This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
ContentsEngine program.................................................................................................... 3Standard equipment ............................................................................................. 3Basic data ............................................................................................................. 4Technical data and cooling equipment recommendation..................................... 6
DI12 54A, order ref. 10-70................................................................................ 6DI12 56A, order ref. 10-71................................................................................ 8DI12 56A, order ref. 10-72.............................................................................. 10
This sketch is intended only as general sales information and must not be used for any installation purposes. See also “General”
Drawing No. 1 520 626
399
779
396
403
360
379
252
~ 0*
~ 610*
~ 21
0*
* The values for center of gravity applies for engines with standard equipment including coolant.Cooling equipment such as fan, fanring and protective grating are not included.
1434 - 1456 depending on fan type
13Part No. 1 588 878
Industrial & Marine Engines
Industrial diesels12-series with EMS
DHASection 5.
Equipment listLatest modification date: 031107
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
36 MAIN SUPPLY BOX-02 S Cable harness, length 2 meter 1 505 526-03 O Cable harness, length 8 meter 1 505 526-04 O Cable harness, length 12 meter 1 505 526
37 COORDINATOR-02 S With 1 505 545
41 THROTTLE CONTROL-30 S Without-31 O Accelerator position sensor + cable harness 2 meter 1 364 185-32 O Accelerator position sensor + cable harness 8 meter 1 364 185
45 FLYWHEEL-01 S For use with truck clutch Pilot hole Ø 62 mm 1 402 380 (B)-10 O SAE 14” Pilot hole Ø 80 mm 1 390 317 (B)-11 O For Clark 15/16” Pilot hole Ø 52 mm 1 521 690
46 FLYWHEEL HOUSING-01 S Measurements according to SAE1 Material: Silumin 1 403 464
49 ENGINE SUSPENSION-01 S Front mounting brackets 1 402 865-19 O Fixed suspension, low 1 402 865-21 O Fixed suspension, power pack type 1 402 865-22 O Fixed suspension, power pack type Front brackets only 1 402 865-25 O Stiff rubber suspension, low 1 402 865-26 O Stiff rubber suspension, low Front suspension only 1 402 865-27 O Stiff rubber suspension, power pack type 1 402 865-28 O Stiff rubber suspension, power pack type Front suspension only 1 402 865
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
51 AIR CLEANERRef Description Drw No.-01 S Without-25 O Light duty, with paper insert.
Filter area 10.6 m2For separate mounting 1 399 298
-45 O Medium duty, with paper insert and pre-cleaner. Filter area 16 m2
For separate mounting 1 399 298
51A SAFETY CARTRIDGE FOR AIR CLEANER-00 S Without-01 O Safety cartridge for medium duty air
cleanerOnly for 51-45 1 399 298
55 TURBO CHARGER-02 S Side mounted turbo charger, low 1 403 464-21 O Side mounted turbo charger, high 1 405 277
56 EXHAUST PIPE-00 S Without-11 O Pointing rearwards With exhaust brake, req 55-02 1 424 506-21 O 90° bend Ø 114, adjustable direction. 1 424 507
57 EXHAUST FITTINGS, shipped loose-00 O Without-40 S Flange Ø 89-102, not with 56-21 1 383 334-41 O Flange Ø 114, requires 56-21 1 383 334-42 O Flange Ø 130, requires 56-21 1 383 334-43 O Flange Ø 155, requires 56-21 1 383 334-51 O Flange and compensator Ø 114, requires 56-21 1 383 334-52 O Flange and compensator Ø 130, requires 56-21 1 383 334-53 O Flange and compensator Ø 155, requires 56-21 1 383 334-54 O Compensator for exhaust brake Requires 56-11 1 383 334
58 SILENCER, shipped loose-00 S Without-31 O Truck type with clamps Ø 115 1 331 676-32 O Truck type with flanges Ø 115 1 331 676-33 O Truck type with flanges Ø 130 1 331 676-34 O Truck type with flanges Ø 155 1 331 676-36 O Industrial type, with flanges Ø 130, straight outlet 1 379 683-37 O Industrial type, with flanges Ø 155, straight outlet 1 379 683
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
60 OIL SUMPRef Description Drw No.-05 S Deep front oil sump Oil dipstick on left or right hand side.
Drain plug on low left hand side.1 422 908
-06 O Deep front oil sump Oil dipstick on right hand side. Drain plug on low left hand side. Equipped for checking oil level with running engine.
1 422 908
-07 O Low oil sump Oil dipstick on left or right hand side. 1 422 908
60A OIL DIPSTICK-01 S On right hand side (in oil sump) 1 407 418-02 O On left hand side in engine block. Not with 60-07 1 407 418
61 OIL FILLER-01 S In valve cover 1 403 464-02 O On left hand side (in engine block) Not with 60A-02 or 60-07 1 407 419-03 O In valve cover and on left hand side
(in engine block), 1:st cylNot with 60-07 1 407 419
-03A O In valve cover and on left hand side (in engine block), 5:th cyl
Not with 60-07
62 OIL DRAINING-01 S With magnetic drain plug Under 1 403 464-10 O With hand pump Right hand side (delivered loose) 1 407 848-11 O With hand pump Left hand side (delivered loose) 1 407 848-12 O With hand pump With tap (delivered loose) 1 407 848
66 CRANKSHAFT PULLEY-00 S Standard-14 O With 2 extra grooves Ø 260 mm. For fan ratio 1:1,08 only 1 404 595
-15 O With 2 extra grooves Ø 192 mm. For fan ratio 1:1,08 only 1 404 595
-16 O With 3 extra grooves Ø 260 mm. Without fan only 1 404 595-17 O For poly-V belt Ø 260 mm. For fan ratio 1:1,08 only 1 404 595
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
72 FANRef Description Drw No.-01 S Without fan Without radiator-02 O Prepared for fan Ratio 1:1 Without radiator-03 O Prepared for fan Ratio 1:1,08 Without radiator-07 O Puller Ø 711 mm, ratio 1:1,08 1 385 758-08 O Pusher Ø 711 mm, ratio 1:1,08 1 385 757-09 O Puller Ø 787 mm, ratio 1:1,08. Not with 92A 1 385 760-10 O Pusher Ø 787 mm, ratio 1:1,08. Not with 92A 1 385 759-19 O Puller Ø 787 mm, ratio 1:1. Req alternator 1 385 760-20 O Pusher Ø 787 mm, ratio 1:1. Req alternator 1 385 759
75 RADIATOR AND FAN COVER -00 S Without-21 O 0.75 m2
Not for DC enginesWith fan cover for fan Ø 711 mm 1 407 843
-22 O 0.75 m2 Not for DC engines
With fan cover for fan Ø 711 mm, frame and front grating
1 407 843
-25 O 1.0 m2 With fan cover Not for fan Ø 711 mm
1 407 843
-26 O 1.0 m2 With fan cover, frame and front grating.Not for fan Ø 711mm
1 407 844
-35 O 1.2 m2
Not for DC enginesWith fan cover, Not for fan Ø 711 mm and Ø 787 mm
1 413 544
-36 O 1.2 m2
Not for DC enginesWith fan cover, frame and front grating.Not for fan Ø 711 mm and Ø 787 mm
1 413 545
75A LEVEL MONITOR-00 S Without-13 O Level monitor in expansion tank 1-pole, with 75- only 1 342 316
76 FAN RING-00 S Without-21 O Fan ring with sealing 1 407 485-22 O As 76-21 but with protective grating 1 407 485
80 STARTER-05 O Without-11 S 1-pole 6.7 kW 1 413 727-14 O 2-pole 6.7 kW 1 413 727
S = Standard equip., O = Optional equip. Technical descriptions of references, see “Equipment data”.
93 HYDRAULIC PUMPRef Description Drw No.-00 S Without-12 O Capacity: 16 l/min at 150 bar int., 25-30
bar cont.Without pressure reduction valve 1 404 226
-13 O Capacity: 22 l/min at 150 bar int., 25-30 bar cont.
Without pressure reduction valve 1 404 226
95 PROTECTION COVERS-01 S Standard-04 O With covers for drive belts. with 81- (alternator), Not with 72- 1 432 956-04 O With covers for drive belts. without 81- (alternator), Not with 72- 1 431 749
98B CORRISION PROTECTION-00 S Without-01 O 10 litre corrosion inhibitor. (mix water 90% with inhibitor 10%.)
98C FUEL PRE-FILTER C-00 O Without fuel pre-filter Requires a pre-filter from an external
manufacturer. If no filter is mounted, the engine warranty is not valid.
C-01 S Fuel pre-filter with water separator 1 407 701C-02 O Fuel pre-filter with water separator and
heater1 407 701
98P CONVERTER OIL COOLER-01 S Without-02 O Connection for converter 1 424 243
99 SPECIAL EQUIPMENTA-01 O Tool kitL-31 S Crankcase ventilation Open, direction downwardsL-36 O Crankcase ventilation In valve cover, for external connection 1 405 725L-38 O Crankcase ventilation Internal ventilation 1 405 359N-01 O Scania International ServiceQ-31 O With parts catalogue x1Q-32 O With parts catalogue x2Q-33 O With parts catalogue x3
The ambition with this book is to give you all the information you may need working with Scania engines. However, there can be parts of this book that could be described in another way or some information you wish to be added.
When you have suggestions for improvements, or you find faulty information, please copy this page, write down your opinions and send by telefax or mail to the adress below.
Your remarks may help us to further improve the following editions.
Thank you in advance for your co-operation
Sender:
Suggestion / Remark:
Mail to Scania CV ABIndustrial and Marine EnginesDept. IMSS-151 87 Södertälje, Sweden