Page 1 of 1 Procurement Management Department 2115 Second Floor, 1 st Floor Fort Myers, FL 33901 Main Line: (239) 533-8881 Fax Line: (239) 485-8383 www.leegov.com/procurement Posted Date: June 3, 2021 Solicitation No.: B210165RJD Solicitation Name: Estero Blvd and Crescent St Intersection Improvements - LAP Subject: Addendum Number 1 The following represents clarification, additions, deletions, and/or modifications to the above referenced bid. This addendum shall hereafter be regarded as part of the solicitation. Items not referenced herein remain unchanged, including the response date. Words, phrases or sentences with a strikethrough represent deletions to the original solicitation. Underlined words and bolded, phrases or sentences represent additions to the original solicitation. 1. ATTACHMENT: • Proprietary Product – FPID # 444923-2-58-01 Proprietary List o 715-010-002 LED Luminaire Wildlife BOW LX 2. REVISED PLANS: • Sheets 1, 2A, 7, 15 have been revised and have been uploaded to the project webpage on the Lee County Procurement website under the project Addendum section. Please ensure that your firm has downloaded the revised sheet set. Bidders are required to acknowledge this addendum per Form 1 – Solicitation Response Form. 3. QUESTIONS / ANSWERS No questions have been submitted at this time. BIDDER/PROPOSER IS ADVISED, YOU ARE REQUIRED TO ACKNOWLEDGE RECEIPT OF THIS ADDENDUM WHEN SUBMITTING A BID/PROPOSAL. FAILURE TO COMPLY WITH THIS REQUIREMENT MAY RESULT IN THE BIDDER/PROPOSER BEING CONSIDERED NON-RESPONSIVE. ALL OTHER TERMS AND CONDITIONS OF THE SOLICITATION DOCUMENTS ARE AND SHALL REMAIN THE SAME. Robin Dennard Robin Dennard Procurement Analyst Direct Line: 239-533-8837 Lee County Procurement Management
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1 of 1
Procurement Management Department 2115 Second Floor, 1st Floor
Posted Date: June 3, 2021 Solicitation No.: B210165RJD Solicitation Name: Estero Blvd and Crescent St Intersection Improvements - LAP Subject: Addendum Number 1 The following represents clarification, additions, deletions, and/or modifications to the above referenced bid. This addendum shall hereafter be regarded as part of the solicitation. Items not referenced herein remain unchanged, including the response date. Words, phrases or sentences with a strikethrough represent deletions to the original solicitation. Underlined words and bolded, phrases or sentences represent additions to the original solicitation.
2. REVISED PLANS: • Sheets 1, 2A, 7, 15 have been revised and have been uploaded to the project webpage on the Lee County
Procurement website under the project Addendum section. Please ensure that your firm has downloaded the revised sheet set. Bidders are required to acknowledge this addendum per Form 1 – Solicitation Response Form.
3. QUESTIONS / ANSWERS
No questions have been submitted at this time.
BIDDER/PROPOSER IS ADVISED, YOU ARE REQUIRED TO ACKNOWLEDGE RECEIPT OF THIS ADDENDUM WHEN SUBMITTING A BID/PROPOSAL. FAILURE TO COMPLY WITH THIS REQUIREMENT MAY RESULT IN THE BIDDER/PROPOSER BEING CONSIDERED NON-RESPONSIVE. ALL OTHER TERMS AND CONDITIONS OF THE SOLICITATION DOCUMENTS ARE AND SHALL REMAIN THE SAME. Robin Dennard Robin Dennard Procurement Analyst Direct Line: 239-533-8837 Lee County Procurement Management
Mr. Mark Peronto, P.E. FDOT District 1 Design Engineer Florida Department of Transportation District 1 Lee County, Florida
Re: FPN 444923-2-58-01 - Estero Blvd @ Crescent St
Dear Mr. Peronto:
Lee County Department of Transportation (LCDOT) maintains approximately 6,500 streetlights throughout Lee County and has agreements with the Florida Department of Transportation (FDOT) within Lee County to provide maintenance of the streetlights on non-county maintained facilities.
Lee County is standardizing on a Wildlife Friendly/Turtle Safe Roadway lighting fixtures for all new construction projects currently and in the near future. We have reviewed the two Wildlife friendly/Turtle safe fixtures that are on the FDOT APL (Autobahn ATB2 and Visionaire Lighting BOW LX II) and after extensive review and comparing photometric lighting levels. We have decided we want to move forward with the Visionaire Lighting BOW LX II, part of our decision for this fixture has a lot to do with the reliability and deficiencies that we LCDOT and FDOT has seen in Autobahn ATB2/ATBL Roadway fixtures. By Lee County standardizing on the Visionaire BOW LX II Lighting fixture, we will be able to keep an inventory in our warehouse and be able to efficiently respond to outages and make the necessary repairs.
Based on the reasons described in this letter, Lee County requests that FDOT approve the proprietary product justification to use the Visionaire Lighting BOW LX II fixture for the wildlife friendly/Turtle Safe Lighting for this project.
Kevin Ruane District One Cecil L Pendergrass District Two Ray Sandelli District Three Brian Hamman District Four Frank Mann District Five Roger Desjarlais County Manager Richard Wm. Wesch County Attorney Donna Marie Collins County Hearing Examiner
Board of County Commissioners
P.O. Box 398, Fort Myers, Florida 33902-0398 | (239) 533-2111 | leegov.com AN EQUAL OPPORTUNITY EMPLOYER
Ryan Kirsch Project Manager Lee County Department of Transportation Enclosure: Proprietary Product Certification - Roadway/Intersection Lighting CC: D’Juan L. Harris - FDOT Robert K. Phelan - LCDOT Robert L. Price - LCDOT Steve Jansen - LCDOT Michael Padgett - LCDOT Daniel Craig - CARDNO
FPID # 444923-2-58-01 Proprietary List APL Certification Description Manufacturer 1 715-010-002 LED Luminaire Wildlife
Financial Project ID: 444923-2-58-01 Federal Aid Number:
Date: 05/21/2021
New Const. (X) RRR ( )
Project Name: Estero Blvd @ Crescent St___________________ State Road Number: Begin Project MP:
Co. /Sec. /Sub. End Project MP:
Full Federal Oversight: No (X ) Yes ( ) Note: if Yes, submit to appropriate Federal Agency Director.
A justification and all supporting documents must be attached to this document. Mark the appropriate certification:
"I Ryan Kirsch , Project Manager , of the Lee County DOT – Traffic ,
Print Name of Initiator Position title Name of agency
do hereby certify that in accordance with the requirements of 23 CFR 635.411(a)(2), Mark Appropriately:
(X) that this patented or proprietary item is essential for synchronization with existing highway facilities.
( ) that no equally suitable alternative exists for this patented or proprietary item.
, 05/21/2021 Signature Date
For Department Use Only
"I , , Print Name Position title
of the Florida Department of Transportation, do hereby recommend approval of this certification request made in accordance with the requirements of 23 CFR 635.411(a)(2), Mark Appropriately:
( ) that this patented or proprietary item is essential for synchronization with existing highway facilities. ( ) that no equally suitable alternative exists for this patented or proprietary item. Identify any conditions and/or limitations on an attached memo.
, Signature Date
For Federal Use Only (use for Full Federal Oversight projects)
"I , ,
Print Name Position title
of the , do hereby approve this certification request Agency
made in accordance with the requirements of 23 CFR 635.411(a)(2).. Identify any conditions and/or limitations on an attached memo.
, Signature Date
Ryan KirschDigitally signed by Ryan KirschDN: C=US, [email protected], O=Lee County DOT Traffic, CN=Ryan KirschReason: I am the author of this documentDate: 2021.05.21 17:40:25-04'00'
The new BOW LX-II LED Series continues the unique contemporary design inspired by the sleek styling of the BOW family. Separating the extruded aluminum driver housing and the individual die-cast aluminum linear LED engines: optimize the life of the LEDs and the Driver(s); and maximizes the lumen output of the fixture. The adjustable knuckle allows for up to 90° degrees of vertical adjustment for putting the light exactly where you need it.
Each of the individual LED light engines come with 32 LEDs; for a max total of 256 LEDs. Ten optical distribution patterns are available.
A unique Type 4-A automotive distribution pattern is available for the front rows of Auto Dealerships. 590 nm diode supplied as standard.
A durable polyester powder coat finish is guaranteed for five years; and is available in standard or custom colors.
The BOW LX-II LED series is an exceptional choice for auto dealerships, shopping centers, commercial parking lots and general area lighting.
Ordering Information
19645 Rancho Way • Rancho Dominguez, CA 90220 • Phone: 310 512 6480 Fax 310 512 6486www.visionairelighting.com
HousingThe LED light engines are constructed of heavy-duty, die-cast aluminum, with external heat radiating fins.
Driver Compartment The separate driver housing is constructed of extruded aluminum, with vented cast aluminum end covers and stainless steel fasteners; for easy access to the LED driver(s); allowing for cooler operation and longer driver life. One-piece gasketing is utilized throughout the fixture for weather tight operation.
Thermal Management• The BOW LX-II Series provides excellent overall thermal management by maximizing the fixture’s heat sink capabilities. This enables the BOW LX-II Series to withstand higher ambient temperatures and drive currents without degrading LED life.• The L70 test determines the point in an LEDs life when it reaches 70 percent of its initial output. The BOW LX-II Series LEDs have been determined to last a minimum of 100,000 hours in 25°C environments when driven at 350 mA.
Optical System• The highest lumen output, LEDs are utilized in the BOW LX-II Series.• IES distribution Types FM, FN, 1, 2, 3, 4, 4A, 5, 5W and 5WR are available. • LED light engines come in multiples of 32 LEDs.• 590 nm diode suppled as standard.
Quali-Guard® Finish• The finish is a Quali-Guard® textured, chemically pretreated through a multiple-stage washer, electrostatically applied, thermoset polyester powder coat finish, with a minimum of 3-5 millimeter thickness. Finish is oven-baked at 400° F to promote maximum adherence and finish hardness.• All finishes are available in standard and custom colors. • Finish is guaranteed for five (5) years.
Mounting• The Bolt -On Arm (BOA) utilizes a 2 piece cleat system for easy installa-tion. A Round Pole Plate Adaptor (RPP) is required for mounting to round poles.• Mast Arm Fitter fits over a 2 3/8” tenon.• Bolt-On Arm Wall Plate• Bolt-On Arm Wall Plate-XL
Electrical Assembly• The BOW LX-II Series is supplied with a choice of 350 or 530 mA high-performance LED drivers, that accept 120v thru 480v, 50 Hz to 60 Hz, input.• Power factor of 90%.• Rated for -40 °C to +55 º C operations. • THD less than or equal to 20% • 20 kV surge protector supplied as standard.• 0-10v Dimming Driver supplied as standard.
Warranty• Five (5) year Limited Warranty on entire system, including finish. For full warranty information, please visit VisionaireLighting.com.
Options• Button Type Photocell• Photocell & Receptacle• Photo Receptacle• Round pole plate adaptor• Motion Sensor• Pole Mounted Motion Sensor• Universal Pole Mount Adaptor (BLX-II-3, BLX-II-4 & BLX-II-6 Only)• Decorative Shroud
Listings• BOW LX-II Series is cUL listed, suitable for wet locations• LM79 and LM80 • RoHS compliant• Meets ANSI C136.31-2010 3G Vibration Standards for: Mast Arm Mount BOA• Powder Coated Tough™• IP65 Rated• IDA Certification• Turtle Safe• Certified Wildlife Lighting
Project Name:
Catalog Number:
Type:
VISIONAIRE LIGHTING
Features & SpecificationsBLX-II Wildlife Certified LED Specifications BLX-II Wildlife Certified
BLX-II-4 Post Top Mount Shown
BLX-II-3
BLX-II-4
BLX-II-6
BLX-II-8
96LC
128LC
192LC
256LC
3350mA
5530mA
TS590 nm
GYGrey
SLSilver Metallic
BKBlack
SBKSmooth Black
WHWhite
SWHSmooth White
BZBronze
GPGraphite
CCCustom Color
UNV120-277V
8347V
5480V
MODEL
PCR-120Photocell & Receptacle
PCR-208Photocell & Receptacle
PCR-240Photocell & Receptacle
PCR-277Photocell & Receptacle
PCR-480Photocell & Receptacle
PER3 Pin Photo Receptacle
w/shorting cap
5PINPER5 Pin Photo Receptacle
w/shorting capRequires Dimming Driver
7PINPER7 Pin Photo Receptacle
w/shorting capRequires Dimming Driver
DIM0-10v Dimming Driver
No Controls
WSC-8Motion Sensor
8’ Mounting Height
WSC-20Motion Sensor
9-20’ Mounting Height
WSC-40Motion Sensor
21-40’ Mounting Height
The WSC option will require(1) FSIR 100
remote for programing
VWCVisionaire
Wireless ControlsConsult Factory
RPPRound Pole
Plate AdaptorFor 3ӯ - 5ӯ Pole
UPMA-SUniversal Square Pole
Mount AdaptorNot available with
BLX-II-8
UPMA-RUniversal Round Pole
Mount AdaptorNot available with
BLX-II-8
DSDecorative Shroud
ROT-RRotated Optics
Right Side
ROT-LRotated Optics
Left Side
LSLight Shield
OPTICS LEDS CURRENT KELVIN VOLTAGE MOUNTING FINISH OPTIONS OPTIONS
MAMast Arm Fitter
BOABolt-On Arm
AMArm Mount
Extended arm is neededfor the BLX-6 & BLX-8 in D9, T9, T120 & QD
configurations
WMWall Mount
BLX-II-3 & BLX-II-4 Only
BAWPBolt-On Arm
Wall PlateBLX-3 & BLX-4 only
BAWP-XLBolt-On ArmWall Plate-XL
BLX-6 & BLX-8 only
The Wildlife Lighting Program was developed by the Department of the Interior’s U.S. Fish and Wildlife Service and the Florida Fish and Wildlife Conservation Commission to address light pollution issues in ecologically sensitive areas while ensuring human safety and security.
The new BOW LX-II LED Series continues the unique contemporary design inspired by the sleek styling of the BOW family. Separating the extruded aluminum driver housing and the individual die-cast aluminum linear LED engines: optimize the life of the LEDs and the Driver(s); and maximizes the lumen output of the fixture. The adjustable knuckle allows for up to 90° degrees of vertical adjustment for putting the light exactly where you need it.
Each of the individual LED light engines come with 32 LEDs; for a max total of 256 LEDs. Ten optical distribution patterns are available.
A unique Type 4-A automotive distribution pattern is available for the front rows of Auto Dealerships. 590 nm diode supplied as standard.
A durable polyester powder coat finish is guaranteed for five years; and is available in standard or custom colors.
The BOW LX-II LED series is an exceptional choice for auto dealerships, shopping centers, commercial parking lots and general area lighting.
Ordering Information
19645 Rancho Way • Rancho Dominguez, CA 90220 • Phone: 310 512 6480 Fax 310 512 6486www.visionairelighting.com
HousingThe LED light engines are constructed of heavy-duty, die-cast aluminum, with external heat radiating fins.
Driver Compartment The separate driver housing is constructed of extruded aluminum, with vented cast aluminum end covers and stainless steel fasteners; for easy access to the LED driver(s); allowing for cooler operation and longer driver life. One-piece gasketing is utilized throughout the fixture for weather tight operation.
Thermal Management• The BOW LX-II Series provides excellent overall thermal management by maximizing the fixture’s heat sink capabilities. This enables the BOW LX-II Series to withstand higher ambient temperatures and drive currents without degrading LED life.• The L70 test determines the point in an LEDs life when it reaches 70 percent of its initial output. The BOW LX-II Series LEDs have been determined to last a minimum of 100,000 hours in 25°C environments when driven at 350 mA.
Optical System• The highest lumen output, LEDs are utilized in the BOW LX-II Series.• IES distribution Types FM, FN, 1, 2, 3, 4, 4A, 5, 5W and 5WR are available. • LED light engines come in multiples of 32 LEDs.• 590 nm diode suppled as standard.
Quali-Guard® Finish• The finish is a Quali-Guard® textured, chemically pretreated through a multiple-stage washer, electrostatically applied, thermoset polyester powder coat finish, with a minimum of 3-5 millimeter thickness. Finish is oven-baked at 400° F to promote maximum adherence and finish hardness.• All finishes are available in standard and custom colors. • Finish is guaranteed for five (5) years.
Mounting• The Bolt -On Arm (BOA) utilizes a 2 piece cleat system for easy installa-tion. A Round Pole Plate Adaptor (RPP) is required for mounting to round poles.• Mast Arm Fitter fits over a 2 3/8” tenon.• Bolt-On Arm Wall Plate• Bolt-On Arm Wall Plate-XL
Electrical Assembly• The BOW LX-II Series is supplied with a choice of 350 or 530 mA high-performance LED drivers, that accept 120v thru 480v, 50 Hz to 60 Hz, input.• Power factor of 90%.• Rated for -40 °C to +55 º C operations. • THD less than or equal to 20% • 20 kV surge protector supplied as standard.• 0-10v Dimming Driver supplied as standard.
Warranty• Five (5) year Limited Warranty on entire system, including finish. For full warranty information, please visit VisionaireLighting.com.
Options• Button Type Photocell• Photocell & Receptacle• Photo Receptacle• Round pole plate adaptor• Motion Sensor• Pole Mounted Motion Sensor• Universal Pole Mount Adaptor (BLX-II-3, BLX-II-4 & BLX-II-6 Only)• Decorative Shroud
Listings• BOW LX-II Series is cUL listed, suitable for wet locations• LM79 and LM80 • RoHS compliant• Meets ANSI C136.31-2010 3G Vibration Standards for: Mast Arm Mount BOA• Powder Coated Tough™• IP65 Rated• IDA Certification• Turtle Safe• Certified Wildlife Lighting
Project Name:
Catalog Number:
Type:
VISIONAIRE LIGHTING
Features & SpecificationsBLX-II Wildlife Certified LED Specifications BLX-II Wildlife Certified
BLX-II-4 Post Top Mount Shown
BLX-II-3
BLX-II-4
BLX-II-6
BLX-II-8
96LC
128LC
192LC
256LC
3350mA
5530mA
TS590 nm
GYGrey
SLSilver Metallic
BKBlack
SBKSmooth Black
WHWhite
SWHSmooth White
BZBronze
GPGraphite
CCCustom Color
UNV120-277V
8347V
5480V
MODEL
PCR-120Photocell & Receptacle
PCR-208Photocell & Receptacle
PCR-240Photocell & Receptacle
PCR-277Photocell & Receptacle
PCR-480Photocell & Receptacle
PER3 Pin Photo Receptacle
w/shorting cap
5PINPER5 Pin Photo Receptacle
w/shorting capRequires Dimming Driver
7PINPER7 Pin Photo Receptacle
w/shorting capRequires Dimming Driver
DIM0-10v Dimming Driver
No Controls
WSC-8Motion Sensor
8’ Mounting Height
WSC-20Motion Sensor
9-20’ Mounting Height
WSC-40Motion Sensor
21-40’ Mounting Height
The WSC option will require(1) FSIR 100
remote for programing
VWCVisionaire
Wireless ControlsConsult Factory
RPPRound Pole
Plate AdaptorFor 3ӯ - 5ӯ Pole
UPMA-SUniversal Square Pole
Mount AdaptorNot available with
BLX-II-8
UPMA-RUniversal Round Pole
Mount AdaptorNot available with
BLX-II-8
DSDecorative Shroud
ROT-RRotated Optics
Right Side
ROT-LRotated Optics
Left Side
LSLight Shield
OPTICS LEDS CURRENT KELVIN VOLTAGE MOUNTING FINISH OPTIONS OPTIONS
MAMast Arm Fitter
BOABolt-On Arm
AMArm Mount
Extended arm is neededfor the BLX-6 & BLX-8 in D9, T9, T120 & QD
configurations
WMWall Mount
BLX-II-3 & BLX-II-4 Only
BAWPBolt-On Arm
Wall PlateBLX-3 & BLX-4 only
BAWP-XLBolt-On ArmWall Plate-XL
BLX-6 & BLX-8 only
The Wildlife Lighting Program was developed by the Department of the Interior’s U.S. Fish and Wildlife Service and the Florida Fish and Wildlife Conservation Commission to address light pollution issues in ecologically sensitive areas while ensuring human safety and security.
Motion Sensor Default Setting
Type High Mode
Low Mode
Time Delay
Cut off Delay Sensitivity Hold Off
SetpointPhotocell On/Off
Ramp Up Time
Fade Down Time
WSC - Default 10V 1V 5 Min 1 Hour Max Disabled Disabled Disabled Disabled
WSC Range 0 -10V 0 - 9.8V 5 - 30 Min 1 - 5 Hours Low, Med, Max 1 - 250FC 1 - 250FC 1 - 60 Dec 1-60 Dec
The Bolt-On Arm (BOA) utilizes a 2 piece cleat system for easy installa-tion. A Round Pole Plate Adaptor (RPP) is required for mounting to round poles.
LED Specifications BLX-II Wildlife CertifiedBLX-II Wildlife Certified LED Specifications
19645 Rancho Way • Rancho Dominguez, CA 90220 • Phone: 310 512 6480 Fax 310 512 6486www.visionairelighting.comVISIONAIRE LIGHTING
The Bolt-On Arm (BOA) utilizes a 2 piece cleat system for easy installa-tion. A Round Pole Plate Adaptor (RPP) is required for mounting to round poles.
LED Specifications BLX-II Wildlife CertifiedBLX-II Wildlife Certified LED Specifications
19645 Rancho Way • Rancho Dominguez, CA 90220 • Phone: 310 512 6480 Fax 310 512 6486www.visionairelighting.comVISIONAIRE LIGHTING