Quick Installation Guide EC700-BT€¦ · • EC700-BT System Unit • Screw pack for SATA drive installation • Screw pack for Mini PCIe installation Package Contents. uick Installation

www.dfi.com

1

USB 3.0

COM 1 COM 2 COM 4/8-bit DIOHDMI

Reset

Power

AntennaHole

AntennaHole HDD LED

Status LED

AntennaHole

COM 3 VGA*

DC-in

LAN 1 LAN 2USB 2.0

Grounding

Quick Installation GuideEC700-BT

DFI reserves the right to change the specifications at any time prior to the product's release. This QIG may be based on editions that do not resemble your actual products. For the latest revision and more details of the installation procedure, please refer to go.dfi.com/EC700-BT or scan the QR code on the right.

Panel

Front View

Back View

Note:This port can be in VGA or DVI-I.

• EC700-BT System Unit

• Screw pack for SATA drive installation

• Screw pack for Mini PCIe installation

Package Contents

2Quick Installation Guide |

Installing a 2.5" SATA Drive1. Locate the SATA drive bay on the system board. Unplug the SATA power and data cable, and

remove the 4 mounting screws that secure the HDD bracket to the system board.

2. Connect the SATA cable to the SATA drive first before affixing the SATA HDD on the bracket. Align the mounting holes of the SATA drive with the mounting holes on the HDD bracket and use the 3 provided mounting screws to secure the drive in place. Note that you should install the drive by affixing only 3 screws to the desired screw holes indicated in the picture below.

Mounting Screws (4x)

SATA drive baySATA power cable

SATA data cable

Mounting Screws (3x)

Mounting Screw

2.5" SATA drive

3

21

No Screw

3Quick Installation Guide |

3. Place the SATA drive with the HDD bracket back into the chassis. Secure the SATA drive bay with the mounting screws you removed in step 1. Then connect the SATA data and power cable to the connectors on the system board.

Mounting Screw

SATA power cable

SATA power connector

SATA data cable

SATA connector

Mounting Screw

4Quick Installation Guide |

Board Layout and Jumper Settings

933-EC7000-010GA33134944

TOP BOTTOM

SATA 1

14 SATAPower

LAN 1

LAN 2

DDR3LDDR3LDDR3LDDR3L

Mini PCIe

COM 4

1210

31JP22 1

1

1

(JP20)(JP18)(JP17)

(JP21)

1 3

1210

COM 2

COM 1USB 0

USB 3.0

HDMI

Res

et

Power

3940

2 1

LVDS LCDPanel

DC-in

USB 2

USB 7

USB 1

USB 6

COM 3

Mic-in

1Battery

Buzzer

1

ChassisIntrusion

1Clear CMOS Data (JP24)

SPIFlashBIOS

eMMC(optional)

iTEIT8528E

Mini PCIe mSATA

MicroSD(optional)

1

System Fan

1

USB 0PowerSelect(JP5)

11

2 10

9

COM 6

1

10

9COM 5

1 1

USB 1-2Power Select (JP6)

USB 5-7 PowerSelect (JP7)

1

2 10

9

USB 5

(JP25)

USB 2.0

USB 2.0

(JP17)(JP20)

COM 4/DIO Select (JP22, JP21)

Digital I/O 0-3 Output State Digital I/O Power Select

Auto Power-on Select

1

(JP18)Digital I/O 4-7 Output State

1

VGA/DVI-I

4

SATA 2.0

DDR3LDDR3LDDR3LDDR3LDDR3L

Intel Atom

E3800 Series

IntelWGI210AT

NuvotonNCT6106D

ASMediaASM1442

IntelWGI210AT

SMSCUSB4604

SIM Card

NXPPTN3460

StandbyPower LED

Clear CMOS Data JP24 Normal (default) 1-2 On

Clear CMOS Data 2-3 On

Auto Power-on Select JP25 Power-on via power button (default) 1-2 On Power-on via AC power 2-3 On

Digital I/O Output State JP18 (DIO 4-7) JP20 (DIO 0-3) GND (default) 1-2 On +5V or +5V_standby 2-3 On

Digital I/O Power Select JP17 +5V_standby 1-2 On +5V (default) 2-3 On

COM 4/DIO Select JP21, JP22

COM 4 (default) 1-2, 4-5 7-8, 10-11 On

DIO2-3, 5-6 8-9, 11-12 On

USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7) +5V_standby (default) 1-2 On

+5V 2-3 On

Note: You cannot use COM 4 and DIO at the same time. Please set up JP21 and JP22 together.