Sand Vik

Ro

ck

drillin

g to

ols

To

p h

am

me

r pro

du

cts

www.sandvik.com

Sandvik Mining and Construction Tools ABSE-811 81 Sandviken, Sweden. Tel +46 26 26 20 00 Fax +46 26 26 23 00

HR-12281-ENG AB Sandvikens Tryckeri

Top hammer drilling tools Product catalogue

Products from Sandvik Mining and Construction Tools

Small hole drilling 3

Drifting and tunneling 17

Bench drilling 33

Long hole drilling 49

Rock reinforcement 63

Shank adapters 73

Grinding 91

Auxiliary tools 113

Product code information 119

Safety information 121

Numerical index with weight table 122

Notes 131

CopyrightSandvik Mining and Construction Tools ABSandviken

Top hammer products

Concerning bit diameters

Note that all bits are bigger on diameter than the given measurements in the catalogue.

Cross bits: Can be max 1 mm larger due to manufacturing tolerances.

Button bits: Are max 3,0 mm larger for some designs in order to make up for fast initial

wear on the diameter. The minimum diameter is 1,5 mm above given measurement.

Keep in mind that a bit always gives a bigger hole than the stated bit diameter.

This product catalogue is a presentation of the global

stock standard range of top-hammer rock tools manufactured by

Sandvik Mining and Construction Tools AB

Bit classifi cation code

H Very hard to hard rock > 2500 bar (250 MPa)M Medium hard rock 1500-2500 bar (150-250 MPa)S Soft rock < 1500 bar (150 MPa)

C Homogeneous (competent) rockF Fissured rock

V Very abrasive rock > 40% silicaA Abrasive rock 20-40% silicaN Non-abrasive rock 0-20% silica

_

_

Small hole drilling

Small hole drilling

Page

H19 (3/4) Integral drill steels ..........................................................5

H22 (7/8") Integral drill steels ........................................................6

Reaming tools ...................................................................................7

H22 Tapered tools, 12° taper .........................................................8

H22 Tapered tools, 11° taper ..........................................................9

Stone working tools .......................................................................10

R22 (7/8") Extension drilling tools ...............................................11

R23 (29/32") Extension drilling tools ...........................................12

R25 (1") Extension drilling tools ...................................................13

Sandvik Alpha. α250 bit thread ....................................................15

R28 (1 1/8") Extension drilling tools ............................................16

TOP HAMMER DRILLING TOOLS • 5

Small hole drillingH19 (3/4) Integral drill steels

A B22

A B

D

L108

19

1-1_7

Shank 22 x 108 mm (7/8"x 4 1/4")

400 1' 4" 24 15/16" 728-0424 400 1' 4" 29 1 9/64" 728-0429 800 2' 7" 28 1 7/64" 728-08281600 5' 3" 27 1 1/16" 728-1627

Shank 19 x 108 mm (3/4"x 4 1/4")

Dimensions Part No.L Dmm ft in mm in

400 1' 4" 29 19/64" 724-0429 800 2' 7" 28 1 7/64" 724-0828 1600 5' 3" 27 1 1/16" 724-1627 2400 7' 10" 26 1 1/32" 724-2426

600 2' – 27 1 1/16" 724-0627 1200 3' 11" 26 1 1/32" 724-1226

400 1' 4" 24 15/16" 724-0424 800 2' 7" 23 29/32" 724-0823

BA

L

D

A B108

1-1_6

19 19

Series

21

24

Boulder steel

6 • TOP HAMMER DRILLING TOOLS

Small hole drillingH22 (7/8") Integral drill steels

Shank 22x108 mm (7/8" x 4 1/4")


800 2' 7" 34 1 11/32" 714-0834-651600 5' 3" 33 1 19/64" 714-1633-652400 7' 10" 32 1 1/4" 714-2432-653200 10' 6" 31 1 7/32" 714-32314000 13' 1" 30 1 3/16" 714-40304800 15' 9" 29 1 9/64" 714-48295600 18' 4" 28 1 7/64" 714-5628-506400 21' – 27 1 1/16" 714-6427-507200 23' 8" 26 1 1/32" 714-7226-50

800 2' 7" 40 1 37/64" 714-0840-651600 5' 3" 39 1 17/32" 714-1639-652400 7' 10" 38 1 1/2" 714-2438-653200 10' 6" 37 1 29/64" 714-3237-654000 13' 1" 36 1 27/64" 714-4036-654800 15' 9" 35 1 3/8" 714-4835-655600 18' 4" 34 1 11/32" 714-5634-656400 21' – 33 1 19/64" 714-6433-657200 23' 8" 32 1 1/4" 714-7232-65

400 1' 4" 34 1 11/32" 714-0434-65 800 2' 7" 33 1 19/64" 714-0833-651200 3' 11" 32 1 1/4" 714-1232-651600 5' 3" 31 1 7/32" 714-16312000 6' 7" 30 1 3/16" 714-2030

600 2' – 35 1 3/8" 714-0635-651200 3' 11" 34 1 11/32" 714-1234-651800 5' 11" 33 1 19/64" 714-1833-652400 7' 10" 32 1 1/4" 714-2432-65

600 2' – 41 1 5/8" 714-0641-651200 3' 11" 40 1 37/64" 714-1240-651800 5' 11" 39 1 17/32" 714-1839-652400 7' 10" 38 1 1/2" 714-2438-65

Series

11

12

13

16

17

2000 6' 7" 33 1 19/64" 714-2033-658000 26' 3" 26 1 1/32" 714-8026-50 8800 28' 11" 25 1" 714-8825-5005 9600 31' 6" 25 1" 714-9625-5005

LA B

22 22

1-1_4

108

BA

D

Shank 22x108 mm (7/8"x 4 1/4")

800 2' 7" 29 1 9/64" 714-08291600 5' 3" 28 1 7/64" 714-1628-502400 7' 10" 27 1 1/16" 714-2427-50

L

D

A B22 22

108

1-1

5

BA

Shank 22x108 mm (7/8"x 4 1/4")

LA B

22 22

1-1_4

108

BA

D


Small hole drillingReaming tools

Pilot rodReaming bit

2-1_

114

795-1469

Knock-off tool for reaming bit

2-1_

110

D

4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45

Reaming bit, 6° taper

Buttons, mm Dimensions Part No.Front Gauge DNo Size No Size Angle mm in

800 2' 7 1/2" 26 1 1/32" 7922-6108-111200 3' 11 3/4" 26 1 1/32" 7922-6112-111600 5' 3" 26 1 1/32" 7922-6116-112000 6' 6 3/4" 26 1 1/32" 7922-6120-112500 8' 2 1/2" 26 1 1/32" 7922-6124-11

Pilot rod, Hex 22, 6° taper

L D Part No.mm ft in mm in

L22

108 2-1_

11222

D


Small hole drillingH22 Tapered tools, 12° taper

1-1_

27

Tapered rod

Cross bit

Button bit, short skirt

Button bit, long skirt

Flushinghole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo Size No Size No Size No Size Angle mm in

Cross bit

1x4 2x4 – – – 28 1 1/8" 7770-9028-421x4 2x4 – – – 30 1 3/16" 7770-9030-421x6 2x4.5 – – – 32 1 1/4" 7770-9032-42 1x6 2x4.5 – – – 35 1 3/8" 7770-9035-42

D

2-1_

466

Button bit

1x5 1x5 1x7 4x7 35° 28 1 1/8" 7795-6428-B481x5 1x5 1x7 4x7 35° 30 1 3/16" 7795-6430-B48

D

2-1_

465

Button bit

2x4 1x4 2x7 5x7 40° 32 1 1/4" 7795-5232-B482x4 1x3,5 2x7 5x8 40° 35 1 3/8" 7795-5235-B48 2x4 1x4 2x7 5x9 40° 38 1 1/2" 7795-5238-B48

D

2-1_

394

C

Button bit

2x4 1x3.5 2x7 5x7 40° 33 1 9/64" 7770-5233-B48 2x4 1x3.5 2x7 5x8 40° 35 1 3/8" 7770-5235-B48

L1081-1_21

Tapered rod, shank 22x108, HF-hardened - For surface drilling

2440 8' – 22 7/8" 7870-5124-11 3200 10' 6” 22 7/8" 7870-5132-114000 13' 1 1/2” 22 7/8" 7870-1140-114400 14' 5” 22 7/8" 7870-1144-11 4800 15' 9” 22 7/8" 7870-1148-115600 18' 4 1/2” 22 7/8" 7870-1156-116400 21' – 22 7/8" 7870-1164-117200 23' 7 1/2” 22 7/8" 7870-1172-118000 26' 3” 22 7/8" 7870-1180-11 8800 28' 10 1/2” 22 7/8" 7870-1188-11

L1081-1_21

Tapered rod, shank 22x108, carburized

610 2' – 22 7/8" 7870-6106-111220 4' – 22 7/8" 7870-6112-111830 6' – 22 7/8" 7870-6118-112000 6' 7” 22 7/8" 7870-6120-112440 8' – 22 7/8" 7870-6124-113050 10' – 22 7/8" 7870-6131-113660 12' – 22 7/8" 7870-6137-11

D

2-1_

393



Small hole drillingH22 Tapered tools, 11° taper

1-1_

28 Tapered rod

Button bit

Flushinghole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo Size No Size No Size No Size Angle mm in

Button bit

D

2-1_

464

1x6 2x4 2x7 3x8 35° 32 1 1/4" 7776-1932-B48 1x6 1x6 1x8 3x9 40° 36 1 7/16" 7776-1936-B48 1x6 1x6 2x8 3x9 40° 38 1 1/2" 7776-1938-B48 1x6 1x6 2x8 3x9 40° 40 1 37/64" 7776-1940-B48

D

2-1_

466

Button bit

1x6 1x6 2x8 4x8 40° 38 1 1/2" 7776-6438-B48

D

2-1_

465

Button bit

1x4 1x6 2x7 5x7 40° 32 1 1/4" 7776-4432-B48 1x5 1x5 2x7 5x7 35° 35 1 3/8" 7776-4435-B48 1x6 1x5 2x7 5x8 35° 38 1 1/2" 7776-4438-B48 1x6 1x5 2x8 5x9 35° 40 1 37/64" 7776-4440-B48

L1081-1_21

610 2' – 22 7/8" 7876-6106-11 800 2’ 7 1/2” 22 7/8” 7876-6108-111220 4' – 22 7/8" 7876-6112-111830 6' – 22 7/8" 7876-6118-112000 6’ 7” 22 7/8” 7876-6120-112440 8' – 22 7/8" 7876-6124-113050 10' – 22 7/8" 7876-6131-113600 11' 9 1/2” 22 7/8" 7876-6136-11

Tapered rod, shank 22x108, carburized



Small hole drillingStone working tools

9-1_

32

Plug hole integral steel

Shank rod

Cross bit


D

1089-1_31

19

L

Plug hole integral steel

150 6" 17 21/32" 721-1517 160 6 1/4" 20 25/32" 721-1620 200 7 7/8" 20 25/32" 721-2020 240 9 29/64" 20 25/32" 721-2420 280 11 1/32" 20 25/32" 721-2820 310 11 1/4" 20 25/32" 721-3120 160 6 1/4" 22 7/8" 721-1622 190 7 1/2" 22 7/8" 721-1922

L108R 25

2-1_

207

DDShank rod, Hex22 - R25

255 10 3/64" 22 7/8" 7802-6103-13 800 2' 2 1/2" 22 7/8" 7802-6108-13 1000 3' 3" 22 7/8" 7802-6110-13

D9_13

Cross bit, R25

381 1/2" 7732-1438-42 411 5/8" 7732-1441-42 451 3/4" 7732-1045-42


Small hole drillingR22 (7/8") Extension drilling tools

2-1_

395

Extension rodCoupling sleeveShank adapter

Cross bit

Shank rod

L

D

2-1_

80

Coupling sleeve, R22

140 – 5 1/2" 31 1 7/32" 7991-2031

255 – 10 3/64" 22 7/8" 7801-6103-13 1000 3' 3" 22 7/8" 7801-6110-13

3-1_

150

22108

R22L

Shank adapter/Shank rod, Hex 22 - R22

LR 22 R 22 2-

1_20

5

D

Extension rod R22 - Hex 22 - R22

800 2' 7" 22 7/8" 7851-1308-201200 3' 11" 22 7/8" 7851-1312-201600 5' 3" 22 7/8" 7851-1316-20


1 4.5 2 4.5 38 1 1/2" – 7731-1038-42

Cross bit

2-1_

77

D

Flushing hole, mm Bit Part No.Front Gauge D classi-No Size No Size mm in fi cation


Small hole drillingR23 (29/32") Extension drilling tools

2-1_

502A Shank adapter

MF-rod

Shank rod

Cross bit

Button bit

Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size No Size No Size Angle mm in fi cation

1 5.0 1 6 2x7 5x8 40° 35 1 3/8" HMCA 7737-5235-R481 6.0 1 6 2x7 5x8 35° 38 1 1/2" HMCA 7737-4438A-B481 5.0 1 6 2x8 5x9 35° 41 1 5/8" HMCA 7737-5241-R48

3 5.0 – 3x8 6x9 30° 45 1 3/4" HMCA 7737-5345-R48

Button bit

2-1_

384

D

2-1

_4

D

Cross bit, Extra Heavy Duty

1 4.5 2 4.5 – – – 33 1 5/16" – 7737-1633-11

2-1

_4

D

Cross bit, Heavy Duty

1 4.5 2 4.5 – – – 35 1 3/8" – 7737-1435-421 4.5 2 4.5 – – – 38 1 1/2" – 7737-1438-42

L

2-1_

334

22108

R23

Shank adapter / Shank rod, Hex 22 - R23

255 – 10 3/64" 22 7/8" 7807-6103-112400 8' – 22 7/8" 7807-6124-113200 10' – 22 7/8" 7807-6132-113600 11' 9 5/8” 22 7/8" 7807-6136-11

L

2-1

314

R23 R23D

MF-rod, R23 - Hex 22 - R23

Female end OD 31 mm.

2095 6' 10 1/2" 22 7/8" 7857-4821-203050 10' – 22 7/8" 7857-4831-20

L D mm ft in mm in Part No.

2-1_

316

D

Shank rod, Hex 25 - R23

255 – 10 3/64" 25 1" 7807-7103-113600 11' 9 " 25 1" 7807-7136-11

108

2-1_

188c

R23L

25 D


Small hole drillingR25 (1") Extension drilling tools

2-1_

397

Shank adapter Extension rodCoupling sleeve

Button bit

Cross bit

Shank rod

Shank adapter / rod, Hex 22 x R25

L

3-1_

149

22108

R25

255 – 10 3/64" 22 7/8" 7802-6103-13 800 2' 7" 22 7/8" 7802-6108-131000 3' 3" 22 7/8" 7802-6110-13



1x5 1x6 2x7 5x8 35° 35 1 3/8" HMCA 7732-5235-S481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7732-5238-S481x5 1x6 2x7 5x9 35° 38 1 1/2" HMCA 7732-5238-R481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7732-5241-S48

3x4.5 – 3x8 6x9 40° 45 1 3/4" MSCFAN 7732-5345F-R48

Button bit

2-1_

384

D

1)1)

2-1

_4

D


1x5 2x5 – – – 35 1 3/8" – 7732-1435-421x5 2x5 – – – 38 1 1/2" – 7732-1438-421x5 2x5 – – – 41 1 5/8" – 7732-1441-42

1)1)

1) For one-rod drilling.

Cross bit

1x5 2x5 – – – 45 1 3/4" – 7732-1045-421x5 2x5 – – – 51 2" – 7732-1051-42

2-1_

3

D

2-1_

316

D


Small hole drillingR25 (1") Extension drilling tools

Extension rod, R25 - Hex 25 - R25

915 3' – 25 1" 7852-2309-201220 4' – 25 1" 7852-2312-201525 5' – 25 1" 7852-2315-201830 6' – 25 1" 7852-2318-20 2435 8' – 25 1" 7852-2324-203050 10' – 25 1" 7852-2331-20


LR 25 R 25D

2-1_

5

2-1_

6

L

D


160 – 6 1/4" 35 1 3/8" 7992-2035


Small hole drillingSandvik Alpha. α250 bit thread

Button bit

2-1_

397b

Button bitShank rod

1x5 1x6 2x7 5x8 40° 35 1 3/8" HMCA 7764-5235-R481x5 1x6 2x7 5x9 35° 38 1 1/2" HMCA 7764-5238-R48

3x4.5 – 3x8 6x9 40° 45 1 3/4" MSCFAN 7764-5345F-R48

2-1_

384

D

2-1_

316_

1

D

108

2-1_

188b

250L

25 D

Shank rod, Hex 25 - α250

3600 11' 9 5/8 " 25 1" 7814-7136-11




2-1_

398b

Small hole drillingR28 (1 1/8") Extension drilling tools

Extension rodShank adapter Coupling sleeve

Button bit

Cross bit


1x5 1x6 2x7 5x9 35° 38 1 1/2" MSCFAN 7739-5238-R481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7739-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7739-5241-S481x5 1x6 2x8 5x10 35° 43 1 11/16" HMCA 7739-5243-S48

Button bit, CAPP 52

2-1_

384

D

1)1)1)

2-1_

4

D


1x5 2x5 – – – 38 1 1/2" – 7739-1438-421x5 2x5 – – – 41 1 5/8" – 7739-1441-42

1)1)

2-1_

16

LR 28 R 28D

Extension rod, R28 - Hex 28 - R28

150 – 5 29/32" 40 1 37/64" 7999-3640

L

D

2-1_

214


1) For one-rod drilling.

3050 10' – 28 1 1/8" 7859-2931-20


Drifting and tunneling

Drifting and tunneling

Page

R25 (1") bit thread .........................................................................19

Sandvik Alpha. α250 bit thread ..................................................21

R28 (1 1/8") bit thread ..................................................................22

Sandvik Alpha. α280 bit thread ....................................................23

R32 (1 1/4") bit thread .................................................................24

Sandvik Alpha. α330 bit thread ...................................................27

Sandvik Jumbo. R35 (1 3/8") bit thread ......................................29

Sandvik Extra. R35 (1 3/8") bit thread .........................................31

Sandvik RT300 bit types ................................................................32


2-1_

407

Drifting and tunnelingR25 (1") bit thread

RT300 button bit, type 52


1x5 1x6 2x7 5x8 35° 35 1 3/8" HMCA 7732-5235-S481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7732-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8” HMCA 7732-5241-S482-

1_38

4

D


1x5 2x5 – – – 35 1 3/8" – 7732-1435-421x5 2x5 – – – 38 1 1/2" – 7732-1438-421x5 2x5 41 1 5/8” – 7732-1441-422-

1_4

D

RT300 button bit, type 52 for bolt ERB 120/120+

1x5 1x6 2x7 5x9 30° 37 1 29/64" HMCA 7732-5237-S48

Shank adapter Drifter rodCross bit

Button bit

Reaming tools

Coupling sleeve


L

2-1_

337

R25DR32

Drifter rod, R32 - Hex 25 - R25

2475 8' 1 21/32" 25 1" 7853-6224-202630 8' 7 9/16” 25 1” 7853-6226-20 3090 10' 1 21/32" 25 1" 7853-6231-20

Flushing hole Ø 8.8 mm.

2-1_

384

D


Drifting and tunneling R25 (1") bit thread

150 – 5 29/32" 44 1 47/64" 7993-3644

L

2-1

_17

D

R32 coupling sleeve


Reaming tools for cut holes / Pilot adapter, 6° taper

– – 26 1 1/32" 7822-2526

2-1_116

D

ThreadR25

4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45

2-1_

110

D

Reaming tools for cut holes / Reaming bit, 6° taper

Dimensions Part No.Buttons, mm DFront Gauge Angle mm in


Drifting and tunnelingSandvik Alpha. α250 bit thread

2-1_

407b



1x4,5 1x6 2x7 5x7 45° 33 1 5/16" HMCA 7764-4433-S481x5 1x6 2x7 5x9 35° 35 1 3/8" HMCA 7764-4435-S481x5 1x6 2x7 5x9 30° 37 1 29/64" HMCA 7764-5237-S481x6 1x6 2x7 5x9 35° 38 1 1/2" HMCA 7764-5238-S481x6 1x6 2x8 5x9 35° 41 1 5/8” HMCA 7764-5241-S48

2-1_

384

D

Cross bit

1x5 2x5 – – – 33 1 5/16" – 7764-1633-421x5 2x5 – – – 35 1 3/8" – 7764-1435-421x5 2x5 – – – 38 1 1/2" – 7764-1438-421x5 2x5 41 1 5/8” – 7764-1441-42

2-1_

4

D

Shank adapter Drifter rod

Cross bit

Button bit

Reaming toolsCoupling sleeve


L

2-1_

337b

DR32 250

Drifter rod, R32 - Hex 25 - α250

2475 8' 1 7/16" 25 1" 7853-1724-202630 8' 7 9/16" 25 1" 7853-1726-203190 10' 5 19/32" 25 1" 7853-1731-203700 12' 1 1/2" 25 1" 7853-1737-20


150 – 5 29/32" 44 1 47/64" 7993-3644

L

2-1

_17

D

R32 coupling sleeve


– – – 26 1 1/32" 7822-2726

2-1_116

DThread α250

4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45

2-1_

110

D


Dimensions Part No.Buttons, mm DFront Gauge Angle mm in

L

2-1_

337b

DR32 250


2475 8' 1 7/16" 28 1 1/8" 7853-1824-202630 8' 7 9/16" 28 1 1/8" 7853-1826-202935 9' 7 9/16" 28 1 1/8" 7853-1829-203190 10' 5 19/32" 25 1" 7853-1831-20



R32 Coupling sleeve

150 – 5 29/64" 44 1 47/64" 7993-3644

L

2-1

_17

D

2-1_116

D

Reaming tools for cut holes / Pilot adapter 6° taper

– – – 26 1 1/32" 7822-1526Thread

R28

Reaming tools for cut holes / Reaming bit 6° taper

2-1_

110

D

Drifting and tunnelingR28 (1 1/8") bit thread



1x5 1x6 2x7 5x9 35° 38 1 1/2" MCAN 7739-5238-R481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7739-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7739-5241-S482-

1_38

4

D

Button bit

Reaming tools

Coupling sleeve Drifter rodShank adapter



L

2-1_

339

R28R32 D

3090 10' 1 21/32" 28 1 1/8" 7853-7631-203700 12' 1 1/2" 28 1 1/8" 7853-7637-20


2-1_

407b

Cross bit

Cross bit , Heavy Duty

2-1_

4

D

1x5 2x5 – – – 38 1 1/2" – 7739-1438-42

4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45



R32 Coupling sleeve

150 – 5 29/64" 44 1 47/64" 7993-3644

L

2-1

_17

D



1x5 1x6 2x7 5x9 35° 38 1 1/2" MCAN 7765-5238-R481x5 1x6 2x7 5x9 30° 38 1 1/2" HMCA 7765-5238-S481x5 1x6 2x8 5x9 35° 41 1 5/8" HMCA 7765-5241-S481x5 1x6 2x8 5x10 35° 43 1 11/16" HMCA 7765-5243-S48

2-1_

384

D

Button bit

Reaming tools

Coupling sleeve Drifter rodShank adapter



L

2-1_

339

R28R32 D

3090 10' 1 21/32" 28 1 1/8" 7853-2631-203700 12' 1 1/2" 28 1 1/8" 7853-2637-20


2-1_

407b

Cross bit

α280

2-1_116

D

Reaming tools for cut holes / Pilot adapter 6° taper

– – – 26 1 1/32" 7822-2826Thread

R28

Reaming tools for cut holes / Reaming bit 6° taper

2-1_

110

D

Cross bit , Heavy Duty

2-1_

4

D

1x5 2x5 – – – 38 1 1/2" – 7765-1438-42

4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45

α280





1x5 1x7.5 2x9 5x10 35° 43 1 11/16" HMCVA 7733-5243-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HMCVA 7733-5245-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HCV 7733-5245-S651x6 1x7.5 2x9 5x11 35° 48 1 7/8" HMCVA 7733-5248-S481x6 1x7.5 2x10 5x12 35° 51 2" HMCVA 7733-5251-S481x6 1x7.5 2x10 5x12 35° 51 2" HCV 7733-5251-S65

2-1_

386

D


3x4.5 – 3x8 6x10 25° 45 1 3/4" HMCAN 7733-5345-S483x4.5 – 3x8 6x10 30° 45 1 3/4" MSCAN 7733-5345-R483x5 – 3x9 6x10 30° 48 1 7/8" HMCAN 7733-5348-S483x6 – 3x9 6x10 35° 51 2" HMCAN 7733-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7733-5351-R48

2-1_

316

D


2x6 – 2x9 6x9 40° 43 1 11/16" MSCAN 7733-5443-R482x6 – 2x9 6x10 35° 45 1 3/4" MSCAN 7733-5445-R482x7 – 2x9 6x10 40° 48 1 7/8" MSCAN 7733-5448-R482x7 – 2x10 6x10 40° 51 2" MSCAN 7733-5451-R48

2-1_

294

D


1x5 4x6 – – – 45 1 3/4" – 7733-1345A-42

2-1_

24

D

MF-rod

Reaming tools

Shank adapter

Coupling sleeve Drifter rod

Button bit

Cross bit





3090 10' 1 21/32" 35 1 3/8" 7854-9631-203700 12' 1 1/2" 35 1 3/8" 7854-9637-204305 14' 1 31/64" 35 1 3/8" 7854-9643-204915 16' 1 1/2" 35 1 3/8" 7854-9649-20L

R32R38

2-1_

342

D



3700 12' 1 1/2" 32 1 1/4" 7854-8637-204305 14' 1 31/64" 32 1 1/4" 7854-8643-204915 16' 1 1/2" 32 1 1/4" 7854-8649-20


MF-rod, T38 - Hex 35 - R32

3700 12' 1 1/2" 35 1 3/8" 7324-6537-204305 14' 1 31/64" 35 1 3/8" 7324-6543-20

R 32LT 38

2-1_

301

D

Flushing hole Ø 9.5 mm.Female end OD 56 mm.

Drifter rod, T38 - Hex 35 - R323090 10' 1 21/32" 35 1 3/8" 7324-9631-203700 12' 1 1/2" 35 1 3/8" 7324-9637-204305 14' 1 31/64" 35 1 3/8" 7324-9643-204915 16' 1 1/2" 35 1 3/8" 7324-9649-205525 18' 1 33/64" 35 1 3/8" 7324-9655-206135 20' 1 1/2" 35 1 3/8" 7324-9661-20

2-1_

344

LR32T38 D


Coupling sleeve

L

2-1_

361

D

170 – 6 3/4" 55 2 5/32" 7994-3655191 – 7 1/2" 52 2" 7314-3652

R38T38

Drifter rod, T38 - Hex 32 - R32

3700 12' 1 1/2" 32 1 1/4" 7324-8637-204305 14' 1 31/64" 32 1 1/4" 7324-8643-20


2-1_

343

LT38 R32D

LR32R38

2-1_

342

D




2-1_

110

D

4x8 8x9 25° 64 2 1/2" 7722-4864-S454x10 8x10 30° 76 3" 7722-4876-S454x10 8x10 30° 89 3 1/2" 7722-4889-S45


2-1_

118

D

4x10 8x12 35° 89 3 1/2" 7721-4889-S454x12 8x12 35° 102 4" 7721-4802-S454x12 8x12 35° 127 5" 7721-4827-S45


– – – 26 1 1/32" 7822-3526

2-1_116

D


ThreadR32


2-1_117

D– – – 40 1 37/64" 7821-3440

ThreadR32

Reaming tools for cut holes / Reaming bit, R32

Flushing hole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo size No Size No Size No Size Angle mm in

2x6 2x6 1x13 16x13 35° 102 4" 7733-5602-S45

D

2-1_

538




1x5 1x7.5 2x9 5x10 35° 43 1 11/16" HMCVA 7766-5243-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HMCVA 7766-5245-S481x5 1x7.5 2x9 5x11 30° 45 1 3/4" HCV 7766-5245-S651x6 1x7.5 2x9 5x11 35° 48 1 7/8" HMCVA 7766-5248-S48

2-1_

386b

D

RT300 button bit, type 533x4.5 1x5 3x8 6x10 30° 45 1 3/4" MSCAN 7766-5345A-R483x4.5 1x5 3x8 6x10 25° 45 1 3/4" HMCAN 7766-5345A-S483x5 1x5 3x9 6x10 30° 48 1 7/8" MSCAN 7766-5348A-R483x5 1x5 3x9 6x10 30° 48 1 7/8" HMCAN 7766-5348A-S483x6 1x5 3x9 6x10 35° 51 2" MSCAN 7766-5351A-R483x6 1x5 3x9 6x10 35° 51 2" HMCAN 7766-5351A-S48

2-1_

316b

D


2x6 – 2x9 6x9 40° 43 1 11/16" MSCAN 7766-5443-R482x6 – 2x9 6x10 35° 45 1 3/4" MSCAN 7766-5445-R48

2-1_

294b

D

-1_409b

Reaming toolsShank adapter Coupling sleeve Drifter rod

Button bit

Drifter rod, T38 - Hex 35 - α330

2-1_

470

Lα 330T38 D

3090 10' 1 21/32" 35 1 3/8" 7324-4131-203700 12' 1 1/2" 35 1 3/8" 7324-4137-204305 14' 1 31/64" 35 1 3/8" 7324-4143-204915 16' 1 1/2" 35 1 3/8" 7324-4149-205525 18' 1 33/64" 35 1 3/8" 7324-4155-20


Cross bit

1x5 4x6 45 1 3/4" 7766-1345A-421x5 2x7.5 48 1 7/8" 7766-1448-42

2-1_

24

D



3090 10' 1 21/32" 39 1 1/2" 7324-4231-203700 12' 1 1/2" 39 1 1/2" 7324-4237-204305 14' 1 31/64" 39 1 1/2" 7324-4243-204915 16' 1 1/2" 39 1 1/2" 7324-4249-205525 18' 1 33/64" 39 1 1/2" 7324-4255-206135 20' 1 1/2" 39 1 1/2" 7324-4261-206400 21' – 39 1 1/2" 7324-4264-20

2-1_

469

LT38 D α 330

Drifter rod, T38 - Round 39 - α 330




2-1_

118

D

4x10 8x12 35° 89 3 1/2" 7721-4889-S454x12 8x12 35° 102 4" 7721-4802-S454x12 8x12 35° 127 5" 7721-4827-S45


2-1_117b

D 40 1 37/64” 7821-3040

Thread α330

Reaming tools for cut holes / α330 reaming bit

2x6 2x6 1x13 16x13 35° 102 4" 7766-5602-S45

D

2-1_

538b


Flushinghole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge D No Size No Size No Size No Size Angle mm in

T38 coupling sleeve

L

2-1_

361

D191 – 7 1/2" 52 2" 7314-3652



Drifting and tunnelingSandvik Jumbo. R35 (1 3/8") bit thread



3x5 1x5 3x9 6x10 30° 48 1 7/8" HMCAN 7738-5348A-S483x5 1x5 3x9 6x10 30° 48 1 7/8" MSCAN 7738-5348A-R483x5 – 3x9 6x10 30° 48 1 7/8" HMCAN 7738-5348-S483x5 – 3x9 6x10 30° 48 1 7/8" MSCAN 7738-5348-R483x6 – 3x9 6x10 35° 51 2" HMCAN 7738-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7738-5351-R48

2-1_

316

D


1x5 1x7.5 2x9 5x11 35° 48 1 7/8" HMCVA 7738-5248-S481x5 1x7.5 2x10 5x12 35° 51 2" HMCVA 7738-5251-S48

2-1_

511

D

2-1_

506

Reaming tools

Shank adapterCoupling sleeve

Drifter rod, Hex.

Button bitDrifter rod, Round

T38 coupling sleeve

191 – 7 1/2" 52 2" 7314-3652

4305 14' 1 31/64" 39 1 1/2" 7324-7243-204915 16' 1 1/2" 39 1 1/2" 7324-7249-205525 18' 1 33/64" 39 1 1/2" 7324-7255-202-

1_46

9

LR35T38 D

Drifter rod, T38 - Round 39 - R35



Drifter rod, T38 - Hex 35 - R35

2-1_

470

LR35T38 D

4305 14' 1 31/64" 35 1 3/8" 7324-8543-204915 16' 1 1/2" 35 1 3/8" 7324-8549-205525 18' 1 33/64" 35 1 3/8" 7324-8555-206135 20' 1 1/2" 35 1 3/8" 7324-8561-20


L

2-1_

227

D

T38 T38


1x5 2x7.5 – – – 48 1 7/8" – 7738-1448-42

2-1_

24

D


Drifting and tunnelingSandvik Jumbo. R35 (1 3/8") bit thread

2-1_117

D

ThreadR35



– – – 40 1 37/64" 7821-5440


2-1_

118

D

4x10 8x12 35° 89 3 1/2" 7721-4889-S454x12 8x12 35° 102 4" 7721-4802-S454x12 8x12 35° 127 5" 7721-4827-S45

Reaming tools for cut holes / Reaming bit, R35

Flushing hole, mm Buttons, mm Dimensions Part No.Front Gauge Front Gauge DNo size No Size No Size No Size Angle mm in

2x6 2x6 1x13 16x13 35° 102 4" 7738-5602-S45

D

2-1_

538


Drifting and tunneling Sandvik Extra. R35 (1 3/8") bit thread

Button bit, Retrac R35

Flushinghole, mm Buttons, mm Dimensions Bit Part No.Front Gauge Front Gauge D classi-No Size No Size Size Size Angle mm in fi cation

3x6 – – 3x9 3x11 25° 54 2 1/5" HMCFAN 7738-7854-S483x6 – – 3x9 3x11 30° 54 2 1/5" MSCFAN 7738-7854-R48

2-1_

508

D

2-1_

536

Drifter rod

Drifter extension rod

Shank adapterButton bitretrac

Button bit

Reaming tools

Drifter extension rod


2-1_

308b

R 35L

DT 35

Drifter rod, T35 - Round 39 - R35

4305 14’ 1 31/64 39 1 1/2” 7327-5243-204915 16' 1 1/2" 39 1 1/2" 7327-5249-205525 18' 1 33/64” 39 1 1/2" 7327-5255-206135 20' 1 1/2" 39 1 1/2" 7327-5261-20

Flushing hole Ø 14.5 mm.Female end OD 48,2 mm.

Drifter Extension rod, T35 - Round 39 - T35

2-1_

308c

T 35L

DT 35

3050 10' – 39 1 1/2" 7327-4731-20

Flushing hole Ø 14.5 mm.Female end OD 48,2 mm.


Drifting and tunneling Sandvik RT300 bits

Sandvik RT300 bits for drifting and tunneling are available in three basic designs

Type 52

Designed for hard and abrasive rock

2-1_

542

Type 53

Allround design for most types of rock

2-1_

543

Type 54

Designed for soft and less abrasive rock

2-1_

544

Non standard bitsThe products shown in this catalogue are stock standard items. Within our standard range it is possible to fi nd products suitable for

the majority of drilling conditions. Outside of this range we however undertake to manufacture non standard products to suit very

special conditions.

OptionsFollowing options are available for non standard RT300 bits for drifting and tunneling. When ordering non-standard products, a

letter that describes the option must be included in the Part No.

Example: An R32, RT300 type 53, 45mm bit with an extra hole for side fl ushing, will get the Part No.: 7733-5345A-S48.

A = One extra hole for side fl ushing

B = Two extra holes for side fl ushing

C = Grooves for front fl ushing (53 type >48mm)

D = Grooves for front fl ushing and one extra hole for side fl ushing (53 type >48mm)

E = Grooves for front fl ushing and two extra holes for side fl ushing (53 type >48mm)

F = One size smaller gauge buttons (53/54 type)

Note: If a bit has one hole for side fl ushing as standard, an A in the Part No. will give the bit one extra hole for side fl ushing, e.g. the

bit will have two holes for side fl ushing.

Options - Cemented Carbide GradesCemented carbide grade is indicated with the last letter and two digits in the Part No.

Following cemented carbide grades are available as non-standard.

S65 = Spherical DP65 buttons on 52 and 53 type

R65 = Ballistic DP65 buttons on 53 type >43mm

R55 = Ballistic DP55 buttons on 53 and 54 type >43mm

Bench drilling

Bench drilling

Page

R32 (1 1/4")....................................................................................35

T35(1 3/8") ....................................................................................37

T38 (1 1/2") ...................................................................................38

T45 (1 3/4") ....................................................................................41

T51 (2") .......................................................................................... 44

Sandvik GT60 ...............................................................................46


Bench drillingR32 (1 1/4")

2-1_

508

D

3x6 – 3x10 6x11 30° 51 2" HMCFVA 7733-7851-S453x6 – 3x10 6x11 30° 51 2" MSCFAN 7733-7851-R552x9 – 4x10 8x10 30° 64 2 1/2" HMCFVA 7733-7864-S45

Button bit, Retrac

2-1_

23 D

1x5 2x7.5 – – – 51 2" MSCFAN 7733-1451-421x5 2x7.5 – – – 64 2 1/2" MSCFAN 7733-1064-42

Cross bit

D

2-1_

600

3x6 − 3x8 6x10 40º 51 2" – 7733-8251-R453x6 − 4x8 6x10 40º 57 2 1/4" – 7733-8257-R45

Guide bit

1) For very short holes only.

D2-1_

486

2x9 – 6x10 8x11 35° 76 3" HMCAN 7733-2676-S45

Button bit

1)

2-1_

22

D

2x9 – 4x10 8x10 30° 64 2 1/2" HMCAN 7733-2664-S45

Button bit


3x6 – 3x9 6x10 35° 51 2" HMCAN 7733-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7733-5351-R483x6 – 3x10 6x11 35° 57 2 1/4" HMCAN 7733-5357C-S48

Button bit

2-1_

316_

1

D

2-1_

487

Shank adapter

Coupling sleeve

Button bit

Button bit retrac

Cross bit

MF-rod

Extension rod

Guide tube

Extension rod

Extension rod

MF-rod

Guide bit

Coupling sleeve

Coupling sleeve


Bench drillingR32 (1 1/4")

L

D

2-1_

220

Coupling sleeve R32

150 – 5 29/32" 44 1 47/64" 7993-3644

MF-rod, R32 - Round 32 - R32

3050 10' – 32 1 1/4" 7853-5131-20 3660 12' – 32 1 1/4" 7853-5137-20

2-1_

276

R 32R 32L

D

Flushing hole Ø 9.2 mm. Wrench fl at 25.4 mm.Female end OD 45 mm.

L

2-1_

29

R 32 R 32D

Extension rod, R32 - Round 32 - R32

2435 8' – 32 1 1/4" 7853-3324-30 3050 10' – 32 1 1/4" 7853-3331-30 3660 12' – 32 1 1/4" 7853-3337-30

Flushing hole Ø 11.7 mm. Wrench fl at 25.4 mm.

LD R 32R 32

2-1_

425

Guide Tube

51-64 1830 6' – 46 1 3/4" 7953-4618-2051-64 3050 10' – 46 1 3/4" 7953-4631-20

Dimensions Part No. L DBit dia, mm mm ft in mm in



Bench drillingT35(1 3/8")


Button bit, Retrac T35

3x6 – 3x9 6x11 35° 54 2 1/6" MSCFAN 7517-7854-R453x6 – 3x10 6x11 35° 57 2 1/4" MSCFAN 7517-7857-R45

2-1_

508

D

MF-rod, T35 - Round 39 - T35

3050 10' 39 1 1/2" 7327-4731-203660 12' 39 1 1/2" 7327-4737-204265 14' 39 1 1/2" 7327-4743-20

Dimensions Part No.L Dmm ft mm in

2-1_

308c

T 35L

DT 35

Female end OD 48,2 mm.

2-1_

545

Button bit retrac

MF-rodShank adapter

Flushing hole Ø 14,5 mm.


Bench drillingT38 (1 1/2")

Button bit


2x11 – 4x10 8x10 35° 64 2 1/2" MSCAN 7514-2664-R552x11 – 4x10 8x10 30° 64 2 1/2" HMCAN 7514-2664-S452x11 – 6x10 8x10 35° 70 3 3/4" HMCAN 7514-2670-S453x11 – 6x10 8x11 40° 76 3" MSCAN 7514-2676-R552x11 _ 6x10 8x10 35° 76 3" HMCAN 7514-2676-S453x10 _ 6x10 9x11 35° 89 3 1/2" HMCAN 7514-2689-S45

2-1_

322

D

2-1_

323

D

Button bit

3x7 – 3x11 6x12 30° 64 2 1/2" HMCVA 7514-3864-S453x7 – 3x11 6x12 30° 64 2 1/2" HCV 7514-3864-S65

2-1_

324

D

Button bit

3x9 – 4x11 7x12 35° 76 3" HMCVA 7514-3876-S453x9 – 4x11 7x12 35° 76 3" HMCV 7514-3876-S65

2-1_

489

D

Button bit, Drop Center

3x8 – 4x9 6x10 35° 64 2 1/2" MCAN 7514-5964-S453x8 – 4x9 6x10 40° 64 2 1/2" SCAN 7514-5964-R554x7 – 6x10 8x11 30° 76 3" MCAN 7514-5976-S454x8 – 6x10 8x11 35° 76 3" SCAN 7514-5976-R55

2-1_

490

D

Button bit, Retrac

2x11 – 4x10 8x10 30° 64 2 1/2" HMCFAN 7514-7864-S452x11 – 4x10 8x10 35° 64 2 1/2" MSCFAN 7514-7864-R55

2-1_

488

Guide tube

X-bit

Button bit Retrac

Button bit

Guide bit

Shank adapter MF-rodMF-rod

MF-rod

Coupling sleeve Extension rod Extension rod

Coupling sleeve




Button bit, Retrac

2x11 – 6x10 8x10 35° 70 2 3/4" HMCFAN 7514-7870-S452x11 – 6x10 8x11 35° 76 3" HMCFAN 7514-7876-S452x11 – 6x10 8x11 40° 76 3" MSCFAN 7514-7876-R55

2-1_

491

D

2-1_

492

D

Button bit, Retrac, Drop Center

3x8 – 4x9 6x10 35° 64 2 1/2" MCFAN 7514-7964-S453x8 – 4x9 6x10 40° 64 2 1/2" SCFAN 7514-7964-R554x7 – 6x10 8x11 30° 76 3" MCFAN 7514-7976-S454x8 – 6x10 8x11 35° 76 3" SCFAN 7514-7976-R55

2-1_

41 D

X-bit

1x7.5 2x7.5 – – – 64 2 1/2" – 7514-4064-111x7.5 2x7.5 – – – 76 3" – 7514-4076A-11

D

2-1_

601

Guide bit

3x8 – 4x9 6x11 35° 64 2 1/2" MSCFAN 7514-8264-R45

2-1_

308

T 38L

DT 38



3050 10' – 39 1 1/2" 7324-4731-703660 12' – 39 1 1/2" 7324-4737-704265 14' – 39 1 1/2" 7324-4743-70

LD

T 38T 38

2-1_

426

Guide tube

1830 6' – 56 2 13/64" 7955-5618-203660 12' – 56 2 13/64" 7955-5637-20


Bit dia. mm64-7664-76




L

2-1

47

T 38 T 38D

Flushing hole Ø 14.5 mm. Wrench fl at 32 mm.

Extension rod, T38 - Round 39 - T38

3050 10' – 39 1 1/2" 7324-4331C-303660 12' – 39 1 1/2" 7324-4337C-30


T38 coupling sleeve

191 – 7 1/2" 55 2 5/32" 7314-3355

L

D

2-1_

220


Light extension rod, T38 - Hex 32 - T38

3050 10' – 32 1 1/4" 7324-6931-20

L

2-1_

67b

T38 T 38D



2-1_

494

D


Button bit

2x12 – 6x10 8x11 35° 76 3" HMCAN 7515-2676-S452x12 – 6x10 8x11 40° 76 3" MSCAN 7515-2676-R55

2-1_

495

D

Button bit

3x10 – 6x10 9x11 40° 89 3 1/2" MSCAN 7515-2689-R553x10 – 6x10 9x11 35° 89 3 1/2" HMCAN 7515-2689-S453x10 – 6x12 9x12 35° 102 4" HMCAN 7515-2602-S45

2-1_

324

D

Button bit

3x9 – 4x11 7x12 35° 76 3" HMCVA 7515-3876-S453x9 – 4x11 7x12 35° 76 3" HCV 7515-3876-S65

D

2-1_

496

Button bit

2x13 – 6x13 8x13 35° 89 3 1/2" HMCVA 7515-3889-S452x13 – 6x13 8x13 35° 89 3 1/2" HCV 7515-3889-S65

2-1_

497

D


4x7 – 6x10 8x11 30° 76 3" MCAN 7515-5976-S454x8 – 6x10 8x11 35° 76 3" SCAN 7515-5976-R554x8 – 6x11 8x12 35° 89 3 1/2" MCAN 7515-5989-S454x8 – 6x11 8x12 40° 89 3 1/2" SCAN 7515-5989-R554x9 – 7x12 8x13 35° 102 4" MCAN 7515-5902-S454x9 – 7x12 8x13 40° 102 4" SCAN 7515-5902-R55

2-1_

491

D

Button bit, Retrac

2x12 – 6x10 8x11 35° 76 3" HMCFAN 7515-7876-S452x12 – 6x10 8x11 40° 76 3" MSCFAN 7515-7876-R55

2-1_

493b

Shank adapter

Guide bit

Button bit retrac

Button bit

MF-rod

Guide tubeCoupling sleeve

MF-rod

Extension rod



Guide bit

4x8 – 5x10 8x10 35º 70 2 3/4” MSCFAN 7515-8270-R454x8 – 6x10 8x11 35º 76 3" MSCFAN 7515-8276-R454x10 – 6x11 8x12 40º 89 3 1/2" MSCFAN 7515-8289-R45D

2-1_

602

Button bit, Retrac


3x10 – 6x10 9x11 35° 89 3 1/2" HMCFAN 7515-7889-S453x10 – 6x10 9x11 40° 89 3 1/2" MSCFAN 7515-7889-R553x10 – 6x12 9x12 35° 102 4" HMCFAN 7515-7802-S45

2-1_

498

D


4x7 – 5x10 8x10 35° 70 2 3/4” SCFAN 7515-7970-R554x7 – 6x10 8x11 30° 76 3" MCFAN 7515-7976-S454x7 – 6x10 8x11 35° 76 3" SCFAN 7515-7976-R554x8 – 6x11 8x12 35° 89 3 1/2" MCFAN 7515-7989-S454x8 – 6x11 8x12 40° 89 3 1/2" SCFAN 7515-7989-R554x9 – 7x12 8x13 40° 102 4" SCFAN 7515-7902-R554x9 – 7x12 8x13 35° 102 4" MCFAN 7515-7902-S45

2-1_

499

D

MF-rod T45 - Round 46 - T45

3050 10' – 46 1 3/4" 7325-7731-703660 12' – 46 1 3/4" 7325-7737-704265 14' – 46 1 3/4" 7325-7743-706095 20' – 46 1 3/4" 7325-7761-70

LD

2-1

_235

T 45T 45

Flushing hole Ø 17 mm. Female end OD 63 mm.

Guide tube


1830 6' – 63 2 1/2" 7956-6318-213660 12' – 63 2 1/2" 7956-6337-703660 12' – 76 3" 7956-7637-70

LD

T 45T 45

2-1_

427

Bit dia. mm76-8976-89

89-102

Female end OD 63 mm / 76 mm.




T45 coupling sleeve

210 – 8 1/8" 63 2 31/64" 7315-3663

L

D

T 45 T 45

2-1_

236

Extension rod T45 - Round 46 - T45

3050 10' – 46 1 3/4" 7325-7331C-303660 12' – 46 1 3/4" 7325-7337C-304265 14' – 46 1 3/4" 7325-7343C-306095 20' – 46 1 3/4" 7325-7361C-30

LT 45 T 45

2-1_

66

D

Flushing hole Ø 17 mm. Wrench fl at 38 mm.


2-1_

503a

Bench drillingT51 (2")

Button bit

Button bit, Retrac

Guide tube

MF- rodShank adapter

Coupling sleeve Extension rod

Coupling sleeve

Coupling sleeve

MF- rod

Extension rod

Extension rod2-

1_49

5

D

Button bit


3x12 – 6x10 9x11 35° 89 3 1/2" HMCAN 7516-2689-S453x12 – 6x12 9x12 35° 102 4" HMCAN 7516-2602-S453x12 – 9x12 9x13 35° 115 4 1/2" HMCAN 7516-2615-S453x13 – 9x13 9x14 35° 127 5" HMCAN 7516-2627-S45

2-1_

497

D


4x10 – 6x11 8x12 35° 89 3 1/2" MCAN 7516-5989-S454x10 – 7x11 8x12 40° 89 3 1/2" SCAN 7516-5989-R554x11 – 7x12 8x13 35° 102 4" MCAN 7516-5902-S454x11 – 7x12 8x13 40° 102 4" SCAN 7516-5902-R554x10 – 7x13 8x14 35° 115 4 1/2" MCAN 7516-5915-S454x10 – 7x14 8x14 35° 127 5” MCAN 7516-5927-S45

2-1_

498

D

Button bit, Retrac

3x12 – 6x10 9x11 35° 89 3 1/2" HMCFAN 7516-7889-S453x12 – 6x10 9x11 40° 89 3 1/2" MSCFAN 7516-7889-R553x12 – 6x12 9x12 35° 102 4" HMCFAN 7516-7802-S453x12 – 9x12 9x13 35° 115 4 1/2" HMCFVA 7516-7815-S45

2-1_

499

D


4x10 – 6x11 8x12 35° 89 3 1/2" MCFAN 7516-7989-S454x10 – 7x11 8x12 40° 89 3 1/2" SCFAN 7516-7989-R554x11 – 7x12 8x13 35° 102 4" MCFAN 7516-7902-S454x11 – 7x12 8x13 40° 102 4" SCFAN 7516-7902-R554x10 – 7x13 8x14 35° 115 4 1/2" MCFAN 7516-7915-S454x11 – 7x13 8x14 40° 115 4 1/2" SCFAN 7516-7915-R554x10 – 7x14 8x14 35° 127 5" MCFAN 7516-7927-S45

Button bit, Retrac, Flat face

3x14 – 9x11 9x11 35° 102 4" HMSCFVA 7516-4902-S453x15 – 10x12 9x14 35° 115 4 1/2" HMSCFVA 7516-4915-S453x14 – 10x13 9x14 35° 127 5" HMSCFVA 7516-4927-S45

2-1_

556a

D


Bench drillingT51 (2")

Coupling sleeve, T51

225 – 8 7/8" 71 2 51/64" 7316-3671225 – 8 7/8" 76 3" 7316-3676

L

D

2-1_

291a



3660 12' – 52 2" 7326-5537-704265 14' – 52 2" 7326-5543-706095 20' – 52 2" 7326-5561-70

L

2-1_

289

T 51T 51D

Extension rod, T51 - Round 52 - T51

3660 12' – 52 2" 7326-5337C-304265 14' – 52 2" 7326-5343C-306095 20' – 52 2" 7326-5361C-30

LT 51 T 51

2-1_

290

D

Flushing hole Ø 21.5 mm. Wrench fl at 45 mm.

Guide tube


1830 6' – 76 3" 7957-7618-203660 12' – 76 3" 7957-7637-703660 12' – 87 3 1/2" 7957-8737-70

ThreadBit dia. mm

89-10289-102

102-127

LD

T 51T 51

2-1_

429

Female end OD 76 / 87 mm.


2-1_

548

Shank adapter Pilot tube

Button bit

Button bit, Retrac

MF- rod



4x11 – 7x12 8x13 35° 102 4" MCAN 7620-5902-S454x11 – 7x13 8x14 35° 115 4 1/2" MCAN 7620-5915-S454x11 – 7x13 8x14 40° 115 4 1/2" SCAN 7620-5915-R554x11 – 7x14 8x14 35° 127 5" MCAN 7620-5927-S554x12 – 4x16+4x13 8x16 35° 140 5 1/2” MCAN 7620-5940-S554x12 – 4x16+4x14 8x16 35° 152 6” MCAN 7620-5952-S55

MF- rod

MF- rod


4x10 – 6x12 8x13 35° 96 3 3/4" MCFAN 7620-7996-S454x11 – 7x12 8x13 35° 102 4" MCFAN 7620-7902-S454x11 – 7x13 8x14 35° 115 4 1/2" MCFAN 7620-7915-S454x11 – 7x14 8x14 35° 127 5" MCFAN 7620-7927-S554x12 – 4x16+4x13 8x16 35° 140 5 1/2” MCFAN 7620-7940-S55

3x12 – 4x13 6x14 40° 92 3 5/8" SCFAN 7620-4792-R55


4x11 – 7x12 8x13 40° 102 4" SCFAN 7620-7902-R554x11 – 7x13 8x14 40° 115 4 1/2" SCFAN 7620-7915-R55

2-1_

500

D

D

2-1_

549b

Button bit, Flat Face, Heavy Duty

D

2-1_

496

2x14 – 6x12 8x14 35° 92 3 5/8" MCAN 7620-3892-S452x14 – 6x12 8x14 35° 96 3 3/4" MCAN 7620-3896-S453x12 – 6x12 9x14 35° 102 4" MCAN 7620-3802-S453x13 – 6x13 9x14 35° 115 4 1/2" MCAN 7620-3815-S453x13 – 6x14 9x16 35° 127 5" MCAN 7620-3827-S553x14 – 6x12 9x16 35° 140 5 1/2" MCAN 7620-3840-S55

D

2-1_

549b

Button bit, Retrac

D

2-1_

549c

2x14 – 9x12 9x12 40° 92 3 5/8" MSCFAN 7620-8792-R452x14 – 10x12 9x13 40° 102 4" MSCFAN 7620-8702-R45

Bench drillingSandvik GT60

2-1_

549d

D



Pilot Tube

1600 5' 3" 87 3 1/2" 7640-8716-704265 14' – 87 3 1/2" 7640-8743-705335 17' 6" 76 3" 7640-7653-70

Female end OD 85 mm (82 mm on 76 mm tubes)

2-1_

547

GT60 GT60

LD

MF-rod, GT60 - Round 60 (64) - GT60. For bits from 96 mm.

3660 12' - 60 2 3/8" 7610-1137-704265 14' - 60 2 3/8" 7610-1143-706095 20' - 60 2 3/8" 7610-1161-704265 14' - 64 2 1/2" 7610-1243-70

Flushing hole Ø 22.5 mm. Female end OD 85 mm.

L

2-1_

546

GT60 GT60D

MF-rod, GT60 - Round 60 - GT60. For 92-115 mm bits.

4265 14' - 60 2 3/8" 7610-1443-70


L

2-1_

546

GT60 GT60D

Button bit, Retrac, Flat Face

3x12 – 9x11 9x13 35° 102 4" HMSCFVA 7620-4902-S453x12 – 10x12 9x14 35° 115 4 1/2" HMSCFVA 7620-4915-S453x13 – 10x13 9x14 35° 127 5" HMSCFVA 7620-4927-S553x14 – 10x14 9x16 35° 140 5 1/2” HMSCFVA 7620-4940-S553x14 – 12x14 9x16 35° 152 6” HMSCFVA 7620-4952-S55

2-1_

556

D


D

2-1_

549d

3x13 – 6x13 9x16 35° 118 4 5/8" HMCFVA 7620-8118-S55

Bench drillingSandvik GT60

Long hole drilling

Long hole drilling underground

Page

R32 (1 1/4").....................................................................................................51

T35 (1 3/8") ....................................................................................................53

T38 (1 1/2") ....................................................................................................54

T45 (1 3/4") .....................................................................................................56

T51 (2") ............................................................................................................58

T45 (1 3/4") tube drilling tools ......................................................................60

ST58 (2 1/4") tube drilling tools ....................................................................61

ST68 (2 3/4") tube drilling tools.....................................................................62


Long hole drilling undergroundR32 (1 1/4")

2-1_

487

Shank adapter

Coupling sleeve

Button bit

Button bit retrac

Cross bit

MF-rod

Extension rod

Guide tube

Extension rod

Extension rod

MF-rod

Guide bit

Reaming bit


Coupling sleeve

Coupling sleeve

2-1_

508

D

3x6 – 3x10 6x11 30° 51 2" HMCFVA 7733-7851-S45

Button bit, Retrac

2-1_

23 D

1x5 2x7.5 – – – 51 2" – 7733-1451-42

Cross bit

D

2-1_

600

3x6 − 3x8 6x10 40º 51 2" MSCFAN 7733-8251-R453x6 − 4x8 6x10 40º 57 2 1/4" MSCFAN 7733-8257-R45

Guide bit

3x6 – 3x9 6x10 35° 51 2" HMCVA 7733-5351-S483x6 – 3x9 6x10 35° 51 2" MSCAN 7733-5351-R483x6 – 3x10 6x11 35° 57 2 1/4" HMCVA 7733-5357C-S48

Button bit

2-1_

316_

1

D

Pilot adapter


Long hole drilling undergroundR32 (1 1/4")

L

D

2-1_

220a

R32 coupling sleeve

150 – 5 29/32" 44 1 47/64" 7993-3644

L

2-1_

29

R 32 R 32D

Extension rod, R32 - Round 32 - R32

915 3' – 32 1 1/4" 7853-3309-20 1220 4' – 32 1 1/4" 7853-3312-20 1525 5' – 32 1 1/4" 7853-3315-20 1830 6' – 32 1 1/4" 7853-3318-20

Flushing hole Ø 11.7 mm. Wrench fl at 25.4 mm.

Dimensions Part No. L D mm ft in mm in

2-1_

127

D

4x12 8x12 35° 102 4" – 7723-4802-S45

Reaming bit

Buttons, mm Dimensions Bit Part No.Front Gauge D classi-No Size No Size Angle mm in fi cation

DT

2-1_

126

Pilot adapter for reaming of 51 mm (2") pilot holes

ThreadR32 – – – 47 1 7/8" 7823-3647

MF-rod, R32 - Round 32 - R32

915 3' – 32 1 1/4" 7853-5109-20 1220 4' – 32 1 1/4" 7853-5112-20 1525 5' – 32 1 1/4" 7853-5115-20 1830 6' – 32 1 1/4" 7853-5118-20

2-1_

276

R 32R 32L

D

Flushing hole Ø 9.2 mm. Wrench fl at 25.4 mm.Female end OD 45 mm.

Female end OD 46 mm.L

D R 32R 32

2-1_

425

Guide Tube

1830 6' – 46 1 3/4" 7953-4618-20



Long hole drilling undergroundT35 (1 3/8")


Button bit, Retrac

3x6 – 3x9 6x11 35° 54 2 1/6" MSCFAN 7517-7854-R453x6 – 3x10 6x11 35° 57 2 1/4" MSCFAN 7517-7857-R45

2-1_

508

D


1830 6' 39 1 1/2" 7327-4718-20

Dimensions Part No.L Dmm ft mm in

2-1

308c

T 35L

DT 35

Female end OD 48,2 mm.

2-1_

545

Button bit retrac

MF-rodShank adapter



2-1_

488

Guide tube


X-bit

Reaming bit

Button bit Retrac

Button bit

Guide bitPilotadapter

Shank adapterMF-rodMF-rod

MF-rod

Button bit

2x11 – 4x10 8x10 30° 64 2 1/2" HMCVA 7514-2664-S452x11 – 6x10 8x10 35° 70 3 3/4" HMCVA 7514-2670-S452x11 _ 6x10 8x10 35° 76 3" HMCVA 7514-2676-S45

2-1_

322

D

2-1_

323

D

Button bit

3x7 – 3x11 6x12 30° 64 2 1/2" HMCVA 7514-3864-S453x7 – 3x11 6x12 30° 64 2 1/2" HMCVA 7514-3864-S65

2-1_

324

D

Button bit

3x9 – 4x11 7x12 35° 76 3" HMCVA 7514-3876-S453x9 – 4x11 7x12 35° 76 3" HCV 7514-3876-S65

2-1_

489

D


3x8 – 4x9 6x10 35° 64 2 1/2" HMCVA 7514-5964-S454x7 – 6x10 8x11 30° 76 3" HMCVA 7514-5976-S45

2-1_

490

D

Button bit, Retrac

2x11 – 4x10 8x10 30° 64 2 1/2" HMCFVA 7514-7864-S45

Button bit, Retrac

2x11 – 6x10 8x10 35° 70 2 3/4" HMCFVA 7514-7870-S452x11 – 6x10 8x11 35° 76 3" HMCFVA 7514-7876-S452x11 – 6x10 8x11 40° 76 3" MSCFAN 7514-7876-R55

2-1_

491

D




2-1_

41 D

X-bit

2-1_

308

T 38L

DT 38



1220 4' – 39 1 1/2" 7324-4712C-201525 5' – 39 1 1/2" 7324-4715C-201830 6' – 39 1 1/2" 7324-4718C-20

LD

T 38T 38

2-1_

426

Guide tube

1830 6' – 56 2 13/64" 7955-5618-20



1x7.5 2x7.5 – – – 64 2 1/2" – 7514-4064-11

DT

2-1_

126

Pilot adapter for reaming of 51 mm (2") pilot holes

ThreadT38 – – 47 1 7/8" 7823-2647

2-1_

127

D

4x12 8x12 35° 102 4" – 7723-4802-S454x12 8x12 35° 127 5" – 7723-4827-S45

Reaming bit

Buttons, mm Dimensions Bit Part No.Front Gauge D classi-No Size No Size Angle mm in fi cation

2-1_

492

D


3x8 – 4x9 6x10 35° 64 2 1/2" HMCFVA 7514-7964-S453x8 – 4x9 6x10 40° 64 2 1/2" MSCFAN 7514-7964-R554x7 – 6x10 8x11 30° 76 3" HMCFVA 7514-7976-S454x8 – 6x10 8x11 35° 76 3" MSCFAN 7514-7976-R55

D

2-1_

601

Guide bit

3x8 – 4x9 6x11 35° 64 2 1/2" MSCFAN 7514-8264-R45



2-1_

493a

Shank adapter

Guide bit

Button bit retrac

Button bit

MF-rod

Guide tube

MF-rod


2-1_

324

D

Button bit

3x9 – 4x11 7x12 35° 76 3" HMCVA 7515-3876-S453x9 – 4x11 7x12 35° 76 3" HMCV 7515-3876-S65

2-1_

497

D


4x7 – 6x10 8x11 30° 76 3" HMCVA 7515-5976-S454x8 – 6x11 8x12 35° 89 3 1/2" HMCVA 7515-5989-S45

2-1_

491

D

Button bit, Retrac

2x12 – 6x10 8x11 35° 76 3" HMCFVA 7515-7876-S45


4x7 – 6x10 8x11 30° 76 3" HMCFVA 7515-7976-S454x8 – 6x11 8x12 35° 89 3 1/2" HMCFVA 7515-7989-S45

2-1_

499

D

2-1_

494

D

Button bit

2x12 – 6x10 8x11 35° 76 3" HMCVA 7515-2676-S452x13 – 6x13 8x13 35° 89 3 1/2" HMCVA 7515-3889-S452x13 – 6x13 8x13 35° 89 3 1/2" HMCV 7515-3889-S65

Guide bit

4x8 – 5x10 8x10 35º 70 2 3/4” MSCFAN 7515-8270-R454x8 – 6x10 8x11 35º 76 3" MSCFAN 7515-8276-R454x10 – 6x11 8x12 40º 89 3 1/2" MSCFAN 7515-8289-R45D

2-1_

602


MF-rod T45 - Round 46 - T45

1525 5' – 46 1 3/4" 7325-7715C-201830 6' – 46 1 3/4" 7325-7718C-20

LD

2-1

_235

T 45T 45

Flushing hole Ø 17 mm. Female end OD 63 mm.

Guide tube


1830 6' – 63 2 31/64" 7956-6318-21

LD

T 45T 45

2-1_

427

Female end OD 63 mm / 76 mm.



2-1_

503a

Long hole drilling undergroundT51 (2")

Button bit

Button bit, Retrac

Guide tube

MF- rodShank adapter

Coupling sleeve Extension rod

Coupling sleeve

Coupling sleeve

MF- rod

Extension rod

Extension rod

2-1_

495

D

Button bit



2-1_

497

D



2-1_

498

D

Button bit, Retrac

3x12 – 6x10 9x11 35° 89 3 1/2" HMCFVA 7516-7889-S453x12 – 6x12 9x12 35° 102 4" HMCFVA 7516-7802-S45

2-1_

499

D


4x10 – 6x11 8x12 35° 89 3 1/2" HMCFVA 7516-7989-S454x11 – 7x12 8x13 35° 102 4” HMCFVA 7516-7902-S45

Bit adapter coupling

Button bit, Retrac, Flat face

3x14 – 9x11 9x11 35° 102 4" MSCFVA 7516-4902-S45

2-1_

556a

D


Long hole drilling undergroundT51 (2")



1525 5’ – 52 2” 7326-5515C-201830 6' – 52 2" 7326-5518C-20

L

2-1_

289

T 51T 51D

Guide tube


1830 6' – 76 3" 7957-7618-20

LD

T 51T 51

2-1_

429

Female end OD 76 / 87 mm.


Long hole drilling undergroundT45 (1 3/4") tube drilling tools

2-1_

478

Drill tube

Button bit

Shank adapter

XDC, button bit


4x7.5 – 6x10 8x11 35° 76 3" HMCVA 7525-8476-R65

2-1_

477

D

L

2-1_

348

T 45 T 45

D

Drill tube, T45 - Round 65 - T45


1525 5' – 65 2 1/2" 7985-6315-261830 6' – 65 2 1/2" 7985-6318-26

Flushing hole Ø 18 mm.


Long hole drilling undergroundST58 (2 1/4") tube drilling tools

2-1_

479

Shank adapter Drill tube

Button bit

Reaming bit

Button bit, Guide

XDC, button bit


4x10 – 6x12 8x12 35° 89 3 1/2" HMCVA 7528-8489-R65

2-1_

477

D

Reaming bit

6X16 9X16 35° 152 6” – 7528-5652C-S65

Drill tube, ST58 - Round 76 - ST58


1525 5' – 76 3" 7378-7615-26 1830 6' – 76 3" 7378-7618-26

Flushing hole Ø 26 mm.L

2-1_

351

ST 58 ST 58D

D

2-1_

445b

Pilot diameter 76 mm.


Long hole drilling undergroundST68 (2 3/4") tube drilling tools

2-1_

484a

Shank adapter Drill tube

Button bit

Reaming bit

Button bit, Guide

XDC, button bit


4x10 – 8x12 10x12 35° 102 4" HMCVA 7529-8402-R654x10 – 8x14 10x14 35° 115 4 1/2" HMCVA 7529-8415-R65

2-1_

483

D

2-1_

451

D

Button bit, Heavy Duty2x15 – 6x14 8x14 35° 102 4" HCV 7529-6902-S65

2-1_

482

D

XDC, button bit, Guide4x10 – 8x12 10x12 35° 102 4" HMCVA 7529-7302-R654x10 – 8x14 10x14 35° 115 4 1/2" HMCVA 7529-7315-R65

Collaring bit

2-1_

357C

D

3x18 – 8x16 9x16 35° 152 6" – 7529-6652-S45

Drill tube, ST68 - Round 87 - ST68

1525 5' – 87 3 1/2" 7379-8715-261525 5' – 87 3 1/2" 7379-8715-46 1)

1830 6' – 87 3 1/2" 7379-8718-26

L

2-1_

352

ST 68 ST 68D


FLushing hole Ø 30 mm.1) Permanent back fl ow valve.

D

2-1_

445a

Reaming bit

6x16 9x16 35° 152 6” – 7529-5652C-S65

Pilot diameter 95 mm.

Rock reinforcement

Rock reinforcement

Page

Sandvik RX300 expandable rock bolts ..........................................................66

High pressure water pumps ...........................................................................69

Installation arm for RX300 bolts .................................................................70

Cleaning lance & Pull tester ............................................................................71


Rock reinforcement

Sandvik RX 300 product range

The Sandvik RX300 Expandable Rock Bolts are available in two basic qualities, simply called the ERB-line and the ERB

Plus-line. Each of them including products with three load capacity variants – 120 kN, 160 kN and 240 kN.

The main difference between the two qualities is elongation characteristics. The ERB Plus-line is made of a “softer”

steel quality and has gone through an annealing process. Due to this it can be stretched longer and more even

before breaking compared to the standard ERB-line quality. This gives the ERB Plus-line better capacity to follow rock

deformation and is for that reason better suited for rock conditions with squeezing ground or high strain concentrations

areas. The standard ERB-line quality is suitable for most other applications.

Corrosion protection and coating

The steel grades used for manufacturing of RX 300 bolts are not corrosion protected, meaning that during overseas

transportation and long storage time the bolts may be corroded. Normally this does not affect the product quality.

For overseas transportation and long storage time the bolts can be coated with an anti-corrosive agent. This will prevent

corrosion during transport and storage but not after bolt installation.

In very corrosive conditions or for increased service life, the bolts can be covered with Corrolastic Expander Paint. This

will prevent corrosion also after bolt installation.

Part No Key

7970-xxxx-xx

0 No corrosion protection

1 With anti-corrosive agent

2 With Corrolastic Expander Paint

1 ERB Standard

2 ERB Plus (+)

Length of the bolt in mm


Rock reinforcementSandvik RX300 expandable rock bolts

Face plate for ERB 120

ERB 120 / 120+

Length Weight Part No.Lmm kg

600 1,20 7970-600-xx

900 1,80 7970-900-xx

1.200 2,40 7970-1200-xx

1.500 3,00 7970-1500-xx

1.600 3,20 7970-1600-xx

1.800 3,60 7970-1800-xx

2.000 4,00 7970-2000-xx

2.100 4,20 7970-2100-xx

2.400 4,80 7970-2400-xx

2.700 5,40 7970-2700-xx

3.000 6,00 7970-3000-xx

3.300 6,60 7970-3300-xx

3.600 7,20 7970-3600-xx

4.000 8,00 7970-4000-xx

4.500 9,00 7970-4500-xx

5.000 10,00 7970-5000-xx

5.500 11,00 7970-5500-xx

6.000 12,00 7970-6000-xx

L

8-1_

107

Dimensions Weight Part No.

mm kg

Flat 150 x 150 x 6 1,08 7970-P156 Flat 150 x 150 x 8 1,44 7970-P158

Steel grade ST37

Flat

Domed 150 x 150 x 4 0,66 7970-P154D

Steel grade ST37

Domed

8-1_

107b

ERB 120 ERB 120+

Tube thickness 2 mm 2 mm

Bolt diameter 28 mm 28 mm

Original tube diameter 41 mm 41 mm

Profi le diameter 27.5 mm 27.5 mm

Bushing head diameter 30/36 mm 30/36 mm

Upper bushing diameter 28 mm 28 mm

Hole diameter 32 - 39 mm 32 - 39 mm

Optimal hole diameter 35 - 38 mm 35 - 38 mm

Breaking load 120 kN 120 kN

Minimum elongation 10 % 20 %

Typical elongation up to 30 %


8-1_

107



ERB 160 / 160+

Length Weight Part No. L mm kg

1.800 5,22 7972-1800-xx

2.100 6,09 7972-2100-xx

2.400 6,96 7972-2400-xx

2.700 7,83 7972-2700-xx

3.000 8,70 7972-3000-xx

3.300 9,57 7972-3300-xx

3.600 10,44 7972-3600-xx

4.000 11,60 7972-4000-xx

4.500 13,05 7972-4500-xx

5.000 14,50 7972-5000-xx

5.500 15,95 7972-5500-xx

6.000 17,40 7972-6000-xx

L

8-1_

106

ERB 160 ERB 160+




Profi le diameter 36 mm 36 mm








Steel grade ST37


mm kg

Flat 150 x 150 x 6 1,08 7971-P156 Flat 150 x 150 x 8 1,44 7971-P158

Domed 150 x 150 x 4 0,66 7971-P154D

Steel grade ST37

Domed

8-1_

107b

Flat



ERB 240 / 240+

Length Weight Part No.L mm kg

1.800 7,20 7971-1800-xx

2.100 8,40 7971-2100-xx

2.400 9,60 7971-2400-xx

2.700 10,80 7971-2700-xx

3.000 12,00 7971-3000-xx

3.300 13,20 7971-3300-xx

3.600 14,40 7971-3600-xx

4.000 16,00 7971-4000-xx

4.500 18,00 7971-4500-xx

5.000 20,00 7971-5000-xx

5.500 22,00 7971-5500-xx

6.000 24,00 7971-6000-xx

L

8-1_

106

8-1_

107


Steel grade ST37


mm kg

Flat 150 x 150 x 6 1,08 7971-P156 Flat 150 x 150 x 8 1,44 7971-P158

Domed 150 x 150 x 4 0,66 7971-P154D

Steel grade ST37

Domed

8-1_

107b

Flat

ERB 240 ERB 240+




Profi le diameter 36 mm 36 mm









Rock reinforcementHigh pressure water pumps

RX520E high pressure water pump for RX300 bolts

Electric high-pressure water pump for installation of RX300

expandable rock bolts

Complete pump unit 790-4200

Spare Parts and Accessories

Water fi lter 60μ 791-4101Repair Kit 3 Sealings 791-4102Repair Kit 10 Valves 791-4103High-pressure hose DN 10, 300 bar, 10 meter 791-4105

Part No.

Technical data

Maximum output ................. 21 l/min.

Maximum output ............... 1.260 l/h

Operating pressure, up to . 320 bar

Maximum working pressure 300 bar

Electricity supply ................. 32A / 400V

Rpm of the pump ............... 400 rpm

Current consumption ......... 25 A

Dimensions (LxWxH) ........ 700mm x 550mm x 620mm

Weight ............................... 76 kg

Dimension of nozzle .......... 055

Protection of splash proof . IP 55

8-1_109

RX510H - 510E high pressure water pump for RX300 bolts

Hydraulic/Electric water pump for installation of RX300 expandable

rock bolts

Complete pump unit

RX510H 790-3100

RX510E 790-4100


Water fi lter 60μ 791-4101

Repair Kit 3 Sealings 791-4102

Repair Kit 10 Valves 791-4103

High-pressure hose DN 10, 300 bar,

10 meter 791-4105

Technical data RX510H RX510E

Maximum output ................. 14 l/min 14 l/min

Maximum output ................. 840 l/h bar 840 l/h bar

Operating pressure ............ 320 bar 320 bar

Maximum working pressure 300 bar 300 bar

Normal Voltage .................. 2 • 12 V (24V) 400V

Driving effi ciency .............. 7,5 kW 7,5 kW

Rpm of the pump ............... 1400 1400

Oil pressure ....................... 170 - 200 bar

Oil quantity ........................ max 40 l/min

Amperage .......................... 16A

Dimensions in mm (L•W•H) 670•350•515 670•350•515

Approx. weight .................. 52 kg 42 kg

Nozzle dimension .............. 040 040

Recoil ................................ 66 N 66 N

Protection of splash proof . IP 55 IP 55

8-1_115


Rock reinforcementHigh pressure water pumps & Installation arm

RX500P high pressure water pump for RX300 bolts

Pneumatic high-pressure water pump for installation of RX300

expandable rock bolts

Complete pump unit 790-1100


Water fi lter 60μ 791-4101

Repair Kit 3 Sealings 791-4102

Repair Kit 10 Valves 791-4103

High-pressure hose DN 10, 300 bar,

10 meter 791-4105

Technical data

Pump type ............................ Pneumatic

Working pressure, water ... 320 bar

Max output fl ow, water ...... 9 l/min, 540 l/h

Press. amplifi cation (air-water) 64 times

Input air pressure................ 5-8 bar

Air consumption (5 bar) ..... 50-60 l/s

Input water pressure ......... 3-10 bar

Stroke volume, water ........ 50 cm3

Dimensions (LxWxH) ........ 720mm x 375mm x 360mm

Weight ............................... 34 kg

8-1_117

Part No.

Installation arm for RX300 bolts

High-pressure installation arm for RX300 expandable rock bolts.

All vital components are specially selected to withstand peak

pressures up to 500 bar.

Installation Arm with nozzle head,

ERB 120/120+ incl. 10 m high pressure hose

790-2100

Installation Arm with nozzle head,

ERB 160/160+ and 240/240+

incl. 10 m high-pressure hose 790-2200

High–pressure hose DN, 300 bar,

10 meters 791-4105

8-1_116


Cleaning lance for Sandvik high pressure water pumps

The high-pressure water pumps RX510E, RX510H and RX520E

for installation of Sandvik RX300 expandable rock bolts are also

suitable for cleaning of vehicles such as loaders and drilling

jumbos, if this cleaning lance is used.

High-pressure cleaning lance 790-2300High-pressure hose DN, 300 bar,10 meters 791-4105

8-1_118

Pull tester equipment for RX300 bolts

Hydralic pull tester for RX300 bolts, with digital pressure gauge.

Complete pull tester 790-6100

8-1_119

Rock reinforcementCleaning lance & Pull tester

Part No.

Shank adapters

Shank adapters

ROCK DRILL CATEGORIES

BE = bench drillingBO = boltingDS = dimensional stone drillingPD = production drilling underground (long hole drilling)TU = drifting and tunneling

Page

Shank rods ..................................................................................... 75

Atlas Copco ................................................................................... 76

Boart .............................................................................................. 79

Furukawa ....................................................................................... 80

Gardner-Denver, Ingersoll-Rand and Klemm ............................. 81

Montabert ..................................................................................... 82

SIG .................................................................................................. 83

Sandvik ........................................................................................... 84

Secoma and Toyo .......................................................................... 89


Shank rods

L

3-1_

15

22

108

4.5-5.0 R22 255 7801-6103-134.5-5.0 R23 255 7807-6103-11*4.5-5.0 R25 255 7802-6103-13

For hexagonal bushing 22 x 108 mm

Dimensions, mm Part No.

Flushing tube Thread L


L

3-1_

17

108

25

For hexagonal bushing 25 x 108 mm

4.5-5.0 R23 255 7807-7103-11*4.5-5.0 R25 255 7802-7103-14


L

3-1

22

159

25

For hexagonal bushing 25 x 159

8 R25 255 7802-7503-20

* No packing. Not suitable for hydraulic machines with water fl ushing.



Shank adaptersAtlas Copco

L

3-1_

29

32 25.4

57.238.1

Atlas Copco BBC 51, 52, 54 and 120

TU 10 R32 380 7803-4200-30TU 10 T38 390 7304-4200-30

3-1_

31

L

64.4

13.480

44.644.4

Atlas Copco BBE 57

BE 14 T38 537 7304-7502-60

20.5

4831.7

19 L3-

1_26

32

Atlas Copco BBC 43, 44, 45 and 100

TU 10 R32 380 7803-3100-30

Dimensions, mm Part No.Hammercategory Flushing tube Thread L

Atlas Copco COP 125, 130 and 131

TU,BE,PD 14 T38 380 7304-4500-60

L

52

32

3-1_

12

38.1 38.7

Atlas Copco COP 1032 HD

TU,BO – R32 340 7803-3588-01

L58

9

54

3-1_

120

34 45

L58

9

54

3-1_

120b

34 55 TU,BO – R38 340 7804-3575-01

Atlas Copco COP 1032

BE – T35 550 7307-3576-01

L58.5

44.9

53.9

8.8

3-1_

242

33.9


Dimensions, mm Part No.Hammercategory Flushing hole Thread L

74L 9

54

3-1_

12334 38

Atlas Copco COP 1036/1038 HB

BE – R32 500 7803-3591-01BE – T38 500 7304-3591-01

74L 9

54

3-1_

123b34 45 BE – T45 500 7305-3591-01

3-1_

124

L74 9

54

34 38

Atlas Copco COP 1038 HD/1238

TU – R32 485 7803-3590-03TU – R38 485 7804-3590-03TU – T38 485 7304-3590-03


58 9

54

3-1_

122

L

34 45

Atlas Copco COP 1032 LE

BE,DS – R32 550 7803-3576-01

74 9

54

L

3-1_

125

34 38

Atlas Copco COP 1038 HL

BE,PD – R32 575 7803-3593-01BE,PD – T38 575 7304-3593-01

74 9

54

L

3-1_

125b

34 45 BE,PD – T45 575 7305-3593-01



Atlas Copco COP 1238

74L 9

54

3-1_

12334 38 BE – R32 500 7803-3591-01

BE – T38 500 7304-3591-01TU – R38 485 7804-3590-03TU – T38 485 7304-3590-03

Dimensions, mm Part No.Hammercategoty Flushing tube Thread L

74L 9

54

3-1_

123b34 45 BE – T45 500 7305-3591-01

L9

54

3-1_

173b

38

74

34BE,PD – R32 575 7803-3593-01BE,PD – T35 575 7307-3593-01BE,PD – T38 575 7304-3593-01

3-1_

174b

34

74L

54

9

45BE,PD – T38 575 7304-3550-01BE,PD – T45 575 7305-3593-01

9

54

3-1_

204A

84.5

55

L

Atlas Copco COP 1432 Female

TU – R38 341 7804-3670-02TU – R32 341 7803-3670-02

9

54

3-1_

127A

L84.5

38 BO – R32 525 7803-3656-01BE T35 525 7307-3656-01BO – T38 525 7304-3656-01

9

54

3-1_

127

L84.5

38

Atlas Copco COP 1432, COP 1532, COP1440, COP1838 HD/ME

TU – R38 435 7804-3652-01TU – T35 435 7307-3652-01TU – T38 435 7304-3652-01 TU – R32 435 7803-3652-01


Shank adaptersAtlas Copco and Boart

54

52

125L

3-1_

205

10

Atlas Copco COP 1840 HE, COP 1850

BE,PD – T45 565 7305-3690-02BE,PD – T51 565 7306-3690-03

Atlas Copco COP 4050 EX

PD – ST68 805 7329-3716-01

136

68

70

L

3-1_

203

11.2

3-1_

171

L

52

84.5 9

54

Atlas Copco COP 1550, COP 1838 ME/ HE

BE,PD – T38 525 7304-3655-01BE,PD – T45 525 7305-3655-01BE,PD – T51 525 7306-3655-02


L

66.1

15.0

3-1_

67

64

38.1 45

Boart HD 125, HD 150, HD 160

TU – R38 495 7804-4993-01TU – T38 495 7304-4993-01

Atlas Copco COP 1550 EX, COP 1838 EX

BE – T38 730 7304-3825-02BE – T45 730 7305-3826-02

Atlas Copco COP 2150 PG

BE – T51 770 7306-3692-01

L

59.8

94

53.9

8.8

3-1_

240

53.4

8.8L124.5

51.9

3-1_

241

67.95

11.3L

112

3-1_

249

90

Atlas Copco COP 4050 MUX

PD – ST68 835 7329-3720-01


Shank adaptersFurukawa


L

71

21

3-1_

139

69

44.2 44

Furukawa PD 200R

BE 14 T38 484 7304-7581-60

64.4

13.6

3-1_

104

L79

44.3 45

Furukawa HD 260, HD 300

BE 16 T38 655 7304-7526-80BE 16 T45 655 7305-7526-80

75

35.7 44.8

3-1_

182

56.9

9.9L

Furukawa HD 609

BE – T38 620 7304-4791-01BE – T38 690 7304-4780-01BE – T45 620 7305-4791-01

L64

3-1_

43

55.5

18.2

44.5 44.3

Furukawa M 120 and PD 200

BE 14 R32 330 7803-7500-61BE 14 R38 350 7804-7500-60BE 14 T38 380 7304-7543-60BE 14 T38 446 7304-7500-60

Furukawa HD 612

BE – T45 710 7305-7414-01

89

41.7 50.8

3-1_

182b

64.9

11.75L

Furukawa HD 709

BE – T38 620 7304-7426-01

BE – T45 788 7305-7417-01

3-1_

244

L93

44.9

83

10

3-1_

243

71.8

12.3L99.5

50.8

Furukawa HD 712


Shank adaptersGardner-Denver, Ingersoll-Rand and Klemm

Gardner-Denver PR 123

TU,BE 14 R32 330 7803-7500-61TU,BE 14 R38 350 7804-7500-60TU,BE 14 T38 446 7304-7500-60TU,BE 14 T38 380 7304-7543-60

L64

3-1_

43

55.5

18.2

44.5 44.3


Ingersoll-Rand URD 475, URD 550, VL120, EVL 130, VL140 and F16

BE 14 R32 330 7803-7500-61BE 14 R38 350 7804-7500-60BE 14 T38 380 7304-7543-60BE 14 T38 446 7304-7500-60

L

64

3-1_

43

55.5

18.2

44.5 44.3

Klemm 4053

8.5

3-1_

214

56.5

74

L154

56.3 BE – R55 500 7805-6015 1)

BE – R55 500 7805-7015 2)

1) LH-Rotation 2) RH-Rotation

Ingersoll-Rand YH 65, YH 80

45

L85

3-1_

135

64.3

13.546

BE 19 T38 495 7304-7525-19BE 19 T45 500 7305-7525-19

Ingersoll-Rand YH 65 RP, YH 70 RP, YH 75 RP, YH 80 RP

BE 19 T45 700 7305-7546-19

119

L

46 45

3-1_

138b

64.8

13.5


Shank adaptersMontabert

Montabert HC40 (female)

TU, BO – R32 270 7803-4726-01

Montabert HC40

BE – R32 447 7803-4725-01 BE – R38 447 7804-4725-01

L58

3-1_

82 52.7

8.4

38.1


Montabert HC 80, HC 90, HC 105

L

52.73-1_

71

978.4

38.1TU – T38 440 7304-4720-01TU – T38 500 7304-4723-01

Montabert H 100

3-1_

31

L

64.4

13.480

44.644.4 BE 14 T38 537 7304-7502-60

3-1_

245

L58

52.6

52.6

8.4


Shank adaptersMontabert and SIG

Montabert HC 80R, HC 120R, HC 150R

BE – T51 670 7306-7528-02

9.4102

L

513-

1_10

859.7

Montabert HC 120, HC 150

BE – T45 490 7305-7520-01

9.4

59.7

3-1_

140

95L

45


SIG HBM 50, 100 and 120

L58

9

54

3-1_

120

34 45 BO – R32 340 7803-3588-01

SIG HBM 100 and 120

L58

9

54

3-1_

120b

34 55 TU, BO – R38 340 7804-3575-01

SIG HBM 50, 100 and 120

58 9

54

3-1_

122

L

34 45 BE, DS – R32 550 7803-3576-01

SIG 101

74L 9

54

3-1_

12334 38 BE – R32 500 7803-3591-01

Montabert HC 200A

BE – T51 840 7306-7530-02BE – GT60 840 7600-7530-02

11.4138

L

60

3-1_

232

73


Shank adaptersSandvik

HL 300S

BO,TU – R28 245 7809-7547-01BO,TU – R32 245 7803-7547-01

10

58.8

L39

3-1_

142

45

HL 300

BE – R32 400 7803-7549-01

10

58.8

39L

3-1_

141

32


L400, L410, L500, L510, L550

L

3-1_

58

20 20.5

4831.7 32

BO, PD, TU 10 R32 380 7803-3602-30

HLR 438L and HLR 438T

L

3-1_

55

37

57

25.7

38 38 BE, TU 12.7 R32 380 7803-4700-50BE, TU 12.7 T38 400 7304-4700-50

HLR 438LS, 438TS, HL 538, HL538L, L550S

L

3-1_

57

37

57

25.7

38 38BE, PD, TU – R32 450 7803-4700-01 BE, PD, TU – R38 450 7804-4700-01BE, PD, TU – T38 455 7304-4700-01BE – T38 545 7304-4706-01

-38 = For 38 mm front head, S=For underground drilling

HLX 3

BO,TU – R32 324 7803-7662-01

HLX 3 F

BO,TU – R32 205 7803-7663-01

58.75

7.9

3-1_

246

L53

44.85

L53

44.85

58.75

7.9

3-1_

247


HL 500-38 / 510-38

BE – R32 550 7803-7535-02BE – T35 550 7307-7535-02BE – T38 550 7304-7535-02

10

58.8

49L

3-1_

131

38

HL 500-45 / 510-45

10

58.8

45L

3-1_

168

49

BE – R32 550 7803-7557-01BE – T35 550 7307-7557-01BE – T38 550 7304-7557-01BE – T45 550 7305-7557-01


HL 500 F / 510 F

BO – R32 350 7803-7553-01

10

58.8

3-1_

183

58

45

L

HL 500 S-38 / 510 S-38 / 510 B / 510 LH

PD,TU – R32 460 7803-7531-01PD,TU – R38 460 7804-7531-01PD,TU – T38 460 7304-7531-01PD,TU – R38 500 7804-7536-01PD,TU – T38 500 7304-7536-01

10

58.8

49L

3-1_

144

38


HL 550 SUPER / 560 SUPER / 510 S-45

49

45

L

3-1_

184

10

58.8

PD,TU – T35 550 7307-7557-01TU – R38 500 7804-7554-01TU – T38 500 7304-7554-01

HLX 5 / HLX 5T

49

45

L

3-1_

212

7.9

58.7

TU – R32 500 7803-7585-01TU – T35 500 7307-7585-01TU – T38 500 7304-7585-01TU – R38 500 7804-7585-01BE – R32 575 7803-7586-01BE – T35 575 7307-7586-01BE – T38 575 7304-7586-01BE – T45 575 7305-7586-01

-38, -45 = For 38 or 45 mm front head, S=For underground drilling

HLX5 PE-45

3-1_

248

58.7

9.9L126

45

TU – R32 575 7803-7664-01TU – T38 575 7304-7664-01



HL 645

BE – T38 600 7304-7541-02BE – T45 600 7305-7541-02

L

59

68

3-1_

109

4543.8


HL 650-45 / 700-45 / 700T-45 / 710-45 / 800T-45

69

12.9

3-1_196

45

L95

BE – T38 600 7304-7576-01BE – T45 600 7305-7576-01

HL 650-52, 700-52 / PE-52 / S-52, 710-52 / S-52 / PE-52 / SPE-52, 800T-52 / PE-52

69

12.9

3-1_196B

52

L95

BE,PD – T38 600 7304-7577-02BE – T45 600 7305-7577-02BE – T51 600 7306-7577-03

HL 600-45 / 600 S-45

L75

3-1_

132

60

39.8 45

10

BE – R32 600 7803-7532-01BE – T38 600 7304-7532-01Tubes, BE – T45 600 7305-7532-01TU,PD – T38 525 7304-7537-01TU,PD – T45 525 7305-7537-01

HL 600-523-

1_17

2

L5275

10

60

39.8 BE – T45 650 7305-7551-01BE – T51 650 7306-7551-02

-45, -52 = For 45 or 52 mm front head, PE= For Power Extractor rock drill (reverse hammering), S=For underground drilling

HL 850S

BE, PD – T45 670 7305-7400-01

80

3-1_

111

69

L 14

47.4 52



HL 1000-52 / 1000 S-52

L

79

14

3-1_

133

75

52 BE – T45 670 7305-6010-01BE – T51 670 7306-6010-02PD T45 590 7305-6008-01PD T51 590 7306-6008-01

HL 1000-60

L

79

14

3-1_

133B

75

60BE – T51 670 7306-6014-02BE – GT60 670 7600-6014-02

HL 1000 S-80 Tube drilling

80L

79

14

3-1_

166

75

PD – ST58 635 7328-6009-02PD – ST68 640 7329-6009-02


HL 1000 PE-52

52

L136

3-1_

186

79

14

BE – T51 840 7306-6019-02*

* suited only for early drills with the long type of Power Extractor with 52 mm bearing diameter

-52, -60, -65, -80 = For 52, 60, 65 or 80 mm front head, PE= For Power Extractor rock drill (reverse hammering), S=For underground drilling

HL 1000-80, Shoulder drive

80L

79

14

3-1_

166

75

BE – GT60 670 7600-6031-01

BE – T51 760 7306-6025-02BE – GT60 760 7600-6025-02

HL 1000 PE-65 / HL 1500 PE-65 / HL 1560 T-65

65

L111

3-1_215

79

14




HL 1500 S-80 Tube drilling

PD – ST58 635 7328-6020-01PD – ST68 635 7329-6020-01

79

14

80

L111.5

3-1_

199

HL 1500 T-80, Shoulder drive

HL 1500-52 / 1500 T-52

BE – T51 710 7306-6021-0252

L111.5

3-1_

194

79

14

HL 1500-60 / 1500 T-60

BE – T51 760 7306-6022-02BE – GT60 760 7600-6022-0360

L111.5

3-1_

194B

79

14

BE – GT60 760 7600-6030-01

HL 1500 SPE-90 Tube drilling

PD – ST58 635 7328-6035-01PD – ST68 635 7329-6035-01

L111

3-1_215b

79

14

90

-52, -60, -65, -80, -90 = For 52, 60, 65, 80 and 90 mm front head, PE= For Power Extractor rock drill, S=For underground drilling, T= Drill with stabilizer

79

14

80

L111.5

3-1_

199


Secoma Hydrastar 200, 300 and X2

TU – R32 485 7803-3590-03TU – R38 485 7804-3590-03TU – T38 485 7304-3590-03

L

3-1_

40

74

54

9

34 38

Shank adaptersSecoma and Toyo

Secoma Hydrastar 200

TU,BO – R32 351 7803-4703-01

3-1_

130

90L

34 45

54

9


Secoma Hydrastar 350

74L 9

54

3-1_

123

34 38 BE – R32 500 7803-3591-01TU – R38 485 7804-3590-03BE – T38 500 7304-3591-01

Toyo PR 220

L64

3-1_

43

55.5

18.2

44.5 44.3 BE 14 R32 330 7803-7500-61BE 14 R38 350 7804-7500-60BE 14 T38 446 7304-7500-60

Toyo TH 501

BE 11 T38 565 7304-7583-40

3-1_

31b

L

64.2

1368

44.944.2

Grinding

Grinding

Page

Button bit grinder RG400 and RG410 ........................................93

Button bit grinder RG420P ..........................................................94

Button bit grinder RG420H .........................................................95

Button bit grinder RG420E ..........................................................96

Button bit grinder RG420P/H/E Manual ....................................97

Button bit grinder RG440 ............................................................98

Button bit grinder RG460 ............................................................99

Bit blaster RG500 .......................................................................100

Cross bit grinder RG300 ............................................................101




Integral steel grinder RG100P ....................................................105

Integral steel grinder RG100H ...................................................106

Integral steel grinder RG120E ...................................................107

Integral steel grinder RG140P/H ...............................................108

Grinding cups ..............................................................................109

Grinding wheels ..........................................................................110

Grinding accessories .................................................................. 112


Grinding Button bit grinder RG400 and RG410

RG410

Intended for grinding all kinds of button bits

Complete grinder 796-5100

Accessories optionalIn line oiler 797-5747-50Tools for O-ring replacement 797-5452Cooling/tank unit, complete 797-5488-85Grinding gauge for button up to Ø 16 mm 795-1396Grinding cups See page 109

Recommended lubricantsAir tool oil, 1 litre 797-5870-90

8-1_53b

Part No.

Technical data

Air pressure .................................. 6-8 barAir consumption ........................... 40-55 l/sSpindle speed ............................... 19000 r.p.m.Flushing air pressure ................... Max. 6 barFlushing water pressure .............. Max. 6 barWater consumption ...................... 5-6 l/minHose connections:Air, air hose ................................... 12.5 mm (1/2") ID Water, water hose ........................ 6.3 mm (1/4") IDDimensions: HxWxD mm .............. 150x450x130 Weight, without package and hose 2.9 kgWeight, with package and hose ... 3.5 kg

RG400

Technical data

Air pressure .................................. 6-8 barAir consumption ........................... 16-17 l/sSpindle speed ............................... 14000 r.p.m.Flushing air pressure ................... Max. 6 barFlushing water pressure .............. Max. 6 barWater consumption ...................... 5-6 l/minHose connections:Air, air hose ................................... 12.5 mm (1/2") ID Water, water hose ........................ 6.3 mm (1/4") IDDimensions: HxWxD mm .............. 150x450x130 Weight, without package and hose 2.9 kgWeight, with package and hose ... 3.5 kg

8-1_53b

Intended for grinding all kinds of button bits(Max. button size 10 mm)

Complete grinder 796-5116

Accessories optionalIn line oiler 797-5747-50Tools for O-ring replacement 797-5452Cooling/tank unit, complete 797-5488-85Grinding gauge for button up to Ø 16 mm 795-1396Grinding cups See page 109

Recommended lubricantsAir tool oil, 1 litre 797-5870-90


GrindingButton bit grinder RG420P

RG420P

Technical data

Air pressure ................................. Max. 13 bar/ Min. 6.5 barAir consumption ........................... 40-60 l/secWater pressure ............................ Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Rated power (motor) ..................... 1.7 kWElectricity supply .......................... 24V DC, 5ACoolant/fl ushing medium ............. WaterAir connection, air hose ............... 20 mm (3/4") IDWater connection, water hose ..... 9.5 mm (3/8") ID Dimensions: HxWxD mm .............. 730x350x300Weight .......................................... 43.5 kg

* With cooling tank unit 0,2-0,3 l/min.

Part No.

Intended for grinding all kinds of button bit.It is capable of handling threaded and taperedbutton bits upp to Ø 127 mm and DTH button bits up to Ø 250 mm (max. shank Ø 130 mm).

Pneumatic grinder without cooling unit 796-6205

Pneumatic grinder with cooling unit 796-6206

Accessories optionalBit holder insert for retrac-bits compl. 797-5502-50Guard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-locking system, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete, 10 l 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109

Complete grinding head 797-5130-10

Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10Air tool oil, 1 liter 797-5870-90

8-1_

900


GrindingButton bit grinder RG420H

RG420H

Technical data

Hydraulic pressure ...................... Max. 200 bar/ Min. 140 bar

Hydraulic-oil fl ow consumption ... 12 l/minAir pressure ................................. Max. 13 bar/ Min. 4 barAir consumption ........................... 5-6 l/secWater pressure ............................ Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Rated power (motor) ..................... 3.0 kWElectricity supply .......................... 24V DC, 5ACoolant/fl ushing medium ............. WaterHydraulic connection, hydr. hose . R 3/8" female threadAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm .............. 730x350x300Weight .......................................... 40 kg


Part No.

Intended for grinding all kinds of button bit.It is capable of handling threaded and cone-typebutton bits upp to Ø 127 mm and DTH button bits up to Ø 250 mm (max. shank Ø 130 mm).

Hydraulic grinder without cooling unit 796-6235

Hydraulic grinder with cooling unit 796-6236

Accessories optionalBit holder insert for retrac-bits compl. 797-5502-50Guard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-clamping device, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete, 10 l 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Priority fl ow divider for fi xed pumps 797-5414-01Grease gun 797-5870-20Grinding cups See page 121



8-1_

900


GrindingButton bit grinder RG420E

RG420E

Technical data

Air pressure ................................. Max. 13 bar/ Min. 4 barAir consumption ........................... 2-3 l/secWater pressure ............................ Max. 8 bar/Min. 4 barWater consumption ...................... 2-4 l/min *Rated power (motor) ..................... 1.5 kWCoolant/fl ushing medium ............. WaterAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm .............. 730x350x300Weight .......................................... 43 kg


Part No.


Electric powered grinder without cooling unit 796-6215-XX Electric powered grinder with cooling unit 796-6216-XX

Electric powered grinder

220-240 V 1 phase 50 Hz 796-62XX-50260 V 3 phases 50 Hz 796-62XX-51380-420 V 3 phases 50 Hz 796-62XX-52440 V 3 phases 50 Hz 796-62XX-55550 V 3 phases 50 Hz 796-62XX-56660 V 3 phases 50 Hz 796-62XX-57500 V 3 phases 50 Hz 796-62XX-58220-240 V 3 phases 50 Hz 796-62XX-59

220-290 V 3 phases 60 Hz 796-62XX-60380-480 V 3 phases 60 Hz 796-62XX-61 550 V 3 phases 60 Hz 796-62XX-65600 V 3 phases 60Hz 796-62XX-66

Accessories optionalBit holder insert for retrac-bits compl. 797-5502-50Guard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-clamping device, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete, 10 l 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28 Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109


Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10

8-1_

900


GrindingButton bit grinder RG420P/H/E Manual

RG420P/H/E Manual

Part No.


Air powered grinder without cooling unit 796-6300

Air powered grinder with cooling unit 796-6301

Hydraulic powered grinder without cooling unit 796-6330

Hydraulic powered grinder with cooling unit 796-6331

Electric powered grinder without cooling unit 796-6310-XX

Electric powered grinder with cooling unit 796-6311-XX

Electric powered grinder220-240 V 1 phase 50 Hz 796-63XX-50260 V 3 phases 50 Hz 796-63XX-51380-420 V 3 phases 50 Hz 796-63XX-52440 V 3 phases 50 Hz 796-63XX-55550 V 3 phases 50 Hz 796-63XX-56660 V 3 phases 50 Hz 796-63XX-57500 V 3 phases 50 Hz 796-63XX-58220-240 V 3 phases 50 Hz 796-63XX-59

220-290 V 3 phases 60 Hz 796-63XX-60380-480 V 3 phases 60 Hz 796-63XX-61 550 V 3 phases 60 Hz 796-63XX-65600 V 3 phases 60Hz 796-63XX-66

Accessories optionalGuard cover 797-5510-06Arm-locking mechanism, complete 797-5510-30Pneumatic bit-clamping device, complete 797-5510-40Bit holder for large drill bits, complete 797-5510-20Cooling/Flushing tank unit, complete 797-5488-75Mounting bracket (for drill rig) 797-5510-05Air pressure reducing valve (max.28/min.7 bar) 797-5910-28 Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109



8-1_105

Technical data Manual P Manual H

Manual E

Air pressure ................... Max. 13 bar Max. 13 bar Max. 13 bar Min. 6.5 bar Min. 4 bar

Min. 4 barAir consumption ............. 40-60 l/sec 2-3 l/sec 2-3 l/secHydraulic pressure ......... Max. 200 bar Min. 140 barOil consumption .............. 12 l/minWater pressure .............. Max. 8 bar Max. 8 bar Max. 8 bar Min. 4 bar Min. 4 bar

Min. 4 barWater consumption ........ 2-4 l/min * 2-4 l/min * 2-4 l/min *Rated power (motor) ....... 1.7 kW 3 kW 1.5 kWAir connection, hose ....... 3/4" 3/8" 3/8"Water connection, hose .. 3/8" 3/8" 3/8"Dimensions: HxWxD mm 730x350x300 730x350x300 730x350x300

Weight ............................... 41 kg 38 kg 41 kg



GrindingButton bit grinder RG440

RG440

Technical data

Air pressure ................................. Max. 13 bar/ Min. 6.5 barAir consumption ........................... 5-6 l/secRated power (motor) ..................... 1.5 kWWater pressure ............................. Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Coolant/fl ushing medium ............. WaterAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm ............. 990x670x795Weight .......................................... 95 kg


Part No.

Intended for grinding all kinds of button bit.It is capable of handling threaded and cone-typebutton bits upp to Ø 152 mm.

Grinder without cooling unit 796-6005-XX

Grinder with cooling unit 796-6006-XX

Electric powered grinder220-240 V 1 phase 50 Hz 796-6005-50260 V 3 phases 50 Hz 796-6005-51380-420 V 3 phases 50 Hz 796-6005-52440 V 3 phases 50 Hz 796-6005-55550 V 3 phases 50 Hz 796-6005-56660 V 3 phases 50 Hz 796-6005-57500 V 3 phases 50 Hz 796-6005-58220-240 V 3 phases 50 Hz 796-6005-59

220-290 V 3 phases 60 Hz 796-6005-60380-480 V 3 phases 60 Hz 796-6005-61 550 V 3 phases 60 Hz 796-6005-65600 V 3 phases 60Hz 796-6005-66

Accessories optionalBit mandrels. See manual. 797-5348-XX*Cooling/Flushing tank unit, complete, 10 l 797-5488-75Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109


Recommen ded lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10

* Bit mandrel for T38 bits, 797-5348-38 is included in delivery.

8-1_

97d


8-1_

97e

GrindingButton bit grinder RG460

RG460

Technical data

Air pressure ................................. Max. 13 bar/ Min. 6.5 barAir consumption ........................... 5-6 l/secRated power (motor) ..................... 1.5 kWWater pressure ............................. Max. 8 bar/ Min. 4 barWater consumption ...................... 2-4 l/min *Coolant/fl ushing medium ............. WaterAir connection, air hose ............... 9.5 mm (3/8") IDWater connection, water hose ..... 9.5 mm (3/8") IDDimensions: HxWxD mm ............. 990x670x795Weight .......................................... 95 kg


Part No.

Intended for grinding DTH bits up to Ø 280 mm.(max shank diameter 110 mm)

Grinder without cooling unit 796-6105-XX

Grinder with cooling unit 796-6106-XX

Electric powered grinder220-240 V 1 phase 50 Hz 796-6105-50260 V 3 phases 50 Hz 796-6105-51380-420 V 3 phases 50 Hz 796-6105-52440 V 3 phases 50 Hz 796-6105-55550 V 3 phases 50 Hz 796-6105-56660 V 3 phases 50 Hz 796-6105-57500 V 3 phases 50 Hz 796-6105-58220-240 V 3 phases 50 Hz 796-6105-59


Accessories optionalComplete bit holder for threaded bits 797-5503-60Cooling/Flushing tank unit, complete, 10 l 797-5488-75Assembly tools for O-ring replacement 797-5452Grinding gauge for button up to Ø 16 mm 795-1396Grease gun 797-5870-20Grinding cups See page 109


Recommen ded lubricantsGrease, 0.4 kg cartridge 797-5773-20Gear oil, 1 liter 797-5870-10


GrindingBit blaster RG500

RG500

Part No.

Fully automatic bit blaster for removing of excessive

steel from the bit face on all types of bits

from 33 mm to 195 mm in diameter.

Bit Blaster 796-9200-XX

Electric power 220-240 V 1 phase 50 Hz 796-9200-50260 V 3 phases 50 Hz 796-9200-51380-420 V 3 phases 50 Hz 796-9200-52440 V 3 phases 50 Hz 796-9200-55550 V 3 phases 50 Hz 796-9200-56660 V 3 phases 50 Hz 796-9200-57500 V 3 phases 50 Hz 796-9200-58220-240 V 3 phases 50 Hz 796-9200-59


Accessories optionalBit holders for threaded bits 797-5615-xx*Cyclone fi lter unit 796-9250-xx

*Note! No bit mandrels are included

8-1_113

Technical data

Air pressure ................................. 5-7 barAir consumption ........................... 5 bar 6 bar 7 bar 8 mm nozzle ................................. 47 l/s 57 l/s 63 l/s

9,5 mm nozzle ............................... 67 l/s 80 l/s 93 l/sRated power (motor) ..................... 0,3 kWBlast tank volume ......................... 30 l /100 kg Dimensions: HxWxD mm ............. 1650(1700)x800x1010 Weight .......................................... 350 kg

Technical data for cyclone fi lter unit

Air pressure ................................. 5-7 bar

Air consumption ........................... 5-6 l/sRated power (motor) ..................... 0,4 kWDimensions: HxWxD mm ............. 1700x500x750 Weight .......................................... 60 kg


GrindingCross bit grinder RG300

RG300

RG300 is intended for frontal grinding of cross bits up to Ø 64 mm.

Grinder RG300, with pneumatic 796-3201-XX 1)

bit holder.

1) The last two digits (XX) in the ordering code are used to specify the electrical equipment, see table.

260 V 3 phases 50 Hz 796-32XX-51380/420 V 3 phases 50 Hz 796-32XX-52440 V 3 phases 50 Hz 796-32XX-55550 V 3 phases 50 Hz 796-32XX-56660 V 3 phases 50 Hz 796-32XX-57500 V 3 phases 50 Hz 796-32XX-58220-240 V 3 phases 50 Hz 796-32XX-59

220-290 V 3 phases 60 Hz 796-32XX-60380-415 V 3 phases 60 Hz 796-32XX-61550 V 3 phases 60 Hz 796-32XX-65600 V 3 phases 60 Hz 796-32XX-66

Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, cross bits 126° 797-6035-06

Accessories optionalManual gauge-grinding unit 796-6050-50Semi-automatic gauge-grinding unit, (standard Cross D) 796-2960-XXTimer for gauge-grinder, 60 sec. 797-6015-56Pneumatic bit-holder without mandrel 797-6020Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Dressing template, straight (Cross D) 797-6035-45Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112

Recommended lubricantsAir tool oil, 1 litre 797-5870-90Grease, 0.4 kg cartridge 797-5773-20

8-1_112

Part No.

Technical data

Rated power .......................... 1.7 KWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m. Water pressure ...................... Max. 8 bar, Min. 4 bar

Dimensions: (HxWxD mm) ..... 1250x1120x1350 Weight .................................... 190 kg

Grinding units:Rated power .......................... 0,37 kW Stroke frequency 50Hz .......... 140 strokes/min Stroke frequency 60Hz .......... 168 strokes/min

NOTE! Grinding wheels and

mandrels are not included.



RG320

RG320 is intended for frontal andgauge grinding of cross bits up to Ø 64 mm.

RG320 with right mounted 796-3231-XX 1)

frontal and left mounted semi-automaticgauge grinding equipment with pneumatic bit holders


260 V 3 phases 50 Hz 796-32XX-51380/420 V 3 phases 50 Hz 796-32XX-52440 V 3 phases 50 Hz 796-32XX-55550 V 3 phases 50 Hz 796-32XX-56660 V 3 phases 50 Hz 796-32XX-57500 V 3 phases 50 Hz 796-32XX-58220-240 V 3 phases 50 Hz 796-32XX-59

220-290 V 3 phases 60 Hz 796-32XX-60380-415 V 3 phases 60 Hz 796-32XX-61550 V 3 phases 60 Hz 796-32XX-65600 V 3 phases 60 Hz 796-32XX-66

Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, cross bits 126° 797-6035-06Dressing template, straight 797-6035-45

Accessories optionalTimer for gauge-grinder, 60 sec. 797-6015-56Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112


8-1_114

Part No.

Technical data

Rated power .......................... 1.7 KWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m.Water pressure ...................... Max. 8 bar, Min. 4 bar

Dimensions: (HxWxD mm) 1250x1350x1350Weight .................................... 245 kg

Grinding units:Rated power .......................... 0,37 kWStroke frequency 50Hz .......... 140 strokes/minStroke frequency 60Hz .......... 168 strokes/min

Semiautomatic gauge grinding unit (796-2960-XX):Rated power .......................... 0,45 kWStroke frequency 50Hz .......... 93 strokes/minStroke frequency 60Hz .......... 112 strokes/minSpeed 50Hz............................ 120 r.p.m.Speed 60Hz ........................... 144 r.p.m. Weight .................................... 75 kg





RG340

RG340 is a frontal grinding machine. Intended for frontal grinding of cross bits up to Ø 64 mm.

RG340, with pneumatic 796-3301-XX 1)

bit holder


260 V 3 phases 50 Hz 796-330X-51380/420 V 3 phases 50 Hz 796-330X-52440 V 3 phases 50 Hz 796-330X-55550 V 3 phases 50 Hz 796-330X-56660 V 3 phases 50 Hz 796-330X-57500 V 3 phases 50 Hz 796-330X-58220-240 V 3 phases 50 Hz 796-330X-59

220-290 V 3 phases 60 Hz 796-330X-60380-415 V 3 phases 60 Hz 796-330X-61 550 V 3 phases 60 Hz 796-330X-65600 V 3 phases 60 Hz 796-330X-66

Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, cross bits 126° 797-6035-06

Accessories optionalPneumatic bit-holder without mandrel 797-6020Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112


8-1_100b

Technical data

Rated power .......................... 1.7 KWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m.Water pressure ...................... Max. 8 bar/ Min. 4 barDimensions: (HxWxD mm) ..... 1250x1350x1350Weight .................................... 210 kg

Grinding units:Rated power .......................... 2 x 0,37 kWStroke frequency 50Hz .......... 140 strokes/minStroke frequency 60Hz .......... 168 strokes/min



Part No.



RG360

RG360 is a frontal grinding machine. Intended for frontal grinding of X-bits up to Ø 76 mm.

RG360 with pneumatic bit holder 796-3601-XX 1)


260 V 3 phases 50 Hz 796-360X-51380/420 V 3 phases 50 Hz 796-360X-52440 V 3 phases 50 Hz 796-360X-55550 V 3 phases 50 Hz 796-360X-56660 V 3 phases 50 Hz 796-360X-57500 V 3 phases 50 Hz 796-360X-58220-240 V 3 phases 50 Hz 796-360X-59

220-290 V 3 phases 60 Hz 796-360X-60380-415 V 3 phases 60 Hz 796-360X-61550 V 3 phases 60 Hz 796-360X-65600 V 3 phases 60 Hz 796-360X-66

Accessories included in deliveryGrinding wheel dresser 796-1858Protective goggles 797-5771Dressing template, X-bits 75° 797-6035-07Dressing template, X-bits 105° 797-6035-08

Accessories optionalPneumatic bit-holder without mandrel 797-6020Foot pedal 797-5730-13Timer, 30 sec. 797-6015-60Spare rollers for wheel dresser 796-1867Grinding templates See page 112Grinding wheels See page 110/111Mandrels See page 112Grinding wheel dresser See page 112


Part No.

Technical data

Rated power .......................... 1.7 kWSpeed 50Hz............................ 1400 r.p.m.Speed 60Hz ........................... 1680 r.p.m.Water pressure ...................... max. 8 bar/ Min. 4 barDimensions (HxWxD mm) ...... 1250x1350x1350Weight .................................... 245 kg

Grinding units:Rated power .......................... 2 x 0,37 kWStroke frequency 50Hz .......... 140 strokes/minStroke frequency 60Hz ................168 strokes/min



8-1_100b


GrindingIntegral steel grinder RG100P

RG100P

Mobile, lightweight, pneumatic grinder.Intended for frontal and gauge grinding of chisel integral steels.

Complete grinder, air powered 796-5300

Accessories included in deliveryGrinding wheel for dry grinding 797-1227-15Protective goggles 797-5771T - hexagon wrench 797-5766-06

Accessories optionalGrinding wheels:For dry grinding 797-1227-15For wet grinding 797-1227-10In line oiler 797-5747-50Kit for grinding plug-hole drill steel steels 797-5489-50Mounting bracket (for drill rig) 797-5330-91Support for integral steels 797-5330-92Grinding template for chisel bit 795-1343Grinding template for plug-hole steels 795-1336

Recommended lubricantsAir tool oil, 1 litre 797-5870-90Grease, 0,4 kg cartridge 797-5773-20

8-1_73

W

dD

D 1

8-1_80

w

Part No.

Technical data

Air pressure ........................... Max 8 bar/ Min. 6 barAir consumption .................... 40-60 l/secRated power (motor) .............. 1.7 kWIdling speed ........................... 4900 r.p.m.Hose connections:Air, air hose ............................ 12.5 mm (1/2") IDAir or water hose for cooling . 9.5 mm (3/8") IDDimensions: HxWxD mm ....... 660x550x350Grinding wheel dimesions ..... 127x63x32 mm Weight inclusive of grinding wheel 16.5 kg

Cutting-edge radius .............. 80 mmCutting-edge angle ................ 110°

D = 127 mmW =

63 mmd = 32 mmD1 =

Grinding wheel


GrindingIntegral steel grinder RG100H

RG100H

Mobile, lightweight, hydraulic grinder.Intended for frontal and gauge grinding of chisel

integral steel.

Complete grinder, hydraulic powered 796-5330

Accessories included in deliveryGrinding wheel for dry grinding 797-1227-15Protective goggles 797-5771T - hexagon wrench 797-5766-06

Accessories optionalGrinding wheels:For dry grinding 797-1227-15For wet grinding 797-1227-10Kit for grinding plug hole drill steels 797-5489-50Mounting bracket (for drill rig) 797-5330-91Support for integral steels 797-5330-92Grinding template for chisel bit 795-1343Grinding template for plug hole steels 795-1336

Recommended lubricantsGrease, 0.4 kg cartridge 797-5773-20

W

dD

D 1

8-1_80

w

D = 127 mmW = 63 mmd = 32 mmD1 = 80 mmw = 50 mm

Part No.

Technical data

Hydraulic pressure ................ Max 200 bar/ Min. 140 barOil fl ow consumption ............. 12 l/minAir pressure ........................... Max 8 barAir consumption .................... 5-10 l/secRated power (motor) .............. 4 kWIdling speed ........................... 3700 r.p.m.Hose connections:Hydraulic, hydraulic hose ...... R 3/8" female threadAir, air hose ............................ 9.5 mm (3/8") IDWater, water hose ................. 9.5 mm (3/8") IDDimensions: HxWxD mm ....... 600x550x350Grinding wheel dimensions ... 127x63x32 mm

Cutting-edge radius .............. 80 mmCutting-edge angle ................ 110°

8-1_73C

Grinding wheel


GrindingIntegral steel grinder RG120E

RG120E

W

dD

D 1

8-1_80

w

8-1_61

Part No.

D = 152 mmW =

83 mmd = 63.5 mmD1 =

Electric grinder intended for frontal and gauge grinding of chisel integral steels.

Complete grinder (without water tray) 796-5012-XX1)


220-240 V 1 phase 50 Hz 796-5012-50260 V 3 phases 50 Hz 796-5012-51380/420 V 3 phases 50 Hz 796-5012-52440 V 3 phases 50 Hz 796-5012-55550 V 3 phases 50 Hz 796-5012-56660 V 3 phases 50 Hz 796-5012-57500 V 3 phases 50 Hz 796-5012-58220-240 V 3 phases 50 Hz 796-5012-59

220-290 V 3 phases 60 Hz 796-5012-60380-415 V 3 phases 60 Hz 796-5012-61550 V 3 phases 60 Hz 796-5012-65600 V 3 phases 60 Hz 796-5012-66

Accessories included in deliveryGrinding wheel for dry grinding 797-1252-15T - hexagon wrench 6 mm 797-5766-06Protective goggles 797-5771

Accessories optionalGrinding wheels:For dry grinding 797-1252-15For wet grinding 797-1252-10Water tray (plastic) 797-5346Support legs (set 2 pcs) 797-5347Grinding template for chisel bit 795-1343

Technical data

Air pressure ................................ Max 8 bar/ Min. 6 barAir consumption ......................... 20-45 l/secIdling speed ................................ 4200 r.p.m.Air motor ..................................... 1.5 kWHose connections:Air, air hose ................................. 12.5 mm (1/2") IDWater, water hose ...................... 9.5 mm (3/8") IDWeight inclusive of grinding wheel 38 kg

Cutting-edge radius ................... 80 mmCutting-edge angle ..................... 110°

Grinding wheel


GrindingIntegral steel grinder RG140P/H

8-1_104

RG140P/H

RG140P and 140H are intended for frontal and gauge grinding of integral steels vith 3 or 4 inserts and threaded or tapered bits.

Grinder RG140P, pneumatic powered 796-3800

Grinder RG140H, hydraulic powered 796-3830

Accessories included in deliveryGrinding wheel dresser 796-1858T - hexagon wrench 797-5766-06

Protective goggles 797-5771Pressing template for crossbit 797-6035-08

Accessories optionalGrinding wheel, dry, 132° 797-1185-28Grinding wheel, dry, straight for gauge grinding 797-1101-25Dressing template 4-inserts (cross bit) 797-6035-08Dressing template 3-inserts 797-6035-23Grinding template, cross bit 795-1343Spare rollers for wheel dresser 796-1867Mounting bracket (for drill rig) 797-5330-91

For Sandvik DC120 (Commando 120):Hydraulic mounting kit 797-5775-20

Recommended lubricantsAir tool oil (IXP), 1 litre 797-5870-90Grease (IXH), 0,4 kg cartridge 797-5773-20

Technical data Sanroc IXP Sanroc IXH

Hydraulic pressure ....................... – Max.200 bar

Min. 140 barOil fl ow consumption .................... – 12 l/minAir pressure .................................. Max 8 bar – Min. 6 barAir consumption ........................... 40-60 l/sec –Rated power ................................. 1.7 KW 4.0 KWIdling speed .................................. 3000 r.p.m. 3000 r.p.m.Dimensions: Grinder (HxWxD mm) .................... 250x285x395 250x240x395Grinding wheel 132°, DxWxd mm . 200x28x32 200x28x32Grinding wheel straight, DxWxd mm200x32x32 200x32x32Weight ........................................... 20 kg 18 kg

Air hose ......................................... 12.5 mm (1/2") ID –

Hydraulic hose .............................. – R 3/8"



Part No.


GrindingGrinding cups

Grinding cups for RG410-RG460 grinders

7 mm 797-5400-078 mm 797-5400-089 mm 797-5400-0910 mm 797-5400-1011 mm 797-5400-1112 mm 797-5400-1213 mm 797-5400-1314 mm 797-5400-1416 mm 797-5400-1618 mm 797-5400-18

7 mm 797-5295-078 mm 797-5295-089 mm 797-5295-0910 mm 797-5295-1011 mm 797-5295-1112 mm 797-5295-1213 mm 797-5295-1314 mm 797-5295-1416 mm 797-5295-1618 mm 797-5295-18

8-1_57

8-1_56

For button size Part No.

Sancup Super, (white)For redressing super-spherical buttons

Sancup Super, (red)For redressing R-ballistic buttons

Shank Ø 9 mm.

Shank Ø 9 mm.

Grinding cups for AC: LSD, CME: VS 200/ 220GTA, Jasco and others

7-8-9 mm 797-5356-0810 mm 797-5356-10

11 mm 797-5356-1112-13 mm 797-5356-1214 mm 797-5356-1416 mm 797-5356-16

8-9 mm 797-5366-0910 mm 797-5366-10

11 mm 797-5366-1112-13 mm 797-5366-1214 mm 797-5366-1416 mm 797-5366-16

Sancup (black)For redressing spherical buttons

Shank Ø 8 mm.* For older grinder remove O-ring before use (VS 200)

Sancup (black)For redressing ballistic buttons

Shank Ø 8 mm.* For older grinder remove O-ring before use (VS 200)


GrindingGrinding wheels

Grinding wheel for RG140P, RG140H (132°)

200 28 32 797-1185-28200 32 32 797-1101-32200 25 32 797-1101-25

dD

8-1_81

W

D W d Part No.

For cross bits 33-43 mm DryStraight wheel for gauge grinding

Dry

Grinding wheel, wet grinding

90° Cross bits 33-35 132° 300 23 32 797-1190-23 90° 38-41 132° 300 26 32 797-1190-2690° 43-45 132° 300 29 32 797-1190-2990° 48-51 132° 300 32 32 797-1190-32

75° X-bits 64 126° 300 35 32 797-1175-3575° 76 126° 300 44 32 797-1175-44105° 64 139° 300 48 32 797-1105-48105° 76 139° 300 58 32 797-1105-58D d

W

8-1_23

Bit insert Wheelangle mm angle D W d Part No.

Straight wheel for gauge grinding 35-76 300 32 32 797-1100-32


GrindingGrinding wheels

W

d

DD 1

8-1_24

w

Grinding wheel for RG100P, RG100H and RG120P, RG120E

125 63 32 80 50 797-1227-15125 63 32 80 50 797-1227-10

150 83 63.5 100 64 797-1252-15150 83 63.5 100 64 797-1252-10

D W d D1 w Part No.

For RG100For RG100

For RG120For RG120

Secoroc: Junior and Senior, AC: Teroc 1500/1501

200 102 32 150 80 797-1250-10Wet

D W d D1 w Part No.

W

d

DD 1

8-1_24

w


GrindingGrinding accessories

Part No.

Mandrel, complete for pneumatic bit holder, also for semi-automatic gauge-grinding unit

8-1_103

For R23 (29/32") thread 797-6020-23For R25 (1") thread 797-6020-25For R28 (1 1/8") thread 797-6020-28For R32 (1 1/4") thread 797-6020-32

For α330 thread 797-6020-33For R35 (1 3/8") thread 797-6020-35For R38/T38 (1 1/2") thread 797-6020-38For T45 (1 3/4") thread 797-6020-45Wheel dresser, complete 796-1858

Wheel dresser

8-1_37

- Shaft (1 pcs) 1) 796-1862- Bearing bushing (2 pcs) 1) 796-1863- Screw (6 pcs) 1) 796-1865- Cover (2 pcs) 1) 796-1866- 1 set of dresser rollers 1) 796-1867

1) Included in a complete unit.

For plug hole drill steels type 721-XXXX and 722-XXXX

795-1336

For buttons up to 16 mm

795-1396

For OD-bits

795-1340

795-1343

2 mm3 mmRadius 80 mm

Max height of antitaper

Carbideinsert

Whe

el

Whe

el

Whe

el

Inte

gral

sBi

ts0

0

10

10110

20304050607080

8-1_89

For integrals with cross bit / For cross and X-bits with diameter up to 115 mm / For integrals with chisel bit and motor drill steels

Pneumatic bit-holder, complete without mandrel for Sandvik RG300/320/340/360 grinders

8-1 99

797-6020

Auxiliary tools

Auxiliary tools

Page

Bit adapters ................................................................................. 115

Reduction couplings ................................................................... 115

Wrenches and knock-off-tools .................................................. 116

Fishing tools, thread grease and gauges .................................... 117

Drill steel straightener................................................................118


Auxiliary toolsBit adapters

LDF M

2-1_

158b

R23 R32 200 - 7 7/8” 35 1 3/8” 7837-3301

R25 R32 173 - 6 13/16” 45 1 3/4” 7832-3301

R28 R32 230 - 9 1/16” 40 1 37/64” 7839-3301

R32 T38 225 - 8 55/64” 45 1 49/64” 7833-4401R32 R38 225 - 8 55/64” 45 1 49/64” 7833-4301

T35 T38 250 - 9 27/32” 48 1 7/8” 7337-4401

R38 R32 270 - 10 41/64” 55 2 5/32” 7834-3303R38 T38 245 - 9 21/32” 55 2 5/32” 7834-4401

T38 R32 270 - 10 41/64” 57 2 1/4" 7334-3301T38 T45 285 - 11 7/32" 57 2 1/4" 7334-5401T38 R38 280 - 11 1/32” 57 2 1/4” 7334-4301

T45 T38 265 - 10 7/16" 63 2 31/64" 7335-4401T45 T51 285 - 11 7/32" 63 2 31/64" 7335-6401

T51 T45 285 - 11 7/32" 71 2 51/64" 7336-5401

Wrench fl at

mm

28.5

38

38

3838

38

44.544.5

44.544.544.5

3844.5

44.5

Reduction couplings

L

D

F2

2-1_

293b

F1

R32 R28 165 - 6 1/2” 44 1 47/64” 7993-0444R32 R25 160 - 6 1/4” 43 1 11/16” 7993-2443

R38 R32 170 - 6 3/4” 55 2 5/32” 7994-3455

T38 R32 195 - 7 11/16” 55 2 5/32” 7314-3555T38 R38 185 - 7 9/32” 55 2 5/32” 7314-4455T38 T45 220 - 8 43/64” 61 2 13/32” 7314-6261

T51 T45 218 - 8 19/32” 71 2 51/64” 7316-6271

Threads Dimensions Part No. L DF M mm ft in mm in

Threads Dimensions Part No. L DF1 F2 mm ft in mm in


Auxiliary toolsWrenches and knock-off-tools

Knock-off-tools for Hex 22 and Hex 25 pilot rods, type 7922-XXXX-XX

2-1_

114

795-1469

For integral drill steels and shank rods

600 1' 11 5/8" 19 3/4" 795-1407600 1' 11 5/8" 22 7/8" 795-1408600 1' 11 5/8" 28 1 1/8" 795-2423

8-1_1

5

D L


Hex 19Hex 22Hex 28

For extension rods

300 – 11 13/16" 25 1" 795-1431300 – 11 13/16" 28 1 1/8" 795-1492370 1' 2 9/16" 32 1 1/4" 795-1432370 1' 2 9/16" 38 1 1/2" 795-1494

380 1' 2 31/32” 65 2 7/12” 795-1495

620 2' 13/32" 35 1 25/64" 795-2476850 2' 9 15/32" 45 1 3/4" 795-1420

D

4-1_

33

L

D

4-1_

34

L

Hex 25, Round 32Hex 28

Hex 32, Round 39Round 46

DTH

Hex 35Round 52

Knock-off-tools for tapered bits

2-1_

485

795-1467 795-1468

Hex 22Hex 25

Pneumatic knock-off-tool for tapered bits

Complete unit 796-1400

Chisel (wear part) 797-5712-01Guide sleeve 797-5114-03

Technical data

Air pressure ............................... 6-8 barAir consumption ........................ 7-9 l/sAir hose ..................................... 12.5 mm (1/2") IDDimensions: (HxWxD mm) ......... 500x300x120Weight ....................................... 18 kg

8-1_111


Auxiliary toolsFishing tools, thread grease and gauges

Fishing sleeve

33 – 185 R22 795-1629 35 – 225 R22 795-1630 39 – 215 R25 795-1631 38 – 275 R25 795-1632 48 42.5 335 R28 795-1687 48 46 300 R32 795-1604 60 – 353 R38 795-1605 52 50 284 T35 795-1613 60 57.2 353 T38 795-1607 71 68 393 T45 795-1608 80 75.5 440 T51 795-1609 92 87.5 450 GT60 795-2601 89 84.5 450 GT60 795-2603102 92 410 ST68 795-1696

Dimensions Part No. D D1 L Thread

For catchingR22 Hex. rods

R22 coupling sleevesR25 Hex. rods

R25 coupling sleevesR28 Hex. rods/coupling sleeves

R32 round/Hex. rods/coupling sleevesR38 round rods/coupling sleevesT35 round rods/coupling sleeves

T38 round rods/coupling sleeves/MF-rodsT45 round rods/coupling sleeves/MF-rodsT51 round rods/coupling sleeves/MF-rods

GT60 rodsGT60 rods

ST68 tubes Ø87

Thread grease

8-1_19

215 – 170 – 795-1960300 – 380 – 795-196153/57 – 235 – 795-1962300 – 380 – 795-1963370 – 690 – 795-1967610 – 870 – 795-1964

Can 4.5 kgCan 18.0 kg

Tube 0.40 kgLow temperature grease, can 18.0 kg

Barrel 50 kgBarrel 240 kg

Fishing pike

10 4 160 R22 795-1600 12 4 200 R25 795-1601 14.8 4 220 R28 795-1686 19.4 4 280 R32 795-1606 18 8 237 R38 795-1611 19.4 8 237 T38 795-1676 25 8 275 T45 795-1681 27 15 285 T51 795-1690 57 24 500 ST58 795-1699 71 32 541 ST68 795-2600

For catchingR22 rods 1)

R25 rods 1)

R28 rods 1)

R32 rods 1)

R38 rods 2)

T38 rods 2)

T45 rods 2)

T51 rods 2)

ST58 tubes Ø76 2)

ST68 tubes Ø87 2)

1) Without fl ushing hole.2) With fl ushing hole.

D D18-1_18

L

D

8-1_

17

L

Gauges / Wear gauge for male and female threads

8-1_7 795-1336

Gauges / Chuck wear gauge

8-1_44

795-1343


Drill steel straightener for Hex19 to Round 52

8-1_ 90

796-2930

796-2930-52 796-2931

Manual/Hydraulic

Electric/Hydraulic, 380V/50Hz

Support leg, 1 piece

Part No.

Auxiliary toolsDrill steel straightener


Code information

Third fi gure group

Integral steels with reduced width of bit (small gauge steel) ................................................................................................... xxx-xxxx-50Integral steels with reduced width of bit, + tolerance (small gauge steel) ................................................................................ xxx-xxxx-5005Integral steels, Premium plus, H22, insert height 19 mm ....................................................................................................... xxx-xxxx-65

Shank rod, drilled for fl ushing tube 4.5-5 mm, packing .......................................................................................................... xxxx-xxxx-13Shank rod, drilled for fl ushing tube < 7 mm, no packing ......................................................................................................... xxxx-xxxx-11

Tapered rod, drilled for fl ushing tube < 7 mm, carburized ...................................................................................................... xxxx-6xxx-11Tapered rod, drilled for fl ushing tube < 7 mm, HF- hardened ................................................................................................. xxxx-11xx-11

Cross bit, cemented carbide grade 42 .................................................................................................................................. xxxx-xxxx-42

Tapered button bits, cemented carbide grade XT48 with ballistic buttons ............................................................................... xxxx-xxxx-B48

Small hole drilling tools

Bench drilling tools Third fi gure group

Insert bits, cemented carbide grade 11 .................................................................................................................................. xxxx-xxxx-11 Insert bits, cemented carbide grade 42 .................................................................................................................................. xxxx-xxxx-42

Button bits, cemented carbide grade MP 45, with spherical buttons ....................................................................................... xxxx-xxxx-S45Button bits, cemented carbide grade MP 45, with ballistic buttons .......................................................................................... xxxx-xxxx-R45Button bits, cemented carbide grade DP 65, with spherical buttons ....................................................................................... xxxx-xxxx-S65Button bits, cemented carbide grade DP 55, with ballistic buttons ......................................................................................... xxxx-xxxx-R55Button bits, cemented carbide grade MP 45, with ballistic buttons ......................................................................................... xxxx-xxxx-R45

Extension rod, Guide tube, carburized ................................................................................................................................... xxxx-xxxx-20Extension rod, HF- hardened ................................................................................................................................................ xxxx-xxxx-30MF-rod, for surface drilling .................................................................................................................................................... xxxx-xxxx-70

Third fi gure group

Cross bits, cemented carbide grade 42 ................................................................................................................................ xxxx-xxxx-42

Button bits, cemented carbide grade XT48 with spherical buttons .......................................................................................... xxxx-xxxx-S48Button bits, cemented carbide grade XT48 with ballistic buttons ............................................................................................. xxxx-xxxx-R48Button bits, cemented carbide grade DP 65 with spherical buttons ......................................................................................... xxxx-xxxx-S65Button bits, one extra hole for side fl ushing ............................................................................................................................ xxxx-xxxxA-xxx

Rods, carburized................................................................................................................................................................... xxxx-xxxx-20

Drifting and tunneling tools


Bit classifi cation code

H Very hard to hard rock > 2500 bar (250 MPa)M Medium hard rock 1500-2500 bar (150-250 MPa)S Soft rock < 1500 bar (150 MPa)

C Homogeneous (competent) rockF Fissured rock

V Very abrasive rock > 40% silicaA Abrasive rock 20-40% silicaN Non-abrasive rock 0-20% silica

_

_

Tools for long hole drilling underground Third fi gure group

Insert bits, cemented carbide grade 11 .................................................................................................................................. xxxx-xxxx-11 Insert bits, cemented carbide grade 42 .................................................................................................................................. xxxx-xxxx-42

Button bits, cemented carbide grade MP 45, with spherical buttons ....................................................................................... xxxx-xxxx-S45Button bits, cemented carbide grade MP 45, with ballistic buttons .......................................................................................... xxxx-xxxx-B45Button bits, cemented carbide grade DP 65, with spherical buttons ....................................................................................... xxxx-xxxx-S65Button bits, cemented carbide grade DP 65, with semi-ballistic buttons ................................................................................. xxxx-xxxx-R65Button bits, cemented carbide grade MP 45, with semi-ballistic buttons ................................................................................ xxxx-xxxx-R45

Extension rod, carburized ..................................................................................................................................................... xxxx-xxxx-20

Drill tube, carburized ............................................................................................................................................................ xxxx-xxxx-26Drill tube, carburized, with permanent back fl ow valve ........................................................................................................... xxxx-xxxx-46

MF-rod, carburized .............................................................................................................................................................. xxxx-xxxx-20

Code information


Safety information

Grinding of Cemented Carbide

Grinding or heating a cemented carbide product will produce dust or fumes of hazardous ingredients which can be inhaled, swal-lowed or come in contact with the skin or eyes.

The limiting ingredient in cemented carbide is, from a health and safety point of view, Cobalt. Another hazardous ingredient is Tungsten Carbide.

Cobalt is classifi ed as harmful - may cause sensitization by inhalation or skin contact. Inhalation or skin contact may also cause irritation.

Sensitive persons may experience an allergic reaction. Repeated inhalation of aerosols containing Cobalt may cause obstruction in the respiratory organs. Long term inhalation of increased concentrations may cause permanent disease.

Precautions

- Avoid formation and inhalation of dust.- Wet grinding is recommended instead of dry grinding.- Always use Exhaust Ventilation which is adequate to limit personal exposure well below the Occupational Exposure Limits.- Use Respiratory Protection if ventilation is not available or adequate.- Use Safety Goggles when necessary- Wear suitable Gloves and Protective Clothing.


Numerical index with weight table


Part No. Weight Package Page (kg) size (pcs)


714-0434-65 1,80 20 6714-0635-65 2,40 20 6714-0641-65 2,50 20 6714-0829 3,00 20 6714-0833-65 3,00 20 6714-0834-65 3,00 20 6714-0840-65 3,00 20 6714-1232-65 4,20 20 6714-1234-65 4,20 20 6714-1240-65 4,20 20 6714-1628-50 5,40 20 6714-1631 5,40 20 6714-1633-65 5,40 20 6714-1639-65 5,40 20 6714-1833-65 6,00 20 6714-1839-65 6,00 20 6714-2030 6,60 20 6714-2033-65 6,60 20 6714-2427-50 7,90 20 6714-2432-65 7,90 20 6714-2438-65 7,90 20 6714-3231 10,30 20 6714-3237-65 10,20 20 6714-4030 12,70 20 6714-4036-65 12,70 20 6714-4829 15,20 15 6714-4835-65 15,10 15 6714-5628-50 17,60 15 6714-5634-65 17,60 15 6714-6427-50 20,10 15 6714-6433-65 20,10 15 6714-7226-50 22,50 30 6714-7232-65 22,50 6714-8026-50 24,70 6714-8825-5005 27,00 6714-9625-5005 29,50 30 6

721-1517 0,60 5 10721-1620 0,70 5 10721-1622 0,70 5 10721-1922 0,80 5 10721-2020 0,78 5 10721-2420 0,80 5 10721-2820 0,90 5 10721-3120 1,00 10

724-0424 1,30 20 5724-0429 1,30 20 5724-0627 1,70 20 5724-0823 2,10 20 5724-0828 2,20 5724-0834 2,20 20 5724-1226 3,00 20 5724-1627 3,90 5724-2426 5,65 20 5

728-0424 1,40 20 5728-0429 1,40 20 5728-0828 2,30 20 5

7304-3550-01 5,40 1 787304-3590-03 4,10 1 77-78, 897304-3591-01 4,20 1 77-78, 897304-3593-01 4,70 1 77-787304-3652-01 3,80 2 787304-3655-01 6,35 1 797304-3656-01 4,45 2 78

7304-3825-02 9,90 797304-4200-30 3,00 2 767304-4500-60 2,75 2 767304-4700-01 4,00 2 847304-4700-50 3,30 2 847304-4706-01 4,70 1 847304-4720-01 3,80 2 827304-4723-01 4,10 2 827304-4780-01 6,35 807304-4791-01 6,00 807304-4993-01 5,50 2 797304-7426-01 6,25 807304-7500-60 3,90 2 80-81, 897304-7502-60 5,40 1 76, 827304-7525-19 5,40 817304-7526-80 6,30 1 807304-7531-01 3,90 1 857304-7532-01 5,90 2 867304-7535-02 4,60 1 857304-7536-01 4,30 1 857304-7537-01 5,50 1 867304-7541-02 6,55 867304-7543-60 3,60 2 80-817304-7554-01 5,30 1 857304-7557-01 5,60 1 857304-7576-01 6,90 1 867304-7577-02 8,40 1 867304-7581-60 5,20 807304-7583-40 5,80 897304-7585-01 5,45 1 857304-7586-01 5,90 85

7305-3591-01 5,10 1 77-787305-3593-01 5,80 1 77-787305-3655-01 6,10 1 797305-3690-02 6,90 797305-3826-02 10,25 797305-4791-01 6,25 807305-6008-01 8,90 1 877305-6010-01 9,70 877305-7400-01 9,10 1 867305-7414-01 8,85 807305-7417-01 9,50 807305-7520-01 5,60 1 837305-7525-19 5,50 1 817305-7526-80 6,60 1 807305-7532-01 6,30 1 867305-7537-01 5,80 1 867305-7541-02 6,90 867305-7546-19 7,80 817305-7551-01 7,60 1 867305-7557-01 5,90 1 857305-7576-01 7,20 1 867305-7577-02 8,60 1 867305-7586-01 6,20 85

7306-3655-02 6,80 797306-3690-03 7,20 797306-3692-01 9,50 797306-6008-01 9,30 1 877306-6010-02 10,10 877306-6014-02 11,90 877306-6019-02 13,90 877306-6021-02 11,20 887306-6022-02 13,30 887306-6025-02 15,90 877306-7528-02 8,60 83





7306-7530-02 16,10 837306-7551-02 8,10 86

7307-3576-01 767307-3593-01 4,50 787307-3652-01 3,70 2 787307-3656-01 4,15 787307-7535-02 4,45 857307-7557-01 5,55 857307-7585-01 5,25 857307-7586-01 5,60 85

7314-3555 2,30 5 1157314-3652 1,50 25, 297314-4455 1,90 5 1157314-6261 2,85 1 115

7316-3671 3,65 1 457316-6271 4,00 1 115

7324-4131-20 25,00 277324-4137-20 29,40 277324-4143-20 33,80 277324-4149-20 39,20 277324-4155-20 44,00 277324-4231-20 27,80 277324-4237-20 33,20 277324-4243-20 38,60 277324-4249-20 44,00 277324-4255-20 48,00 277324-4261-20 57,00 277324-4331C-30 24,10 15 407324-4712C-20 10,60 15 557324-4715C-20 13,30 15 557324-4718C-20 16,10 15 557324-4731-70 25,50 5 397324-4737-70 30,00 397324-4743-70 36,40 397324-6537-20 29,25 15 257324-6543-20 34,00 10 257324-6931-20 18,30 407324-7243-20 35,00 10 297324-7249-20 39,90 10 297324-7255-20 44,80 10 297324-8543-20 33,70 10 297324-8549-20 37,10 10 297324-8555-20 42,00 10 297324-8561-20 46,10 5 297324-8637-20 25,50 5 257324-8643-20 27,50 10 257324-9631-20 24,00 257324-9637-20 27,50 15 257324-9643-20 32,00 10 257324-9649-20 37,00 10 257324-9655-20 42,20 10 257324-9661-20 44,00 5 25

7325-7331C-30 32,90 10 437325-7337C-30 40,00 10 437325-7343C-30 47,00 5 437325-7361C-30 66,50 5 437325-7715C-20 17,60 10 577325-7718C-20 21,00 10 577325-7731-70 35,00 427325-7737-70 41,20 427325-7743-70 47,50 42

7326-5337C-30 50,00 10 457326-5343C-30 56,00 5 457326-5361C-30 85,00 7 457326-5515C-20 23,00 10 597326-5518C-20 27,00 10 597326-5537-70 50,50 10 457326-5543-70 56,50 10 457326-5561-70 87,00 10 45

7327-4718-20 16,10 537327-4731-20 25,40 5 31, 377327-4737-20 32,00 377327-4743-20 35,00 377327-5243-20 35,00 317327-5249-20 40,10 5 317327-5255-20 45,00 5 317327-5261-20 50,00 5 31

7328-6009-02 17,40 1 877328-6020-01 17,30 1 887328-6035-01 22,00 1 88

7329-3716-01 21,70 1 797329-3720-01 26,60 1 797329-6009-02 16,90 1 877329-6020-01 16,80 1 887329-6035-01 22,35 88

7334-3301 2,60 1 1157334-4301 3,35 1 1157334-5401 3,30 1 115

7335-4401 2,90 1 1157335-6401 3,70 1 115

7336-5401 3,80 1 115

7337-4401 1,90 1 115

7378-7615-26 33,20 10 617378-7618-26 41,00 61

7379-8715-26 40,00 10 627379-8715-46 40,00 10 627379-8718-26 47,00 10 62

7514-2664-R55 1,70 5 387514-2664-S45 1,70 5 387514-2670-S45 1,85 5 387514-2676-R55 2,30 5 387514-2676-S45 2,30 5 387514-2689-S45 3,00 3 387514-3864-S45 1,70 5 38, 547514-3864-S65 1,70 5 38, 547514-3876-S45 2,20 5 387514-3876-S65 2,20 5 387514-4064-11 2,05 5 397514-4076A-11 2,60 5 397514-5964-R55 1,65 5 38, 547514-5964-S45 1,65 5 38, 547514-5976-R55 2,30 3 387514-5976-S45 2,30 3 387514-7864-R55 2,00 5 38, 547514-7864-S45 1,95 5 38, 547514-7870-S45 2,40 5 39, 547514-7876-R55 2,90 3 397514-7876-S45 3,00 3 39





7514-7964-R55 1,85 5 39, 547514-7964-S45 2,00 5 39, 547514-7964-S45 2,00 5 547514-7976-R55 3,20 397514-7976-S45 3,10 3 39

7515-2602-S45 4,00 1 417515-2676-R55 2,50 5 417515-2676-S45 2,35 5 41, 567515-2689-R55 3,10 3 417515-2689-S45 3,00 3 417515-3876-S45 2,30 5 41, 567515-3876-S65 2,30 5 41, 567515-3889-S45 3,40 3 41, 567515-3889-S65 3,60 3 41, 567515-5902-R55 4,00 1 417515-5902-S45 4,00 1 417515-5976-R55 2,40 3 417515-5976-S45 2,45 3 41, 567515-5989-R55 3,20 3 417515-5989-S45 3,20 3 41, 567515-7802-S45 5,90 1 427515-7876-R55 3,20 3 417515-7876-S45 3,25 3 41, 567515-7876-S65 3,05 3 567515-7889-R55 4,30 3 427515-7889-S45 4,40 3 427515-7902-R55 6,00 1 427515-7902-S45 6,20 1 427515-7970-R55 2,85 427515-7976-R55 3,10 3 42, 567515-7976-S45 3,05 3 42, 567515-7989-R55 4,50 3 427515-7989-S45 4,50 3 42, 567515-8270-R45 4,10 3 427515-8270-R45 4,10 3 567515-8276-R45 3,15 3 42, 567515-8289-R45 4,75 3 427516-2602-S45 4,30 1 447516-2615-S45 5,50 1 447516-2627-S45 6,60 1 44

7516-2689-S45 3,60 3 44, 587516-4902-S45 6,10 1 447516-4915-S45 7,85 1 447516-4927-S45 10,20 1 447516-5902-R55 4,35 1 447516-5902-S45 4,45 1 447516-5915-S45 5,60 1 447516-5927-S45 6,00 1 447516-5989-R55 3,20 3 447516-5989-S45 3,60 3 44, 587516-7802-S45 5,80 1 447516-7815-S45 8,10 1 447516-7889-R55 4,15 3 447516-7889-S45 4,15 3 44, 587516-7902-R55 5,75 1 447516-7902-S45 5,75 1 447516-7915-R55 8,35 1 447516-7915-S45 8,15 1 447516-7927-S45 10,50 1 447516-7989-R55 4,35 3 44, 587516-7989-S45 4,25 3 44, 58

7517-7854-R45 1,30 37, 537517-7857-R45 1,50 37, 53

7525-8476-R65 3,40 1 60

7528-5652C-S65 1 617528-8489-R65 4,00 1 61

7529-5652C-S65 14,80 1 627529-6652-S45 8,90 1 627529-6902-S65 5,20 1 627529-7302-R65 5,65 1 627529-7315-R65 7,50 1 627529-8402-R65 5,20 1 627529-8415-R65 5,90 1 62

7600-6014-02 12,95 1 877600-6022-03 14,55 1 887600-6025-02 16,70 1 877600-6030-01 21,00 1 887600-6031-01 20,80 1 877600-7530-02 16,90 1 83

7610-1137-70 73,00 10 477610-1143-70 82,00 10 477610-1161-70 110,00 10 477610-1443-70 85,00 1 47

7620-3802-S45 6,00 1 467620-3815-S45 7,25 1 467620-3827-S55 8,85 1 467620-3892-S45 5,15 1 467620-3896-S45 5,30 1 467620-4792-R55 5,60 1 467620-4902-S45 7,25 1 477620-4915-S45 9,50 1 477620-4927-S55 12,60 1 477620-4940-S55 16,70 1 477620-4952-S55 20,00 1 477620-5902-S45 5,95 1 467620-5915-R55 7,30 1 467620-5915-S45 7,50 1 467620-5927-S55 9,45 1 467620-5940-S55 12,10 1 467620-5952-S55 13,75 1 467620-7902-R55 7,00 1 467620-7902-S45 7,10 1 467620-7915-R55 9,40 1 467620-7915-S45 9,40 1 467620-7927-S55 12,70 1 467620-7940-S55 16,15 4 467620-7996-S45 6,20 5 467620-8118-S55 10,05 5 477620-8702-R45 7,50 1 467620-8792-R45 6,05 1 46

7640-7653-70 111,50 1 477640-8716-70 39,30 1 477640-8743-70 106,00 1 47

7721-4802-S45 2,05 4 26, 307721-4802-S48 2,05 4 287721-4827-S45 3,50 3 26, 307721-4827-S48 3,50 3 287721-4889-S45 1,45 4 26, 307721-4889-S48 1,45 4 287722-4864-S45 0,85 5 7, 20-23, 267722-4876-S45 1,25 5 7, 20-23, 267722-4889-S45 1,70 4 7, 22-23, 26





7723-4802-S45 3,60 2 52, 557723-4827-S45 5,20 2 55

7732-1045-42 0,65 10 10, 137732-1051-42 0,80 10 137732-1435-42 0,45 10 13, 197732-1438-42 0,55 10 10, 13, 197732-1441-42 0,69 10 10, 13, 197732-5235-S48 0,40 10 13, 197732-5237-S48 0,45 10 197732-5238-R48 0,49 10 137732-5238-S48 0,49 10 13, 197732-5241-S48 0,52 10 13, 197732-5345F-R48 0,77 10 13

7733-1064-42 1,50 10 357733-1345A-42 0,80 10 247733-1451-42 1,05 10 35, 517733-2664-S45 1,65 5 357733-2676-S45 2,00 5 357733-5243-S48 0,70 10 247733-5245-S48 0,75 10 247733-5245-S65 0,75 10 247733-5248-S48 0,92 10 247733-5251-S48 0,97 10 247733-5251-S65 0,97 10 247733-5345-R48 0,77 10 247733-5345-S48 0,78 10 247733-5348-S48 0,95 10 247733-5351-R48 0,95 10 24, 35, 517733-5351-S48 0,96 10 24, 35, 517733-5357C-S48 1,15 10 35, 517733-5443-R48 0,69 10 247733-5445-R48 0,78 10 247733-5448-R48 0,92 10 247733-5451-R48 0,97 10 247733-5602-S45 3,20 1 267733-7851-R55 1,15 5 357733-7851-S45 1,15 10 357733-7851-S45 1,15 10 517733-7864-S45 2,10 5 357733-8251-R45 1,25 5 35, 517733-8257-R45 1,65 5 35, 51

7737-1435-42 0,45 10 127737-1438-42 0,50 10 127737-1633-11 0,40 10 127737-4438A-B48 0,45 10 127737-5235-R48 0,35 10 127737-5241-R48 0,45 10 127737-5345-R48 0,53 10 12

7738-1448-42 1,00 10 297738-5248-S48 0,90 10 297738-5251-S48 0,99 10 297738-5348A-R48 0,96 10 297738-5348A-S48 0,97 10 297738-5348-R48 0,99 10 297738-5348-S48 0,97 10 297738-5351-R48 0,99 10 297738-5351-S48 0,97 10 297738-5602-S45 3,15 1 307738-7854-R48 1,25 5 317738-7854-S48 1,20 5 317739-1438-42 0,55 10 16, 227739-1441-42 0,65 10 16, 22

7739-5238-R48 0,61 10 16, 227739-5238-S48 0,61 10 16, 227739-5241-S48 0,63 10 16, 227739-5243-S48 0,65 10 16

7764-1435-42 0,45 10 217764-1438-42 0,55 10 217764-1441-42 0,65 10 217764-1633-42 0,40 10 217764-4433-S48 0,30 10 217764-4435-S48 0,30 10 217764-5235-R48 0,45 10 157764-5237-S48 0,55 10 217764-5238-R48 0,45 10 157764-5238-S48 0,45 10 217764-5241-S48 0,50 10 21

7765-1438-42 0,55 10 237765-1441-42 0,65 10 237765-5238-R48 0,61 10 237765-5238-S48 0,61 10 237765-5241-S48 0,63 10 237765-5243-S48 0,65 10 23

7766-1345A-42 0,75 10 277766-1448-42 0,95 10 277766-5243-S48 0,65 10 277766-5245-S48 0,75 10 277766-5245-S65 0,75 10 277766-5248-S48 0,82 20 277766-5345A-R48 0,80 20 277766-5345A-S48 0,80 20 277766-5348A-R48 0,85 20 277766-5348A-S48 0,85 20 277766-5351A-R48 0,95 20 277766-5351A-S48 0,95 20 277766-5443-R48 0,65 20 277766-5445-R48 0,75 20 277766-5602-S45 3,15 20 28

7770-5233-B48 0,30 20 87770-5235-B48 0,30 20 87770-9028-42 0,25 20 87770-9030-42 0,30 20 87770-9032-42 0,30 20 87770-9035-42 0,30 20 8

7776-1932-B48 0,20 20 97776-1936-B48 0,20 20 97776-1938-B48 0,24 20 97776-1940-B48 0,30 20 97776-4432-B48 0,21 20 97776-4435-B48 0,25 20 97776-4438-B48 0,30 20 97776-4440-B48 0,30 20 97776-6438-B48 0,30 20 9

7795-5232-B48 0,20 20 87795-5235-B48 0,25 20 87795-5238-B48 0,30 20 87795-6428-B48 0,15 20 87795-6430-B48 0,15 20 8

7801-6103-13 1,10 1 11, 757801-6110-13 3,40 10 11





7802-6103-13 1,10 1 10, 13, 757802-6108-13 3,00 10 10, 137802-6110-13 3,50 10 10, 137802-7103-14 1,40 1 757802-7503-20 1,60 1 75

7803-3100-30 2,00 2 767803-3576-01 4,75 1 77, 837803-3588-01 3,35 2 76, 837803-3590-03 3,90 1 77, 897803-3591-01 4,10 1 77-78, 83, 897803-3593-01 4,60 1 77-787803-3602-30 2,10 2 847803-3652-01 3,70 2 787803-3656-01 4,10 2 787803-3670-02 4,70 1 787803-4200-30 2,60 2 767803-4700-01 3,70 2 847803-4700-50 2,70 2 847803-4703-01 3,60 2 897803-4725-01 3,30 1 827803-4726-01 2,75 2 827803-7500-61 3,00 2 80-81, 897803-7531-01 3,85 2 857803-7532-01 5,70 1 867803-7535-02 4,20 1 857803-7547-01 2,55 2 847803-7549-01 2,55 2 847803-7553-01 3,90 2 857803-7557-01 5,60 1 857803-7585-01 5,10 1 857803-7586-01 5,40 1 857803-7662-01 5,70 1 847803-7663-01 5,70 1 84

7804-3575-01 4,05 2 767804-3575-01 4,05 2 837804-3590-03 4,20 1 777804-3590-03 4,20 1 787804-3590-03 4,20 1 897804-3590-03 4,20 1 897804-3652-01 3,80 2 787804-3670-02 4,25 0 787804-4700-01 3,90 2 847804-4725-01 3,80 0 827804-4993-01 5,50 1 797804-7500-60 3,50 2 807804-7500-60 3,50 2 817804-7500-60 3,50 2 817804-7500-60 3,50 2 897804-7531-01 4,15 1 857804-7536-01 4,40 1 857804-7554-01 5,20 1 857804-7585-01 5,30 1 85

7805-6015 10,45 2 817805-7015 10,40 4 817807-6103-11 1,20 1 12, 757807-6124-11 7,70 1 127807-6132-11 11,50 4 127807-6136-11 12,50 1 127807-7103-11 1,30 1 12, 757807-7136-11 18,10 1 12

7809-7547-01 2,70 2 84

7814-7136-11 18,10 1 15

7821-1435 2,30 4 22-237821-2935 237821-3040 2,70 1 287821-3440 2,75 4 267821-5440 2,65 1 30

7822-1526 1,85 4 227822-2526 1,30 4 207822-2726 1,30 217822-2826 237822-3526 1,45 4 26

7823-2647 4,60 1 557823-3647 4,40 1 52

7832-3301 1,20 1 115

7833-4301 1,80 1 1157833-4401 1,85 1 115

7834-3303 2,50 1 1157834-4401 2,30 1 115

7837-3301 1,00 1 115

7839-3301 1,40 1 115

7851-1308-20 2,50 20 117851-1312-20 3,60 20 117851-1316-20 4,80 20 11

7852-2309-20 3,60 20 147852-2312-20 4,60 20 147852-2315-20 5,70 20 147852-2318-20 6,90 20 147852-2324-20 9,00 20 147852-2331-20 11,50 20 14

7853-1724-20 9,50 217853-1726-20 9,99 217853-1731-20 11,74 217853-1737-20 14,06 217853-1824-20 11,60 217853-1826-20 12,50 217853-1829-20 13,76 217853-1831-20 15,00 217853-2631-20 237853-2637-20 237853-3309-20 5,80 15 527853-3312-20 6,30 15 527853-3315-20 8,00 10 527853-3318-20 9,80 10 527853-3324-30 13,20 10 367853-3331-30 16,40 10 367853-3337-30 19,70 10 367853-5109-20 6,00 15 527853-5112-20 7,50 15 527853-5115-20 9,00 15 527853-5118-20 11,00 15 527853-5131-20 17,70 15 367853-5137-20 21,70 15 367853-6224-20 9,50 15 197853-6226-20 12,50 10 197853-7631-20 15,00 15 227853-7637-20 20,00 15 22





7854-8637-20 23,50 15 257854-8643-20 27,00 10 257854-8649-20 30,50 10 257854-9631-20 23,10 15 257854-9637-20 27,80 15 257854-9643-20 32,80 10 257854-9649-20 37,00 10 25

7857-4821-20 6,40 20 127857-4831-20 10,00 20 12

7859-2931-20 14,50 15 16

7870-1140-11 17,10 15 87870-1144-11 13,90 15 87870-1148-11 14,80 15 87870-1156-11 17,50 15 87870-1164-11 19,80 15 87870-1172-11 22,50 50 87870-1180-11 87870-5124-11 7,92 20 87870-5132-11 10,24 20 87870-6106-11 2,28 20 87870-6112-11 4,16 20 87870-6118-11 6,04 20 87870-6120-11 6,54 20 87870-6124-11 7,92 20 87870-6131-11 9,79 20 87870-6137-11 11,40 20 8

7876-6106-11 2,20 20 97876-6108-11 2,70 20 97876-6112-11 4,10 20 97876-6118-11 5,90 20 97876-6120-11 7,80 20 97876-6124-11 7,80 20 97876-6131-11 9,60 20 97876-6136-11 11,00 20 9

790-1100 34,00 1 70790-2100 4,50 1 70790-2200 4,50 1 70790-2300 2,00 1 71790-3100 42,00 1 69790-4100 52,00 1 69790-4200 76,00 1 69790-6100 45,00 1 71

791-4101 0,03 1 69791-4102 0,05 1 69791-4103 0,05 1 69791-4105 5,00 1 69, 71

7922-6108-11 3,30 20 77922-6112-11 4,70 20 77922-6116-11 5,60 20 77922-6120-11 7,00 20 77922-6124-11 7,90 20 7

795-1336 0,01 1 105795-1336 0,01 1 112, 117795-1340 0,01 1 112795-1343 0,02 1 105, 112795-1396 0,01 1 93-94, 96, 98, 112795-1407 4,20 1 116795-1408 3,10 1 116

795-1420 5,50 1 116795-1431 3,50 1 116795-1432 3,50 1 116795-1467 1,00 1 116795-1468 0,80 1 116795-1469 4,40 1 7, 116795-1492 3,10 1 116795-1494 3,45 1 116795-1495 5,20 1 116795-1600 0,21 1 117795-1601 0,30 1 117795-1604 1,65 1 117795-1605 3,90 1 117795-1606 0,60 1 117795-1607 3,90 1 117795-1608 6,00 1 117795-1609 8,40 1 117795-1611 0,93 1 117795-1613 1,70 1 117795-1629 0,51 1 117795-1630 0,73 1 117795-1631 0,70 1 117795-1632 0,84 1 117795-1676 0,93 1 117795-1681 1,50 1 117795-1686 0,50 1 117795-1687 3,00 1 117795-1690 2,00 1 117795-1696 10,90 1 117795-1699 4,90 1 117795-1960 4,90 1 117795-1961 18,00 1 117795-1962 0,55 1 117795-1964 240,00 1 117795-2423 4,30 1 116795-2476 5,70 1 116795-2600 10,00 1 117795-2601 10,20 1 117795-2603 1 117

7953-4618-20 16,00 15 36, 527953-4631-20 24,00 15 36

7955-5618-20 24,00 10 39, 557955-5637-20 48,00 10 39

7956-6318-21 28,00 10 42, 577956-6337-70 46,00 10 427956-7637-70 77,50 1 42

7957-7618-20 40,00 10 457957-7618-20 40,00 10 597957-7637-70 76,00 1 457957-8737-70 89,00 1 45

796-1400 0,00 1 116796-1858 2,00 1 101796-1858 2,00 1 112796-1862 0,05 1 112796-1863 0,02 1 112796-1865 0,20 1 112796-1866 0,01 1 112796-1867 0,25 1 101796-2930 50,00 1 118796-2930-52 60,00 1 118796-2931 5,00 1 118796-2960-XX 120,00 1 101





796-3201-XX 260,00 1 101796-3231-XX 380,00 1 102796-32XX-51 380,00 1 101796-32XX-51 380,00 1 102796-32XX-52 380,00 1 101796-32XX-52 380,00 1 102796-32XX-55 380,00 1 101796-32XX-55 380,00 1 102796-32XX-56 380,00 1 101796-32XX-56 380,00 1 102796-32XX-57 380,00 1 101796-32XX-57 380,00 1 102796-32XX-58 380,00 1 101796-32XX-58 380,00 1 102796-32XX-59 380,00 1 101796-32XX-59 380,00 1 102796-32XX-60 380,00 1 101796-32XX-60 380,00 1 102796-32XX-61 380,00 1 101796-32XX-61 380,00 1 102796-32XX-65 380,00 1 101796-32XX-65 380,00 1 102796-32XX-66 380,00 1 101796-32XX-66 380,00 1 102796-3301-XX 355,00 1 103796-330X-51 355,00 1 103796-330X-52 355,00 1 103796-330X-55 355,00 1 103796-330X-56 355,00 1 103796-330X-57 355,00 1 103796-330X-58 355,00 1 103796-330X-59 355,00 1 103796-330X-60 355,00 1 103796-330X-61 355,00 1 103796-330X-65 355,00 1 103796-330X-66 355,00 1 103796-3601-XX 335,00 1 104796-360X-51 335,00 1 104796-360X-52 335,00 1 104796-360X-55 335,00 1 104796-360X-56 335,00 1 104796-360X-57 335,00 1 104796-360X-58 335,00 1 104796-360X-59 335,00 1 104796-360X-60 335,00 1 104796-360X-61 335,00 1 104796-360X-65 335,00 1 104796-360X-66 335,00 1 104796-3800 22,00 1 108796-3830 18,00 1 108796-5012-50 46,00 1 107796-5012-51 38,00 1 107796-5012-52 43,00 1 107796-5012-55 38,00 1 107796-5012-56 46,00 1 107796-5012-57 38,00 1 107796-5012-58 38,00 1 107796-5012-59 38,00 1 107796-5012-60 38,00 1 107796-5012-61 43,00 1 107796-5012-65 38,00 1 107796-5012-66 38,00 1 107796-5012-XX 38,00 1 107796-5100 2,70 1 93796-5116 2,90 1 93796-5300 18,00 1 105796-5330 16,50 1 106

796-6005-50 95,00 1 98796-6005-51 95,00 1 98796-6005-52 95,00 1 98796-6005-55 95,00 1 98796-6005-56 95,00 1 98796-6005-57 95,00 1 98796-6005-58 95,00 1 98796-6005-59 95,00 1 98796-6005-60 95,00 1 98796-6005-61 95,00 1 98796-6005-65 95,00 1 98796-6005-66 95,00 1 98796-6005-XX 95,00 1 98796-6006-XX 95,00 1 98796-6050-50 50,00 1 101796-6105-50 96,00 1 99796-6105-51 96,00 1 99796-6105-52 96,00 1 99796-6105-55 96,00 1 99796-6105-56 96,00 1 99796-6105-57 96,00 1 99796-6105-58 96,00 1 99796-6105-59 96,00 1 99796-6105-60 96,00 1 99796-6105-61 96,00 1 99796-6105-65 96,00 1 99796-6105-66 96,00 1 99796-6105-XX 96,00 1 99796-6106-XX 96,00 1 99796-6205 48,00 1 94796-6206 56,00 1 94796-6215-XX 70,00 1 96796-6216-XX 74,00 1 96796-6235 43,00 1 95796-6236 55,00 1 95796-62XX-50 1 96796-62XX-51 1 96796-62XX-52 1 96796-62XX-55 1 96796-62XX-56 1 96796-62XX-57 1 96796-62XX-58 1 96796-62XX-59 1 96796-62XX-60 1 96796-62XX-61 1 96796-62XX-65 1 96796-62XX-66 1 96796-6300 43,00 1 97796-6301 46,00 1 97796-6310-XX 65,00 1 97796-6311-XX 70,00 1 97796-6330 38,00 1 97796-6331 43,00 1 97796-63XX-50 1 97796-63XX-51 1 97796-63XX-52 1 97796-63XX-55 1 97796-63XX-56 1 97796-63XX-57 1 97796-63XX-58 1 97796-63XX-59 1 97796-63XX-60 1 97796-63XX-61 1 97796-63XX-65 1 97796-63XX-66 1 97796-9200-50 350,00 1 100796-9200-51 350,00 1 100





796-9200-52 275,00 1 100796-9200-55 350,00 1 100796-9200-56 350,00 1 100796-9200-57 350,00 1 100796-9200-58 350,00 1 100796-9200-59 350,00 1 100796-9200-60 350,00 1 100796-9200-61 350,00 1 100796-9200-65 350,00 1 100796-9200-66 350,00 1 100796-9200-XX 350,00 1 100796-9250-xx 60,00 1 100

7970-1200-xx 2,40 1 667970-1500-xx 3,00 1 667970-1600-xx 3,20 1 667970-1800-xx 3,60 1 667970-2000-xx 4,00 1 667970-2100-xx 4,20 1 667970-2400-xx 4,80 1 667970-2700-xx 5,40 1 667970-3000-xx 6,00 1 667970-3300-xx 6,60 1 667970-3600-xx 7,20 1 667970-4000-xx 8,00 1 667970-4500-xx 9,00 1 667970-5000-xx 10,00 1 667970-5500-xx 11,00 1 667970-6000-xx 12,00 1 667970-600-xx 1,20 1 667970-900-xx 1,80 1 667970-P154D 0,66 1 667970-P156 1,05 1 667970-P158 1,35 1 66

797-1100-32 4,50 1 110797-1101-25 1,85 1 110797-1101-32 2,05 1 110797-1105-48 6,80 1 110797-1105-58 8,20 1 110797-1175-35 6,70 1 110797-1175-44 6,10 1 1107971-1800-xx 6,75 1 68797-1185-28 1,60 1 110797-1190-23 3,30 1 110797-1190-26 3,70 1 110797-1190-29 4,10 1 110797-1190-32 4,50 1 110

7971-2100-xx 7,90 1 68797-1227-10 1,05 1 105797-1227-10 1,05 1 111797-1227-15 1,00 1 105, 111

7971-2400-xx 9,00 1 68797-1250-10 3,35 1 111797-1252-15 1,85 1 1117971-2700-xx 10,20 1 687971-3000-xx 11,70 1 687971-3300-xx 12,40 1 687971-3600-xx 13,50 1 687971-4000-xx 15,00 1 687971-4500-xx 17,30 1 687971-5000-xx 19,20 1 687971-5500-xx 21,10 1 687971-6000-xx 22,90 1 687971-P154D 0,66 1 67

7971-P154D 0,66 1 687971-P156 1,10 1 677971-P156 1,10 1 687971-P158 1,39 1 677971-P158 1,39 1 68

7972-1800-xx 4,86 1 677972-2100-xx 5,67 1 677972-2400-xx 6,72 1 677972-2700-xx 7,29 1 677972-3000-xx 8,10 1 677972-3300-xx 8,91 1 677972-3600-xx 9,72 1 677972-4000-xx 10,80 1 677972-4500-xx 12,15 1 677972-5000-xx 13,50 1 677972-5500-xx 14,85 1 677972-6000-xx 16,20 1 67

797-5114-03 0,10 1 116797-5130-10 14,80 1 94797-5130-10 14,80 1 96797-5130-10 14,80 1 98797-5295-07 0,04 1 109797-5295-08 0,04 1 109797-5295-09 0,05 1 109797-5295-10 0,05 1 109797-5295-11 0,05 1 109797-5295-12 0,06 1 109797-5295-13 0,06 1 109797-5295-14 0,07 1 109797-5295-16 0,08 1 109797-5330-91 2,80 1 105797-5330-92 4,20 1 105797-5348-XX 1,00 1 98797-5356-08 0,05 1 109797-5356-10 0,05 1 109797-5356-11 0,05 1 109797-5356-12 0,05 1 109797-5356-14 0,05 1 109797-5356-16 0,05 1 109797-5366-09 0,05 10 109797-5366-10 0,05 10 109797-5366-11 0,05 10 109797-5366-12 0,05 10 109797-5366-14 0,05 10 109797-5366-16 0,00 10 109797-5400-07 0,04 1 109797-5400-08 0,04 1 109797-5400-09 0,05 1 109797-5400-10 0,05 1 109797-5400-11 0,05 1 109797-5400-12 0,06 1 109797-5400-13 0,06 1 109797-5400-14 0,07 1 109797-5400-16 0,08 1 109797-5400-18 0,10 1 109797-5452 0,06 1 93-94797-5452 0,06 1 96, 98797-5488-75 4,85 1 94797-5488-75 4,85 1 96, 98797-5488-85 5,95 1 93797-5489-50 1,50 1 105797-5502-50 1,05 1 94, 96797-5503-60 1 99797-5510-05 1,00 1 94, 96797-5510-06 7,20 1 94, 96




797-5510-20 4,00 1 94, 96797-5510-30 2,00 1 94, 96797-5510-40 3,00 1 94, 96797-5615-xx 1 100797-5712-01 1 116797-5730-13 1 101797-5747-50 1,50 1 93, 105797-5766-06 0,07 1 105797-5771 0,04 1 101, 105797-5773-20 1,00 1 94, 96, 98, 101797-5775-20 1 108797-5870-10 1,00 1 94, 96, 98797-5870-20 0,42 1 94, 96, 98797-5870-90 1,20 1 93-94, 101797-5910-28 1,23 1 94, 96797-6015-56 1 101797-6015-60 1 101797-6020 7,00 1 101, 103, 112797-6020-23 1 112797-6020-25 0,81 1 112797-6020-28 1 112797-6020-32 1,00 1 112797-6020-33 1 112797-6020-35 1,10 1 112797-6020-38 0,00 1 112797-6020-45 1,26 1 112797-6035-06 0,24 1 101797-6035-07 0,26 1 104797-6035-08 0,23 1 104797-6035-45 0,36 1 101, 102

7985-6315-26 28,00 10 607985-6318-26 32,00 10 60

7991-2031 0,45 10 11

7993-0444 1,20 5 1157993-2443 1,05 5 1157993-3644 0,90 5 20-23, 52

7994-3455 1,90 5 1157994-3655 1,70 5 25

7999-3640 0,77 5 16, 20

Notes

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................


Notes

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................


Notes

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................


Notes

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................


Notes

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................


Notes

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................

......................................................................................................................................................................


Ro

ck

drillin

g to

ols

To

p h

am

me

r pro

du

cts

www.sandvik.com

Sandvik Mining and Construction Tools ABSE-811 81 Sandviken, Sweden. Tel +46 26 26 20 00 Fax +46 26 26 23 00

HR-12281-ENG AB Sandvikens Tryckeri

Top hammer drilling tools Product catalogue

Products from Sandvik Mining and Construction Tools

Sand Vik

Documents

steel grade

small gauge

drop center4x10

small hole

long storage

shank adaptersatlas

button bit3x9

older grinder