1 Tombstone Ring Toss Pegboards: 2 large squares 1 large circle Other: Heavy cardboard Glue or velcro Bead Colors: Magenta - 54 Orange - 54 Creme - 36 Cheddar - 8 Prickly Pear - 54 Kiwi Lime - 54 Pastel Green - 28 Green - 14 Dark Green - 198 Turquoise - 54 Plum - 54 Purple - 54 Light Brown - 112 Brown - 603 Grey - 944 Dark Grey - 396 Black - 766 White - 58 Raspberry Pearl Stripe - 48 Fire Stripe - 48 Prickly Pear Pearl Stripe - 48 Cucumber Stripe - 84 Royal Blue Pearl Stripe - 48 Starry Nite Stripe - 48 Grape Stripe - 48 Monkey Stripe - 150 Zebra Stripe - 70 Silver Pearl Stripe - 124 Instructions 1. Place your beads on the pegboards as shown. If you are using a clear pegboard, slide the actual-size pattern underneath it. 2. Ask an adult to fuse your designs—see page 9 for further instructions. 3. Assembly: see page 10. YOU WILL NEED: RIP Tombstone Tombstone Ring Toss Game Create a spooky cemetery scene on a heavy cardboard surface using the Perler pieces and your favorite props. Glue or velcro your pieces in place. Determine where the player must stand to play. Assign points for successfully ringing the various objects: • 10 points for either of the small tombstones • 30 points for the skull tombstones • 40 points for the RIP tombstone • 50 points for either of the zombie hands alone • 100 points for the tree monster top or arms • Hit the gates at all, you lose all your points!
10
Embed
RIP Tombstone Tombstone Ring Toss Gamedemandware.edgesuite.net/.../Tombstone-Ring-Toss.pdfTombstone Ring Toss Rings: Using the same pattern, make 9 rings in the color combinations.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Instructions1. Place your beads on the pegboards as shown. If you are using a clear
pegboard, slide the actual-size pattern underneath it.2. Ask an adult to fuse your designs—see page 9 for further instructions.3. Assembly: see page 10.
YOU WILL NEED:
RIP Tombstone
Tombstone Ring Toss GameCreate a spooky cemetery scene on a heavy cardboard surface using the Perler pieces and your favorite props. Glue or velcro your pieces in place.
Determine where the player must stand to play. Assign points for successfully ringing the various objects:
• 10 points for either of the small tombstones
• 30 points for the skull tombstones
• 40 points for the RIP tombstone
• 50 points for either of the zombie hands alone
• 100 points for the tree monster top or arms
• Hit the gates at all, you lose all your points!
2
Tombstone Ring Toss
Bead Colors: CremeCheddarGreyDark GreyBlackWhiteZebra StripeSilver Pearl Stripe
Tree Monster: The main part of the tree monster is created on two square pegboards assembled as shown at right. Cut out these two patterns and tape them together in the same way.
Tombstone Ring Toss
6
Bead Colors: Dark BrownBlackMonkey Stripe
Tree Monster Trunk
Tombstone Ring Toss
7
Bead Colors: Dark BrownBlackMonkey Stripe
Tree Monster Base
Tombstone Ring Toss
8
Bead Colors: Dark BrownBlackMonkey Stripe
Tree Monster Arms
9
Tombstone Ring Toss
Rings: Using the same pattern, make 9 rings in the color combinations. The first color listed is for the outside, the second color is for the inside.
1. Place your pegboard on a flat, heat-safe surface.
2. Set a household iron to the medium setting. Place ironing paper over the pegboard. In a circular motion, begin to iron the project. Do not press down with the iron. As the beads begin to fuse, you will see circles of the beads start to show through the paper. When ironed properly, the beads will still have an open center. Let the design cool.
3. Remove the paper and bead design from the peg board. Flip the design over to expose the non-fused side. Repeat step two. Let cool completely.
NOTE: Beads need heat for about 10-20 seconds per side to fuse evenly. Lift the paper occasionally to see how the beads are fusing. Depending on the size of the project, additional heating time may be required. DO NOT OVER-IRON the beads as it will make the centers of the beads close and can make the assembly you do with your project more challenging.
Assemble the tombstones and gates by inserting the upright portion into the base. For the skull tombstone, also insert the candles into each base. For the small tombstones with the cross, insert the zombie hands into each base.
On the tree monster, glue each of the arms to the trunk as indicated by the pink dots on the diagram.