Registers and Counters Chapter 6. Registers and Counters A register is a group of flip-flops Each flip-flop stores one bit of info A counter is a register.

Registers and Counters

Chapter 6

Registers and Counters

• A register is a group of flip-flops• Each flip-flop stores one bit of info• A counter is a register that goes through a

predetermined sequence of binary states

Registers4-bit register with • D Flip-flops• Common clock input• Common clear input; when Clear=0

flip-flops reset asynchronous

Register with parallel loadExercise: Explain how this register works. Why is it necessary to feed back to the combinational input circuit? What if this was not done?

Shift Registers

What happens with every clock pulse?

Serial transfer

Serial additionExercise: Describe how you add two binary numbers by hand. How do you apply this to design a serial adder?Assume you have two n-bit shift registers. Design a circuit that adds one bit at a time and stores the result in one of the shift registers. How do you handle the carries?Hint: you may need one additional flip-flop. Indicate the clock connections of the shift registers and the flip-flop.

Serial adder

Serial adder

Serial adder

Exercise: Explain how this circuit works. Obtain the excitation/input equations for the JK Flip-flop and the equation for the sum .Run an example sum assuming the circuit uses two 3-bit shift registers.

𝐽𝑄=𝑥𝑦

𝐾𝑄=𝑥 ′ 𝑦 ′=(𝑥+𝑦) ′

𝑆=𝑥⨁ 𝑦⊕𝑄

Universal shift register

1. Clear control to clear register to 02. Clock input to synchronize operations3. Shift-right control to enable operation and associated

input and output lines4. Shift-left control to enable operation and associated input

and output lines5. Parallel-load control to enable parallel transfer and the n

input lines6. n parallel output lines7. Control state to leave information in the register

unchanged

Universal shift register

Exercise: explain how this universal shift register works

Universal shift register

Universal shift register

Counters

• A counter is a register that goes through a prescribed sequence of states upon the application of input pulses

• Two types of counters– Ripple counters– Synchronous counters

Ripple Counters4-bit ripple binary counter with T Flip-flops

Exercise: Obtain the state table.

Ripple counters4-bit binary ripple counter with D flip-flops

Exercise: Explain how this counter works.

Ripple Counters

BCD ripple counter

State diagram of a decimal BCD counterr

BCD ripple counterExercise: Obtain the excitation equation and the state table. Explain how this counter works.

Three-decade decimal BCD counter

Synchronous Counters

• Simple design procedure• Least significant digit Flip-flop is

complemented with every clock pulse• A flip-flop in any other position is

complemented when all the bits in the lower significant positions are equal to 1

Synchronous CountersExercise: Using the excitation tables for the JK flip-flops explain how this counter works.

Up-down binary counter

Countdown binary counter:• Least significant bit is complemented with

each clock pulse• A bit in any other position is

complemented is all lower significant bits are all equal to 0

BCD counter

𝑇 𝑄1=1𝑇 𝑄2=𝑄 ′ 8𝑄1

𝑇 𝑄4=𝑄2𝑄1

𝑇 𝑄8=𝑄8𝑄1+𝑄4𝑄2𝑄1

𝑦=𝑄8𝑄1

Flip-flop input equations are simplified using maps

Binary counter with parallel loadExercise: Explain how this counter works:• When Load is high/low;• When Clear is high/low; • When Count is high/low;• How should Load and

Clear be for counting?

Binary counter with parallel load

BCD counter implemented with counter with parallel load

Other CountersCounter with unused states

Other CountersCounter with unused states

Ring counter

Johnson counter

Connecting complemented LSB to ring counter input doubles the number of states of ring counter.

What happens if counter starts from an unused state?

Homework Assignment

• 6.4• 6.6• 6.9 (a)• 6.18• 6.21• 6.23• 6.26