REVERSIBLE PLATE COMPACTOR CRB11 – CRD12

22/05/2007 R08

REVERSIBLE PLATE COMPACTOR

CRB11 – CRD12

Model

_________________________

Serial Number

_________________________

Original Instructions May 2007 R08

batmatic CRB11 CRD12 22/05/2007 R08

- 2 -

FOREWORD We thank You to choose a BATMATIC plate compactor. Your new machine is an useful and safety job’s tool. Observing the safety regulations and the instructions in this book there will not be physical injury and the plate will be always in good condition. Worn-out machine parts are to be replaced as soon as possible. You will find the code numbers to order the spare parts in the chapter “Spare parts” in this instruction book.


- 3 -

TABLE OF CONTENTS SAFETY INSTRUCTIONS FOR PLATE COMPACTORS ........... ........................................4

SAFETY ...........................................................................................................................4

TRANSPORT AND LIFTING............................................................................................4

MAINTENANCE ...............................................................................................................5

PERIODIC MAINTENANCE.............................................................................................5

BATTERY.........................................................................................................................5

FIRE.................................................................................................................................5

RESIDUAL RISK..............................................................................................................5

CLIMBING ABILITY ................................... .........................................................................7

FUNCTION ..........................................................................................................................7

CHECKS BEFORE STARTING .......................................................................................8

ENGINE STARTING (MANUAL) ......................................................................................8

ENGINE STOPPING (MANUAL)......................................................................................8

ENGINE STARTING (ELECTRIC STARTER) .................................................................8

ENGINE STOPPING (ELECTRIC STARTER) .................................................................9

ENGINE OIL.....................................................................................................................9

AIR FILTER (DRY)...........................................................................................................9

AIR FILTER (OIL BATH) ..................................................................................................9

HYDRAULIC PUMP .......................................................................................................10

BATTERY CHARGING ..................................................................................................10

MAINTENANCE ........................................ ........................................................................11

TROUBLE, CAUSE, SOLUTION........................... ............................................................12

LUBRIFICANTS ....................................... .........................................................................13

ENGINE / EXCITER REVS................................................................................................13

TECHNICAL DATA CRB11............................... ................................................................14

TECHNICAL DATA CRD12............................... ................................................................15

SOUND MEASUREMENTS ...........................................................................................16

VIBRATION MEASUREMENTS.....................................................................................16

EXPLODED VIEWS ..........................................................................................................17

WARRANTY ........................................... ...........................................................................30

EC DECLARATION OF CONFORMITY....................... .....................................................31


- 4 -

SAFETY INSTRUCTIONS FOR PLATE COMPACTORS

SAFETY

• Plate compactors must only be operated by person who: ∗ is at least 18 years old; ∗ is physically and mentally fit for this job; ∗ may be expected to carry out the job he’s charged with carefully.

The employer must directly assign people who guide plate compactor. • Plate compactors must only be used for compaction jobs observing safety and operating

instructions. • People who work with plate compactors must know everything regarding safety

instructions. • Do not take drugs or drink alcohol before using plate compactors. • Always wear appropriate protective clothes (ear protections, gloves, protecting shoes and

helmet). • Do not alterate the operation devices of the plate compactor. • Do not leave control elements during compaction. • Store the compactor with engine off in a safe place. • Always refill fuel tank when the engine is off. Do not allow fuel to come into contact with the

hot parts of compactor and engine. • Do not smoke when using compactor. Keep the compactor out of open flames. • Always check fuel tank cap. If there is a fuel cock, shut it off when the engine is not

working. WARNING

If fuel tank leaks, replace it immediately: A fuel tank in bad conditions could explode

• Do not use the compactor in places where there are gaseous exhalations. • Do not use the machine indoors or in an enclosed area unless inadequate ventilation. • Always wear appropriate protective clothes. • When the work area is near slopes, the compactor could turn over. • When you use compactor in reverse and in a narrow place, the operator must be sideways

from the handle in order to avoid stumbling. • Always operate in safe conditions in order to avoid accidents. • Always operate in maximum stability conditions. • Use transport wheels only for movements in yard. In all the other situations they must be

removed. • Always make sure of the proper functioning of the safety and control devices. • If there are any problems, stop immediately the machine and inform the person responsible

of the yard. TRANSPORT AND LIFTING

• Do not lift the compactor when is running. • Check that lifting points are not damaged. • For loading and unloading the compactor, appropriate lifting-gear are necessary which

have to be used on the lifting points. • Be sure that the ramps are fixed and check the tolerable weight in order to avoid turnovers. • Do not transport compactors when engine is running. • Tie the machine on vehicle to prevent sliding or tipping over.


- 5 -

• For long transports, empty completely the fuel tank and close it. WARNING

Do not lift or hook the plate compactor by the handle. MAINTENANCE

• Use original spare parts only. • Do not alterate the operation devices of plate compactor. • Do not alterate RPM of the engine. • Do not turn the engine on without air filter.

WARNING

Modifications in this machine are subject to the express approval of BATMATIC which in case of non observance will refuse all liabilities and all warranties

• Do not make maintenance operations when machine is running or when engine is on. • As soon as maintenance and repair jobs have been completed, all safety devices have to

be properly reinstalled. PERIODIC MAINTENANCE

Regular maintenance is required for a good performance of the compactor. BATTERY

Batteries contain toxic and corrosive acids. Avoid getting acid on your skin and clothes. If you get acid on your eyes, rinse them with water and seek immediately medical treatment. WARNING

When changing batteries, always be careful not to short circuit the battery termionals

FIRE

In the case of a fire in the machine, if possible use an AB class powder extinguisher. RESIDUAL RISK

Plate compactors are designed for absorbing a large part of machine vibrations. Depending on the operation, the ground conditions and exposure time, the recommended limits for hand-arm vibrations may be exceeded.


- 6 -

WARNING

Do not use the machine on grounds already compacted

Long exposure to vibrations can damage the hands and wrists. Do not use the machine if you experience discomfort, cramp or pain and consult a doctor before restart working with the machine. Long exposure to loud noise without ear protector can cause permanent damage to hearing.

Please also observe regulations valid in Your yard.


- 7 -

CLIMBING ABILITY

FUNCTION

The vibration required for tamping is produced by the exciter which is on the compacting plate. The engine starts the exciter and the torque is transmitted by the centrifugal clutch and by the belt. In order to allow the idling of the drive engine, the centrifugal clutch, at low engine speeds, interrupts the flow of power to exciter. The compactor must always be used with the gas handle in the “OPERATIVE” position. The engine support and the compacting plates are connected by 4 shockmount, which are mounted to avoid that vibrations reach the operator. Plate compactor is equipped with hydraulic system that allow to change gradually the speed. The direction of plate compactor depends on the position of control levers on the handle.


- 8 -

APPLICATIONS The compactor CR11/12 is ideal for interlocking tiles floor laying, asphalt restoration, tamping of digging, soil, trench and road maintenance. OPERATION CHECKS BEFORE STARTING

• Before start using compactor, carefully read instruction manual. • Engine oil level

Check oil level using the proper dipstick. If necessary refill with SAE 15 W 40 oil.

• Air filter Check that air filter is clean and in good condition. If necessary clean or replace it.

• Fuel Never use oil/gasoline mixture or dirty fuel. Avoid getting dirt, dust or water into fuel tank. Refuel avoiding leaks on engine. ENGINE STARTING (MANUAL)

• Open the fuel valve. • Move the throttle lever to 3/4 position. • Turn the choke lever (if present). • Turn the engine switch on the ON position. • Pull the starter grip lightly until resistance is felt, then pull briskly.

WARNING Pull hand crank until it starts, in order to avoid counterblows

• As the engine warms up, gradually move the choke lever (if present). • Warm up the engine at the minimum speed for some minutes. • The compactor will start moving when the throttle lever is in operative position.

ENGINE STOPPING (MANUAL)

• Move the throttle lever to the minimum position. Warm up the engine at the minimum speed for some minutes.

• Turn the engine switch on the OFF position. WARNING Never operate the engine switch when the engine is at the maximum speed.

• Turn the fuel valve on the OFF position. ENGINE STARTING (ELECTRIC STARTER)

• Insert the key into the dashboard. • Turn the key on the ON position and after on the START position until the engine starts.


- 9 -

ENGINE STOPPING (ELECTRIC STARTER)

• Move the throttle lever to the minimum position. Let the engine turn at the minimum speed for some minutes.

• Turn the key on the OFF position. • Release the key when engine starts

WARNING

Never operate the engine switch when the engine is at the maximum speed.

• Turn the fuel valve to the OFF position. ENGINE OIL

• Check oil level using the proper dipstick, if necessary refill with SAE 15 W 40 oil. Oil change

• Drain oil at warm engine. • Refill with SAE 15W40 oil.

WARNING Only use oil with characteristics advised to the manufacturer engine (see

engine book). AIR FILTER (DRY)

WARNING Regularly clean the air filter in order to avoid carburettor damages especially

when operating in dusty areas.

• Open air cleaner and remove element. • Lightly and repeatedly tap the element on a hard surface to eliminate all excess dirt. • Clean the element. • Refit the air filter. Do not run the engine without the air filter.

AIR FILTER (OIL BATH)

WARNING Regularly clean the air filter in order to avoid carburettor damages especially

when operating in dusty areas.

• Open air cleaner and remove upper element. • Wash the upper filtering element with soap and water. • Clean the upper bowl. • Remount the upper filtering element. • Remove the lower filtering element. • Clean and dry filtering element. • Drain and clean bowl.


- 10 -

• Fill with engine oil up to level mark. • Reassemble air cleaner.

WARNING Never use gasoline or low flash point solvents for cleaning the air filter to

avoid fire and explosions. HYDRAULIC PUMP

• Put the handle on vertical position. • Open the pump cover. • Check oil level, refill if it is necessary. • Refill until the level with hydraulic oil (See lubrificants table). • Close the pump cover.

BATTERY CHARGING

• Use a max 14,4 V voltage battery charger to charge the battery. Do not disperse oil, batteries, fuel and dangerous substances in the

ambient, as they have high pollution power.


- 11 -

MAINTENANCE

PARTS MAINTENANCE INTERVAL Air filter Fuel tank Engine Engine Exciter

Check filter, clean or replace if it is necessary Check filter oil level (only oil bath models) Check fuel tank and fuel cap lid. If necessary replace. Check oil level, refill if it is necessary Check engine RPM Check exciter lid

daily

Engine

First oil change

After 20 h

Engine

Clean spark plug

Monthly

V-Belt

Check V-belt tension

Monthly

Fuel Tank Engine

Check fuel filter, replace if necessary Oil change

After 100 h

Exciter

Check oil level, refill if necessary

After 150 h

Exciter

Oil change

After 250 h


- 12 -

TROUBLE, CAUSE, SOLUTION

TROUBLE POSSIBLE CAUSE SOLUTION

Reduced speed or not forward motion

Low oil level. Check the oil level in the hydraulic pump

located in the handle

Top the oil until the level. Move the command lever for several times (this operation

helps blowing the air out from the oil circuit)

The machine goes only backward

The lip packing is broken or weared Replace the lip packing

There’s too much oil in the hydraulic pump located on

the handle

Fill out the oil in excess and restore the level Low backward speed or not

speed at all There’s some air under pressure in the pump

Open the pump’s cap to blow the exceeding air out

The oil pipe leaks Replace the leaking parts

The pump oil level decreases during the time

The seal of vibrating cylinder is broken or weared and spilling the oil inside the

vibrator

Replace the seal and top up the oil level (pump and

exciter)

The transmission belt is broken

The wear and tear has caused the belt to loosen up

Replace the belt The engine’s revs are regular but the machine

does not vibrate The centrifugal clutch has

broken Repair or replace the

centrifugal clutch The engine’s revs are low

but the exciter does not stop The centrifugal clutch has

broken Repair or replace the

centrifugal clutch Verify that during

compaction gas lever is at the max position Reduced or irregular speed The engine revs are not

correct Reset the engine revs with

proper instrument Open the exciter and

remove the cause of failure The engine works and the exciter makes vibration but

the machine doesn’t work or work in irregular way

Mechanical failure or dismissing of eccentrical

weight Contact immediately Batmatic or any other

authorized centre Open the exciter and

replace the weared and teared parts The engine does not work

properly, the clutch makes smoke, the vibrator strains

The mechanicals parts of vibrators do not work properly (bearings are

weared and teared, lack of oil, gears are broken)

Contact immediately Batmatic or any other

authorized centre

Fuel tank empty Add fuel

Oil lack Add oil

Dirty air filter Clean air filter if necessary replace it

The engine turns off or does not work properly

Engine damaged Contact an engine service center


- 13 -

LUBRIFICANTS

Model Quantity Type

CR 11-12 0,30 kg

CR 15-20 0,40 kg Exciter

CR 25-40 0,80 kg

Pontonic FDL 75W90

CR 11-12 1,00 kg

CR 15-20 1,30 kg Hydraulic System

CR 25-40 0,30 kg

T68

Engine All models See engine instructions

SAE 15W40

ENGINE / EXCITER REVS

Model Engine Exciter

CR 11-12 3400 – 3450 5350 – 5400

CR 15-20 3550 – 3600 5350 – 5400

CR 25 (3000 – 3300)* 4150 – 4200

CR 40 (3000 – 3300)* 4150 – 4200

For CR25 and CR40 models Engine revs are a approximate value. Please refer to Exciter revs.

WARNING Set the rpm as per the above table. A different rpm will not make the compactor working properly and could broke it. If the set rpm is changed, the warranty will not be recognized.


- 14 -

TECHNICAL DATA CRB11

Item

CRBH11

CRBH11-L

CRBR11

CRBR11-L

Dimensions base plate (Width x Length)

400 x 632 mm

500 x 632 mm

400 x 632 mm

500 x 632 mm

Operating weight 112 kg 121 kg 112 kg 121 kg

Working speed 25-30 m/min

Max climbing ability 20%

Frequency 90 Hz

Centrifugal force 21 kN

Transmission Centrifugal clutch / Belt

Air-cooled single-cylinder 4 stroke

Engine Honda GX 160

Robin Subaru EX 17

Engine Power kW (HP) 3,6 (4,8)

kW (HP) 4,2 (5,7)

Displacement 163 cm3 169 cm3

Fuel Petrol

Fuel consumption l/h 1,2 l/h 1,2

Fuel tank capacity l 3,6 l 3,6


- 15 -

TECHNICAL DATA CRD12

Item

CRDH12

CRDH12-L

CRDL12

CRDL12-L

Dimensions base plate (Width x Length)

400 x 632 mm

500 x 632 mm

400 x 632 mm

500 x 632 mm

Operating weight 120 kg 129 kg 120 kg 129 kg

Working speed 25-30 m/min

Max climbing ability 20%

Frequency 90 Hz

Centrifugal force 21 kN

Transmission Centrifugal clutch / Belt

Air-cooled single-cylinder 4 stroke

Engine Hatz

1 B20 Lombardini 15 LD 225

Engine Power kW (HP) 3,7 (5,0)

kW (HP) 3,5 (4,7)

Displacement 232 cm3 224 cm3

Fuel Diesel

Fuel consumption l/h 1,1 l/h 1,1

Fuel tank capacity l 2,5 l 3,0


- 16 -

SOUND MEASUREMENTS The product has been produced in accordance with the standard 2000/14/CE, procedure I annex VI. Measured sound power level 106 [dB(A)] and guaranteed sound power level 108 [dB(A)] on a significant equipment. VIBRATION MEASUREMENTS

Products are tested for hand/arm vibration level in accordance with annex D prEN500-4:2001 The hand/harm vibration level is 12 m/s2 The plate compactor has been tested on a “macadam” surface, produced with not cleaned stone crusher grit, with 16 mm medium diameter (with components which have diameter that goes from 10 to 20 mm).


- 17 -

EXPLODED VIEWS

CENTRIFUGAL CLUTCH

POS ITEM COD CRB11 CRD12

10 HOUSING 1

20 BALL BEARING 1

30 SEEGER CIRCLIP RING 1


50 CYLINDRIC HUB 1

50 CONIC HUB 1

60 CENTRIFUGAL FLY WEIGHT 2

70 CLUTCH LINING 2

80 SPRING 151994

4

90 COVER DISK 2


110 PULLEY 1

120 PARALLEL PINS 3

130 CENTRIFUGAL FLY WEIGHT 3

140 COVER PLATE 1



- 18 -

EXCITER


- 19 -

EXCITER

POS ITEM COD CRB11 – CRD12

1 PISTON 530051 1

2 CONDUCTED GEAR CR11-20 530039 1

3 BEARING NJ 208 M C4 151969 4

4 SCREW TCEI M 5x 12 8.8 UNI 5931 151299 1

5 ECCENTRIC WEIGHT CR11-12 530177 4

6 BALL BEARING 16008 151078 1

7 WASHER M 5 UNI 6592 151197 1

8 SCREW TCEI M12x 30 12.9 UNI 5931 151307 4

9 LIP PACKING NA 25x 17x 5,5 VITON 131093 1

10 EXCITER COVER CR11-20 530054 1

12 BALL BEARING 608 ZZ 151079 2

13 EXCITER COVER CR11-20 530055 2

14 INDEXING BOLT D.18 L.105 CR11-12 530904 1

15 SCREW TCEI M 6x 16 8.8 UNI 5931 ZN 151301 16

16 WASHER M 6 UNI 6592 ZN 151198 8

17 SCREW 530056 1

18 TRIPPING PIN 6325 8x50 RETT. 152199 1

19 CLUTCH WASHER. 45X10.5 SP.6 ZN 530612 1

20 EXCITER CLUTCH CR11 CON 530749 1

21 CONTACT WASHER 10(10.2x22x1.6)ZN 151814 1

22 RUBBER GAGE D.120 SP.10 530144 1

23 EXCITER HOUSING CR11/12 530165 1

24 SEEGER I. 22 UNI 7437 151222 1

25 NIPPLE 1/4" 151137 1

26 CONDUCTED SHAFT CR11-12 530169 1

27 SEEGER E. 40 DIN 471 152043 6

28 COPPER WASHER 1/4" 151209 1

29 CONDUCTOR SHAFT CR11-12 530902 1

30 DOUBLE LIP SEAL 40x62x7 131760 1

31 EXCITER CYLINDER CR11-20 530050 1

32 CONDUCTOR GEAR CR11-20 530903 1


- 20 -

BASE PLATE


- 21 -

BASE PLATE

POS ITEM COD CRBH11 CRBR11 CRDH12

CRDL12

1 LOCKNUT M12 DIN 982 151084 4 4

2 SHOCKMOUNT SUPPORT CR11-20 530615 4 4

3 SCREW TCEI M12x 75 10.9 UNI 5931 151953 2 2

4 SCREW TCEI M12x130 10.9 UNI 5931 151954 6 6

5 SCREW TE M12x25 10.9 UNI 5739 152256 8 8

6 WASHER M12 UNI 6592 ZN 151201 8 8

7 CAP TCEI 1/4" G 152181 1 1

8 ENGINE SUPPORT CR11-12 HO-HA 530194 1

8 ENGINE SUPPORT CR 11-12 Y-L 530196 1

9 BASE PLATE L 500 CR11-12 530613 1 1

9 BASE PLATE L 400 CR11-12 530614 1 1

10 EXCITER CR11-12 530185 1 1

11 SHOCKMOUNT MF D 60x50 M12x40 45-50 SH

131013 4 4

12 WASHER M12 UNI 6592 ZN 151201 4 4


- 22 -

PUMP


- 23 -

PUMP

POS ITEM COD CRB11 – CRD12

1 SCREW TE M 6x12 8.8 UNI 5739 ZN 152194 4

2 PUMP COVER CR11-20 530693 1

3 OR 3156 131141 2

4 PUMP HOUSING BARE 530593 1

5 SCREW TCEI M 6x 10 8.8 UNI 5931 ZN 152198 1

6 GEAR RACK AXLE GUIDE (OIL LEVEL) 530655 1

7 PINION CR11-20 530498 1

8 OR 4150 132131 2

9 OR 4081 (20,22x3,53) 131142 2

10 FLANGE CR11-20 530123 2

11 CONTROL HANDLE 530130 2

12 SCREW TCEI M10x 25 8.8 UNI 5931 ZN 151831 2

13 GEAR RACK AXLE CR11-20 530643 1

14 LIP PACKING SIMKO 300 - 32x24,5x3 132258 1

15 FLANGE CR11-20 530646 1

16 FLANGE CR11-20 530644 1

17 SPRING PR F.3-30-50 VDSiCr 530125 1

18 FLANGE CR11-12 530691 1

19 SCREW 530647 1


- 24 -

HANDLE


- 25 -

HANDLE

POS DESCRIZIONE COD CRB11 CRD12

2 SHEATH (cm 114+reg. M10x1+reg. M6) 530884 1 1

3 WIRE D1,9 ACC. ZINC. L= 2000 mm 151793 1 1

4 NUT M10 UNI 5588 ZN 151085 1 1

5 HANDLE CRB 11 530686 1

5 HANDLE CRD12 530731 1

6 SHOCKMOUNT MF D 50x40 M10x30 60 SH 131784 1 1

7 COPPER WASHER 1/4" 151209 1 1

8 PLASTIC CAP D25 131244 2 2

9 NIPPLE 1/4" 151137 1 1

10 SCREW TCEI M 8x 25 8.8 UNI 5931 ZN 152138 4 4

11 GAS HANDLE 22.1 151978 1 1

12 HANDLE GRIP 131174 1 1

13 WASHER M12 UNI 6592 ZN 152006 1 1

14 SPRING PR F.2/22/33 TDM C.85 530017 1 1

15 RETENTION BOLT PIN 530003 1 1

16 HYDRAULIC PIPE 1/4 R1 MT 0,375 512 FP 1183 512 FP 1183 131295 1 1


- 26 -

VIBRATORY PLATE


- 27 -

VIBRATORY PLATE

POS ITEM COD CRBH11 CRBR11 CRDH12 CRDL12

1 SCREW TE 5/16-24x3/4" 8.8 UNF 151309 4

1 SCREW TE M 8x16 8.8 UNI 5739 ZN 151310 5 6

2 SCREW TCEI M12x 65 8.8 UNI 5931 ZN 152200 2 2 2

4 ROLLBAR CRBH11 530418 1

4 ROLLBAR CRDH12 530437 1

4 ROLLBAR CRDL12 530497 1

5 ROLLBAR CLAMP 530493 1 1 1

6 CONTACT WASHER 12(12.4x27x1.8)ZN 151813 4 4 4

7 V BELT HFX SEZ. XPA 782 131788 1

7 V BELT HFX SEZ. XPA 832 132055 1 1

8 SCREW TE M10x40 8.8 UNI 5739 ZN 151333 4

8 SCREW TE M 8x30 8.8 UNI 5739 ZN 152105 4

8 SCREW TE M 8x40 8.8 UNI 5737 ZN 152191 4


10 CONTACT WASHER 10(10.2x22x1.6) 151791 4

10 CONTACT WASHER 8(8.2x18x1.4)ZN 151807 4 4



13 SCREW TE M 8x50 8.8 UNI 5737 152197 1 1

13 SCREW TE 5/16-24x3/4" 8.8 UNF 151309 1




- 28 -

VIBRATORY PLATE


- 29 -

VIBRATORY PLATE

POS ITEM COD CRBH11 CRBR11 CRDH12 CRDL12

16 GROWER WASHER M10 UNI 1751 152000 4 4 4

17 WASHER M 8x32 ZN 152192 1

17 CLUTCH WASHER. 28X8.5 SP.5 ZN 560267 1 1

18 SCREW TCEI M 6x 16 8.8 UNI 5931 ZN 151301 4 4 4

19 COLLAR CP2 D20 131033 2 2 2

20 CLUTCH THICKNESS 560502 1

21 WASHER M 6 UNI 6592 ZN 151198 4 4 4

22 CENTRIFUGAL CLUTCH 090-2594 152229 1

22 CENTRIFUGAL CLUTCH 090-2561 152228 1 1

23 WASHER M18 UNI 6592 ZN 152049 1

24 ENGINE PROTECTION CRD12 530425 1 1

24 ENGINE PROTECTION CRBH11 530429 1

25 BELT PROTECTION HOLDER 530423 1 1

25 BELT PROTECTION HOLDER 530427 1

26 V-BELT PROTECTION CR11 530743 1 1 1

27 ROBIN EX 17OD50060 ENGINE 182217 1

27 HONDA GX 160 K1 QX4 ENGINE 181129 1

27 HATZ 1B20 ENGINE 181130 1

27 LOMBARDINI 15LD225 ENGINE 181696 1

29 SCREW TE M 8x30 8.8 UNI 5739 ZN 152105 4 4 4

30 WASHER M 8x24 ZN 152006 4 4 4


- 30 -

WARRANTY Your new BATMATIC Plate Compactor is warranted to the original purchaser for a period of one year (12 months) from the original date of purchase. The BATMATIC warranty is against defects in design, materials and workmanship. The following are not covered under the BATMATIC warranty: 1. Damage caused by abuse, misuse, dropping or other similar damage caused by or as a result

of failure to follow assembly, operation or user maintenance instructions. 2. Alterations, additions or repairs carried out by persons other than BATMATIC or their

recognized agents. 3. Transportation or shipment costs to and from BATMATIC or their recognized agents, for repair

or assessment against a warranty claim, on any machine. 4. Materials and/or labor costs to renew, repair or replace components due to fair wear and tear. 5. Engine BATMATIC and/or their recognized agents, directors, employees or insurers will not be held liable for consequential or other damages, losses or expenses in connection with or by reason of or the inability to use the machine for any purpose. Warranty Claims All warranty claims should firstly be directed to the local dealer, either by telephone, by fax, by email, or in writing. USE ONLY GENUINE BATMATIC PARTS AND ACCESSORIES For your own safety, the safety of others and the life of your machine


- 31 -

batmatic

EC DECLARATION OF CONFORMITY WE

Batmatic srl Via romitaggio 31 43010 Bianconese di Fontevivo (Parma) - Italia

HOLDER OF TECHNICAL DOCUMENTATION SHOWED

DECLARE UNDER OUR SOLE RESPONSIBILITY THAT THE PRODUCT

Type Reversible Plate Compactor

Model ( ) CRBH11 ( ) CRBR11

Net installed power kW 3,6 kW 4,2

Model ( ) CRDH12 ( ) CRDL12

Net installed power kW 3,7 kW 3,5

Serial number

Brand Batmatic

Applications Interlocking tiles floor and asphalt restoration

Measured sound power level 106 [dB(A)]

Guaranteed sound power level 108 [dB(A)]

HAS BEEN PRODUCED IN ACCORDANCE WITH THE STANDARD 2000/14/CE, PROCEDURE I ANNEX VI

AND HAS BEEN PRODUCED IN ACCORDANCE WITH THE FOLLOWING STANDARDS:

2006/42/CE EN 500-1 EN 500-4 E AUTORIZZIAMO AND WE AUTHORIZE Saj Ferrante Batmatic srl Via romitaggio 31 43010 Bianconese di Fontevivo (PR) TO SERVE THE TECHNICAL DOCUMENTATION Bianconese, li ...........................................

22/05/2007 R08

batmatic BATMATIC SRL

Via Romitaggio, 31 43010 Bianconese di Fontevivo (PR) - ITALIA Tel.: +39 0521 619298 - Fax: +39 0521 619682

E – mail: [email protected] www.batmatic.com

REVERSIBLE PLATE COMPACTOR CRB11 – CRD12

Documents