RUBBER HOSES · 2018. 12. 10. · U8000-08 21.68 NOTE: When using the “U” series ferrule with an ‘X’ series insert crimp to the above specified diameter +/- 0.13MM IMPORTANT:

federalhose.com/europower | 800-346-4673

RUBBER HOSES

R1 (MEETS / EXCEEDS THE REQUIREMENTS OF EN 853, ISO 1436 & SAE 100R1AT)

CONSTRUCTION TUBE Oil resistant synthetic rubber

REINFORCEMENT One high tensile steel wire braid

COVER Abrasion, ozone and weather resistant synthetic rubber

MSHA approved cover available on request

APPLICATIONS Medium pressure hydraulic oil lines Water and water-based fluid lines

TEMPERATURE RANGE -40ºC to +100ºC. Water & water-based fluids +70ºC max

HOSE TYPE NORMAL INSIDE DIAMETER

WORKING PRESSURE BEND RADIUS

PSI BAR INCHES MILLIMETERS

R1-04 1/4” 3,260 225 3.9 100

R1-06 3/8” 2,610 180 5.1 130

R1-08 1/2” 2,320 160 7.1 180

R1-10 5/8” 1,885 130 7.9 200

R1-12 3/4” 1,520 105 9.4 240

R1-16 1” 1,275 88 11.8 300

R1-20 1-1/4” 915 63 16.5 420


RUBBER HOSES

R2 (MEETS / EXCEEDS THE REQUIREMENTS OF EN 853, ISO 1436 & SAE 100R2AT)


REINFORCEMENT Two high tensile steel wire braids


MSHA approved cover available on request

APPLICATIONS High pressure hydraulic oil lines Water and water-based fluid lines





R2-04 1/4” 5,800 400 3.9 100

R2-06 3/8” 4,785 330 5.1 130

R2-08 1/2” 3,990 275 7.1 180

R2-10 5/8” 3,625 250 7.9 200

R2-12 3/4” 3,120 215 9.4 240

R2-16 1” 2,390 165 11.8 300


RUBBER HOSES

R16 (MEETS / EXCEEDS THE REQUIREMENTS OF SAE 100R16 & ISO 11237 R16)


REINFORCEMENT Two high tensile steel wire braids


MSHA approved cover as standard

APPLICATIONS High pressure hydraulic oil lines where a tight bend radius is required. Water and water-based fluid lines





R16-04 1/4” 5,000 345 2.0 50

R16-06 3/8” 4,000 276 2.6 65

R16-08 1/2” 3,500 241 3.5 90

R16-12 3/4” 2,250 155 4.7 120

R16-16 1” 2,000 138 5.9 150


RUBBER HOSES

R17 (MEETS / EXCEEDS THE REQUIREMENTS OF SAE 100R17 & ISO 11237 R17)


REINFORCEMENT 1/4”-1/2” One high tensile steel wire braid 5/8”-1” Two high tensile steel wire braids


MSHA approved cover as standard

APPLICATIONS Hydraulic systems which operate at or below 210 bar and require a tight bend radius Water and water-based fluid lines





R17-04 1/4” 3,000 210 2.0 50

R17-06 3/8” 3,000 210 2.6 65

R17-08 1/2” 3,000 210 3.5 90

R17-10 5/8” 3,000 210 3.9 100

R17-12 3/4” 3,000 210 4.7 120


RUBBER HOSES

CRIMPING DATA 1 PIECE FITTINGS

FITTING CODE HOSE TYPE

06 10 12 16 20 25 32

1/4" 3/8" 1/2" 5/8" 3/4" 1" 1.1/4”

04 06 08 10 12 16 20

‘A’ SERIES

SAE 100 R1AT (EN 853 1SN)

0.684 (17.37)

0.865 (21.97)

0.952 (24.18)

1.169 (29.69)

1.343 (34.11)

1.666 (42.32)

1.923 (48.84)

SAE 100 R2AT (EN 853 2SN)

0.733 (18.62)

0.888 (22.56)

0.990 (25.15)

1.184 (30.07)

1.337 (33.96)

1.659 (42.14)

2.017 (51.23)

SAE 100R16

0.695 (17.65)

0.851 (21.62)

0.959 (24.36)

1.184 (30.07)

1.293 (32.84)

1.605 (40.77) —

SAE 100R17

0.662 (16.81)

0.839 (21.31)

0.965 (24.51)

1.207 (30.66)

1.291 (32.79)

1.609 (40.87) —

The above crimping diameters are in inches and should be crimped to the specified diameter +/- 0.005”

(Crimping diameters in brackets are in meric and should be crimped to the specified diameter +/- 0.13MM) Cut hose end square, lightly lubricate the hose bore with a compatible fluid, push the coupling fully on the hose, place the assembly in to the crimping machine die

set by 1.0 to 1.5mm (0.040-0.060”)

NOTE: Crimping machines with the floating head double taper die set are not suitable for crimping these couplings.


THERMOPLASTIC HOSES

R7 HIGH SPECIFICATION SAE 100R7

CONSTRUCTION 720 consists of a nylon 12 tube reinforced with one braid of polyester fibre with a pin-pricked black polyurethane cover.

APPLICATIONS Solvent lines, refrigeration systems and gas lines.





R7-04 1/4” 2,750 190 2.7 69

R7-06 3/8” 2,250 155 4.5 114

R7-08 1/2” 2,000 140 6.0 152

R8 SAE 100R8 (TO SAE 100R7 DIMENSIONS)

CONSTRUCTION 737 consists of a polyester elastomer tube reinforced with one braid of polyaramid fibre and a black polyurethane cover.

(This hose is available as a non-conductive version - hose type 837 which has a non pin-pricked orange cover)

APPLICATIONS General hydraulics, mechanical handling, construction equipment, machine tools and pressure jetting.





R8-04 1/4” 5,000 345 2.0 51

R8-06 3/8” 4,000 275 2.5 64

R8-08 1/2” 3,500 240 3.2 82


THERMOPLASTIC HOSES

CRIMPING DATA 2 PIECE FITTINGS

HOSE TYPE INSERT TYPE COLLAPSE MANDREL

TOLERANCE ON SWAGING

04 06 08

1/4" 3/8” 1/2"

06 10 12

720

U SERIES INSERT

U MANDREL HPT-16888-**U

TO COLLAPSE MANDREL HPT-16888-**U

U7000-04 14.37

U7000-06 18.40

U8000-08 22.32

373

TO COLLAPSE MANDREL HPT-16888-**U

U7000-04 14.19

U7000-06 18.28

U8000-08 21.68

NOTE: When using the “U” series ferrule with an ‘X’ series insert crimp to the above specified diameter +/- 0.13MM

IMPORTANT: 1. Do not use lubrication of any kind when assembling ET series inserts

2. If the above crimp diameters do not produce an insert bore collapse then they must be adjusted to do so. The collapse mandrel part numbers are as above

where ** denotes the insert tail size.


FITTINGS

DM&Q PROGRAM Accepted industry standards are fine, as far as they go, but remember that standards such as DIN and SAE apply to the hose only, and not to the end connection or its integrity with the hose. Mixing untested hose and fittings from a variety of sources with assembly techniques based on trial and error, rather than properly structured development work and hours of impulse testing is, regrettably, an all too common occurrence – as common as hydraulic hose assembly failure, in fact.

Yet with your hydraulic life-blood at risk, it is vital that the whole assembly has complete integrity, is guaranteed to work and proven to be completely reliable.

The DM&Q emblem provides just this assurance and guarantees that a hose assembly has been Designed, Matched and Qualified for total integrity and maximum performance.

Components are Designed – using the most advanced computer technology – to complement each type and dimension of hose perfectly, and Matched by highly trained and specially qualified technicians to provide perfect couplings every time. Finally, the complete assembly is Qualified using the most rigorous testing procedures at our own test house, to guarantee that it will measure up to the most exacting performance demands.

Instead of the risks of “mix-and-match” hose components, look for the DM&Q emblem. It is exclusive to Europower hose assemblies and is your guarantee of performance assurance.

DMQ is a Europower Hydraulics Registered Trademark.

INTEGRATED SUPPLIER PROGRAM Our DM&Q program has shown that not all hydraulic hose assemblies are created equal – but even that is not the whole story.

By effectively becoming part of a customer’s design team, Europower can not only ensure the integrity of the individual components, but also advise on the system layout.

This is called the Integrated Supplier Program and it plays a vital part in the quality equation.

Unsuitable installation, for example, can threaten the efficiency of an otherwise adequate system. Inconsistent flow conditions, twists in the hose, tight bends and poor hose assembly routing can cause premature failure.

The design and installation of hose assemblies into complex machinery is inevitably one of the last tasks to be undertaken and quality is often compromised by the immense pressures to met very tight prototype and production deadlines.

That is why Europower’s Integrated Supplier Program includes a closely-knit team of qualified engineers covering sales, design, cost and quotations and methods engineering. They will not disappear the moment the order pad is signed. You can rely on their expertise to nurse the job through internal systems until production deliveries are running regularly and consistently. It is this nursery approach that enables the smooth transition from prototype to production.

Therefore, what the Integrated Supplier Program offers is the most cost effective solution to the problem. What’s more, the cost is, for the first time, a single, known and quantifiable cost because the unpredictable cost of failure – of downtime and warranty claims – is effectively removed from the equation.

Integrated Supplier Program is a Europower Hydraulics Registered Trademark.


FITTINGS

THE ABC’S OF ORDERING EUROPOWER INC. ONE PIECE HOSE ENDS

• To order the standard 2-piece Hose End use the ‘U’ part number provided. i.e. U02BM03

• To order two piece Thermoplastic end, substitute a ‘U’ for the ‘A’ i.e. U02BM03 --- A02BM03 o Can be used on the following hoses:

o CITISN – SAE 100R16 – SAE100R12 – Europulse 2 – C2T2SN – SAE 100R17 – 4SP

• To order the one-piece Thermoplastic Hose End that uses U700 Ferrules substitute a ‘B’ for the ‘U’ i.e. U02BM03 – B02BM03

• To order the one-piece Thermoplastic Hose End that uses U800 Ferrules substitute a ‘C’ for the ‘U’ i.e. U02BM03 – C02BM03

Please reference Hose type to find the Ferrule needed for the Thermoplastic one-piece Hose End.


FITTINGS

J.I.C. MALE

J.I.C THREAD DASH NUMBER NORMAL HOSE BORE PART

NUMBER A/F DIM A DIM B DIM C

MM IN DASH

7/16” X 20 04 6 1/4 04 A04JM04 13.0 28.2 14.0 4.0

1/2” X 20 05 6 1/4 04 A05JM04 13.0 29.2 14.0 4.0

9/16” X 18 06 6 1/4 04 A06JM04 16.0 29.2 14.0 4.0

7/16” X 20 04 10 3/8 06 A04JM06 15.9 29.7 14.0 7.0

1/2” X 20 05 10 3/8 06 A05JM06 17.0 29.7 14.0 5.5

9/16” X 18 06 10 3/8 06 A06JM06 16.0 29.7 14.0 7.0

3/4" X 16 08 10 3/8 06 A08JM06 19.0 34.5 16.5 7.0

9/16” X 18 06 12 1/2 08 A06JM08 19.0 32.3 14.0 9.3

3/4" X 16 08 12 1/2 08 A08JM08 22.0 34.8 16.5 9.3

7/8” X 14 10 12 1/2 08 A10JM08 24.0 39.3 19.5 9.3

3/4" X 16 08 16 5/8 10 A08JM10 22.2 34.9 16.5 12.0

7/8” X 14 10 16 5/8 10 A10JM10 24.0 39.4 19.5 12.0

1-1/16” X 12 12 16 5/8 10 A12JM10 27.0 43.2 22.0 12.0

7/8” X 14 10 19 3/4 12 A10JM12 27.0 40.3 19.5 15.0

1-1/16” X 12 12 19 3/4 12 A12JM12 27.0 44.1 22.0 15.0

1-5/16” X 12 16 19 3/4 12 A16JM12 36.0 47.1 23.0 15.0

1-1/16” X 12 12 25 1 16 A12JM16 31.8 47.1 22.0 19.5

1-5/16” X 12 16 25 1 16 A16JM16 36.0 48.1 23.0 19.5

1-5/8” X 12 20 25 1 16 A20JM16 46.0 53.3 24.3 19.5

1-5/16” X 12 16 31 1-1/4 20 A16JM20 41.3 52.3 23.0 26.0

1-5/8” X 12 20 31 1-1/4 20 A20JM20 46.0 53.5 24.3 26.0


FITTINGS

J.I.C. FEMALE LOOSE NUT



MM IN DASH

1/2” X 20 05 6 1/4 04 A05JM04 17 15.0 9.5 4.0

9/16” X 18 06 6 1/4 04 A06JM04 19 16.0 8.7 4.0

3/4” X 16 08 10 3/8 06 A08JM06 22 18.1 10.7 7.0

7/8” X 14 10 10 3/8 06 A10JM06 27 19.5 13.7 7.0

7/8” X 14 10 12 1/2 08 A10JM08 27 19.8 13.7 9.3

1-1/16” X 12 12 12 1/2 08 A12JM08 32 21.7 15.0 9.3

1-1/16" X 12 12 16 5/8 10 A12JM10 32 21.8 15.0 12.0


FITTINGS

J.I.C. FEMALE WIRED ON NUT



MM IN DASH

7/16” X 20 04 6 1/4 04 A04JF04 14 15.5 8.4 4.0

7/16” X 20 04 10 3/8 06 A04JF06 14 16.0 8.4 7.0

1/2” X 20 05 10 3/8 06 A05JF06 17 16.5 9.5 4.0

9/16” X 18 06 10 3/8 06 A06JF06 19 16.2 8.7 7.0

9/16” X 18 06 12 1/2 08 A06JF08 19 16.5 8.7 9.3

3/4” X 16 08 12 1/2 08 A08JF08 22 17.6 10.7 9.3

3/4" X 16 08 16 5/8 10 A08JF10 22 18.2 10.7 12.0

7/8” X 14 10 16 5/8 10 A10JF10 27 19.7 13.7 12.0

1-3/16” X 12 14 19 3/4 12 A10JF12 36 22.3 14.7 15.0

1-1/16” X 12 12 19 3/4 12 A12JF12 32 21.8 15.0 15.0

1-5/16” X12 16 19 3/4 12 A16JF12 41 23.1

1

16.8 15.0

1-1/16” X12 12 25 1 16 A12JF16 32 23.8 15.0 15.0

1-5/16” X 12 16 25 1 16 A16JF16 41 24.1 16.8 19.5

1-5/8” X12 20 25 1 16 A20JF16 50 28.7 16.1 19.5

1-5/16” X 12 16 31 1-1/4 20 A16JF20 41 24.4 16.8 26.0

1-5/8” X 12 20 31 1-1/4 20 A20JF20 50 28.5 18.1 26.0

1-7/8” X 12 24 31 1-1/4 20 A24JF20 60 29.7 19.4 26.0


FITTINGS

J.I.C. FEMALE 90° SWEPT ELBOW LOOSE NUT


NUMBER A/F DIM A DIM B DIMC DIM D

MM IN DASH

1/2” X 20 05 6 1/4 04 A05JF90S04 17 27.2 27.2 9.5 4.0

9/16” X 18 06 6 1/4 04 A06JF90S04 19 27.2 28.2 8.7 4.0

3/4” X 16 08 10 3/8 06 A08JF90S06 22 31.5 32.3 10.7 7.0

7/8” X 14 10 12 1/2 08 A10JF90S08 27 42.3 39.2 13.7 9.3

1-1/16” X 12 12 12 1/2 08 A12JF90S08 32 42.3 42.6 15.0 9.3

1-1/16” X 12 12 16 5/8 10 A12JF90S10 32 47.8 51.8 15.0 12.0


FITTINGS

J.I.C. FEMALE 90° SWEPT ELBOW WIRED ON NUT


NUMBER A/F DIM A DIM B DIM C DIM D

MM IN DASH

7/16” X 20 04 6 1/4 04 A04JF90S04 14 27.2 32.4 8.4 4.0

7/16” X 20 04 10 3/8 06 A04JF90S06 14 31.5 35.1 8.4 7.0

9/16” X 18 06 10 3/8 06 A06JF90S06 19 31.5 35.3 8.7 7.0

9/16” X 18 06 12 1/2 08 A06JF90S08 19 42.3 39.9 8.7 9.3

3/4” X 16 08 12 1/2 08 A08JF90S08 22 42.3 41.0 10.7 9.3

3/4” X 16 08 16 5/8 10 A08JF90S10 22 47.6 50.3 10.7 12.0

7/8” X 14 10 16 5/8 10 A10JF90S10 27 47.6 51.8 13.7 12.0

1-1/16” X 12 12 19 3/4 12 A12JF90S12 32 53.8 61.0 15.0 15.0

1-5/16” X 12 16 19 3/4 12 A16JF90S12 41 53.8 63.1 16.8 15.0

1-5/16” X 12 16 25 1 16 A16JF90S16 41 63.8 75.1 16.8 19.5

1-5/8” X 12 20 25 1 16 A20JF90S16 50 63.8 78.0 16.1 19.5

1-5/8” X 12 20 31 1-1/4 20 A20JF90S20 50 81.0 91.1 16.1 26.0

1-7/8” X 12 24 31 1-1/4 20 A24JF90S20 60 81.0 90.5 19.4 26.0


FITTINGS

J.I.C. FEMALE 45° SWEPT ELBOW LOOSE NUT



MM IN DASH

1/2” X 20 05 6 1/4 04 A05JF45S04 17 32.4 13.4 9.5 4.0

9/16” X 18 06 6 1/4 04 A06JF45S04 19 33.1 14.1 8.7 4.0

3/4” X 16 08 10 3/8 06 A08JF45S06 22 37.8 16.0 10.7 7.0

7/8” X 14 10 12 1/2 08 A10JF45S08 27 49.2 19.2 13.7 9.3

1-1/16” X 12 12 16 5/8 10 A12JF45S10 32 57.2 25.4 15.0 12.0


FITTINGS

J.I.C. FEMALE 45° SWEPT ELBOW WIRED ON NUT



MM IN DASH

7/16” X 20 04 6 1/4 04 A04JF45S04 14 36.1 17.1 8.4 4.0

7/16” X 20 04 10 3/8 06 A04JF45S06 14 39.8 18.0 8.4 7.0

9/16” X 18 06 10 3/8 06 A06JF45S06 19 40.0 18.1 8.7 7.0

9/16” X 18 06 12 1/2 08 A06JF45S08 19 49.5 19.5 8.7 9.3

3/4” X 16 08 12 1/2 08 A08JF45S08 22 50.3 20.3 10.7 9.3

3/4” X 16 08 16 5/8 10 A08JF45S10 22 56.2 24.4 10.7 12.0

7/8” X 14 10 16 5/8 10 A10JF45S10 27 57.2 25.4 13.7 12.0

1-1/16” X 12 12 19 3/4 12 A12JF45S12 32 65.1 30.0 15.0 15.0

1-5/16” X 12 16 25 1 16 A16JF45S16 41 77.9 37.0 16.8 19.5

1-5/8” X 12 20 25 1 16 A20JF45S16 50 79.9 39.0 16.1 19.5

1-5/8” X 12 20 31 1-1/4 20 A20JF45S20 50 97.4 44.5 16.1 26.0

1-7/8” X 12 24 31 1-1/4 20 A24JF45S20 60 97.0 44.1 19.4 26.0


FITTINGS

J.I.C. FEMALE EQUAL HEXAGON WIRED ON NUT


NUMBER A/F1 A/F2 DIM A DIM B DIM C

MM IN DASH

7/16” X 20 04 6 1/4 04 A04HJF04 14 14 20.3 8.4 4.0

9/16” X 18 06 6 1/4 04 A06HJF04 19 19 22.1 8.7 4.0

9/16” X 18 06 10 3/8 06 A06HJF06 19 19 23.1 8.7 7.0

3/4” X 16 08 12 1/2 08 A08HJF08 22 22 25.0 10.7 9.3

7/8” X 14 10 12 1/2 08 A10HJF08 27 27 28.2 13.7 9.3

1-1/16” X 12 12 19 3/4 12 A12HJF12 32 32 32.0 15.0 15.0

1-5/16” X 12 16 25 1 16 A16HJF16 41 41 36.3 16.8 19.5

1-5/8” X 12 20 31 1-1/4 20 A20HJF20 50 50 45.3 16.1 26.0


FITTINGS

N.P.T.F. MALE

N/P.T.F THREAD SIZE DASH NUMBER NORMAL HOSE BORE PART


MM IN DASH

1/8” X 27 02 6 1/4 04 A02NM04 13 23.7 9.5 4.0

1/4” X 18 04 6 1/4 04 A04NM04 14 29.7 14.5 4.0

3/8” X 18 06 6 1/4 04 A06NM04 19 32.0 14.5 4.0

1/4” X 18 04 10 3/8 06 A04NM06 17 30.2 14.5 7.0

3/8” X 18 06 10 3/8 06 A06NM06 19 32.5 14.5 7.0

1/2” X 14 08 10 3/8 06 A08NM06 24 38.8 19.3 7.0

3/8” X 18 06 12 1/2 08 A06NM08 22 32.5 14.5 9.3

1/2" X 14 08 12 1/2 08 A08NM08 24 39.1 19.3 9.3

3/4" X 14 12 19 3/4 12 A12NM12 27 41.4 19.3 15.0

1” X 11.5 16 25 1 16 A16NM16 36 46.9 23.8 19.5

1-1/4” X 11.5 20 31 1-1/4 20 A20NM20 46 56.5 24.6 26.0


FITTINGS

N.P.T.F. SWIVEL MALE

N/P.T.F THREAD SIZE DASH NUMBER NORMAL HOSE BORE PART


MM IN DASH

1/4” X 18 04 6 1/4 04 A04NMS04 17 38.3 14.5 4.0

1/4” X 18 04 10 3/8 06 A04NMS06 17 38.8 14.5 4.0

3/8” X 18 06 10 3/8 06 A06NMS06 22 39.2 14.5 7.0

1/2” X 14 08 12 1/2 08 A08NMS08 27 46.2 19.3 9.3

3/4” X 14 12 19 3/4 12 A12NMS12 32 48.5 19.3 15.0

1” X 11.5 16 25 1 16 A16NMS16 38 57.7 23.8 19.5

N.P.S.M. FEMALE LOOSE NUT AIRLESS PAINT SPRAY

NPSM THREAD SIZE DASH NUMBER NORMAL HOSE BORE PART


MM IN DASH

1/4” 04 8 1/4 04 A04NSF04 19 16.5 4.2 4.0

3/8” 06 10 3/8 06 A06NSF06 22 19.6 5.3 7.0

1/2" 08 12 1/2 08 A08NSF08 27 20.8 6.4 9.3

3/4" 12 19 3/4 12 A12NSF12 – – – –


FITTINGS

N.P.S.M. FEMALE WIRED ON NUT AIRLESS PAINT SPRAY

NPSM THREAD SIZE DASH NUMBER NORMAL HOSE BORE PART


MM IN DASH

1/4” 04 10 3/8 06 A04NSF06 19 18.7 5.2 4.0


FITTINGS

S.A.E “O” RING MALE

SAE THREAD DASH NUMBER NORMAL HOSE BORE PART


MM IN DASH

7/16” X 20 04 6 1/4 04 A04SMR04 14.3 24.3 9.1 4.0

9/16” X 18 06 10 3/8 06 A06SMR06 17.5 25.7 10.0 7.0

3/4" X 16 08 12 1/2 08 A08SMR08 22.2 30.9 11.1 9.3

7/8” X 14 10 12 1/2 08 A10SMR08 27.0 28.7 12.7 9.3

3/4" X 16 08 16 5/8 10 A08SMR10 22.2 31.0 11.1 12.0

7/8” X 14 10 16 5/8 10 A10SMR10 27.0 32.6 12.7 12.0

1-1/16” X12 12 19 3/4 12 A12SMR12 31.8 39.2 15.1 15.0

1-5/16” X 12 16 25 1 16 A16SMR16 41.3 41.7 15.1 19.5

1-5/8” X 12 20 31 1-1/4 20 A20SMR20 50.8 47.0 15.1 26.0

S.A.E SWIVEL MALE

SAE THREAD DASH NUMBER NORMAL HOSE BORE PART


MM IN DASH

7/16” X 20 04 6 1/4 04 A04SMRS04 17.5 34.7 9.1 4.0

9/16” X 18 06 10 3/8 06 A06SMRS06 20.6 36.7 10.0 7.0

3/4" X 16 08 12 1/2 08 A08SMRS08 28.7 41.6 11.1 9.3

1-1/16” X 12 12 19 3/4 12 A12SMRS12 31.8 47.0 15.1 15


FITTINGS

N.P.T.F. FIXED FEMALE

N/P.T.F THREAD DASH NUMBER NORMAL HOSE BORE PART

NUMBER A/F DIM B DIM C

MM IN DASH

1/4” X 18 04 6 1/4 04 A04FNF04 19.0 25.3 4.0

3/8” X 18 06 6 1/4 04 A06FNF04 22.2 25.7 4.0

1/4” X 18 04 10 3/8 06 A04FNF06 19.0 26.3 7.0

1/2" X 14 08 10 3/8 06 A08FNF06 27.0 31.1 7.0

3/8” X 18 06 12 1/2 08 A06FNF08 22.2 26.9 9.3

1/2” X 14 08 12 1/2 08 A08FNF08 27.0 31.4 9.3

3/4” X 14 12 19 3/4 12 A12FNF12 41.3 34.5 15.0


CoverRubber_FinalThermoplastic_FinalFittings_FinalBack Cover

RUBBER HOSES · 2018. 12. 10. · U8000-08 21.68 NOTE: When using the “U” series ferrule with an ‘X’ series insert crimp to the above specified diameter +/- 0.13MM IMPORTANT:

Documents