What’s in the box?..... What do I need to fit it?..... How to install the VHF on desktop and overhead..... How to install the VHF flush mount..... Drilling plan.......flush mount..... INSTALLATION GUIDE SAILOR 6215/6216 VHF DSC Thrane & Thrane A/S • [email protected]• www.thrane.com TT98-128470-THR-F A A B B 99-130248 Gasket Flush Mount Bracket (2 pcs.) Screw M4x45 TORX 20 (4 pcs.) Connect to LOUD HAILER (RED isolation on inner connector) Connect to EXT. SPEAKER (WHITE isolation on inner connector) Connect to POWER + (RED wire) Connect to POWER - (BLUE wire) Square Nut M4x7x2.2 (4 pcs.) Max wall thickness 26mm 99-130250 Remove material from shaded area only! 89mm 177mm R2.5mm x 4 Drilling plan.......on desktop and overhead..... Cable assembly for waterproof installation..... How to install the handmicrophone cradle..... 99-130249 4 x M4 or hole for self-tapping ø3.9 150mm 53mm 71mm 196mm 23mm 9mm Tilting ±20° 1. 2. 3. 4. Connect the 4 cable connections with rubber vulcanizing tape as shown ..... Power Drill Jigsaw Screwdriver TORX 20 Drill for M4 or Ø3.9 self-tapping Not Not Not Not Note! e! e! e! e! - Firmly tie back and secure any wires not used in order to avoid possibility for mutual shorting or shorting to ground! - To ensure waterproof sealing: If the surface isn’t plane and/or rigid remove the gasket and seal with silicone sealant between the VHF and the surface. U-Mounting Bracket Transceiver Gasket Flush Mount Bracket (2 pcs.) Sun Screen Fuse 6.3x3.2mm (10AT) User & Installation Manual Handmicrophone Cradle Wheel Knob (2 pcs.) Screw M4x45 TORX 20 (5 pcs.) Square Nut M4x7x2.2 (5 pcs.) Screw M4x12 TORX 20 (3 pcs.) Screw ø3.9x19 TORX 20 (3 pcs.) Screw M4x12 TORX 20 (5 pcs.) Screw ø3.9x19 TORX 20 (5 pcs.) USER & INSTALLATION MANUAL SAILOR 6215 VHF DSC Power Cable Connection Cable, 1 m
2
Embed
SAILOR 6215/6216 VHF DSC - Telemar · USER & INSTALLATION MANUAL SAILOR 6215 VHF DSC Connection Cable, Power Cable 1 m. Flush mount template Remove material from shaded area only!
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
What’s in the box?.....
What do I need to fit it?.....
How to install the VHF on desktop and overhead.....
How to install the VHF flush mount..... Drilling plan.......flush mount.....
Cable assembly for waterproof installation..... How to install the handmicrophone cradle.....
99-130249
4 x M4 or hole for
self-tapping ø3.9
150mm
53mm
71m
m
196mm
23mm
9mm
Tilting ±20°
1.
2.
3.
4.
Connect the 4 cable connections with rubber vulcanizing tape as shown .....
Power Drill Jigsaw ScrewdriverTORX 20
Drill for M4 orØ3.9 self-tapping
NotNotNotNotNote!e!e!e!e!- Firmly tie back and secure any wires not used in order to
avoid possibility for mutual shorting or shorting to ground!
- To ensure waterproof sealing:If the surface isn’t plane and/or rigid remove the gasket andseal with silicone sealant between the VHF and the surface.
IMPIMPIMPIMPIMPORORORORORTTTTTANANANANANT!T!T!T!T!If this template was printed from an electronicfile or copied, scaling (1:1) may not be correct.Consequently do not attempt to use a printedor copied template without prior checking ofdimensions.
NotNotNotNotNote!e!e!e!e!The SAILOR 6204/05 Control Speaker Microphone not yet available.
IMPIMPIMPIMPIMPORORORORORTTTTTANANANANANT!T!T!T!T!If this template was printed from an electronicfile or copied, scaling (1:1) may not be correct.Consequently do not attempt to use a printedor copied template without prior checking ofdimensions.
Mounting template for handmicrophone cradle.....
Brown, Pin 1, NMEA in +
Blue, Pin 2, NMEA in -
For waterproof installation use
rubber vulcanizing tape
GPS Cable (NMEA 0183)
99-130267IMPIMPIMPIMPIMPORORORORORTTTTTANANANANANT!T!T!T!T!Please note that the unused wires do not short-circuit.