stated all parts are common for EURO 4 and 5 models
B Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Driveline Manual Number Z036776/ Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
DRIVELINE GENERAL ARRANGEMENT1 024672SE 1 DRIVE MOTOR 51V110............................................................Page B32 014694 1 PROPSHAFT..............................................................................Page B53 025573 1 REAR AXLE ASSEMBLY.............................................................Page B74 021038 1 OIL FILTER ...............................................................................Page J13
NI 024516 1 TRANSMISSION PUMP ASSEMBLY ...........................................Page J5
1
2
3
UNDERSIDE OF VEHICLE - SHOWING DRIVELINE1. DRIVE MOTOR - 2. PROPSHAFT - 3. REAR AXLE
DRIVE-LINE - GENERAL LAYOUT
4
ILLUSTRATED PARTS CATALOGUE Section BSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Amdt. 1 - 11/8/10 Driveline
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
B
B Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Driveline Manual Number Z036776/ Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
DRIVE MOTOR ASSEMBLY1 024672SE 1 Drive motor, 51V110-T
011137 4 . Setscrew, hex head, M18 x 50 mm long 011139 4 . Nut, hex, M18, Nyloc
2 011265 2 . Adaptor, 1 ” UNF x ” BSP, M/M3 011234 1 . Elbow, hosetail, ” BSP x ” hose4 010517 2 . . Clamp, worm drive, 18 - 25 mm5 002073 1 . Test point, ” UNF6 002001 4 . Flange, split, 1”
000036 7 . . Screw, socket cap head, ” UNC x 1 ” long 000025 1 . . Bolt, hex head, ” UNC x 1 ” long000039 8 . . Washer, ”, spring
7 031320 1 . Hose, rubber, transmission, 635 mm long, REVERSE8 031321 1 . Hose, rubber, transmission, 660 mm long, FORWARD9 026179 1 . Pulse Pick Up (PPU)
10 025410 1 . . Connector lead (PPU)11 025040 1 . Adaptor, restrictor No 12, ” UNF x ” BSP x ” orifice12 011171 1 . Elbow, Swivel, ” BSP, F/F13 002014 1 . . Adaptor, ” BSP, M/F 14 030529 1 . . Pressure Switch, hydrostatic braking15 026033 1 . Plug, solenoid16 027238 1 . Solenoid & coil, 12 Volt
NA 026032 1 . . Coil, 12 Volt17 021329 1 . .Motor support
011031 4 . . Setscrew, hex head, M10 x 25 mm long 011075 4 . . Nut, hex, M10, Nyloc
18 013955 2 . Strut 011031 4 . . Setscrew, hex head, M10 x 25 mm long 011075 4 . . Nut, hex, M10, Nyloc
19 014747 1 . .Coupling, (to prop shaft flange)000025 1 . . Setscrew, hex head, ” UNC x 1 ” long013439 1 . . Washer, special
NI 013518 1 . O-RingNI 013523 1 . O-RingNI 020577 1 . V-Ring, motorNI 036458 1 . SealNI 014693 1 . . Buffer, rubber *
000072 2 . . Setscrew, hex head, M10 x 45 mm long011074 2 . . Washer, M10, plain011075 2 . . Nut, hex, M10, Nyloc
* NOTE: The rubber buffer is fitted to the right hand side of the motor support. Right hand and dual sweep machines only.
DRIVE MOTOR ASSEMBLY
1
2,3,4
2,3,4
6
7
8
9
111314
16
5
12
10
15
17
18
19
ILLUSTRATED PARTS CATALOGUE Section BSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Amdt. 1 - 11/8/10 Driveline
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
B
B Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Driveline Manual Number Z036776/ Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
PROPSHAFT GENERAL ARRANGEMENT1 014694 1 Propshaft2 020109 2 . Universal joint
NI 024129 1 . . Grease nipple011026 4 . . Setscrew, hex head, ” UNF x 1” (Prop)011405 4 . . Nut, hex, ” UNF, Nyloc (Prop)
3 014747 1 . Coupling, drive motor000078 4 . . Bolt, hex head, ” UNF x 1 ” (Prop)011405 4 . . Nut, hex, ” UNF, Nyloc (Prop)
1
3
PROPSHAFT GENERAL ARRANGEMENT
2
UNDERSIDE OF VEHICLE
ILLUSTRATED PARTS CATALOGUE Section BSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Amdt. 1 - 11/8/10 Driveline
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
B
B Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Driveline Manual Number Z036776/ Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
REAR AXLE ASSEMBLYNI 025573 1 Axle, complete1 020210 1 Axle carrier and tube2 020162 1 . Drive flange3 020164 1 . . Pinion oil seal4 020165 1 . . Pinion oil thrower5 020166 1 . . Pinion tail bearing6 020167 1 . . Collapsible spacer *7 020169 1 . . . Pinion washer *8 020168 1 . . . Pinion locknut9 020206 1 . Rear cover
10 020214 2 . Half shaft11 020215 2 . . Hub oil thrower12 020216 2 . . Hub seal13 020218 2 . . Hub bearing, inner14 020220 2 . . Hub bearing, outer15 020221 2 . . Locknut, hub inner 16 020222 2 . . . Lock washer17 020223 2 . . . Locknut, hub outer18 020224 2 . . . Gasket19 020226 16 . . . . Bolt, special, half shaft20 020180 1 . . . Hub & stud assembly, LH (includes items marked **)21 020219 2 . . . . Hub **22 020213 6 . . . . Wheel stud, LH**NI 020181 1 . . . Hub & stud assembly, RH (includes items marked **)
020219 2 . . . . Hub **020217 6 . . . . Wheel stud, RH**
23 020211 1 . Axle Breather24 020212 1 . Drain plug, magnetic
2
7
8
3
4
5
6
24
23
1
10
11
12
13
22
21
15
16
17
18
19
14
REAR AXLE ASSEMBLY
20
}9
ILLUSTRATED PARTS CATALOGUE Section BSCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Amdt. 1 - 11/8/10 Driveline
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
B
B Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Driveline Manual Number Z036776/ Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
SECTION CCHASSIS RELATED PARTS
Table of Contents
Assembly/Description Page
Chassis general arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Gantry general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Gantry general arrangement - EURO 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Front mud flap assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Rear mud guard assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Front suspension assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Rear suspension assembly & associated parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Front axle & steering arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Steering arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Teal hand wash basin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
NOTE:Unless stated all parts are common for EURO 4 and 5 models
C Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
CHASSIS GENERAL ARRANGEMENT1 013498 1 Bumper, front
011031 6 . Setscrew, hex head, M10 x 25 mm long011075 6 . Nut, hex, M10 Nyloc013662 4 . . Bush
2 027734 2 Cab pivot bracket3 027731 2 . Bush (brass bush insert 027732)
011011 8 . . Setscrew, hex head, M8 x 25 mm long011073 8 . . Nut, hex, M8 Nyloc
4 013426 1 Footplate5 022320 1 Step, LH
NI 022321 1 Step, RH011010 4 . Setscrew, hex head, M8 x 20 mm long011073 4 . Nut, hex, M8 Nyloc
6 014845 1 Pocket, cab prop (always fitted nearside)011075 2 . Nut, hex, M10 Nyloc
7 036403 1 . Cab prop guide000052 2 . . Setscrew, hex head, M5 x 16 mm long0001551 2 . . Nut, hex, M5 Nyloc
8 013465 2 Hopper guide011011 2 . Setscrew, hex head, M8 x 25 mm long011073 2 . Nut, hex, M8 Nyloc
9 013402 2 Mudguard10 013404 4 . Bracket, mudguard
011032 3 . . Setscrew, hex head, M10 x 30 mm long011075 3 . . Nut, hex, M10 Nyloc
11 011640 1 PIN, HOPPER HINGE...............................................................Page G112 014001 2 . Bush (pair)
000050 4 . . Screw, slotted round head, 2BA x ” long000005 4 . . Nut, hex, 2BA Nyloc
13 013996 1 . Bush (pair)000050 2 . . Screw, slotted round head, 2BA x ” long000005 2 . . Nut, hex, 2BA Nyloc
14 033232 1 HANDBRAKE ABUTMENT ........................................................Page D5011010 2 . Setscrew, hex head, M8 x 20 mm long011073 2 . Nut, hex, M8 Nyloc
15 028786 1 Rear Bumper (dual sweep vehicles only)16 033017 1 . Bracket, rear bumper, LHNI 033018 1 . Bracket, rear bumper, RHNI 028785 2 . End cap, rear bumper
011414 2 . . Coach bolt, M8 x 30 mm long011073 1 . . Nut, hex, M8 Nyloc
17 011757 1 Hopper prop pocket (always fitted nearside)011001 2 . Setscrew, hex head, M8 x 25 mm long011073 2 . Nut, hex, M8 Nyloc
18 032562 1 Bracket, cab support, LHNI 032563 1 Bracket, cab support, RH
011011 8 . Setscrew, hex head, M8 x 25 mm long011073 8 . Nut, hex, M8 Nyloc
19 023346 1 Bracket, widesweep tow, LHNI 023347 1 Bracket, widesweep tow, RH
011031 2 . Setscrew, hex head, M10 x 25 mm long011043 2 . Bolt, hex head, M10 x 70 mm long011073 4 . Nut, hex, M8 Nyloc
Continued...
CHASSIS GENERAL ARRANGEMENT (DUAL SWEEP SHOWN)
1
4
5
2,3
8
11
12
13
14
16
15
1718
199,10
6
7
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
CHASSIS GENERAL ARRANGEMENT20 013853 1 Bracket, widesweep lift, LH/RH
011011 4 . Setscrew, hex head, M8 x 25 mm long011073 4 . Nut, hex, M8 Nyloc
21 033267 1 Cover, LH drive NI 014398 1 Cover, RH drive
011071 3 . Nut, hex, M6 Nyloc010545 1 . Titanfast013426 1 . Screw, Pan head, M8 x 2 0mm long011073 10 . Nut, hex, M8 Nyloc
22 032627 1 Bracket, hopper raise sensor 23 032627 1 . HOPPER RAISE SENSOR ........................................................Page K524 021640 Pair Chassis rail25 011599 2 Hopper ram trunnions
011031 8 . Setscrew, hex head, M10 x 25 mm long011075 8 . Nut, hex, M10 Nyloc
26 034948 1 Cross member (rear front)27 013418 1 Cross member (rear middle)
011011 6 . Setscrew, hex head, M8 x 20 mm long011012 4 . Setscrew, hex head, M8 x 30 mm long011073 10 . Nut, Nyloc, M8
28 032035 1 Cross member (rear back), Also available as kit Part No 032039NI 032036 1 . Bracket, LHNI 032037 1 . Bracket, RH
011012 12 . Setscrew, hex head, M8 x 30 mm long011073 12 . Nut, hex, M8 Nyloc
NI 014835 1 Cross member (front)NI 013938 1 Label, load apportioning valve (LAV)
011125 4 . Rivet, blind, 3.2 mm x 10 mm long29 013998 1 Bracket, rear light cluster, LH30 013999 1 Bracket, rear light cluster, RH31 012934 1 Bracket, number plate
011010 4 . Setscrew, hex head, M8 x 20 mm long011073 2 . Nut, hex, M8 Nyloc
NI 033758 1 Bracket, steering box, RH ...................................................Page C17NI 033759 1 Bracket, steering box, LH....................................................Page C17
011052 4 . Setscrew, hex head, M12 x 30 mm long011077 4 . Nut, hex, M12 Nyloc011011 2 . Setscrew, hex head, M8 x 25 mm long011073 2 . Nut, hex, M8 Nyloc
32 021436 1 TANK, FUEL (DUAL SWEEP VEHICLES ONLY)......................... Page A7NI 032654 1 TANK, FUEL (SINGLE SWEEP VEHICLES ONLY) ...................... Page A7NI 031244 1 Cover, fuel tank (dual sweep vehicles only)NI 024106 1 . Clamp, fuel tank cover, InnerNI 024107 1 . Clamp, fuel tank cover, Outer
011011 2 . Setscrew, hex head, M8 x 25 mm long011073 2 . Nut, hex, M8, Nyloc
CHASSIS GENERAL ARRANGEMENT (DUAL SWEEP SHOWN)
20
21
22
2324
25
26
2728
29
30
3132
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
GANTRY GENERAL ARRANGEMENT1 033760 1 Gantry frame LH leg 2 033761 1 Gantry frame RH leg - EURO 4
011031 8 . Setscrew, hex head, M10 x 25 mm long036454 8 . Safety washer, Schnorr027156 8 . Spacer, hex, M10
NI 026728 1 . Gantry cross member front - EURO 4011031 2 . . Setscrew, hex head, M10 x 25 mm long011095 2 . . Washer, M10, spring 011074 2 . . Washer, M10, plain011075 2 . . Nut, hex, Nyloc M10
NI 026729 1 . Gantry cross member rear - EURO 4011031 4 . . Setscrew, hex head, M10 x 25 mm long011095 4 . . Washer, M10, spring011074 4 . . Washer, M10, plain011075 4 . . Nut, hex, M10 Nyloc
3 025143 1 OIL TANK ASSEMBLY .............................................................Page J134 034130 1 RADIATOR ASSEMBLY ..................................................Page A3 & J115 032985 1 Battery 12 Volt 90 Ah - EURO 46 014834 1 Cab locking strap
011011 4 . Setscrew, hex head, M8 x 25 mm long011073 4 . Nut, hex, M8 Nyloc
7 021904 1 . Eye bolt, cab lock011029 1 . . Screw, socket cap head, M8 x 35 mm long
8 025279 1 AIR CLEANER ASSEMBLY - EURO 4 ........................................ Page A39 NA 1 . ECU & NODE ENCLOSURE - EURO 4 ....................................Page K3
NI 027742 1 . MANIFOLD OIL TANK FEED.................................................Page J1110 025148 1 . MANIFOLD OIL RETURN .....................................................Page J11NI 026866 1 WATER PUMP, ELECTRIC........................................................ Page H3 11 026790 1 BRUSH BLOCK ASSEMBLY ......................................................Page J312 026787 1 VALVE BLOCK MAIN ASSEMBLY ...........................................Page J113 026420 1 Bracket, extension panel LH upper
011067 2 . Setscrew, hex head, M6 x 25 mm long011090 4 .Washer, M6, plain011073 2 . Nut, hex, M8 Nyloc
14 026421 1 Bracket, extension panel RH upper011067 2 . Setscrew, hex head, M6 x 25 mm long011090 4 . Washer, M6, plain011073 2 . Nut, hex, M8 Nyloc
NI 023231 4 . Receptacle Dzus15 026949 1 Bracket, extension panel LH bottom16 026950 1 Bracket, extension panel RH bottom
NOTE:Unless stated all parts are common for EURO 4 and 5 models
GANTRY GENERAL ARRANGEMENT
5
8
1
4
2
3
6
7
12
1110
13,14
15,16
9
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
GANTRY GENERAL ARRANGEMENT - EURO 5 NI 037144 1 Gantry frame, RH leg1 037149 1 . Gantry, cross member shelf
011030 4 . . Setscrew, hex head, M10 x 20 mm long036454 4 . . Washer, Schnorr saftey, VS10011075 4 . . Nut, hex, M10 nyloc
2 037160 1 . Water services, hanger plate011073 4 . . Nut, hex, M8 nyloc
NI 037161 1 . Bracket, water services, hanger plate, rear011075 2 . . Nut, hex, M8 nyloc
NI 037162 1 . Bracket, water services, hanger plate, front011075 2 . . Nut, hex, M8 nyloc
3 037157 1 . ECU housing4 037158 1 . Cover, ECU housing5 037159 1 . ECU shelf
011075 2 . . Nut, hex, M8 nyloc6 037151 1 . ECU, housing carrier, front
011030 1 . . Setscrew, hex head, M10 x 20 mm long036454 4 . . Washer, Schnorr saftey, VS10011075 1 . . Nut, hex, M10 nyloc
7 037152 1 . ECU, housing carrier, rear011030 1 . . Setscrew, hex head, M10 x 20 mm long036454 4 . . Washer, Schnorr saftey, VS10011075 1 . . Nut, hex, M10 nyloc
NI NA 1 . ECU ...................................................................................Page K58 037150 1 . Bracket, air filter
000105 4 . . Screw, socket caphead, M8 x 20 mm long011093 4 . . Washer, M8, spring
9 037165 1 . Bracket, exhaust, lower011010 3 . . Setscrew, hex head, M8 x 20 mm long011093 3 . . Washer, M8, spring011092 3 . . Washer, M8, plain
10 013764 4 . Bracket, exhaust, upper011010 4 . . Setscrew, hex head, M8 x 20 mm long011093 4 . . Washer, M8, spring011092 4 . . Washer, M8, plain
11 037153 1 . Fairing carrier, upper000105 4 . . Screw, socket caphead, M8 x 20 mm long011093 4 . . Washer, M8, spring
12 037425 1 . Bracket, controller 011001 2 . . Setscrew, hex head, M6 x 16 mm long011071 2 . . Nut, hex, M6 nyloc
13 037228 1 . . Controller, CR2500 .............................................................Page K5000052 4 . . . Setscrew, hex head, M5 x 16 mm long000155 4 . . . Nut, hex, M5 nyloc
14 037154 1 . Bracket, node support011010 2 . . Setscrew, hex head, M8 x 20 mm long011093 2 . . Washer, M8, spring
15 032539 2 . Node (CANbus)....................................................................Page K5000020 4 . . Setscrew, M6 x 30 mm long011090 8 . . Washer, M6, plain011071 4 . . Nut, hex M6 nyloc
2
3
4
5
67
8
9
10
11
VEIWED FROM REAR
1
12 14
13
15
GANTRY GENERAL ARRANGEMENT - EURO 5
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
em Part Number Quantity Description
FRONT MUDFLAP ASSEMBLY1 014745 2 Mudflap2 014738 1 . Bracket, mud flap LH3 014739 1 . Bracket, mud flap RH4 026625 2 . Clamp strip, mud flap
011001 6 . . Setscrew, hex, M6 x 16 mm long011071 6 . . Nut, hex, M6 Nyloc011091 6 . . Washer, M6, spring
item Part Number Quantity Description
REAR MUDGUARD ARRANGEMENT (Showing Blanking Plate)1 013402 2 Mudguard (J22)2 013404 4 . Bracket3 014162 4 . Stay mudguard4 012954 4 . Bracket back plate
011010 24 . . Setscrew, hex head, M8 x 20 mm long011073 24 . . Nut, hex, M8 Nyloc
5 011766 1 Suction tube blanking plate6 010502 1 . Handle7 023275 1 . Bracket8 013506 2 . Pin, locating9 013507 2 . Linch pin and chain
FRONT MUDFLAP ASSEMBLY
REAR MUDGUARD ASSEMBLY
1
5
2,3,48,9
1
2
3
4
6
7
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 10
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
FRONT SUSPENSION ASSEMBLY1 037041 2 Leaf spring, front
NI 023627 4 . Spring bush011127 4 . . Bolt, hex head, M14 x 110 mm long011077 4 . . Nut, hex, M14
NI 100013 2 . Bush, 2 013849 4 . Shackle, front spring
034244 4 . . Bolt, hex head, M12 x 110 mm long011077 4 . . Nut, hex, M12
3 027671 2 . Clamp, stabiliser bar4 027670 2 . Clamp bush, rubber
011073 4 . . Setscrew, hex head, M8 x 25 mm long011092 4 . . Washer, M8, plain011073 4 . . Nut, hex, M8
5 027668 1 . Stabiliser bar6 100134 2 . Drop link
011077 4 . . Nut, hex, M127 100035 2 . Shock absorber
011055 2 . . Bolt, hex head, M12 x 65 mm long011096 6 . . Washer, M12, plain011077 4 . . Nut, hex, M12
8 014639 2 . Top plateNI 023343 1 . Packer (fitted to near- side only)
000162 4 . . Bolt, hex head, M14 x 110 mm long (used without packer)000163 4 . . Bolt, hex head, M14 x 120 mm long (used with packer)000164 8 . . Nut, hex, M14000315 1 . . Screw, socket caphead, M10 x 90 mm long leaf spring centre
(near-side only)9 013755 2 . Bump stop
011053 2 . . Setscrew, hex head, M12 x 35 mm long011077 2 . . Nut, hex, M12
10 021611 1 . . AXLE BEAM .......................................................................Page C15
NOTE: Front leaf spring must be order as a pair on all models prior to serial number 6924. If in doubt contact Scarab spares department quoting serial number and model.
FRONT SUSPENSION & ASSOCIATED PARTS
1
2
3
4
5
6
7
8
9
10
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 12
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
13 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
REAR SUSPENSION ASSEMBLY1 025573 1 AXLE ASSEMBLY REAR ............................................................Page B72 037040 2 Leaf spring, Rear
NI 100524 4 . Spring bush011133 2 . . Bolt, hex head, M16 x 100 mm long (spring to shackle)011060 2 . . Nut hex, M16011422 2 . . Bolt, hex head, M20 x 110 mm long ( spring to chassis)011082 2 . . Nut, hex, M20
3 100029 2 . Shackle (RH drive vehicles)NI 023345 1 . Shackle (replaces 100029 nearside on LH drive vehicles)4 027669 1 . Stabiliser bar5 027671 2 . . Clamp, stabiliser bar6 027670 2 . . Clamp bush, rubber
011073 4 . . Setscrew, hex head, M8 x 25 mm long011092 4 . . Washer, M8, plain011073 4 . . Nut, hex, M8
7 100035 2 . Shock absorber011055 2 . . Bolt, hex head, M12 x 65 mm long011077 4 . . Nut, hex, M12
8 020657 2 . Axle packer9 034005 2 . Packer shim
10 100132 4 . U-Bolt011060 8 . . Nut, hex, M16011135 8 . . Washer, M16, plain
11 100134 2 . Drop link011077 4 . . Nut, hex, M12
12 013755 2 . Bump stop011053 2 . . Setscrew, hex head, M12 x 35 mm long
13 024064 1 Load sensor14 024067 1 . Bracket, load sensor mounting15 035610 1 . Adjustable bracket (load sensor actuator)16 033275 1 . . Bracket, load sensor actuator
000155 2 . . . Nut, hex, M5 Nyloc000171 2 . . . Screw, socket cap head, M5 x 35 mm Long011011 2 . . . Setscrew, hex head, M8 x 25 mm long011092 2 . . . Washer, M8, plain011073 2 . . . Nut, hex, M8 Nyloc
17 024065 1 . Cable glandNI 031649 1 . Wiring loom, load indicator18 034691 4 Road wheel complete with tyre }SEE NOTE034690 4 . Road wheel .
013463 4 . . Tyre 195R x 14CNI 028807 12 . . Wheel nut, LH 27 mm A/F NI 028808 12 . . Wheel nut, RH 27 mm A/F19 020315 2 . . Flex valve extension (complete)
028809 4 . . Dust cap
NOTE: Rear leaf spring must be order as a pair on all models prior to serial number 6924. If in doubt contact Scarab spares department quoting serial number and model.
The Original 5J Road Wheel was Replaced by the 5.5J on May/June 2008.Under no Circumstance must Wheels be Mixed on any Axle.
REAR SUSPENSION & ASSOCIATED PARTS
2
3
456
1
7
8
910
11
12
18
19
RearAxle
13
14
15
16
17
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 14
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
15 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
FRONT AXLE - STEERING HUB ARRANGEMENT 1 021611 1 Axle beam2 034673 1 . Stub axle, RH
NI 034672 1 . Stub axle, LH3 021620 2 . . Swivel pin
021631 4 . . Circlip4 021616 4 . . Bearing, needle roller5 036773 2 . . Plate, lower wear6 036772 2 . . Bearing, thrust plate7 036774 2 . . Plate, upper wear
NA 036775 2 . . Bearing, thrust plate kit8 021633 4 . . . O-ring9 021610 4 . . . End cap
10 021632 4 . . . Grease nipple, ” UNF11 021622 2 . . . Cotter pin
021627 2 . . . . Spring washer021626 2 . . . . Nut, hex, ” UNF
12 021634 As Req . . . . Shim 0.046 - 0.050
Use as required to achieve aclearance of 0.02 mm to 0.08 mm}021635 As Req . . . . Shim 0.051 - 0.055
021636 As Req . . . . Shim 0.056 - 0.060021637 As Req . . . . Shim 0.061 - 0.065021638 As Req . . . . Shim 0.036 - 0.042021639 As Req . . . . Shim 0.066 - 0.070021842 1 Swivel pin repair kit comprising of items 3 to 10
NI 1 . STEERING BOX ....................................................................Page C1713 014592 1 . Hub assembly LHNI 014593 1 . Hub assembly RH14 014594 2 . . Disc front
014627 10 . . . Stud (hub to disc)014595 10 . . . Nut (hub to disc)014596 10 . . . Lock washer (Hub to Disc)
15 021671 2 . . Brake disc shield011098 4 . . . Washer, “, spring000063 4 . . . Bolt, hex, “ UNF x ”
16 014601 1 . . BRAKE CALLIPER ASSY LH ..................................................Page D3NI 014602 1 . . BRAKE CALLIPER ASSY RH..................................................Page D317 011014 2 . . Screw, socket button head M8 x 40 mm long }Stop adjuster011072 2 . . . Nut, hex, M8 (locking nut)18 014605 2 . . Grease cap19 014626 2 . . Oil seal20 021641 2 . . Locking cap
014768 2 . . . Washer, axle D021642 2 . . . Nut, ” UNF021643 2 . . . Split pin ” x 1 ”
NI 014619 2 Front hub bearing kit21 014597 6 . . Wheel stud front LHNI 014598 6 . . Wheel stud front RH
028808 6 . . . Nut (per road wheel) 27 mm A/FNI 034690 2 . . Road wheel } SEE NOTENI 034691 2 . . Road wheel complete with tyreNI 014819 2 . . . Hub cover
NOTE: The Original 5J Road Wheel was Replaced by the 5.5J on May/June 2008.Under no Circumstance must Wheels be Mixed on an
FRONT AXLE (STEERING)
1
RIGHT HAND SIDEVIEWED FROM FRONTAXLE & SWIVEL REPAIR KIT PARTS
10
3
10
9
92
11
4
5
8
12
15
17
20
1916
ROAD WHEEL & TYRE
LEFT HAND SIDE
RIGHT HAND SIDE13
18
14
67
2
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 16
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
17 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
STEERING ARRANGEMENT1 033056 1 Steering box, LH drive vehicles2 033759 1 . Bracket, mounting, steering box, LH3 033861 1 . Support, steering box, LH
NI 033057 1 . Steering box, right hand drive (TWR)NI 033758 1 . Bracket, mounting, steering box, RHNI 033862 1 . Support, steering box, RH4 033058 2 . Drop arm5 028187 2 . Drag link (complete with ball joints)6 028186 2 . Ball joint, front, left hand thread (drop link end)
031926 2 . Nut, ball joint locking, left hand thread031925 As Req . Washer, locking
7 028180 2 . Ball joint, rear, right hand thread (steering arm end)031924 2 . Nut, ball joint locking, left hand thread031925 As Req . Washer, locking
8 035841 1 . Steering arm assembly, left hand drive021628 1 . . Key, Woodruff021629 2 . . Nut, ” UNF, Nyloc032696 1 . . Washer, special
NI 035842 1 . Steering arm assembly, right hand drive021628 1 . . Key, Woodruff021629 2 . . Nut, ” UNF, Nyloc self-locking032696 2 . . Washer, special
9 021648 2 . Track rod 10 028180 2 . Ball joint, right hand thread (right hand front wheel side)11 028186 2 . Ball joint, left hand thread (left hand front wheel side)12 021644 4 . Clamp, track rod end
000249 2 . . Screw, socket cap head, M10 x 40 mm long011074 2 . . Nut, hex, M10
13 022854 2 . Arm, track rod, RHNI 021628 2 . . Key, Woodruff
021629 2 . . Nut, hex, ” UNF14 022855 2 Arm, track rod, LHNI 021628 2 . . Key, Woodruff
021629 2 . . Nut, hex, ” UNF
For details relating to the steering wheel and column, please refer to Page E9
1
Front Axle (Ref. Only)
2
3
4
9
6
7
5
5
7
9
8
1012
1211
13
14
STEERING ARRANGEMENT
NOTE:Left hand drive example illustrated. On right hand drive vehicles, the steering box and related components are located on the opposite side of the vehicle.
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 18
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
19 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
TEAL HAND WASH BASIN ASSEMBLY1 NI 1 Tank, part of Teal hand wash unit
011001 4 . Bolt, hex head, M6 x 16mm long011071 4 . Nut, hex, M6, Nyloc
2 033112 1 . Bracket, tank, LH3 033113 1 . Bracket, tank, RH4 033268 1 . Adaptor, reducing, ” UNF to ” BSP female5 010910 1 . . Elbow, galvanised, ” BSP, M/F6 003010 1 . . . Hose tail, ” BSP x ”7 010950 As Req . . . . Hose, black, ” ID, Gripflex8 010964 2 . . . . . O-Clip, ”9 036168 1 . Cover, Teal tank
011001 4 . . Setscrew, hex head, M6 x 16 mm long10 023194 1 . Cover, hydraulic valve block
026417 4 . . Stud, turn-lock, Dzuz023229 1 . . . Stud retainer, Dzuz011094 1 . . . Washer, M10, plain
NI 031838 1 . . Bracket, Teal cover, LH014025 2 . . . Spacer
NI 031839 1 . . Bracket, Teal cover, RH014025 2 . . . Spacer
NI 033237 2 . . Bracket, Teal cover, lower11 NI 1 . Basin & cover (part of Teal hand wash unit)12 033121 1 . Hinge, Teal basin & cover, RH
NI 1 . . Washer, white (part of Teal unit - fits between hinge & cover)NI 1 . . Setscrew, hex head, M6 x 12mm long (part of Teal unit)011077 1 . . Nut, hex, M12, Nyloc
NI 033123 1 . Hinge, Teal basin & cover, LHNI 1 . . Washer, white (part of Teal unit - fits between hinge & cover)NI 1 . . Setscrew, hex head, M6 x 12mm long (part of Teal unit)011077 1 . . Nut, hex, M12, Nyloc
13 012253 1 . . Fastener, Antiluce14 012969 1 . . . Washer, rubber15 033124 1 . . . Bracket, mounting16 010503 2 . . Fastener, wash basin, Gravelly17 NI 1 . Tap (part of Teal hand wash unit)NI 033269 1 . . Adaptor, reducing, ” UNF to ” BSP maleNI 010910 1 . . . Elbow, galvanised, ” BSP, M/FNI 003010 1 . . . . Hose tail, ” BSP x ” hoseNI 033120 1 . Wiring loom
1
2
3
4,5,6
7,8
9
11 11
10
12
16
17
13,14,15
ILLUSTRATED PARTS CATALOGUE Section CSCARAB VM MINOR - CANbus Page 20
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 CHASSIS
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
C
C Section ILLUSTRATED PARTS CATALOGUE
21 Page SCARAB VM MINOR - CANbus
CHASSIS Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION DBRAKES & RELATED COMPONENTS
TABLE OF CONTENTS
Assembly/Description Page
Braking system - piping & valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Brake pedal assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Front brake callipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Rear brake arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Handbrake arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
NOTE:Unless stated all parts are common for EURO 4 and 5 models
D Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Brakes & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
BRAKING SYSTEM - GENERAL ARRANGEMENT1 014748 1 Brake load apportioning valve (LAV)2 014816 3 Brake hose MEL 508153 014817 2 Brake hose MEL 509284 014818 2 . Tee adaptor, brake hose5 014212 1 Connector, ” Kunifer6 035598 1 Brake pipe RH, server to front brakes
NI 035648 1 Brake pipe LH, server to front brakes7 035599 1 Brake pipe RH, server to rear brakes
NI 035647 1 Brake pipe LH, server to rear brakes 8 033847 1 Brake pipe, tee to front brakes9 033846 1 Brake pipe, tee to front brakes
10 033845 2 Brake pipe, rubber hose to front brakes11 033851 1 Brake pipe, rubber hose to rear Connector12 033849 1 Brake pipe, connector to LAV valve13 033850 1 Brake pipe, tee to LH rear brake14 033848 1 Brake pipe, tee to RH rear brake
item Part Number Quantity Description
BRAKE PEDAL ASSEMBLY1 014648 1 Brake servo, complete with master cylinder
011075 3 . Nut, hex, M102 014648 1 . Master cylinder
NI 100444 1 . . Repair kit, master cylinder3 034789 1 . Mounting bracket, brake Assembly
000021 3 . . Setscrew, hex head, M6 x 40 mm long011071 3 . . Nut, hex, M6, Nyloc
4 032910 1 . . Switch, stoplight5 014812 1 . Adaptor Plate, master cylinder
000081 2 . . Setscrew, hex head, ” UNC x ”6 014813 1 . Mounting bracket, remote reservoir
011003 2 . . Setscrew, hex head, M6 x 50 mm long011071 2 . . Nut, hex, M6, Nyloc
7 014784 0.7 metre . . Hose 7.5 x 15 Dia010960 4 . . . O Clip ”
8 014811 2 . . . Hosetail, remote reservoir9 014783 2 . . . Seal, reservoir mounting
10 100123 1 . . Hose assembly, servo vacuum11 034787 1 . Brake pedal. LH drive12 034788 1 . Brake pedal. RH drive13 100044 1 . . Spring, brake pedal14 013421 1 . . . Spacer, cab pivot
000075 1 . . . . Bolt, hex, M10 x 130 mm long011075 1 . . . . Nut, hex, M10, Nyloc100097 1 . . . . Clevis pin100108 1 . . . . . Split pin
15 030029 1 . . . . Reservoir (spare)16 030027 1 . . . . . Cap (remote mounted reservoir)17 030028 1 . . . . . Cap float and switch (remote mounted reservoir)
BRAKE CIRCUIT COMPONENTS
4
5
3
1
2
2
3
4
2
3
14
13
46
6
7
10 8,9
BRAKE PEDAL ASSEMBLY
11,12
15,16,17
LEGENDSteel Pipes =Rubber Hoses =
For information related to steel brake pipes and fittings please contact our Parts Department stating Vehicle serial number and identifying the section of pipe required.
BRAKEMASTERCYLINDER
RIGHT HANDFRONT BRAKE CALLIPER
LEFT HANDFRONT BRAKE CALLIPER
REAR BRAKEDRUMS
2
6
7
8 10
9
11
12
13
14
10
1
ILLUSTRATED PARTS CATALOGUE Section DSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Brakes & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
D
D Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Brakes & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
FRONT BRAKE CALIPER1 014601 1 Calliper, brake assembly, LH1 014602 1 Calliper, brake assembly, RH2 021772 2 . Bolt, calliper mounting kit (VEHICLES BEFORE APRIL 2008)2 011412 2 . Bolt, calliper mounting kit (VEHICLES AFTER APRIL 2008)
NI 023323 2 . Pin & spring clip set3 020138 1 . Disc pad set ( 4 pads)4 020139 1 . Disc brake repair kit (1 Wheel)5 023323 1 . Pin and spring clip kit6 000238 2 . Bleed Nipple7 014816 2 Hose, brake pipe8 014774 1 . Brake pipe hose bracket (LH)8 014775 1 . Brake pipe hose bracket (RH)9 033845 1 Calliper Steel brake pipe
10 014594 2 BRAKE DISC, FRONT .............................................................Page C13
NOTE: For other Steel brake pipes contact SCARAB SPARES DEPT
item Part Number Quantity Description
REAR BRAKE ARRANGEMENT1 020134 1 Brake assembly, LH complete 1 020133 1 Brake assembly, RH complete2 020118 1 . Back plate, LH2 020117 1 . Back plate, RH3 020119 1 . . Plug, rubber4 020128 1 . . Wheel cylinder, LH4 020127 1 . . Wheel cylinder, RH
NI 003018 AsReq . . . Clip, wheel cylinder5 020129 1 . . . Bleed screw6 020126 AsReq . . Seal kit, wheel cylinder7 020120 1 . Brake shoe kit (complete axle set)8 020125 1 . . Shoe hold down kit9 020121 1 . . Adjuster kit (complete axle set)
10 020124 1 . Handbrake lever, LH10 020123 1 . Handbrake lever, RH11 020122 1 . . Pivot pin kit12 020132 1 . Cross lever13 020131 1 . . Spring kit, LH13 020130 1 . . Spring kit, RHNI 020199 1 Brake drum
FRONT BRAKE CALIPER ASSEMBLY
1
4
3
5
6
2
REAR BRAKE ASSEMBLY
12
1
7
12,13
8
4
6
3
2 5
9
10
11
7
10
8
9
ILLUSTRATED PARTS CATALOGUE Section DSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Brakes & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
D
D Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Brakes & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
HANDBRAKE ASSEMBLY1 026792 1 Support, hand brake
011011 3 . Setscrew, hex head, M8 x 25 mm long011073 7 . Nut, hex, M8, Nyloc
2 026811 1 . Lever, hand brake3 100105 1 . . Clevis pin
100106 1 . . . Split pin4 014821 1 . . Cable, hand brake, primary (8 mm eyelet)
4a 035679 1 . . Cable, hand brake, primary, RH routing9 012876 1 . . . Grommet, I/D 11 mm - O/D 19 mm5 032910 1 Handbrake switch6 032051 1 . Handbrake switch plunger7 032049 1 . Support bracket8 033218 1 . . Wiring loom
NI 027790 1 . . . Pin kit10 100096 1 . . Equalizer11 100097 4 . . . Clevis pin
100108 4 . . . . Split pin12 100047 1 . . . Spring, brake retracting13 100278 1 . . . Cable, secondary (drum to drum)14 033235 2 . Link15 033234 1 . Cranked link
HANDBRAKE ASSEMBLY
10, 11
12
13
1
2,3
45, 6, 7, 8
9
14 15
HANDBRAKE LINKAGE ON RH SIDE
HANDBRAKE LINKAGE ON LH SIDE
ILLUSTRATED PARTS CATALOGUE Section DSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Brakes & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
D
D Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Brakes & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION ECAB ASSEMBLY & RELATED COMPONENTS
Table of Contents
Assembly/Description Page
CAB ASSEMBLYCab - external components & associated parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Cab - Internal components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9Steering assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Cab safety latch assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Hydraulic assisted cab tilt (option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Hydraulic assisted cab tilt circuit (option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Cab heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Air conditioning compressor arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Air conditioning radiator arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
NOTE:Unless stated all parts are common for EURO 4 and 5 models
E Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
CAB EXTERNAL COMPONENTS AND ASSOCIATED PARTSCabTech Scarab
1 035004 036879 1 Cab body, standard modelNI 034841 1 Cab body, low roof model2 035173 036882 1 . Roof, GRP
NI 035182 037777 1 . . Roof insulation panel011033 6 . . Setscrew, hex head, M6 x 50 mm long011090 6 . . Washer, M6, plain
3 034842 036889 1 . Windscreen4 010304 1 . Beacon, 12 Volt5 030926 1 . Aerial6 013941 1 . Mirror, (ALWAYS FITTED OFF-SIDE)
NI 035125 037115 1 . . Mirror adaptor plate000377 2 . . . Screw, socket countersunk, ” UNF x ” long011068 2 . . . Setscrew, hex head, M6 x 40 mm long011091 2 . . . Washer, M6, spring 011090 2 . . . Washer, M6, plain
7 033107 2 . Mirror, LH/RH8 033108 2 . . Mirror arm
011068 4 . . . Setscrew, hex head, M6 x 35 mm long011090 4 . . . Washer, M6, plain
9 013941 1 . Mirror, dual sweep only (ALWAYS FITTED OFF-SIDE)000377 4 . . Screw, socket cap head, ” UNF x 1 ” long011091 2 . . Washer, M6, spring011090 4 . . Washer, M6, plain
10 035204 1 . Wiper arm, passenger side LH drive, driver side RH drive11 035209 1 . Wiper arm, driver side LH drive, passenger side RH driveNI 035205 2 . . Wiper blade12 035029 037123 1 . Headlight cover, GRP, RH
000384 3 . . Screw, flange head self-tapping, No10 x ” long13 034786 037132 1 . Grill
000384 3 . . Screw, flange head self-tapping, No10 x ” long14 035028 037122 1 . Headlight cover, GRP, LH
000384 3 . . Screw, flange head self-tapping, No10 x ” long15 035013 037118 1 . Light cluster bracket, RHNI 035012 036899 1 . Light cluster bracket, LH
000090 4 . . Screw, socket button head, M6 x 16 mm long011091 4 . . Washer, M6, spring 011090 4 . . Washer, M6, plain
16 034847 2 . Main beam & side light17 034850 2 . Front indicator18 034848 2 . Headlight dip beam19 036190 2 . Gas spring, cab tilt20 023110 2 . . Bellows, gas spring21 027734 2 . CAB PIVOT BRACKET................................................................Page C1
011038 2 . . Bolt, hex head, M10 x 80 mm long011095 4 . . Washer, M10, plain011075 2 . . Nut, hex, M10 Nyloc
22 034849 2 . Side indicator23 034844 037125 1 . Lower skirt, RHNI 034843 037124 1 . Lower skirt, LH
011001 8 . . Setscrew, hex head, M6 x 16 mm long011099 8 . . Repair washer, ”
Continued...
CAB GAS STRUT
12
345
6
7
8
9
10
11
12
13
14
16
17
18
15
19 20
21
22
23
CAB ARRANGEMENT (LEFT HAND-DRIVE SHOWN)
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
CAB EXTERNAL COMPONENTS AND ASSOCIATED PARTSCabTech Scarab
24 034846 036878 1 Door, RH (complete assembly)NI 034845 036877 1 Door, LH (complete assembly)25 035186 036886 1 . Glass, quarter light, front RHNI 035185 036885 1 . Glass, quarter light, front LH26 035456 027134 1 . Exterior pull handle, complete with gasketNI 036673 2 . . Exterior pull handle strengthening plate
000097 6 . . . Setscrew, hex head, M5 x 12 mm long27 035188 036881 1 Glass, quarter light, rear RH28 035187 036880 1 Glass, quarter light, rear LH29 034756 1 Cab extension RH (EURO 4)NI 036853 1 Cab extention RH (EURO 5)NI 034755 1 Cab extension LH
026417 8 . Dzus stud023229 24 . Retainer
30 036229 1 . Handle011010 2 . . Setscrew, hex, hd, M8 x 20 mm long000089 2 . . Dome nut, hex, M8
31 035193 036891 1 . Sliding window assembly RHNI 035192 036890 1 . Sliding window assembly LH32 037126 1 . Check strap, small33 037127 1 . Check strap, large 134 037128 1 . Check strap, large 2
011011 6 . . Setscrew, hex head, M8 x 25 mm long011093 12 . . Washer, M8011073 6 . . Nut, hex, M8 Nyloc
35 035451 037136 2 . . Squeeze lever000384 2 . . . Screw, flange head self-tapping, No10 x ” long
36 035190 036888 1 . . Door lower glass RHNI 035189 036887 1 . . Door lower glass LH37 035198 037112 1 . . Door cover/arm rest RHNI 035197 037111 1 . . Door cover/arm rest LH38 035198 037130 2 . . . Arm rest
000384 6 . . . Screw, flange head self-tapping, No10 x ” long39 035457 037138 1 . . Anti-burst latch RHNI 035452 037138 1 . . Anti-burst latch LH
000371 4 . . . Screw, socket countersunk, M8 x 25 mm long40 035170 037979 1 . . Door linkage41 035453 037902 2 . . Cable42 035103 037119 2 . Striker pin bracket43 035469 037133 2 . . Striker pin44 035468 037120 2 . . Striker pin cover
NOTE:When ordering parts, unsure the correct identifacation of the cab manufacture, The manufactures identifacationcan be obtain from the VIN plate, situated at the right hand rear of the cab, and will be either CabTech or Scarabsweeper Ltd.
24
25
2627
29
3031
32,33,34
28
35
36
37
39
40
41
42
4344
CAB ARRANGEMENT (LEFT HAND-DRIVE SHOWN)
38
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
CAB INTERNAL FEATURES1 020272 2 Grab handle
000350 4 . Screw, socket button head, M6 x 20 mm long2 033089 1 CANbus auxiliary control panel (door pod)
031798 1 . Overlay, CANbus auxiliary panel000304 2 . . Screw, socket button head, M4 x 10 mm long
NI 031626 1 . CANbus auxiliary control panel bracket, LHNI 031627 1 . CANbus auxiliary control panel bracket, RH
000338 . Screw, socket button head, M6 x 16 mm long3 032808 1 Panel, speedometer & driving instruments4 NA 1 STEERING COLUMN....................................................................Page E115 033088 1 CANbus main key pad & display panel
031797 1 . Overlay, CANbus main panel031951 1 . Rim, panel overlay000342 8 . . Screw, socket button head, M4 x 16 mm long
6 030587 1 Bottle, windscreen washer fluid with 12 volt pump030588 1 . Washer fluid bottle bracket000384 2 . . Screw, flange head self-tapping, No10 x ” long
7 013914 1 Switch housing8 031407 1 . Switch, beacon, off/on/on
031412 1 . . Switch symbol, insert9 031406 1 Switch, fog lights, off/on
031410 1 . Switch symbol, insert (fog lights)10 031406 2 Switch, side lights, off/on
031409 1 . Switch symbol, insert (side lights)11 031408 1 Switch, hazard warning lights
031412 1 . Switch symbol, insert (hazard warning lights)12 013259 2 . Blanking plate13 031599 1 Radio/CD player14 031639 1 RS232 connector
031997 1 . Cap, RS232 connector15 014958 2 Toolbox door16 021327 2 . Stud fastener
021328 2 . . Stud fastener retainer17 021326 2 . Fastener receptacle18 014959 4 . HingeNI 028320 4 . . Hinge spacer
000028 16 . . . Screw, slotted round head, 2BA x ” long011078 16 . . . Nut, hex, 2BA Nyloc
19 032617 1 Foot pedal, speed controller000329 2 . Screw, socket button head, M8 x 20 mm long011072 2 . Nut, hex, M8011093 2 . Washer, M8, spring 011092 2 . Washer, M8, plain
20 036680 2 Door protection strip21 036681 1 Floor protection strip22 013426 1 Floor plate23 NA 1 WIPER MOTOR..............................................................................Page E924 031893 1 Steering column cover
000338 4 . Screw, socket button head, M6 x 16 mm longNA 026161 1 CAB HEATER ...............................................................................Page E1925 031632 1 Heater control moduleNI 031633 1 Heater control module with air conditioning control (Option)
000304 4 . Screw, socket button head, M4 x 10 mm long000340 4 . Lug nut, M6
Continued...
CAB INTERIOR AND ASSOCIATED PARTS-LEFT HAND DRIVE SHOWN
1
2
4
5
3
6
7
8 9
12
13
18
19
20
21
1415
16
17
22
23
25
10
11 8
24
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
CAB INTERNAL FEATURESCabTech Scarab
26 035196 037778 1 Roof panel, soundproofing27 013514 1 Suction fan scraper
013631 2 . Clip, Fir Tree28 035195 1 Rear panel trimNI 035181 1 . Rear panel insulationNI 037779 1 . Rear panel insulation, middleNI 037780 2 . Rear panel insulation, side29 035459 1 Coat hanger30 013749 1 Interior light
000384 2 . Screw, flange head self-tapping, No10 x ” long31 025927 1 Seat, LHNI 025928 1 Seat, RH
011010 4 . Setscrew, hex head, M8 x 20 mm long011092 4 . Washer, M8, plain011073 4 . Nut, hex, M8 Nyloc
NI 025929 As req . Head rest (Option)32 036063 2 Seat belt guide
011001 4 . Setscrew, hex head, M6 x 20 mm long011090 4 . Washer, M6, plain011071 4 . Nut, hex, M6 Nyloc
33 031640 1 Dash, GRP, LH NI 031641 1 Dash, GRP, RH
000338 6 . Screw, socket button head, M6 x 16 mm long000340 6 . Lug nut, M6014563 7 . Fir tree button
34 031892 1 . Brake fluid access panel, LHNI 031894 1 . Brake fluid access panel, RH
031959 2 . . Arrow fastener35 031745 Pair Speakers, flush mounted36 018227 1 CAB LOCK ASSEMBLY ................................................................Page E1337 NA 1 HANDBRAKE ASSEMBLY..............................................................Page D5
011073 4 . Nut, hex, M8 Nyloc011092 4 . Washer, M8
38 034808 1 Centre console011115 4 . Screw, flange head self-tapping, No10 x ” long011145 4 . Washer, 2BA
39 013935 2 Sun visor000384 4 . Screw, flange head self-tapping, No10 x ” long
NI 020513 2 Seat belt40 013633 1 First aid box (Option)NI 037802 1 . Bracket, mounting, first aid box
000086 4 . Screw, slot head countersunk, M3 x 20 mm long000114 4 . Nut, hex, M3 Nyloc
41 1 Camera monitor (Option)NI 019123 1 HornNI 028108 1 Power socket, 12volt
NOTE:When ordering parts, unsure the correct identifacation of the cab manufacture, The manufactures identifacationcan be obtain from the VIN plate, situated at the right hand rear of the cab, and will be either CabTech os Scarab Sweepers Ltd.
Continued...
26
27
28
29
30
31
32
33 34
35
36
37
CAB INTERIOR AND ASSOCIATED PARTS
38
39
40
41
LEFT HAND DRIVE SHOWN
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
CAB INTERNAL FEATURES41 035432 1 Wiper linkage assembly, LH, complete with motorNI 035433 1 Wiper linkage assembly, RH, complete with motor42 035202 1 . Wiper motor43 036793 1 . . Crank arm44 NA 1 FUSE/RELAY PANEL.......................................................................Page K145 034792 1 . Fuse box access cover
021327 1 . Stud fastener021328 1 . . Stud fastener retainer021326 1 . Fastener receptacle014959 1 . Hinge000028 4 . . Screw, slotted round head, 2BA x ” long011078 4 . . Nut, hex, 2BA Nyloc
46 033214 1 Lower cover, heater/electrics, LHNI 033213 1 Lower cover, heater/electrics, RH
000350 3 . Screw, socket button head, M6 x 20 mm long000340 3 . . Lug nut, M6
47 031836 1 . Lower cover retainer NI 031837 1 . Lower cover retainer strip
000338 6 . . Screw, socket button head, M6 x 16 mm long48 026161 1 CAB HEATER ...............................................................................Page E19
000350 5 . Screw, socket button head, M6 x 20 mm long49 010478 1 Hand lance (Option)50 037103 1 . Hand lance retaining strap (after Nov 2009)NI 037104 1 . . Striker, hand lance retaining strap51 030595 1 . Hand lance retaining strap (before Nov 2009)52 011893 1 . Hand lance retaining ring
41
42
43
45
46
47
48
49
50
51
44
CAB INTERIOR AND ASSOCIATED PARTS-LEFT HAND DRIVE SHOWN
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 10
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
STEERING COLUMN ASSEMBLY & RELATED COMPONENTS1 031614 1 Steering column - upper2 031616 1 . Steering column - outer3 031617 1 . Ignition key switch/steering lock4 031618 1 . Spring5 032488 1 . Indicator switch bracket6 035604 1 . ø20 Starlock7 031621 2 . . Bearing 6004.2RSR8 031405 1 . Switch, gear select column 9 031404 1 . Switch, Multi-function column
000341 2 . . Screw, socket cap head M5 x 16 mm long10 100040 1 . Steering wheel
011096 1 . . Washer, M12, plain011077 1 . . Nut, hex, M12 Nyloc
11 100520 1 . . Boss cover, steering wheel (with Scarab Logo)12 033059 1 . Steering column - lower
} To secure splinedend clamps
000096 2 . . Screw, socket cap head, M8 x 40 mm long011073 2 . . Nut, hex, M8, Nyloc
For further details on the Scarab Minor steering system please refer to Page C15
STEERING COLUMN ASSEMBLY
10,11
98
3
5
1 2
7
12
4
6
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 12
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
13 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
CAB SAFETY LATCH ASSEMBLY1 033431 1 Cab latch
011073 1 . Nut, hex, M8 Nyloc011092 1 . Washer, M8, plain
2 033432 2 .Bracket, cab latch011067 1 . . Setscrew, hex head, M6 x 20 mm Long011071 1 . . Nut, hex, M6 Nyloc011090 1 . . Washer, M6, plain
3 033007 1 . Bracket, cab latch011010 2 . . Setscrew, hex head, M8 x 20 mm Long011073 2 . . Nut, hex, M8 Nyloc011092 2 . . Washer, M8, plain
4 033410 1 . Cab latch SpringNI 000040 1 . . Bolt, hex head, M10 x 55 mm Long (Latch Point)
011074 1 . . Nut, hex M10 full011075 1 . . Nut, hex M10 Nyloc
item Part Number Quantity Description
018227 1 Cab locking, complete assembly (Transverse operation)035775 1 Cab locking, complete assembly (In-line operation)
1 013866 1 . Base, transverse cab lock1 035773 1 . Base, in-line cab lock
NI 037050 1 . Support plate, cab latchNI 037051 1 . Packer, cab latchNI 035774 1 . . Nut plate, in-line cab lock
011010 2 . . Setscrew, hex head, M8 x 20 mm long011073 2 . . Nut, hex, M8 Nyloc011092 2 . . Washer, M6, plain000018 1 . . Bolt, hex head, M6 x 55 mm long011071 1 . . Nut, hex, M6 Nyloc011090 2 . . Washer, M6, plain
2 013869 1 . Link arm000018 1 . . Bolt, hex head, M6 x 55 mm long011071 1 . . Nut, hex, M6 Nyloc011090 2 . . Washer, M6, plain
3 013867 1 . Handle, cab lock011010 2 . . Setscrew, hex head, M8 x 20 mm long011073 2 . . Nut, hex, M8 Nyloc011092 4 . . Washer, M8, plain
4 013865 1 . . Knob, cab lock 5 013868 1 . . Hook, cab lock
011087 1 . . . Bolt, hex head, M6 x 25 mm long011071 1 . . . Nut, hex, M6 Nyloc011090 2 . . . Washer, M6, plain
6 021904 1 . Eye bolt011029 1 . . Screw, socket cap head, M8 x 35 mm long
7 014834 1 . Cab locking strap8 013466 2 . Bump stop9 037051 2 . . Support plate, bump stop
011013 4 . . . Setscrew, hex head, M8 x 35 mm long011073 4 . . . Nut, hex, M8 Nyloc
NOTE: The in-line operating cab locking assembly replaced the transverse assembly from January 2009IF in doubt contact your nearest dealer
I
1
2
4
CAB SAFETY LATCH ASSEMBLY
CAB LOCKING ASSEMBLY
4
1
2
3
5
3
67
8
9
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 14
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
15 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
HYDRAULICALLY ASSISTED CAB-TILT (OPTION)1 032810 2 Hydraulic ram, double acting2 011152 3 . Seal, Dowty, ” BSP3 011158 1 . Adaptor, ” BSP, M/M4 011169 2 . Elbow, swivel, ” BSP, M/F5 032469 1 . Valve, hose-break, ” BSP, M/F6 035443 2 . Bracket, upper pivot, outer7 035445 2 . . Space8 035444 2 . . Bracket, upper pivot, inner
011038 2 . . Bolt, hex head, M10 x 80 mm long011075 2 . . Nut, hex, M10 Nyloc
9 032830 1 . Step, LHNI 032831 1 . Step, RH10 011269 1 . Adaptor, bulkhead, ” BSP, M/M11 032474 2 . Pin, lower pivot
000084 2 . . Pin, split, ” x 1” long12 033261 1 Bracket, hand-pump mounting,
011011 4 . Setscrew, hex head, M8 x 25 mm long011073 4 . Nut, hex, M8 Nyloc
13 028307 1 . Hand pump14 013344 2 . . Spacer
000018 2 . . . Setscrew, hex head, M6 x 55 mm long011071 2 . . . Nut, hex, M6 Nyloc
15 011206 1 . Tee, swivel, ” BSP, M/M/F16 002005 1 . Tee, swivel, ” BSP, F/F/F17 010922 3 . . Hose tail, ” BSP x ” hose18 011257 1 . Valve, ball type, ” BSP, M/M19 012548 1 . . Bracket, valve mounting
011011 1 . . . Setscrew, hex head, M8 x 25 mm long011073 1 . . . Nut, hex, M8 Nyloc
20 027188 1 . . Adaptor, restrictor 0.5, ” BSP, M/M21 011171 1 . . Elbow, swivel, ” BSP, F/F
12,3,4,56,7,8
910,2,4
11
12 13
14
15,2,3
16,17,2,3
18
19
2,3
20,21,2,17
HYDRAULICALLY ASSISTED CAB-TILT (OPTION)
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 16
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
17 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
HYDRAULICALLY ASSISTED CAB-TILT CIRCUIT (OPTION)1 025142 1 HYDRAULIC OIL TANK ................................................................Page J132 025148 1 MANIFOLD, OIL RETURN.............................................................Page J113 010958 As req . Pipe, rubber, ” bore
010516 2 . . Clamp, worm drive, 11 - 16 mm4 010910 2 . Tee, ” BSP, galvanised, F/F/F5 010944 1 . Adaptor, ” BSP, galvanised, M/M6 010909 2 . Elbow, ” BSP, galvanised, M/F7 010922 2 . Hose tail, ” BSP x ” hose8 010958 As req . Pipe, rubber, ” bore
010516 2 . . Clamp, worm drive, 11 - 16 mm9 001105 1 . Hose, rubber, ” BSP x 400 mm long,
10 010958 As req . Pipe, rubber, ” bore010516 2 . . Clamp, worm drive, 11 - 16 mm
1 011257 1 . VALVE, BALL TYPE, ” BSP, F/F.................................................. Page E1512 028307 1 . PUMP, HAND............................................................................Page E1513 010985 1 . Hose, rubber, ” BSP x 2150 mm long, straight ends14 010981 2 . Hose, rubber, ” x 711 mm long, straight ends15 011180 1 . . Tee, “ BSP, M/M/M16 032810 2 . HYDRAULIC RAM, DOUBLE ACTING ......................................Page E1517 001062 2 . Hose, rubber, ” BSP x 850 mm long, straight end18 011158 2 . . Adaptor, ” BSP, M/M
8
9
10
11
12
1
2
3
13
14 14
15
16
17
16
18,4,6,7
4,5,6,7
HYDRAULICALLY ASSISTED CAB-TILT (OPTION)CIRCUIT COMPONENTS
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 18
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
19 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
CAB HEATER & OPTIONAL AIR-CONDITIONING ARRANGEMENT1 026161 1 Heater assembly, standard1 031776 * 1 Heater assembly, air-conditioning modification
NI 027708 1 . Blower assembly }Blower Assy and Matrix are locatedinside caseNI 027709 1 . Matrix
2 031844 1 . Valve, heater control3 030550 1 . . Spring clip (for valve/heater cable)4 027710 1 . Cable
NI TBA 1 metre . Vent pipe 2.5” Dia (Cab)NI 031867 1 . Blanking plate heaterNI 026261 1 . Kit, cab heater
* The Air-conditioner InstallationThis is a modification of the standard cab heater assembly. To ensure that the correct parts are supplied, please consult our parts department, stating your vehicle’s serial number, before ordering replacement parts
Item Part Number Quantity Description
AIR CONDITIONING-COMPRESSOR ARRANGEMENT 1 027715 1 Compressor unit2 034781 1 . Carrier, compressor unit *3 034782 1 . . Guard, lower4 033905 1 . . Cover5 033894 1 . . Hook, air-conditioning timing belt cover
NI 036169 1 . . Guard, lower (wide version )NI 036753 1 . . Bracket, support, timing belt cover6 025587 1 . . V Belt, A297 032704 1 . . Pulley
NI 033893 1 . . Pulley (VM Engine)NI 031633 1 CONTROL PANEL (CAB) ..............................................................Page E5NI 033993 1 . WIRING LOOM - CONTROL PANEL ..........................................Page K5NI 038753 1 . Cover, belt support plateNI 037085 1 . Cover, belt support plate (upper)
NOTE: The carrier * for the compressor unit as listed here and shown opposite (Item 2) is to the latest design as at the time of publication. This can be retro-fitted to earlier installations that use different supports, that are no longer available, but will require a fitting kit. For details please contact our parts and service dept.
CAB HEATER ASSEMBLY
1
2,34
PART OF AIR-CONDITIONINGMODIFICATIONS
6
12
3
4
5
67
AIR-CONDITIONING COMPRESSOR ARRANGEMENT
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 20
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
21 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
AIR CONDITIONING-RADIATOR ARRANGEMENT 1 029977 1 Condenser/radiator2 033853 1 . Cradle, condenser/radiator
011011 2 . . Setscrew, hex head, M8 x 25 mm long011092 2 . . Washer, M8, plain
NI 033855 2 . . Spacer, cradle hinge3 010509 2 . Toggle fastener
000161 4 . . Screw, countersunk slot head, 2BA x ” long011078 4 . . Nut, hex, 2BA Nyloc
4 021841 2 . Hook, toggle fastener000161 4 . . Screw, countersunk slot head, 2BA x ” long011078 4 . . Nut, hex, 2BA Nyloc
5 032886 2 . Clamp, upper, condenser011071 4 . . Nut, hex, M6 Nyloc011090 4 . . Washer, M6, plain
6 033854 2 . Bracket, hinged, cradle011001 8 . . Setscrew, hex head, M6 x 20 mm long
7 028976 1 Receiver drier/black can011067 2 . Setscrew, hex head, M6 x 20 mm long011090 2 . Washer, M6, plain
8 034659 1 . Bracket, receiver drier011087 2 . Setscrew, hex head, M6 x 25 mm long011090 2 . Washer, M6, plain
NI 033997 1 WIRING LOOM - CONDENSER/RADIATOR.................................Page K5
12
34
5
6
7 8
AIR CONDITIONING-RADIATOR ARRANGEMENT
ILLUSTRATED PARTS CATALOGUE Section ESCARAB VM MINOR - CANbus Page 22
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Cab Components
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
E
E Section ILLUSTRATED PARTS CATALOGUE
23 Page SCARAB VM MINOR - CANbus
Cab Components Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION FSWEEPING & SUCTION EQUIPMENT
Table of Contents
Assembly/Description Page
SWEEPING EQUIPMENTWidesweep brush arrangement - single sweep machines . . . . . . . . . . . . . . . . . . . . . . . . 1Widesweep brush arrangement - dual sweep machines . . . . . . . . . . . . . . . . . . . . . . . . . 3Widesweep-brush lifting arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Front brush arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Front brush swing-out & Fixed arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Side brush arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Side brush swing-out arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SUCTION NOZZLESuction nozzle arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Suction nozzle lifting arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Wander Hose assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Overhead suction boom arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
NOTE:Unless stated all parts are common for EURO 4 and 5 models
F Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WIDESWEEP ARRANGEMENT - SINGLE SWEEP MACHINES1 023253 1 Cover, brush
011030 6 . Setscrew, hex head, M10 x 20 mm long011075 6 . Nut, hex, M10 Nyloc
2 010248 1 . Tensioner, complete with nuts & washersNI 010606 2 . . Carabiner3 030680 1 . Brush bar4 023252 1 . Tow bar, LH
NI 023251 1 . Tow bar, RH5 010689 2 . . Bush
011052 2 . . Setscrew, hex head, M12 x 25 mm long011077 2 . . Nut, hex, M12 Nyloc
6 NA 1 . SUPPORT, TOW BAR, LH .......................................................Page C1NA 1 . SUPPORT, TOW BAR, RH.......................................................Page C1
7 012524 2 . Shock absorber011035 2 . . Setscrew, hex head, M10 x 50 mm long011075 2 . . Nut, hex, M10 Nyloc011405 2 . . Nut, hex, ” UNF Nyloc
8 012548 2 . Bracket, mounting, shock absorberNI 027156 2 . . Spacer, hex
011031 4 . . . Setscrew, hex head, M10 x 25 mm long9 013647 1 . Core, brush
10 023471 28 . . Brush disc refill, Polypropylene11 023472 27 . . Spacer ring, brush disc12 013649 1 . . End cap, brush core
011417 4 . . . Screw, socket countersunk, ” UNC x 1” long13 010682 2 . End plate
011030 4 . . Setscrew, hex head, M10 x 20 mm long011075 4 . . Nut, hex, M10 Nyloc
14 NA 1 . MOTOR, HYDRAULIC, OMP200..........................................Page J17011053 2 . . Setscrew, hex head, M12 x 35 mm long011077 2 . . Nut, hex, M12 Nyloc
15 013648 1 . Shaft, brush drive16 013652 1 . Tube, brush drive17 010612 1 . Bearing, complete with locking collar
011053 2 . . Setscrew, hex head, M12 x 35 mm long011077 2 . . Nut, hex M12 Nyloc005052 1 . . Nipple, grease
18 022362 1 . Hanger, dust skirt011030 3 . . Setscrew, hex head, M10 x 20 mm long011075 3 . . Nut, hex, M10 Nyloc
19 031249 1 . Dust skirt20 022363 1 . . Clamp, dust skirt
011030 5 . . . Setscrew, hex head, M10 x 20 mm long011075 5 . . . Nut, hex, M10 Nyloc
*
WIDESWEEP ARRANGEMENT - LH SINGLE SWEEP SHOWN
1
2
3
4
5
6
7
8
910
11
12
13
14
15
16
17
18
19
20
Ch
ass
is r
ail, re
fere
nce
on
ly
Op
posi
te t
oe-b
ar
sup
port
& s
hock
ab
sorb
er
om
itte
d f
or
cla
rity
Op
posi
te e
nd
pla
teom
itte
d f
or
cla
rity
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WIDESWEEP ARRANGEMENT - DUAL SWEEP MACHINES1 023529 1 Cover, brush
011030 6 . Setscrew, hex head, M10 x 20 mm long011075 6 . Nut, hex, M10 Nyloc
2 010248 1 . Tensioner, complete with nuts & washersNI 010248 2 . . CarabinerNI 010525 1 . . Chain link3 023527 1 . Brush bar4 023531 1 . Tow bar5 010689 2 . . Bush
011052 2 . . Setscrew, hex head, M10 x 25 mm long011077 2 . . Nut, hex, M10 Nyloc
6 NA 1 . . SUPPORT, TOW BAR, LH .....................................................Page C1NA 1 . . SUPPORT, TOW BAR, RH.....................................................Page C1
7 012524 2 . Shock absorber011035 2 . . Setscrew, hex head, M10 x 50 mm long011075 2 . . Nut, hex, M10 Nyloc011405 2 . . Nut, hex, ” UNF Nyloc
8 012548 1 . Bracket, mounting, shock absorber RH011030 1 . . Setscrew, hex head, M10 x 20 mm long011075 1 . . Nut, hex, M10 Nyloc
NI 025327 1 . Bracket, mounting, shock absorber LH011030 1 . . Setscrew, hex head, M10 x 20 mm long
9 023528 1 . Core, brush10 023471 25 . . Brush disc refill, polypropylene11 023472 24 . . Spacer ring, brush disc12 013649 1 . . End cap, brush core
011417 4 . . . Screw, socket countersunk, ” UNC x 1” long13 010682 2 . End plate
011030 4 . . Setscrew, hex head, M10 x 20 mm long011075 4 . . Nut, hex M10 Nyloc
14 NA 1 . MOTOR, HYDRAULIC OMPW200 .......................................Page J17011031 2 . . Setscrew, hex head, 10 x 25 mm long011095 2 . . Washer, M10, spring
15 013648 1 . Shaft, brush drive16 023526 1 . Tube, brush drive17 010612 1 . Bearing, complete with locking collar
000153 2 . . Setscrew, hex head, M12 x 35 mm long011077 2 . . Nut, hex, M12 Nyloc005052 1 . . Nipple, grease
18 023534 1 . Hanger, dust skirt011030 3 . . Setscrew, hex head, M10 x 20 mm long011075 3 . . Nut, hex, M10 Nyloc
19 022652 1 . Dust skirt20 023533 1 . . Clamp
011030 5 . . . Setscrew, hex head, M10x 20 mm long011075 5 . . . Nut, hex, M10 Nyloc
*
*
WIDESWEEP ARRANGEMENT - DUAL SWEEP
2
1
3
4
5
6
7
8
91
011
12
13
14
15
16
17
18
19
20
Left
hand
shoc
k a
bso
rber
and
mou
ntin
gb
rack
et o
mitt
ed to
aid
cla
rity
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WIDESWEEP-BRUSH LIFTING ARRANGEMENT1 013855 1 Bracket, hydraulic ram
011011 2 . Setscrew, hex head, M8 x 25 mm long011073 2 . Nut, hex, M8, Nyloc
2 027115 1 . RAM, HYDRAULIC ...............................................................Page J19NI 011629 1 . . Seal kit, ram3 021510 1 . . Bellows4 010067 1 . . Pin, drilled, ram anchoring
011102 2 . . . Washer, 20 mm011122 2 . . . Pin, split, cotter, ” x 1 ” long
5 010067 1 . . Pin, drilled, ram/brush link connecting011102 2 . . . Washer, M20 011122 2 . . . Pin, split, cotter, ” x 1 ” long
6 013853 1 . BRACKET, WIDESWEEP LIFT ..................................................Page C3011011 4 . . Setscrew, hex head, M8 x 25 mm long011073 4 . . Nut, hex, M8, Nyloc
7 014231 1 . . Link, brush lift, RH8 013854 1 . . Link, brush lift, LH
011102 2 . . . Washer, M20 011122 1 . . . Pin, split, cotter, ” x 1 ” long
1
2
3
4
5
6
7
WIDESWEEP-BRUSH LIFTING ARRANGEMENTRH SWEEP ASSEMBLY ILLUSTRATED, LH ASSEMBLY SIMILAR
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
FRONT BRUSH ARRANGEMENT1 013492 1 Pivot block, brush2 013487 1 . Top link, (turnbuckle)3 020564 1 . . Spacer, Ø25 mm O/D x Ø16.5 mm I/D x 14 mm long 4 014129 1 . . Spacer, spring anchor 5 013332 1 . . Bracket, spring anchor
011133 1 . . . Bolt, hex head, M16 x 100 mm long011060 1 . . . Nut, hex, M16, Nyloc
6 020564 1 . . Spacer, Ø25 mm O/D x Ø16.5 mm I/D x 25 mm long7 020565 1 . . Spacer, Ø25 mm O/D x Ø16.5 mm I/D x 22 mm long
011423 1 . . . Bolt, hex head, M16 x 110mm long 011060 1 . . . Nut, hex, M16, Nyloc
8 010248 1 . Tensioner (complete with lock nuts)9 010521 2 . . Spring, 6” long
011077 1 . . . Nut, hex, M12, Nyloc011096 2 . . . Washer, M12, plain
10 013494 1 . Link, brush11 013489 1 . Plate, swivel12 013488 4 . . Bush13 034819 2 . . Sleeve14 010903 1 . . Nipple, grease, ” BSP, straight15 010901 1 . . . Nipple, grease, 135°, ” BSP
011259 2 . . . Bolt, hex head, M12 x 130 mm long011077 2 . . . Nut, hex, M12, Nyloc
16 027116 1 . RAM, HYDRAULIC, COMPLETE ASSEMBLY ........................Page J2117 010067 1 . . Pin, Drilled, Ø20 mm I/D x 50 mm long
011122 2 . . Pin, split, ” x 1 ” long18 010006 1 . MOTOR, HYDRAULIC, DANFOSS OMP 315 ......................Page J17
011069 2 . . Bolt, hex head, M12 x 40 mm long011077 1 . . Nut, hex, M12, Nyloc
19 021214 1 . .Bracket, motor 011075 2 . . . Nut, hex, M10, Nyloc011094 2 . . . Washer, M10, plain
20 024139 1 . Disc, brush, slotted 011011 1 . . Setscrew, hex head, M8 x 25 mm long
21 023469 1 . . . . Brush, polypropylene, Ø400 mm (C/w mounting bolts)000185 6 . . . . . Nut, hex, M8, flanged
NOTES:1. Near-side refers to the side of the vehicle nearest to the kerb. Off-side refers to the side of the vehicle
furthest from the kerb. In most cases the two front brush assemblies are arranged in this configuration regardless of driving position.
2. Components are the same for both assemblies unless stated otherwise, however it should be noted that the nearside and offside assemblies are ‘handed. So that the top link/turnbuckle is always outboard of the ram assembly when the brushes are in the retracted position. From this it can be seen that the illustrated arrangement is from a nearside brush assembly.
1
23
4
5
8
9 10
11
67
12
13
12
13 15
16
17
18
1920
21
14
FRONT BRUSH ARRANGEMENTLH Sweep illustrated
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
FRONT BRUSH SWING-OUT & FIXED ARRANGEMENT1 036009 AS REQ RAM, HYDRAULIC, 13 291/340.............................................Page J212 013497 As req . Link
011030 2 . . Setscrew, hex head, M10 x 20 mm long011094 2 . . Washer, M10, plain
3 014038 As req . . Pin, drilled, Ø20 O/D x 70 mm long011102 As req . . Washer, M20 011122 As req . . Pin, split, Ø ” x 1 ” long
4 013496 As req . Lever, pivot011262 As req . . Bolt, hex head, M8 x 140 mm long011092 As req . . Washer, M8, plain011073 As req . . Nut, hex, M8 Nyloc
5 010067 2 . Pin, drilled, Ø20 mm Dia x 50 mm long6 011122 4 . Pin, split, Ø ” x 1 ” long7 010768 2 . Collar, locking, Ø1” I/D8 010903 2 . Nipple, grease, ” BSP, straight9 013662 4 . Bush, brush pivot
10 013486 2 . Strut, stabilising, gas operated022484 4 . . Joint, ball, stabilising strut011075 2 . . . Nut, hex, M10 Nyloc
11 014904 1 . Link, sliding011030 1 . . Setscrew, hex head, M10 x 20 mm long010313 1 . . Washer, special, Ø40 mm O/D x Ø11 mm I/D x 5 mm long011095 1 . . Washer, spring, M10
FRONT BRUSH SWING-OUT & FIXED ARRANGEMENT
1
2
3
5,6
78
9 4
11
10
VIEWED FROM FRONT OFVEHICLE
DUAL SWEEP SHOWN
LH SWEEP SHOWNRH SWEEP REVERSE IMAGE
5,6
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 10
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
SIDE BRUSH ARRANGEMENT1 013484 1 Pivot, brush, LH
NI 014226 1 Pivot, brush, RH2 013488 4 .
} Pin & bush kit Part No 024610
Bush, brush raise3 013491 2 . Sleeve, brush raise
011259 3 . Bolt, hex head, M12 x 130 mm long011077 3 . Nut, hex, M12 Nyloc
4 010903 1 . Nipple, grease, ” BSP, straight5 013495 1 . . Link, brush raise6 013489 1 . . Plate, swivel7 010901 2 . . . Nipple, grease, 135°, ” BSP 8 020565 1 . Spacer, Ø25 mm O/D x Ø16.5 mm I/D x 22 mm long9 020564 1 . . Spacer, Ø25 mm O/D x Ø16.5 mm I/D x 25 mm long
10 000184 1 . Link, top011133 1 . . Bolt, hex head, M16 x 120 mm long011423 1 . . Bolt, hex head, M16 x 110 mm long011077 2 . . Nut, hex, M16 Nyloc
11 027114 1 . RAM, HYDRAULIC ...............................................................Page J2112 010067 2 . . Pin, Drilled, Ø20 mm I/D x 50 mm long
011122 4 . . Pin, split, Ø ” x 1 ” long011102 2 . . Washer, M20, plain
13 010007 1 . Bracket, brush motor011075 2 . . Nut, hex, M10 Nyloc011094 2 . . Washer, M10, plain
14 010006 1 . . MOTOR, HYDRAULIC ........................................................Page J17011069 2 . . . Setscrew, hex head, M12 x 40mm long011077 2 . . . Nut, hex, M12 Nyloc
15 011688 1 . . . Hub, Brush16 023470 1 . . . . Bush, side, steel17 011011 1 . . . . Setscrew, hex head, M8 x 25 mm long18 010004 1 . . . . Washer, special, Ø45 mm O/D x Ø9 mm I/D x 4 mm long19 010005 1 . . . . Washer, tab
1
2
3 45
6
7
8
9
10
2
4
11
8
12
13 14
15
16
SIDE BRUSH ASSEMBLYLH BRUSH ILLUSTRATED
17,18,19
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 12
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
13 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
SIDE BRUSH SWING-OUT ARRANGEMENT1 013485 1 Bracket, mounting, side brush, LH
NI 014229 1 Bracket, mounting, side brush, RH2 022451* As req . Spacer, Ø20 mm O/D x Ø12.5 mm I/D x 60 mm long
000023 As req . . Bolt, hex head, M10 x 90 mm long2A 014508* As req . Spacer, Ø20 mm O/D x Ø12.5 mm I/D x 24 mm long
011035 As req . . Setscrew, hex head, M10 x 50 mm long3 027156* 4 . Spacer, hex
011031 4 . . Setscrew, hex head, M10 x 25 mm long4 022484 1 . Ball joint, Strut, stabilising
011094 2 . . Washer, M10, plainNI 013486 1 . . Strut, stabilising, gas operated5 027118 1 . RAM, HYDRAULIC ...............................................................Page J216 010067 2 . Pin, drilled, Ø20 mm O/D x 50 mm long
011102 3 . . Washer, M20, plain011122 2 . . Pin, split, Ø ” x 1 ” long
7 010247 1 . Skirt, rubber8 014151 1 . . Clamp, skirt
011011 3 . . . Setscrew, hex head, M8 x 25 mm long011073 3 . . . Nut, hex, M8 Nyloc
9 010768 1 . Collar, Ø1” I/D10 013662 2 . Bush, brush pivot11 010902 1 . Nipple, grease, ” BSP, straight
NOTE: * Dual sweep LH drive. 4 x item 2 per side, 4 x item 3 per side.Dual sweep RH drive. 4 x item 2. LH side, 4 x item 2A. RH side 4 x item 3 per side.LH/RH sweep. 4 x item 3, on the appropriate side.
9
1011
12
3
46
7
8
5
SIDE BRUSH SWING-OUT ARRANGEMENTLH DUAL SWEEP ILLUSTRATED
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 14
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
15 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
SUCTION NOZZLE ARRANGEMENT1 023279 1 Suction nozzle, complete assembly, RH
NI 018207 1 Suction nozzle, complete assembly, LH2 013902 1 . Carrier, nozzle
011054 1 . . Setscrew, hex head, M12 x 45 mm long011077 1 . . Nut, hex, M12, Nyloc
3 013398 1 . Box, suction nozzle000129 4 . . Screw, socket countersunk, M8 x 25 mm long
NI 023154 1 . Rubber suction hoseNI 014303 1 . Suction tube
011073 4 . . Nut, hex, M8, Nyloc4 013360 1 . NOZZLE ASSEMBLY, WATER SPRAY...................................... Page H15 010525 2 . . Chain, nozzle lift, 8 links in length6 010606 1 . . . Carabiner7 013115 2 . Wheel, suction nozzle
011105 1 . . . Bolt, hex head, M12 x 120 mm long011096 3 . . . Washer, M12, plain011077 1 . . . Nut, hex, M12, Nyloc
8 013903 1 . Frame, nozzle tilt9 011592 1 . . Clamp, nozzle flap (rear)
011011 4 . . . Setscrew, hex head, M8 x 25 mm long10 013615 2 . . Clamp, nozzle flap (side)
011011 2 . . . Setscrew, hex head, M8 x 25 mm long11 011593 1 set . Nozzle flap, rubber (comprising 1 front, 1 rear, 2 side)12 011592 1 . . Clamp, nozzle flap (front)
011073 4 . . .Nut, hex, M8, Nyloc13 011811 1 . Rod, nozzle tilt
011092 1 . . Washer, M8, plainattaching rod to nozzle tilt frame}
011072 2 . . Nut, hex, M8011073 1 . . Nut, hex, M8, Nyloc 011042 1 . . Bolt, hex head, M10 x 110 mm Long } anchor top of rod
and top of spring011094 4 . . Washer, M10, plain011075 1 . . Nut, hex, M10, Nyloc
14 027113 1 . RAM .................................................................................Page J19NI 011629 1 . . Seal, ram, repair kit
011036 2 . . Bolt, hex head, M10 x 60 mm long011075 2 . . Nut, hex, M10, Nyloc
15 010521 1 . Spring, coil, nozzle tilt011038 1 . . Bolt, hex head, M10 x 80 mm long011094 13 . . Washer, M10, plain (to space-out between carrier & spring)
SUCTION NOZZLE ARRANGEMENT
2
3
4
5,6
7
89
10
11
12
13
1
14
13
15
Part of item 2. Ref only
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 16
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
17 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
- SUCTION NOZZLE LIFTING ARRANGEMENT1 027119 1 RAM, HYDRAULIC..................................................................Page J19
NI 011629 1 . Seal kit, ram2 013904 1 . Bracket, pulley, LH
NI 014224 1 . Bracket, pulley, RHNI 023844 1 . Bracket, pulley, LH (dual sweep vehicles only)
011011 4 . . Setscrew, hex head, M8 x 25 mm long011073 4 . . Nut, hex, M8, Nyloc
3 010709 1 . . Pulley (C/W Bush) ∅3” (76.2 mm) 011035 2 . . . Setscrew, hex head, M10 x 50 mm long011075 2 . . . Nut, hex, M10 Nyloc
4 010248 1 . . Tensioner (C/W nuts & washers)011096 1 . . . Washer, M12, plain011077 1 . . . Nut, ex, M12, Nyloc
5 031379 1 . . Cable, one-piece, steel with fabric core, ∅6 mm
Item Part Number Quantity Description
STANDARD WANDER-HOSE ASSEMBLY1 012488 1 Spigot (Mounts to Antiluce Fasteners on Door/Cat-Flaps))2 013537 1 . Gasket3 010119 3 m . Hose, flexible
010519 2 . . Clamp, worm drive, 135 - 165 mm4 010587 1 . Pipe, nozzle5 010321 1 . . Handle, wander hose
010509 2 . . . Clip, toggle021841 2 . . . Hook, toggle clip
6 010245 4 . . . Hooks
23
4 3
5
SUCTION-NOZZLE LIFTING ARRANGEMENT
STANDARD WANDER-HOSE ASSEMBLY
1,2
3
4 5
Rear Door (Ref. Only)
6
1
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 18
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
19 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
OVERHEAD SUCTION BOOM ARRANGEMENT1 027126 1 Support elbow2 011808 1 . Clip3 010746 1 Cover, elbow4 011079 2 . Wing nut5 035693 2 Fixing tab6 035696 1 Housing6 035697 1 Housing (Hi-Tip)7 028448 1 Aluminium suction Tube 1560 mm Long8 023493 1 . Strap, suction tube9 010950 1 Hose ” black
10 010516 2 . Clamp, worm drive, 11 - 16 mm11 010922 1 . Hose tail, ” BSP x ” hose12 010928 1 . Back nut, ” BSP13 011169 1 . Elbow, swivel, “ BSP14 010112 1 . Nozzle15 012926 1 . Spray jet, LF6-8016 027125 1 Suction elbow17 012253 2 . Antiluce, (small)18 021944 2 . Double wound Grip ‘R’ Clip19 020711 1 . Leash cable20 013577 1 . Swivel spring hook21 012486 1 . Cap plate22 023599 1 . Ring pull23 010526 1 . Chain
OVERHEAD BOOM ARRANGEMENT
1 2
2
3,4
5
6
7 8 9 10 11 12 13,14,15
16
17,1819
2021
22
23
ILLUSTRATED PARTS CATALOGUE Section FSCARAB VM MINOR - CANbus Page 20
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Sweeping & Suction Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
F
F Section ILLUSTRATED PARTS CATALOGUE
21 Page SCARAB VM MINOR - CANbus
Sweeping & Suction Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION GHOPPER & RELATED COMPONENTS
TABLE OF CONTENTS
Assembly/Description Page
Hopper general arrangement (includes impellor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Hopper rear and rear door arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Internal hopper components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Fan assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Auto blanking assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Standard wander-hose assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Wander hose manual blanking assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Overhead suction boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Hi-Tip hopper assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Hydraulically operated rear door components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
NOTE:Unless stated all parts are common for EURO 4 and 5 models
G Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HOPPER - GENERAL ARRANGEMENT (includes Impellor)1 025415 1 Hopper complete assembly2 034590 1 . Extension panel LH
NI 034756 1 . Extension panel RH3 025077 1 . Fan plate
4 011075 8 . Nut, M10 Nyloc5 011424 1 . Washer large M10, plain6 025240 1 . Impellor7 025564 1 . ASSEMBLY MOTOR VOAC.................................................. Page G58 024790 1 . Inlet cone9 021526 1 . Cat flap door LH
10 021525 1 . Cat flap door RH
Per door
000261 2 . . Bolt, hex head, M8 x 55 mm long st stL
000263 1 . . Nut, hex, M8 Nyloc st st11 013599 1 . . Seal, side-loading door12 021523 1 . . Handle, side-loading door
000257 2 . . . Setscrew, hex head, M8 x 25 mm long st stL
000264 2 . . . Washer, M8, plain st stL
000263 1 . . . Nut, hex, M8 Nyloc st stL
13 031601 1 . . Catch bracket000252 2 . . . Setscrew, hex head, M6 x 20 mm long st stL
000254 2 . . . Washer, M6, plain st stL
000253 2 . . . Nut, M6 Nyloc st stL
14 013702 1 . . Antiluce large15 012486 1 . . Cap plate
025222 0.5 metre . . Titanfast DX7816 020711 1 . . Leash cable
000258 1 . . . Setscrew, hex head, M8 x 30 mm long st stL
000262 2 . . . Nut, hex, M8 st stL
000263 2 . . . Nut, hex, M8 Nyloc st stL
17 012253 4 . . . Antiluce NI 025436 1 . Capping LH18 025437 1 . Capping RH19 013594 As req . Seal, front aperture20 011877 1 . Hopper safety prop21 011787 1 . PROP POCKET ......................................................................Page C122 011577 1 . Hopper lift Ram (standard)NI 012203 1 . . Seal kit for hopper ram 011577NI 026720 1 . Hopper llft ram (Hi Tip 1.3)NI 026719 2 . Hopper lift ram (Hi Tip 1.6)23 011640 1 . Hinge pin (hopper lift)
011013 2 . Setscrew, hex head, M8 x 35 mm long011073 2 . Nut, hex, M8 nyloc
24 033210 1 . Hopper sensor stop011043 1 . . Bolt, hex head, M10 x 70 mm long011074 2 . . Washer, M10, plain011075 1 . . Nut, hex, M10 Nyloc
NOTE: FOR REAR DOOR AND REAR COMPONENTS PLEASE SEE PAGE G3
1
9,10,11
3,4,5 7
8
15,16,17
18
12,13,14
6
HOPPER GENERAL ARRANGEMENT
19
20
21
22
23
24
2
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HOPPER REAR & REAR DOOR ARRANGEMENT1 014736 1 Rear door2 025262 2 . Hinge
NI 010544 1 . . Seal, rear door3 027923 2 . Cover plate4 000248 4 . . Plastic hand screw
NI 027924 1 . . Fan protection coverNI 010502 1 . . Pull handle for coverNI 000248 2 . . Plastic hand-screw5 010245 4 . Hook for wander hose
000259 8 . . Bolt, hex, M8 x 60mm long st stL
000258 8 . . Nut, hex, M8 Nyloc st stL
6 032181 2 . Door rib protector7 010304 1 Beacon8 010297 1 . Bracket, beacon
011011 2 . Setscrew, hex head, M8 x 25 mm long011073 2 . Nut, hex, M8 Nyloc030952 2 . Lens cover (spares)????? As Req . Bulb (spare) 12 Volt x 21 Watt
9 014995 1 Handle rear, door locking10 014997 1 . Plastic handle grip11 014996 1 . Locking bar
010077 4 . Locking clamps012427 5 . Roll Pin
12 010232 1 . Pin, chain & bracket13 012486 1 Blanking plate, rear door
000263 1 . Nut, hex, M8 full st stL
000263 1 . Nut, hex, M8 Nyloc st stL
14 012253 4 . Antiluce clips021979 2 . . Rubber washer
15 020711 1 . Leash Cable000258 1 . . Setscrew, hex head, M8 x 30 mm long st stL
000263 1 . . Nut, hex, M8 full st stL
000263 1 . . Nut, hex, M8 Nyloc st stL
16 010955 1 Hose, drain012927 1 . Jubilee clip
17 028023 1 Cover, hopper GRPNI 013952 4.50 . Seal (goes between hopper cover and hopper top)NI 025680 5 . Retaining clipNI 010509 5 . Fastener with hinge
000286 10 . . Screw, slotted countersunk, M6 x 20 mm long011090 10 . . Washer, M6, plain011071 10 . . Nut, hex, M6 Nyloc
18 020521 1 Gas springNI 036477 1 Gas spring (1. 3/ 1. 6 hi-tip after June 2009)19 024147 1 Rear bumper20 031244 1 Rubber Flap (fuel filler dual sweep machines)21 020523 1 Prop, rear door22 034682 1 Handle, bracket23 034683 1 . Handle24 022816 1 . Locking bar
NOTE: For Wander Hose assembly 015033 please turn to Page G9
HOPPER REAR & REAR DOOR ARRANGEMENT
3,4
5
1
6
10
11
9
12
13
2
16
17
18
21
14
18
20
19
22
23
7
8
15
24
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
INTERNAL HOPPER COMPONENTS1 025261 1 Screen1 025668 1 Screen, fine mesh type (dual sweep machines)2 025245 3 . Gudgeon pin3 013506 3 . Pin4 013507 3 . Linch pin
NI 027744 1 . Handle, screen rear 5 025529 As req Inlet tube5 034235 As req Inlet tube, PU COATED
000329 13 . Screw, socket button head, M8 x 20 mm long st stL, per tube000263 13 . Nut, hex, M8 Nyloc st stL, per tube
NI 028822 1 Deflector, LH (single sweep)NI 035586 1 Deflector, LH (single sweep), PU COATED6 028823 1 Deflector, RH (single sweep)6 035587 1 Deflector, RH (single sweep), PU COATED
NI 025533 1 Deflector, LH (dual sweep)NI 034240 1 Deflector, LH (dual sweep), PU COATED6 025534 1 Deflector, RH (dual sweep)6 034241 1 Deflector, RH (dual sweep), PU COATED
014587 1 Blanking plate000329 12 . Screw, socket button head, M8 x 20 mm long st stL, per tube000263 12 . Nut, hex, M8 Nyloc st stL, per tube
Item Part Number Quantity Description
FAN ASSEMBLY1 025077 1 Fan plate2 025240 1 . Impellor3 024790 1 Inlet cone4 025564 1 . Fan motor assembly5 024641 1 . Motor, fan
NI 027237 1 . . Seal Kit, for 024641 Voac fan motor NI 024791 1 . . . Washer, Voac motorNI 011052 1 . . . Setscrew, hex head, M12 x 30 mm longNI 025390 1 . Valve block, Voac motorNI 002101 1 . . O-Ring, (base of Voac motor)NI 011156 1 . . Seal, Dowty (for plug)NI 000048 8 . . Screw, socket cap head, M10 x 80 mm LongNI 011095 8 . Washer, M10, spring NI 011155 2 . Seal, Dowty, ” BSPNI 011247 1 . Seal, Dowty, M18NI 011248 1 . Adaptor, M18 x ” BSPNI 011172 1 . Elbow, swivel, ” BSPNI 010921 1 . Hose Stem x ” BSPNI 010928 1 . Nut, brass ” BSPNI 011161 2 . Adaptor, ” BSPNI 002076 1 . Plug M12 x 1“NI 025184 1 Speed sensor leadNI 004226 1 . PlugNI 004227 1 . SealNI 004228 1 . SealNI 014157 1 Hose ” x 4350 mm - fan returnNI 001070 1 Hose ” x 2230 mm - fan feedNi 013514 1 Fan scraper
1 6
5
INTERNAL HOPPER COMPONENTS
2 3,4
1
2
4,5
SUCTION FAN ASSEMBLY
3
8
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
AUTO-BLANKING MAIN ASSEMBLY1 025531 1 Mounting plate, LH
NI 025532 1 Mounting plate, RH
}}
per plate
per deflector
000257 5 . Setscrew, hex head, M8 x 25 mm long st stL
000263 5 . Nut, M8 st stL
000264 5 . Washer, M8, plain st stL
000273 1 . Setscrew, hex head, M12 x 25 mm long st stL
000277 1 . Washer, M12, plain st stL
000275 1 . Nut, hex, M12 Nyloc st stL
NI 013488 4 . Bush2 025530 2 . Flap2 034237 2 . Flap, PU COATED3 025526 1 . . Flap arm, LH4 025527 1 . . Flap arm, RH5 028822 1 . Deflector, LH6 028823 1 . Deflector, RH
011051 4 . . Setscrew, hex head, M12 x 25 mm long011076 4 . . Nut, hex, M12 Nyloc011096 16 . . Washer, M12, plain
7 022350 2 . Ram011122 2 . . Split pin011135 2 . . Washer, M16, plain
8 014469 2 . Clevis M129 025528 2 . Lever
000211 2 . . Nut M12 x 1. 25011031 2 . . Setscrew, hex head, M10 x 25 mm long
10 010991 2 . Hose, rubber, ” BSP x 550 mm long11 010981 2 . Hose, rubber, ” BSP x 711 mm long12 NA 2 . INLET TUBE .............................................................................Page G513 NA 1 VALVE, CONTROL, HYDRAULIC (dual sweep shown).......Page J27
011010 2 . Setscrew, hex head, M8 x 20 mm long011073 2 . Nut, hex, M8 Nyloc
14 001147 1 . Hose, rubber, ” BSP x 500 mm long, 90° ends15 001107 2 . Hose, rubber, ” BSP x 1300 mm long, straight + 90° ends15 010987 2 . Hose, rubber, ” BSP x 1660 mm long, straight + 90°ends (1.3 Hi-Tip)16 001101 2 . Hose, rubber, ” BSP x 1125 mm long, straight + 90° ends16 001106 2 . Hose, rubber, ” BSP x 1820 mm long, straight + 90° ends (1.3 Hi-Tip)17 001106 1 . Hose, rubber, ” BSP x 1820 mm long, straight + 90° ends18 001148 1 . Hose, rubber, ” BSP x 400 mm long, 90° ends19 010958 As req . Pipe, rubber, ” bore20 010516 1 . Clamp, worm drive, 11 - 16 mm
1
2,4
5
6
2,3 12
AUTO BLANKING ASSEMBLY
9
7 8
1011
Left hand ram assembly illustrated. Right hand assembly is similar but mounting plate alignment reversed.
13
14
15
16
17
18
19,20
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
STANDARD WANDER-HOSE ASSEMBLY1 012488 1 Spigot (mounts to Antiluce fasteners on door/cat-flaps))2 013537 1 . Gasket
3 010119 3 m . Hose, flexible010519 2 . . Clamp, worm drive, 135 - 165 mm
4 010587 1 . Pipe, nozzle5 010321 1 . . Handle, wander hose
010509 2 . . . Clip, toggle021841 2 . . . Hook, toggle clip
6 010245 4 . . . Hooks011017 8 . Bolt, hex head, M8 x 60 mm long
NI 032181 4 . . . . Door rib protect
Item Part Number Quantity Description
WANDER HOSE MANUAL BLANKING ASSEMBLY1 026819 1 Spigot, wander hose2 026818 1 Blanking flap3 026817 2 Gasket spacer strip4 013507 1 Pin & chain
1,2
3
4 5
Rear Door (Ref. Only)
6
STANDARD WANDER-HOSE ASSEMBLY
1
3
2
4
WANDER HOSE MANUAL BLANKING ASSEMBLY
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 10
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
OVERHEAD SUCTION BOOM ARRANGEMENT1 027126 1 Support elbow2 011808 1 . Clip3 010746 1 Cover, elbow4 011079 2 . Wing nut5 035693 2 Fixing tab6 035696 1 Housing6 035697 1 Housing (Hi-Tip)7 028448 1 Aluminium suction Tube 1560 mm Long8 023493 1 . Strap, suction tube9 010950 1 Hose ” black
10 010516 2 . Clamp, worm drive, 11 - 16 mm11 010922 1 . Hose tail, ” BSP x ” hose12 010928 1 . Back nut, ” BSP13 011169 1 . Elbow, swivel, “ BSP14 010112 1 . Nozzle15 012926 1 . Spray jet, LF6-8016 027125 1 Suction elbow17 012253 2 . Antiluce, (small)18 021944 2 . Double wound grip ‘R’ clip19 020711 1 . Leash cable20 013577 1 . Swivel spring hook21 012486 1 . Cap plate22 023599 1 . Ring-pull23 010526 1 . Chain
OVERHEAD BOOM ARRANGEMENT
1 2
2
3,4
5
6
7 8 9 10 11 12 13,14,15
16
17,1819
2021
22
23
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 12
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
13 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HI-TIP HOPPER ASSEMBLY1 025643 1 Hopper2 026720 2 . HOPPER LIFT RAM (H I-TIP 1. 3) ...........................................Page J232 026719 2 . HOPPER LIFT RAM (H I-TIP 1. 6) ...........................................Page J233 011952 1 . Top link (Hi -Tip 1. 3)3 020112 1 . Top link (Hi -Tip 1. 6)4 023495 2 . Link (Hi -Tip 1. 3)4 020231 1 . Link (Hi -Tip 1. 6)5 014709 1 . Sub frame (Hi -Tip 1. 3)5 020056 1 . Sub frame (Hi -Tip 1. 6)
011031 10 . . Setscrew, hex head, M10 x 25 mm long011075 10 . . Nut, hex, M10 Nyloc
6 014722 2 . Trunnion plate LH7 014721 2 . Trunnion plate RH
011031 7 . . Setscrew, hex head, M10 x 25 mm long011032 4 . . Setscrew, hex head, M10 x 20 mm long
8 014723 1 . Rear support Bracket011032 4 . . Setscrew, hex head, M8 x 30 mm long011075 4 . . Nut, hex, M10 Nyloc
9 020113 2 . Outrigger (Hi -Tip 1. 6)10 011974 2 . . Outrigger Leg (Hi -Tip 1. 6)
000184 2 . . . Bolt, hex head, M16 x 120 mm long011060 2 . . . Nut, hex, M16 Nyloc011031 2 . . . Setscrew, hex head, M8 x 35 mm long011075 2 . . . Nut, hex, M8 Nyloc
11 013138 2 . Link pin (Hi -Tip 1. 6)12 Contact Spares 2 . Linch pin & chain13 Contact Spares 2 . Fixing chain14 034562 1 . Rear chute assembly
1
2
3
4
5
7
8
6
14
REAR CHUTE
HI-TIP ASSEMBLY
OUTRIGGER
11
9
10
12
13
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 14
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
15 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HYDRAULICALLY OPERATED REAR DOOR ARRANGEMENT1 022511 1 RAM, HYDRAULIC..................................................................Page J232 030539 1 . Support, ram
NI 033273 1 . Support, ram (low height variants only)000257 6 . . Setscrew, hex head, M8 x 25 mm, st stL
000262 6 . . Nut, hex, M8 Nyloc, st stL
3 014038 1 . Pin, swivel, ∅20 mm x 70 mm long011122 2 . . Pin, split, ” x 1 ” long011102 As req . . Washer, M20, plain
4 014038 1 . Pin, swivel, ∅20 mm x 90 mm long011122 2 . . Pin, split, ” x 1 ” long011102 As req . . Washer, M20, plain
5 030540 1 . Plate, ram000257 5 . . Setscrew, hex head, M8 x 25 mm long st stL
000262 5 . . Nut, hex, M8 Nyloc, st stL
6 011317 2 . Hose, rubber, ” BSP x 295 mm long, (straight ends)7 011269 2 . . Adaptor, bulkhead, ” BSP, M/M8 001106 2 . Hose, rubber, ” BSP x 1820 mm long, (straight + 90° end)9 011187 2 . . Elbow, ” BSP, M/M
10 001037 2 . Hose, rubber, ” BSP x 2650 mm long, (straight + 90° end)11 030544 2 . Stiffener, vertical12 030545 1 . Stiffener, horizontal
000257 5 . . Setscrew, hex head, M8 x 25 mm long st stL
000262 5 . . Nut, hex, M8 Nyloc, st stL
13 012582 1 VALVE, SOLENOID CHECK ...................................................Page J2514 023569 1 VALVE, CONTROL .................................................................Page J2515 010958 As req . Pipe, rubber, ” bore16 010516 2 . . Clamp, worm drive, size, 11 - 16 mm17 025599 1 . VALVE, FLOW & PRESSURE .................................................Page J2518 010987 1 . . Hose, rubber, ” BSP x 1660 mm long, (straight ends)19 011000 As req . . Pipe, rubber, ” bore20 010517 2 . . . Clamp, worm drive, 18 - 25 mm21 025440 1 Switch box, remote, hopper/rear door operation22 030546 1 . Bracket switch box support
23
4
5
67
8
8
910
1112
13
14
15,16
17 18 19,20
21
22
1
ILLUSTRATED PARTS CATALOGUE Section GSCARAB VM MINOR - CANbus Page 16
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Hopper & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
G
G Section ILLUSTRATED PARTS CATALOGUE
17 Page SCARAB VM MINOR - CANbus
Hopper & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION HWASHING & DUST SUPPRESSION SYSTEM
Table of Contents
Assembly/Description Page
Water tank arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Hydrant filler kit & mounting items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Electric water pump assembly (low pressure). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Water valves (Airtechnics up to July 2008) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Water valves (Cotswold from July 2008) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Low pressure water pump assembly - EURO 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Water valve arrangment - EURO 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Water filter assembly (low pressure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Low pressure spray bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Jets - low pressure front/side brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Jets - fixed low pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11High-pressure water pump arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13High-pressure (21 litres/minute) water pump components . . . . . . . . . . . . . . . . . . . . . . . .15Standard hose arrangement & detergent feed valve (hand lance) . . . . . . . . . . . . . . .17Fan wash assist arrangement, detergent bottle & feed valve (water boom . . . . . . . . .19High-pressure spray system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Hose reel component parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Water filter assembly (high-pressure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Water boom arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23High-pressure spray bar assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Adjustable spray Bar mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
NOTE:Unless stated all parts are common to both EURO 4 and EURO 5 models
H Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
item Part Number Quantity Description
WATER TANK ARRANGEMENT1 014678 1 Water tank2 014040 1 . Hydrant filler assembly
000254 4 . . Washer, M6, plain st stL
000253 4 . . Nut, hex, M6 Nyloc st stL
3 013661 1 . . Cap, fillerNI 020896 1 . Disc, rubber (located centrally on top face of tank)
011115 4 . . Screw, Posidrive, self-tapping, No. 10 x ” long4
}per tube
014303 As req . Suction tube000256 6 . . Setscrew, hex head, M8 x 20 mm long st stL
000329 2 . . Screw, socket button head, M8 x 20 mm long st stL
000270 8 . . Washer, M8, plain st stL
5 010951 0.5 metre . . Hose, PVC clear, ” boreNI 010964 2 . . . O-Clips ”6 010912 2 . . . Elbow, galvanised, ” BSP, M/M
NI 010922 2 . . . Hose tail, ” BSP x ”7 023154 1 . . Suction hose
012932 2 . . . Clamp, worm drive, 135 - 165 mm8
}per bracket
014278 1 . Bracket tank base , LH9 014279 1 . Bracket tank base , RH
011073 3 . . Nut, hex, M8 nyloc011055 1 . . Bolt, hex head, M12 x 65 mm long011096 2 . . Washer, M12, plain011077 1 . . Nut, hex, M12 Nyloc011092 3 . . Washer M8, plain
10 013462 2 . Bracket, rubber buffer mounting 011051 4 . . Setscrew, hex head, M12 x 25 mm long011077 4 . . Nut, hex,M12 nyloc
11 014693 2 . Rubber buffer011034 4 . . Setscrew, hex head, M10 x 40 mm long011075 4 . . Nut, hex, M10 Nyloc011094 4 . . Washer M10, plain
12 030597 1 FILTER ASSEMBLY, WATER....................................................... Page H913 011161 3 . Adaptor, ” BSP, M/M
011155 3 . Seal, dowty, ” BSP14 011168 1 . Adaptor, ” BSP, M/M15 002149 1 . Blanking cap, ” BSP16 002011 1 . Blanking cap, ” BSP17 034342 3 Water spray nozzle
011001 3 . Setscrew, hex head, M6 x 16 mm long011091 3 . Washer, M6, spring
18 014679 2 . Tee, plastic, 6 mm tube, push fitNI 035733 As req . . Tube, plastic, 6 mm (blue)
WATER TANK ARRANGEMENT
1
7
89
10,11
12,13
14,15
13,16
17
18
Item 16 replaced with high pressure water filter (Page H21), when high pressure pump is fitted
2,3
4
5
6
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HYDRANT FILLER KIT & MOUNTING ITEMS1 020484 2 Bracket, standpipe mounting
NI 036248* 1 . Locking plate (to enable fitment of padlock to secure item 3)011010 4 . Bolt, hex, M8 x 20 mm long011073 5 . Nut, Hex, M8
2 020483 2 . Strap, Standpipe mounting000021 2 . . Bolt, hex, M6 x 40 mm long011071 2 . . Nut, hex, M6 Nyloc
3 010509 2 . Catch011002 4 . . Screw M6 x 16 mm long011071 2 . . Nut, hex, M6 Nyloc
4 014547 1 Hydrant hose5 013171 1 . Hydrant hosetail6 014546 1 . Hydrant male Insert7 014544 1 Hydrant standpipe8 014545 1 Hydrant key & bar9 013840 1 Filler cap assembly
10 013169 1 . Hydrant thread adaptor11 010918 1 . . Elbow, galvanised, ”BSP, M/F
011104 1 . . Washer, 1”, plain
NOTE:* Optional if lockable stowage is required
HYDRANT MOUNTING PARTS & MOUNTING ITEMS
1
2
4
6
5
8
7
3
9
11
10
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WATER PUMP, LOWER PRESSURE, 12 Volt1 026866 1 Electric water pump
011001 4 . Setscrew, hex head, M6 x 20 mm long011090 8 . Washer, M6, plain011071 4 . Nut, hex, M6 Nyloc
2 001015 As req . Hose, rubber 12 mm bore (to water valves)010516 2 . Hose clamp, worm drive, 11 - 16 mm
3 026723 1 . Elbow (delivery)4 028176 1 . Blanking flange5 026723 1 . Elbow (suction)6 002108 As req . Hose, plastic reinforced, ” bore (from water tank)
010518 2 . Jubilee clip 1X7 031510 1 . Tee, plastic8 010959 As req . Hose, rubber ” bore (pressure relief return)
010518 2 . Hose clamp, worm drive, 30 - 40 mmNA 026891 1 . Diaphragm replacement kitNA 026892 1 . Valve replacement kit
Item Part Number Quantity Description
WATER VALVE ARRANGEMENT (Cotswold)1 034637 1 Water valve 12 Volt, 3 way (complete)
NI 034639 1 Water valve 12 Volt, 4 way (complete)NI 036342 1 Water valve 12 Volt, 5 way (complete)NI 034625 1 Water valve 12 Volt, 1 way (complete)NI 033364 1 . Mounting bracket
011001 2 . . Setscrew, hex head, M6 x 16 mm long011071 2 . . Nut, hex, M6 Nyloc000052 2 . . Setscrew, hex head, M5 x 16 mm long
2 034627 As req . Solenoid, 12 Volt3 034626 As req . Coil, 12 Volt, 8 Watts4 011159 1 . Adaptor, ” BSP, M/M5 011205 1 . Elbow, ” BSP, M/F
011153 1 . . Seal, dowty, ”6 011205 1 . Tee, ” BSP, F/F/F7 010914 1 . Adaptor, ” x ” BSP, M/M8 030741 1 . Pressure regulating valve9 025181 1 . Hose tail, ” BSP x ” hose
10 026869 1 . Hose tail, ” BSP x ” hose002108 As req . Hose, plastic reinforced, ” bore010518 2 . Clamp, worm drive, 30 - 40 mm
11 024646 As req . Elbow, “ BSP male x 6 mm tube, push fitNI 035733 As req . . Plastic tube, 6 mm (blue)NI 034624 As req . Diaphragm replacement kit
Item Part Number Quantity Description
WATER VALVE ARRANGEMENT (Airtechnics))1 031705 1 Water valve 12 Volt, 3 way (complete)
NI 031706 1 Water valve 12 Volt, 4 way (complete)NI 031707 1 Water valve 12 Volt, 5 way (complete)2 030737 1 . 3-way manifold
NI 030737 1 . 4-way manifoldNI 030738 1 . 5-way manifold3 030745 As req . Manifold bolt
03087 As req . . Seal, O-ring 4 030739 As req . Solenoid, water valve, 12 Volt5 030742 As req . Coil, 12 Volt
NI 030744 As req . Repair kit
ELECTRIC LOW PRESSURE WATER PUMP
WATER SOLENOID VALVE ARRANGEMENT3 Way shown
1234
7
1
23
4
5
6
3
8
910
11
6
58
8
1
2 34
5
AIRTECHNICS
COTSWOLD
ALL PARTS AS COTSWOLD
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
LOWER PRESSURE WATER PUMP ASSEMBLY - EURO 51 037160 1 Water services hanger plate ..............................................Page C 72 037161 1 . Bracket, water services, hanger plate, rear
011075 4 . . Nut, hex, M8 nyloc3 037162 1 . Bracket, water services, hanger plate, front
011075 4 . . Nut, hex, M8 nyloc4 026866 1 . Electric water pump
011001 4 . . Setscrew, hex head, M6 x 20 mm long011090 4 . . Washer, M6, plain
NI 026723 1 . . Elbow (suction)NI 002108 As req . . Hose, plastic reinforced, ” bore 5 031510 1 . . Tee, plastic
NI 010518 4 . . . Clamp, worm drive, 30 - 406 026723 1 . . Elbow (delivery)
NI 001015 As req . . Hose, rubber 12 mm bore NI 010516 2 . . . Clamp, worm drive, 11 - 16 NI 028176 1 . Blanking flange
NA 026891 1 . Diaphragm replacement kitNA 026892 1 . Valve replacement kit
Item Part Number Quantity Description
WATER VALVE ARRANGEMENT - EURO 51 034637 1 Water valve 12 Volt, 3 way (complete, less fittings)
NI 034639 1 Water valve 12 Volt, 4 way (complete, less fittings)NI 036342 1 Water valve 12 Volt, 5 way (complete, less fittings)NI 034625 1 Water valve 12 Volt, 1 way (complete, less fittings)
000052 4 . . Setscrew, hex head, M5 x 16 mm long2 034627 As req . Solenoid, 12 Volt3 034626 As req . Coil, 12 Volt, 8 Watts4 011159 2 . Adaptor, ” BSP, M/M
011153 2 . . Seal, dowty, ” 5 011205 1 . Elbow, ” BSP, F/F6 010914 1 . Adaptor, ” x ” BSP, F/F7 011172 1 . Elbow, ” BSP, M/F8 026869 1 . Hose tail, ” BSP x ” hose9 010914 1 . Adaptor, ” x ” BSP, M/M
10 030741 1 . Pressure regulating valve11 025181 1 . Hose tail, ” BSP x ” hose12 024646 As req . Elbow, “ BSP male x 6 mm tube, push fitNI 035733 As req . . Plastic tube, 6 mm (blue)NI 034624 As req . Diaphragm replacement kit
1
2 34
5
6
1
4,5
2 3
6
7
8
4,5
6
9
101112
LOW PRESSURE WATER PUMP ASSEMBLY - EURO 5
WATER VALVE ARRANGEMENT - EURO 5
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WATER FILTER ASSEMBLY - LOW PRESSURENA 030597 1 Filter, complete
1 010121 1 Filter2 025181 1 Hosetail, ” BSP to ” hose3 010962 1 Reducing bush ” to ” BSP, M/F4 011174 1 . Elbow, swivel, ” BSP, M/F
Item Part Number Quantity Description
LOW PRESSURE SPRAY BAR ASSEMBLY1 030203 1 Spray bar, plastic (complete)2 030634 3 . Nozzle holder3 030636 3 . Washer, rubber4 030633 3 . Filter 5 030637 3 . Spray jet (red)6 031418 3 . Nozzle cap7 031338 2 . Clamp8 031995 1 . Adaptor, “ BSP female x 6 mm tube, push fit
NI 035773 As req . Tube, plastic, 6 mm (blue)9 028761 1 . CARRIER.............................................................................. Page H13
011031 4 . . Setscrew, hex head, M10 x 25 mm long011075 4 . . Nut, hex, M10 Nyloc
LOW PRESSURE WATER SPRAY BAR ASSY
1
4 2,3
WATER FILTER ASSEMBLY
1
2
3
4
5
6
7
8
9
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 10
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WATER SPRAY JET, LOW PRESSURE - FRONT & SIDE BRUSH1 031995 1 . Adaptor, ” BSP female x 6 mm tube, push fit2 030661 1 . Nozzle mount - Side brush only
NI 1 . Nozzle mount - Front brush only3 010922 1 . Hose tail, ”BSP male X ” tube4 030663 1 . Hose, rubber, ” X 120 mm long5 030747 1 . Elbow, nozzle6 030636 1 . Washer, rubber7 030748 1 . Spray jet (blue)8 030746 1 . Nozzle cap9 030633 1 . Filter
10 031072 1 . O-Clip 15/18NI 033433 1 . . Valve, Ball
Item Part Number Quantity Description
USED ON MACHINES UP TO MID 2008WATER SPRAY JET, LOW PRESSURE - FIXED TYPE
1 031995 1 Adaptor, ” BSP female x 6 mm tube, push fit2 030892 1 Bracket, Spray nozzle (Fixed)3 030769 1 Nozzle body straight4 030636 1 Washer rubber5 030633 1 Filter6 030748 1 Spray jet7 030746 1 Nozzle cap
Item Part Number Quantity Description
USED ON MACHINES FROM MID 2008WATER SPRAY JET, LOW PRESSURE - FIXED TYPE
1 023203 1 Elbow, ” BSP male x 6 mm tube, push fit2 030892 1 Bracket, spray nozzle (fixed)3 033433 1 Valve, ball, ” BSP4 030769 1 Nozzle body, straight5 030636 1 Washer rubber6 030633 1 Filter7 030748 1 Spray jet8 030746 1 Nozzle cap
WATER SPRAY JET - FIXED TYPE
FRONT / SIDE BRUSH SPRAY JET
1
2
3
4
5
6
7
1
2
3
4
5
6
9
7
8
10
1
2
3
4
5
6
7
8
UP TO MID 2008 FROM MID 2008
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 12
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
13 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HIGH-PRESSURE PUMP ARRANGEMENT1 028761 1 Carrier2 014449 1 . Motor bracket3 021315 1 . MOTOR HYDRAULIC 15 CC, 1MR015 ............................... Page A154 014867 1 . Pump, High-pressure RK21.15HN
000136 8 . . Screw, socket cap head, M8 x 16 mm long011068 4 . . Setscrew, hex head, M6 x 35 mm long011090 4 . . Washer, M6, plain011071 4 . . Nut, hex, M6 Nyloc
5 034308 1 . High pressure spray bar hose6 011199 1 . Adaptor, ” BSP, M/M7 011152 1 . . Seal, Dowty, ”8 011257 1 . Valve, ball, “ BSP9 011199 3 . Adaptor, ” x ” BSP, M/M
10 011223 1 . Tee, swivel, ” BSP, M/M/F11 011205 2 . Elbow, swivel, ” BSP, F/F12 011159 2 . Adaptor, ” BSP, M/M13 011153 1 . . Seal, Dowty, ” BSP14 010599 1 . Valve, unloader15 002008 1 . Adaptor, bulkhead, ” BSP, M/M16 011135 1 . . Washer, M16, plain17 010930 2 . Hosetail, ” BSP x ” tube18 011743 1 . Valve, ball, ” BSP19 010910 2 . Elbow, ” BSP glavanised, M/F20 011269 2 . Adaptor, bulkhead, ” BSP, M/M21 014455 1 . Drive belt cover
011090 2 . . Washer, M6, plain011071 2 . . Nut, hex, M6 Nyloc
22 001121 1 . Hose, rubber, ” BSP x 270 mm long, straight end + 90°23 025599 1 . POWER STEERING REGULATOR VALVE............................. Page A1524 010959 1 . Tube, rubber, 1” bore
010518 2 . . Clamp, worm drive, 30 - 40 mm25 001148 1 . Hose rubber, ” BSP x 400 mm long, 90° ends26 011000 1 . Tube, rubber, ” bore x 450 mm long
010517 2 . . Hose clamp, worm drive, 18 - 25 mm27 001243 1 . Hose, rubber, “ BSP 28 010931 1 . Hose tail, ” x 1” hose29 010917 1 . Elbow, ” BSP galvanised, M/F30 010919 1 . Tee, ” BSP galvanised, M/M/M31 010946 1 . Adaptor, reducing, ” x “ BSP galvanised, M/F32 010962 1 . Adaptor, reducing, ” x ” BSP galvanised, M/F33 011173 1 . Elbow, swivel, ” BSP, M/F34 011160 1 . Adaptor, ” BSP, M/M35 011154 4 . . Seal, Dowty, ”36 011165 1 . Adaptor, ” x ” BSP, M/M37 014703 1 . Pulley, toothed, 40-8-2038 014453 1 . . Taper lock bush, 1610 x 24
011994 2 . . Key, rectangular, 8 x 6 x 25 round ends014447 1 . . Sleeve
39 014454 1 . Belt, toothed, 560 mm long40 012529 1 . Pulley, toothed, 32-8-2041 010575 1 . . Taper lock bush, 1610 x 30
000068 1 . . . Washer, ”, plain000014 1 . . . Nut, hex, ” UNF Nyloc
HIGH-PRESSURE PUMP ARRANGEMENT
1 2 3 4 56,7 8
9,7
1011
12,13
15
1617
11181920
21228
18
19
9,13
23
2425
27
28
2930
3117
32
33
34,35
9,13
36,35
12,13
263738
39
40 41
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 14
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
15 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HIGH-PRESSURE PUMP 21 LITRE - COMPONENTS1 014867 1 Pump 21 litre H-P1 014867SE 1 Pump 21 lire H-P (service exchange unit)2 013554 1 Poppet Valve Kit 1828 (see list below)3 N/A 6 . . Valve (complete), kit 18284 N/A 6 . . Seal, O-ring, kit 18285 N/A 6 . Valve seat, kit 18286 N/A 6 . Valve, kit 18287 N/A 6 . . Valve spring, kit 18288 N/A 6 . . Valve cage, kit 18289 014462 1 Water Valve Kit 1855 (see list below)
10 N/A 3 . . Seal, oil seal, kit 185511 N/A 2 . . Seal, O-ring, kit 185512 N/A 1 . . Cap seal, kit 185513 N/A 1 . . Seal, oil, kit 185514 021237 1 Water Seal Kit 1888 (see list below)15 N/A 3 . . Piston seal, kit 188816 N/A 3 . . Seal, O-ring, kit 188817 N/A 3 . . Gasket, kit 188818 021236 6 Seal, O-ring19 021238 1 Head20 021268 6 Valve plug21 021239 2 Plug ”22 021240 2 Seal, O-ring23 021241 3 Bearing gasket 22 Dia24 021242 3 Piston guide bush25 021243 1 Closed bearing support26 028705 2 Bearing27 021245 1 Pump body C/W end cap and O-ring28 021246 1 Oil filler plug29 021247 3 Piston seal nut30 021248 3 Washer31 021249 3 Piston, 22 Dia 32 021250 3 Separation disc33 021251 3 Seal, O-ring34 021252 3 Drive piston35 021253 3 Pin36 021254 3 Connecting rod 37 021255 1 Circlip38 021256 1 Oil level plug39 021257 1 O-ring40 021258 1 Rear cap41 021259 1 Eccentric shaft 42 021260 1 Key43 021261 1 Plug44 021262 1 Open bearing support45 021263 2 O-Ring46 021264 1 Plug47 021265 1 Seal, O-ring48 021266 1 Lining 0.1 48 021267 1 Lining 0.249 014448 2 Bracket, mounting
1
21 LITRE HIGH-PRESSURE PUMP
42
36
3738 40
39
4142
35
44
26
25
26
19
49
48
27
2324
46
29
3031
32
33
34
45
20
18
2221
3 4
2810 11
12
9 Kit 1855
11
13
9 KIT 1855
47
1516
17
14 Kit 1888
2 Kit 1828
34
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 16
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
17 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part no Quantity Description
STANDARD HOSE ARRANGEMENT & DETERGENTFEED VALVE (HAND LANCE)
NA 020451 1 AUTOMATIC HOSE REEL....................................................... Page H211 012548 1 Bracket, quick release coupling support
011011 1 . Setscrew, hex head, M8 x 25 mm log011073 1 . Nut, hex, M8 Nyloc
2 002008 1 . Adaptor, bulkhead, ” BSP, M/M3 023359 1 . Coupling, quick release, ” BSP, (male)4 023360 1 . . Coupling, quick release, ” BSP, (female)5 011159 1 . . . Adaptor, ” BSP, M/M6 011167 1 . . . Seal, dowty, ” BSP7 011167 1 Adaptor, ” x ” BSP, M/M8 013573 1 Nozzle injector9 002173 1 . Adaptor, ” BSP, M/F
10 011214 1 . Adaptor, ” BSP, F/F11 013575 As req . Tube, silicon
STANDARD HOSE ARRANGEMENT
DETERGENT FEED VALVE (HAND LANCE)
1
2 3
4 5,6
7
8
9
10
7
11
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 18
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
19 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
ItemPart Number Quantity Description
FAN WASH ASSIST ARRANGEMENTDETERGENT BOTTLE & FEED VALVE
NI 020451 1 AUTOMATIC HOSE REEL....................................................... Page H211 012548 1 Bracket, valve support
011010 1 . Setscrew, hex head, M8 x 25 mm long011073 1 . Nut, hex, M8 Nyloc
2 011269 1 . Adaptor, bulkhead, ” BSP, M/M3 011152 2 . . Seal, dowty, “ BSP4 011257 1 . Valve, ball, ” BSP, F/F5 011199 1 . Adaptor, ” x ” BSP, M/M6 011171 1 Elbow, swivel, ” BSP, M/F7 011167 1 . Adaptor, ” x ” BSP, M/M8 011233 1 Tee, ” BSP, M/M/F
011171 1 . Elbow, swivel, ” BSP, M/F011167 1 . Adaptor, ” BSP, M/M
9 010393 1 Bracket, bottle supportNI 022451 4 . Spacer
011410 4 . . Bolt, hex head, M8 x 75 mm long011073 4 . . Nut, hex, M8 Nyloc
10 013553 1 . Bottle, detergent11 013575 As req . Tube, silicon12 013575 1 . . Strap, bungee13 013573 1 Nozzle, injector14 011214 1 . Adaptor, ” BSP, F/F15 002008 1 . Adaptor, bulkhead, ” BSP, M/M
DETERGENT BOTTLE & FEED VALVE (WATER BOOM)
FAN WASH ASSIST ARRANGEMENT
1
2,3
4
5,3
6
7
8
9
10
11
12
1314 15
61
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 20
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
21 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HIGH-PRESSURE SPRAY SYSTEM - LAYOUT1 015017 1 . HIGH-PRESSURE PUMP ASSEMBLY..................................... Page H132 028761 1 . . Carrier, high-pressure pump (Located Behind Front Spray Bar)3 010748 1 . LANCE (MOUNTED IN CAB, UNDER SEATS).........................Page E9
NI 014666 1 . . Jet for lance4 011159 1 . . Adapter, ” BSP, M/M5 024463 1 . . . Swivel joint6 025290 1 . Filter assembly7 011174 1 . . Elbow8 010931 1 . . Hose tail ” x 1” BSP9 010959 1.4 metre . . Hose
010518 2 . . . Clamp, worm drive, 30 - 40 mm10 011301 1 . . Hose assemblyNI 020451 1 . Hose reel, auto retracting
Item Part no Quantity Description
HOSE REEL - COMPONENT PARTS1 020451 1 Automatic hose reel complete, less hose)2 024230 1 . Swivel elbow assembly3 025238 1 . . Roller assembly4 026217 1 . . Clamp5 026753 1 . . Spring, coiled (used on stainless steel reels only)6 026754 1 . . Spring, tension
NI 010601 13 m . . Hose, reinforced7 030570 1 . . Ratchet
3
4,5
2
110
9
86
7H
-P Lance stowage is in cab
3
2
1
AUTOMATIC HOSE REEL
5
4
6
7
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 22
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
23 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part no Quantity Description
WATER BOOM ARRANGEMENT1 027952 1 Carrier, hose reel
014796 1 . Bolt, pivot011060 1 . Nut, hex, M16, Nyloc011135 1 . Washer, M16, plain
NI 013012 2 . BushNI 014799 2 . Spacer sleeve2 023538 1 . Hose reel, retracting
000205 4 . . Setscrew, hex head, M14 x 25 mm long011127 4 . . Nut, hex, M14 Nyloc
3 011160 1 . . Adaptor, ” BSP, M/M4 027945 1 . Main Support Post (universal joint)5 010903 2 . . Nipple, straight, ” BSP, grease6 011173 1 . . Elbow, swivel, ” BSP
NI 011154 1 . . . Seal, Dowty, ” BSP7 011160 1 . . . Adaptor, ” BSP, M/M8 010970 1 . . . Hose, rubber, ” BSP x 460 mm long, straight ends9 027947 1 . Bracket, water boom support
10 010422 1 . . Joint, rotating, ” BSP11 011160 1 . . . Adaptor, ” BSP, M/MNI 011154 1 . . . Seal, Dowty, ” BSP12 027950 1 . . Plate, reinforcing
011032 6 . . . Setscrew, M10 x 30 mm long011075 6 . . . Nut, hex, M10 Nyloc
13 027949 1 . .Support bar, hoseNI 011724 9 . . Spacer, 20 mm x 12.5 mm x 11 mm
011055 3 . . Bolt, hex head, M12 x 65 mm long011051 4 . . Setscrew, hex head, M12 x 25 mm long011077 7 . . Nut, hex, M12 Nyloc
14 013486 2 . .Gas strut011075 4 . . Nut, hex, M10 Nyloc
15 027948 1 . Hook, stowage, water boom011032 4 . . Setscrew, M10 x 30 mm long011075 4 . . Nut, hex, M10 Nyloc
16 023360 1 . Coupling, quick-release, female, ” BSP17 011159 1 . . Adaptor, ” BSP, M/MNI 011153 1 . . Seal, Dowty ” BSP18 023359 1 . Coupling, quick-release, male, ” BSPNI 011153 1 . . Seal, Dowty ” BSP19 011199 1 . . Adaptor, ” BSP x ” BSP, M/M20 028155 1 . . Bracket, hose retainer21 011257 1 . . Valve, ball, high-pressure ” BSPNI 011152 1 . . . Seal, Dowty ” BSP
1 23
4
5,6,7 8
9
10,11
12
13
14
15
16
17
18
1920
21
HIGH-PRESSURE WATER BOOM ARRANGEMENT
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 24
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
25 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HIGH-PRESSURE SPRAY BAR ASSEMBLY 1 NA 1 PUMP, HIGH-PRESSURE ASSEMBLY...................................... Page H132 034073 1 Spray bar3 023148 2 . U-bolt4 002169 2 . Banjo bolt, ” BSP
011154 2 . . Seal, dowty ” BSP5 010112 5 . Nozzle body (brass)6 012316 5 . Spray jet LF4-80 (brass)7 030951 5 . Nozzle cap (brass)
Item Part Number Quantity Description
ADJUSTABLE SPRAYBAR MOUNT1 035570 1 Centre pivot2 028007 1 Clamp plate
3 000248 2 M8 grip nut with inset4 011073 2 Nut, hex, M8 Nyloc 5 027982 4 Pipe clamp block 25 mm single6 027990 2 Pipe clamp top plate7 026173 1 Plastic Plug 25.4 (Black)
ADJUSTABLE HIGH-PRESSURE SPRAYBAR MOUNT
7
5
6
4
3
2
1
FRONT BUMPER
HIGH-PRESSURE SPRAY BAR
1
25
6
7
3
4
ILLUSTRATED PARTS CATALOGUE Section HSCARAB VM MINOR - CANbus Page 26
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Washing & Dust Supression System
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
H
H Section ILLUSTRATED PARTS CATALOGUE
27 Page SCARAB VM MINOR - CANbus
Washing & Dust Supression System Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION JHYDRAULIC SYSTEM & RELATED COMPONENTS
TABLE OF CONTENTS
Assembly/Description Page
Main valve block assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Brush valve block assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Front brush ‘STOP WHEN RAISED’ valve components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Transmission pump assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Suction pump assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Gear pump assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Complete transmission assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Radiator (oil cooler) assembly - EURO 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Manifold assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Radiator (oil cooler) assembly - EURO 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Oil tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Suction filter assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Power steering-regulator Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17High-pressure pump drive motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Widesweep brush motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Side/front brush motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
HYDRAULIC RAMSSuction nozzle-lift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Suction nozzle-tilt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Widesweep-lift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Front brush-lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Front brush-swing-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Side brush-lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Side brush-swing-out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Hopper-Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Auto-blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Rear door-open/close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Cab assist-lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Rear door-flow valve & pressure control assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Rear door-check valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Auto-Blanking valve arrangement, single sweep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29Auto-Blanking valve arrangement, dual sweep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29Steel pipe listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Rubber hose listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31Rubber hose listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32NOTE: Unless stated all parts are common for EURO 4 and 5 models
J Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
MAIN VALVE BLOCK ASSEMBLY 1 025121 1 Main valve block 2 014663 10 . Solenoid (GS023300N)3 014655 10 . . Coil, 14 Watt4 025891 1 . Solenoid (GS041300N)5 021753 1 . . Coil, 19 Watt6 021744 1 . Solenoid (GS042100N)7 021768 1 . . Coil, 28 Watt8 020005 4 . Solenoid (GS05300)9 004208 4 . . Coil, 18 Watt
10 033918 1 . Relief valve, brush lift (AO2B2HZ1-120N)11 033917 1 . Relief valve, main (AO4B2PT32-170N)NI 032823 2 . . Relief valve capNI 004205 1 Check valve (D04B2-21N)NI 004295 1 . Pilot piston (PP045P)
MAIN VALVE BLOCK ASSEMBLYDual Sweep Version Shown
2,3
4,5
6,7 8,910 11
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
BRUSH VALVE BLOCK1 025119 1 Valve block 4-spool, sterling BSK15696-B 2 014661 4 . Solenoid valve GS041200N 3 025890 4 . Solenoid valve GS040200N 4 021753 8 . Solenoid coil, CCP 19 Watt, 12 Volt
NI 011153 11 . Seal, Dowty ” NI 011159 3 . Adaptor, ” BSP, M/MNI 020903 7 . Stud, male, 12 x ” BSPNI 011242 1 . Plug, ” BSP NI 000141 2 . Screw, socket cap head, M6 x 80 mm long
Item Part Number Quantity Description
FRONT BRUSH ‘STOP WHEN RAISED’ VALVE COMPONENTSNI 025890 2 Valve - GS040200NNI 014661 2 Valve - GS041200N]NI 021753 4 Coil 12 Volt / 19 WattNI 028234 1 Wiring loom - front brush stop
3,4
2,4
1
BRUSH CONTROL VALVE BLOCK
3,43,43,4
2,42,42,4
Left HandSide Brush
Right HandSide Brush
Left Hand Front BrushRight Hand Front Brush
Left Hand Front BrushRight Hand Front Brush
NOTE:Left or Right side brush valve positions will be blanked off according to build configuration unless M/C is dual sweep.
For special build configurations not covered here, i.e. utilising either of the spare side brush positions, please refer to your Scarab agent or to the Scarab Parts Department, stating M/C Serial Number and details of any non-standard fittings.
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
TRANSMISSION PUMP ASSEMBLY1 024516 1 Pump, transmission
NI 024516(SE) 1 Pump, transmission, (service exchange unit)2 011190 1 . Adaptor, 1 ” UNF (SAE) x ” BSP3 002084 1 . . Hose tail, ” BSP x 1” hose4 011319 1 . Hose, rubber, 1 ” BSP, straight end + 90°5 011226 3 . Adaptor, ” UNF (SAE) x ” BSP, M/M6 011167 1 . . Elbow, swivel, ” BSP x ” hose7 013887 1 . Valve, relief, “ BSP8 011152 4 . . Seal, Dowty, ” BSP9 011158 3 . . Adaptor, “ BSP, M/M
10 011169 1 . . Elbow, swivel, “ BSP, F/F11 011264 2 . . Adaptor, ” UNF (SAE) x “ BSP, M/M12 032884 1 . Drive hub13 026655 2 . Valve, Reverse/Forward drive14 026775 4 . . Cap, plastic, cap head cover15 002112 1 . Adaptor, swivel, “ BSP, M/F16 014655 1 . Coil, 12 Volt17 013888 1 . Valve, Reverse, “ BSPNI 025728 * 1 . Seal, O-ring, adaptor plate with (SLOTTED FIXING HOLES)NI 036829 * 1 . Seal, O-ring, adaptor plate with (ROUND FIXING HOLES)
* When ordering check the flange plate fixing hoses. If in doubt contact Scarab Parts Department.
NOTE: Picture shown with drive coupling blanking cap fitted
1
2
3
4
65
5 12
12
15,816
178,9
13
TRANSMISSION PUMP ASSEMBLY
14
ADAPTOR PLATE
7
10
11
8,9
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
SUCTION FAN PUMP ASSEMBLY1 023620 1 Suction fan pump2 011318 1 . Hose, rubber, ” BSP, straight ends3 011227 1 . Adaptor, ” UNF (SAE) x ” BSP, M/M4 014217 1 . Valve, DFR5 002192 1 . Test point ” UNF (SAE)6 011230 2 . Flange, 1 ” (SAE) 7 011231 1 . Elbow, flanged, 1 ” (SAE) x 1” hose
011108 4 . . Screw, socket cap head, ” UNC x 1 ” long8 013689 1 . Valve, suction fan
011107 4 . . Screw, socket cap head, ” UNC x 2 ” long9 011155 1 . Plug, ” BSP
10 011155 2 . . Seal, Dowty, ”11 011199 1 . Adaptor, ” x ” BSP, M/M12 011153 2 . . Seal, Dowty, ” BSP13 011242 1 . Plug, ” BSP14 014655 1 . Coil, 12 Volt15 014654 1 . Solenoid16 011161 1 . Adaptor, ” BSP, M/M
NOTE: Picture shown with drive coupling blanking cap fitted
1
2 34
5
76
8
9,10
14
16,10
14
13,12
15
SUCTION FAN PUMP ASSEMBLY
11,12
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
GEAR PUMP ASSEMBLY1 024592 1 Gear pump (double)2
Per gear pump
027056 1 . Elbow, suction013518 1 . . Seal, O-ring011011 4 . . Setscrew, hex head, M8 x 25 mm long011093 4 . . Washer, M8, spring
3 024537 1 . Valve, flow controlNI 024486 1 . Seal, O-ring, kit
000227 4 . . Bolt, hex head, M8 x 110 mm long011093 4 . . Washer, M8, spring011092 4 . . Washer, M8, plain
4 011160 1 . Adaptor, ” BSP, M/M5 011154 2 . . Seal, Dowty, ”6 011242 1 . Plug, ” BSP7 011153 2 . . Seal, Dowty, ” BSP8 011167 1 . Adaptor, ” x ” BSP, M/M9 011172 1 . Elbow, swivel, ” BSP, M/F
Item Part Number Quantity Description
COMPLETE TRANSMISSION ASSEMBLY1 032569 1 Bracket, transmission support, LH2 035670 1 Bracket, transmission support, RH3 013409 4 Mounting, rubber
011075 4 . Nut, hex, M10 Nyloc011074 8 . Washer, 10 mm
4 031293 1 Cross member - EURO 4NI 037142 1 Cross member - EURO 5
NOTE:Unless stated all parts are common for EURO 4 and 5 models
1
2
3
8,5
9
GEAR PUMP ASSEMBLY
TRANSMISSION PUMP SUCTION FAN PUMP GEAR PUMP
1
2
3
4
COMPLETE TRANSMISSION ASSEMBLY
4,5
6,7
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 10
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
RADIATOR ASSEMBLY - EURO 41 034130 1 Radiator/Cooler (complete), less motor2 025372 1 . Hydraulic motor 14 cc3 011154 2 . . Adaptor, ” x ” BSP, M/F4 011154 2 . . Seal, Dowty, ” BSP5 010913 1 . . Elbow, swivel, ” BSP, M/F6 011343 1 . . Hose, rubber, ” BSP x 4000mm long, straight ends7 010910 1 . Elbow, galvanised, ” BSP, M/F8 003010 1 . . Hose tail, ” BSPT x ” bore pipe9 011160 1 . Adaptor, ” BSP, M/M
10 011234 1 . . Elbow, hose tail swivel, ” BSP x ” bore pipe11 001204 1 . . Pipe, rubber, ” bore x 800mm long12 010516 2 . . Clamp, worm drive, 11 - 16mm13 001219 1 . Hose, rubber, ” BSP x 360mm long, straight end + 90° 14 002843 1 . Elbow, 45° swivel, ” BSP,M/F15 002079 1 . . Elbow, hose tail swivel, ” BSP x 1” bore pipe16 001184 1 . Pipe, rubber, ” x 1720 mm long bore17 010517 2 . . Clamp, worm drive, size 18 - 25mm18 010959 1 . Pipe, rubber, 1” x 350 mm long19 014828 2 . . Clamp, worm drive, 25 -40mm, High-torque20 002154 1 . Tee, ” x ” x ”, M/M/M21 001220 1 . Hose, rubber, ” BSP x 410mm long, straight end + 90°22 011235 1 . Hose, rubber, ” BSP x 861mm long, straight ends23 011301 1 . Hose, rubber, ” BSP x 2540mm long, straight ends
Item Part Number Quantity Description
MANIFOLD ASSEMBLIES1 025148 1 Manifold, oil return2 021575 1 . Pipe, rubber, 2” bore x 230mm long3 028778 4 . . Clamp, worm drive, 40 - 70mm, High-torque
011001 3 . . . Setscrew, hex head, M6 x 16mm long011071 3 . . . Nut, M6 Nyloc
4 026868 1 . . Bracket, manifold011001 2 . . . Setscrew, hex head, M6 x 16mm long011071 2 . . . Nut, M6 Nyloc
5 027742 1 Manifold, oil tank feed6 022442 1 . Pipe, rubber, 2” bore x 280mm long
010959 1 . Pipe, rubber, 1” x 350mm long011001 3 . . . Setscrew, M6 x 16mm long011071 3 . . . Nut, M6 Nyloc
NOTE:Unless stated all parts are common for EURO 4 and 5 models
RADIATOR ASSEMBLY
123,4,56
13
14
1516,17
20
21
22
1
2,3
4
5
6,3
11,12
18,19
MANIFOLD ASSEMBLY
7,8
3,4,523
USED WHEN STREETWASH FITTED
9,10,4
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 12
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
13 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
RADIATOR ASSEMBLY - EURO 51 037143 1 Radiator/Cooler (complete), less motor
NI 037703 1 . Partition2 025372 1 . Hydraulic motor 14 cc3 011154 1 . . Adaptor, ” x ” BSP, M/F4 011154 2 . . Seal, Dowty, ” BSP5 011233 1 . . Tee, swivel, ” BSP, M/M/F6 001252 1 . . Hose, rubber, ” BSP x 2540mm long, straight end + 90º7 010910 1 . Elbow, galvanised, ” BSP, M/F8 003010 1 . . Hose tail, ” BSPT x ” bore pipe9 011160 1 . Adaptor, ” BSP, M/M
10 002110 . . Tee, swivel, ” x ” x ” BSP, M/M/F11 011234 1 . . Elbow, hose tail swivel, ” BSP x ” bore pipe12 001184 1 . Pipe, rubber, ” x 1720 mm long bore13 010517 2 . . Clamp, worm drive, size 18 - 25mm14 001204 1 . . Pipe, rubber, ” bore x 800mm long15 010516 2 . . Clamp, worm drive, 11 - 16mm16 011308 1 . Hose, rubber, ” BSP x 500mm long, straight ends17 001220 1 . Hose, rubber, ” BSP x 410mm long, straight end + 90º18 037227 1 . Valve, flow control, cooler
011068 2 . . setscrew, hex head, M6 x 35mm long011091 2 . . Washer, M6, spring011090 2 . . Washer, M6, plain
NI 037425 1 . . Bracket , flow control valve011001 2 . . . Setscrew, hex head, M6 x 16mm long011091 2 . . . Washer, M6, plain
19 001253 1 . Hose, rubber, ” BSP x 3250mm long, straight end + 90º20 002084 1 . Hose tail, ” BSP x 1” hose21 010959 1 . Pipe, rubber, 1” x 350 mm long21 014828 2 . . Clamp, worm drive, 25 -40mm, High-torque
1
2
3,4,5
6
7,8
4,9,10,11
12,13
14,15
16
17
18
3,4,519
USED WHEN STREETWASH FITTED
RADIATOR ASSEMBLY - EURO 5
20,21,22
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 14
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
15 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
OIL TANK ASSEMBLY1 025142 1 Oil tank2 023155 1 . Gauge, fluid level
NI 021979 2 . . Seal, rubber3 022782 1 . Gasket, oil tank4 022781 1 . Lid, oil tank
NI 033243 1 . Lid, oil tank. (Used when Teal wash fitted)011111 24 . . Screw, Taptite, 10-32 UNF x ”
5 020689 1 . Adaptor, 1” x ” BSP, M/F6 011156 1 . . Seal, Dowty 1” BSP7 020688 1 . Filter, breather8 011152 1 . . Seal, Dowty ” BSP9 011723 1 . Filter, return (complete)
NI 011972 1 . . Filter, return, element onlyNI 022163 1 . . O-Ring Kit (011723 filter return)NI 030907 1 . . Spring (011723 filter return)10 011161 1 . Adaptor, ” BSP, M/M11 010917 1 . Elbow, Swivel, ” BSP, M/F12 020687 1 . Filter, Suction element13 010305 1 . Magnet (Inside Tank)14 003006 1 . Adaptor, ” x ” BSP, galvinised, M/F15 010944 1 . Adaptor, ” BSP, galvinised, M/M16 011743 1 . Valve, ball, ” BSP17 010910 1 . Elbow, ” BSP, galvinised, M/F18 010945 1 . Plug ” BSP, galvanisedNI 028760 1 Label - oil tank
Item Part Number Quantity Description
SUCTION FILTER ASSEMBLY (CHASSIS MOUNTED)NA 021730 1 Filter, suction (complete)
1 021038 1 . Filter, suction element2 021731 1 . Filter, suction head
011022 4 . . Setscrew, hex head, ” UNC x ” long011406 4 . . Washer, spring, ”
NI 021673 1 . Bracket, support suction filter3 001075 1 . Hose, rubber, ” x 500mm long, straight end + 90°4 001076 1 . Hose, rubber, ” x 600mm long, straight end + 90°5 011265 2 . . Adaptor, 1 ” UNF (SAE) x ” long, complete with O-ring
1
2
3
4
5
6
7
8
9
10 11
12
13OIL TANK ASSEMBLY
1
14
15
16
17
184
SUCTION FILTER ASSEMBLY
2
3
5, 6
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 16
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
17 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
POWER STEERING-REGULATOR VALVE1 025599 1 Valve, regulator2 011167 2 . Adaptor, ” x ” BSP, M/M3 011160 1 . Adaptor, ” BSP, M/M4 011154 3 . . Seal, Dowty, ” BSP
000009 2 . Bolt, hex head, M8 x 55mm long011092 2 . Washer, M8, plain011073 2 . Nut, hex, M8 Nyloc
Item Part Number Quantity Description
HIGH-PRESSURE PUMP-DRIVE MOTOR1 021315 1 Pump, hydraulic, 15cc, 1MR0152 011158 1 . Adaptor, ” BSP, M/M3 011150 1 . Seal, Dowty, ” BSP4 011167 2 . Adaptor, ” x ” BSP, M/M5 011154 2 . Seal, Dowty, ” BSP
1
2,4
3,4
1
2,3
4,5
HIGH PRESSURE PUMP-DRIVE MOTOR
POWER STEERING-REGULATOR VALVE
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 18
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
19 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WIDESWEEP BRUSH MOTOR1 010747 1 Motor, hydraulic, OMP 200 (Single sweep)
NI 023069 1 . Seal, motor, repair kit, OMP 2002 023503 1 Motor, hydraulic, OMPW 200 (Dual sweep)
NI 011221 1 . Seal, motor, repair kit, OMPW 2003 011167 2 . Adaptor, ” x ” BSP, M/M 4 011154 2 . Seal, Dowty, ” BSP 5 011241 1 . Plug, “ BSP, M/M6 011150 1 . Seal, Dowty, ” BSP
Item Part Number Quantity Description
SIDE/FRONT BRUSH MOTOR1 010006 1 Motor, hydraulic, OMP 315
NI 023069 1 . Seal, motor, repair kit, OMP 315NI 027825 1 . Seal, dust, motor shaft, 2 011167 2 . Adaptor, ” x ” BSP, M/M3 011154 2 . Seal, Dowty, ” BSP 4 011172 2 . Elbow, swivel, ” BSP, M/F
1
2
3,4
5,6
1
2,3
4
SIDE/FRONT BRUSH MOTOR
WIDESWEEP MOTOR
OMP 315
OMPW 200
OMP 200
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 20
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
21 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
SUCTION NOZZLE-LIFT RAM1 027119 1 Ram, hydraulic
NI 011629 1 . Seal, ram, repair kit2 014473 1 . Bellows3 027804 1 . Adaptor, restrictor, “ BSP x ” orifice, M/M, (orange)4 011152 1 . Seal, Dowty, “ BSP
Item Part Number Quantity Description
SUCTION NOZZLE-TILT RAM1 027113 1 Ram, hydraulic
NI 011629 1 . Seal, ram, repair kit2 011152 1 . Adaptor, restrictor, ” BSP x 0.6 mm orifice, M/M, (green)3 011152 1 . Seal, Dowty, ” BSP
Item Part Number Quantity Description
WIDESWEEP-LIFT RAM1 027115 1 Ram, hydraulic
NI 011629 1 . Seal, ram, repair kit2 021510 1 . Bellows
1
2,3
12 3,4
1
2
3,4
WIDESWEEP-LIFT RAM
SUCTION NOZZLE-TILT RAM
SUCTION NOZZLE-LIFT RAM
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 22
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
23 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
FRONT BRUSH-LIFT RAM1 027116 1 Ram, hydraulic
NI 011629 1 . Seal, ram, repair kit2 021510 1 . Bellows3 011152 1 . Adaptor, restrictor, ” BSP x 0.6 mm orifice, M/M, (green)4 011152 1 . Seal, Dowty, ” BSP
Item Part Number Quantity Description
FRONT BRUSH-SWING-OUT RAM1 036009 1 Ram, hydraulic
NI 011629 1 . Seal, ram, repair kit2 021510 1 . Bellows3 011152 1 . Adaptor, restrictor, ” BSP x 0.6 mm orifice, M/M, (green)4 011152 1 . Seal, Dowty, ” BSP
Item Part Number Quantity Description
SIDE BRUSH-LIFT RAM1 027114 1 Ram, hydraulic
NI 011629 1 . Seal, ram, repair kit2 021510 1 . Bellows3 011152 1 . Adaptor, restrictor, ” BSP x 0.6 mm orifice, M/M, (green)4 011152 1 . Seal, Dowty, ” BSP
Item Part Number Quantity Description
SIDE BRUSH-SWING-OUT RAM1 027118 1 Ram, hydraulic
NI 011629 1 . Seal, ram, repair kit2 021510 1 . Bellows3 011152 1 . Adaptor, restrictor, ” BSP x 0.6 mm orifice, M/M, (green)4 011152 1 . Seal, Dowty, ” BSP
12 3,4
123,4
12
3,4
1
2
3.4
SIDE BRUSH-SWING-OUT RAM
SIDE BRUSH-LIFT
FRONT BRUSH-SWING-OUT
FRONT BRUSH-LIFT RAM
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 24
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
25 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
HOPPER-LIFT RAM1 011577 1 Ram, hydraulic (standard)
NI 012203 1 . Seal, ram (011577), repair kitNI 026730 2 Ram, hydraulic (Hi-tip 1.3)NI 026719 2 Ram, hydraulic (Hi-tip 1.6)2 011158 2 . Adaptor, ” BSP, M/M3 011151 2 . Seal, Dowty, ” BSP
Item Part Number Quantity Description
AUTO-BLANKING RAM1 022350 As req Ram, hydraulic
NI 022776 1 . Seal, repair kit2 002017 2 . Adaptor, banjo, ” BSP, M/M3 011151 4 . Seal, Dowty, ” BSP4 1 . Nut, hex, clevis locking,5 014469 1 . Clevis6 1 . . Retaining pin, clevis7 1 . . Clip, clevis retaining pin
Item Part Number Quantity Description
REAR DOOR-OPEN/CLOSE RAM1 022511 1 Ram, hydraulic
NI 022777 1 . Seal, repair kit2 002017 2 . Adaptor, banjo, ” BSP, M/M3 011151 4 . Seal, Dowty, ” BSP
Item Part Number Quantity Description
CAB ASSIST-LIFTING RAM1 032810 1 Ram, hydraulic
NI 011629 1 . Seal, repair kit2 011158 2 . Adaptor, ” BSP, M/M3 011151 2 . Seal, Dowty, ” BSP
12,3
2,3
1
1
2,3
4
56
2,3
1
REAR DOOR-OPEN/CLOSE RAM
AUTO-BLANKING RAM
HOPPER-LIFT RAM
CAB-ASSIST RAM
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 26
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
27 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
REAR DOOR-FLOW VALVE & PRESSURE CONTROL ASSEMBLY1 021505 1 Cetop sub plate2 023569 1 Valve, control ‘E’ spool, 12 Volt3 026049 2 . Coil, solenoid, 12 Volt x 30 Watt (2.5 amps)4 010923 1 . Hose tail, ” BSP x ” hose5 011153 1 . Seal, Dowty, ” BSP6 020903 2 . Adaptor, ” BSP x 12 mm steel tube, M/M7 011154 4 . Seal, Dowty, ” BSP8 032503 1 . Tube, assembly9 01110 1 . Adaptor, ” BSP, M/M
10 011234 1 . Hose tail, 90°, ” BSP x ” hose11 011165 1 . Adaptor, ” x ” BSP, M/M12 011171 1 . Elbow, swivel, ” BSP, M/F
Item Part Number Quantity Description
REAR DOOR-CHECK VALVE1 012582 1 Valve, check2 022483 1 . Coil, solenoid, 12 Volt x 14 Watt3 011158 2 . Adaptor, ” BSP, M/M4 011171 2 . Elbow, swivel, ” BSP, M/F5 011152 2 . Seal, Dowty, ” BSP
1
2
4,5
3
6.7
8
9,7
10
11,7
12
REAR DOOR-FLOW VALVE & PRESSURE CONTROL ASSEMBLY
1
2
3,4,5
REAR DOOR CHECK VALVE
3
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 28
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
29 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
AUTO-BLANKING VALVE ARRANGEMENT1 021505 1 Cetop, sub plate2 023578 1 . Valve, control D spool, 12 Volt
000137 4 . . Screw, socket cap head, M5 x 50 mm long3 011159 1 . Adaptor, ” BSP, M/M4 011153 4 . . Seal, Dowty, ” BSP5 011223 1 . . Elbow, swivel, ” BSP x ” hose6 011199 3 . Adaptor, ” x ” BSP, M/M7 011171 1 . . Elbow, swivel, ” BSP, M/F
Item Part Number Quantity Description
AUTO-BLANKING VALVE ARRANGEMENT (DUAL SWEEP)1 021810 1 Bracket, valve support
000037 4 . Screw, socket cap head, M6 x 40 mm long011073 4 . Nut, hex, M8 Nyloc
2 011172 1 Elbow, swivel, ” BSP, M/F3 011223 1 . Tee, swivel, ” BSP, M/M/F4 011171 1 Tee, swivel, ”, BSP, M/M/F
12
3,45 6,4
7
1
2
3,4
6,4
6,4
AUTO-BLANKING VALVE ARRANGEMENT
SINGLE SWEEP LH/RH, DUAL SWEEP RH DUAL SWEEP LH
1
2
3
4
DUAL SWEEP ARRANGEMENT
6,4
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 30
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
J Section ILLUSTRATED PARTS CATALOGUE
31 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
STEEL PIPE LISTINGNI 033245 1 Hydraulic Pipe - LF1- LH FRONT BRUSH NI 033246 1 Hydraulic Pipe - LF2 -LH FRONT BRUSH NI 033251 1 Hydraulic Pipe - C1- LH FRONT BRUSH LIFT NI 033252 1 Hydraulic Pipe - C2 - LH FRONT BRUSH SWINGNI 027696 1 Hydraulic Pipe - VALVE BLOCK LH1 - LH SIDE BRUSHNI 027697 1 Hydraulic Pipe - VALVE BLOCK LH2 - LH SIDE BRUSHNI 026903 1 Hydraulic Pipe - BLOCK - LH SIDE BLOCKNI 026904 1 Hydraulic Pipe - LH2 - LH SIDE BRUSHNI 026922 1 Hydraulic Pipe - C7 - LH SIDE BRUSH LIFTNI 026917 1 Hydraulic Pipe - C9 - LH NOZZLE NI 033545 1 Hydraulic Pipe - C6 - LH/RH NOZZLE TILTNI 033547 1 Hydraulic Pipe - C6 - LH NOZZLE TILTNI 033548 1 Hydraulic Pipe - C6 - LH NOZZLE TILT (Dual Sweep)NI 026899 1 Hydraulic Pipe - D - HIGH-PRESSURE PUMPNI 026902 1 Hydraulic Pipe - HIGH-PRESSURE PUMP RETURN NI 033247 1 Hydraulic Pipe - RF1 - RH FRONT BRUSH NI 033248 1 Hydraulic Pipe - RF2 - RH FRONT BRUSH NI 033249 1 Hydraulic Pipe - C4 - RH FRONT BRUSH LIFTNI 026909 1 Hydraulic Pipe - C4 - RH FRONT BRUSH LIFTNI 033250 1 Hydraulic Pipe - C5 - RH FRONT BRUSH SWINGNI 026910 1 Hydraulic Pipe - C5 - RH FRONT BRUSH SWINGNI 026906 1 Hydraulic Pipe - RH1 - RH SIDE BRUSHNI 026907 1 Hydraulic Pipe - RH2 - RH SIDE BRUSHNI 026911 1 Hydraulic Pipe - C3 RH SIDE BRUSH SWINGNI 026916 1 HydraulicPipe - C10 - RH NOZZLENI 033546 1 Hydraulic Pipe - C6 - RH NOZZLE TILTNI 027694 1 Hydraulic Pipe - WIDESWEEP- MANIFOLDNI 026908 1 Hydraulic Pipe - T - WIDESWEEPNI 026905 1 Hydraulic Pipe - WIDESWEEP RETURNNI 027695 1 Hydraulic Pipe - BLOCK - WIDESWEEPNI 026923 1 Hydraulic Pipe - C8 - WIDE SWEEP LIFTNI 026914 1 Hydraulic Pipe - A - HOPPER NI 026915 1 Hydraulic Pipe - B - HOPPER NI 026918 1 Hydraulic Pipe - FAN PUMP TO C
Item Part Number Quantity Description
RUBBER HOSES COMMON ON, LH, RH, DUAL SWEEP M/CsNI 001070 1 Hose ” x 4350 (ST/90) - FAN RETURNNI 001075 1 Hose ” x 500 (ST/90) - SAUER PUMP - FILTERNI 001076 1 Hose ” x 600 (ST/90) - SAUER PUMP - FILTERNI 001163 4 Hose ” x 1030 (ST/90) - FRONT BRUSH MOTORNI 001085 1 Hose ” x 4300 (ST/90) - H/P PUMP - HOSE REELNI 011342 1 Hose ” x 2540 (ST/90) - COOLER MOTOR - G/PUMP 2NI 001167 1 Hose ” x 1200 (ST/ST) - COOLER MOTOR - RESTRICTORNI 001084 1 Hose ” x 2330 (ST/90) - RESTRICTOR - AIR COM PUMPNI 011342 1 Hose ” x 2540 (ST/90) - AIR CON PUMP - TEENI 001088 1 Hose ” x 580 (ST/90) - TEE - SWEEP WASH VALVENI 011342 1 Hose ” x 2540 (ST/90) - AIR CON PUMP - RESTRICTORNI 001100 2 Hose ” x 460 (ST/90) - FRONT BRUSH SWINGNI 001101 2 Hose ” x 1125 (ST/90) - FRONT BRUSH LIFT
ILLUSTRATED PARTS CATALOGUE Section JSCARAB VM MINOR - CANbus Page 32
Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10 Hydraulic System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
J
Item Part Number Item Part NumberQuantityDescription
RUBBER HOSES COMMON ON LH, RH, DUAL SWEEP M/CsNI 014157 1 Hose ” x 2230 (ST/90) - FAN PUMP - HOPPERNI 001104 2 Hose ” x 900 (ST/90) - S/PIPE - HOPPER RAMNI 001088 1 Hose ” x 750 (ST/90) - S/PIPE - H/P PUMP (Return)NI 001008 1 Hose ” x 650 (ST/90) - S/PIPE - H/P PUMP (Feed)NI 011309 1 Hose ” x 432 (ST/90) - S/PIPE - TEENI 001220 1 Hose ” x 410 (ST/90) - TEE - TEENI 001219 1 Hose ” x 360 (ST/90) - TEE COOLERNI 001230 1 Hose ” x 1460 (90/90) - POWER STEERING PUMP- RESTRICTORNI 001103 1 Hose ” x 265 (ST/90) - SIDE BRUSH SWINGNI 001105 1 Hose ” x 400 (ST/90) - SIDE BRUSH LIFTNI 010990 1 Hose ” x 600 (90/90) - S/PIPE - NOZZLE TILTNI 001101 2 Hose ” x 1125 (ST/90) - S/PIPE - MANIFOLD (Hi-TIP)NI 001105 2 Hose ” x 400 (ST/90) - MANIFOLD -HOPPER RAM (1.3 Hi-Tip)NI 001100 2 Hose ” x 460 (ST/90) - MANIFOLD - HOPPER RAM (1.3 Hi-Tip)NI 010990 2 Hose ” x 600 (ST/90) - MANIFOLD - HOPPER RAM (1.6 Hi-Tip)NI 010991 2 Hose ” x 550 (ST/90) - MANIFOLD - HOPPER RAM (1.6 Hi-Tip)
Item Part Number Quantity Description
RUBBER HOSES ON RH SWEEP M/Cs ONLY NI 001082 2 Hose ” x 700 (90/90) - SIDE BRUSHNI 001105 1 Hose ” x 400 (ST/90) - WIDE SWEEP LIFTNI 001108 1 Hose ” x 750 (ST/90) - S/PIPE - FAN PUMPNI 010980 1 Hose ” x 432 (ST/90) - HOPPER VALVE - S/PIPENI 001024 1 Hose ” x 770 (ST/90) - HOPPER RAM - S/PIPENI 011340 1 Hose ” x 3000 (ST/90) - STREETWASH VALVE - FRONT SPRAY BARNI 001090 1 Hose ” x 880 (ST/90) - SWEEP/WASH VALVE - G/PUMPNI 001226 1 Hose ” x 530 (ST/90) - RESTRICTOR - STEERING BOXNI 001226 1 Hose ” x 530 (ST/90) - BOX - RETURN MANIFOLD
Item Part Number QuantityDescription
RUBBER HOSES ON LH SWEEP M/Cs ONLYNI 001081 2 Hose ” x 650 (90/90) - SIDE BRUSHNI 001130 1 Hose ” x 265 (ST/90) - WIDE SWEEP LIFTNI 001105 1 Hose ” x 400 (ST/90) - S/PIPE - NOZZLE TILTNI 001105 1 Hose ” x 400 (ST/90) - NOZZLE LIFTNI 001108 1 Hose ” x 750 (ST/90) - BLOCK - FAN PUMPNI 001120 1 Hose ” x 432 (ST/90) - S/PIPE - TEENI 001088 2 Hose ” x 580 (ST/90) - S/PIPE - WIDE SWEEPNI 001227 1 Hose ” x 680 (ST/90) - RESTRICTOR - STEERING BOXNI 001227 1 Hose ” x 680 (ST/90) - BOX - RETURN MANIFOLD
Item Part Number QuantityDescription
RUBBER HOSES LH DRIVE DUAL SWEEP M/Cs ONLYNI 001019 2 Hose ” x 820 (ST/90) S/PIPE - WIDE SWEEPNI 001105 1 Hose ” x 400 (ST/90) S/PIPE - WIDE SWEEP LIFT
If in doubt contact the Parts Department quoting your Machine Serial number.
J Section ILLUSTRATED PARTS CATALOGUE
33 Page SCARAB VM MINOR - CANbus
Hydraulic System & Related Equipment Manual Number Z036776 / Issue: Amdt. 1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR - CANbus
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION KELECTRICAL SYSTEM & RELATED EQUIPMENT
TABLE OF CONTENTS
Assembly/Description Page
Fuse panel assembly & relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1ECU & Node enclosure - EURO 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3ECU, Controller & Node arrangement - EURO 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
LIST OF ELECTRICAL PARTS
Wiring looms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5CANbus components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Cab internal electrical components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Head lamps - rear lamps & side markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Work lamps - beacons & bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Electrical components - gantry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
NOTE:Unless stated all parts are common for EURO 4 and 5 models
K Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Electrical System & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
FUSE PANEL ASSEMBLY - ASSOCIATED PARTS1 034790 1 Fuse panel frame. LH (shown)1 034791 1 Fuse Panel frame. RH 2 031996 1 . Fuse holder, 6-way3 032804 1 . Relay, 70 Amp, 12 Volt with diode4 031668 1 . Intermittent wash/wipe control unit5 032427 1 . ZG - Hydrive - B node6 See Below . Fuses
014286 17 . . 5 Amp, blade type014288 5 . . 10 Amp, blade type014289 5 . . 15 Amp, blade type014290 3 . . 20 Amp, blade type014292 3 . . 30 Amp, blade type
7 011768 7 . Relay, cross-over, 12 Volt8 100125 1 . Relay, directional indicators
NI 034793 1 LABEL - FUSE & RELAY INFORMATION. LH 9 034794 1 LABEL - FUSE & RELAY INFORMATION. RH
NI 025750 1 Fuse box door coverNI 021326 2 Dsuz fastener receptacleNI 021327 2 Dsuz fastener studNI 021328 2 Dsuz fastener retainer
5
1
6
7
1
2
3
4
8
FUSE PANEL ASSEMBLY
ILLUSTRATED PARTS CATALOGUE Section KSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Electrical System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
K
K Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Electrical System & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
ECU & NODE ENCLOSURE - EURO 41 033189 1 Enclosure base
011001 4 . Setscrew, hex head, M6 x 16 mm long011090 8 . Washer, M6, plain011071 4 . Nut, hex, M6 Nyloc
2 034056 1 . ECU 000020 3 . . Setscrew, hex, M6 x 30 mm long
3 033191 1 . . Bracket, mounting, ECU & node 000350 4 . . . Screw, socket button head, M6 x 20 mm long
4 032539 2 . Node (CANbus)000052 4 . . Setscrew, hex head, M5 x 16 mm long011145 4 . . Washer, 2BA, plain
5 033192 1 . . Bracket, support, node000350 2 . . . Screw, socket button head, M6 x 20 mm long000052 1 . . . Setscrew, hex head, M5 x 16 mm long
NI 033109 1 . Cover, enclosureNI 000248 2 . . Hand screw, plastic, M8
011092 2 . . Washer, M8, plain011093 2 . . Washer, M8, spring
Item Part Number Quantity Description
ECU, CONTROLLER & NODE ARRANGEMENT - EURO 51 037425 1 Bracket, controller
011001 2 . Setscrew, hex head, M6 x 16mm long011071 2 . Nut, hex, M6 nyloc
2 037228 1 . Controller, CR2500000052 4 . . Setscrew, hex head, M5 x 16mm long000155 4 . . Nut, M5 nyloc
3 037154 1 Bracket, node support011010 2 . . Setscrew, hex head, M8 x 20mm long011093 2 . . Washer, M8, spring
4 032539 2 . Node (CANbus)000020 4 . . Setscrew, hex head, M6 x 30mm long011090 8 . . Washer, M6, plain011071 4 . . Nut, hex, M6 nyloc
5 037935 1 ECU011087 4 . Setscrew, hex head, M6 x 25mm long011090 4 . Washer, M6, plain
NOTE:The ECU must be matched to the engine by serial number
1
2 34
5
1
2
3 4
5
ECU & NODE ENCLOSURE - EURO 4
ECU, CONTROLLER & NODE ARRANGEMENT - EURO 5
ILLUSTRATED PARTS CATALOGUE Section KSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Electrical System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
K
K Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Electrical System & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
LIST OF ELECTRICAL PARTSItem Part Number Quantity Description
WIRING LOOMSNI 031403 1 Wiring loom , street washNI 031402 1 Wiring loom , tow barNI 031401 1 Wiring loom , H-P pump drive/pumpNI 031400 1 Wiring loom , RH Valeo lightsNI 031399 1 Wiring loom , LH Valeo lightsNI 031398 1 Wiring loom , chassis rear lightsNI 032646 1 Wiring loom ‘B’ , DDD specNI 032645 1 Wiring loom ‘B’ , no brush stopsNI 032643 1 Wiring loom ‘A’, hydraulics....NI 032642 1 Wiring loom, driveNI 032845 1 Cable, earth point to battery - EURO 4 (negative)NI 037773 1 Cable, earth point to battery - EURO 5 (negative)NI 032851 1 Cable, battery to cab (positive)NI 032844 1 Cable, battery to starter - EURO 4 (posative)NI 037774 1 Cable, battery to starter - EURO 5 (posative)NI 032852 1 Cable, earth point to cab (negative)NI 034965 1 Wiring loom, cab - EURO 4NI 037076 1 Wiring loom, cab - EURO 5NI 034966 2 Wiring loom, headlights NI 033120 1 Wiring loom, teal hand washNI 031885 1 Wiring sub loom, 2 speed wiperNI 032641 1 Wiring loom ‘K‘ ,ECU - EURO 4NI 037075 1 Wiring loom ‘K’, ECU - EURO 5NI 034037 1 Wiring loom, rear door & external buttonsNI 033218 1 Wiring loom, hand brake/brake lightsNI 036188 1 Cable, battery negative post to isolatorNI 036189 1 Cable, earth post to isolatorNI 031649 1 Wiring loom, load sensorNI 033993 1 Wiring loom, air conditioning - control panelNI 033997 1 Wiring loom, air conditioning - condenserNI 037742 1 Wiring loom, cooler fan regulator - EURO 5
Item Part Number Quantity Description
CANbus ELECTRICAL COMPONENTSNI 032539 2 NODE Z GA CANODE-HC-B (2 PCB)NI 033089 1 Door pod 6 button controllerNI 033088 1 Main control 23-button controller & displayNI 032427 1 Node, hydrostatic driveNI 037228 1 Controller, CR2500 - EURO 5
Item Part Number Quantity Description
ELECTRICAL COMPONENTS - In-CabNI 031599 1 Radio/CD playerNI 031745 1 Speakers, flush type NI 013749 1 Interior lightNI 028108 1 Socket 12 voltNI 013239 4 Pilot lamps (Dash board)NI 035201 1 Wiper motor
ILLUSTRATED PARTS CATALOGUE Section KSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Electrical System & Related Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
K
Item Part Number Quantity Description
ELECTRICAL COMPONENTS - SwitchesNI 032910 2 Handbrake/brake light switchNI 032627 1 Sensor, Hopper RaiseNI 036049 1 Battery isolatorNI 036187 1 . Mounting bracketNI 024066 1 Load sensor
Item Part Number Quantity Description
ELECTRICAL COMPONENTS - Head/Rear Lamps & Marker LightsNI 025506 1 Headlamp LH- LH DIP. U.KNI 025504 1 Headlamp LH- RH DIP. EuropeNI 025507 1 Headlamp RH - LH DIP. U.KNI 025505 1 Headlamp RH - RH DIP. EuropeNI 011498 As Req . Headlamp main, spare bulb 12 Volt 55 WattNI 011499 As Req . Headlamp dip, spare bulb 12 Volt 55 WattNI 011500 As Req . Headlamp sidelight, spare bulb 12 Volt 4 WattNI 028191 1 Bulb kit (France only)NI 030669 1 Rear lamp RHNI 030952 1 . Lens, rear lampNI 014677 1 . . Socket, connectorNI 030668 1 Rear lamp LHNI 030952 1 . Lens, rear lampNI 014677 1 . . Socket, connectorNI 034187 1 . Guard assembly, rear light (Optional)NI 034849 2 Turn/hazard , side indicator (complete with amber lamp)NI 035369 2 Lamp, amber, spare for side indicator
Item Part Number Quantity Description
ELECTRICAL COMPONENTS - Work Lamps, Beacons & Light barsNI 028599 As Req Work lamp 55 WattNI 004232 As Req . Bulb NI 004231 As Req . . Plug & terminalsNI 004055 As Req . . Rubber bootNI 010304 1 Beacon 12 VoltNI 011496 As Req . Bulb, spare, LLB 448NI 022097 As Req . Lens, spareNI 010297 1 . Bracket, beacon 010304NI 024173 1 Beacon bar 33”NI 028552 1 Light bar 20”NI 032721 As Req Flashing beacon, LED, 12 VoltNI 036076 1 . Attachment plate, LED beacon *
NOTE:* Only required when LED beacons are fitted in conjunction with rear direction arrow sign
Item Part Number Quantity Description
ELECTRICAL COMPONENTS - GantryNI 032985 1 Battery, 12 Volt 100 Ah, UK019 - EURO 4NI 037169 1 Battery, 12 Volt 110 Ah - EURO 5NI 034056 1 ECU - EURO 4NI 037935 1 ECU - EURO 5
NOTE:Unless stated all parts are common for EURO 4 and 5 models
K Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Electrical System & Related Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION LLABELS AND DECALS
TABLE OF CONTENTS
Assembly/Description Page
LABELSDiesel fuel oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Warning, hopper prop deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Warning, brush rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Sound level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Hydraulic oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Hydraulic oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1PM10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Engine overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Start and stopping engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Smoke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1First service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Battery boost charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Cab lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Fuse and relay information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Grab handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Coolant grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Max height. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Hazard, hot coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
DECALSScarab minor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Grill, GRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
NOTE:Unless stated all parts are common for EURO 4 and 5 models
L Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Labels and Decals Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
LABELS1 036222 1 Label, fuel grade2 022384 2 Warning, hopper prop (affixed to both sides of vehicle)3 022383 4 Warning, brush rotation (affixed to both sides of vehicle)4 021061 1 Sound level5 028760 1 Hydraulic oil6 034549 1 Hydraulic oil Level7 034814 1 PM10 (specifies year of manufacture)8 020028 1 Engine overheating
Affixed inside cab
9 022725 1 Starting and stopping engine10 014437 1 Headlamp11 024384 1 Smoke12 028623 1 First service13 032477 1 Battery boost charging14 035886 1 Cab lift15 033483 1 Fuse and relay information16 036359 1 Grab handle17 036223 1 Coolant grade18 036665 1 Max height 19 028910 1 Hazard, hot coolant
NOTE:The wording on the above labels my differ, in some cases.
IMPORTANTCORRECT PROCEDURES MUSTBE FOLLOWED WHEN STARTINGAND STOPPING ENGINE TOAVOID LASTING DAMAGE.
FOR FURTHER INFORMATIONCONSULT ENGINE INSTRUCTIONMANUAL.
STOPAND SWITCH OFF
ENGINE IF OVERHEATINGBUZZER SOUNDS
INVESTIGATE CAUSEBEFORE PROCEEDING
0.6
THESE ITEMS ARE LOCATED INSIDE CAB
REPEATED ON OPPOSITESIDE OF VEHICLE
2
2
3
5
6
7
8
9
10
12
13
14
15
11
1
4
17
16
18
19
ILLUSTRATED PARTS CATALOGUE Section LSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Labels and Decals
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
L
L Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Labels and Decals Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
DECALS1 022849 2 Scarab minor2 034786 1 Grill, GRP
Opposite side identical
ILLUSTRATED PARTS CATALOGUE Section LSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Labels and Decals
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
L
L Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Labels and Decals Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
SECTION MSTREETWASH EQUIPMENT
TABLE OF CONTENTS
Assembly/Description Page
Streetwash spray bar assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Streetwash control valve assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Streetwash diverting valve assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Control joystick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Standard & Hi-tip water bag assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
NOTE:Unless stated all parts are common for EURO 4 and 5 models
M Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR - CANbus
Streetwash Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
STREETWASH SPRAY BAR ARRANGEMENT1 014977 1 Spraybar2 014978 1 . Bracket, swivel
011259 3 . . Bolt, hex head, M12 x 130 mm long011077 3 . . Nut, M12 Nyloc
3 010901 3 . Grease nipple4 013491 3 . Sleeve5 013488 6 . Bush
NI 014979 1 . Mounting plateNI 014981 2 . Ram pivotNI 014982 2 . ClampNI 014983 2 . U clamp, 1 ”6 012973 1 . Ram, hydraulic, No 17 014984 1 . Bracket, pivot8 013495 1 . Link, lower9 013011 1 . Top link
10 014988 1 . Bracket, coupling11 010112 9 . Spray nozzle12 020027 9 . . Spray jet13 010990 2 . Hose, rubber, ” x 600 mm long, straight ends14 001100 1 . Hose, rubber, ” x 460 mm long, straight end + 90° 15 001023 1 . Hose, rubber, ” x 710 mm long, straight ends16 001220 1 . Hose, rubber, ” x 410 mm long, straight end + 90° 19 010067 6 . Pin 20 x 5020 011122 12 . Split pin, ” x 1 ”NI 011171 3 . Elbow, swivel, ” BSP M/F21 012974 2 . Ram No222 012539 3 . Restrictor No523 011241 2 . Plug ” BSP24 011152 5 . Seal, Dowty, ” BSP25 012983 4 . Coupling, quick release ” BSP26 002008 4 . Adaptor, bulkhead, ” BSP, M/MNI 011199 8 . Adaptor, ” x ” BSP, M/MNI 011153 8 . . Seal, Dowty, ” BSP27 014998 4 . Dust cap28 014999 4 . Dust cap29 012253 4 . Antiluce, smallNI 011159 1 . Adaptor, ” BSP, M/M30 011257 1 . Ball valve ” BSP
11,12
2,3,4,5719,20
29
16,25,26,27,28
STREETWASH SPRAY BAR ARRANGEMENT
1
20,21
21,22
30
8,9,10
21,22
6
13
15
14
16Behind
23,24
ILLUSTRATED PARTS CATALOGUE Section MSCARAB VM MINOR - CANbus Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Streetwash Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
M
M Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR - CANbus
Streetwash Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
CONTROL VALVE ASSEMBLY - STREET WASH KIT1 020380 1 Front mount hydraulics assembly (LH Drive)1 020381 1 Front mount hydraulics assembly (RH Drive)2 012582 2 . Valve solenoid, 12 Volt3 012874 1 . Valve solenoid, 12 Volt4 020116 1 . Mounting plate
011006 4 . . Screw, socket cap head, M6 x 70 mm long011070 8 . . Nut, hex, M6 Nyloc011014 4 . . Setscrew, hex head, M8 x 40 mm long011072 4 . . Nut, hex, M8 Nyloc011003 4 . . Setscrew, hex head, M6 x 50 mm long000028 3 . . Screw, slotted round head 2BA x ” long011078 3 . . Nut, hex, 2BA Nyloc
5 014025 12 . . Spacer6 011152 2 . Seal, Dowty ” BSP7 011153 7 . Seal, Dowty ” BSP8 011158 2 . Adaptor, ” BSP, M/M9 011199 8 . Adaptor, ” x ” BSP, M/M
10 011171 4 . Elbow, Swivel, ” BSP, M/F11 002005 4 . Tee, ” BSP, M/M/M12 010958 2.0 m . Pipe, rubber, ” bore13 010516 4 . . Hose clip, worm drive, 11 - 16 mm14 010922 2 . Hose tail, ” BSP x ” hose15 010921 1 . Hosetail, ” BSP x ” hose16 010984 3 . Hose, rubber, ” BSP x 2972 mm long, straight ends17 011317 1 . Hose, rubber, ” BSP x 295 mm long, straight ends18 010982 1 . Hose, rubber, ” BSP x 168 mm long, straight ends19 001220 1 . Hose, rubber, ” BSP x 410 mm long, straight end + 90°20 011214 3 . Adaptor, ” BSP, F/F21 023810 1 . Valve assembly ‘E’ SpoolNI 023569 1 . . Valve, control ‘E’ SpoolNI 021505 1 . . Cetop sub plateNI 010112 1 . Nozzle, brass
To
Lift
Ram
Wat
er H
ose
Stre
etw
ash
Onl
y
Test
Poi
nt
18
8
311
3,7 9
,16,2
0
19
9,1
6,2
0
2 15
6,9
6,8
11
12,1
3,1
4
7,9
10
7,9
17
4
10
7,9
Va
lve B
lock
RH
Ra
mLH
Ra
m
Lift
Ra
m
Nozz
leLi
ft R
am
21
CONTROL VALVE ASSEMBLY
Suct
ion
Noz
zle
10
11
8
Mounted on side of chassis.
ILLUSTRATED PARTS CATALOGUE Section MSCARAB VM MINOR - CANbus Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Streetwash Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
M
M Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR - CANbus
Streetwash Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
SWEEP/ WASH DIVERTER VALVE ASSEMBLY1 021810 1 Bracket, mounting2 021505 1 . Cetop sub plate
000038 4 . . Screw, socket cap head, M6 x 25 mm long011071 4 . . Nut, M6, Nyloc
3 023567 1 . Valve, control, JA Spool-One S000137 4 . . Screw, socket cap head, M5 x 50 mm long
4 011242 1 . . Plug ” BSP5 011167 1 . . Adaptor ” X ” BSP, M/M6 011153 3 . . Seal, Dowty ” BSP7 011234 1 . . Elbow, hose tail, ” BSP to ” bore8 011159 2 . . Adaptor, ” BSP, M/M9 011172 2 . . Elbow, swivel, ” BSP, M/F
Item Part Number Quantity Description
CONTROL JOYSTICK1 032813 1 Joystick2 030648 1 . Direction label
Mounted near trunnion ram (Lo-Tip)
16,8,9
5,6,7
3
4
SWEEP WASH VALVE ASSEMBLY
2
CONTROL JOYSTICK
1
2
ILLUSTRATED PARTS CATALOGUE Section MSCARAB VM MINOR - CANbus Page 6
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Streetwash Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
M
M Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR - CANbus
Streetwash Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Item Part Number Quantity Description
WATER BAG - LOW TIP ARRANGEMENT1 014859 1 Frame, low tip1 014444 1 Frame, high-tip2 014865 1 . Water bag2 014865 1 . Water bag, high-tip3 014864 4 . Hook3 014417 2 . Hook, hi-tip4 020313 2 . Hook5 014749 1 . Hose coupling, female6 014789 1 . Hose coupling, male7 010518 5 . Clamp, worm drive, 25 - 35 mm8 010959 As req . . Tube, rubber, 1” bore9 002152 1 Valve, ball, 3-way
10 011161 3 . Adaptor, ” BSP, M/M11 011156 3 . Seal, Dowty, ” BSP12 021223 1 . Strainer, water filter13 010931 2 . Hose tail, ” BSP x 1” hose14 012228 1 . Adaptor, ” BSP, M/F15 011174 1 . Elbow, swivel, ” BSP, F/F
12
3
4
5,6
6,7
8
9
10,1112
13 14,1110,11
13
15
WATER BAG - LOW TIP ARRANGEMENT
ILLUSTRATED PARTS CATALOGUE Section MSCARAB VM MINOR - CANbus Page 8
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Streetwash Equipment
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
M
M Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR - CANbus
Streetwash Equipment Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
THIS PAGE INTENTIONALLY LEFT BLANK
ILLUSTRATED PARTS CATALOGUE
SCARAB VM MINOR
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10
MULTILINGUAL GLOSSARYof
DECRIPTIONS & TERMINOLOGYused in this
PARTS CATALOGUE
N Section ILLUSTRATED PARTS CATALOGUE
1 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
ENGLISH FRANCAIS ITALIANO
AAccess Accès Accesso
Accessories Accessoires AccessoriAccelerator Accélérateur Acceleratore
Actuator Servomoteur Attuatore
Adaptor (adapt) Adaptateur (adapter) Adattatore Adaptor Flange Adaptateur à bride Flangia adattatore
Adaptor Plate Adaptateur, à plaque Piastra adattatore
Adaptor Straight Adaptateur, droit Adattatore in lineaAdjuster Régulateur Dispositivo di regolazione
Adjuster Kit Régulateur, kit Corredo dispositivo di regolazi-one
Adjuster Valve Vanne de régulation Valvola dispositivo di regolazi-one
Adjustable Ajustable RegolabileAerial Antenne Antenna
Air Air Aria
Air Cleaner Filtre à air Filtro ariaAir Conditioner Climatiseur Condizionatore aria
Air Cylinder Cylindre d’air Cilindro ariaAir Filter Filtre à air Filtro aria
Air Manifold Collecteur d’air Collettore aria
Air Mass Meter Compteur d’air-massique Flussometro di massaAir Feed Injecteur d’air Alimentazione aria
Air Chute Goulotte pneumatique Lobo aria
Air Outlet Sortie d’air Bocca di uscita ariaAir Muffler Amortisseur d’air Solemnization aria
Air Pressure Regulator Régulateur de pression d’air Regolatore pressione aria
Air Ram Vérin pneumatique Pistone ariaAir Valve Soupape d’air Valvola di sfiato
Air Vent Pipe Tuyau de refoulement d’air Tubo di sfiato
Alternator Alternateur AlternatoreAlternator Interface Alternateur, interface Interfaccia alternatore
Aluminium (Alum) Aluminium (alum) Alluminio (Allum.)
Anchor Ancre, dispositif d’ancrage AncoraAngle Angle Angolo
Antiluce Fastener Fixation « Antiluce » Dispositivo di fissaggio Antiluce
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 2
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Amendment (Amdt.) Modification (modif.) Rettifica (rett.)Amplifier Amplificateur Amplificatore
Arrangement Disposition Disposizione
Ashtray Cendrier PosacenereAssembly (Assy) Ensemble Gruppo
Auto Blanking Fermeture automatique Autochiusura
Automatic Automatique AutomaticoAuxiliary Auxiliaire Ausiliario
Axle Essieu Asse
Axle Beam Essieu, fusée d’ Asta asseAxle Bolt Essieu, boulon d’ Bullone asse
Axle Breather Essieu, reniflard d’ Sfiatatoio asse
Axle Carrier & Tube Essieu, porte-essieu et tube Supporto e tubo asseAxle Front Essieu, avant Frontale asseAxle Rear Essieu, arrière Retro asse
Axle Washer Essieu, rondelle d’ Rondella asse
BBack Plate Socle Piastra di supporto
Bag Sac BorsaBall Bille Sfera
Ball End Rotule Estremità arrotondataBall Joint Joint sphérique Giunto sferico
Ball Valve Vanne à boisseau Valvola a sferaBar Barre Barra
Basin Cuvette Bacino
Battery Batterie BatteriaBattery Housing Batterie, logement de Sede batteria
Battery Terminals Batterie, bornes Terminali batteria
Battery Lead Batterie, câble Cavo batteriaBattery Tray Batterie, plateau Vassoio portabatteria
Beacon Gyrophare Segnale luminoso
Beacon Bar Barre de gyrophare Barra segnale luminosoBeam Phare Fascio
Bearing Roulement, palier Cuscinetto
Bell Housing Logement évasé Sede campanelloBellows Soufflet Soffietto
Belt Courroie Cinghia
Black Noir NeroBlanking Obturation Tappaggio
N Section ILLUSTRATED PARTS CATALOGUE
3 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Bleeper Signal Emettitore di segnali acusticiBlind Rivet Rivet aveugle Ribattino con spina inserita
Block Bloc Blocco
Blue Bleu BluBoard Carton PiastraBody Corps Corpo
Bolt Boulon Bullonehex hd (hexagonal head) Boulon à tête 6 pans testa esagonale
skt hd (socket head) Boulon à tête creuse brugola
csk hd (counter-sunk head) Boulon à tête fraisée svasatoBoom Flèche BraccioBoost Suralimenter Spinta
Bore Alésage Camera cilindricaBoss Moyeu, bossage Mozzo
Bottom Fond Fondo
Bottle Bouteille FlaconeBox Boîte Scatola
Brace Tirant Braccio
Bracket (Brkt) Support StaffaBrake Frein Freno
Brass Wing Nut Ecrou à oreilles, en laiton Galletto di ottoneBreather Reniflard Sfiatatoio
Broom Balai Scopa
Brown Marron MarroneBrush Brosse SpazzolaBase Base Base
Buffer Tampon RespingenteBuild Construire, modèle CostruzioneBulb Ampoule Lampadina
Bulkhead Cloison ParatiaBumper Pare-chocs Paraurti
Bump Stop Butoir Respingente
Bungee Cord Corde « Bungee » Cavo elasticoBush Manchon / Bague Boccola
Buzzer Vibreur Cicalino
Button Bouton Pulsante
CCab Cabine Cabina
Cable Câble Cavo
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 4
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Caliper Calibre PinzaCam Shaft Arbre à cames Albero a camme
Camera Caméra Camera
Canopy Auvent / Capot TettuccioCap Capuchon Cappuccio
Capping Chapeau Cornice
Carabiner Carabine CarabinerCarrier Porte, support Portante
Case Boîtier Scatola
Casing Boîtier InvolucroCatalogue Catalogue Catalogo
Catch Cliquet, disp. d’arrêt Fermo
Caution Notice « attention » AttenzioneCentre Centre CentroChain Chaîne Catena
Chassis Châssis ChassisCheck Contrôle Controllo
Check Valve Soupape d’arrêt / Clapet Valvola di ritegno
Chute Goulotte ScivoloCirclip Circlip Anello elasticoCircuit Circuit Circuito
Clamp Collier MorsettoCleaner Nettoyage, dispositif de Detergente
Clevis Chape ManiglioneClip Pince Clip
Clutch Embrayage Frizione
Coach Carrosserie CarrozzeriaCoil Bobine Bobina
Collar Bague de serrage Piattello
Complete Complet (complète) CompletoComponents Composants ComponentiCompressor Compresseur Compressore
Cone Cône ConoConnector Connecteur Connettore
Connecting Connectant Connessione in corso
Connection Connexion Connessione Con Rod (Connecting Rod) Bielle Biella
Continued (Cont.) Suite Continuazione (cont.)
Control (Cntrl) Contrôle Controllo (Cntrl)
N Section ILLUSTRATED PARTS CATALOGUE
5 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Controller Contrôleur Unità di controlloConventional Conventionnel Convenzionale
Conversion (Conv) Conversion Conversione (Conv)
Cooler Refroidisseur RefrigeranteCooling Refroidissement RaffreddamentoCopper Cuivre Rame
Core Ame NucleoCotter Goupille Chiavetta trasversale
Coupling Raccord / Accouplement Accoppiamento
Cover Couvercle CoperchioCowling Capotage Cappottatura
Crank-case Carter-moteur Basamento
Cranked Contre-coudé Gambo piegatoCross Member Traverse TraversaCrown Wheal Couronne d’entraînement Corona dentata
Curb Bord, bordure BordoCylinder Cylindre Cilindro
DDamper Amortisseur Smorzatore
Deflector Déflecteur DeflettoreDescription Description Descrizione
Details Informations Dettagli
Detergent Detergent DetergenteDiagram Diagramme Diagramma
Dial Cadran Quadrante
Diaphragm Diaphragme DiaframmaDiode Diode Diodo
Dipped Beam Feu de croisement Anabbagliante
Dipstick Jauge Asta di livelloDipstick guide Jauge, guide de Guida asta di livello
Dipstick tube Jauge, tube de Tubo asta di livello
Directional Directionnel DirezionaleDirt Impureté Sporco
Disc / Disk Disque Disco
Display Écran d’affichage Visualizzatore Distributor Distributeur Distributore
Diverter Diviseur Diverter
Door Porte SportelloDouble Double Doppio
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 6
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Dowel Cheville Perno di riferimentoDown Bas Giù
Dowty Seal Joint « Dowty » Chiusura ermetica Dowty
Drag Link Tube Tube de tige directrice Tirante longitudinale comando sterzo
Drain Plug Bouchon de vidange Tappo di scarico
Drive Entraînement TrasmissioneDrive Core Entraînement, âme d’ Nucleo trasmissione
Drive Coupling Entraînement, raccord d’ Accoppiamento trasmissione
Drive Dog Entraînement, crabot d’ Innesco trasmissione Drive Flange Entraînement, bride d’ Flangia trasmissioneDrive Motor Entraînement, moteur d’ Motore principale
Drive Pump Entraînement, pompe d’ Pompa trasmissioneDrive Shaft Entraînement, arbre d’ Albero comandoDrive Tube Entraînement, tube d’ Tubo trasmissione
Dual Sweep Double balayage Curvatura doppiaDump Valve Soupape de décharge Valvola di scarico rapido
Dust Poussière Polvere
EEarth, electrical (Ground) Terre / Masse Massa
Eccentric Excentrique EccentricoElbow Coude Gomito
Electric Electrique ElettricoElectrical Electrique Elettrico
Element Elément Elemento
Enclosure Enceinte AlloggiamentoEnd Extrémité Estremità
End Plate Extrémité, plaque d’ Piastra estremità
End Cap Extrémité, chapeau d’ Cappuccio estremitàEngine Moteur Motore
Exchange Echange Scambio
Exhaust Echappement ScaricoExhaust Gas Recirculation
(EGR)Recyclage de gaz d’échap-pement
Ricircolo gas di scarico
Expansion Dilatation Espansione
Extended Dilaté EstesoExtension Extension Estensione
Extinguisher Extincteur Estintore
N Section ILLUSTRATED PARTS CATALOGUE
7 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
FFan Ventilateur Ventola
Fastener Fixation Dispositivo di fissaggioFeed Alimentation Alimentazione
Female Femelle Femmina
Filler Remplisseur Bocchettone di riempimentoFilter Filtre Filtro
Finisher Finisseur Finitore
Fire Feu CombustioneFirst Premier Primo
Fishtail Queue de poisson / Cône Coda di pesce
Fit Emboîter / Monter MontaggioFitting Raccord MontaggioFixing Fixation Rettifica
Flange Bride FlangiaFlap Volet Alettone
Flash Flash Flash
Flexible (Flexi) Flexible Flessibile (flexi)Floor Plancher Pavimento
Floorplate Plaque de sol Base pavimentoFlow Débit FlussoFluid Fluide Fluido
Flywheel Volant VolanoFoam Mousse Schiuma
Fog Brouillard Nebbia
Foot Pied PiedeForward Avant Avanti
Frame Bâti Telaio
Front Avant AnterioreFuel Carburant Combustibile
Function Fonction Funzione
Fuse Fusible Fusibile
GGain Gain Guadagno
Galvanised Galvanisé ZincatoGantry Portique Cavalletto
Gas Gaz GasGas Strut Jambe à gaz Puntone gas
Gasket Garniture d’étanchéité Guarnizione
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 8
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Gauge Manomètre CalibroGauze Gaze Garza
Gear Engrenage Ingranaggio
Geared A engrenages IngranatoGearbox Boîte de vitesses Scatola del cambioGeneral Général(e) Generale
Glass Verre VetroGlow Plug Bougie de préchauffage Spina a incandescenza
Gobbler (Nozzle Tilt) Gobbler (Inclinaison d’ Embout)
Gobbler (Ugello Inclinazione)
Grab Grappin 1. Estrattore a pinza (n)Grease Graisse Grasso
Greaser Graisseur IngrassatoreGreen vert Verde
Grey gris Grigio
Grill gril GrigliaGrip manche 1. Presa (n)
Grub Screw vis sans tête Vite di riferimento
Grommet virole Anello di tenutaGuard Carter de protection RiparoGuide Guide Guida
HHandbrake Frein à main Freno a mano
Hand Côté Mano Hand Primer Pompe à main, dispositif de Pompetta di adescamento a
manoHand Wash Lavage à main Lavaggio a mano
Handle Poignée Maniglia
Hanger Suspension Supporto pendente Harness Harnais Cablaggio
Head Tête Testa
Headlamp Phare FaroHeat Chaleur Calore
Heatshield Bouclier thermique Scudo termico
Heater Chauffage RiscaldatoreHigh-pressure Haute pression Alta pressione
Hi Tip Bennage en hauteur Punta alta
Hinge Charnière CernieraHinged Charnière, à IncernieratoHolder Porte-outil Staffa di supporto
N Section ILLUSTRATED PARTS CATALOGUE
9 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Hooks Crochets GanciHopper Trémie Serbatoio con scarico sul
fondo
Horn Avertisseur sonore Avvisatore acusticoHose Tuyau flexible Tubo flessibile
Hose Tail Tuyau flexible, bout de Raccordo tubo flessibile
Hot Chaud CaldoHour Meter Compteur horaire Contaore
Housing Logement Alloggiamento
Hub Manchon MozzoHydraulic Hydraulique Idraulico
Hydrant Bouche d’incendie Idrante
Hydrant Filler Bouche d’incendie, disp. de remplissage
Filtro idrante
Hydrant Hose Bouche d’incendie, tuyau sou-ple
Tubo idrante
Hydrostatic Hydrostatique Idrostatico
IIdentification Identification Identificazione
Idle Inactif / Ralenti InattivoIgnition (Ign) Contact Accensione (Acc)
Illuminated Eclairé Illuminato
Illustrated Illustré IllustratoIllustration Illustration Illustrazione
Impellor Rotor / Tirbine Girante
Inclusive Compris InclusivoInformation (Info) Informations Informazioni (Info)
In Entré Dentro
Inlet Entrée AmmissioneInlet Cone Entrée, cône d’ Cono di ammissione
Inlet Pipe Entrée, tuyau d’ Tubo di ammissione
Injection Pump Pompe d’injection Pompa d’iniezioneInjector Injecteur Iniettore
Injector Pipe Tuyau d’injection Tubo iniettore
Input Entrée IngressoInseal Strip Bande d’étanchéité Guarnizione sigillante
Insert Insert Inserto
Insertion Insertion InserimentoInstallation Installation InstallazioneInstrument Instrument Strumento
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 10
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Insulator Isolateur IsolanteInter Cooler Refroidisseur intermédiaire Refrigeratore intermedio
Interior Intérieur Interno
Interim Intérimaire InterimInternal Interne Interno
Item Article Articolo
JJet Jet Getto
Joint Joint GiuntoJoystick Joystick Joystick
Jubilee Clip Pince crocodile Fermaglio Jubilee
Junction Jonction Incrocio
KKey Clé Chiave
Key Switch Interrupteur à clé Interruttore a chiavettaKerb Bordure Bordo (as in pavement)
King Pin Axe-pivot Perno di sterzaggioKing Post Poinçon de faîte Puntone di sostegno
Kit Kit Corredo
Knob Bouton Manopola
LLabel EtiquetteLamp Lampe Lampada etichetta
Work Lamp Lampe de travail Lampada da lavoroHead Lamp Projecteur Faro
Side Lamp Lampe latérale Luce di posizione
Lance Lance LanciaLap Joint Joint à recouvrement Giunto a sovrapposizione
Large Grand Grande
Latch Verrou Serratura Lead Fil Cavo
L.E.D. (Light Emitting Diode) Diode électroluminescente LED (Diodo a emissione lumi-nosa)
Leash Laisse MagliaLeft Gauche Sinistra
Left Hand Drive (LHD) Conduite à gauche Guida a sinistra (LHD)Leg Jambe Gamba
Length Longueur Lunghezza
Lens Objectif Lente
N Section ILLUSTRATED PARTS CATALOGUE
11 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Level Niveau LivelloLever Levier Leva
Lid Couvercle Coperchio
Lift Ascenseur SollevareLifting Levage SollevamentoLight Feux Luce
Side Light Feux latéraux Luce di posizione Head Light Phare FaroRear Light Feu arrière Fanale di coda
Brake Light Feux stop Luce frenoInterior Light Eclairage intérieur Luce abitacolo
Fog Light Feu antibrouillard Faro antinebbia
Linch Pin Axe d’essieu AcciarinoLining Revêtement Rivestimento interno
Link Maillon Articolazione
Linkage Tringlerie Sistema di leveLitre Litre LitroList Liste Lista
Load Charge CaricoLocated Situé Posizionato
Lock Verrou FermoLocknut Ecrou de blocage ControdadoLocker Armoire Armadietto
Locking Verrouillage SerraggioLong Long Lungo
Loom Métier Cablaggio
Loop Boucle Circuito elettrico ad anelloLow Pressure Basse pression Bassa pressione
Lower Baisser Inferiore
Lubricant Lubrifiant LubrificanteLubrication Lubrification Lubrificazione
MMachine Machine MacchinaMagnet Aimant Magnete
Magnetic Magnétique MagneticoMain Principal(e) PrincipaleMale Mâle Maschio
Management Gestion GestioneManifold Collecteur Collettore
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 12
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Manual Manuel ManualeManufactured Fabriqué FabbricatoMarker Lamp Lampe signal Lampada di segnalazione
Master Maître PrincipaleMaster Cylinder Maître-cylindre Cilindro principale
Maximum (Max) Maximum (maxi) Massimo (max.)
Mesh Tamis Maglia Metal Métal MetalloMeter Mètre Calibro
Micro Switch Micro-contact MicrointerruttoreMinimum (Min) Minimum (mini) Minimo (min.)
Mirror Miroir Specchio
Miscellaneous Divers MiscellaneaModified Modifié Modificato
Module Module Modulo
Monitor Moniteur MonitorMotor Moteur MotoreMount Monture Montaggio
Mounted Monté MontatoMounting Châssis / Support Montaggio
Mud Flaps Bavettes de garde-boue Paraspruzzi
Mud Guard Garde-boue ParafangoMuffler Amortisseur Marmitta
Multi Function Multifonctions Multifunzionale
NN/A (Not Applicable) S/O (sans objet) N/D (Non disponibile)
Narrow Etroit StrettoNear side Côté trottoir Lato guida
Negative Négatif NegativoNeutral Neutre Neutro
New Nouveau (nouvelle) Nuovo
Nipple Manchon Raccordo filettatoNo Non N. (Numero)
Non Return Anti-retour Non ritorno
Normal Normal NormaleNote Note Nota
Nozzle Embout / Buse Ugello
Number Numéro NumeroNumerical Numérique Numerico
N Section ILLUSTRATED PARTS CATALOGUE
13 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Nut Ecrou DadoNyloc Nut Ecrou « Nyloc » Dado Nyloc
Hex Nut Ecrou hexagonal Dado a testa esagonale
Plain Nut Ecrou normal Dado liscioSelf Locking Nut Ecrou autobloquant Dado autobloccante
Thin Nut Ecrou mince Dado sottile
Nylon Tube Tube de nylon / Nylon, tube de Tubo di nylon
OObsolete Périmé Obsoleto
Off Arrêt 1. Spento 2. Inattivo Off Side Côté route Lato passeggero
Oil Huile OlioOlive Olive Oliva
On Marche 1. Acceso 2. Attivo
Open Ouvrir AprireOpened Ouvert(e) ApertoOpening Ouverture Apertura
Operating Fonctionnement, de OperativoOption Option Opzione
Optional Optionnel(le) OpzionaleOrange Orange ArancioneOriginal Original Originale
O-Ring Joint torique Anello di tenuta toroidaleOut Sorti(e) 1. Fuori 2. Esterno
Outer Extérieur(e) Esterno
Outlet Sortie SboccoOutput Production Uscita
Overhead Surélevé in testa
Overload Surcharge Sovraccarico
PPacker Garniture d’étanchéité Imballatore
Panel Panneau Pannello Part Pièce Ricambio
Pedal Pédale PedalePick-up Prendre / en lever Ripresa
Pilot (pressure) Pilote Pilota
Pin Cheville PernoPinion Pignon Pignone
Pink Rose Rosa
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 14
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Pipe Tuyau Tubo Piping Tuyauterie TubazionePiston Piston Pistone
Pivot Pivot Perno di testaPlastic Plastique, matière Plastica
Plate Plaque Piastra
Plinth Plinthe BasePlug Bouchon / Prise electrique Spina
Point Point Punto
Poppet Valve Soupape / Clapet Valvola supporto verticalePorts Orifices Porte
Position Position Posizione
Positioned Positionné(e) PosizionatoPost Montant Montante
Potentiometer Potentiomètre Potenziometro
Power Puissance PotenzaPneumatic (See Also Air) Pneumatique Pneumatico (vedi anche Aria)
Pressure Pression Pressione
Primer Amorce / Apprét InnescoProduction Production Produzione
Prop Support Puntello
Propshaft Arbre de transmission Albero puntelloPull Tirer Tirare
Pulley Poulie PuleggiaPulsation Pulsation Pulsazione
Pulse Impulsion Polso
Pump Pompe PompaPurple Violet Porpora
Push Pousser Spingere
QQuick Release Rapide, raccord Disinnesco rapido
RRadiator (Rad) Radiateur Radiatore (rad)
Raise Soulever SollevareRaised Soulevé(e) Sollevato
Ram Vérin Pistone
Ratio Rapport RapportoRear Arrière RetroRed Rouge Rosso
N Section ILLUSTRATED PARTS CATALOGUE
15 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Reducer Réducteur RiduttoreReducing Réduction, de Riduzione
Reduction Roue / Enrouleur Riduzione
Reel Bobine BobinaRefer Voir RiferimentoRefill Remplir Rabbocco
Regulator Régulateur RegolatoreRelated Relatif Correlato
Relay Relais Relè
Release Dégagement DisinnescoRelief Valve Soupape de sûreté Valvola di sfogo
Remote A distance / Distance, à Remoto
Repair Réparation RiparazioneReplacement Remplacement Sostituzione
Resister Résistance Resistore
Restrictor Restriction LimitatoreRetainer Retenue, dispositif de Fermo
Retaining Retenue, de Sostegno
Return Retour RitornoReverse Inverse Retromarcia
Reversing Recul Inversione di marciaRight Droite Destra
Right Hand Drive (RHD) Conduite à droite Guida a destra
Rim Jante BordoRing Bague Anello
Road Route Strada
Rod Tige AstaRolling Roulant, de roulement RotolanteRotary Rotatif Rotante
Rotate Tourner RuotareRotating Tournant RotanteRotation Rotation Rotazione
Rubber Caoutchouc Gomma
SSafety Sécurité Sicurezza
Scraper Racleur RaschiettoScreen Ecran Schermo
Screw Vis ScheggiaHex hd (hexagonal head) Vis à tête 6 pans Testa esagonale
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 16
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
skt hd (socket head) Vis à tête creuse Brugola csk hd (counter-sunk head) Vis à tête fraisée Svasata
Seal Garniture d’étanchéité Chiusura ermetica
Sealant Etanchéifiant Materiale di tenutaSealing Etanchéité, d’ Sigillante
Seat Siège Sedile
Securing Fixation, de FissaggioSelector Shaft Levier de commande Albero selettore
Self Tapping Auto-taraudeur Autofilettante
Sender Expéditeur / TransmetteurSensor Capteur Sensore
Separation Séparation Separazione
Serial Série, de SerialeService Exchange (S/EX) Echange standard Scambio di servizio
Setscrew Vis de calage Vite di fermo
Shaft Arbre AlberoShells Calandres GusciShield Ecran Scudo
Shim Cale ZeppaShock Absorber Amortisseur Ammortizzatore
Shoe Patin Scarpa
Short Court(e) GanasciaShovel Pelle Pala
Side Access Door Porte d’accès latéral Sportello accesso lateraleSight Vue Mirino
Silencer Silencieux Silenziatore
Silicon Silicone SiliconeSingle Simple Singolo
Skirt Jupe Bordatura
Slate Ardoise ArdesiaSleeve Gaine Manicotto
Slew Pivoter Ruotare
Slewing Orientation RotazioneSliding Coulissant SlittamentoSlotted Fente, A Sfinestrato
Small Petit(e) PiccoloSocket Prise Presa
Solenoid Solénoïde / Noyau Solenoide
Spacer Pièce d’espacement
N Section ILLUSTRATED PARTS CATALOGUE
17 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Spare Rechange, pièce deSpeakers Haut-parleurs
Special Spécial(e)
Speed VitesseSpherical Sphérique
Spigot Goujon / Tube de jonction
Spindle BrocheSplined CanneléSplit Pin Goupille fendue
Splitter RépartiteurSpray Pulvérisateur SpraySpring Ressort Molla
Stabilliser Stabilisateur DistanziatoreStabilising Stabilisation Ricambio
Stack Pile Altoparlanti
Standard Standard SpecialeStandpipe Colonne montante Velocità
Starter Démarreur Sferico
Steel Acier Gradino di centraggioSteering Direction Mandrino
Stiffener Raidisseur ScanalatoStop Arrêt Coppiglia
Stowage Arrimage Sdoppiatore
Straight Droit(e) Sistemazione bagagliStrap Sangle DrittoStrip Bande Cintura
Stem Tige Guarnizione Storage Rangement Stelo
Strap Attache Bagagliaio
Strut Jambe PuntoneStub Souche MozziconeStud Goujon fileté Prigioniero
Studded Barrettes, A Fissato con prigionieriStudding Colombage Fissaggio con prigionieri
Sub Frame Faux-châssis Sottotelaio
Suction Fan Turbine d’aspiration Ventola aspiranteSuction Nozzle Buse d’aspiration Ugello aspirante
Sump Carter Coppa
Supply Fourniture Alimentazione
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 18
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Support Support SupportoSuppression Suppression SoppressioneSuspension Suspension Sospensione
Sweep Balayage CurvaturaSweeping Balayant, de balayage Formatura a sagoma
Swing Balancement Oscillazione
Switch / Switches Interrupteur / Interrupteurs Interruttore / InterruttoriSwivel Pivotant Parte girevole
System Système Sistema
TTab Washer Rondelle à languettes Rondella di sicurezza
Tachograph Tachygraphe TachigrafoTachometer Tachymètre Tacometro
Tandem Tandem Tandem
Tank Réservoir SerbatoioTapered Conique Conico
Taper Lock Verrou conique Serratura conica
Tee Key Clé à béquille Chiave a TTemperature (Temp) Température (temp.) Temperatura (Temp)
Template Gabarit Sagoma
Tensioner Tendeur TensiometroTerminal Borne Terminale
Test Test TestThermostat Thermostat Termostato
Thick Epais Spesso
Thimble Dé BussolaThin Mince Sottile
Throttle Accélérateur Farfalla
Thrust Poussée SpintaTie Rod Tirant Tirante
Tilt Inclinaison Inclinazione
Tilting Inclinable InclinazioneTimer Minuterie Timer
Timing Minutage Temporizzazione
Toggle Bascule GinocchieraTool Outil Attrezzo
Toolbox Boîte à outils Cassetta attrezzi
Toothed Dentelé(e) DentatoTop Dessus Cima
N Section ILLUSTRATED PARTS CATALOGUE
19 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Tow Remorquer RimorchioTow Ball Boule de remorquage Sfera rimorchioTow Bar Barre de remorquage Barra rimorchio
Tow Point Point de remorquage Punto di rimorchioTrack Rod Barre d’accouplement Barra di accoppiamento
Trailer Remorque Rimorchio
Transfer Gearbox Boîte de transfert intermédiaire Scatola del cambio a trasferi-mento
Transmission Transmission Trasmissione
Travel Course CorsaTrunking Jonction Circuito di collegamentoTrunnion Tourillon Perno di articolazione
Tube Tube TuboTubing Tubage Tubazione
Turbocharger (Turbo) Turbocompresseur Turbocompressore
Twin Jumelé GemelloType Type Tipo
Typical Typique Tipico
Tyre Pneu Pneumatico
UUncompressed Non comprimé Decompresso
Underside Dessous Disotto
Universal Joint (U/J) Joint universel / Croisillon Giunto universaleUnion Raccord Unione
Unit Unité Unità
Un-Loader Déchargeur ScaricatoreUp Dessus Su
Update Mise à jour Aggiornamento
Usage Utilisation Utilizzo
VValve Vanne / Soupape Valvola
Variant Variante VarianteVehicle Véhicule Veicolo
Voltage Tension Voltaggio
WWander Hose Flexible aspirateur Tubo flessibile mobile
Warning Avertissement AvvertenzaWasher Rondelle Rondella
Water Eau Acqua
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 20
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Wear Usure UsuraWeed Ripper Désherbage, dispositif de Sarchiatore
Welded Soudé Saldato
Wheel Roue RuotaWhite Blanc(he) Bianco
Wide Sweep Balayage large Curvatura larga
Windscreen Pare-brise ParabrezzaWiper Essuie-glace TergicristalloWires Câblage Fili
Wiring –black,
blue,brown,green,
grey,orange,
pink,purple,
red,white
yellow
Câblage –noir,bleu,marron,vert,gris,orange,rose,violet,rouge,blancjaune
CablaggioNero, Blu, Marrone, Verde, Grigio, Arancione, Rosa, Porpora, Rosso, BiancoGiallo
Work Light Lampe de travail
XXenon Xénon Xenon
Y Yellow Jaune Giallo
Yoke Chape Forcella
N Section ILLUSTRATED PARTS CATALOGUE
21 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
ENGLISH ESPAÑOL SVENSKA
AAccess Acceso Tillgång
Accessories Accesorios TillbehörAccelerator Acelerador Gaspedal
Actuator Accionador, servomotor Aktiverare
Adaptor (adapt) Adaptador (Adapt.) ÖvergångAdapter Flange Brida del adaptador Övergångsfläns
Adaptor Plate Disco del adaptador Övergångsplatta
Adaptor, Straight Tramo recto del adaptador Rak övergångAdjuster Regulador Justering
Adjuster Kit Juego regulador Justeringssatts
Adjuster Valve Válvula del regulador VentiljusteringAdjustable Ajustable Justerbar
Aerial Antena Antenn
Air Aire LuftAir Cleaner Purificador de aire Luftrenare
Air Conditioner Aire acondicionado LuftkonditioneringAir Cylinder Cilindro de aire Luftcylinder
Air Filter Filtro de aire Luftfilter
Air Manifold Distribuidor de aire LuftfördelareAir Mass Meter Medidor de masa de aire Luftmätare
Air Feed Inyector de aire Luftförsörjning
Air Chute Conducto neumático DräneringAir Outlet Salida de aire Överskottsluft
Air Muffler Silenciador de aire Luftljuddämpare
Air Pressure Regulator Regulador de presión del aire LuftregulatorAir Ram Aire a presión Luftkolv
Air Valve Válvula de aire Luftventil
Air Vent Pipe Tubería del sistema de venti-lación
Luftventilsrör
Alternator Alternador GeneratorAlternator Interface Acoplamiento del alternador Generatorfäste
Aluminium (Alum) Aluminio (Alum.) AluminiumAnchor Anclaje Ankare
Angle Ángulo Vinkel
Antiluce Fastener Elemento de sujeción (Antiluce)
Låsbeslag(sidodörr)
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 22
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Amendment (Amdt.) Corrección (Correc.) Rättelse/förbättringAmplifier Amplificador Elektrisk förstärkare
Arrangement Disposición Arrangemang
Ashtray Cenicero AskkoppAssembly (Assy) Conjunto (Conj.) Sätta ihop
Auto Blanking Borrado automático Automatisk stängning
Automatic Automático AutomatiskAuxiliary Auxiliar Extra
Axle Eje Axel
Axle Beam Viga del ejeAxle Bolt Perno del eje Axelbult
Axle Breather Respiradero del eje
Axle Carrier & Tube Tubo y soporte del ejeAxle Front Frontal del eje FramaxelAxle Rear Trasera del eje Bakaxel
Axle Washer Arandela del eje Axelbricka
BBack Plate Contraplato Bakstycke
Bag Bolsa SäckBall Bola Kula
Ball End Lado esféricoBall Joint Rótula
Ball Valve Válvula de bola KulventilBar Barra Ramp
Basin Vasija Skål
Battery Batería BatteriBattery Housing Alojamiento de la batería Batterikåpa
Battery Terminals Bornes de la batería Batteriterminal
Battery Lead Cable de la batería BatteriblyBattery Tray Bandeja de la batería Batteri platta
Beacon Faro Varningsljus
Beacon Bar Barra del faro Takramp varningsljusBeam Haz Strålkastare
Bearing Cojinete Lager
Bell Housing Carcasa del embrague SvänghjulskåpaBellows Fuelle Bälg
Belt Correa Remm
Black Negro SvartBlanking Borrado Stängning
N Section ILLUSTRATED PARTS CATALOGUE
23 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Bleeper Emisor de tonos BackvanareBlind Rivet Remache ciego Popnit
Block Bloque Stänga/sätta igen
Blue Azul BlåBoard Tablero SkivaBody Cuerpo Kropp
Bolt Perno Bulthex hd (hexagonal head) cab. hexag. (cabeza hexago-
nal)Bult (sexkanthuvud)
skt hd (socket head) cab. hueca (cabeza hueca) Bult försänkt huvud
csk hd (counter-sunk head) cab. avell. (cabeza avel-lanada)
Boom Brazo BomBoost Empujar Högeffekt
Bore Calibre BorraBoss Refuerzo Knopp
Bottom Inferior Nertill
Bottle Botella FlaskaBox Cuadro Låda
Brace Abrazadera BandBracket (Brkt) Soporte (Sop.) Konsoll
Brake Freno Broms
Brass Wing Nut Tuerca de mariposa de latón MässingsvingmutterBreather Respiradero Luftare
Broom Escobilla Kvast
Brown Marrón BrunBrush Escobilla BorsteBase Base Bas
Buffer Amortiguador DämpareBuild Construir ByggaBulb Bombilla Lampa
Bulkhead Mampara Skott (i tank)Bumper Parachoques Kofångare
Bump Stop Tope Underkörningsskydd
Bungee Cord Cuerda elásticaBush Casquillo Bussning
Buzzer Zumbador Summer
Button Botón Knapp
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 24
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
CCab Cabina Hytt
Cable Cable WireCaliper Calibrador
Cam Shaft Árbol de levas Kamaxel
Camera Cámara KameraCanopy Cúpula Kanape
Cap Tapa Kåpa
Capping CubiertaCarabiner Mosquetón Karbidhake
Carrier Soporte Bärare
Case Caja FallCasing Carcasa Hölje
Catalogue Catálogo Katalog
Catch Fiador FångaCaution Precaución VarningCentre Centro Mitten
Chain Cadena KedjaChassis Chasis ChassieCheck Control Kontrollera
Check Valve Válvula de retención KontrollventilChute Conducto Dränering
Circlip Resorte circular BuntbandCircuit Circuito StrömkretsClamp Grapa Klämma
Cleaner Limpiador RengörareClevis Horquilla
Clip Pinza Klämma
Clutch Embrague KopplingCoach Carrocería Kaross
Coil Bobina Spole
Collar Casquillo KrageComplete Completo Slutföra
Components Componentes Komponent
Compressor Compresor KompressorCone Cono Konisk
Connector Conector Kontaktor
Connecting Conexión en curso AnslutaConnection Conexión Anslutning
N Section ILLUSTRATED PARTS CATALOGUE
25 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Con Rod (Connecting Rod) Biela (Biela)Continued (Cont.) Continuación (Cont.) Fortsatt
Control (Cntrl) Control (Cont.) Kontroll
Controller Controlador KontrollantConventional Convencional Vanlig
Conversion (Conv) Conversión (Conv.) Omställning
Cooler Refrigerador KylareCooling Refrigeración KylningCopper Cobre Koppar
Core Núcleo StommeCotter Chaveta Sprint/kil
Coupling Acoplamiento Koppling
Cover Cubierta SkyddCowling Capó
Crank-case Cárter Vevhus
Cranked Acodado KröktCross Member Travesaño TvärstagCrown Wheel Corona dentada Kronhjul
Curb Borde KanstenCylinder Cilindro Cylinder
DDamper Amortiguador Dämpare
Deflector Deflector RiktareDescription Descripción Beskrivning
Details Detalles Detaljer
Detergent Detergente RengöringDiagram Diagrama Diagram
Dial Cuadrante Ring
Diaphragm Diafragma DiafragmaDiode Diodo Diod
Dipped Beam Luz de cruce Halvljus
Dipstick Varilla de nivel de aceite Olje/mätstickaDipstick guide Guía de la varilla de nivel de
aceite Markering oljesticka
Dipstick tube Tubo de la varilla de nivel de aceite
Rör oljesticka
Directional Direccional RiktningsvisareDirt Suciedad Smutts
Disc/Disk Disco Lamell
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 26
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Display Pantalla SkärmDistributor Distribuidor Distributör
Diverter Desviador de flujo Omvändare
Door Puerta DörrDouble Doble DubbelDowel Espiga Plugg/tapp
Down Abajo NerDowty Seal Junta (Dowty)
Drag Link Tube Biela de arrastre
Drain Plug Tapón de drenaje DräneringsplugDrive Transmisión Köra
Drive Core Núcleo de la transmisión Drivaxel
Drive Coupling Acoplamiento de la transmis-ión
Drivkoppling
Drive Dog Retén de la transmisiónDrive Flange Brida de la transmisión Drivfläns
Drive Motor Motor de la transmisión DrivmotorDrive Pump Bomba de la transmisión DrivpumpDrive Shaft Eje de la transmisión Drivaxel
Drive Tube Tubo de la transmisión Dual Sweep Doble barrido Dubbelsug
Dump Valve Válvula de descarga ÖvertrycksventilDust Polvo Damm
EEarth, electrical (Ground) Tierra Jord
Eccentric Excéntrico Eccentrix
Elbow Codo VinkelElectric Eléctrico Elektrisk
Electrical Eléctrico Elektriska
Element Elemento BeståndsdelEnclosure Caja Omgivet
End Extremo Slut
End Plate Placa de tope SkyddsplattaEnd Cap Tapa de extremo Skyddskåpa
Engine Motor Motor
Exchange Intercambio VäxlaExhaust Escape Avgaser
Exhaust Gas Recirculation (EGR)
Recirculación de los gases de escape (EGR)
Avgasventil (EGR)
N Section ILLUSTRATED PARTS CATALOGUE
27 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Expansion Expansión ExpantionExtended Extendido FörlängdExtension Extensión Förlängning
Extinguisher Extintor Förlängare
FFan Ventilador Fläkt
Fastener Sujeción FästeFeed Alimentación Försörjning
Female Hembra KvinnaFiller Embudo FillerFilter Filtro Filter
Finisher Unidad de acabado AvslutareFire Fuego EldFirst Primero Första
Fishtail Cola de pezFit Acoplar Passa
Fitting Conector Montering/installation
Fixing Fijación LagaFlange Brida Fläns
Flap Aleta Dörr / öppningFlash Centelleo Blixt
Flexible (Flexi) Flexible (Flex.) Flexibel
Floor Piso GolvFloorplate Placa de piso Golvplatta
Flow Flujo Flöde
Fluid Líquido VätskaFlywheel Volante Stödhjul
Foam Espuma Skumm
Fog Niebla DimmaFoot Pie Fot
Forward Directa Framåt
Frame Bastidor RamFront Delantero FramFuel Combustible Drivmedel
Function Función FunktionFuse Fusible Säkring
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 28
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
GGain Ganancia Vinna
Galvanised Galvanizado GalvaniseradGantry Pórtico Brygga/ställning
Gas Gas Gas
Gas Strut Montante de gasGasket Junta PackningGauge Indicador Tryckmätare
Gauze Tela metálica Flor(gasbinda)Gear Engranaje Växel
Geared Accionado por engranaje Växlad
Gearbox Caja de cambios VäxellådaGeneral General I allmänhet
Glass Vidrio Glas
Glow Plug Bujía incandescente GlödstiftGobbler (Nozzle Tilt) Gobbler Tilt (stubbed)
Grab Gandhi Fånga
Grease Grassy SmartyGreaser Ingrassatore Feet
Green Verde Grön
Grey Gris GråGrill Rejilla Grill
Grip Mango GreppGrub Screw Tornillo de presión Avdragare
Grommet Arandela
Guard Protección SkyddGuide Guía Guide
HHandbrake Freno de mano Handbroms
Hand Manual, a mano Hand
Hand Primer Bomba de mano HandcremeHand Wash Lavado a mano Handtvätt
Handle Asa Handtag/vred
Hanger Soporte colgante HängareHarness Mazo de cables Sele
Head Cabeza Huvud
Headlamp Faro StrålkastareHeat Calor Värme
Heatshield Pantalla térmica Värmeplåt
N Section ILLUSTRATED PARTS CATALOGUE
29 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Heater Calentador VärmareHigh-pressure Alta presión Högtryck
Hi Tip Punta alta Högtippande
Hinge Bisagra GångjärnHinged Articulado Gångjärns hängdHolder Portaherramientas Hållare
Hooks Ganchos KrokarHopper Tolva Behållare
Horn Claxon Signalhorn
Hose Tubo flexible SlangHose Tail Extremo de tubo flexible Slangände
Hot Caliente Varm
Hour Meter Cronómetro TimräknareHousing Carcasa Kåpa/skydd
Hub Cubo Centrum
Hydraulic Hidráulico HydrauliskHydrant Boca de riego Brandpost
Hydrant Filler Brandpost huvud
Hydrant Hose Tubo flexible de la boca de riego
Brandpostslang
Hydrostatic Hidrostático Hydrostatisk
IIdentification Identificación Identifiering
Idle Ralentí IdealiskIgnition (Ign) Encendido (Enc.) Tändning
Illuminated Encendido Eliminerad
Illustrated Ilustrado IllustreradIllustration Ilustración Illustration
Impeller Propulsor Impeller
Inclusive Inclusivo InklusiveInformation (Info) Información (Info.) Information
In Dentro, entrada In
Inlet Admisión InsläppInlet Cone Núcleo de admisión Insläppskona
Inlet Pipe Tubo de admisión Insläppsrör
Injection Pump Bomba de inyección InjektionspumpInjector Inyector Injektor
Injector Pipe Tubo del inyector Injektorrör
Input Entrada Ingående
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 30
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Inseal Strip Banda de estanqueidadInsert Insertar Lägga till
Insertion Inserción Insättande/tillägg
Installation Instalación InstallationInstrument Instrumento Instrument
Insulator Aislante Isolerare
Inter Cooler Refrigerador intermedio LaddluftkylareInterior Interior InredningInterim Intermedio Interim
Internal Interno InvändigItem Elemento Punkt/artikel
JJet Chorro, inyector Jet
Joint Articulación Punkt
Joystick Palanca de control JoystickJubilee Clip Pinza (Jubilee) Slangklämma
Junction Unión Korsning
KKey Tecla Nyckel
Key Switch Interruptor de llave, llave de contacto
Tändningslås
Kerb Borde Kantsten
King Pin Pivote centralKing Post Palo macho
Kit Juego Satts
Knob Mando Knopp
Llabel Etiqueta EtikettLamp Lámpara Lampa
Work Lamp Lámpara de trabajo Arbetsljus
Head Lamp Lámpara de cabeza StrålkastareSide Lamp Lámpara lateral Positionsljus
Lance Lanza Munstycke
Lap Joint Articulación de solape FogpunktLarge Grande StorLatch Pestillo Regla/stänga
Lead Plomo, avance BlyL.E.D. (Light Emitting Diode) LED (diodo emisor de luz) L.E.D diod
Leash Correa Remm
N Section ILLUSTRATED PARTS CATALOGUE
31 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Left Izquierda VänsterLeft Hand Drive (LHD) Conducción por la izquierda
(LHD)Vänsterstyrning
Leg Pata Ben
Length Longitud LängdLens Lentes Glas
Level Nivel Nivå
Lever Palanca Spak/hävstångLid Tapa LockLift Levantar Lyfta
Lifting Levantamiento LyfterLight Luz Ljus
Side Light Luz lateral Sidoljus
Head Light Faro StrålkastareRear Light Luz trasera Bakljus
Brake Light Luz de freno Bromsljus
Interior Light Luz interior InnebelysningFog Light Luz antiniebla DimmljusLinch Pin Pasador con anilla abatible
Lining Revestimiento interior Bromsbelägg/beklädnadLink Articulación Länk
Linkage Varillaje de mando LänksystemLitre Litro LiterList Lista List
Load Carga, cargar LastaLocated Situado Placerad
Lock Cierre, bloqueo Lås
Locknut Contratuerca LäsmutterLocker Taquilla Skåp
Locking Cierre Låsa
Long Largo LångLoom Cableado eléctrico HöljeLoop Bucle Förbinda
Low Pressure Baja presión LågtryckLower Inferior, bajar Sänka
Lubricant Lubricante Smörjmedel
Lubrication Lubricación Smörjning
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 32
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
MMachine Máquina Maskin
Magnet Imán MagnetMagnetic Magnético Magnetisk
Main Principal Huvud
Male Macho ManManagement Gestión Skötsel
Manifold Distribuidor Fördelare
Manual Manual ManualManufactured Fabricado TillverkadMarker Lamp Luz de señalización
Master Principal HuvudMaster Cylinder Cilindro maestro Huvudcylinder
Maximum (Max) Máximo (Máx.) Maximum
Mesh Malla GallerMetal Metal MetallMeter Metro Meter
Micro Switch Microinterruptor MikrobrytareMinimum (Min) Mínimo (Mín.) Minimum
Mirror Espejo Spegel
Miscellaneous Varios UngefärligModified Modificado Modifierad
Module Módulo ModulMonitor Monitor, controlar Skärm
Motor Motor Motor
Mount Montura MonteraMounted Montado MonteradMounting Instalación, soporte Montera
Mud Flaps Aleta guardabarros StänkskyddMud Guard Guardabarros Stänkskärm
Muffler Silenciador Ljuddämpare
Multi Function Multifunción, multiuso Flerfunktion
NN/A (Not Applicable)
Narrow Estrecho NäraNear side Lado izquierdo Nära sidan
Negative Negativo NegativNeutral Neutral, punto muerto Neutral
New Nuevo Ny
N Section ILLUSTRATED PARTS CATALOGUE
33 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Nipple Manguito NippelNo. (Number) Número Nummer
Non Return Sin retorno Ingen återvändo
Normal Normal NormalNote Nota Not
Nozzle Boquilla Munstycke
Number Número NummerNumerical Numérico Numrerad
Nut Tuerca Mutter
Nyloc Nut Tuerca (Nyloc) NylocmutterHex Nut Tuerca hexagonal Mutter sexkant
Plain Nut Tuerca lisa Plan mutter
Self Locking Nut Tuerca autoblocante LåsmutterThin Nut Tuerca fina Mutter (tunn)
Nylon Tube Tubo de nilón Nylonslang
OObsolete Obsoleto Föråldrad
Off Apagado AvOff Side Lado derecho Vid sidan av
Oil Aceite OljaOlive Oliva Oliv
On Encendido På
Open Abrir ÖppenOpened Abierto ÖppnadOpening Apertura, abertura Öppning
Operating Funcionamiento KöraOption Opción Tillbehör
Optional Opcional Valfri/frivillig
Orange Naranja OrangeOriginal Original OrginalO-Ring Junta tórica O ring
Out (Extended) FueraOuter Exterior YttreOutlet Salida Överskott
Output Producción UtkommandeOverhead En cabeza Över huvudetOverload Sobrecarga Överlasta
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 34
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
PPacker Tapón estanco Packare
Panel Panel PanelPart Pieza Del
Pedal Pedal Pedal
Pick-up (sensor) Elegir SensorPilot (pressure) Piloto Pilot (tryck)
Pin Pasador Pinne
Pinion Piñón PinjongPink Rosa RosaPipe Tubo (rígido) Rör
Piping Tubería RördragningPiston Pistón KolvPivot Pivote Styrtapp
Plastic Plástico PlastPlate Disco, placa TallrikPlinth Base Plint
Plug Enchufe, tapón PluggPoint Punto Punkt
Poppet Valve Válvula de resorte
Ports Puertos Port/öppningPosition Posición Position
Positioned Colocado PlaceradPost Poste, borna Stolpe/stötta
Potentiometer Potenciómetro Potensiometer
Power Potencia StrömPneumatic (See Also Air) Neumático (véase también
Aire)Pneumatisk
Pressure Presión Tryck
Primer Cebador PrimerProduction Producción Produktion
Prop Apoyo Stöd/palla under
Propshaft Árbol de transmisión KardanaxelPull Tirar, tracción Drag
Pulley Polea Remskiva
Pulsation Pulsación PulserandePulse Pulso Puls
Pump Bomba Pump
Purple Púrpura Lila
N Section ILLUSTRATED PARTS CATALOGUE
35 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Push Empujar, empuje Tryck
QQuick Release Suelta rápida Snabbkoppling
RRadiator (Rad) Radiador (Rad.) Kylare
Raise Levantar LyftaRaised Levantado Lyft
Ram Pistón KolvRatio Relación RadieRear Trasero Bak
Red Rojo RödReducer Reductor Reducerare
Reducing Reducción, reduciendo Reducera
Reduction Reducción ReduceringReel Carrete Hjul
Refer Ver Referera
Refill Rellenar ÅterfyllaRegulator Regulador Regulator
Related Relacionado BesläktadRelay Relé Relä
Release Liberación Lösgöra
Relief Valve Válvula de descarga ÖvertrycksventilRemote Remoto Mottagare
Repair Reparar Reparera
Replacement Sustitución ErsättaResister Registrar, registro Motstånd
Restrictor Estrangulador Strypning
Retainer Fiador FörskottshyraRetaining Retención
Return Retorno Återvända
Reverse Inverso BackaReversing Inversión Backa
Right Derecha Höger
Right Hand Drive (RHD) Conducción por la derecha (RHD)
Högerstyrd
Rim Llanta Kant/falsRing Anillo Ring
Road Carretera VägRod Varilla Rulle
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 36
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Rolling Rodamiento RullandeRotary Giratorio, rotativo RoterandeRotate Girar Rotera
Rotating Giratorio, rotativo RoteraRotation Giro RotationRubber Goma Gummi
SSafety Seguridad Säkerhet
Scraper Escariador SkrapaScreen Filtro, pantalla GallerScrew Tornillo Skruv
csk hd (counter-sunk head) Cab. avell. (cabeza avel-lanada)
Hex hd (hexagonal head) Cab. hexag. (cabeza hexag-onal)
Skruv sexkant
skt hd (socket head) Cab. hueca (cabeza hueca) Skruv (fösänkt)
Seal Junta TätningSealant Sellante Flytande tätningmedelSealing Sellado Täta
Seat Asiento SäteSecuring Fijación Säkra
Selector Shaft Eje selector VäljaraxelSelf Tapping Aterrajado automático Självdränerande
Sender Conmutador selector Sändare
Sensor Sensor SensorSeparation Separación Separerat
Serial Serie Serie
Service Exchange (S/EX) Intercambio de servicio UtbytesdelSetscrew Tornillo de fijación Sättskruv
Shaft Eje Skaft
Shells Cuerpos SnäckorShield Protector Skjöld
Shim Suplemento Shims
Shock Absorber Amortiguador StötdämpareShoe Zapata SkoShort Corto Kort
Shovel Pala SkyffelSide Access Door Puerta de acceso lateral Sidodörr
Sight Vista Sikt
N Section ILLUSTRATED PARTS CATALOGUE
37 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Silencer Silenciador LjuddämpareSilicon Silicona SilikonSingle Único, sencillo Enkel
Skirt Faldón KjolSlate Pizarra
Sleeve Manguito Muff
Slew Pivotar Svänga/sliraSlewing Pivotaje Svängande/slirandeSliding Deslizamiento Glidande
Slotted Ranurado SpräcktSmall Pequeño Liten
Socket Casquillo Sockel
Solenoid Solenoide SolenoidSpacer Separador Distans
Spare Repuesto Reserv
Speakers Altavoces HögtalareSpecial Especial SpecialSpeed Velocidad Fart
Spherical Esférico KlotformigSpigot Espiga Rör
Spindle Husillo SpindelSplined Acanalado Flisad/splittradSplinter Partícula Skärva/splitter
Split Pin Chaveta hendida LåspinneSplitter Separador FördelareSpray Pulverizador, rociador Spaya
Spring Muelle FjäderStabiliser Estabilizador Stabiliserare
Stabilising Estabilización Stabilisera
Stack Pila Fullpropad medStandard Estándar Standard
Standpipe Tubo vertical Vattenpost
Starter Motor de arranque StartmotorSteel Acero Stål
Steering Dirección Styrning
Stem Vástago StoppaStiffener Contrafuerte, larguero Förtjockare
Stop Parar Stopp
Storage Almacenamiento Lagra
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 38
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
Stowage Estiba StuvningsutrymmeStraight Recto Rakt
Strap Tira de sujeción Sätta fast
Strip Banda Ta bortStrut Puntal Balk/stöttaStub Tope Stump/talong
Stud EspárragoStudded Con pasadorStudding Pasante
Sub Frame Bastidor auxiliar UnderramSuction Box Caja de succiónSuction Fan Ventilador de succión Sugfläkt(turbin)
Suction Nozzle Boquilla de succión SugmunstyckeSump Sumidero Oljetråg
Supply Suministro Förse
Support Asistencia, soporte StödjaSuppression Supresión UndertryckSuspension Suspensión Fjädring
Sweep Barrido SopaSweeping Barrido, barriendo Sopa
Swing Oscilación Svänga
Switch Interruptor BrytareSwitches Interruptores Brytare
Swivel Giratorio SvängbarSystem Sistema System
TTab Washer Arandela con lengüeta
Tachograph Tacógrafo Färdskrivare
Tachometer Tacómetro HastighetsmätareTandem Tándem Tandem
Tank Tanque Tank
Tapered Cónico AvsmalnandeTaper Lock Cierre cónico Plugg
Tee Key Llave en T Gren
Temperature (Temp) Temperatura (Temp.) TempraturTemplate Plantilla MallTensioner Tensor Sträckare
Terminal Terminal TerminalTest Prueba Test
N Section ILLUSTRATED PARTS CATALOGUE
39 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
Thermostat Termostato TermostatThick Espeso Tjock
Thimble Dedal Fingerborg
Thin Delgado SmalThrottle Regulador de gases Trottel
Thrust Empuje Tryck
Tie Rod Barra de acoplamiento trans-versal de la dirección
Tilt Inclinar TiltTilting Inclinación Tilta
Timer Temporizador TimerTiming Sincronización Tids anpassaToggle Báscula Vippa
Tool Herramienta VerktygToolbox Caja de herramientas VerktygslådaToothed Dentado Signalhorn
Top Superior ToppTow Remolque Dra / bogsera
Tow Ball Bola de remolque Dragkula
Tow Bar Barra de remolque DragkrokTow Point Punto de remolque Dragpunkt
Track Rod Tirante transversalTrailer Remolque Släp
Transfer Gearbox Caja de cambios transferen-cia, caja transfer
Tillsattsväxellåda
Transmission Transmisión TransmissionTravel Recorrido, viaje Resa
Trunking Unión
Trunnion MuñónTube Tubo Rör
Tubing Sistema de tuberías Rördragning
Turbocharger (Turbo) Turbocompresor (Turbo) TurboTwin Gemelo, bimotor DubbelType Tipo Typ
Typical Típico TypiskTyre Neumático Däck
ILLUSTRATED PARTS CATALOGUE Section NSCARAB VM MINOR Page 40
Manual Number Z036776 / Issue: Amdt.1 - 11/8/10 Multilingual Glossary
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
N
UUncompressed No comprimido Okomprimerad
Underside Inferior UndersidaUniversal Joint (U/J) Junta cardánica (U/J) Knutkors
Union Unión Förena
Unit Unidad DelUn-Loader Descargador Avlastning
Up Arriba Upp
Update Actualizar UppdateraUsage Uso Andvändning
VValve Válvula Ventil
Variant Variante Variant
Vehicle Vehículo FordonVoltage Tensión Volt
WWander Hose Tubo flexible móvil Sugslang (lövsug)
Warning Advertencia Varning
Washer Arandela BrickaWater Agua Vatten
Wear Desgaste SlitageWeed Ripper Escardador Ogräs
Welded Soldado Svetsad
Wheel Rueda HjulWhite Blanco Vit
Wide Sweep Barrido amplio Vals
Windscreen Parabrisas VindrutaWiper Limpiaparabrisas TorkareWires Cables Ledningar
Wiring Cableado LedningsdragningBlack,
Blue,Brown,Green,
Grey,Orange,
Pink,Purple,
Red,White
Yellow
Negro,Azul,Marrón,Verde,Gris,Naranja,Rosa,Púrpura,Rojo,BlancoAmarillo
SvartBlåBrunGrönGråOrangeRosaLilaRödVitGul
Work Light Lámpara de trabajo Arbetsljus
N Section ILLUSTRATED PARTS CATALOGUE
41 Page SCARAB VM MINOR
Multilingual Glossary Manual Number Z036776 / Issue: Amdt.1 11/8/10
When ordering replacement parts, always give the machine’s Serial Number and specify Part Number, Quantity & Description
XXenon Xenón Xenon
Y Yellow Amarillo Gul
Yoke Horquilla Sammankoppla