RAPID Kasutujuhend ENG

8/11/2019 RAPID Kasutujuhend ENG

1/28

RAPIDAluminium column formwork

Edition 02/2008

Assembly instructions for standard application


2/28


3/28 Legend

Important safety Hints Visual Check Site Tips

Page

Overview 1

Introduction 2Product features 2Intended use 2Safety instructions 3

Standard application

A1 Basic assemblyCutting-to-size of the formlining 4Formlining assembly with chamfer strip 4-5Formlining projection 5Sharp-edged solution 5Assembling the formwork halves 6

Crane lifting unit 6Push-pull props 7

A2 Safety systemConcreting platform 8Ladder access 9

A3 ShutteringPositioning the formwork 10Closing the formwork 11

A4 Application

Striking, moving 12Oversized cross-sections 13Height adjustment up to 8.10 m 14

A5 MiscellaneousMaintenance and Cleaning tips 15List of materials for the access ladder 16

Components 18-21

Contents


4/28

4

3

21

5 22

23

2425

27

21

26

11 121314

A1 Overview

RAPID column

1 Column frame

2 Corner profile with column

tie bolt and locking pin

3 Formlining

4 Chamfer strip

5 Crane lifting unit

Access ladder

21 Ladder connector Rapid

22 Access ladder 180/2

23 Ladder 180/6

24 Ladder hook

25 Ladder base

26 Ladder safety cage 75

Concreting platform (complete)

11 Concreting landing

12 Handrail 134 or 52

13Crane hook

14 Cam nut DW 15


5/282

These Assembly Instructions havebeen prepared in order to ensurecorrect assembly and safe use.

They describe the standard applicationof the PERI column formwork, RAPID,based on H = 3.0 m.

Introduction

The cross-section for square orrectangular-shaped columns is createdcontinuously using the wind millprinciple. Column frames are availablein three heights. They can be combinedwith each other and height incrementsof 30 cm are possible.

The access ladder with ladder safetycage and concreting platform form thesafety system for the PERI RAPID.It can be used for closing the column

formwork. Connections for push-pullprops and kicker braces are likewiseavailable in the system.

Care of the formwork is made simplerthrough the attachment of the cranelifting unit or concreting platform. Largedeposits of concrete are preventedfrom forming and any residual concreteis easily removed due to the powdercoating.

These assembly instructions containdetails regarding the intended use ofthe RAPID column formwork fromPERI. Safety instructions and loadspecifications must be observed at all

times.

Special permission must be givenby PERI if the formwork is to be usedfor applications other than thatwhich it has been designed for,together with supplementaryassembly instructions.

Product features

PERI RAPID is the column formworkfor joint-free architectural concrete

Basic assembly takes place with thecolumn frames in a horizontal positionand without the use of a crane. Theformlining sheets are cut to size andare clamped from above to the columnframework by means of clampingprofiles. With extended column frames,the formlining sheet can be fitted overthe element joint itself. Chamfer strips

are simply inserted between sheetingand clamping profile. Creation of sharp-edged column cross sections is alsopossible.

Two column frames with the integratededge connections are connected usingthe column tie yoke to form oneformwork half, fitted with appropriatesystem parts and then placed intoposition.

The intended use is presented in thebasic assembly instructions and theapplication of the safety equipment.

In addition, these assembly instructionsare supplemented by informationconcerning appropriate maintenancemeasures

Dimensions without any unit ofmeasurement are to be taken as cm.

The programme overview whichfollows at the end provides a detailedlook at all system componentscomplete with dimensions and itemnumbers. If you should have anyquestions, please contact your localPERI representative.

Technical data:Permissible fresh concrete pressure:120 kN/m2

Formlining:21 mm for chamfered columns30 mm for sharp edged columns

Column frame made of aluminium

Column cross-sections:square or rectangular-shaped

up to 60 x 60 cmSharp-edged columns:up to 58 x 58 cmOver-sized cross-sections from85 x 85 to 130 x 130 cm

Powder-coated column frame:H = 3.0 m, 2.10 m, 0.60 m

Intended use

Basically, only materials in perfectcondition may be used. Damagedcomponents must be replaced.

All valid laws and safety regulations

must be observed when using ourproducts.

This product is intended for commercialuse only.

These assembly instructions as wellas PERI offer and implementationplans do not replace specificconstruction site work and assemblyinstructions.


6/28


7/283

Care instructions for the formlinig

Concrete immersion vibrator withrubber cap minimizes possible damageto the formlining.

Spacers for the reinforcement withlarge support area minimizesindentations and markings.

Other regulationsIn particular, this currently includes: Operational Safety Regulations

(BetrSichV) Technical Regulations for Operational

Safety (TRBS)

AdditionalPERI product information PERI formwork technology design

tables

PERI RAPID brochure

Safety instructions

These assembly instructions areintended for those persons who work

with PERI RAPID column formwork.Non-observance of assemblyguidelines and safety instructions canlead to accidents and damage tomaterials.

Responsibilities of the user:

1. The user must ensure that allrequired instructions are at theoperators disposal (including theofficial assembly instructions).

2. All persons working with the

product must be familiar with thecontent of these instructions andsafety information.

3. The user must ensure that alloperators have a full and completeunderstanding of these instructionsand safety information.

4. The user must ensure thatassembly, adjusting anddismantling work carried out, aswell as correct use of the product,is supervised by trained andauthorised personnel.

5. The user is obliged to provide allrequirements to ensurecompliance with all applicablesafety regulations.

Safety information

1. All RAPID components are to bechecked before every use to makesure they are in perfect workingcondition!Damaged parts are to bereplaced by PERI originalcomponents!

2. All loads arising during the intendeduse must not be exceeded!

3. All load effects on the RAPIDformwork must be safelytransferred!

4. Stability must be guaranteedthroughout all building phases!

5. Never remove any safetyequipment!

6. Safe access ways must beprovided for site personnel to reachall working areas!

7. Working areas must have suitablesafety barriers to prevent sitepersonnel falling to the ground!

8. All openings must be fitted withsafety barriers!

9. Avoid using in areas of risk duringunfavourable weather conditions!

10. Striking is only to take place whenthe concrete is hard enough andsite management has given thego-ahead!

11. Striking or moving are to be carried

out using suitable tools andequipment! Do not tear awayformwork elements from theconcrete with the crane!

12. Remove all non-captivecomponents!

13. Equipment should not be usedin strong winds!

14. Remove lifting accessories from alowered formwork component orunit only when it is in a stablecondition!


8/284

A1 Basic assembly

Formlining assembly with chamferstrip

Cutting-to-size of the formlining

Plywood sheet: 21 mm

Horizontal formwork joints must bearranged on the lateral struts of theframes.

Width of plywoodExample:

Column width 55 cm 550 mm- reduction in size 8 mmCutting width of formlining 542 mm

Fig.1

Fig. 1

Fig. 2b

1. Place column frames on assemblytrestles. Fig.2a

Column width - 8 mm

SW 30

Fig. 2a

Fig. 2c

3. Mount plywood sheet and insert in theguide. Fig.2c

2. Bolt column frames together accordingto the required length (SW 30). Fig.2b


9/285

Sharp-edged solutionMax. cross-section dimensions580 x 580 mm.For forming without chamfer strips,a 30 mm thick plywood sheet isrequired which has been milledaccordingly. Fig.6

Width of plywood sheetExample:

Column width 550 mm

+ increase in size 12 mmCutting width of formlining 562 mm

It is held in position with the clampingprofile and guide. Fig.6aSecure plywood sheet against slipping.

A1 Basic assembly

Formlining assembly with chamferstrip

4. Position chamfer strip next to theplywood sheet. Fig.3

5. Push clamping profile over chamferstrip. Fig.3a

6. Tighten by means of G-clamps. Fig.4

7. Clamp in position the plywood sheetand chamfer strip with clamping profile.(SW 17 socket wrench)

8. Remove G-clamps.

9. Nail plywood sheet to prevent slipping.Use drilled holes in the guide. Fig.3a

Install plywood sheets in additionalcolumn frames in the same way.

Fig. 3a

Formlining projection

below approx. 40 mm above max. 200 mm with crane lifting

unit Fig.5

Fig. 3

Fig. 4

max.40

max.200

Fig. 5

30

8 8

8

6

5

Fig. 6a

Fig. 6

Dimensions in mm

Column width + 12 mm


10/286

A1 Basic assembly

Assembling the formwork halves

1. Place second pre-assembled column

frame on first column frame. Fig.7

2. Insert column tie yokes through thecorner connection.

3. Peg out using the locking pin in theperforated profile.

4. Tighten with nut. Fig.7a

5. Assemble second formwork half in thesame way.

Fig. 7

Fig. 7a

Crane lifting unit

One crane lifting unit per column frame,however not with the concretingplatform.(The crane lifting unit is already attachedhere to the concreting platform).

1. Loosen bolt, SW 30, in the column

frame.

2. Position crane lifting unit on the frameand secure with the bolt, SW 30.Fig.8 + 8a

Fig. 8

Fig. 8a

SW 30


11/287

A1 Basic assembly

Push-pull props

Mount 3 push-pull props to ensurestability!

Mount three brace connectors on oneformwork half. Fig.9

1. Pull out locking pins.

2. Fasten brace connector to perforatedprofile.

3. Insert brace connector in the perforated

profile and peg out with locking pins.Fig.9a

4. Fix push-pull prop and kicker bracewith bolts and cotter pins. Fig.10

Fig. 9

Fig. 9a

Fig. 10


12/288

a

b

c

SW 30

A2 Safety system

Concreting platform

The concreting platform is assembled

on horizontally-positioned columnhalves lying on the ground

1. Remove cam nut of the crane eye.

2. Remove bolt (SW 30) in the columnelement.

3. Position platform by hand on its edgedirectly against the formwork half.

4. Insert locking pin of the crane eyethrough the hole aof the columnelement and screw on cam nut.

5. Same procedure using hole b.

6. Align telescopic beam with hole candmount third crane eye. Fig.11

7. Install guardrails. Fig.12

Fig. 11

Fig. 12


13/289

SW 19

SW 19

Ladder access

The access ladder is assembled on

horizontally-positioned column halveslying on the ground.

1. Place ladder connection on frame andpeg out in the perforated profile withbolts. Fig.13

2. Pre-assemble ladder: connect access ladder 180/2 with

ladder 180/6, SW 19. Depending onthe height required, attach additionalladders 180/6.

mount ladder base and ladder hook onbottom ladder, SW 19. Fig.14

3. Attach the pre-assembled ladder withthe clamping plates to the ladderconnections, SW 19.

4. Mount ladder safety cage 150 or 75

with clamping plates according to plan.Clear spacing between the laddersafety cage elements 30 cm.

Visual check of the clamping plates.The contact surface must lie againstthe ladder profile.

5. For high columns:

Likewise install an access ladder forclosing the formwork in the oppositeformwork half.

A2 Safety system

Fig. 13

Fig. 14

Fig. 15


14/2810

A3 Shuttering

Positioning the formwork

Always erect the formwork half withthe concreting platform first.

Locating boards make it easier to alignthe formwork.

Formwork halves with concretingplatform (placing formwork)

1. Attach 3-sling lifting gear to crane eyes,lift formwork to a vertical position andtransport to place of use.

Fig.16

2. Position formwork halves againstlocating boards. Fig.17

3. Fix base plates of push-pull props andkicker braces to load-bearingfoundations/slab, e.g. with PERI MultiMonti. Fig.18

4. Check stability and make anynecessary adjustments.

5. Remove crane lifting gear.

The first formwork half is now inposition.

Fig. 16

Fig. 17

Fig. 18


15/2811

A3 Shuttering

Positioning the formwork

6. Attach lifting unit to crane eyes, lift2nd formwork halve to a verticalposition and transport to place of use.

7. Position this formwork half againstlocating boards. Fig.19

Closing the formwork

Use a second access ladder for highercolumns.

When closing the formwork, start atthe bottom and work upwards.

1. Insert column tie yoke through thecorner connection.

2. Peg out in the perforated profile withlocking pins.

3. Tighten with nut. Fig.20

4. Remove crane lifting gear.

The formwork is now in position.

Fig. 19

Fig. 20


16/2812

A4 Application

Striking, moving

Push-pull props, concreting platformand access ladder remain attached.

Formwork is opened from top tobottom.

The corner connections remainattached to the column frames (noindividual components).

Formwork halves without push-pullprops

1. Attach crane lifting gear to the non-supported formwork half and tension.

2. Separate corner connections betweenthe formwork halves: pull locking pinsand pull back column tie yokes.Fig.21

Use second access ladder.

3. Place formwork half on ground forcleaning.

Formwork halves with push-pullprops

1. Connect lifting gear to crane eyes ofthe concreting platform.

2. Remove base plates of push-pull propsand kicker braces from ground.

3. Place formwork half on ground forcleaning and secure.

Fig.21

Fig. 21


17/2813

A4 Application

Oversized cross-sections

Cross-sections from 85 x 85 cm to

130 x 130 cm

For oversized cross-sections, amaximum of two column frames(length and width) are connected witheach other. Connections are carriedout using the TRIO BFD alignmentcoupler.

1. For bracing, mount walers to every

perforated profile with column tie yokesand locking pins.

2. Insert anchor ties in the centre at thesame height as the walers.

Example Fig.22

Fig. 22

No. of pieces for each height

SRZ 120 U100

Height

BFD alignment coupler

steel walerColumn Frame 300 5 4

Column Frame 210 4 3

Column Frame 60 1 1


18/2814

A4 Application

Height adjustment up to 8.10 m

With three frame heights, height

adjustments are possible in 30 cmincrements.

Combination examples: Fig.21

The column frames are connectedusing M20 x 50 bolts (SW 30).Each RAPID frame is equipped withthese bolts Fig. 2b.

Larger heights are possible.

Height Column Frame

[m] 300 210 60

2.10 - 1 -

2.70 1 1

3.00 1 - -

3.30 - 1 2

3.60 1 - 1

3.90 - 1 3

4.20 - 2 -

4.50 - 1 4

4.80 - 2 1

5.10 1 1 -

5.40 - 2 2

5.70 1 1 1

6.00 2 - -

6.30 1 1 2

6.60 2 - 1

6.90 1 1 3

7.20 2 - 2

7.50 1 1 4

7.80 2 - 3

8.10 2 1 -


19/2815

A5 Miscellaneous

Maintenance tips

What needs to be done?

1. Spray formwork on all sides before first use witha release agent e.g. PERI BIO Clean.

2. Spray formlining every time after striking with PERIBio Clean, then clean.

3. For longer storage periods, e.g. bad weather, storeformwork materials in clean condition and sprayed.

4. Spray (grease if necessary) all moving partsregularly with a release agent.

5. Transport elements with suitable as well as safetransportation and lifting gear.

6. Ensure elements and accessories are properlystored.

7. Do not throw or drop accessories.

8. Never use unnecessary force during assemblyand dismantling.

Cleaning tips

Ensure elements are in a secure position duringcleaning!Cleaning of elements still attached to the craneis not allowed!Remove concrete surplus!

1. Immediately after concreting, spray the rear side

of the formwork with water.

2. After striking has taken place, spray formwork allover with PERI Bio Clean.

3. Remove nails, battens etc. from the plywoodbefore any mechanical cleaning.

4. Mechanically clean the elements using suitableequipment e.g. scraper.

5. Brush clean the elements after mechanical

cleaning. Remove dust and loosened concretesurplus.

6. After shuttering, element may require sprayingagain.

Why?

Provides good protection against sticking andcorrosion before first dirt accumulation.

Helps to remove concrete surplus and makes cleaningeasier. Removing by force or scraping off is notnecessary. Formlining and coating remain intact.

The frame is protected against corrosion andweathering.

Removes rust, prevents corrosion and keeps partsin good working order.

Avoids damage through improper transportation.

Prevents damage to the element frame andaccessories. Damage to the formlining throughindentations is avoided.

Maintains the functionality of the parts.

Maintains the functionality of the parts.

Concrete has not yet hardened and can easily be

removed. This reduces the amount of cleaningrequired.

Penetrates the concrete surplus, breaks it up andmakes subsequent mechanical cleaning much easier.

Unnecessary enlargement of nail holes and damageto the formlining is avoided. No damage to cleaningequipment.

Formlining surface is clean for the next use.


20/2816

A5 Miscellaneous

List of materials for the accessladder

For higher columns, mount twoaccess ladders!

Ladder access A:withaccess to the concreting platform

Ladder access B:withoutaccess to the concretingplatform, only for connecting the two

formwork halves

For heights of 7.80 m and more, werecommend the use of two concretingplatforms

Ladder access B Ladder access A

Item no. Description A* B* A* B* A* B* A* B* A* B* A* B*

037400 Concreting Platform, complete 1 0 1 0 1 0 1 0 1 0 1 0

051410 Ladder 180/6 2 2 2 2 3 3 4 4 5 5 6 6

103724 Access Ladder 180/2 1 0 1 0 1 0 1 0 1 0 1 0

051450 Ladder Safety Cage 150 0 0 1 1 2 2 3 3 4 4 5 5

104132 Ladder Safety Cage 75 1 1 1 0 2 1 2 1 2 1 2 1

051460 Ladder Base 1 1 1 1 1 1 1 1 1 1 1 1

103718 Ladder Hook 2 2 2 2 2 2 2 2 2 2 2 2

103369 Ladder Connector RAPID 2 2 2 2 3 3 4 4 5 5 6 6

2.70 3.90 4.50 6.00 7.80 9.60

3.60 m 4.20 m 5.70 m 7.50 m 9.30 m 10.80 m

A*= ladder access AB* = ladder access B


21/28


22/28

290

205

165

20

16

20

20

35

15

15

5

4

794

600

300

654

120

19x30=57025

60 80

23

21

800

243

500 64

794

2100

250

800

800

250

250

1000

794

3000

1000

500

250

18

Column Frames RAPID, AluFor column cross section up to 600x600mm.Complete with:Clamping Profile, Column Tie Yoke DW15,Spherical Nut DW15, galv., Locking Pin 20x205, galv., and Hex. Bolt ISO 4017M20x50-8.8, galv. with Hex. NutISO 7042 M20-8, galv. (2x).

Column Frame 300 59,90 037250Column Frame 210 42,70 037260Column Frame 60 14,30 037270

Chamfer Strip RAPID L = 3,00m 0,32 037210For clamping plywood to the ColumnFrames RAPID.

Brace Connector-3 RAPID, galv. 3,05 037190For fixing Push-Pull Props andKicker Braces to the Column Frames RAPID.Complete with:Locking Pin 20x205, galv. (1x)Pin 16x42, (1x), and Cotter Pin 4/1 (2x).

Weight kg Item no.

20x205FS 4/1

16x42FS 4/1

DW15

M20x50


23/28

106

68

125

120

205

20

20

34

290

28

21

42

250

100

119

400 118

400118

500

798

18

22

178

230

195

50

260

661

469SW 19

19

Crane Lifting Unit-2 RAPID 14,00 0373204 for a fully assembled column form.Only 2 needed when a concreting platformis used.

Load-bearing pointPermissible load: 500kg

Column Tie Yoke DW15 0,60 037150For tying RAPID Column Frames.Comes with the RAPID Column Frames.For Column Frame 300 (4x), 210 (3x), 60 (1x)

Permissible Load to DIN 18216: 90kN

Locking Pin 20x205, galv. 0,74 037160For tying RAPID Column Frames.Comes with the RAPID Column Frames.For Column Frame 300 (4x), 210 (3x), 60 (1x)Complete with:Cotter Pin 4/1 (1x)

Spherical Nut DW 15, galv. 0,49 030440For tying RAPID Column Frames.Comes with the RAPID Column Frames.For Column Frame 300 (4x), 210 (3x), 60 (1x)

Permissible Load to DIN 18216: 90kN

Ladder connector RAPID, galv. 6,58 103369For connecting ladders to RAPIDcolumn frames.Complete with:Hex. Bolt ISO 4017 M12x25-8.8, galv. (2x) andClamping plate (2x)

Weight kg Item no.

SW 27

DW15

FS 4/1

DW15


24/28

20 405 4020

130

50

130

20 13

1810

25

220

155

1960

5

x

298

=1

490

95

40025

405

25

100

210

50

53

130

40

13

80

80

50

400

534

1885

1200

220

168

298

405

120

320

355

50

50

325

294

710

450

750

(1500)

79

25

20

20

Weight kg Item no.

Ladder 180/6, galv. 13,10 051410Access Ladder 180/2, galv. 11,10 103724Complete with:Hex. Bolts ISO 4017 M12x40-8.8, galv. andHex. Nut ISO 7042 M12-8, galv. (4x)

Accessories:Formwork chain 3kN, 2,5m 1,37 065073

Ladder Hook, galv. 0,68 103718Only for the lower ladder (2x)Complete with:Hex. Bolt ISO 4017 M12x25-8.8, galv. andHex. Nut ISO 7042 M12-8, galv. (2x)

Ladder Base 2,36 051460For preventing the ladders sliding.

Ladder Safety Cage 75, galv. 15,50 104132Ladder Safety Cage 150, galv. 25,20 051450Complete with:Hex. Bolt ISO 4017 M12x25-8.8, galv. (4x),Clamping plate (4x)

SW 19

Eyes for security chain

SW 19


25/28

840

520

1340

1005

100

525

74

137 60

225

150 19

70

1524

1420

1340

52540

1524

50052 5

710

40

20

14

1305

38

50

110

130

21

Concreting Platform, complete 126,00 037400Used for TRIO, RAPID and QUATTRO columns.Consisting of:Concreting Landing (1x)Handrail 52 galv. (2x)Handrail 134 galv. (2x)Crane Hook Concreting Platform (3x)

Concreting Landing, Alu 51,50 037410Powder-coatedSuitable for any cross section up to amaximum of 600x600mm. It is mountedwith the Crane Hook Concreting Platform.

Permissible Load: 150kg/m2

Handrail 52, galv. 10,50 037420

Handrail 134, galv. 18,10 0374302 of each per concreting platform.Locks in place automatically.

Crane Hook Concreting Platform 5,70 0374403 per concreting platform.Complete with: Captive Fixing Pinand Cam Nut DW15, galv.

Load-bearing pointPermissible load: 1000kg

Weight kg Item no.

adjustable620

DW15

Eyes for security chain


26/2822

02 PERI S.A.S. Zone Industrielle Nord 34-36 rue des Frres Lumire 77109 Meaux Cedex

[email protected] www.peri.fr

03 PERI AG Aspstrae 17 8472 Ohringen [email protected] www.peri.ch

04 PERI S.A. Sociedad Unipersonal Ctra. Paracuellos - Fuente el Saz km. 18,9 Camino de Malatones, km. 0,5 28110 Algete/Madrid [email protected] www.peri.es

05 N.V. PERI S.A. Industriepark Nijverheidsstraat 6 PB 54 1840 Londerzeel [email protected] www.peri.be

06 PERI B.V. v. Leeuwenhoekweg 23 Postbus 304 5480 AH-Schijndel [email protected] www.peri.nl

07

PERI Formwork Systems, Inc. 7135 Dorsey Run Road Elkridge, MD 21075

[email protected] www.peri-usa.com

08 PT Beton Perkasa Wijaksana P.O. Box 3737 Jakarta 10210 [email protected]

www.peri.de

09

PERI S.p.A. Via G. Pascoli, 4 20060 Basiano (MI) [email protected] www.peri.it

10 PERI Japan K.K. 7F Hakozaki 314 Building, 31-4 Hakozaki-cho, Nihonbashi Chuo-ku Tokyo 103-0015 [email protected] www.perijapan.jp

11 PERI Ltd.

Market Harborough Road Clifton upon Dunsmore Rugby, CV23 0AN [email protected] www.peri.ltd.uk

12 PERI Kalp ve skeleleri San. ve Tic. Ltd. Sti. akmakl Mahallesi Akaburgaz Cad. 72. Sokak No: 23 Kra - Bykekmece/

Istanbul 34500 [email protected] www.peri.com.tr

13 PERI Kft. Zdor u. 4.

1181 Budapest [email protected] www.peri.hu

14 PERI Formwork Malaysia Sdn. Bhd. Unit 19-07-4, Level 7 PNB Damansara

19 Lorong Dungun Damansara Heights 50490 Kuala Lumpur

[email protected] www.perimalaysia.com

15 PERI ASIA Pte. Ltd Formwork Pte. Ltd. No. 1 Sims Lane # 06-10 Singapore 387355 [email protected] www.periasia.com

16 PERI Ges.mbH Traisenstrae 3 3134 Nudorf ob der Traisen [email protected] www.peri.at

17 PERI spol. s r.o. Prmyslov 392 252 42 Jesenice [email protected] www.peri.cz

18 PERI Danmark A/S forskalling og stillads Greve Main 26 2670 Greve [email protected] www.peri.dk

19

PERI Suomi Ltd. Oy Hakakalliontie 5 05460 Hyvink

[email protected] www.perisuomi.fi

20 PERI NORGE AS Kobbervikdalen 156 3036 Drammen [email protected] www.peri.no

21 PERI Polska Sp. z o.o. ul. Stoeczna 62 05-860 Pochocin [email protected]

www.peri.pl.pl

22

PERIform SVERIGE AB Montrgatan 4-6 Box 9073 30013 Halmstad [email protected] www.periform.se

23 PERI (Korea) Ltd. 8-9th Fl., Yuseong Bldg. 830-67, Yeoksam-dong, Kangnam-ku, Seoul 135-080 [email protected] www.perikorea.com

24

PERIcofragens Lda. Cofragens e Andaimes Rua Cesrio Verde, n 5 - 3 Esq. Linda-a-Pastora

2790-326 Queijas [email protected] www.peri.pt

25 PERI S.A. Ruta Nacional N. 9, km 47,5 (Panamericana Ramal Escobar) (1625) Escobar/Prov. Bs. As. [email protected] www.peri.com.ar

26 PERI Formas e Escoramentos Ltda.

Rodovia Raposo Tavares, km 41 Colinas Bandeirante CEP 06730-000

Vargem Grande Paulista

So Paulo [email protected] www.peribrasil.com.br

27 PERI Chile Ltda. C/Jos de San Martin N 104 Parque Industrial Los Libertadores

Colina, Santiago de Chile [email protected] www.peri.cl

28 PERI Romnia SRL Calea Bucureti nr. 2B 077015 Baloteti - ILFOV [email protected] www.peri.ro

29 PERI SLOWENIEN Goran Opalic Obrena 137 2000 Maribor [email protected] www.peri.de

30

PERI spol. s r.o. amornska 18 903 01 Senec [email protected] www.peri.sk

31 PERI Australia Pty. Ltd. 116 Glendenning Road Glendenning NSW 2761 [email protected] www.periaus.com.au

32 PERI AS Valdme 8 Tnassilma Tehnopark 76401 Saku vald Harjumaa [email protected]

www.peri.ee

2

1

3

4

5

6

9

11

12

1316

17

18

19

20

22

21

24

2829

30

32

33

34

38

41

42

46

48

52

53

01 PERI GmbH Rudolf-Diesel-Strasse 89264 Weissenhorn [email protected] www.peri.de

France

Switzerland

Spain

Belgium/Luxembourg

Netherlands

USA

Indonesia

Italy

Japan

United Kingdom/Ireland

Turkey

Hungary

Malaysia

Singapore

Austria

Czech Republic

Denmark

Finland

Norway

Poland

Sweden

Korea

Portugal

Argentina

Brazil

Chile

Romania

Slovania

Slovakia

Australia

Estonia

PERI International


27/2823

33 PERI Hellas Ltd. Sokratous Str. 5th kil. Koropi-Varis Ave. P. O. Box 407

194 00 Koropi [email protected] www.perihellas.gr

34 PERI SIA Granita 26 1057 Riga [email protected] www.peri-latvija.lv

35 PERI (L.L.C.) Brashy Building, Office No. 212 Shk. Zayed Road P.O. Box 27933 Dubai [email protected] www.perime.com

36 PERI Formwork Systems, Inc. 45 Nixon Road Bolton, Ontario

L7E 1K1 [email protected] www.peri.ca

37 PERI GmbH Lebanon Representative Office AYA Commercial Center, 7th floor, Dora Highway, Beirut

P.O. Box 90 416 Jdeidet [email protected] www.peri.de

38

PERI UAB Titnago st. 19 02300 Vilnius [email protected] www.peri.lt

39 PERI S.A. Route de Rabat, km. 5 Piste de Beni Touzine Tanger

[email protected] www.peri.de

40 PERI Formwork Engineering Ltd 16 Moshe Dayan st., P.O. Box 10202 Petach Tikva, 49002 Israel [email protected] www.peri.co.il

41 PERI BULGARIA EOOD Kv. Vragdebna m. Nova Machala Nr. 46 1839 Sofia [email protected] www.peri.bg

42 MEST ltd., Fornubudum 5 220 Hafnarfjordur [email protected] www.mest.is

43 TOO PERI Kazakhstan Rubenstein Street 10 (Corner Dostyk Str. 7) 050010 Almaty [email protected] www.peri.kz

44

OOO PERI 8 Etage, OOO PERI Buro Krasnaya Presnya Str. 24

123022 Moskau [email protected] www.peri.ru

45 PERI Wiehahn (Pty.) Ltd. P.O. Box 2668 Bellville 7535 [email protected]

www.periwiehahn.co.za

46

TOW PERI Ukraina 23, M. Raskowa Str., B. 822 02002 Kiew [email protected] www.peri.ua

47 PERI GmbH Egypt Branch Office 24 A, Obour Gardens, 4th Floor, apt. # 1 Salah Salem Street 11361 Heliopolis

Cairo [email protected] www.peri.com.eg

48 PERI Oplate d.o.o. Jurija Gagarina 81 11070 Novi Beograd [email protected] www.peri.co.yu

49 PERI Cimbras y Andamios, S.A. de C.V. Parque de las Amricas KM 3.5 de la Carretera Jorobas - Tula Huehuetoca Estado de Mxico,

C.P. 54680 [email protected] www.peri.com.mx

50

PERI Kalp ve skeleleri Baku Branch Office 28 May K. Ev 72 Menzil 27 Baku [email protected] www.peri.com.tr

51PERI Kalp ve skeleleri

Agabat Branch Office Groglu Sokak No. 130, Kat 2 744035 Agabat

[email protected] www.peri.com.tr

52 PERI Belarus Pr. Nesawisimosti 11 Kopus-2 Zimmer: 526,528 220030 Minsk [email protected] www.peri.com.tr

53 PERI oplate i skele d.o.o. Dolenica 20 10 250 Donji Stupnik/

Zagreb [email protected] www.peri.com.hr

54

PERI GmbH Iran Branch Office Flat 27, Blvd. KAVE,

Building No. 246 P.O. Box 9 3979 3669 Tehran [email protected] www.peri.ir

55 PERI (India) Pvt Ltd 717 Palm Springs Palm Court Malad Link Road Malad (West) Mumbai 400064 [email protected] www.peri.in

56 PERI Jordan Saad 5 Center, 4th Floor Office No. 404 Al Madineh

Al Munawara Street P.O. Box 367 11947 Amman

[email protected] www.peri.de

57 PERI Kuwait Arraya Center, 29th Floor Al-Shuhada Street, Sharq P.O. Box 1060 Safat 13011 Kuwait [email protected] www.peri.de

58 PERI Saudi Arabia 33 AL-Batraa Street AL -Shurbatiy Building AL - Bughdadiah AL -

Gharbiah Distrect 6th Floor, Flat # 61 P.O. Box 11641 Jeddah [email protected] www.peri.de

59 PERI Qatar LLC P.O. Box 24133 Doha [email protected] www.peri.de

60 Socit PERI S.A.S. Bureau de liaison dAlger 50 bis, Route de Gu de Constantine Hai El Badr (ex Apreval)

Immeuble FADLI Kouba - Alger

[email protected] www.peri.fr

7

8

10

1415

23

25

26

2731

35

36

3739 40

43

44

45

4749

5051

54

595558

5760 56

Greece

Latvia

United Arab Emirates

Canada

Libanon

Lithuania

Marocco

Israel

Bulgaria

Iceland

Kazakhstan

Russian Federation

South Africa

Ukraine

Egypt

Serbia

Mexico

Azerbaijan

Turkmenistan

Belorussia

Croatia

Iran

India

Jordan

Kuwait

Saudi Arabia

Qatar

Algeria


28/28

De

02/2008

3ma

Art.

Nr.:792216

C

opyrightbyP

ERIGmbH

Wall Formwork

Panel FormworkGirder FormworkCircular FormworkFacade FormworkBrace Frame

Column Formwork

Square

RectangularCircular

Slab Formwork

Panel FormworkBeam Grid FormworkGirder FormworkSlab TableBeam Formwork

Shoring Systems

Steel Slab PropsAluminium Slab PropsTower SystemsHeavy-Duty Props

Climbing Systems

Climbing ScaffoldSelf-Climbing SystemClimbing Protection PanelPlatform Systems

Scaffold, Stairways,

Working Platforms

Facade ScaffoldWorking PlatformWeather Protection RoofStairway Access

Bridge and Tunnel

Formwork

Cantilevered Parapet CarriageCantilevered Parapet PlatformEngineers Construction Kit

Services

Formwork AssemblyCleaning / RepairsFormwork PlanningSoftwareStaticsSpecial Constructions

Additional Systems

PlywoodFormwork GirdersStopend SystemsPalletsTransportation Containers

PERI GmbH

Formwork Scaffolding Engineering

P.O. Box 126489259 Weissenhorn

GermanyTel +49 (0)73 09.9 50- 0Fax +49 (0)73 09.9 51- 0info@peri de

PERI Product Range

RAPID Kasutujuhend ENG

Documents