-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
QK-G025 GSM Remote Controller--- DC Motor Remote Control
Features Control DC Motor (Two Directions) through
Free Call Using Caller ID for Identification,
Callers will be Ignored Two Working Mode: Dead Man
Pulsed Alternating or Fixed Direction setting by SMS Easy to
Install and Configuration (No PC
required) Up to 4 Mobile Phones per Unit Request Status via SMS
Compatible with All Major GSM Tri-band GSM for Use in Europe &
U
elec.com 1 of 10
G025 GSM Remote Controller Application NoteDC Motor Remote
Control Dialer
Applications
Control DC Motor (Two Directions) through
dentification, Unknown
ead Man and Time
Alternating or Fixed Direction setting by SMS Easy to Install
and Configuration (No PC
GSM SIM Networks se in Europe & USA
Electric Doors, Shutters, Garages Electronic Certain/Blinds DC
Motors, Actuators Plant Maintenance Valve Control Pumping Station
Oil/gas Pipelines Control Security System PLC and Automation
System
2015
Application Note Dialer
Electric Doors, Shutters, Garages
System
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
Documents History Issue Date Changes / Comments
1.0 23-02-2015 Initial release
Order Information
Part No
QK-G025 GSM Remote Controller (DC Motor Control)
QK-G025S QK-G025 GSM DC Motor Remote
Contents
1 INTRODUCTION ................................
2 PREPARING SIM CARD
3 HARDWARE................................
3.1 MODULE ................................3.2 POWER
CONNECTIONS3.3 ALARM FUNCTION AND 3.4 SIM CARD SLOT
................................3.5 ENCLOSURE
................................
4 CONFIGURATION ................................
5 COMMAND AND RESPONSE
6 OPERATING SPECIFICATIONS
1 INTRODUCTION
QK-G025 module is an industrial grade any DC powered devices. It
allows operators to control remote equipments, machines by free
cafour mobile phone numbers (SIM card numbers) can be registered
with belong to families/ technicians or engineers who have the
reqdevices. Just dial from the registeredthe machine will be turned
on/offanswer the call and it will immediately
---- Four control mobile phones. One main control terminal and
up to 3 additional control terminals can be registered with
--- Two digital alarm inputs. Various sensors can be
monitoreddetector, position sensitive detector, motion sensor,
temperature/wind detector, carbon dioxide detector, water leak
detector.
--- The DC motor output can be set as DeTime mode(action time is
set as a fixed time).
--- The DC motor output can be
--- Keep SIM alive all time by sending status SMS every set
elec.com 2 of 10
Changes / Comments
Initial release
Description
GSM Remote Controller (DC Motor Control) module
SM DC Motor Remote Controller with enclosure
................................................................................................
PREPARING SIM CARD
................................................................................................
................................................................................................
................................................................................................ONNECTIONS................................................................................................NCTION
AND DIGITAL INPUT CONNECTION ................................
................................................................................................................................................................................................
................................................................................................
COMMAND AND RESPONSE SMS
................................................................
ATING SPECIFICATIONS
................................................................
industrial grade product intended to provide remote control
of
It allows operators to control remote equipments, machines by
free call through GSM network. Up to mobile phone numbers (SIM card
numbers) can be registered with it. These mobile phones can
belong to families/ technicians or engineers who have the
requirements to control corresponding the registered SIM cards then
the barriers or doors will be opened
off. There are no call costs since this GSM control
moduleimmediately take action after identifying the registered SIM
card number
Four control mobile phones. One main control terminal and up to
3 additional control terminals can be registered with QK-G025.
ital alarm inputs. Various sensors can be monitored, e.g.,
photocell receiver, obstacle detector, position sensitive detector,
motion sensor, temperature/wind detector, carbon dioxide detector,
water leak detector.
he DC motor output can be set as Dead Man mode (action during
dialing period) or Pulsed Time mode(action time is set as a fixed
time).
The DC motor output can be fixed polarity or
alternating(polarity changed alternatively)
by sending status SMS every set days(between 28 to 99 days)
2015
................................................... 2
....................................... 3
.......................................................... 3
.............................................................. 3
......................................... 5
...............................................................
5 ................................................... 6
........................................................ 6
................................................ 8
..................................................... 8
........................................................ 10
remote control of DC motors or
ll through GSM network. Up to . These mobile phones can
uirements to control corresponding doors will be opened/closed,
or
module will not SIM card numbers.
Four control mobile phones. One main control terminal and up to
3 additional control
photocell receiver, obstacle detector, position sensitive
detector, motion sensor, temperature/wind detector, carbon
dioxide
ad Man mode (action during dialing period) or Pulsed
changed alternatively).
days(between 28 to 99 days)
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
2 PREPARING SIM CARD
All new SIM cards have to be registered with the network
provider before they can be used, usually by calling the network
provider or registering online supplied with your SIM card.
After successfully registering the SIM card, ensure there is
sufficient credit on the card for programming confirmation texts to
be sent from QKdisabled from the SIM card before inserting it into
QKstatus of your SIM card, place the card in an unlocked mobile
phone, switch the phone on. If call can be made without entering a
PIN number
Lastly, please disable any voicemail that is set up on the SIM
card and keep Caller ID function available. By now, the SIM card is
now ready to use.
It is recommended that if a pay as you go (PAYG) SIM
cardautomatically Top-Up when the cards credit falls below a
certain limit. Some of PAYG SIM cards will be de-activated by the
network if not used to make an outgoing voice call or send an SMS
text message within a specific period. To prevent this simply avoid
SIM card been de-activated.
3 HARDWARE
3.1 Module
General view of the module are show as below and details of each
function parts are described from the next section.
elec.com 3 of 10
Figure 1 System diagram
CARD
All new SIM cards have to be registered with the network
provider before they can be used, usually by calling the network
provider or registering online please refer to the instructions
supplied with your SIM card.
After successfully registering the SIM card, ensure there is
sufficient credit on the card for programming confirmation texts to
be sent from QK-G025 module. The PIN request disabled from the SIM
card before inserting it into QK-G025 module. To check the PIN
request status of your SIM card, place the card in an unlocked
mobile phone, switch the phone on. If
without entering a PIN number, then the PIN request is
disabled.
Lastly, please disable any voicemail that is set up on the SIM
card and keep Caller ID function available. By now, the SIM card is
now ready to use.
recommended that if a pay as you go (PAYG) SIM card been used
please choose to Up when the cards credit falls below a certain
limit. Some of PAYG SIM
activated by the network if not used to make an outgoing voice
call or send an SMS text message within a specific period. To
prevent this simply use set alive SIM message to
activated.
General view of the module are show as below and details of each
function parts are described
2015
All new SIM cards have to be registered with the network
provider before they can be used, please refer to the
instructions
After successfully registering the SIM card, ensure there is
sufficient credit on the card for he PIN request should be To check
the PIN request
status of your SIM card, place the card in an unlocked mobile
phone, switch the phone on. If a t is disabled.
Lastly, please disable any voicemail that is set up on the SIM
card and keep Caller ID function
please choose to Up when the cards credit falls below a certain
limit. Some of PAYG SIM
activated by the network if not used to make an outgoing voice
call or send an alive SIM message to
General view of the module are show as below and details of each
function parts are described
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
Figure
GSM aerial
SIM card holder
Network LED
System LED
elec.com 4 of 10
Figure 2 General view of the control module (V1.1)
GND GND P1 P2
INT2 INT1 1224VDC
2015
P2
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
Figure
3.2 Power Connections
QK-G025 module can be powered by 12above, up to 24V) to the
power screw terminals. The red power LED will flash 1 second
interval once system finish initialization. The blue network LED
indicator will initially flash quicklylogged onto the network it
will flash more slowly approximately once every 3 to 4 seconds.
3.3 Alarm function and Digital input connection
QK-G025 has two external monitoring/alarm input connectors.
Various sensors can be connected to it, e.g., photocell receiver,
obstasensor, temperature/wind detector, carbon dioxide detector,
water leak detector.
In the case any of these connected sensor/detectors are
triggered and send the low level signal (0V) to QK-G025,
QK-G025
There are two typical ways to connect the external alarm inputs
to device can be used as switches or a input source for INT1/INT2
of
elec.com 5 of 10
Figure 3 QK-G025 mechanical drawing (V1.1)
Power Connections
module can be powered by 12 to 24VDC. Connect a DC power supply
from 12V (or above, up to 24V) to the power screw terminals. The
red power LED will flash 1 second interval once system finish
initialization. The blue network LED indicator will initially flash
quickly
o the network it will flash more slowly approximately once every
3 to 4 seconds.
Alarm function and Digital input connection
has two external monitoring/alarm input connectors. Various
sensors can be connected to it, e.g., photocell receiver, obstacle
detector, position sensitive detector, motion sensor,
temperature/wind detector, carbon dioxide detector, water leak
detector.
In the case any of these connected sensor/detectors are
triggered and send the low level signal G025 will disable the
output of P1 and P2 immediately.
There are two typical ways to connect the external alarm inputs
to QK-G025device can be used as switches or a input source for
INT1/INT2 of QK-G025
2015
24VDC. Connect a DC power supply from 12V (or above, up to 24V)
to the power screw terminals. The red power LED will flash 1 second
interval once system finish initialization. The blue network LED
indicator will initially flash quickly. Once
o the network it will flash more slowly approximately once every
3 to 4 seconds.
has two external monitoring/alarm input connectors. Various
sensors can be cle detector, position sensitive detector,
motion
sensor, temperature/wind detector, carbon dioxide detector,
water leak detector.
In the case any of these connected sensor/detectors are
triggered and send the low level signal l disable the output of P1
and P2 immediately.
G025. External alarm G025 module.
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
Figure
3.4 SIM card slot
The SIM card should be inserted into SIM card slot before
applying the power. Most 3V SIM card can proper working with after
power up. Network LED flashes at 1Hz after registration
completed.
3.5 Enclosure
IP56 Insulation Class 2 plastic enclosure, 115mm*90*40 external
dimension is used for QKG025.
elec.com 6 of 10
Figure 4 External alarm device connecting methods
The SIM card should be inserted into SIM card slot before
applying the power. Most 3V SIM card can proper working with
QK-G025 module. The registering can take up to few minutes after
power up. Network LED flashes at 1Hz after registration
completed.
IP56 Insulation Class 2 plastic enclosure, 115mm*90*40 external
dimension is used for QK
Figure 5 Enclosure drawing
2015
The SIM card should be inserted into SIM card slot before
applying the power. Most 3V SIM module. The registering can take up
to few minutes
IP56 Insulation Class 2 plastic enclosure, 115mm*90*40 external
dimension is used for QK-
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
Figure
elec.com 7 of 10
Figure 6 GK-G025 (with enclosure)
Figure 7 GK-G025 (with enclosure) back view
2015
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
4 CONFIGURATION
The following is required to configure QK
--- Insert SIM card into controller box
--- Power up and waiting for the blue Ldepends on the network
situation.
--- Send 888888 as SMS to QK-Quark-elec products. Your Main
phone has been registered.
--- If additional mobile terminals needed send BDn(mobile
terminal number)F to QKUp to 3 additional terminals can be
configured. and check additional SIM card numbers. The it is
indexed in the registered SIM numbers,
--- GK-G025 supports two working modes: Dead Man and PulsedTime
mode, the DC motor outputs Dead Man mode, it will keep the active
status until hang up. three different polarity ways,
corresponding
--- clockwise way
--- Anti-clockwise way
--- Alternating direction way.
--- If the module was set to work on
By now, QK-G025 is ready for using. Details about the SMS
command and response SMS can be found in the next section.
5 COMMAND AND RESPONSE
Remember that all SMS text commands must always be sent using
CAPITAL LETTERS. DO NOT add spaces or any other characters in the
SMS.
Function
Register myself as main SIM number
888888
Register additional SIM numbers
BDn(mobile number)F
n=1 for 1st mobile terminals
n=2 for 2nd mobile terminals
n=3 for 3terminals
elec.com 8 of 10
The following is required to configure QK-G025 for the first
time using.
Insert SIM card into controller box.
Power up and waiting for the blue LED flashing slowly. It
normally takes about 1 to 2 minutes depends on the network
situation.
-G025 controller, if successfully, you should receive Thanks for
using elec products. Your Main phone has been registered.
If additional mobile terminals needed send BDn(mobile terminal
number)F to QKUp to 3 additional terminals can be configured.
Operator can use the main terminal to register, delete and check
additional SIM card numbers. The QK-G025 controller can verify the
incoming numbers, if it is indexed in the registered SIM numbers,
it will execute the actions.
025 supports two working modes: Dead Man and Pulsed Time. When
it working on outputs active for a fixed setting time and then
stop. While working on
an mode, it will keep the active status until hang up. Each
mode, QK-G025 can be set on corresponding to three different
running directions of DC motor:
Alternating direction way.
work on Pulsed Time mode, please ensure the working time
G025 is ready for using. Details about the SMS command and
response SMS can be
OMMAND AND RESPONSE SMS
Remember that all SMS text commands must always be sent using
CAPITAL LETTERS. DO NOT characters in the SMS.
Command Note
Register SIM cards
888888 Register the main mobile terminal with QKG025 module by
sending 888888 to QKG025 model.
The module will reply with Thanks for using Quark-elec products.
Your Main phone has been registered. if registration successful.
One QK-G025 module can only have one main registered SIM card
number.
BDn(mobile number)F
n=1 for 1st mobile terminals
n=2 for 2nd mobile terminals
n=3 for 3rd
mobile terminals
Once the main mobile terminal registered with QK-G025, it can
pair another three mobile terminals with QK
For example, by sending BD107919157124F, the first mobile
terminal (number is 0791915been paired with QKBD207909135124F,
means to pair QKG025 with the second terminals (number is
07909135124).
Message Your No n phone has been registered will be replied by
QK
2015
ED flashing slowly. It normally takes about 1 to 2 minutes
G025 controller, if successfully, you should receive Thanks for
using
If additional mobile terminals needed send BDn(mobile terminal
number)F to QK-G025 controller. Operator can use the main terminal
to register, delete
verify the incoming numbers, if
Time. When it working on Pulsed and then stop. While working
on
G025 can be set on to three different running directions of DC
motor:
ime mode, please ensure the working time has been set.
G025 is ready for using. Details about the SMS command and
response SMS can be
Remember that all SMS text commands must always be sent using
CAPITAL LETTERS. DO NOT
Note
Register the main mobile terminal with QK-by sending 888888 to
QK-
The module will reply with Thanks for products. Your Main
phone has been registered. if registration G025 module can
only
have one main registered SIM card
Once the main mobile terminal registered G025, it can pair
another three
mobile terminals with QK-025.
For example, by sending BD107919157124F, the first mobile
terminal (number is 07919157124) has been paired with QK-025.
Similar, BD207909135124F, means to pair QK-G025 with the second
terminals (number is
Message Your No n phone has been registered will be replied by
QK-G025, if
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
Delete additional SIM numbers
DELn
n=1 for 1
n=2 for 2terminals
n=3 for 3terminals
Check registered SIM numbers
WHORED
Switching Relay & Mode checking
Set alive time(Keep SIM alive text)
SIMALIVEnn
Where 28number beyond this scale means close this function.
The factory default setting is SIMALIVE00, which means this
function is
Set the working mode in Dead Man mode
mode
modedirection
modedirection
Set the working mode in Pulsed Time mode
mode(alternating direction)
(fixed clockwise direction)
(fixed anti
Set the working time in pulsed time mode
PTDnn
Where 03
Check relay working mode
RMODE
elec.com 9 of 10
the n mobile terminal successfully paired.
DELn
n=1 for 1st mobile terminals
n=2 for 2nd
mobile terminals
n=3 for 3rd
mobile terminals
The registered SIM cards can be deleted from the authorized SIM
list by sending DELn. The deleted SIM terminals cannot control
QK-G025 any longer.
WHORED QK-G025 will reply with the authorized SIM list in the
following format:
No.1 SIM is xxxxxxxx; No.2 SIM is xxxxxxxx; No.3 SIM is
xxxxxxxx.
Switching Relay & Mode checking
SIMALIVEnn
Where 28nn99. Any input number beyond this scale means close
this function.
The factory default setting is SIMALIVE00, which means this
function is disabled.
QK-G025 will reply with the authorized SIM list in the following
format:
QK-G025 will send heatbeat SMS message every nn days.
DMM: Dead Man mode(alternating direction)
QK-G025 will reply with the authorized SIM list in the following
format:
QK-G025 has been set working in Dead Man mode (Alternating/
fixed clockwise/ fixed anti-clockwise direction).
CLM: Dead Man mode(fixed clockwise direction)
ANM: Dead Man mode(fixed anti-clockwise direction)
PTM: Pulsed Time mode(alternating direction)
QK-G025 will reply with the authorized SIM list in the following
format:
QK-G025 has been set working in Pulsed Time mode
(Alternating/fixed clockwise/fixed antidirection).
GZY: Pulsed Time mode fixed clockwise direction)
GFY: Pulsed Time mode fixed anti-clockwise direction)
PTDnn
Where 03nn99.
QK-G025 will reply with the relay state information as the
following format:
QK-G025 is working in pulsed time mode and the setting time is
nn seconds.
RMODE QK-G025 will reply with the relays working mode
information with the following format:
2015
the n mobile terminal successfully paired.
The registered SIM cards can be deleted from the authorized SIM
list by sending DELn. The deleted SIM terminals cannot
G025 any longer.
G025 will reply with the authorized SIM list in the following
format:
No.1 SIM is xxxxxxxx; No.2 SIM is xxxxxxxx; No.3 SIM is
xxxxxxxx.
G025 will reply with the authorized SIM list in the following
format:
will send heatbeat SMS message every nn days.
G025 will reply with the authorized SIM list in the following
format:
G025 has been set working in Dead (Alternating/ fixed
clockwise/
clockwise direction).
G025 will reply with the authorized SIM list in the following
format:
G025 has been set working in Pulsed Time mode (Alternating/fixed
clockwise/fixed anti-clockwise
G025 will reply with the relay state information as the
following format:
G025 is working in pulsed time mode and the setting time is
nn
G025 will reply with the relays working mode information with
the
-
Quark-Elec Application Note
http://www.quark-elec.com
V1.0
QK-G025 has two digital input ports. It can be used to monitor
the external signals. These input ports accept 0V to 5V voltage
level. In the case any of the input voltage level below 1.0V, the
DC motor output will be disabled.
6 OPERATING SPECIFICATIONS
Item
Frequency bands
SMS
Operating temperature
Storage temperature
DC supply
Average supply current (typical quiescent) Maximum supply
current(during SMS transceiver activity)
GSM receive sensitivity
GSM transmitting power
DC motor output voltage
DC motor output maximum current
For more technical information and enquires please go to Quark
http://quark-elec.com/forum/ For sales and purchasing information,
please email us:
Quark Electronics (UK)
elec.com 10 of 10
QK-G025 is working in xx (xx means one of the six modes which
has been setup.
Monitoring/Alarm Input
has two digital input ports. It can be used to monitor the
external signals. These input ports accept 0V to 5V voltage level.
In the case any of the input voltage level below 1.0V, the DC
motor
PECIFICATIONS
Specification
Quad-band: GSM850, EGSM 900 DCS1800, PCS1900.
MT, MO, CB, Test and PDU mode
-25C to +80C
-40C to +85C
12 to 24VDC
40mA
Maximum supply current(during SMS 600mA
-107dBm
Class 4(2W) at GSM850, EGSM 900. Class 1(1W) at DCS1800,
PCS1900. 12DC to 24DC
current 30A
For more technical information and enquires please go to
Quark-elec forum:
For sales and purchasing information, please email us:
[email protected]
Quark Electronics (UK)
24 Meadowbank Hitchin
Herts. UK SG4 0HY
2015
G025 is working in xx (xx means one of the six modes which has
been
has two digital input ports. It can be used to monitor the
external signals. These input ports accept 0V to 5V voltage level.
In the case any of the input voltage level below 1.0V, the DC
motor
band: GSM850, EGSM 900 DCS1800, PCS1900.
elec forum:
elec.com