Diagramasde.comdiagramas.diagramasde.com/audio/HCD-RV2 RV5 RV6 sm.pdf · 2012. 5. 1. · 1 Ver 1.2 2002. 11 Model Name Using Similar Mechanism NEW CD CD Mechanism Type CDM58E-30BD62
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
Ver 1.2 2002. 11
Model Name Using Similar Mechanism NEW
CD CD Mechanism Type CDM58E-30BD62
Section Base Unit Name BU-30BD62
Optical Pick-up Name A-MAX.3
Tape DeckModel Name Using Similar Machanism NEW
Section Tape Transport Mechanism TypeRV2: CWM43FF-05
RV5/RV6: CWM48RR-01
SERVICE MANUAL E ModelHCD-RV2/RV5/RV6
Tourist ModelHCD-RV5
HCD-RV2/RV5/RV6
Amplifier sectionHCD-RV2:The following measured at AC 120, 127, 220, 240 V,50/60 HzDIN power output (rated)
50 + 50 wattsContinuous RMS power output (reference)
60 + 60 watts (6 ohms at1 kHz, 10% THD)
HCD-RV6:The following measured at AC 120, 127, 220, 240 V,50/60 HzDIN power output (rated)
115 + 115 wattsContinuous RMS power output (reference)
140 + 140 watts (6 ohms at1 kHz, 10% THD)
HCD-RV5:The following measured at AC 120, 127, 220, 240 V,50/60 HzDIN power output (rated)
100 + 100 wattsContinuous RMS power output (reference)
120 + 120 watts (6 ohms at1 kHz, 10% THD)
SPECIFICATIONS
InputsHCD-RV2:GAME INPUT (VIDEO) (phono jack):
1 Vp-p, 75 ohmsGAME INPUT (AUDIO) (phono jacks):
voltage 450 mV,impedance 47 kilohms
MIC (phone jack): sensitivity 1 mV,impedance 10 kilohms
• HCD-RV2/RV5/RV6 is the tuner,deck, CD and amplifier section inMHC-RV2/RV5/RV6.
2
HCD-RV2/RV5/RV6
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
HCD-RV5/RV6:MD/VIDEO (AUDIO) IN (phono jacks):
voltage 450/250 mV,impedance 47 kilohms
GAME INPUT (VIDEO) (phono jack):1 Vp-p, 75 ohms
GAME INPUT (AUDIO) (phono jack):voltage 450 mV,impedance 47 kilohms
MIC (phone jack): sensitivity 1 mV,impedance 10 kilohms
OutputsPHONES (stereo mini jack):
accepts headphones of8 ohms or more
SPEAKER: accepts impedance of 6 to16 ohms
SURROUND SPEAKER (HCD-RV6 only)accepts impedance of 24ohms
MD/VIDEO (AUDIO) OUT (phono jacks):impedance 1 kilohms
VIDEO OUT (phono jack):1 Vp-p,impedance 75 ohms
Disc player sectionSystem Compact disc and digital
audio and video systemLaser Semiconductor laser
(λ=780 nm)Emission duration:continuous
Frequency response 2 Hz – 20 kHz (±0.5 dB)Wavelength 780 – 790 nmSignal-to-noise ratio More than 90 dBDynamic range More than 90 dBVideo color system format
FM tuner sectionTuning range 87.5 – 108.0 MHzAntenna FM lead antennaAntenna terminals 75 ohm unbalancedIntermediate frequency 10.7 MHz
AM tuner sectionTuning rangeMiddle Eastern and Philippine models:
531 – 1,602 kHz (with theinterval set at 9 kHz)
Other models: 531 – 1,602 kHz (with theinterval set at 9 kHz)530 – 1,710 kHz (with theinterval set at 10 kHz)
Antenna AM loop antennaAntenna terminals External antenna terminalIntermediate frequency 450 kHz
SpeakerHCD-RV2:Speaker system 3-way, 3-unit,
bass-reflex typeSpeaker unitsWoofer: 13 cm, cone typeTweeter: 5 cm, cone typeSuper Tweeter: 2 cm, dome typeNominal impedance 6 ohmsDimensions (w/h/d) Approx. 200 × 325 × 237 mmMass Approx. 3.6 kg net per
speaker
Front speaker SS-RV900 for HCD-RV6/RV5:Speaker system 3-way, 3-unit, bass-reflex
typeSpeaker unitsSub Woofer: 13 cm, cone typeWoofer: 13 cm, cone typeTweeter: 5 cm, cone typeNominal impedance 6 ohmsDimensions (w/h/d) Approx. 215 × 356 × 285 mmMass Approx. 4.5 kg net per
speaker
Surround speaker SS-RSV6 for HCD-RV6:Speaker system 2-way, 2-unit, bass-reflex
typeSpeaker unitsWoofer: 10 cm, cone typeTweeter: 5 cm, cone typeNominal impedance 24 ohmsDimensions (w/h/d) Approx. 150 × 325 × 220 mmMass Approx. 2.3 kg net per
speaker
GeneralPower requirementsSaudi Arabian model: 120 – 127 V, 220 V or
230 – 240 V AC,50/60 HzAdjustable with voltageselector
Thai model: 220 V AC, 50/60 HzOther models: 120 V, 220 V or 230 –
240 V AC, 50/60 HzAdjustable with voltageselector
Power consumptionHCD-RV2: 115 wattsHCD-RV5: 200 wattsHCD-RV6: 220 watts
MassHCD-RV2: Approx. 9.0 kgHCD-RV5: Approx. 10.0 kgHCD-RV6: Approx. 10.5 kg
Supplied accessories: AM loop antenna (1)Remote Commander (1)Batteries (2)FM lead antenna (1)Speaker pads (8)Video cable (1)
Design and specifications are subject to change withoutnotice.
3
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.
HCD-RV2/RV5/RV6
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.
Laser component in this product is capableof emitting radiation exceeding the limit forClass 1.
Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing• Keep the temperature of soldering iron around 270°C during
repairing.• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering
or unsoldering.
MODEL IDENTIFICATION
– BACK PANEL –
MODEL PARTS No.
RV2: E3, EA, MY, SP 4-238-649-6s
RV2: TH 4-238-649-7s
RV5: E3, EA, MY, JE, SP 4-238-649-8s
RV5: TH 4-238-649-9s
RV6: E3, EA, MY, SP 4-239-344-0s
RV6: TH 4-239-344-1s
• AbbreviationE3 : 240 V AC area in E modelEA : Saudi Arabia modelMY : Malaysia modelSP : Singapore modelTH : Thai modelJE : Tourist model
SETTING AND RELEASING THE CD DISC TRAY LOCKFUNCTIONThis set has a disc tray lock function to prevent discs fordemonstration at shops from theft. While this lock function is set,the tray will not be delivered out even when the OPEN/CLOSEbutton is pressed.
Setting method:Press the OPEN/CLOSE button while pressing the STOP button.After a few seconds, the message “LOCKED” will appear on thefluorescent indicator tube with the tray locked.
Releasing method:Just as the lock is set, press the OPEN/CLOSE button whilepressing the STOP button.After a few seconds, the message “UNLOCKED” will appear withthe lock released.
PARTS No.
4
TABLE OF CONTENTS
HCD-RV2/RV5/RV6
1. SERVICE NOTE ................................................................ 5
2. GENERALMain Unit (HCD-RV2) ............................................................ 6Remote Control (HCD-RV2) ................................................... 6Main Unit (HCD-RV5/RV6) ................................................... 7Remote Control (HCD-RV5/RV6) .......................................... 7
3. DISASSEMBLY3-1. Case (Top) ........................................................................... 93-2. Video Board ......................................................................... 93-3. CD (Door) ......................................................................... 103-4. Front Panel Section ........................................................... 113-5. Tape Mechanism Deck ...................................................... 123-6. Panel Board ....................................................................... 123-7. Key Board ......................................................................... 133-8. Sensor Board, DC Fan (FAN961) ..................................... 133-9. Main Board, Power Amp Board ........................................ 143-10. Base Unit ........................................................................... 143-11. Driver Board, Motor Board, Sensor (CD) Board .............. 15
–Sub Trans Section (HCD-RV6)– ..................................... 504-34. Schematic Diagram –Power Section (HCD-RV6)– .......... 514-35. IC Block Diagrams ............................................................ 52
5. EXPLODED VIEWS5-1. Main Section ..................................................................... 565-2. Front Panel Section ........................................................... 575-3. Main Board Section .......................................................... 585-4. CD Mechanism Deck Section ........................................... 595-5. Optical Pick-up Section ..................................................... 60
6. ELECTRICAL PARTS LIST ........................................ 61
5
HCD-RV2/RV5/RV6SECTION 1
SERVICE NOTE
1 Cut the fifteen melted-connection points with a cutting plier.
3 Cut the seven melted-connection points with a cutting plier.
2 PANEL board4 KEY board
PANEL board(eleven screw holes)
KEY board(six screw holes)
Screw hole
In order to re-install the panel board and the key board,fix them by using the screws (+BVTP 2.6 × 8 ) respectively.Screw in to the respective screw holes.Do not tighten the screws excessively.
* The panel board and the key board only are connected to the front panel by means of hot-melting the plastics.
Note for installing the panel board and the key board
REMOVING THE PANEL BOARD AND THE KEY BOARD
Hot melt
6
HCD-RV2/RV5/RV6SECTION 2GENERAL This section is extracted
from instruction manual.
(HC
D-R
V2)
(HC
D-R
V2)
7
HCD-RV2/RV5/RV6
(HC
D-R
V5/
RV
6)(H
CD
-RV
5/R
V6)
8
HCD-RV2/RV5/RV6SECTION 3
DISASSEMBLY
Note : Disassemble the unit in the order as shown below.
• AbbreviationE3 : 240 V AC area in E modelEA : Saudi Arabia modelMY : Malaysia modelSP : Singapore modelTH : Thai model
for printed wiring boards:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• x : parts mounted on the conductor side.• : Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.
• AbbreviationE3 : 240 V AC area in E modelEA : Saudi Arabia modelMY : Malaysia modelSP : Singapore modelTH : Thai model
Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.
– PANEL Board –
1
5MHz
IC701 3 (X1)
3Vp-p
– MAIN Board –
1
4.5MHz
IC102 1 (XIN)
1.8Vp-p
2
32.768kHz
IC601 qa (XCOUT)
2.8Vp-p
3
16MHz
IC601 qd (XOUT)
0.6Vp-p
– VIDEO Board –
1
33.8688MHz
IC505 <zb/> (XTAO)
1.1Vp-p
2
29MHz
IC505 <x/n> (CLKA)
0.6Vp-p
• Waveforms– BD Board –
1
2
IC103 6 (A), 8 (C)
Approx.160mVp-p
3
4
IC103 7 (B), 9 (D)
Approx.160mVp-p
IC103 qg (RFAC)
Approx.1Vp-p
IC103 wk (RFDCO)
Approx.0.6Vp-p
1818
HCD-RV2/RV5/RV6
1
A
B
C
D
E
F
G
H
I
2 3 4 5 6 7 8 9 10 11 12 13 14
C165
C113
R22
7
C108
C115
R12
2
C114
C111
C101
R228
C120
C102
C166
C163
C182
C164
C117
C103
C153
R12
6
R22
9R117
C109
C119
C104
C112
R125
R234
R235
C151
IC103
CN102
Q10
1
R176
R11
1
C110
R109
R11
3
Q102
R102
R22
6
R179
R12
3
R118
C213
R15
1
R236
IC102
R105
R103
R120
C107
R104
R12
4
R231
C118
R114
R152
R11
2
CN10
1
M102
M101
4-2. PRINTED WIRING BOARD — BD SECTION — • Refer to page 16 for Circuit Boards Location.
Ref. No. LocationIC102 C-12IC103 F-9
Q101 G-9Q102 C-9
• SemiconductorLocation
(Page 22)
19 19
HCD-RV2/RV5/RV6
• Refer to page 17 for Waveforms.
4-3. SCHEMATIC DIAGRAM — BD SECTION — • Refer to page 52 for IC Block Diagrams.
IC B/D
IC B/D
C113TP58
TP59
TP60
TP61
TP62
TP63
TP64
TP65
TP66
TP67
TP68
TP69
TP70
TP71
TP72
TP73
TP74
TP75
TP76
TP77
TP78
TP79
TP80
R234
TP21
TP14
TP56
TP49
TP23
M102
CN102
TP16
TP15
TP13
TP51
TP52
TP53
TP50
R227
R176
R111
TP22
C115
TP54
R122
C111
R228
C120
R109
R113
R102
C163
C182
R179
R123
R118
C213
TP100
R151
TP27
R105
R103
R120
R229
R117
R104
R124TP57
TP26
TP18
TP19
TP25
TP24
C112
R114
R152
TP17
TP55CN101
C151
C165
IC102
IC103
M101
R112
R226
R235
R236
C104C101
C102
C103
C107
C110
C108
R231
C109
R126
R125
C153
C166
C164
C114
C119
C118
Q102
Q101
C117
(Page 24)
2020
HCD-RV2/RV5/RV6
4-4. PRINTED WIRING BOARDS — CD SECTION — • Refer to page 16 for Circuit Boards Location.
1 2
A
B
C
D
E
F
G
3 4 5 6
IC71
1
IC70
1
14
14
1414
14
14
C
CN103
4
SENSOR (CD) BOARDMOTOR BOARD
DRIVER BOARD
(Page 30)
Ref. No. LocationD701 F-1
IC701 E-1IC711 B-5
• SemiconductorLocation
21 21
HCD-RV2/RV5/RV6
4-5. SCHEMATIC DIAGRAM — CD SECTION — • Refer to page 52 for IC Block Diagram.
IC B/D
CN711
R711 R713R712 IC711
S711
S701
M721 C721
CN722
CN721
R702
R701
D701 C702
IC701
CN702
CN701
C712
(Page 29)
2222
HCD-RV2/RV5/RV6
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11 12 13 14
EP200
EP202
EP201 CN101
C573JW523
JW52
4
C209
C366
IC505
R31
8
R310
C365
JW20
3
C597
FL201
FB25
2
L102C114
C582
C596
IC10
2
C544 C543
R55
8 R557
R556
R555
R554
R552
R55
1
C540
IC304
IC303
C570
IC30
2
R30
5
R30
2
R307R308
C305
C307
C308
C538
C315
R324
C309
C324
C524
C525
R501
R30
9
C326
C325
C503
C502
C551
R50
2
IC202
R533
C501
CN20
1
FB501
C567
R20
2
C301
C552
C568
C561
C584
RV501
C212
C210
C214
C258
C115
IC508
R11
5
R114
C211
R30
1
IC30
1 R323
R303
CN30
1
R10
2
R15
2
4-6. PRINTED WIRING BOARD — VIDEO SECTION — • Refer to page 16 for Circuit Boards Location.
4-23. PRINTED WIRING BOARD — POWER AMP SECTION (HCD-RV2) — • Refer to page 16 for Circuit Boards Location.
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11 12
41 41
HCD-RV2/RV5/RV6
4-24. PRINTED WIRING BOARD — TRANS SECTION (HCD-RV2) — • Refer to page 16 for Circuit Boards Location.
1
A
B
C
D
E
2 3 4 5 6 7 8 9 10 11
R913
R912
HPOWERAMP
BOARDCN501
JSUB TRANS BOARDCN2
ISUB TRANS BOARDCN903111-685-090-
(11)JW8 JW
931
LP97
5
JW918JW920
CN915CN9131
3
567891011121314 13
11
2 43
567424 R911
C912C913C911
D912C915
Q911
D913
R905
JW93
2
JW93
3
R916
R915
JW92
0
JW912
JW911
F919FH902 FH901
JW6
CN3
240V 220V 120VS901
VOLTAGESELECTOR
D911
JW935
FH908 F914 FH907FH910 F920 FH909
1
13WIRE901
T911POWER TRANSFORMAER
*JW6: TH MODEL JW911: E3,EA,JE,MY,SP MODEL CN3(2pin): TH MODEL (4pin): E3,EA,JE,MY,SP MODEL S901: E3,EA,JE,MY,SP MODEL F919: E3,EA,JE,MY,SP MODEL (CHASSIS)
8x Oversampling Digital Filterwith Function Controller
Enhanced Multi-LevelDeita-Sigma Modurator
Supply
I/F
MCLK
LATCLKDATA
DZFLDZFR
VCOM
AGND
9
8
10
D/A
D13D13D13D13
D8D9
D7D6D5D4D3D2D1D0
L D/AL
13
14
10 BITL-CHD/A
CONVERTER
10 BITLATCH
D/AL
D/AL
10 BITL-CHD/A
CONVERTER
10 BITLATCH
12
11
VCC
AO6
LD
CLK
DI
AO1
GND
5
7
6
2
1
3
4
VDD
AO4
AO5
RST
AO3
AO2
VSS
14BITSHIFT
REGISTER
ADDRESSDECODER
BUFFER,OP-AMP
5
4
3
CH2CH1
6
54
HCD-RV2/RV5/RV6
IC101 LA1845 (MAIN BOARD)
IC301 M61519FPD61G (MAIN BOARD)
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13
1211
21222324
S-CURVE
AM/FMIF
BUFFCOMP
TUNINGDRIVE
AMOSC
AMMIX
AMPF.AMP
AGC
AMIF
AMDET
BUFF
LEVELDET
FMIF FM
DET
REG GND
DEOODERANTI-BIRDIE
P-DETø
PILOTCANCEL
STEREOSW
VCO304kHz
FF38k
FF19k
π2
FF19k 0
PILOTDET
VCC
ALC
AFC
AM-R
F IN
AM-A
GCS.
MET
ER
AM D
ET-O
UT
DECO
DER
OUT
PLL-
IN
DECO
DER
IN
PILO
T CA
NCEL
R-OU
T
L-OU
T
AM-O
SC
OSC
AM.S
D
REG
AM IF
-IN GND
TUNE
D
STER
EO
FM-D
ET
VCC
IF-R
EQ M
UTE
AM/F
M
VCO
STOP
AM M
IX-O
UT
FM-IN
55
HCD-RV2/RV5/RV6
IC304 LA2615 (MAIN BOARD)
IC703 M65850FP (PANEL BOARD)
IC704 NJM2244M-TE2 (PANEL BOARD)
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
On/Off CONT2 CONT3 GND HPFC VREF L-IN R-IN
R-OUTL-OUTVccNCLPFCACGGURGLR
ANALOGSURROUND
VREF
++
OSCILLATOR
1/2 VCC
AUTORESET
LPF1
MAINCONTROL
A/D
20KBITSRAM
LPF2D/A
2 3 4 5 6 7 8
9101115 14 13 12
CLOCK
RESETMO
MID1 DO0
DO1
VCC
16
NC CLOC
K
REF
OP2I
N
OP2O
UT
LPF2
IN
LPF2
OUT
LPF1
IN
1
NC
LPF1
OUT
OP1O
UT
OP1I
N
CC1
CC2
GND
1
2
BIAS3
4
8
7
6
5
VIN1
SW1
VIN2
SW2
GND
VOUT
VCC
VIN3
56
HCD-RV2/RV5/RV6SECTION 5
EXPLODED VIEWS
NOTE:• The mechanical parts with no reference
number in the exploded views are not supplied.• Items marked “*” are not stocked since
they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.
• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.
• Accessories are given in the last of thisparts list.
• AbbreviationE3 : 240 V AC area in E modelEA : Saudi Arabia modelMY : Malaysia modelSP : Singapore modelTH : Thai model
Ref. No. Part No. Description Remark
5-1. MAIN SECTION
Ref. No. Part No. Description Remark
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
CDM58E-30BD62
#1
#1
JK303
#5
#1
#5
#1
#1
#1#1
#1#1
#1
#1
#1
#2
#1
#5
#1
#2
4
3
136
14
12
11
10
1
1
2
2
5
Front Panelsection
Main board section
FAN961
notsupplied
notsupplied
7
89
A
A
1 3-363-099-01 SCREW (CASE 3 TP2) (RV2/RV6)2 3-363-099-41 SCREW (CASE 3 TP2)3 4-224-549-21 CASE (SIDE-L)4 4-238-616-21 DOOR, CD (RV2)4 4-238-616-31 DOOR, CD (RV5)
4 4-238-616-41 DOOR, CD (RV6)5 4-224-550-01 CASE (TOP) (RV6)5 4-224-550-41 CASE (TOP) (RV2)5 4-224-550-81 CASE (TOP) (RV5)6 1-823-899-11 WIRE (FLAT TYPE) (28 CORE)
7 1-685-103-11 SENSOR BOARD (RV5)7 1-685-111-11 SENSOR BOARD (RV6)8 1-685-094-11 SUB TRANS BOARD (RV2)8 1-685-102-11 SUB TRANS BOARD (RV5)8 1-685-110-11 SUB TRANS BOARD (RV6)
9 1-685-089-11 SURROUND BOARD (RV6)
10 1-685-096-11 VIDEO OUT BOARD (RV2)10 1-685-104-11 VIDEO OUT BOARD (RV5)10 1-685-112-11 VIDEO OUT BOARD (RV6)11 4-238-649-61 PANEL, BACK (RV2:E3,EA,MY,SP)11 4-238-649-71 PANEL, BACK (RV2:TH)
11 4-238-649-81 PANEL, BACK (RV5:E3,EA,JE,MY,SP)11 4-238-649-91 PANEL, BACK (RV5:TH)12 4-224-548-61 CASE (SIDE-R)13 A-4676-362-A VIDEO BOARD, COMPLETE14 1-590-578-11 WIRE (FLAT TYPE) (19 CORE)
53 X-4954-905-1 DOOR (B) ASSY, CASSETTE (RV6)54 X-4954-788-1 DOOR (A) ASSY, CASSETTE (RV2)54 X-4954-848-1 DOOR (A) ASSY, CASSETTE (RV5)54 X-4954-904-1 DOOR (A) ASSY, CASSETTE (RV6)55 4-233-980-01 FOOT, RUBBER
56 4-238-609-71 DISPLAY (WINDOW) (RV2)56 4-238-638-31 DISPLAY (WINDOW) (RV5/RV6)57 4-239-346-01 SPRING (L), CASSETTE DOOR58 4-224-104-41 DAMPER59 1-685-098-11 MIC BOARD (RV2)
59 1-685-106-11 MIC BOARD (RV5)59 1-685-114-11 MIC BOARD (RV6)60 X-4954-787-1 PANEL ASSY, FRONT (RV2)60 X-4954-847-1 PANEL ASSY, FRONT (RV5)60 X-4954-903-1 PANEL ASSY, FRONT (RV6)
0T911 1-437-222-11 TRANSFORMER, POWER (RV5:E3,JE,MY,SP,TH)0T911 1-437-764-11 TRANSFORMER, POWER (RV2:E3,MY,SP,TH)0T911 1-437-765-11 TRANSFORMER, POWER (RV6:E3,MY,SP,TH)0T911 1-437-831-11 TRANSFORMER, POWER (RV2:EA)
0T911 1-437-832-11 TRANSFORMER, POWER (RV5:EA)0T911 1-437-833-11 TRANSFORMER, POWER (RV6:EA)
A-4676-995-A MAIN BOARD, COMPLETE (RV2:E3,MY,SP)A-4729-270-A MAIN BOARD, COMPLETE (RV5:E3,JE,MY,SP)A-4729-402-A MAIN BOARD, COMPLETE (RV6:E3,MY,SP)A-4730-979-A MAIN BOARD, COMPLETE (RV2:EA)A-4730-982-A MAIN BOARD, COMPLETE (RV2:TH)
A-4730-986-A MAIN BOARD, COMPLETE (RV5:EA)A-4730-988-A MAIN BOARD, COMPLETE (RV5:TH)A-4730-990-A MAIN BOARD, COMPLETE (RV6:EA)A-4730-992-A MAIN BOARD, COMPLETE (RV6:TH)
FB2 1-216-864-11 METAL CHIP 0 5% 1/10WFB3 1-216-864-11 METAL CHIP 0 5% 1/10WFB4 1-550-907-21 BEAD, FERRITE (CHIP)FB5 1-216-864-11 METAL CHIP 0 5% 1/10WFB6 1-550-907-21 BEAD, FERRITE (CHIP)
FB7 1-216-864-11 METAL CHIP 0 5% 1/10W
< FRONT END >
FE101 1-693-478-11 FRONT END (3 GANG)
66
HCD-RV2/RV5/RV6
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MAIN
< EARTH TERMINAL >
* GND1 1-537-738-21 TERMINAL, EARTH
< IC >
IC101 8-759-828-33 IC LA1845IC102 6-702-258-01 IC LC72121IC201 6-702-130-01 IC HA12237FIC301 6-702-422-11 IC M61519FPD61GIC302 8-759-710-97 IC NJM4565M-D
IC304 8-759-652-01 IC LA2615 (RV5/RV6)IC601 6-801-340-01 IC M30620MCN-A02FPIC602 6-700-915-01 IC SN74AHCT04PWRIC661 8-759-533-04 IC M62703ML-E1IC681 8-759-039-69 IC uPC7805AHF
IC682 6-701-760-01 IC uPC3504AHFIC683 8-759-088-08 IC uPC7812AHFIC684 8-759-701-59 IC NJM78M09FAIC685 8-759-039-69 IC uPC7805AHF
< IFT >
IFT101 1-435-848-12 TRANSFORMER, IF (CERAMIC FILTER)
IC701 6-801-360-01 IC uPD780232GC-059-8BTIC702 8-759-710-97 IC NJM4565M-DIC703 8-759-496-40 IC M65850FPIC704 8-759-295-90 IC NJM2244M-TE2
< JACK >
JK701 1-691-293-21 JACK (PHONES)JK704 1-815-684-11 JACK, PIN 3P (GAME INPUT
VIDEO/AUDIO,L/R)
< DIODE >
LED701 8-719-058-04 LED SEL5223S-TP15 (?/1)LED702 8-719-057-97 LED SEL5923A-TP15 (GAME)LED703 8-719-057-97 LED SEL5923A-TP15 (TAPE A/B)LED704 8-719-057-97 LED SEL5923A-TP15 (CD)LED705 8-719-057-97 LED SEL5923A-TP15 (TUNER/BAND)
IC701 6-801-360-01 IC uPD780232GC-059-8BTIC702 8-759-710-97 IC NJM4565M-DIC703 8-759-496-40 IC M65850FPIC704 8-759-295-90 IC NJM2244M-TE2
< JACK >
JK701 1-691-293-21 JACK (PHONES)JK704 1-815-684-11 JACK, PIN 3P (GAME INPUT
VIDEO/AUDIO,L/R)
< DIODE >
LED701 8-719-058-04 LED SEL5223S-TP15 (?/1)LED702 8-719-057-97 LED SEL5923A-TP15 (GAME)LED703 8-719-057-97 LED SEL5923A-TP15 (TAPE A/B)LED704 8-719-057-97 LED SEL5923A-TP15 (CD)LED705 8-719-057-97 LED SEL5923A-TP15 (TUNER/BAND)
IC701 6-801-360-01 IC uPD780232GC-059-8BTIC702 8-759-710-97 IC NJM4565M-DIC703 8-759-496-40 IC M65850FPIC704 8-759-295-90 IC NJM2244M-TE2
< JACK >
JK701 1-691-293-21 JACK (PHONES)JK704 1-815-684-11 JACK, PIN 3P (GAME INPUT
VIDEO/AUDIO,L/R)
< DIODE >
LED701 8-719-058-04 LED SEL5223S-TP15 (?/1)LED702 8-719-057-97 LED SEL5923A-TP15 (GAME)LED703 8-719-057-97 LED SEL5923A-TP15 (TAPE A/B)LED704 8-719-057-97 LED SEL5923A-TP15 (CD)LED705 8-719-057-97 LED SEL5923A-TP15 (TUNER/BAND)
LED706 8-719-057-97 LED SEL5923A-TP15 (MD (VIDEO))
IC102 8-759-701-40 IC NJM3404AM-T1IC201 6-700-399-01 IC uPC2925T-E1IC202 8-759-460-72 IC BA033FP-E2IC301 8-759-514-57 IC BA7046FIC302 8-759-530-30 IC TC74VHCU04FT(EL)
VIDEO
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
82
HCD-RV2/RV5/RV6
IC303 8-759-662-94 IC NJM2255M(TE2)IC304 8-759-711-47 IC NJM2209MIC307 6-702-001-01 IC BD7600FV-E2IC504 8-759-825-13 IC PCM1748E/2KIC505 8-752-417-93 IC CXD1887R
IC506 6-702-000-01 IC BU2507FV-E2IC507 6-702-572-01 IC VG3612816BT-7LIC508 6-801-401-01 IC MR27V401E-066MAZ020
< JUMPER RESISTOR >
JW203 1-216-864-11 METAL CHIP 0 5% 1/10WJW301 1-216-864-11 METAL CHIP 0 5% 1/10WJW523 1-216-864-11 METAL CHIP 0 5% 1/10WJW524 1-216-864-11 METAL CHIP 0 5% 1/10W
FAN961 1-763-072-11 FAN, DC (RV5/RV6)0T911 1-437-222-11 TRANSFORMER, POWER (RV5:E3,JE,MY,SP,TH)
0T911 1-437-764-11 TRANSFORMER, POWER (RV2:E3,MY,SP,TH)0T911 1-437-765-11 TRANSFORMER, POWER (RV6:E3,MY,SP,TH)0T911 1-437-831-11 TRANSFORMER, POWER (RV2:EA)0T911 1-437-832-11 TRANSFORMER, POWER (RV5:EA)0T911 1-437-833-11 TRANSFORMER, POWER (RV6:EA)
M721 A-4672-826-A MOTOR ASSY (OPEN/CLOSE)
VIDEO OUTVIDEO
Ref. No. Part No. Description Remark
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
84
HCD-RV2/RV5/RV6
MEMO
E ModelHCD-RV2/RV5/RV6
Tourist ModelHCD-RV5SERVICE MANUAL
Ver 1.2 2002. 11
SUPPLEMENT-1File this supplement with the service manual.
Subject : Addition of Test Mode, Mechanical Adjustments,Electrical Adjustments, IC Pin Function Description,and Block Diagrams.
1. TEST MODE[Cold Reset]• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returningthe set to the customer.
Procedure:1. Press three buttons x , ENTER (HCD-RV5/RV6) or
GROOVE (HCD-RV2), and ?/1 simultaneously.2. The fluorescent indicator tube display “COLD RESET” and the
set is reset.
[Hot Reset]1. Press three buttons x , GAME EQ , and DISPLAY simulta-
neously.2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset
[Tuner Step Change] (Except for European and Middle Easternmodels)• A step of AM channels can be changed over between 9 kHz and
10 kHz.Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “TUNER”, and press TUNER/BAND but-
ton to select the BAND “AM”.3. Press ?/1 button to turn the set OFF.4. Press ENTER and ?/1 buttons simultaneously, and the dis-
play of fluorescent indicator tube changes to “AM 9 k STEP” or“AM 10 k STEP”, and thus the channel step is changed over.
[VIDEO/MD Function Change]• Change of function VIDEO or MD ( also the input level changes).Procedure:1. Press ?/1 button to turn the set ON.2. Press VIDEO (MD) and ?/1 buttons simultaneously, and the
display of fluorescent indicator tube changes to “MD” or“VIDEO”, and thus the channel step is changed over.
3. Press ?/1 button to turn the set OFF.
[GC Test Mode]• This mode is used to check the FL tube, LED, keyboard, volume
and phones.Procedure:1. Press three buttons x , GAME EQ , and DISC 2 simulta-
neously.2. LEDs and fluorescent indicator tube are all turned on.3. Press simultaneously the two buttons of GAME EQ and DISC
2 . Whenever these two buttons are pressed simultaneously, themode changes from Key check, Key count check, Headphonesinput check and Volume check in this order.
4. When the Key check mode is entered, the display shows theindication of “KEY 0 0 0”.The keys that are assigned to the respective channels of the keyentry signal lines (KEY0, KEY1, KEY2) that are input to IC701Display Controller on the panel board, are checked. While youpress the button, the number that corresponds to the key shownin the table below, is displayed in the location of the correspond-ing channel. (The ?/1 and DISPLAY buttons are not includedin these channels.)
5. When the Key count check mode is entered, the display showsthe indication of “KEYCNT 0 0”.Whenever the button is pressed, number in the first digit incre-ments. (RV90D: 38) At the same time, only when the key isbeing pressed, the KEY channel is displayed in the second digit.(KEY0: 1, KEY1: 2, KEY2: 3)(The buttons that are already pressed once and the buttons of ?/1 and DISPLAY are not counted.)
6. When the Headphones input check mode is entered, the displayshows the indication of “H_P OFF” or “H_P ON” depending onthe PHONES jack status.
7. When the Volume check mode is entered, the display shows theindication of “VOLUME FLAT” or “VOLUME DOWN” or“VOLUME UP” depending on the VOLUME status.
8. You can exit the Test Mode when you press the GAME EQand DISC 2 buttons simultaneously.
DisplayLeft Center Right
(KEY0) (KEY1) (KEY2)
1 CD X DISC 1
2 TUNER/BAND x DISC 2
3 TAPE A/B ALBUM + DISC 3
4 VIDEO (MD) > Z OPEN/CLOSE
5 GAME M +DISC SKIP/
EX-CHANGE
6 KARAOKE PON g GTUNER MEMORY
PLAY MODE
7 SPECTRUM – mFM MODE
REPEAT
8 GAME EQ ALBUM –DIRECTION
EDIT
9 MUSIC EQ . CD SYNC
10 EFFECT ON/OFF bREC
PAUSE/START
11 GAME MIXING V P FILE
12 GROOVE B ENTER
13 PICTURE EFFECT v MOVIE EQ
14 — —SURROUND
SPEAKER MODE
4
HCD-RV2/RV5/RV6
[MC Test Mode]• This mode is used to check operations of the respective sections
of Amplifier, Tuner, and Tape.Procedure:• To enter MC Test Mode1. Press ?/1 button to turn on the set.2. Press the three buttons of x , GAME EQ and DISC 3 simul-
Output channel switching:MUSIC key: L , L R , R throughMOVIE key: L , SL R , SR throughGAME key:L , L, SL, C R , R, SR, SW through
1. When VOLUME control knob is turned clockwise even slightly,the sound volume increases to is maximum and a message “VOL-UME MAX” appears for two seconds, then the display returnsto the original display.
2. When VOLUME control knob is tuned counter-clockwiseeven slightly, the sound volume decreases to its minimum and amessage “VOLUME MIN” appears for two seconds, then thedisplay returns to the original display.
3. When you press the v button, the message “GEQ MAX” isdisplayed and the entire band of the graphic equalizer is set tothe maximum level.
4. When you press the V button, the message “GEQ MIN” isdisplayed and the entire band of the graphic equalizer is set tothe minimum level.
5. When you press the b , B or P FILE (HCD-RV5/RV6), EFFECT ON/OFF (HCD-RV2) button, the message “GEQ FLT”is displayed and the entire band of the graphic equalizer is set tothe center level.
6. Whenever you press the ENTER (HCD-RV5/RV6), GROOVE(HCD-RV2) button, it toggles between “VACS ON” and “VACOFF” so that you can switch ON or OFF of VACS.
* To return to normal mode again.1. When you want to exit this mode, press ?/1 button.2. The cold reset is enforced at the same time.
[Aging Mode]This mode can for operation check of tape deck section.• If an error occurred: The aging operation stops and display then status.• If no error occurs:The aging operation continues repeatedly.Procedure:1. Press the CD button to select the function “CD”.2. Load the tapes into the decks A and B respectively.3. Set a disk in “DISK1” tray.4. Press the PLAY MODE button to set the “ALL DISCS” mode,
and press the REPEAT button to “REPEAT” off.5. Press three buttons of x , GAME EQ , and DISC SKIP/EX-
CHANGE simultaneously.6. The florescent indicator tube display “AGING”, aging mode start.7. To exit from the aging mode, operate the cold reset.
• The sequence during the aging mode is following as below.• If an error occurred, stop display that step.
Aging mode sequence (Tape deck section):
Rewind the tape A“TAPE A AG-1”
Rewind the tape B“TAPE A AG-2”
FWD play the tape A“TAPE A AG-3”
Fast forward the tape A“TAPE A AG-4”
RVS play the tape A“TAPE A AG-5”
Rewind the tape A“TAPE A AG-6”
FWD play the tape B“TAPE B AG-3”
Fast forward the tape B“TAPE B AG-4”
RVS play the tape B“TAPE B AG-5”
Rewind the tape B“TAPE B AG-6”
Shut off
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
2 minutes
Shut off or 20 seconds
2 minutes
Shut off
5
HCD-RV2/RV5/RV6
[CD Service Mode]• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the optical pick-up.Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “CD”.3. Press three buttons x , MUSIC EQ , and DISC 3 simulta-
neously.4. The CD service mode is selected.5. With the CD in stop status, press M + button to move the
optical pick-up to outside track, or press – m button to insidetrack.
6. To release this mode, press the ?/1 button.
Error History Display1. CDM Error History <CDM58E Error History Display>11 digits are displayed after the M character.
Example of display : M0FF400220000
1st digit : Indicates the error history number.0 is the latest error
2nd to 3rd digits : Indicates the details of the problem.01 : Initialization table is currently rotating 102 : Initialization table is currently rotating 203 : Initialization table is currently rotating 304 : Currently DISC SKIP in OPEN mode05 : CLOSE table is currently rotating06 : Chucking table is currently rotating07 : Currently performing SHIP operations08 : Currently performing release operations09 : Currently performing POWER OFF
operations
4th to 5th digits : Processing when problems occur01 : Currently performing SHIP operations02 : Currently performing POWER OFF
operations03 : Currently initializing04 : Currently performing release operations05 : Currently in chuck stop state06 : Currently performing CLOSE operations07 : Currently performing exchange CLOSE
operations08 : Currently performing OPEN operations09 : Currently performing OPEN POP UP
operations0A : Currently performing exchange OPEN
operations6 to 7th digits : Operations currently performed for problems
which have occurred8th to 9th digits : Targets of processing when problems occur
Same as 4th to 5th digits10th to 11th digits : Fixed at 00
[CD Ship Mode (No Memory Clear)]• This mode moves the position to the position durable to vibra-
tion Use this mode when returning the set to the customer afterrepair.
Procedure:1. Press ?/1 button to turn the set ON.2. Press three CD button and ?/1 button simultaneously.3. After the “STANBY” display blinks six times, a message
“LOCK” is displayed on the fluorescent indicator rube, and theCD ship mode is set.
[CD Ship Mode (Memory Clear)]• This mode moves the pickup to the position durable to vibra-
tion. Use this mode when returning the set to the customer afterrepair.
Procedure:1. Press ?/1 button to turn the set ON.2. Press three buttons ENTER , DISC 1 , and CD button simul-
taneously.3. After the “STANDBY” display blinks six times, a message
“LOCK” is displayed on the fluorescent indicator tube, and theCD ship mode is set.
6
HCD-RV2/RV5/RV6
[REPEAT 5 LIMIT OFF MODE]• This mode is used to enable infinite repetitions.
Normally, the number of repetitions allowed is 5.Procedure:1. Press ?/1 button to turn ON the power supply.2. Set the function “DVD”.3. Press three burtons x , MUSIC EQ and DISC 2 is simulta-
neously.4. Infinite repetitions is enabled.5. This state is maintained ( memorized ) until COLD RESET is
executed.
2. MECHANICAL ADJUSTMENTSPrecaution1. Clean the following parts with a denatured alcohol-moistened
swab:record/playback heads pinch rollerserase head rubber beltscapstan idlers
2. Demagnetize the record/playback head with a head demagne-tizer.
3. Do not use a magnetized screwdriver for the adjustments.4. After the adjustments, apply suitable locking compound to the
parts adjusted.5. The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.
Torque Measurement
Mode Torque meter Meter reading3.06 N • m to 6.96 N • m
FWD CQ-102C 31 to 71 g • cm(0.43 – 0.98 oz • inch)
FWD0.19 N • m to 0.58 N • m
back tensionCQ-102C 2 to 6 g • cm
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • mREV CQ-102RC 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
REV0.19 N • m to 0.58 N • m
back tensionCQ-102RC 2 to 6 g • cm
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • mFF/REW CQ-201B 71 to 143 g • cm
(0.98 – 1.99 oz • inch)9.80 N • m
FWD tension CQ-403A 100 g or more(3.53 oz or more)
9.80 N • mREV tension CQ-403R 100 g or more
(3.53 oz or more)
7
HCD-RV2/RV5/RV6
3. ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB=0.775 V
1. Demagnetize the record/playback head with a headdemagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.3. After the adjustments, apply suitable locking compound to the
parts adjust.4. The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustmentshould be completed before performing recording circuit adjust-ment.)
6. The adjustments should be performed for both L-CH and R-CH.7. Switches and controls should be set as follows unless otherwise
specified.
• Test Tape
Record/Playback Head Azimuth Adjustment
DECK A DECK B
Note: Perform this adjustments for both decksProcedure:1. Mode: Playback
2. Turn the adjustment screw and check output peaks. If the peaksdo not match for L-CH and R-CH, turn the adjustment screw sothat outputs match within 1dB of peak.
3. Mode: Playback
4. After the adjustments, apply suitable locking compound to thepats adjusted.
Adjustment Location: Playback Head (Deck A).Record/Playback/Erase Head (Deck B).
set
main boardIC201Pin 5 (PB OUT(R))Pin wh (PB OUT(L))
main boardIC201Pin eh (GND)
+–
level meter
test tapeP-4-A100(10 kHz, –10 dB)
Screwposition
L-CHpeak
within1dB
Outputlevel
L-CHpeak
R-CHpeak
within1dB
Screwposition
R-CHpeak
MAINboardIC201 set
test tapeP-4-A100(10 kHz, –10 dB)
pin 5
oscilloscope
L-CH
R-CH
V H
waveform of oscilloscope
in phase 45° 90° 135°180°
good wrong
pin eh
pin wh
L
R
forward
reverse
Tape Signal Used forP-4-A100 10 kHz, –10 dB Azimuth Adjustment
WS-48B 3 kHz, 0 dB Tape Speed Adjustment
P-4-L300 315 Hz, 0 dB Level Adjustment
8
HCD-RV2/RV5/RV6
TUNER SECTION
FM Tuned Level Adjustment
Procedure:1. Supply a 25 dB 98 MHz signal from the ANTENNA terminal.2. Tune the set to 98 MHz.3. Adjust RV101 to the point (moment) when the TUNED indica-
tor will change from going off to going on.
Adjustment Location: MAIN board
Null Adjustment
Procedure:1. Supply a 60 dB 98 MHz signal from the ANTENNA terminal.2. Tune the set to 98 MHz.3. Measure voltage between pin 22 (AFC) and pin 3 (REG) of IC
Note:1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.2. Use LUV-P01 (Part No. 4-999-032-01) unless otherwise indi-
cated.3. Use an oscilloscope with more than 10MW impedance.4. Clean the object lens by an applicator with neutral detergent when
the signal level is low than specified value with the followingchecks.
S-CURVE CHECK
Procedure :1. Connect an oscilloscope to TP68 (FE) and TP73 (DVD) on the
BD board.2. Turn the power ON.3. Load a disc (LUV-P01) and actuate the focus search. (In conse-
quence of open and close the disc tray, actuate the focus search)4. Confirm that the oscilloscope waveform (S-curve) is symmetri-
cal between A and B. And confirm peak to peak level within 2 ±0.5 Vp-p.
Note: • Try to measure several times to make sure than the ratioof A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up thebrightness to obtain best waveform.
RF LEVEL CHECK
Procedure :1. Connect an oscilloscope CH1 to TP71 (RFDC), CH2 to TP72
(RFAC) and TP73 (DVD) on the BD board.2. Turn the power ON.3. Load a disc (LUV-P01) and playback the number nine track.4. Confirm that oscilloscope waveform is clear and check if RF
signal level is correct or not.
Note: Clear RF signal waveform means that the shape “ ◊ ” can beclearly distinguished at the center of the waveform.
TRAVERSE LEVEL CHECK
Procedure :1. Connect an oscilloscope to TP70 (TE) and TP73 (DVD) on the
BD board.2. Turn the power ON.3. Load a disc (LUV-P01) and playback the number nine track.4. Press the hH button. (Becomes the 1 track jump mode.)5. Confirm that the level B and A (DC voltage) on the oscilloscope
waveform.
Connecting Location:
+–
oscilloscope
BD board
TP68 (FE)TP73 (DVD)
symmetry
S-curve waveform
within 2 ±0.5Vp-p
A
B
+–
oscilloscope
TP71 (RFDC)TP72 (RFAC)
BD board
TP73 (DVD)
RF signal waveform
VOLT/DIV : 200mVTIME/DIV : 500ns
level : 0.75 ±0.1Vp-p (RFDC)1.05 ±0.3Vp-p (RFAC)
TP70 (TE)TP73 (DVD)
BD board
+–
oscilloscope
level=1.2 ±0.55Vp-p symmetry
A (DC voltage)
center ofwaveform
B
DVC
1 track jump waveform
– BD BOARD (Conductor Side) –
TP70(TE)
TP68(FE)
TP71(RFDC)
TP73(DVD)
TP72(RFAC)
10
HCD-RV2/RV5/RV6
VIDEO SECTION
VIDEO LEVEL ADJUSTMENT(AUDIO LEVEL/VIDEO CLOCK/AUDIO SERVOCLOCK CHECK)
Procedure :1. Connect an oscilloscope to TP308 (V-OUT) on the VIDEO board.2. Connect a level meter to TP415 (L-OUT) and TP413 (R-OUT)
on the VIDEO board.3. Connect a frequency counter to TP70 (54 MHz) and TP182
(4.2336 MHz) on the VIDEO board.3. Turn the power ON.4. Set a test disc (HLV-402 (Part No. 8-909-870-00))5. Press three buttons x , MUSIC EQ , and DISC 3 simulta-
neously.6. The message “MPEG AV TEST” is displayed on the fluorescent
indicator tube. Color bar signal outputs and sine-wave (1 kHz0 dB) appears.
7. Adjust the RV501 on the VIDEO board for 0.714 ± 0.05 Vp-p.Note: TP308 (V-OUT) on the VIDEO board must be teminated by
75 Ω.
8. Confirm that the value of level meter is 2.5 ± 2.0 dBs. (If audiooutput disappear, press the PLAY MODE button twice)
9. Confirm that the value of frequency counter is 54 MHz ± 400Hz.
10.Confirm that the value of frequency counter is 4,2336 MHz.11.Change disc to a MP3 test disc (MP3 1kHz 0dB sine-wave is
recorded)12.Confirm that the value of level meter is 2.4 ± 2.0 dBs.
Connecting and Adjustment Location:
VIDEO board
TP308 (V-OUT) +–
oscilloscope
+–
level meterVIDEO board
TP415 (L-OUT)TP413 (R-OUT)
VIDEO board
TP70 (54 MHz)TP182 (4.2336 MHz)
+–
frequency counter
– VIDEO BOARD (Component Side) –
TP308(V-OUT)
TP70(54 MHz)
TP182(4.2336 MHz)
TP415(L-OUT)
TP413(R-OUT)
RV501VideoLevel
Adjustment
11
HCD-RV2/RV5/RV6
4. IC PIN FUNCTION DESCRIPTION• IC601 M30620MCN-A02FP (SYSTEM CONTROL) (MAIN BOARD)
Pin No. Pin Name I/O Pin Description
1 S OUT O Serial data signal output to display control (IC701)
2 S CLK O Serial clock signal output to display control (IC701)
3 POWER ON O Power standby LED on/off signal output ON: “L”, OFF: “H”
4 SIRCS IN I Sircs signal input from remote control receiver (RM701)
5 M61519FP DATA O Serial data signal output to M61519FPD61G (IC301)
6 CD MUTE O CD mute signal output ON: “L”, OFF: “H”
7 M61519FP CLK O Serial clock signal output to M61519FPD61G (IC301)
8 BYTE I Not used in this set. (Connect to GND.) EXT BUS INPUT with selector input
9 CNVSS — Ground pin
10 XCIN I Sub clock signal input (32.768 kHz)
11 XCOUT O Sub clock signal output (32.768 kHz)
12 RESET I System reset signal input from reset IC (IC661)
13 XOUT O System clock signal output (16 MHz)
14 VSS — Ground pin
15 XIN I System clock signal input (16 MHz)
16 VCC — Power supply pin (+3.3 V)
17 NMI I Pull up pin (EVER+3.3 V)
18 AC CUT I AC cut signal input ON: “L”, OFF: “H”
19 SYS CS I VMP CS input from CXD1887R (IC505)
20 RDS INT I Not used in this set. (Connect to GND.) RDS INTEGER signal input
21 RDS DATA O Not used in this set. (Connect to GND.) RDS DATA signal output
22 ST MUTE O Stereo mute signal output
23 STEREO IN I Stereo signal input from FM/AM IF MIX (IC101) ON: “L”, OFF: “H”
24 TUNER I Tuned signal input from FM/AM IF MIX (IC101) ON: “L”, OFF: “H”
25 ST CE O Stereo chip enable signal output to PLL IC (IC102)
26 ST DOUT O Stereo data signal output to PLL IC (IC102)
27 ST DIN I Stereo data signal input from PLL IC (IC102)
28 ST CLK O Stereo clock signal output to PLL IC (IC102)
29 IIC CLK I/O Not used in this set. (Fixed at “H” in this set.) II2 SDA pull up pin
30 IIC DAT I/O Not used in this set. (Fixed at “H” in this set.) II2 SCL pull up pin
31 – 34 NC O Not used in this set. (Open)
35 SYS OUT O VMP data signal output to CXD1887R (IC505)
36 SYS IN I VMP data signal input from CXD1887R (IC505)
37 SYS CLK I VMP clock signal input from CXD1887R (IC505)
38 SYS RQ O VMP request signal output to CXD1887R (IC505)
39 SYS OK O VMP OK signal output to CXD1887R (IC505)
40 SYS POWER O VMP/MB power on/off signal output ON: “H”, OFF: “L”
41 SYS RESET O VMP/MB reset signal output
42 M RESET O Reset signal output
43 NC O Not used. (Open)
44 LOAD IN O Loading in signal output ON: “H”, OFF: “L”
45 LOAD OUT O Loading out signal output ON: “H”, OFF: “L”
46 OPEN I Open switch signal input from S701
47 CLOSE I Close switch signal input from S701
48 UP/DOWN I Up/down switch signal input from S711
49 T SENS I Table sensor signal input from address sensor IC (IC711)
50 NC I Not used. (Fixed at “L” in this set.)
51 NC O Not used. (Fixed at “L” in this set.)
52, 53 NC O Not used. (Open)
54 VIDEO MUTE O Video mute signal output ON: “H” (VCD)/“L” (DVD), OFF: “L” (VCD)/“H” (DVD)
55 VIDEO SW O Video switch signal output “L”: VCD/DVD, “H”: other
12
HCD-RV2/RV5/RV6
Pin No. Pin Name I/O Pin Description
56 REAR LINK O Rear link signal output (HCD-RV6 only) ON: “H”, OFF: “L”
57 SUR1 O Surround control signal output to LA2615 (IC304)
58 SUR2 O Surround control signal output to LA2615 (IC304)
59 SUR3 O Surround control signal output to LA2615 (IC304)
60 A TRG O A trigger signal output ON: “H”, OFF: “L”
61 B TRG O B trigger signal output ON: “H”, OFF: “L”
62 VCC — Power supply pin (+3.3 V)
63 NC O Not used. (Open)
64 VSS — Ground pin
65 CAPM CONT O Capstan motor control signal output ON: “H”, OFF: “L”
66 B REC FWD I TCM-B FWD recording switch signal input “L”: active
67 B REC REW I TCM-B REV recording switch signal input “L”: active (HCD-RV5/RV6 only)
68 A HAFE I TCM-A half signal input “L”: active
69 B HAFE I TCM-B half signal input “L”: active
70 A PLAY I TCM-A playing switch signal input “L”: active
71 B PLAY I TCM-B playing switch signal input “L”: active
72 AMS IN I AMS signal input No music: “L”, music: “H”
73 DISPLAY KEY I Display key (S742) signal input “L”: active
74 POWER KEY I Power key (S716) signal input “L”: active
75 BIAS O Bias on/off signal output ON: “H”, OFF: “L”
76 PB A/B O Playback A/B select signal output to HA12237F (IC201) “H”: A, “L”: B
77 TC RELAY O TC relay signal output REC: “L”, Other: “H”
78 PB MUT O Playback mute signal to HA12237F (IC201) ON: “L”, OFF: “H”
79 REC MUT O Recording mute signal to HA12237F (IC201) ON: “L”, OFF: “H”
80 A SHUT IN I Reel pulse signal input
81 B SHUT IN I Reel pulse signal input
82 LINEOUT MUT O Line (MD/VIDEO) mute signal output ON: “L”, OFF: “H”
83 LINE MUT O TA line mute signal output ON: “L”, OFF: “H”
84 STK MUT O STK mute signal output ON: “L”, OFF: “H”
85 PROTECT I Protect signal input ON: “L”, OFF: “H”
86 STB RELAY O Standby relay signal output ON: “H”, OFF: “L”
87 NC O Not used. (Open)
88 FRONT RELAY O Front speaker relay signal output ON: “H”, OFF: “L”
89 SP1/METER-L I HCD-RV2: Meter L signal input HCD-RV5/RV6: Spectrum analyzer signal input
90 SP2/METER-R I HCD-RV2: Meter L signal input HCD-RV5/RV6: Spectrum analyzer signal input
91 SP3 I HCD-RV2: Fixed at “L”. HCD-RV5/RV6: Spectrum analyzer signal input
92 SP4 I HCD-RV2: Fixed at “L”. HCD-RV5/RV6: Spectrum analyzer signal input
93 MODE IN I Model select input
94 SPEC IN I Spec select input
95 VACS IN I VACS signal input
96 AVSS — Ground pin
97 NC I Not used. (Open)
98 V REF — AV reference pin
99 AVCC — Power supply pin (+3.3 V)
100 S IN I Serial data signal input to display control (IC701)
IC102FOCUS/TRACKING COIL DRIVE,SLED/SPINDLE MOTOR DRIVE
LPFCD-L
X50133.8888MHz
X50228MHz
RV501
M102(SLED)
M101(SPINDLE)
OPTICAL PICKUPBLOCK
F MAIN SECTION(RV5)
B MAIN SECTION(RV2)
•Signal Path
•R-ch is omitted due to same as L-ch.
: CD
:VIDEO
E MAIN SECTION(RV5)
H MAIN SECTION(RV6)
I MAIN SECTION(RV6)
C MAIN SECTION(RV2)
VIDEO LEVEL
(Page 17)
(Page 17)
(Page 18)
(Page 19)
(Page 18)
(Page 19)
1616
HCD-RV2/RV5/RV6
6. BLOCK DIAGRAM — TUNER, POWER SECTION —
1016201918
79112
1
22
15
IC901
EVER+4V
UNREG+12V
3 1+12VREG
IC683
+12V
3 1+9.2VREG
IC684
RY901
D911
JW911
F919 +9V+7V
VF1
VF2
+B
-B
3 1+4.9VREG
IC685
+5V
3 1+5VREG
IC681
D686
D667
D668
D663
D664
IC601 (2/3)SYSTEM CONTROL
A+5V
+4V
FAN+B +3.3V1
+3.3V2
+3.3V3
A+2.5V
A+3.3V1
A+3.3V2
A+4.5V
1 3+2.5VREG
IC201
1 3+3.3VREG
IC202
3 1+4VREG
IC682
1 3 12
18
RESET
IC661
VP-30VREGQ911
RELAYDRIVEQ901
POWERSWITCH
Q681,682
BUFQ661
MUTEQ103
FM IFBUFQ101
+BSW
Q101R-CH
L-CH
+12V
FM
CF102
IC101AM/FM IF MIX
CF101
FM+B
FM/AM
ST-MUTE XC OUT
TUNERSTEREO
ST-DINDODICLCE
ST-DOUTST-CLKST-CE
AC OUT
RESET
XC IN
X OUT
X IN
STB RELAYSYS POWER
FMOSC VCO
A OUT IFA INPD
IF REQAM OSC
X IN DO
+12V
DICKCE
DODI
CEX OUT CLK
X1014.5MHz
X60132.768KHz
X60218MHz
2
1 6
5
JW1
JW4
JW6
S901
120V 220V 240V
VOLTAGE SELECTOR
JW3
RB101 10
11
12
AC IN
FM75Ω
G
AM
8 134
IF OUTF OUT
VT
ANT IN
6453
8
111210
21
23
22
1
2322
24
2627
2825
11
10
13
8640
15
1 3+4VREG
13
14
2
4
76
AM/FM
FM IF L OUT
R OUT
AM MIXOUT
AM IF IN
ST LEDTU LED
AM RF IN
AM OSC
AFC
VCO STOP
OSC/FM SD
IF REQ/MUTE
24 IFT101
IC102PLL
D108
RV101
T901SUB TRANS
T911POWER TRANSFOMER D542
D681-684
D687-690
D543
POWERAMP
SW901,JW911,F919:E3,EA,JE,MY,SP ONLYJW1,JW3,JW6:TH ONLY
D902-905
+3.3VREGQ581
+4.5VREGQ201
JK101ANTENNA
FM TUNERFE101
A MAIN SECTIO(RV2)
•Signal Path
•R-ch is omitted due to same as L-ch.
: FM
G MAIN SECTION(RV6)
D MAIN SECTION(RV5)
(RV2) (RV5) (RV6)
(Page 17)
(Page 18)
(Page 19)
17 17
HCD-RV2/RV5/RV6
7. BLOCK DIAGRAM — MAIN SECTION (HCD-RV2) —
REMOTECONTROLRECEIVER
55
75
39
25
1
40
2
36
2122
3835
1
6
712
84
83
100
1242
876
797876
74
73
4 1
6870
697166
8081
60
61
65
3
72
151413
28
23
24
26
21
34
32
1
2
7
3
17
1314
60
27I
32
69I
80
44I
58•
61I
67
9
4
3
20
MUTECONTQ362
A TRIGDRIVE
Q601,602B TRIGDRIVE
Q603,604 CAP MOTORDRIVE
Q605,606
FUNCTIONKEY
21FUNCTION
KEY
VOLUMEENCODER
22FUNCTION
KEY
LEDDRIVE
Q702-707
85
PROTECTDETECT
Q381,382
MUTEQ301
STK MUTEQ503,504
PROTECTDETECT
Q383
RELAYDRIVE
Q384,385
OVER LOADDETECTOR
Q501
MUTECONTQ365
1 MUTEQ363
FLOURESCENTINDICATOR TUBE
LEDDRIVEQ701
AMSQ261,262,264
RM701
LED701
JK701PHONESJK702
MIC LEVEL
MIC
SPEAKER
VOLUMEVR701
L
R
X1
A IN(L)
VIDEOCONT
B IN(L)
REC OUT(L)
PB OUT(L)
REC IN(L)
ALC(L)
EQ OUT(L)
REC MUTEPB MUTE
A/B
VIDEO SW
CLKDATA
AMS-IN
REC MUTEPB MUTEPB-A/B
A-HAFEA-PLAYB-REC
B-HAFE
STK MUTE
LINE MUTE
PROTECT
S-IN
S-INS-OUT
M-RESET
POWER-KEY
DISPLAYKEY
SIRCSIN
B-PLAYB-REC FWD
A-SHUT-INB-SHUT-IN
A-TRG
B-TRG
CAPM-CONT
POWERLED
X1
KEY0
KEY1
VP
KEY2
S-OUT
S-INS-CLKRESET
HEADPHONE
VOL-AVOL-B
VLOAD
LED
G0I
G11
S0I
S21
S723-732
S708-712S736-741
S701-704S717,718
RES7015MHz
IC701DISPLAY CONTROL
IC601 (3/3)SYSTEM CONTROL
IC301INPUT SELECT,TONE,VOLUME
IC201REC/PB AMP
LED702-707
DBFBQ421
Q387
IC602
RY371
Q386
Q581
-B
INB2
INA2
INEX2
DATACLOCK
INC2RECB2
MIC
REF
OUT2
D421
L-CH
CD-L
JK704
R-CH
L
RAUDIO
VIDEO
GAMEINPUT
VIDEO OUT
2 9ECHOAMP
IC703
1046
1319
BUF3VTO5V
VR703
ECHO LEVELVR702
IC702
IC704
JK602
REC/PBSW
Q255,256
BIAS SWQ258 75 BIAS
77 TC-RELAY
CAP M+9V
SOL B
SOL A
B PHOTOA PHOTO
A-MODEA-HAFE
REC(FWD)B-MODEB-HAFE
TAPE DECKQ251,253
Q257
+12V
BIASOSCQ250
R-CH
R-CH
B-DECK
RECORD/PLAYBACK/
ERASEHEAD
R-CH
A-DECK
PLAYBACKHEAD
L250BIAS COIL
CVOUT
13
IC501 (1/2)L-CH AMP
R-CH
VF2 VF1
FLD701
JK302
S716
S742
ATUNER/POWERSECTION
BCD/VIDEOSECTION
C CD/VIDEOSECTION
89 METER-L
L-CHBUF
Q369LEVELDET
Q307,308
(Page 16)
(Page 15)
(Page 15)
1818
HCD-RV2/RV5/RV6
REMOTECONTROLRECEIVER
JK301
L
R
8255
75
89
39
251
40
37
2
36
2122
3835
29
19
1
28
9 8
6
712
1 2 3
90
91
92
84
83
100
1242
876
575859
797876
74
73
4 1
687067
697166
8081
60
61
65
3
72
151413
28
23
24
26
21
34
32
1
2
7
3
17
1314
60
26I
32
68I
80
38I
58•
61I
67
9
4
3
20
MUTECONTQ362
A TRIGDRIVE
Q601,602B TRIGDRIVE
Q603,604 CAP MOTORDRIVE
Q605,606
FUNCTIONKEY
21FUNCTION
KEY
VOLUMEENCODER
22FUNCTION
KEY
LEDDRIVE
Q702-708
HIGHFREQ
D375,376
85
MID/HIGHFREQ
D377,378
MIDFREQ
D379,380
LOWFREQ
D381,382
PROTECTDETECT
Q381,382
MUTEQ301
STK MUTEQ503,504
PROTECTDETECT
Q383
RELAYDRIVE
Q384,385
OVER LOADDETECTOR
Q501
OVER HEATDETECT
Q582,583
MUTECONTQ365
1 MUTEQ363
FLOURESCENTINDICATOR TUBE
LEDDRIVEQ701
AMSQ261,262,264
RM701
LED701
JK701PHONES
JK702MIC LEVEL
MIC
IN
SPEAKER
VOLUMEVR701
L
R
FANDRIVEQ371
X1
LINE MUT
A IN(L)
VIDEOCONT
B IN(L)
REC OUT(L)
PB OUT(L)
REC IN(L)
ALC(L)
EQ OUT(L)
REC MUTEPB MUTE
A/B
VIDEO SW
CLKDATA
SUR1SUR2
SUR3
AMS-IN
REC MUTEPB MUTEPB-A/B
A-HAFEA-PLAYB-REC
B-HAFE
SP1
SP2
SP3
SP4
STK MUTE
LINE MUTE
PROTECT
S-IN
S-INS-OUT
M-RESET
POWER-KEY
DISPLAYKEY
SIRCSIN
B-PLAYB-REC FWD
A-SHUT-INB-SHUT-IN
A-TRG
B-TRG
CAPM-CONT
POWERLED
X1
KEY0
KEY1
VP
KEY2
S-OUT
S-INS-CLKRESET
HEADPHONE
VOL-AVOL-B
VLOAD
LED
G0I
G12
S0I
S29
S723-735
S708-715S736-740
S701-707S717-712
RES7015MHz
IC701DISPLAY CONTROL
IC601 (3/3)SYSTEM CONTROL
IC301INPUT SELECT,TONE,VOLUME
LED702-708
DBFBQ421
ANALOGSURROUND
IC304
TH501 Q584
Q387
IC602
RY371
Q386
Q581
-B
IC302 (1/2)
INB2
INA2
IND2
INEX2
DATACLOCK
INC2RECB2
MIC
REF
OUT2
SAOUT
TOUT2
VOLIN2
D421L-CH
CD-L
ON/O
FFCO
NT2
CONT
3
L
ROUT
JK704
R-CH
R-CH
R-CH
L
RAUDIO
VIDEO
GAMEINPUT
VIDEO OUT
MUTEQ367
L-CHBUF
Q369
2 9ECHOAMP
IC703
1046
1319
BUF3VTO5V
VR703
ECHO LEVELVR702
MD (VIDEO)
IC702
IC704
JK602
REC/PBSW
Q255,256
BIAS SWQ258 75 BIAS
77 TC-RELAY
CAP M+9V
SOL B
SOL A
B PHOTOA PHOTO
REC(REW)A-MODEA-HAFE
REC(FWD)B-MODEB-HAFE
TAPE DECKQ251,253
Q257
+12V
BIASOSCQ250
R-CH
R-CH
B-DECK
RECORD/PLAYBACK
HEAD
R-CH
A-DECK
PLAYBACKHEAD
L250BIAS COIL
CVOUT
Q304
13
IC501 (1/2)L-CH AMP
R-CH
VF2 VF1
FLD701
FAN961
JK302
S716
S742
12
ON/OFFCONT2CONT3
DTUNER/POWERSECTION
ECD/VIDEOSECTION
F CD/VIDEOSECTION
IC201REC/PB AMP
8. BLOCK DIAGRAM — MAIN SECTION (HCD-RV5) —
(Page 16)
(Page 15)
(Page 15)
19 19
HCD-RV2/RV5/RV6
REMOTECONTROLRECEIVER
JK301
L
R
8255
75
89
39
251
40
37
2
36
2122
3835
29
19
1
28
9 8
4
58
1 2 3
90
91
92
84
83
100
12
42
876
575859
797876
74
73
4 1
687067
697166
8081
60
61
65
3
72
151413
28
23
24
26
21
34
32
1
2
7
3
17
1314
60
26I
32
68I
80
38I
58•
61I
67
9
4
3
20
MUTECONTQ362
A TRIGDRIVE
Q601,602B TRIGDRIVE
Q603,604 CAP MOTORDRIVE
Q605,606
FUNCTIONKEY
21FUNCTION
KEY
VOLUMEENCODER
22FUNCTION
KEY
LEDDRIVE
Q702-708
HIGHFREQ
D375,376
85
MID/HIGHFREQ
D377,378
MIDFREQ
D379,380
LOWFREQ
D381,382
PROTECTDETECT
Q381,382
MUTEQ301
STK MUTEQ503,504
PROTECTDETECT
Q383
RELAYDRIVE
Q384,385
OVER LOADDETECTOR
Q501
OVER HEATDETECT
Q582,583
MUTECONTQ365
10 MUTEQ363
FLOURESCENTINDICATOR TUBE
LEDDRIVEQ701
AMSQ261,262,264
RM701
LED701
JK701PHONES
JK702
MIC LEVEL
MIC
IN
SPEAKER
VOLUMEVR701
L
R
FANDRIVEQ371
X1
LINE MUT
A IN(L)
VIDEOCONT
B IN(L)
REC OUT(L)
PB OUT(L)
REC IN(L)
ALC(L)
EQ OUT(L)
REC MUTEPB MUTE
A/B
VIDEO SW
CLKDATA
SUR1SUR2
SUR3
AMS-IN
REC MUTEPB MUTEPB-A/B
A-HAFEA-PLAYB-REC
B-HAFE
SP1
SP2
SP3
SP4
STK MUTE
LINE MUTE
PROTECT
56REAR LINK
S-IN
S-INS-OUT
M-RESET
POWER-KEY
DISPLAYKEY
SIRCSIN
B-PLAYB-REC FWD
A-SHUT-INB-SHUT-IN
A-TRG
B-TRG
CAPM-CONT
POWERLED
X1
KEY0
KEY1
VP
KEY2
S-OUT
S-INS-CLKRESET
HEADPHONE
VOL-AVOL-B
VLOAD
LED
G0I
G12
S0I
S29
S723-735
S708-715S736-741
S701-707S717-712
RES7015MHz
IC701DISPLAY CONTROL
IC601 (3/3)SYSTEM CONTROL
IC301INPUT SELECT,TONE,VOLUME
LED702-708
DBFBQ421
ANALOGSURROUND
IC304
TH501 Q584
Q387
IC602
RY371
Q386
Q581
-B
IC302 (1/2)
INB2
INA2
IND2
INEX2
DATACLOCK
INC2RECB2
MIC
REF
OUT2
SAOUT
TOUT2
VOLIN2
D421L-CH
CD-L
ON/O
FFCO
NT2
CONT
3
L
ROUT
JK704
R-CH
R-CH
R-CH
L
RAUDIO
VIDEO
GAMEINPUT
VIDEO OUT
MUTEQ367
L-CHBUF
Q369
2 9ECHOAMP
IC703
1046
1319
BUF3VTO5V
VR703
ECHO LEVELVR702
MD (VIDEO)
IC702
IC704
JK602
REC/PBSW
Q255,256
BIAS SWQ258 75 BIAS
77 TC-RELAY
CAP M+9V
SOL B
SOL A
B PHOTOA PHOTO
REC(REW)A-MODEA-HAFE
REC(FWD)B-MODEB-HAFE
TAPE DECKQ251,253
Q257
+12V
BIASOSCQ250
R-CH
R-CH
B-DECK
RECORD/PLAYBACK
HEAD
R-CH
A-DECK
PLAYBACKHEAD
L250BIAS COIL
CVOUT
Q304
13
IC501 (1/2)L-CH AMP
R-CH
VF2 VF1
FLD701
FAN961
JK302
S716
S742
12
ON/OFFCONT2CONT3
SURROUNDSPEAKER
L
R
RY372
R-CH
JK303
GTUNER/POWERSECTION
HCD/VIDEOSECTION
I CD/VIDEOSECTION
RELAYDRIVEQ388
IC201REC/PB AMP
9. BLOCK DIAGRAM — MAIN SECTION (HCD-RV6) —
(Page 16)
(Page 15)
(Page 15)
2020
HCD-RV2/RV5/RV6
MEMO
21
HCD-RV2/RV5/RV6
MEMO
22
HCD-RV2/RV5/RV6
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision1.0 2002. 07 New
1.1 2002. 10Addition of Test Mode, Mechanical Adjustments, Electrical Adjustments,IC Pin Function Description and Block Diagrams.
1.2 2002. 11 Addition of Part No. for SUPPLEMENT-1 (9-874-131-81).