Indian Standards Available in Library S.No. IS No. Part /Sec Year Rev. Amd. Title of Standard 1 1 1968 2nd 2 Specification for the National Flag of India (Cotton Khadi) 2 2 1960 Rules for Rounding off Numerical Values 3 5 1994 4th Colours for Ready Mixed Paints and Enamels 4 6 1983 4th Specification for Moderate Heat duty fireclay refractories, group 'A' 5 8 1983 4th Specification for High Heat Duty Fireclay Refractories 6 25 1979 3rd Specification for Antifriction Bearing Alloys 7 28 1985 4th Specification for Phosphor Bronze Ingots and Castings 8 191 1 to 10 1980 3rd Specification for Copper 9 195 1991 3rd Fireclay Mortar for Laying Fireclay Refractory Bricks 10 207 1964 Specification for Gate and Shutter Hooks and Eyes 11 210 1993 4th Grey Iron Castings - Specification 12 228 1 1987 3rd Determination of Carbon by Volumetric method 13 228 2 1987 3rd Determination of Manganese in plain-carbon and low alloy steels by arsenite method 14 228 3 1987 3rd Determination of Phosphorus by alkalimetric method 15 228 4 1987 3rd Determination of total carbon by gravimetric method 16 228 5 1987 3rd Determination of nickel by Dimethylglyoxime 17 228 6 1987 3rd Determination of Chromium by Persulphate oxidation method 18 228 13 1982 Determination of Arsenic 19 276 1978 3rd Specification for Austenitic Manganese Steel Castings 20 277 2003 6th Galvanized Steel Sheets (plain and corrugated)-Specification 21 292 1983 2nd Specification for Leaded Brass Ingots and Castings 22 304 1981 2nd Specification for High Tensile Brass Ingots and Castings 23 305 1981 2nd Specification for Aluminium Bronze Ingots and Castings 24 306 1983 3rd Specification for Tin Bronze Ingots and Castings 25 318 1981 2nd Specification for leaded Tin Bronze Ingots and Castings 26 319 1989 4th Free Cutting leaded brass bars, rods and sections-specification 27 320 1980 2nd Specification for High Tensile Brass Rods and Sections 28 325 1978 4th Specification for Three phase induction Motors 29 341 1973 1st Specification for Black Japan, Types A, B and C 30 383 1970 2nd Specification for Coarse and fine aggregates from natural sources for concrete 31 398 3 1976 2nd Specification for Aluminium conductors for overhead transmission purposes 32 412 1975 2nd Specification for Expanded metal steel sheets for general purposes 33 446 1987 4th Specification for Rubber air hose 34 451 1972 2nd Technical Supply Conditions for Wood Screws 35 456 2000 4th 1 Code of practice for plain and reinforced concrete 36 513 1994 4th Cold rolled low carbon steel sheets and strips - specification
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
1 1 1968 2nd 2 Specification for the National Flag of India (Cotton Khadi) 2 2 1960 Rules for Rounding off Numerical Values
3 5 1994 4th Colours for Ready Mixed Paints and Enamels
4 6 1983 4th Specification for Moderate Heat duty fireclay refractories, group 'A'
5 8 1983 4th Specification for High Heat Duty Fireclay Refractories
6 25 1979 3rd Specification for Antifriction Bearing Alloys
7 28 1985 4th Specification for Phosphor Bronze Ingots and Castings
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
100 1255 1983 2nd Code of practice for installation and maintenance of power cables
up to and including 33 KV ratings 101 1261 1959 Code of practice for seam welding in mild steel
102 1271 1985 1st Thermal evaluation and classification of electrical insulation
103 1284 1975 2nd Specification for Wrought Aluminium Alloy Bolt and Screw Stock (For General Engineering Purposes)
104 1315 1977 1st Method for determination of Linear density of yarns spun on cotton system
105 1361 1978 1st Specification for steel windows for industrial buildings
106 1363 1 1992 3rd Hexagon head bolts, screws and nuts of product grade C Part-1 hexagon head bolts (size range M5 to M 64) (=ISO 4016 : 1988)
107 1363 2 1992 3rd Hexagon head screws (size range M5 to M64)
108 1363 3 1992 3rd Hexagon nuts (size range M5 to M64)
109 1364 1 1992 3rd Hexagon head bolts, screws and nuts of product grades A & B Part-2: hexagon head bolts (size range M1.6 to M64) =ISO 4014:1988
110 1364 2 1992 3rd Hexagon head screws (size range M1.6 to M64)
111 1364 3 1992 3rd Hexagon nuts (size range M1.6 to M64)
112 1364 4 1992 3rd Hexagon thin nuts (size range M1.16 to M64)
113 1364 5 1992 3rd Hexagon thin nuts unchamfered (size range M1.16 to M10)
114 1365 1978 3rd 1 Specification for slotted countersunk head screws
115 1366 1982 2nd Specification for slotted cheese head screws
116 1367 1 1980 2nd Technical supply conditions for threaded steel fasteners Part-1: introduction and general information
117 1367 2 1979 2nd Product grades and tolerances
118 1367 3 1991 3rd Mechanical properties and test methods for bolts, screws and studs with full loadability
119 1367 5 1980 Technical Supply Conditions for Threaded Steel Fasteners, Mechanical Properties and Test Methods for Set Screws and Similar Threaded Fasteners Not Under Tensile Stresses
120 1367 6 1980 2nd Mechanical properties and test methods for nuts with specified proof loads
121 1367 7 1980 Technical Supply Conditions for Threaded Steel Fasteners, Mechanical Properties and Test Methods for Nuts Without Specified Proof Loads
122 1367 8 1992 2nd Mechanical and performance properties for prevailing torque type steel hexagon nuts
123 1367 9/S-1 1993 3rd Surface discontinuities, Bolts, screws and studs for general applications
124 1367 9/S-2 1993 3rd Surface discontinuities, Bolts, screws and studs for special applications
125 1367 10 1979 2nd Surface discontinuities on nuts
126 1367 12 1981 2nd Phosphate coatings on threaded fasteners
and Mode of Delivery 131 1368 1987 3rd Dimensions for ends of parts with external ISO metric threads
=ISO 4753:1983 132 1369 1 1993 3rd Fasteners-thread run-outs and undercuts Part-1 dimensions for
screw thread run outs for external ISO metric threads 133 1369 2 1993 3rd Dimensions for screw thread undercuts for external ISO metric
threads 134 1369 3 1995 3rd Dimensions for screw thread run-outs and undercuts for internal
threads 135 1387 1967 2nd General Requirements for the Supply of Metallurgical Materials
136 1391 2 1992 2nd Room air conditioners Part-2 split air conditioners
137 1395 1982 3rd Specification for low and medium alloy steel covered electrodes for manual metal arc welding
138 1408 1968 1st Recommended procedure for inspection of copper base alloy sand castings
139 1447 3 1992 1st Petroleum and its products-methods of sampling Part-3 method of sampling of semi solid and solid petroleum products
140 1458 1965 Revd Specification for railway bronze ingots and castings
141 1477 1 1971 1st Code of practice for painting of ferrous metals in buildings part-1 pretreatment
142 1477 2 1971 1st Painting
143 1500 1983 2nd Method for brinell hardness test for metallic materials
144 1523 1972 1st Specification for bottom pouring refractories for steel plants
145 1524 1968 1st Specification for refractory sleeves
146 1525 1968 1st Specification for ladle refractories for steel plants
147 1527 1972 1st Methods for chemical analysis of high silica refractory materials
148 1528 1 1980 2nd Methods of sampling and physical tests for refractory materials Part-1 determination of pyrometric cone equivalent or softening point
149 1528 2 1974 1st Determination of refractoriness under load
150 1528 3 1983 2nd Determination of spalling resistance
152 1528 5 1993 2nd Determination of modulus of rupture at ambient temperature
153 1528 6 1974 1st Determination of permanent change after reheating
154 1528 7 1974 1st Methods of sampling and criteria for conformity
155 1528 8 1974 1st Determination of apparent porosity
156 1528 9 1995 3rd Determination of specific gravity and true density
157 1528 10 1974 1st Determination of size of refractory bricks
158 1528 11 1993 2nd Determination of war page
159 1528 12 1974 1st Determination of bulk density
160 1528 13 1974 1st Determination of resistance to the disintegrating effect of carbon monoxide
161 1528 14 1974 1st Determination of sieve analysis
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
162 1528 15 1993 Determination of modulus of rupture at elevated temperature
163 1528 16 1991 Determination of thermal conductivity upto 12500 C of dense and insulating refractory products according to the hot wire parallel method
164 1528 17 1993 Determination of cold crushing strength of shaped insulating refractory products
165 1528 18 1993 Determination of creep in compression
166 1528 19 1991 Determination of thermal expansion
167 1529 1971 1st Specification for blast furnace refractories for steel plants
168 1538 1993 3rd Cast iron fittings for pressure pipes for water, gas and sewage - specification
169 1545 1994 3rd Solid drawn copper and copper alloy tubes for condensers and heat exchanges - specification
170 1554 2 1988 2nd Specification for PVC insulated (Heavy duty) electric cables Part-2: for working voltages from 3.3 KV up to and including 11 KV
171 1570 1 1978 1st Schedules for wrought steels Part -1: steels specified by tensile and/or yield properties
172 1570 2/1 1979 1st Carbon steels (unalloyed steels), Wrought Products (other than wires) with specific chemical composition and properties
173 1570 2/2 1987 1st Carbon steels (unalloyed steels), Carbon steel wires with related properties
191 1821 1987 3rd Dimensions for clearance holes for bolts and screws(=ISO 273:1979)
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
192 1852 1985 4th 1 Specification for rolling and cutting tolerances for hot-rolled steel
products 193 1856 1977 2nd Specification for steel wire ropes for haulage purposes
194 1862 1975 2nd Specification for studs
195 1864 1979 1st Specification for hot rolled steel 'L' sections for shipbuilding
196 1865 1991 3rd Iron castings with spheriodal or nodular graphite - specification
197 1870 1965 Comparison of Indian and overseas standards for wrought steels for general engineering purposes
198 1871 1 1987 1st Commentary on Indian standard schedules for wrought steels Part-1: Steels specified by tensile and/or yield properties (complementary to IS 1570 part-1-1978)
226 2016 1967 1st 4 Specification for plain washers
227 2026 1 1977 1st 3 Specification for power transformers Part-1: general
228 2026 2 1977 1st Temperature-rise
229 2026 3 1981 2nd Insulation levels and dielectric tests
230 2026 4 1977 1st Terminal markings, tappings and connections
231 2026 5 1994 Transformer/reactor bushings-minimum external clearance in air-specification
232 2041 1995 2nd Specification for steel plates for pressure vessels used at moderate and low temperature
233 2042 1972 1st 1 Specification for insulating bricks
234 2043 1984 1st Specification for siliceous fireclay refractories
235 2048 1983 2nd 1 Specification for parallel keys and keyways
236 2062 1999 5th Steel for general structural purposes-specification
237 2063 1988 1st Acceptance code for machine tools-geometric accuracy of machines operating under No-load or finishing conditions (=ISO 230/1:1986)
238 2071 1 1993 2nd High voltage test techniques Part-1: general definitions and test requirements (=IEC Pub 60-1:1989)
239 2071 2 1974 1st Test procedures
240 2071 3 1976 1st Measuring devices
241 2074 1992 2nd 1 Ready mixed paint, air drying, red oxide zinc chrome, priming-specification
242 2102 1 1993 3rd General tolerances Part-1: tolerances for linear and angular dimensions without individual tolerance indication (=ISO 2768-1:1989)
243 2122 2 1991 1st Power transmission-belts-code of practice for selection, storage, installation and maintenance of belting for power transmission Part-2: V-belt drives
244 2148 1981 2nd 2 Specification for flameproof enclosures of electrical apparatus
245 2155 1982 1st 1 Specification for cold forged solid steel rivets for hot closing (6 to 16 mm diameter)
270 2417 1977 1st Glossary of terms relating to ultrasonic testing
271 2429 1 1987 3rd Specification for round steel short link chains (electric butt welded), grade (3) Part-1: Non-calibrated load chain for lifting purposes
272 2458 1965 2 Glossary of terms for toothed gearing
273 2458 2 1984 Bevel and hypoid gears
274 2467 1963 Notation for toothed gearing
275 2482 1990 2nd Light duty water suction hose of rubber-specification
276 2486 3 1974 Specification for insulator fittings for overhead power lines with a nominal voltage greater than 1000volts Part-3: locking devices
277 2486 4 1981 Tests for locking devices
278 2500 1 1992 2nd Sampling inspection procedures Part-1: Attribute sampling plans indexed by acceptable quality level for lot-by-lot inspection
279 2500 2 1965 1 Inspection by variables for percent defective
280 2500 3 1995 Attribute sampling plans indexed by limiting quality for isolated lot inspection (=ISO 2859-2:1985)
281 2507 1975 1st Specification for cold-rolled steel strips for springs
282 2585 1968 1st Specification for Black Square Bolts and Nuts (Dia Range 6 to 39mm) and Black Square Screws (Dia Range 6 to 24mm)
283 2591 1982 2nd Dimensions for Hot Rolled Steel Bars for Threaded Components
284 2595 1978 1st Code of practice for radiographic testing
285 2598 1966 Safety code for industrial radiographic practice
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
286 2609 1972 1st Specification for Coach Bolts
287 2611 1964 Specification for carbon chromium molybdenum steel forgings for high temperature service
288 2633 1986 2nd 1 Method for testing uniformity of coating on zinc coated articles
289 2636 1972 1st Specification for wing nuts
290 2637 1991 1st Steel roller chains, types S and C, attachments and chain wheels (=ISO 487:1984)
291 2638 1974 1st Specification for flat split cotters
292 2643 2 1975 1st 1 Dimensions for pipe threads for fastening purposes Part-2: tolerances
293 2644 1994 4th High strength steel castings for general engineering and structural purposes - specification
294 2678 1987 2nd Dimensions and tolerances for wrought aluminium and aluminium alloy drawn round tube
295 2687 1975 1st Specification for Cap Nuts
296 2705 1 1992 2nd Current transformers-specification Part-1: general requirements
297 2705 3 1992 2nd Protective current transformers
298 2705 4 1992 2nd Protective current transformers for special purpose applications
299 2707 1996 4th Carbon steel castings for surface hardening
300 2708 1993 3rd 1.5 percent manganese steel castings for general engineering purposes-specification
301 2712 1998 3rd Gaskets and packings-compressed asbestos fibre jointings-specification
302 2749 1974 1st Specification for austenitic iron castings
303 2758 1969 Specification for mild steel point hooks for use with wire rope thimbles
304 2759 1969 Specification for higher tensile steel point hooks for use with wire rope thimbles
305 2760 1980 1st 1 Specification for steel chain slings
306 2762 1982 1st Specification for wire rope slings and sling legs
307 2805 1964 Dimensions for ball grips
308 2811 1987 1st Recommendations for manual tungsten inert-gas arc welding of austenitic stainless steel
309 2825 1969 Code for unfired pressure vessels (Kept in loose)
310 2830 1992 2nd Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes-specification (superseding IS 6914:1978)
311 2831 2001 3rd Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into low tensile structural steel-specification (superseding IS 6915:1978)
312 2856 1999 4th Carbon steel castings for pressure containing parts suitable for fusion welding - specification
313 2878 1986 2nd 1 Specification for fire extinguisher, carbon dioxide type (portable and trolley mounted)
314 2890 1983 1st Specification for taper handles for machine tools
315 2904 1998 1st Ball handles-specification
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
316 2907 1964 Specification for Non-Ferrous Rivets (1.6 to 10mm)
317 2951 1 1965 Recommendation for estimation of flow of liquids in closed conduits Part-1: head loss in straight pipes due to frictional resistance
318 2951 2 1965 Head loss in valves and fittings
319 2995 1965 Dimensions for Set Collars
320 2998 1982 1st Specification for Cold Forged Steel Rivets for Cold Closing (1 to 16mm Diameter)
321 3005 1 1979 1st Specification for grey cast iron ingot moulds, stools and slag ladles Part-1: bottom stools for large size ingot moulds weighting 8 tonnes and higher
322 3005 2 1979 1st Grey cast iron ingot moulds of mass more than eight tonnes
323 3005 3 1982 1st Grey cast iron ingot moulds of mass more than one tonne and upto eight tonnes
324 3005 4 1984 1st Grey cast iron ingot moulds of mass upto 1 tonne
325 3038 1992 3rd Martensitic stainless steel and alloy steel castings for pressure containing parts suitable for high temperature service - specification
326 3042 1965 Specification for single faced sluice gates
428 4218 3 1976 1st ISO metric screw threads Part-3: basic dimensions for design profiles
429 4218 4 1976 1st Tolerancing system
430 4225 1979 1st Recommended practice for straight beam ultrasonic testing
431 4257 2 1986 Dimensions for clamping arrangements for porcelain transformer bushings Part-2: for 72.5 kv and 123 kv bushings
432 4260 1986 2nd Recommended practice for ultrasonic testing of butt welds in ferritic steel
433 4289 1 1984 1st Specification for flexible cables for lifts and other flexible connections
434 4291 1967 Dimensions for C-Washers
435 4292 1984 1st Specification for strap clamps
436 4293 1984 2nd Specification for U-type clamps
437 4297 1967 Dimensions for Spherical Washers and Conical Seats
438 4298 1967 Dimensions for Swing C-Washers
439 4326 1993 2nd Earthquake resistant design and construction of buildings - Code of practice
440 4367 1991 1st 1 Alloy steel forgings for general industrial use
441 4432 1988 1st Specification for case hardening steels
442 4460 1967 2 Method for rating of machine cut spur and helical gears
443 4475 1 1986 2nd Specification for crane-suspended ladles for foundries Part-1: straight/taper sided geared ladles 0.25 to 10 tonnes for iron and steel foundries
444 4475 2 1986 2nd Cylindrical geared ladles 0.25 to 3.0 tonnes for iron foundries
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
445 4475 3 1989 2nd Straight/taper sided ladles 0.25 to 3.0 tonnes for S.G. iron foundries
446 4475 4 1988 2nd Taper sided non-geared ladles 15 to 50 tonnes capacities for iron and steel foundries
447 4499 1968 Dimensions for Depth of Holes for Studs
448 4522 1986 2nd Specification for heat resistant alloy steel and nickel base castings
449 4594 1968 Code of practice for design of portal and semi-portal wharf cranes (electrical)
450 4601 1 1968 Navigation lights for large sea-going power driven vessels Part-1: positioning and screening of lights
459 4732 1968 Specification for Rivets for Shipbuilding
460 4740 1979 1st Code of practice for packaging of steel tubes
461 4762 1984 1st 4 Specification for worm drive hose clamps for general purposes
462 4794 1 1968 Specification for push button switches Part-1: general requirements and tests
463 4794 2 1986 1st Push button switches type 1
464 4853 1982 1st Recommended practice for radiographic inspection of fusion welded butt joints in steel pipes
465 4854 1 1969 Glossary of terms for valves and their parts Part-1: screw-down stop, check and gate valves and their parts
466 4854 2 1968 Plug valves and cocks and their parts
467 4854 3 1974 Butterfly valves
468 4864* 1968 Specification for shell flanges for vessels and equipment: general requirements
469 4865* 1968 Specification for shell flanges for vessels and equipment : welded shell flanges for non-pressure service
470 4866* 1968 Specification for shell flanges for vessels and equipment : welded shell flanges for carbon steel pressure vessels and equipment
471 4867* 1968 Specification for shell flanges for vessels and equipment : welded neck shell flanges for carbon steel for pressure vessels and equipment
472 4868* 1968 Specification for shell flanges for vessels and equipment : welded shell flanges for stainless steel pressure vessels and equipment
473 4869* 1968 Specification for shell flanges for vessels and equipment : welded shell flanges with hub for stainless steel pressure vessels and equipment
474 4870* 1968 Specification for shell flanges for vessels and equipment : flat gaskets for shell flanges
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
475 4882 1979 1st Specification for Low Carbon Steel Wire for Rivets for use in
Bearing Industry 476 4896 1992 2nd One percent chromium steel castings for resistance to abrasion-
specification 477 4897 1994 3rd Deviations on untoleranced dimensions and mass of steel castings
478 4898 1989 2nd Steel castings for case carburizing-specification
479 4904 1990 3rd Calibration blocks for use in ultrasonic non-destructive testing-specification
480 4923 1997 2nd 1 Hollow steel sections for structural use
481 4981 1984 2nd Specification for Guide Pins for Foundry Pattern Plates
482 5037 1969 Specification for basic rack and modules of straight bevel gears for general engineering and heavy engineering
483 5053 1969 Dimensions for Wrought Copper and Copper Alloy Rods for Fasteners
484 5096 1969 Dimensions for round locating studs
485 5097 1969 Dimensions for diamond locating studs
486 5108 1969 Recommendation on nominal rates of flow for oil-hydraulic system elements
487 5120 1977 1st 3 Technical requirements for rotodynamic special purpose pumps
488 5129 1 2000 3rd Rotary shaft lip type seals Part-1: nominal dimensions and tolerances
489 5129 2 2003 3rd Vocabulary
490 5129 3 2000 Storage, handling and installation
491 5129 4 2000 Performance test procedures
492 5129 5 2000 Identification of visual imperfections
493 5206 1983 1st Specification for covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels
494 5267 1969 Glossary of terms for worm gears
495 5312 1 1984 1st Specification for swing check type reflux (non-return) valves for water works purposes Part-1: single door pattern
496 5312 2 1986 Multi-door purpose
497 5334 1981 1st Code of practice for magnetic particle flaw detection of welds
498 5368 1969 Specification for thin slotted and castle nuts (dia range 6 to 52 mm)
499 5369 1975 1st General requirements for plain washers and lock washers
500 5370 1969 Dimensions for Plain Washers with Outside Diameter ~ 3 x Inside Diameter
501 5371 1982 1st Specification for multi-tooth lock washers
502 5372 1975 1st Specification for taper washers for cahnnels (ISMC)
503 5373 1969 Specification for square washers for wood fastenings
504 5374 1975 1st Specification for taper washers for I-beams (ISMB)
505 5504 1997 1st Specification for spiral welded pipes
506 5517 1993 2nd Steels for hardening and tempering-specification
507 5530 1987 1st Recommendations for production, rectification and repair of steel castings by metal arc welding process
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
508 5554 1970 Specification for lock washers with LUG
509 5556 1970 Specification for Fan Disc Washers
510 5612 1 1977 1st 1 Specification for hose-clamps and hose-bandages for fire brigade use Part-1: hose-clamps
511 5612 2 1977 1st Hose-bandages
512 5620 1985 2nd Recommendations for structural design criteria for low head slide
513 5624 1993 1st Foundation bolts - specification
514 5743 1991 1st Copper master alloys
515 5788 1986 1st 1 Specification for iron castings with spheroidal or nodular graphite for pressure containing parts for use at elevated temperatures
516 5819 1970 Recommended short circuit ratings of high voltage PVC cables
517 5821 1986 2nd Specification for hot water hose of rubber
518 5856 1991 1st Corrosion and heat resisting chromium nickel and chromium steel solid welding rods and bare electrodes - specification
519 5898 1970 Specification for copper and copper alloy bare solid welding rods and electrodes
520 5957 1970 Dimensions for Screw Threads for Thread Forming Tapping Screws
521 5961 1970 Specification for cast iron gratings for drainage purposes
522 5986 1992 1st 4 Hot rolled steel plates, sheets, strips and flats for flanging and forming operation - specification
523 5988 1970 Specification for spring dowel sleeves (light and heavy patterns) for use in foundries
524 6094 1981 1st Specification for hexagon socket set screws
525 6101 1982 1st Specification for slotted pan head screws
526 6113 1970 Specification for aluminium fasteners for building purposes
527 6132 2003 1st Forged shackles for general lifting purposes -dee shackles and bow shackles
528 6157 1981 1st Valve inspection and test
529 6166 1971 Specification for thin taper keys and keyways
530 6167 1971 Specification for Thin Parallel Keys and Keyways
531 6206 1985 1st 1 Guide for selection, installation and maintenance of air compressor plants with operating pressures upto 10 bars
532 6210 1979 1st Method of test for stress relaxation of gasket material
533 6215 1982 1st Specification for short link chain, grade T (8), non-calibrated for lifting purposes
534 6216 1982 1st Specification for short link chain, grade T (8), calibrated for pulley blocks and other lifting appliances
535 6217 1982 1st Specification for short link chain, grade S (6), non-calibrated for lifting purposes
536 6293 1981 1st Nomenclature of the Assembly Tools for Nuts and Screws
537 6296 1983 1st Specification for short link chain grade S(6) calibrated for pulley blocks and other lifting appliances
538 6335 1971 Specification for Knurled Thumb Nuts (Fixtures)
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
539 6336 1971 Specification for Screws for Thrust Pads (Fixtures)
540 6338 1971 Specification for Clamping Screws (Fixtures)
541 6382 1984 1st Code of practice for design and installation of fixed carbon dioxide fire extinguishing system
542 6392 1971 1 Specification for steel pipe flanges
543 6401 1971 Specification for Dowel Pins for use in Foundries
544 6511 1972 Range of preferred safe working loads for cranes, lifting appliances and related excavator equipment
545 6521 1 1972 Code of practice for design of tower cranes Part-1: static and rail mounted
546 6533 1 1989 1st 1 Design and construction of steel chimney-code of practice Part-1: mechanical aspect
547 6533 2 1989 1st Structural aspect
548 6547 1972 Specification for electric chain hoists
549 6594 1977 1st 1 Technical supply conditions for steel wire ropes and strands
550 6603 1972 4 Specification for stainless steel bars and flats
551 6610 1972 Specification for heavy washers for steel structures
552 6619 1972 Safety code for semiconductor rectifier equipment
553 6623 1985 1st Specification for High Strength Structural Nuts
554 6631 1972 1 Specification for steel pipes for hydraulic purposes
555 6639 1972 Specification for Hexagon Bolts for Steel Structures
556 6647 1972 1 Specification for drill pipes for use in oil or natural gas wells
557 6649 1985 1st Specification for Hardened and Tempered Washers for High Strength Structural Bolts and Nuts
558 6665 1972 Code of practice for industrial lighting
559 6688 1981 1st Specification for taper pins
560 6689 1972 Specification for Hardened Cylindrical Pins
561 6730 1972 Specification for felt nails
562 6731 1977 1st Specification for locknuts, narrow series and lockwashers with straight inner tab for rolling bearings
563 6732 1972 Specification for double point nails
564 6733 1972 Specification for Wall and Roofing Nails
565 6734 1972 Specification for cut lath and lath nails
566 6735 1994 1st Fasteners-spring lock washers for screws with cylindrical heads-specification
567 6736 1972 Specification for Slotted Raised Countersunk Head Wood Screws
568 6738 1972 Specification for Panel Pins and Lost Head Nails
569 6739 1972 Specification for Slotted Round Head Wood Screws
570 6755 1980 1st Specification for double coil helical spring washers
571 6760 1972 Specification for Slotted Countersunk Head Wood Screws
572 6761 1994 1st Fasteners-countersunk head screws with hexagon socket-specification
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
573 6821 1973 Methods for Sampling Non-Threaded Fasteners
574 6832 1985 1st Specification for fixing screws and fixing washers for buckets for bucket elevators
575 6834 1 1973 Specification for conveyor chains, chain-wheels and attachments Part-1: chains
576 6834 2 1976 Chain wheels
577 6834 3 1976 Attachments
578 6838 1973 Dimensions for O rings and grooves for vacuum flanges
579 6862 1981 1st Specification for clevis pins
580 6863 1973 Specification for clevis pins with head
581 6911 1992 1st Stainless steel plate, sheet and sttrip-specification
582 6912 1985 1st Specification for copper and copper alloys forging stock and forgings (superseding IS 3488:1985)
583 6916 1973 Code of practice for fabrication welding of steel castings
584 6967 1973 Specification for steels for electrically welded round link chains
585 7002 1991 1st Prevailing torque type hexagon nuts (with non-metallic insert), style 1 property classes 5, 8 and 10
586 7093 1973 Specification for straight through joint boxes and lead sleeves for paper insulated lead sheathed cables upto and including 11 KV
587 7169 1974 Specification for Slotted Raised Countersunk (Oval) Head Tapping Screws
588 7170 1974 Specification for Slotted Raised Countersunk (Flat) Head Tapping Screws
589 7173 1974 Specification for Slotted Pan Head Tapping Screws
590 7178 1982 1st Technical Supply Conditions for Tapping screws
591 7199 1974 Specification for blast furnace stove refractories
592 7204 1 1974 Specification for stabilized power supplies, DC output Part-1: terms and definitions
593 7204 2 1980 Rating and performance
594 7204 3 1980 Radio-frequency interference test
595 7204 4 1980 Tests other than radio-frequency interference
596 7226 1974 Specification for cold-rolled medium, high carbon and low alloy steel strip for general engineering purposes
597 7318 1 1974 Approval tests for welders when welding procedure approval is not required Part-1: fusion welding of steel (superseding IS 1181:1967)
598 7343 1986 1st Code of practice for ultrasonic testing of ferrous welded pipes and tubular products
599 7368 1974 Specification for Grooved Taper Pins
600 7383 1974 Specification for Grooved Knuckle Pins
601 7384 1974 Specification for Grooved Straight Pins with Guide End
616 7666 1988 1st Ultrasonic examination of ferritic castings of carbon and low alloy steel-recommended procedure
617 7714 1975 Method of sealability test for gasket materials
618 7719 1975 1 Specification for metallic spiral wound gaskets
619 7743 1975 Recommended practice for magnetic particle testing and inspection of steel forgings
620 7744 1975 Dimensions for drip-feed lubricators
621 7745 1975 Dimensions for lubrication holes, grooves and bore reliefs
622 7790 1991 1st Domed cap nuts - specification
623 7795 1975 Specification for hexagon nuts with collar
624 7800 1975 Dimensions for Screw Threads and Ends for Thread Cutting Tapping Screws
625 7806 1993 2nd Martensitic steel and austenitic high alloy steel castings for high temperature corrosion services- specification
626 7811 1985 1st Specification for phosphor bronze rods and bars
627 7814 1985 1st Specification for phosphor bronze sheet and strip
628 7816 1975 Guide for testing insulation resistance of rotating machines
629 7906 1 1997 1st Helical compression springs Part-1: design and calculations for springs made from cirular section wire and bar
630 7906 2 1975 Specification for cold coiled springs made from circular section wire and bar
631 7906 3 1975 Data sheet for specifications for springs made from circular section wire and bar
632 7906 4 1987 Selection of standard cold coiled springs made from circular section wire and bar
633 7906 5 1989 Hot coiled springs made from circular section bars specification
634 7906 6 1978 Design and calculations for springs made from rectangular section bar steel
635 7906 7 1989 Quality requirements for cylindrical coil compression springs used
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
mainly as vehicle suspension springs
636 7907 1 1976 Helical extension springs Part-1: design and calculation for springs made from circular section wire and bar
637 7907 2 1976 Specification for cold coiled springs made from circular section wire and bar
638 7907 3 1975 Data sheet for specifications for springs made from circular section wire and bar
639 7907 4 1987 Selection of standard cold coiled springs made from circular section wire and bar
640 8000 1 1985 1st Geometrical tolerances on technical drawings Part-1: tolerancing of form, orientation, location and run-out and appropriate geometrical definitions
641 8000 2 1976 Geometrical Tolerancing on Technical Drawings, Maximum Material Principle
642 8000 3 1985 1st Geometrical Tolerancing on Technical Drawings, Dimensioning and Tolerancing of Profiles
643 8000 4 1985 Geometrical Tolerancing on Technical Drawings, Practical Examples of Indications on Drawings
644 8033 1976 Specification for Washers with Square Hole for Wood Fastening
645 8034 1989 1st 3 Specification for submersible pumpsets
646 8068 1976 Specification for tab washers
647 8070 1976 Specification for Slotted Capstan Screws (Tommy Bolt)
648 8084 1976 2 Specification for interconnecting bus-bars for AC voltage above 1 Kv upto and including 36 Kv
649 8130 1984 1st Specification for conductors for insulated electric cables and flexible cords
650 8141 1976 Tolerances for screw threads used in aeronautics
651 8148 1976 1 Specification for packaged air conditioners
652 8183 1993 1st 1 Bonded mineral wool - specification
653 8188 1999 1st Treatment of water for cooling towers - code of practice
654 8208 1976 Sizes for cylinder bores and piston rod diameters for fluid power systems
655 8223 1976 Dimensions and output ratings for foot-mounted rotating electrical machines with frame numbers 355 to 1000
656 8262 1 1976 Specification for quick release couplings for vacuum pipelines Part-1: screwed type
657 8262 2 1976 Clamped type
658 8266 1976 Specification for expansion shell type roof bolts
659 8324 1988 1st Code of practice for safe use and maintenance on non-calibrated round steel link lifting chains and chain slings
660 8351 1977 Specification for spiral pins (heavy duty type)
661 8352 1977 Specification for flat countersunk square neck bolts
662 8353 1977 Specification for flat countersunk nib bolts
663 8379 1977 Specification for spiral pins (medium duty type)
664 8412 1977 Specification for slotted countersunk head bolts for steel structures
665 8468 1977 1 Specification for on-load tap-changers
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
666 8474 1977 Procedure for Inspection and Testing of Aluminium and Aluminium
Alloy Wires (For Rivets) for Aircraft Purposes 667 8500 1991 1st Structural steel - microalloyed (medium and high strength qualities)
- specification 668 8504 2 1983 Guide for determination of thermal endurance properties of
electrical insulating materials Part-2: list of materials and available tests
669 8513 1977 Specification for Aluminium Alloy Wire for Cold Forged Rivets for Aircraft Purposes (Alloy 55000)
670 8514 1977 Specification for Aluminium Alloy Wire for Cold Forged Rivets for Aircraft Purposes (Alloy 24530)
671 8515 1977 Specification for Aluminium Wire for Cold Forged Rivets for Aircraft Purposes (Alloy 19500)
672 8535 1977 Terminology for Features of Fasteners
673 8536 1977 Dimensioning of Fasteners
674 8563 1977 Specification for Half Round Mild Steel Wire for the Manufacture of Split Pins
675 8573 1977 Specification for digital electronic DC voltmeters and DC electronic analogue to digital converters
676 8593 1 1977 Recommendations for centralised lubrication as applied to plant and machinery Part-1: oil lubrication
677 8593 2 1988 Grease lubrication
678 8593 3 1984 Aerosol lubrication
679 8597 1977 Specification for flat belt conveyors
680 8598 1987 1st Specification for idlers and idler sets for belt conveyors
681 8599 1977 Recommendations for selection of apron conveyors
682 8603 1 1977 Dimensions for procleain transformer bushings for use in heavily polluted atmospheres Part-1: 12 KV and 17.5 KV bushings
683 8603 2 1977 24 KV bushings
684 8647 1977 Design criteria for pneumatic conveying systems
685 8660 1978 Purchaser's data sheet for vibrators for use with bin and hopper
686 8666 1977 Specification for copper and copper alloy covered electrodes for manual metal arc welding
687 8667 1977 Purchaser's data sheet for cooling towers for process industry
688 8690 1977 Application guide for measuring devices for high voltage testing
689 8721 1978 Specification for fish bolts (cup oval neck bolts) for collieries
690 8722 1978 Specification for fish bolts with square head for collieries
691 8723 1978 Dimensions for vibrating conveyors and feeders with rectangular or trapezodial trough
692 8780 1978 1 Code of practice for non-destructive testing of steel castings
693 8784 1987 2nd Specification for thermocouple compensating cables
694 8791 1978 Code of practice for ultrasonic flaw detection of ferritic steel forgings
695 8822 1978 Specification for slotted mushroom head roofing bolts
696 8856 1978 Specification for Hexagon Weld Nuts
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
697 8869 1978 Specification for washers for corrugated sheet roofing
698 8910 1978 General technical delivery requirements for steel and steel products
699 8911 1988 Specification for slotted raised countersunk head screws
700 8912 1978 Methods of measurement of suppression characteristics of electromagnetic interference filters
701 8936 1978 Specification for Aluminium Alloy Wire for Cold Forged Rivets for Aircraft Purposes (Alloy 24350)
702 8937 1978 Specification for Aluminium Alloy Wire for Cold Forged Rivets for Aircraft Purposes (Alloy 22500)
703 8938 1978 Specification for Aluminium Alloy Wire for Cold Forged Rivets for Aircraft Purposes (Alloy 24345)
704 8953 1978 Specification for 62 percent alumina bricks and blocks for blast furnace
705 8976 1978 Guide for preparation and arrangement of sets of drawings and part lists
706 9086 1979 Specification for universal head aluminium alloy rivets for aircraft
707 9087 1979 Specification for 1000 countersunk aluminium alloy rivets for aircraft
708 9088 1979 Specification for universal head nickel alloy rivets for aircraft
709 9089 1996 1st Aircraft-aluminium and wrought aluminium alloy rivets - general requirements
710 9093 1979 Specification for 1000 countersunk nickel alloy rivets for aircraft
711 9137 1978 2 Code for acceptance tests for centrifugal, mixed flow and axial pumps - class C
712 9178 1 1979 Criteria for design of steel bins for storage of bulk materials, Part 1 : General requirements and assessment of loads
713 9178 2 1979 Criteria for design of steel bins for storage of bulk materials, Part 1 : Design Criteria
714 9178 3 1980 2 Criteria for design of steel bins for storage of bulk materials, Part 1 : Bins designed for mass flow and funnel flow
715 9193 1988 1st Specification for bearing pullers
716 9201 1987 1st Specification for pumps for handling slurry
717 9229 1979 Specification for inductors for electromagnetic interference suppression
718 9269 1990 1st Evaluation of pressure drop versus flow characteristics of hydraulic filter elements and filters - method of test
719 9281 1 1979 Specification for electronic weighing systems Part-1: terms and definitions
720 9281 2 1979 Methods of measurements
721 9281 4 1983 Code of practice for use and installation
722 9334 1986 1st Specification for electric motor operated actuators
723 9338 1984 1st Specification for cast iron screw-down stop valves and stop and check valves for water works purposes
724 9347 1979 Specification for charts for recording instruments
725 9349 1986 1st Recommendations for structural design of medium and high head slide gates
726 9387 1 1979 Specification for taper male stud elbow body for oil hydraulic couplings Part-1: made from forgings
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
727 9387 2 1979 Made from bar stock
728 9388 1 1979 Specification for equal elbow body for oil hydraulic couplings Part-1: made form forgings
729 9388 2 1979 Made from bar stock
730 9391 1980 Specification for straight coupling assemblies for oil hydraulic systems
731 9411 1980 Specification for elbow coupling assemblies for oil hydraulic systems
732 9428 1993 1st Preformed calcium silicate insulation (for temperature up to 9500C)- specification
733 9431 1979 Specification for indoor post insulators of organic material for systems with nominal voltages greater than 1000V up to and including 300 KV
734 9446 1980 Graphical symbols for pipelines and instrumentation diagrams
735 9507 1979 Specification for general purpose electric power driven winches for lifting and hauling
736 9515 1980 Specification for link V-belts
737 9516 1980 1 Specification for heat resisting steels
738 9519 1980 Dimensions for width across flats for hexagon head bolts and nuts
739 9520 1980 2 Nominal sizes for valves
740 9549 1980 Dimensions for split pin holes, wire holes and head slots for bolts
741 9565 1995 2nd Acceptance standards for ultrasonic inspection of steel castings - specification
742 9595 1996 1st Metal arc welding of carbon and carbon manganese steels - recommendations
743 9645 1980 Specification for threaded plugs
744 9705 1 1980 Specification for quick release coupling for vacuum pipe lines Part-1: screwed couplings type B
745 9805 1981 Specification for high conductivity copper castings
760 10047 1981 Methods of testing refractory ramming masses
761 10055 1982 Specification for jute needleloom felts
762 10118 1 1982 Code of practice for selection, installation and maintenance of switchgear and control gear Part-1: general
763 10118 2 1982 Selection
764 10118 3 1982 Installation
765 10118 4 1982 Maintenance
766 10186 1982 Recommendations for manual tungsten inert gas arc welding of copper and copper alloys
767 10221 1982 Code of practice for coating and wrapping of underground mild steel pipelines.
768 10238 1982 Specification for Step Bolt for Steel Structures
769 10248 1982 Specification for cylindrical pins with internal threads
770 10333 1982 Specification for epoxy resin systems for cast resin insulated power and control cable joints and terminations up to and including 11 KV
771 10447 1983 Guidelines for utilization and disposal of solid wastes from integrated steel plants
772 10522 1983 Specification for antiwear hydraulic oil
773 10531 1983 Code of practice for selection and use of fire resistant hydraulic fluids
774 10561 1983 Application guide for power transformers
775 10569 1983 Specification for aluminium bronze rods and bars
776 10585 1983 1 Method of test for cylinders for oil hydraulic systems
777 10596 1 1983 Code of practice for selection, installation, operation and maintenance of pumps for industrial applications Part-1: selection
778 10596 2 1983 Installation
779 10596 3 1983 Operation
780 10596 4 1983 Maintenance
781 10605 1989 Steel globe valves (flanged and butt welded ends) for petroleum, petrochemical and allied industries
782 10660 1983 Specification for rubber hydraulic hose with textile reinforcement
783 10711 1983 Sizes of drawing sheets (=ISO 5457:1980)
784 10712 1983 Presentation of item references on technical drawings (=ISO 6433:1981)
785 10719 1983 Method of indicating surface texture on technical drawings (=ISO 1302:1978)
786 10720 1983 Technical drawings for structural metal work (=ISO 5261:1981)
787 10721 1983 Datum and datum systems for geometrical tolerances on technical drawings (=ISO 5459:1981)
788 10724 1990 1st Acceptance standards for magnetic particle inspection of steel castings - specification
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
789 10742 1983 Specification for cast gun metal rods and bars
790 10748 1995 1st 2 Hot-rolled steel strip for welded tubes and pipes-specification
791 10774 1983 Specification for corrosion resistant high alloy steel and nickel base investment castings for general applications
792 10801 1984 Recommended procedure for heat treatment of welded fabrications
793 10810 1 1984 Methods of test for cables Part-1: annealing test for wires used as conductors
794 10810 2 1984 Tensile test for aluminium wires
795 10810 3 1984 Wrapping test for aluminium wires
796 10810 5 1984 Conductor resistance test
797 10810 6 1984 Thickness of thermoplastic and elastomeric insulation and sheath
798 10810 7 1984 Tensile strength and elongation at break of thermoplastic and elastomeric insulation and sheath
799 10810 8 1984 Breaking strength and elongation at break for impregnated paper insulation
800 10810 9 1984 Tear resistance for paper insulation
801 10810 10 1984 Loss of mass test
802 10810 11 1984 Thermal ageing in air
803 10810 12 1984 Shrinkage test
804 10810 13 1984 Ozone resistance test
805 10810 14 1984 Heat shock test
806 10810 16 1986 Accelerated ageing test by oxygen pressure method
807 10810 17 1986 Tear resistance for heavy duty sheath
808 10810 20 1984 Cold bend test
809 10810 21 1984 Cold impact test
810 10810 22 1984 Vicat softening point
811 10810 23 1984 Melt flow index
812 10810 24 1984 Water soluble impurities test of insulating paper
813 10810 25 1984 Conductivity of water extract test of insulating paper
814 10810 27 1984 Ash content test of insulating paper
815 10810 30 1984 Hot set test
816 10810 31 1984 Oil resistance test
817 10810 33 1984 Water absorption test (gravimetric)
818 10810 34 1984 Measurement of thickness of metallic sheath
819 10810 35 1984 Determination of tin in lead alloy for sheathing
820 10810 36 1984 Dimensions of armouring material
821 10810 37 1984 Tensile strength and elongation at break of armouring materials
822 10810 39 1984 Winding test on galvanized steel strips for armouring
823 10810 40 1984 Uniformity of zinc coating on steel armour
824 10810 41 1984 Mass of zinc coating on steel armour
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
825 10810 42 1984 Resistivity test of armour wires and strips and conductance test of
armour (wires/strips) 826 10810 44 1984 Spark test
827 10810 46 1984 Partial discharge test
828 10810 47 1984 Impulse test
829 10810 48 1984 Dielectric power factor test
830 10810 49 1984 Heating cycle test
831 10810 51 1984 Dripping test
832 10810 52 1984 Drainage test
833 10810 53 1984 Flammability test
834 10810 54 1984 Static flexibility test
835 10810 55 1986 Abrasion test
836 10810 56 1987 Accelerated ageing test by air pressure method
837 10810 57 1987 Flexing test
838 10810 59 1988 Determination of the amount of halogen acid gas evolved during combustion of polymeric materials taken from cables
839 10810 60 1988 Thermal stability of PVC insulation and sheath
840 10810 62 1993 Flame retardance test for bunched cables
841 10810 63 1993 Measurement of smoke density of electric cables under fire conditions
842 10987 1992 1st Code of practice for design, fabrication, testing and installation of under ground/above ground horizontal cylindrical steel storage tanks for petroleum products
843 10989 1984 1 Specification for cast or forged steel check valves (flanged or butt welding ends) for petroleum, petrochemicals, chemicals and allied industries
844 10990 1 1991 1st Technical drawings-simplified representation of pipelines Part-1: general rules and orthogonal representation (=ISO 6412-1:1989)
845 11003 1984 Recommendations for mounting dimensions for hydraulic fluid power-single rod cylinders 160 bar medium series bore 25 to 500 mm
846 11065 1 1984 Drawing practice for axonometric projections Part-1: isometric projection
847 11108 1984 3 Specification for portable fire extinguishers - halon 1211 type
848 11146 1999 1st Hydraulic fluid power-cylinders-bore and rod area ratios
849 11149 1984 1 Specification for rubber gaskets
850 11158 1984 Proportions and dimensions of symbols for geometrical tolerancing used in technical drawings
851 11169 1 1984 Specification for steels for cold heading/cold extrusion applications Part-1: wrought carbon and low alloy steels
852 11169 2 1989 Stainless steels
853 11171 1985 Specification for dry-type power transformers
854 11182 2 1984 Guide for the evaluation of insulation systems of electrical equipment Part-2: thermal endurance test procedures
855 11182 3/ S-1 1986 Electrical endurance test procedures Section-1: general
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
considerations and evaluation procedures based on normal distributions
856 11182 6 1986 Performance evaluation based on service experience and functional tests
857 11182 7/ S-1 1986 Multi factor functional testing Section-1: test procedures
858 11260 1 1985 Specification for stabilized power supplies, AC output Part-1: rating and performance
859 11260 2 1985 Tests
860 11277 1985 Recommendations for characteristic quantities and designation of hydraulic fluid power gas loaded accumulators with separators
861 11304 1985 Code of practice for control of air pollution in iron and steel plants
862 11323 1984 Specification for steel gate valves for use in marine pipe work system
863 11337 1985 Purchase specification for hydraulic cylinders
864 11362 1985 Head configuration and gauging of countersunk head screws (=ISO 7721:1983)
865 11388 1995 1st Recommendations for design of trash racks for intakes
866 11428 1 to 3 1985 Specification for wrought carbon steel butt-welding pipe fittings
867 11452 1985 Method of testing air-setting refractory mortars
868 11548 1986 Specification for capacitors for surge protection for use in voltage system above 650 V and upto 33 KV
869 11559 1995 1st Hydraulic fluid power - cylinders-rod end spherical eyes-mounting dimensions
870 11560 1995 1st Hydraulic fluid power - cylinders-rod end plain eyes-mounting dimensions
871 11566 1986 Specification for valve refractors
872 11592 1985 1 Code of practice for selection and design of belt conveyors
873 11630 1986 Method for ultrasonic testing of steel plates for pressure vessels and special applications
874 11656 1986 Specification for antiwear hydraulic oil, extra heavy duty type
875 11663 1986 Conventional representations of common features and materials on technical drawings
876 11664 1986 Folding of drawing prints
877 11665 1985 Technical drawings - title block (=ISO 7200:1984)
898 12032 11 1987 Architectural and topographical installation plants and diagrams (=IEC Pub 617-11:1983)
899 12032 13 1992 Analogue elements (=IEC Pub 617-13:1978)
900 12052 1987 Methods for determination of re-oxidation rate of sponge iron/direct reduced iron in contact with humid air and in direct contact with water
901 12063 1987 Classification of degrees of protection provided by enclosures of electrical equipment
902 12065 1987 Permissible limits of noise levels for rotating electrical machines
903 12075 1987 Mechanical vibration of rotating electrical machines with shaft heights 56 mm and higher measurement, evaluation and limits of vibration severity
904 12101 1987 Specification for roller type hold back device
905 12139 1987 Code for lubrication symbols
906 12188 1987 Specification for electric direct arc melting furnaces
907 12198 1987 Specification for sprockets for sugar industry
908 12306 1987 Methods of test for direct arc furnaces
909 12355 1988 Suppliers data sheet for vibrators for use with bin and hopper
910 12401 1988 Code of practice for selection of mechanical vibrating feeder
911 12457 1988 Code of practice for evaluation, repairs and acceptance limits of surface defects in steel plates and wide flats
912 12555 1988 Guide for signal conditioning devices for process control systems
913 12778 1989 Hot rolled steel parallel flange beam and column sections - dimensions
914 12779 1989 Rolling and cutting tolerances for hot rolled parallel flange beam
Indian Standards Available in Library S.No. IS No. Part
/Sec Year Rev. Amd. Title of Standard
and column sections-specification
915 12938 1990 Acceptance standards for radiographic inspection of steel castings
916 12951 1990 MICA insulation bricks for high temperature application - specification
917 12959 1990 Technical supply requirements for sprocket wheels for link chains