Component Checklist Installation Instructions A. Use this configuration with a standard 50mm pole (No inserts required) B. Use this configuration with a Visidec 42mm extrusion pole C. Use this configuration with a standard 42mm pole Step 1. Install Quickshift Donut 42mm Front Donut Insert (x1) Visidec Groove Lock (x1) 42mm Rear Donut Insert (x1) 5mm Allen Key (x1) Hardware Mounting Screws M4x10mm Screw (x4) M4x12mm Screw (x4) M4x16mm Screw (x4) Select your correct product configuration: A, B, or C. Rear Donut Insert Rear Donut Insert Front Donut Insert Front Donut Insert Groove Insert Check you have received all parts against this Component Checklist prior to installation. 3mm Allen Key (x1) Slide the Quickshift Donut onto the pole (with the lever open), removing the End Cap if necessary. Rear groove insert must align with slot in the Pole. (Visidec 42mm pole shown) TIGHTEN LOOSEN Once in place, close the lever to lock the Quickshift Donut in the desired position. Slide the Quickshift Donut into the desired position. If necessary, adjust the tension between the Quickshift Donut and the Pole using the 5mm Allen Key supplied. Slot OR OR Groove Insert Security Screw (x1) (optional) CLOSE WARNING: Be careful not to overtighten ! The Spacedec Display Quickshift Donut is to be used on 42mm and 50mm diameter poles only. ! The Manufacturer accepts no responsibility for incorrect installation. NOTE: Phillips-head screwdriver not supplied Display | Quickshift Donut Quickshift Donut (x1) Note: Ensure inserts are fitted in correct orientation. Arrows point to top surface SD-DO
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Component Checklist
Installation Instructions
A. Use this configuration with a standard 50mm pole(No inserts required)
B. Use this configuration with aVisidec 42mm extrusionpole
C. Use this configuration with astandard 42mm pole
Step 1. Install Quickshift Donut
42mm Front Donut Insert (x1)
Visidec GrooveLock (x1)
42mm Rear Donut Insert (x1)
5mm AllenKey (x1)
Hardware MountingScrews
M4x10mmScrew (x4)
M4x12mmScrew (x4)
M4x16mmScrew (x4)
Select your correct product configuration: A, B, or C.
Rear Donut Insert
Rear Donut InsertFront Donut
InsertFront Donut
InsertGrooveInsert
Check you have received all parts against this Component Checklist prior to installation.
3mm AllenKey (x1)
Slide the Quickshift Donut onto the pole(with the lever open), removing the EndCap if necessary.Rear groove insert must align with slot inthe Pole.
(Visidec 42mm pole shown)
TIGHTEN
LOOSEN
Once in place, close the leverto lock the Quickshift Donutin the desired position.
Slide the Quickshift Donut into the desired position.If necessary, adjust the tension between theQuickshift Donut and the Pole using the 5mm AllenKey supplied.
Slot
OR OR
GrooveInsert
SecurityScrew (x1)(optional)
CLOSE
WARNING: Be careful not to overtighten
! The Spacedec Display Quickshift Donut is to be used on 42mm and 50mm diameter poles only.! The Manufacturer accepts no responsibility for incorrect installation.
NOTE: Phillips-headscrewdriver not supplied
Display | Quickshift Donut
QuickshiftDonut (x1)
Note: Ensure inserts are fittedin correct orientation.
Position your Display to the desired viewing angle, using the 40°angular movement allowed by the VESA Ball Mount.
Depending on the weight of the display, it may be necessary to makeadjustments to the VESA Ball Mount. If the display does not hold its position, or is too resistant, adjust the Tension Plate located at therear of the VESA Ball Mount (see diagram right).
To make any adjustments tension evenly using the 3mm Allen Key supplied. Apply half a turn at a time to each screw on the TensionPlate to adjust evenly.
Check the display, and then adjust again if necessary.
Installation Complete
Step 4. Attach your Display to the Quickshift Donut
Press and hold the Release Buttons (one on either side).
ReleaseButton
Whilst holding the Release Buttons, remove the VESA Plate.
LIFT
TIGHTEN
Hook the top of the VESA plate onto the Quickshift Mount.
(optional) Insert the Security Screw, and tighten using a Phillips-head Screwdriver.
Back of Display
VESA Plate
Loosen (-Kg)
Tighten (+Kg)
ReleaseButtons
3mm Allen Key
TensionPlate
Step 3. Attach the VESA plate to your Display
There are two mounting hole configurations:• 75 x 75mm• 100 x 100mm
Choose appropriate Mounting Screwsfrom the Hardware supplied to suityour Display. Top of
Display
Mounting Screws (x4)
VESA Plate
Back of Display
75mm(3”) 100mm
(4”)75mm
(3”)100mm
(4”)
VESA plate
Phillips-headScrewdriver
ReleaseButton
Press and hold the Release Buttons. Gentlyinsert bottom of VESA Plate into QuickshiftMount. ReleaseButtons to lockin place.