Removal and Installation

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATIONA-Pillar Trim Panel

Item Part Number Description Item Part Number Description4 519A58 Overhead console1 N806664 Sun visor screws/sun visor

arm clip screws (6 required) 5 Overhead console electricalconnector (part of 14A464)2 04132 Sun visor arm clips (2

required) 6 030A64 A-pillar trim panel (2required) (RH/LH)3 4104/4105 Sun visors (2 required)

(RH/LH) 7 51916 Header trim panel(Continued)

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

501-05-2 501-05-2Interior Trim and OrnamentationREMOVAL AND INSTALLATION (Continued)Removal and Installation 3. If necessary, remove the overhead console.

Disconnect the electrical connector.NOTE: If removing the header trim panel, removethe 2 A-pillar trim panels. 4. If necessary, remove the 2 screws and the 2 sun

visor arm clips.1. Remove the 2 sun visor srews and the sun

visor. 5. If necessary, remove the header trim panel.

2. Remove the A-pillar trim panel. 6. To install, reverse the removal procedure.

2007 Mustang, Mustang GT 8/2006

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATIONDoor Trim Panel

Removal and InstallationItem Part Number Description1 17D698/17D699 Sail panel (RH/LH)

1. Remove the sail panel.2 21999 Door lock control knob bezel(RH/LH) If equipped, disconnect the exterior mirror

control switch electrical connector.3 22620/22621 Interior door handle cover(RH/LH)

2. Remove the interior door handle cover and the4 N807780 Door trim panel boltdoor trim panel bolt.5 14527/14528 Window control switch

housing (RH/LH)3. Remove the window control switch housing.6 Window control switch

electrical connector Disconnect the electrical connector.7 W709996 Door trim panel screw

4. Remove the door trim panel center screw.8 6320456/ Door trim panel handle cover6320457 (RH/LH)

5. Remove the door trim panel handle cover and9 N807780 Door trim panel boltthe door trim panel bolt.

10 W709996 Door trim panel screws (8required)

11 23942/23943 Door trim panel (RH/LH)

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

501-05-2 501-05-2Interior Trim and OrnamentationREMOVAL AND INSTALLATION (Continued)6. Remove the 8 outer door trim panel screws and 7. To install, reverse the removal procedure.

the door trim panel. Disconnect the interior door handle actuating

cable. If equipped, disconnect the subwoofer

electrical connector.

2007 Mustang, Mustang GT 8/2006

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATIONHeadliner

2. Remove the 6 sun visor screws, the 2 sunItem Part Number Descriptionvisors, and the 2 sun visor arm clips.1 N806664 Sun visor screws/sun visor

arm clip screws (6 required)3. Remove the overhead console.2 6304104/ Sun visors (2 required)

6304105 (RH/LH) Disconnect the electrical connector.3 6304132 Sun visor arm clips (2

4. Remove the 2 headliner pin-type retainers.required)4 519A58 Overhead console

5. Disconnect the headliner electrical connector5 Overhead console electricaland remove the headliner.connector (part of 14A464)

6 Headliner electrical connector(part of 14484)

7 W709950 Headliner pin-type retainers(2 required)

8 6351916 Headliner

Removal and Installation

1. Remove the quarter window trim panel. Foradditional information, refer to Quarter WindowTrim Panel in this section.

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

501-05-2 501-05-2Interior Trim and OrnamentationREMOVAL AND INSTALLATION (Continued)6. NOTE: A new headliner will need to be

installed if the headliner is folded duringremoval or installation.To install, reverse the removal procedure.

2007 Mustang, Mustang GT 8/2006

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATIONInterior Trim Exploded ViewNOTE: The coupe is shown, the convertible is similar.

Item Part Number Description Item Part Number Description9 6311B08 Front safety belt assembly1 03598/03599 A-pillar trim panel (RH/LH)

10 W505956 Coat hook bolt2 13208/13209 Door scuff plate (RH/LH)11 29024 Coat hook3 390018 A-pillar lower trim panel

pin-type retainer 12 51986/51987 Quarter window trim panel(RH/LH)4 02344/02345 A-pillar lower trim panel

(RH/LH) 13 W706544 Quarter trim panel pin-typeretainer (3 required)5 Lower front safety belt

anchor bolt cover (part of 14 31012/31013 Quarter trim panel (RH/LH)6311B08-A)

15 54403 Parcel shelf pin-type retainers6 Lower front safety belt (4 required)

anchor bolt (part of16 6346668 Parcel shelf6311B08-A)

7 Upper front safety belt anchor1. For additional information, refer to thebolt cover (part of

6311B08-A) procedures in this section.8 Upper front safety belt anchor

bolt (part of 6311B08-A)(Continued)

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATIONParcel Shelf

Removal and Installation

1. Remove the quarter window trim panel. Foradditional information, refer to Quarter WindowTrim Panel in this section.

2. Remove the 4 parcel shelf pin-type retainers.

3. Position the 2 rear seat belts aside and removethe parcel shelf.

4. To install, reverse the removal procedure.

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATIONQuarter Trim Panel Convertible

Item Part Number Description Item Part Number Description5 31012/31013 Lower quarter trim panel1 13208/13209 Door scuff plate (RH/LH)

(RH/LH)2 31004/31005 Upper quarter trim panel cap(RH/LH)

Removal and Installation3 390018 Quarter trim panel pin-typeretainers (3 required)

1. Remove the door scuff plate.4 31112/31113 Upper quarter trim panel(RH/LH)

2. Remove the upper quarter trim panel cap.(Continued)

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

501-05-2 501-05-2Interior Trim and OrnamentationREMOVAL AND INSTALLATION (Continued)3. Remove the rear seat cushion. For additional 5. Remove the 2 pin-type retainers and the lower

information, refer to Section 501-10. quarter trim panel.

4. Remove the pin-type retainer and the upper 6. To install, reverse the removal procedure.quarter trim panel.

2007 Mustang, Mustang GT 8/2006

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATIONQuarter Trim Panel Coupe

Removal and Installation

1. Remove the door scuff plate.

2. Remove the quarter trim panel lower pin-typeretainer.

3. Fold the rear seat forward, remove the 2pin-type retainers, and the rear quarter trimpanel.

4. To install, reverse the removal procedure.

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

501-05-1 501-05-1Interior Trim and Ornamentation

REMOVAL AND INSTALLATION3. Open the coat hook cover. Remove the bolt andQuarter Window Trim Panel

coat hook.Removal and Installation

4. Remove the upper front safety belt anchor boltcover and bolt.

1. NOTE: On the coupe, install the front locating To install, tighten to 48 Nm (35 lb-ft).hook, then snap the A-pillar trim panel in place

working rearward.5. Remove the quarter window trim panel.

Remove the 2 A-pillar trim panels.6. To install, reverse the removal procedure.

2. Remove the rear quarter trim panel. Foradditional information, refer to Quarter TrimPanel Coupe in this section.

Copyright 2006, Ford Motor CompanyLast updated: 6/19/2006 2007 Mustang, Mustang GT 8/2006

A-Pillar Trim Panel2345789