This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Engine fundamentals and performance metrics, computer modeling supportedby in-depth understanding of fundamental engine processes and detailedexperiments in engine design optimization.
Day 1 (Engine fundamentals)Hour 1: IC Engine Review, 0, 1 and 3-D modelingHour 2: Turbochargers, Engine Performance MetricsHour 3: Chemical Kinetics, HCCI & SI Combustion
Day 2 (Spray combustion modeling)Hour 4: Atomization, Drop Breakup/CoalescenceHour 5: Drop Drag/Wall Impinge/VaporizationHour 6: Heat transfer, NOx and Soot Emissions
Day 3 (Applications)Hour 7: Diesel combustion and SI knock modelingHour 8: Optimization and Low Temperature CombustionHour 9: Automotive applications and the Future
Turbocharging
3 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Improved
Turbocharging
Purpose of turbocharging or supercharging is to increase inlet air density,- increase amount of air in the cylinder.
Mechanical supercharging- driven directly by power from engine.
Turbocharger - connected compressor/turbine- energy in exhaust used to drive turbine.
Supercharging necessary in two-strokesfor effective scavenging:
- intake P > exhaust P- crankcase used as a pump
Some engines combine engine-driven andmechanical (e.g., in two-stage configuration).
Intercooler after compressor- controls combustion air temperature.
4 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Turbocharging
Energy in exhaust is used to driveturbine which drives compressor
Wastegate used to by-pass turbine
Charge air cooling after compressorfurther increases air density- more air for combustion
5 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Regulated Two-Stage Turbocharger
Duplicated Configuration per Cylinder Bank
EGR Cooler
EGR Cooler
EGR Valve
EGR Valve
LP stage Turbo-Chargerwith Bypass
LP stage Turbo-Chargerwith Bypass
HP stage Turbocharger
HP stage Turbocharger
Regulating valve
Regulating valveCharge AirCooler
Charge AirCooler
CompressorBypass
CompressorBypass
LP TURBINE
Regulating Valve
LP Stage Bypass
HP TURBINE Compressor Bypass
GT-Power R2S Turbo Circuit
6 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Variable Valve Timing - IVC control
ln V
Q
ln T
ln V
TDC IVC
T ign
Q
Reduced Peak Temp (NOx)Improved phasing
IVC
IVC
VPP V
Isentropic
( 1)IVC
IVC
VTT V
Boost explains 20% of the improved fuel efficiency of diesel vs. SI
ln P
TDC IVC
Pressure/time ofignition
Boost
Compressor
7 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Centrifugal compressor typically used inautomotive applications
Provides high mass flow rate atrelatively low pressure ratio ~ 3.5
Rotates at high angular speeds- direct coupled with exhaust-driventurbine- less suited for mechanicalsupercharging
Consists of:stationary inlet casing,rotating bladed impeller,stationary diffuser (w or w/o vanes)collector - connects to intake system
Parameter Torque Peak Rated UnitsHorsepower 48 69 hp
BSFC 0.377 0.401 lb/hp-hrA/F 23.8 24.5 none
17 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
1
1
3
4
1
3
1
2 111
a
a
g
g
pp
m
mTCpTCp
pp
mechct
air
fuel
a
g
18 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Wt = Wc
. .
Heywood, 1988
Maximum possible closed-cycleefficiency (“ideal efficiency”)
State (1) to (2) isentropic(i.e., adiabatic and reversible)compression from max (V1) tomin cylinder volume (V2)Compression ratio rc = V1/V2.
State (2) to (3) adiabaticand isochoric (constant volume)combustion,State (3) to (4) isentropicexpansion.
State (4) to (1) exhaust process- available energy is rejected- can be converted to mechanicalor electrical work:
Ideal Engine Efficiency – Otto cycle
19 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Heywood, 1988
ηideal Function of only two variables, compression ratio (rc)and ratio of specific heats (γ)
Increasing rc increases operating volume for compression and expansionIncreasing γincreases pressure rise during combustion and increases workextraction during expansion stroke.
Both effects result in an increase in net system work for a given energy releaseand thereby increase engine efficiency.
Actual closed-cycle efficiencies to deviate from ideal:
1.) Assumption of isochoric combustion:Finite duration combustion in realistic engines.
Kinetically controlled combustion has shorter combustion duration than diesel or SI- duration limited by mechanical constraints, high pressure rise rates with audible
engine noise and high mechanical stresses2.) Assumption of calorically perfect fluid:
Specific heats decrease with increasing gas temperature; species conversion duringcombustion causes γto decrease
3.) Adiabatic assumption:Large temperature gradient near walls results in energy being lost to heat transferrather than being converted to crank work
20 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Other Assumptions:
In engine system models, compressors, supercharger, turbines modeled withconstant isentropic efficiency instead of using performance map.- typically, compressors, superchargers, and fixed geometry turbines have isentropic
efficiencies of 0.7. VGT has isentropic efficiency of 0.65.Charge coolers - intercooler, aftercooler, and EGR cooler modeled with zeropressure drop, a fixed effectiveness of 0.9, constant coolant temperature of 350 K.
21 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Zero-dimensional closed-cycle analysis:
Combustion represented as energy addition to closed system
Fuel injection mass addition from user-specified start of injection crank angle(θSOI) and injection duration (Δθinj).
Pressure and mass integrated over the closed portion of cycle with specifiedinitial conditions at IVC of pressure (p0), temperature (T0), and composition(xn,0 for all species considered - N2, O2, Ar, CO2, and H2O) and initial trappedmass (m0), including trapped residual mass
Minor species resulting from dissociation during combustion not considered
Herold, SAE 2011-01-2216
22 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Combustion model - Wiebe function
Heat transfer model - Woschni
First law energy balance: du=dq+pdv
Combustion:
Wall heat transfer:
23 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Herold, SAE 2011-01-2216
Friction model
Chen-Flynn model ( SAE 650733).
FMEP = C + (PF*Pmax) + (MPSF*Speedmp)
+ (MPSSF*Speedmp2)
where: C = constant part of FMEP (0.25 bar)
PF = Peak Cylinder Pressure Factor (0.005)
Pmax = Maximum Cylinder Pressure
MPSF = Mean Piston Speed Factor (0.1)
MPSSF = Mean Piston Speed Squared Factor (0)
Speedmp = Mean Piston Speed
BTE*LHV=IMEPg-PMEP-FMEP
DOE goal BTE=55%
Engine brake thermal efficiency BTE
24 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
0 5 10 15 20 25 3020
30
40
50
60
70
Load -- Gross IMEP [bar]
BT
E[%
]
GIE = 55%GIE = 60%GIE = 65%
PMEP = 0.4 barFMEP = 1 bar
150 bar PCP Limit
UW Dyno limit
UW RCCISCOTEresults(Exp/Sim)
{1 }PMEP FMEPBTE GIEIMEPg
45
55
Chen-Flynn SAE 650733).
Lavoie, 2012
1-D modeling for engine performance analysis – Lavoie et al. (2012)
25 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Mid load
26 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Lavoie, 2012
Burn duration Heat transfer
Friction
Turbocharger equation
m~0.8, Re increases with Bore and (boost)
27 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Woshni, 1967
Lavoie, 2012
Effect of combustion phasing on efficiency
Constant volume combustion
Without HT: Best efficiency CA50~TDCWith HT: best efficiency with CA50~10 deg – tradeoff between heat loss/late expansion
28 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Cum
ulat
ive
heat
rele
ase
Crank angle
10-90 Burn
CA50
10%
50%
90%
100%
Lavoie, 2012
63%
0 air standard efficiency
Adiabatic
Decreasing Incomplete combustion
Energy budget
29 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Lavoie, 2012
Fuel-to-charge equivalence ratio, ’
Bur
ned
gas
tem
pera
ture
ranges from 0.2 to 1 with air, EGR ranges from 0 to 80% with =1
Effect of dilution
30 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Lavoie, 2012
Effect of boost on efficiency
Reduced heat transfer loss
Reduced friction losses
31 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Lavoie, 2012
Potential brake efficiencies for naturally aspirated engines
Increased pumping losses
32 CEFRC2 June 27, 2012
Hour 2: Turbochargers, Engine Performance Metrics
Lavoie, 2012
Summary
33 CEFRC2 June 27, 2012
Turbocharging can increase engine efficiency by using available energy in exhaustand by reducing pumping work
Air standard “ideal cycle” analysis provides a bound on engine efficiencyestimates.
0-D engine system models provide estimates of engine system efficiencies,if combustion details (e.g., timing and duration) and heat transfer losses are assumed
The goal of multi-dimensional models (to be discussed next) is to predict thecombustion details