SaXi-Grip Sheet-Pile-driver - RaMeCramec.fi/testi/wp-content/uploads/2013/01/RaMeC-SGV-Saxi-Grip-Vibrator-english.pdf · RaMeC SGV 60 / 80 Sheet – Pile - driver ( S= Saxi, G = Grip,

SaXi-Grip Sheet-Pile-driver One machine, but 4 different applications

Sheet Piles = 12–14 m (16 m) = weight >3 ton

Steel Pipes = Ø 90 – Ø 324 mm

= 12–14 m

= weight >3 ton

Double

Sheet Piles

= 8–10 m (12 m) Pontit = weight >3 ton

H-Beams = 12–14 m (16 m)

= weight >3 ton

RaMeC SGV 60 / 80 Sheet – Pile - driver ( S= Saxi, G = Grip, V= Vibra. For example RaMeC SGV 60/80 is a 60 ton vibrator equal to all competitor´s

almost 80 ton vibrators, which don´t have “centralized hit” vibra-housing system, see RaMeC´s model-program )

1. As a Sheet – Pile Driver 1.1 Max length of the pile = 12 – 14m ( 16m )

Due to its vibra – house “ sliding bearing ” system RaMeC can lift 3 ton heavy piles

1.2 Double Sheet – Piles Due to RaMeC´s “ centralized hit ” and sliding vibra-house the double piles are no longer a big challenge

1.3 Z – Profiles Even double Z – profiles are now possible because of the reasons in point 1.2

1.4 Plastic Sheet – Piles With the “ centralized hit” the plastic sheet piles will go inside the ground more easily

2. H – Beams If driving over 3 ton heavy H – beams or pipes, contact your local dealer

3. Steel – Pipes It takes about 10 minutes to convert your RaMeC into a max 324mm diameter Steel – Pipe Driver. If working with larger dia pipes, consult your local dealer

4. RaMeC´s innovations / benefits for the customer

4.1 The “ Centralized Hit ” ( only RaMeC has it ) Our “Centralized Hit” makes RaMeC at least 20% stronger than any other side -grip-vibra

Customer´s benefit : 1) RaMeC 60 ton vibrator is equal to almost 80 ton by any competitor 2) Saving 10.000 – 15.000 € in fuel – costs

4.2 Vibra – house´s Slide – Bearing – System

All vibrators run up – down – up ( = the amplitude ) Due to RaMeC´s genius vibra-house´s slide- bearing system ONLY 700kg + the pile needs to be lifted up or vibrated down. All competitors have 1200 – 1800kg heavy vibra – houses

Customer´s Benefit : 1) More practical vibra-force – more pile penetration with the same amount of energy 2) Saving a lot of fuel = can be 15.000 € / year 3) No Power-Pack Motor or 30 ton excavator needed; RaMeC + 25 ton, one class smaller excavator is ENOUGH 4) You can lift >1 ton heavy piles, until 3 ton

4.3 The slipping problem of pads = just history with RaMeC In RaMeC the vibra – force is now in the center of the pile – no more torque to “ tilt ” the vibrator. With the new clamping system we have doubled the clamping force

Customer´s Benefit : 1) No sliding less new pads needed less costs 2) Easier to drive sheet-piles vertically

4.4 MUCH LESS OVERHEATING of vibra – bearings

Like the very expensive piling rigs, also RaMeC has separate, 2x larger oil-tanks outside the vibra-houses

Customer´s Benefit : 1) Longer, continuous vibrating in tough soil 2) Less bearing service costs

5. RaMeC´s Control System 5.1 Proportional Control

All movements : 2x arms, slewing and tilting are proportional controlled

Customer´s Benefit : 1) Less crushed pile – locks or hazardous pile – tilting movements

5.2 Angel – Screen

The operator can see the angel of the pile from the screen or from the blinking light ( on the top of the widow ). If the pile is over 8 meters the operator can see the angel of the pile from the linking light instead of having to look down to the screen.

5.3 Without “ Auto - Steer ” RaMeC has + 20% more

penetration speed in soft or middle-hard soil Due to the “ centralized hit ”, in RaMeC – system the operator mainly / only needs to concentrate on the stick- cylinder to keep the pile straight

Customer´s Benefit : 1) At least 20% more hit pile m´s / a day 2) Simple, durable control system

Technical Data of RaMeC SGV:

1) RaMeC SGV 20/30 will be introduced during the autumn 2013. 2) If over 324mm pipe, please take contact with your dealer. 3) RaMeC always correlates to its 20% bigger competitors

(see points 4.1 and 4.2) 4) The oil-flow has to be measured always at 250 bar

pressure IF the working efficiency is important : the excavator cylinders need +10% more oil in the pressure of 250 bar NOTE: All 20 ton and 25 ton excavators on the market DON’T have the requested oil-flow. Before ordering a sheet pile driver, confirm the hydraulic power by measuring or from your dealer.

RaMeC

SGV 20/301) RaMeC

SGV 40/50 RaMeC

SGV 50/65 RaMeC

SGV 60/80 RaMeC

SGV 75/90

Weight 800-1000 kg 2000 kg 2000 kg 2000 kg 2200 kg

Vibra-force 203) 403) 503) 603) 753)

Excavator Class

8-12 ton4) 18-20 ton4) 20-25 ton4) 25 ton4) 30 ton4)

Oil-flow l/min (in 250bar)

60-804) 1204) 1504) 1804) 2204)

Max. pressure 320 320 320 320 320

Pile length (m) 8-10 12-14 (16) 12-14 (16) 12-14 (16) 12-14 (16)

Max. pipe diameter (mm)

Ø220 Ø3242) Ø3242) Ø3242) Ø3242)

Plastic piles yes yes yes yes yes

H-Beams yes yes yes yes yes

THE TRADITIONS CONTINUE : After the first Side – Grip Sheet – piler and technically most advanced “ NOX ” Tilt – Rotator NOW WE OFFER MOST ADVANCED / PRODUCTIVE PRODUCTS on the MARKET Y Raunisto Oy ( Ltd ), Hämeenlinna Finland www.ramec.fi E-mail : [email protected]

RaMeC MULTI-HAMMER = Breaker, Foundation Pile and Sheet Pile Hammer

Where even the 500 kW Sheet-Piling Vibra is failing to

finish the job (= Up or Down);

after 5 minutes change, the RaMeC Multi-Hammer can

finish any piling application economically (will be

introduced during autumn 2013).