S10-3c Take apart Presentation Bitland ShengXin 2010 / 4 / 29
S10-3c Take apart Presentation
BitlandShengXin2010 / 4 / 29
1. Release battery lock and latch, take the battery out of computer.1. Release battery lock and latch, take the battery out of computer.
Take apart
4X SCREWS M2.5*4.5 PH 0
Take apart2. Loosen 4 screws of HD door and RAM door, remove them;.2. Loosen 4 screws of HD door and RAM door, remove them;.
3. Loosen 1 screws of HD bracket then take it away;4. Take the RAM away from system module;
1X SCREWS M2*4 PH 0
Take apart
5. Loosen 4 screws of HD bracket
4 XSCREWS M3*3 PH 1
Take apart
6. Take off the Wi-Fi antenna, Loosen 1 screw of Wi-Fi and take it out;
1X SCREWS M2*3 PH 0
Take apart
7. Loosen 15 screws of Bottom Case
14 X SCREWS M2.5*6 PH 11 X SCREWS M2*4 PH 0
Take apart
8. Open LCD panel, take off the K/B cover
Take apart
9. Take keyboard out of 2 latches on the L and R sides of Top case, then pull out FPC
Take apart
10. Pull out LVDS cable, take WI-FI antenna out of Top case
Take apart
11. Loosen 2 screws of L/R hinge, tear down the LCD module
2 X SCREWS M2.5*6 PH 1
Take apart
12. Loosen 1 screw of MIC borad
1 X SCREWS M2*4 PH 0
System take apartSystem take apart
13. Loosen 2 screws on Top case14. Pull out TP FPC / Speaker cable / BT cable
2 X SCREWS M2.5*6 PH 1
BTBT
SpeakerSpeaker TPTP
System take apart
15.Divide Top case from Bottom case ,start with the right side
System take apart
16. Loosen 4 screws of Speaker cover ,remove speaker covers 17. Routing out cable and remove Blue Tooth and Speaker
4 X SCREWS M2*4 PH 0
System take apart
18. Upper lock and take away TP FPC19. Sprinkle frozen spray on TP, and divided TP from Top case quickly, or just knock TP down if not work anymore
System take apart
20. Routing out DC jack and pull out FPC of USB board ,take MB out of Bottom case.(start with I/O ,BOSS around RJ45 then battery connector)
11
22 33
System take apart
21. Loosen 1 screw of USB board
1 XSCREWS M2*4 PH 0
System take apart
22. Loosen 2 screw of L/R bracket, and Safe Lock
1 XSCREWS M2*3 PH 0 1 XSCREWS M2*5 PH 1
System take apart
23. Remove FAN cable from MB and loosen 2 screw of radiator24. Remove DC jack
2 XSCREWS M2*3 PH 0
System take apart
25. Remove 2 rubber and loosen 2 screws of LCD module and take away Bezel
2 X SCREWS M2*5 PH 1
LCD module take apart
26. Take magnet out of Bezle
LCD module take apart
27. Loosen 4 screws of L/R Hinge on Housing
4 X SCREWS M2*3 PH 0
LCD module take apart
28. Loosen 4 screws of L/R Hinge on LCD panel, this step should use support fixture29. Pull out LVDS cable
4 X SCREWS M2*3 PH 0
LCD module take apart
30. Take Camera out of Housing31. Take WI-FI antenna out of Housing
LCD module take apart
Tools size32.
Screw driver
PH 0 : 12x M2x3; 8x M2x4; 4x M2.5x4.5
PH 1 : 18x M2.5x6; 4x M3x3; 3x M2x5
Lock hinge support fixture
Flowchart拆电池拆硬盘盖
拆硬盘
拔WI-FI天线插头
2x M2.5x4.5 #0
拔喇叭, TP,BT插头
拆散TOPcase & BTM case
14x M2.5x6 #1
拆左右喇叭盖
4 x M2x4 #1
取喇叭
拆TP
冷冻剂
拆BT
拔USB板FPC
取USB板
1 x M2x4 #0
取主板
拔掉DC JACK
拔风扇线拆风扇
2 x M2x3 #0
拆Pick button
1x M2x4 #0
拆硬盘支架
4x M3x3 #1 拆键盘盖
拔FPC拆键盘 拔FPC
拆MIC板
1x M2x4 #0
拔LVDS取出WI-FI天线
拆SUB-LCD
4x M2.5x6 #1
拆Bezel左右2个螺丝盖
拆Bezel
2x M2x5 #1
拆合机磁铁
拔Camera插头
拆Camera拆LCD panel
4x M2x3 #0
拆WI-FI天线
拆L/R支架
4x M2x3 #0
拔LVDS cable
拆内存盖
2x M2.5x4.5 #0
拆内存条
Thank You !