r61526_spec

LCD MODULE SPECIFICATION

Model : MI0240ZT-1

Revision 1.0 Engineering Date Our Reference

MULTI-INNO TECHNOLOGY CO., LTD.

REVISION RECORD

REV NO. REV DATE CONTENTS REMARKS

0.1 2010-10-11 First release Preliminary

1.0 2010-11-2 Full spec /

P.2 MULTI-INNO TECHNOLOGY CO.,LTD.

MODULE NO.: MI0240ZT-1 Ver 1.0

CONTENTS

GENERAL INFORMATION EXTERNAL DIMENSIONS ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS BACKLIGHT CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS INTERFACE DESCRIPTION REFERENCE APPLICATION CIRCUIT RELIABILITY TEST CONDITIONS INSPECTION CRITERION PRECAUTIONS FOR USING LCD MODULES PACKING SPECIFICATION PRIOR CONSULT MATTER



GENERAL INFORMATION

Item Contents Unit LCD type TFT/TRANSMISSIVE / Recommended Viewing Direction Full viewing angle O Clock Module area (W H T) 42.7260.261.85 mm3 Viewing area (WH) 38.7250.96 mm2 Active area (WH) 36.7248.96 mm2 Number of Dots 240RGB320 / Pixel pitch (W H) 0.1530.153 mm2 Driver IC R61526 / Interface Type System parallel interface / Input voltage 2.8 V Module Power consumption 258 mw Colors 262K / Backlight Type LED /



EXTERNAL DIMENSIONS

7.VAmds:

,

VAmds

0.3mm

6.ROHS COMPLIANCY

5.BACKLIGHT:4CHIP-WHITE LED,PARALLEL CONNECTION

4.LCD DRIVER: R61526

3.STORAGE TEMP: -30C~80C

2.OPERATING TEMP: -20C~70C

1.DISPLAY TYPE: 262K TFT,TRANSMISSIVE

NOTES:

AK

FPC



ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Min Max Unit Supply voltage for logic VCC/IOVCC -0.3 4.6 V Input voltage VIN -0.3 IOVCC+0.3 V Operating temperature Top -20 70 C Storage temperature TST -30 80 C Humidity RH - 90%(Max60 C) RH ELECTRICAL CHARACTERISTICS DC CHARACTERISTICS

Parameter Symbol Min Typ Max Unit Supply voltage for logic VCC 2.7 2.8 2.9 V I/O power supply IOVCC 1.7/2.7 1.8/2.8 1.9/2.9 V Input Current Icc - 11.74 23.48 mA Input voltage 'H' level VIH 0.8IOVCC - IOVCC V Input voltage 'L' level VIL 0 - 0.2IOVCC V Output voltage 'H' level VOH 0.8IOVCC - - V Output voltage 'L' level VOL - - 0.2IOVCC V BACKLIGHT CHARACTERISTICS

Item Symbol Min. Typ. Max. Unit Condition Forward voltage Vf 3.0 3.2 3.4 V Luminance Lv 3800 4200 4600 cd/m2

If=60mA Ta=25

Number of LED - - 4 - Piece - Connection mode P - Parallel - - - Using condition: constant current driving method If=60mA(+/-10%).



ELECTRO-OPTICAL CHARACTERISTICS

Item Symbol Condition Min Typ Max Unit Remark Note Response time Tr+ Tf - 13 20 ms Fig.1 4 Contrast ratio Cr 300 1025 - --- FIG 2. 1 Luminance uniformity WHITE 74 82 - % FIG 2. 3 Surface Luminance Lv

=0 =0 Ta=25

260 325 - cd/m2 FIG 2. 2

= 90 70 80 - deg FIG 3. = 270 58 68 - deg FIG 3. = 0 70 80 - deg FIG 3.

Viewing angle range

= 180 70 80 - deg FIG 3.

6

NTSC ratio --- --- - 71 - % - - Red x 0.5828 0.6328 0.6828 - Red y 0.2789 0.3289 0.3789 - Green x 0.2700 0.3200 0.3700 - Green y 0.5529 0.6029 0.6529 - Blue x 0.0964 0.1464 0.1964 - Blue y - 0.0299 0.0799 - White x 0.2229 0.2829 0.3429 -

CIE (x, y) chromaticity

White y

=0 =0 Ta=25

0.2340 0.2940 0.3540 -

FIG 2. 5

Note1. Contrast Ratio(CR) is defined mathematically by the following formula. For more

information see FIG 2.:

( )( )AverageSurface Luminance with all white pixels P 1, P2, P 3, P4, P5

ContrastRatio = Average SurfaceLuminance with all black pixels P1, P2, P 3, P4, P5

Note2. Surface luminance is the LCD surface from the surface with all pixels displaying white. For more information see FIG 2.

Lv = Average Surface Luminance with all white pixels (P1, P2, P 3,P4, P5) Note3. The uniformity in surface luminance WHITE is determined by measuring luminance at

each test position 1 through 5, and then dividing the maximum luminance of 5 points luminance by minimum luminance of 5 points luminance. For more information see FIG 2.

, ,

Surface Luminance with all white pixels ( , , , ) WHITE =

Maxi Surface Luminance with allwhite pixels ( , , , ) 1 2 3 4 5

1 2 3 4 5

Minimum P P P P Pmum P P P P P

Note4. Response time is the time required for the display to transition from White to black(Rise Time, Tr) and from black to white(Decay Time, Tf). For additional information see FIG 1..

Note5. CIE (x, y) chromaticity ,The x,y value is determined by screen active area position 5. For more information see FIG 2.

Note6. Viewing angle is the angle at which the contrast ratio is greater than 2. For TFT module the conrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 3.

Note7. For Viewing angle and response time testing, the testing data is base on Autronic-Melcherss ConoScope. Series Instruments. For contrast ratio, Surface Luminance, Luminance uniformity and CIE the testing data is base on TOPCONs BM-5 photo detector.

Note8. For TFT transmissive module,Gray scale reverse occurs in the direction of panel viewing angle.



FIG.1. The definition of Response Time

FIG.2. Measuring method for Contrast ratio,surface luminance, Luminance uniformity,CIE (x,

y) chromaticity

FIG.3. The definition of viewing angle

A : 5 mm B : 5 mm H,V : Active Area Light spot size =5mm, 500mm distance from the LCD surface to detector lens measurement instrument is TOPCONs luminance meter BM-5



INTERFACE DESCRIPTION Interface

NO. Symbol I/O or

connect to Description When not in

use 1 GND Power supply POWER GROUND -

2 Y- TP driver Touch panel coordinate in the down side of envisage drawing. OPEN

3 X- TP driver Touch panel coordinate in the right side of envisage drawing. OPEN

4 Y+ TP driver Touch panel coordinate in the up side of envisage drawing. OPEN

5 X+ TP driver Touch panel coordinate in the left side of envisage drawing. OPEN

6 GND Power supply POWER GROUND - 7 NC 8 NC 9 NC 10 NC

- No connection -

11 LCD_ID O Host processor Output a voltage for identity. See note1 OPEN

12 RESET I Host processor Reset pad. Initializes the IC when it is low. Must be reset after power-on. Amplitude: IOVCC-GND -

13 FMARK O Host processor

Frame head pulse signal, which is used when writing data to the internal RAM.(Amplitude: IOVCC-GND).

OPEN

14 NC - No connection - 15 DB15 16 DB14 17 DBB13 18 DB12 19 DB11 20 DB10 21 DB9 22 DB8

I/O Host processor

8-bit parallel bi-directional data bus for 80-system interface operation (Amplitude: IOVCC-GND).

-

23 NC 24 NC 25 NC 26 NC 27 NC 28 NC 29 NC 30 NC

- No connection -

31 RD I Host processor

Read strobe signal in 80-system bus interface operation and enables read operation when RDX is low. Amplitude: IOVCC-GND

IOVCC

32 WR I Host processor

Write strobe signal in 80-system bus interface operation and enables write operation when WRX is low. Synchronous clock signal (SCL) in serial interface operation. Amplitude: IOVCC-GND

IOVCC



33 RS I Host processor

Register select signal. Amplitude: IOVCC-GND Low: select Index register High: select control register

IOVCC

34 CS I Host processor

Chip select signal. Amplitude: IOVCC-GND Low: the driver is selected and accessible High: the driver is not selected and not accessible.

IOVCC

35 GND Power supply POWER GROUND -

36 IOVCC Power supply Power supply to the interface pins I/O. 1.8V/2.8V(typ) -

37 VCC Power supply Power supply to internal logic regulator circuit and Power supply to the liquid crystal power supply analog circuit. 2.8V~3.0V

-

38 VCC Power supply Power supply to internal logic regulator circuit and Power supply to the liquid crystal power supply analog circuit. 2.8V~3.0V

-

39 LEDK4 LED driver LED 4( CATHODE ) - 40 LEDK3 LED driver LED 3( CATHODE ) - 41 LEDK2 LED driver LED 2( CATHODE ) - 42 LEDK1 LED driver LED 1( CATHODE ) - 43 LEDA LED driver LED ANODE - 44 GND Power supply POWER GROUND - Note1:

REFERENCE APPLICATION CIRCUIT Please consult our technical department for detail information.



RELIABILITY TEST CONDITIONS No. Test Item Test Condition Inspection after test

1 High Temperature Storage 802/200 hours 2 Low Temperature Storage -302/200 hours 3 High Temperature Operating 702/120 hours 4 Low Temperature Operating -202/120 hours

5 Temperature Cycle storage -202~25~70210cycles (30min.) (5min.) (30min.)

6 Damp proof Test operating 50590%RH/120 hours

7 Vibration Test

Frequency10Hz~55Hz~10Hz Amplitude1.5mm, XYZ direction for total 3hours (Packing condition)

8 Dropping test Drop to the ground from 1m height, one time,every side of carton. (Packing condition)

9 ESD test Voltage:8KV R: 330 C: 150pF Air discharge, 10time

Inspection after 2~4hours storage at room temperature, the sample shall be free from defects: 1.Air bubble in the LCD; 2.Sealleak; 3.Non-display; 4.missing segments; 5.Glass crack; 6.Current Idd is twice higher than initial value.

Remark: 1.The test samples should be applied to only one test item. 2.Sample size for each test item is 5~10pcs. 3.For Damp Proof Test, Pure water(Resistance10M) should be used. 4.In case of malfunction defect caused by ESD damage, if it would be recovered to normal state after resetting, it would be judged as a good part. 5.EL evaluation should be excepted from reliability test with humidity and temperature: Some defects such as black spot/blemish can happen by natural chemical reaction with humidity and Fluorescence EL has. 6.Failure Judgment Criterion: Basic Specification, Electrical Characteristic, Mechanical Characteristic, Optical Characteristic.



INSPECTION CRITERION

OUTGOING QUALITY STANDARD PAGE 1 OF 4

TITLE:FUNCTIONAL TEST & INSPECTION CRITERIA MDS Product

This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling plan according to GB/T2828.1-2003/ISO 2859-11999 and ANSI/ASQC Z1.4-1993, normal level 2 and based on: Major defect: AQL 0.65

Minor defect: AQL 1.5 2. Inspection condition

Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45against perpendicular line. 3. Definition of inspection zone in LCD. Zone A: character/Digit area Zone B: viewing area except Zone A (ZoneA+ZoneB=minimum Viewing area) Zone C: Outside viewing area (invisible area after assembly in customers product) Fig.1 Inspection zones in an LCD. Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for

quality and assembly of customers product.

C

B A





4. Inspection standards 4.1 Major Defect

Item No

Items to be inspected Inspection Standard

Classification of defects

4.1.1

All functional defects

1) No display 2) Display abnormally 3) Missing verticalhorizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting.

4.1.2 Missing Missing component

4.1.3

Outline dimension

Overall outline dimension beyond the drawing is not allowed.

Major

4.2 Cosmetic Defect Item No



For dark/white spot, sizeis defined y

as = 2

)( yx + x

1

Acceptable Qty Zone Size(mm)

A B C

0.10 Ignore

0.100.15 2

0.150.20 1

Clear Spots Black and white Spot defect Pinhole, Foreign Particle, Dirt under polarizer

0.20 0

Ignore

Minor

4.2.1

Dim Spots

Circle shaped and dim edged

defects

2.

Acceptable Qty 2. Zone Size(mm) A B C

0.2 Ignore

0.200.40 3

0.400.60 2

0.600.80 1

Ignore

0.80 0

Minor




TITLE: FUNCTIONAL TEST & INSPECTION CRITERIA MDS Product

4.2. Cosmetic Defect

Item No



Size(mm) Acceptable Qty Zone

L(Length) W(Width) A B C

Ignore W0.02 Ignore

L3.0 0.02W0.03 2

L2.0 0.03W0.05 1

0.05W Define as spot defect

Ignore

4.2.2

Line defect Black line, White line, Foreign material under polarizer,

Minor

4.2.3

Polarizer scratch

If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by the line defect of 4.2.2. If the Polarizer scratch can be seen only in non-operating condition or some special angle, judge by the following.

Size(mm) Acceptable Qty

Zone L(Length) W(Width)

A B C

Ignore W0.03 Ignore

5.0L10.0 0.03W0.05 2

L5.0 0.05W0.08 1

0.08W 0

Ignore

Minor

4.2.4

Polarize

Air bubble

Air bubbles between glass & polarizer

Acceptable Qty 2. Zone Size(mm) A B C

0.2 Ignore

0.200.30 2

0.300.50 1

0.50 0

Ignore

Minor





4.3. Cosmetic Defect

Item No



(i) Chips on corner

Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal.

X Y Z 2.0 S Disregard

Minor

(ii)Usual surface cracks

X Y Z

3.0

PRECAUTIONS FOR USING LCD MODULES 1 Handing Precautions

1.1 The display panel is made of glass and polarizer. As glass is fragile. It tends to become or

chipped during handling especially on the edges. Please avoid dropping or jarring. Do not subject it to a mechanical shock by dropping it or impact.

1.2 If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.

1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. Do not touch the display with bare hands. This will stain the display area and degraded insulation between terminals (some cosmetics are determined to the polarizer).

1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.). Do not put or attach anything on the display area to avoid leaving marks on it. Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizer. After products are tested at low temperature they must be warmed up in a container before coming in to contact with room temperature air.

1.5 If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavily contaminated, moisten cloth with one of the following solvents

- Isopropyl alcohol - Ethyl alcohol Do not scrub hard to avoid damaging the display surface.

1.6 Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the following.

- Water - Ketone - Aromatic solvents Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. Avoid contact with oil and fats.

1.7 Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets, moisture condensation or a current flow in a high-humidity environment.

1.8 Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable.

1.9 Do not attempt to disassemble or process the LCD module. 1.10 NC terminal should be open. Do not connect anything. 1.11 If the logic circuit power is off, do not apply the input signals. 1.12 Electro-Static Discharge ControlSince this module uses a CMOS LSI, the same careful

attention should be paid to electrostatic discharge as for an ordinary CMOS IC. To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment.

- Before removing LCM from its packing case or incorporating it into a set, be sure the module and your body have the same electric potential. Be sure to ground the body when handling the LCD modules. - Tools required for assembling, such as soldering irons, must be properly grounded. Make certain the AC power source for the soldering iron does not leak. When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor. - To reduce the amount of static electricity generated, do not conduct assembling



and other work under dry conditions. To reduce the generation of static electricity be careful that the air in the work is not too dry. A relative humidity of 50%-60% is recommended. As far as possible make the electric potential of your work clothes and that of the work bench the ground potential. - The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated.

1.13 Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it.

- Do not alter, modify or change the shape of the tab on the metal frame. - Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. - Do not damage or modify the pattern writing on the printed circuit board. - Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector. - Except for soldering the interface, do not make any alterations or modifications with a soldering iron. - Do not drop, bend or twist the LCM.



2 Handling precaution for LCM

2.1 LCM is easy to be damaged. Please note below and be careful for handling. 2.2 Correct handling:

2.3 Incorrect handling:

As above picture, please handle with anti-static gloves around LCM edges.

Please dont hold the surface of panel.

Please dont touch IC directly. Please dont stack LCM.

Please dont operate with sharp stick such as pens.

Please dont stretch interface of output, such as FPC cable.

Please dont hold the surface of IC.



3 Storage Precautions

3.1 When storing the LCD modules, the following precaution are necessary. 3.1.1 Store them in a sealed polyethylene bag. If properly sealed, there is no need for the

desiccant. 3.1.2 Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the

temperature between 0C and 35C, and keep the relative humidity between 40%RH and 60%RH.

3.1.3 The polarizer surface should not come in contact with any other objects (We advise you to store them in the anti-static electricity container in which they were shipped).

3.2 Others

3.2.1 Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature.

3.2.2 If the LCD modules have been operating for a long time showing the same display patterns, the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be regained by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability.

3.2.3 To minimize the performance degradation of the LCD modules resulting from destruction caused by static electricity etc., exercise care to avoid holding the following sections when handling the modules.

3.2.3.1 - Exposed area of the printed circuit board. 3.2.3.2 -Terminal electrode sections.

4 USING LCD MODULES 4.1 Installing LCD Modules

The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the following items when installing the LCM.

4.1.1 Cover the surface with a transparent protective plate to protect the polarizer and LC cell.

4.1.2 When assembling the LCM into other equipment, the spacer to the bit between the LCM

and the fitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The measurement tolerance should be 0.1mm.



4.2 Precaution for assemble the module with BTB connector: Please note the position of the male and female connector position, dont assemble or assemble like the method which the following picture shows



4.3 Precaution for soldering the LCM Manual soldering Machine drag soldering Machine press soldering

No RoHS Product

290C ~350C. Time : 3-5S.

330C ~350C. Speed : 15-17 mm/s.

300C ~330C. Time : 3-6S. Press: 0.8~1.2Mpa

RoHS Product

340C ~370C. Time : 3-5S.

350C ~370C. Speed : 15-17 mm/s.

330C ~360C. Time : 3-6S. Press: 0.8~1.2Mpa

4.3.1 If soldering flux is used, be sure to remove any remaining flux after finishing to soldering

operation (This does not apply in the case of a non-halogen type of flux). It is recommended that you protect the LCD surface with a cover during soldering to prevent any damage due to flux spatters.

4.3.2 When soldering the electroluminescent panel and PC board, the panel and board should not be detached more than three times. This maximum number is determined by the temperature and time conditions mentioned above, though there may be some variance depending on the temperature of the soldering iron.

4.3.3 When remove the electroluminescent panel from the PC board, be sure the solder has completely melted, the soldered pad on the PC board could be damaged.

4.4 Precautions for Operation 4.4.1 Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust

VLCD to show the best contrast. 4.4.2 It is an indispensable condition to drive LCD's within the specified voltage limit since the

higher voltage then the limit cause the shorter LCD life. An electrochemical reaction due to direct current causes LCD's undesirable deterioration, so that the use of direct current drive should be avoided.

4.4.3 Response time will be extremely delayed at lower temperature than the operating temperature range and on the other hand at higher temperature LCD's show dark color in them. However those phenomena do not mean malfunction or out of order with LCD's, which will come back in the specified operating temperature.

4.4.4 If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it is turned off and then back on.

4.4.5 A slight dew depositing on terminals is a cause for electro-chemical reaction resulting in terminal open circuit. Usage under the maximum operating temperature, 50%RH or less is required.

4.4.6 Input logic voltage before apply analog high voltage such as LCD driving voltage when power on. Remove analog high voltage before logic voltage when power off the module. Input each signal after the positive/negative voltage becomes stable.

4.4.7 Please keep the temperature within the specified range for use and storage. Polarization degradation, bubble generation or polarizer peel-off may occur with high temperature and high humidity.

4.5 Safety

4.5.1 It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned.

4.5.2 If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash

off thoroughly with soap and water.



4.6 Limited Warranty

Unless agreed between and the customer, will replace or repair any of its LCD modules which are found to be functionally defective when inspected in accordance with LCD acceptance standards (copies available upon request) for a period of one year from date of production. Cosmetic/visual defects must be returned to within 90 days of shipment. Confirmation of such date shall be based on data code on product. The warranty liability of limited to repair and/or replace on the terms set forth above.

will not be responsible for any subsequent or consequential events.

4.7 Return LCM under warranty 4.7.1 No warranty can be granted if the precautions stated above have been disregarded. The

typical examples of violations are :

4.7.1.1 - Broken LCD glass.

4.7.1.2 - PCB eyelet is damaged or modified.

4.7.1.3 -PCB conductors damaged.

4.7.1.4 - Circuit modified in any way, including addition of components.

4.7.1.5 - PCB tampered with by grinding, engraving or painting varnish.

4.7.1.6 - Soldering to or modifying the bezel in any manner.

4.7.2 Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned

with sufficient description of the failures or defects. Any connectors or cable installed by the customer

must be removed completely without damaging the PCB eyelet, conductors and terminals.

PACKING SPECIFICATION

Please consult our technical department for detail information. PRIOR CONSULT MATTER

1 For Multi-Inno standard products, we keep the right to change material, process ... for improving the product property without prior notice to our customer.

2 For OEM products, if any changes are needed which may affect the product property, we will consult with our customer in advance.

3 If you have special requirement about reliability condition, please let us know before you start the test on our samples.

Multi-Inno Multi-Inno

Multi-InnoMulti-Inno

Multi-InnoMulti-Inno



r61526_spec

Documents