- 1 - RG-6 Coaxial Cable Preparation Tools Guide for the DXE-UT-KITF and DXE-UT-KITFQUAD Tool Kits DXE-UT-RG6-GUIDE Revision 0 DXE-UT-KITF DXE-UT-KITFQUAD DX Engineering 2019 1200 Southeast Ave., Tallmadge, OH 44278 USA Phone: (800) 777-0703 Technical Support and International: (330) 572-3200 Fax: (330) 572-3279 E-mail: [email protected]
12
Embed
RG-6 Prep guide · 2019-01-31 · Splicing Tape in place and stretch it out until the width of the tape is about 50%. D. While keeping the TES-2155 - 3M Temflex™ 2155 Rubber Splicing
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
- 1 -
RG-6 Coaxial Cable
Preparation Tools Guide
for the DXE-UT-KITF and
DXE-UT-KITFQUAD Tool Kits
DXE-UT-RG6-GUIDE Revision 0
DXE-UT-KITF DXE-UT-KITFQUAD
DX Engineering 2019
1200 Southeast Ave., Tallmadge, OH 44278 USA
Phone: (800) 777-0703 Technical Support and International: (330) 572-3200
The DX Engineering Snap-N-Seal® Connector Compression Tool does what ordinary pliers can't. This
ratchet compression tool installs your Snap-N-Seal® watertight connectors quickly and properly.
DXE-CPT-659 - DX Engineering CPT-659 Coaxial Cable Strippers DX Engineering CPT-659 Coaxial Cable Strippers are designed to prepare and strip CATV F6, RG-6, and
RG-59 coaxial cable. They are used preparing F6 coaxial cable for the installation of an F-Connector. Just
place the coaxial cable end into them and rotate around the cable until the cutting action is complete.
Their one-step cutting motion delivers a precision 1/4” - 1/4” cuts and will not nick, damage, or scratch
the conductor. Also included is one replacement blade.
DXE-CPT-659RB - DX Engineering Replacement Coaxial Cable Stripper Blades Is your coaxial cable stripper blade getting a little dull? Maybe it's time to get some DX Engineering
replacement coaxial cable stripper blades. These replacement coaxial cable stripper blades will bring your
DXE-CPT-659 cable prep tool back to peak performance.
- 11 -
DXE-CIT-1 - DX Engineering F-Connector Tightening Tool The DX Engineering F-Connector Tightening Tool makes easy work of reaching, loosening and tightening
your Type F coaxial connectors. With this tightening tool, you can install and remove F-connectors in tight
and hard-to-reach locations with minimal force, where regular wrenches won't fit. A "must-have" item for
CATV and satellite installers, it offers enough leverage to achieve a 30 in./lbs. of tightening force by hand
for better connections with less potential for problems. It also works with the coax curved in limited space
PTX-22058 - Permatex Dielectric Grease - 3 ounce Loctite and Permatex Dielectric Grease may be used in RF connectors to prevent moisture ingress. Feedlines and
connectors will last longer, providing peak performance for many more years with the use of
dielectric grease on the threads of RF connectors. Preventing the effects of moisture is critical
in RF feedline connections. Untreated connector threads will oxidize, corrode and seize more
quickly if water vapor can enter and collect inside RF connectors. Ultimately, moisture will
enter the coaxial cable, promoting contamination, resulting in elevated noise levels and
increased signal loss. Loctite or Permatex Dielectric Grease, placed into the air space of RF
connectors and their threads, will stop the adverse effects of water vapor and water ingress.
Avoiding direct application on mating surfaces of connector center pins, dielectric grease is
safe to use in the air spaces and threads of RF connectors.
TES-06132 - Scotch® Super 33+ Vinyl Electrical Tape Scotch® Super 33+ is highly conformable and super stretchy in all weather applications. This tape provides
flexibility and easy handling for all around performance. It combines PVC backing with excellent electrical
insulating properties to provide primary electrical insulation for splices up to 600V and protective jacketing.
Recommended as a protective overwrap for TES-2155 rubber splicing tape in RF connector
weatherproofing.
TES-2155 - Temflex™ 2155 Rubber Splicing Tape 3M Temflex™ 2155 Rubber Splicing Tape is a conformable self-fusing rubber electrical insulating tape. It is
designed for low voltage electrical insulating and moisture sealing applications. For outdoor use, it should be
protected from UV deterioration with an overwrap of TES-06132 Vinyl Electrical Tape.
- 12 -
Guide Updates
Every effort is made to supply the latest guide revision. Occasionally a guide will be updated
between the time your DX Engineering product is shipped and when you receive it. Please check
the DX Engineering web site (http://www.dxengineering.com) for the latest revision guide.
Technical Support
If you have questions about this product, or if you experience difficulties during the installation,
contact DX Engineering at (330) 572-3200. You can also e-mail us at: