Sales & Application - DeltaQ 2010.pdfSales & Application SINGLE PUMPS. AP 40 B 1 B 4 C 2 R 100 ... Outlet 1" OD Flange per SAE J518C Code 61 (Use #3 cover and "B" flange) SAE "C" two

DELTA^Q

DELTA^Q

DELTA^Q

DELTA^Q

DELTA^Q

DELTA^Q

DELTA^Q

DELTA^Q

AXIAL PISTON PUMPSPlant Location and Mailing Address10827 Tower Oaks Blvd.Houston, Texas 77070

AP40 SERIES

Please visit website @ www.deltaq.comEmail: [email protected]

Fax: (281) 807-4457 12-2008 Phone: (281) 807-1840 or (800) 650-3110

DELTA^QSales & ApplicationSINGLE PUMPS

AP 40 B 1 B 4 C 2 R 100

40 D Remote Load sense w/170 psi standby (4)

38 CA

35 M

30 CB

27 CC

25 PA

16 PB

Q

B R

T

1 W

2

3

4 1

5

2

6

7 3

8

17 6

18

19 7

20

21

10

B

C

13

1

4

5 R

9 L

A

B

C

CAY

CAX

* Red Denotes New Parts

SAE "C" Spline

SAE "C" Keyed - SAE "A" Spline rear drive

Short Differential (50 psi)

Torque Limiter (use with 'T' control)

ADAPTER: (Mounting)

(Use #3 cover and "B" flange)

SAE "BB" Spline - SAE "A" Spline rear drive

SAE "C" Keyed - SAE "BB" Spline rear drive

SAE "C" Keyed

SAE "BB" Spline

2 Spool CAY except w/Bypass (1 or 4)

Load Sense w/170 psi min standby (4)

NOTE: Standard Setting for Compensator is 2500 psi,

unless otherwise notated on order.

2 Spool Adj Press Comp & Adj Load Sense(1 or 4)

Pressure Settings

Assigned by factory for special variations

ROTATION: (viewed from shaft)

5

Counterclockwise

Dual Pressure Compensator (1 or 4)

Pressure Compensator (1 or 4)

Clockwise

Flow Limiter

VARIATION CODECONTROLS: (Required Construction in parenthesis)

MODEL/DISPL:

SAE "B" Spline

SHAFTS:

CONTROLS, cont'd:

2.7 Cubic Inch

2.5 Cubic Inch

Adj. Load Sense, Adj Press Comp (1 or4)

3.8 Cubic Inch

Loading 24 VDC (1 or 4)

Same as #3 with Min/Max vol. stop adj

COVERS:

REAR PORT, 4 Bolt Flange

Same as #3 except with rear drive SAE "B" drive

SIDE PORT, SAE 4-bolt flange code 61

Same as #2 with Min/Max vol. stop adj

Note: Use with shafts 17, 18, 19, 20 or 21

(Use #3 cover and "C" flange)

(Use #3 cover and "C" flange)

Shafts with rear drives:

SAE "C" Spline - SAE "A" Spline rear drive

Long Differential (350 psi)

SAE "BB" Spline - SAE "B" Spline rear drive

SAE "C" Keyed - SAE "B" Spline rear drive

CONSTRUCTION:

SAE "B" two bolt

1.6 Cubic Inch

3.0 Cubic Inch

3.5 Cubic Inch

Torque Limiter w/ Press Comp (5)

Standard Design with reduced noise level

SERIES:

Un-Loading 24 VDC (1 or 4)

Un-Loading 12 VDC (1 or 4)

Cover Plate

Loading 12 VDC (1 or 4)

Inlet 1 1/2" OD Flange per SAE J518C Code 61

REAR PORT, SAE O-Ring Ports

Inlet 1-7/8-12UN-2B(#24), Outlet 1-5/16-12UN-2B(#16)

Outlet 1" OD Flange per SAE J518C Code 61

Inlet 1 1/2" OD Flange per SAE J518C Code 61

Note: Rear "A" pad not available

Same as #10, except with Min/Max Vol Stops Adj.

Outlet 1" OD Flange per SAE J518C Code 61

(Use #3 cover and "B" flange)

SAE "C" two & four bolt

SAE "C" Spline - SAE "B" Spline rear drive

SAE "C" Spline - SAE "BB" Spline rear drive

SAE "B" Spline - SAE "A" Spline rear drive

Torque Limiter w/ Load Sense (5)

Flow Limiter

Load Sense w/350 psi min standby (4)

Note: Rear "A" pad not available

4.0 Cubic Inch ( 65.5cc)

ADJ. 2 SPOOL CONTROL