Quadcopter - Horizon Hobby · QUADCOPTER SENSOR CALIBRATION If the quadcopter is constantly drifting in the same direction or any time a new fl ight control board has been installed,

BEFORE FLYING, PLEASE READ & UNDERSTANDTHESE INSTRUCTIONS!

Vista FPV V2 Quadcopter

Flight Battery

Spare Blades(2 black, 2 color)

AAA Batteries (4)

Controller

Camera WireCamera with

Memory Card

USB Charger

Radio ControlledQuadcopter

LITHIUM BATTERY WARNING This product includes a lithium polymer (LiPo)

battery. Improper handling could result in FIRE!

A lithium battery fire has the potential to ignite

surrounding areas and may cause property

damage or cause personal injury.

For safe LiPo handling, follow all of these guidelines:

● ALWAYS keep out of reach of children! ● NEVER charge a LiPo battery on a flammable surface or near

combustible materials. ● NEVER charge inside a vehicle or at a location that could be

damaged in the event of a LiPo fire.● NEVER charge or use a battery that is deformed, bent, crushed

or has any type of visible damage.● ALWAYS use the included, factory-approved charger with this

LiPo battery.● ALWAYS keep a supply of sand accessible when charging.

Dumping sand on the battery will assist in extinguishing a LiPo

chemical fire.● MOST IMPORTANT! NEVER leave the charger and LiPo battery

unattended while charging. ● It is normal for the charger to become warm to the touch. However,

disconnect the battery and unplug the charger immediately if

either becomes hot, begins to swell, or smoke!● ALWAYS disconnect the battery and unplug the charger if the

charge time exceeds 3 hours.● ALWAYS disconnect the battery and unplug the charger after

the charge is complete. ● ALWAYS disconnect and remove the battery from your model

immediately following operation.● ALWAYS store/transport LiPo batteries in a fireproof container

away from combustible materials. ● NEVER put a LiPo battery in the pocket of any clothing.● Keep LiPo batteries out of reach of animals. A punctured battery

may cause a fire.● NEVER use the included charger for any other battery other than

the one included with this model.

● In the event of a crash, ALWAYS place the battery into a fireproof

container immediately. Examine the battery for damage before

further use.● ALWAYS operate and store batteries between 40-110° F (4-43° C).● NEVER allow the battery temperature to exceed 140° F [60° C]

during operation.● NEVER disassemble or modify a battery, its wiring, or puncture

cells, as this may result in fire.● NEVER allow the battery to short circuit by touching exposed

wires together.● ALWAYS stop the operation of your model immediately when the

battery power is low. A battery failure can occur when attempting

to recharge an over-discharged battery.● LiPo batteries must always be recycled or disposed of properly.● If you are unable to follow these guidelines, return this product

to the place of purchase.

SAFETY PRECAUTIONS Follow these safety precautions when operating the Vista FPV V2:

• Adult supervision required.

• Do not touch the spinning blades or fly over people or animals.

• Keep your face and body as well as all spectators away from

the rotors whenever the battery is connected.

• Stay clear of buildings, trees and power lines. AVOID flying in

or near crowded areas. DO NOT fly close to people, children

or pets.

• Maintain a safe pilot-to-drone distance while flying.

• Your Vista drone should not be considered a toy, but rather

a small, working model. If not operated correctly, the model

could possibly cause injury to you or spectators and damage

to property.

• Do not alter or modify the model, as doing so may result in an

unsafe or unflyable model.

• You must check the operation of the model before every flight

to ensure that the model has remained structurally sound.

CAUTION: Changes or modifications to this product not expressly

approved by the party responsible for compliance may void the

user’s authority to operate the equipment.

TO PREVENT MOTOR DAMAGE ALWAYS BE SURE THE THROTTLE IS

OFF WHEN THE BLADES ARE OBSTRUCTED OR CONTROL IS LOST.

CHARGING

Plug the charger into a USB port or AC adapter (not included) as shown and connect

the battery. The charger LED is steady on when charging. The LED flashes when

charge is complete.

NEVER leave the battery unattended while charging.

● DO NOT allow the USB port to power down while the charger is connected

to the battery.

● ALWAYS unplug the charger from the USB port and the battery when

charging is complete.

● NEVER charge a puffed or damaged battery.

INSTALL BATTERIES IN THE CONTROLLER

Remove the screw and slide the cover

down to insert the included 4 AAA

batteries.

INSTALL THE CAMERA

1. Carefully slide the camera onto the camera mount until you feel it click into

place.

2. Connect the included camera wire to the camera and to the quadcopter. The

plugs can only be connected one way. Look closely at the photos to see the

orientation of wire colors.

LINKING 1. Turn on the controller with the throttle at its

lowest position.

2. Connect the battery to the Vista and place it on a level surface. The LED on the quad will flash rapidly when the quad is linked to the controller and ready to fly.

QUADCOPTER SENSOR CALIBRATIONIf the quadcopter is constantly drifting in the same direction or any time a new fl ight

control board has been installed, the sensors on the Vista should be calibrated.

1. Calibrate the sensors before the fi rst fl ight. Center all the trim adjustments.

To center the trim settings, hold down one side of the trim button until you

hear a long beep. If the controller stops beeping, release the trim button

and hold down the other side.

2. Place your Vista on a level surface and link the quadcopter with the

controller.

3. Move and hold the right stick in its lower right corner.

4. Move the left stick down and to the right. When the arm LEDs start to fl ash,

release both sticks. The LEDs will stop fl ashing when the calibration is

complete.

2

ALWAYS unplug the

battery after flying!

Damage to the

battery may result if

left connected.

FLYING

FLYING BASICS 1. Take off by “slowly” advancing the left stick until the quad takes off.

2. Control altitude using the left stick.

3. Use the right stick to move left, right, forward, or backward.

4. Use the left stick (left/right) to rotate or spin left or right.

5. Always use small movements until you learn how the model behaves.

TO PREVENT MOTOR DAMAGE ALWAYS BE SURE THE

THROTTLE IS OFF WHEN THE BLADES ARE OBSTRUCTED

OR CONTROL IS LOST.

DUAL RATESControl sensitivity can be changed by pushing in

on the right stick on the controller. The default

is low rate when the flight mode LED is blue.

The controller will make a double beep and the

flight mode LED will change to orange indicating

high rate. This mode should be used when flying

outdoors or when more agility is desired. Pushing

in on the right stick again will return the controller to low rate indicated by a single

beep and the flight mode LED changing back to blue. This mode should be used

when flying indoors, learning to fly, or smoother video is desired.

The low rate sensitivity will always be 25% less than the high rate. The overall

controls can be adjusted by:

1. Pushing in the right stick until the controller beeps once.

2. Continuing to push the right stick in and advancing the throttle to the

desired setting.

3. Releasing the right stick and returning the throttle to 0%.

The default setting is when the throttle stick is at 50% (midstick).

FLIGHT MODESThe Vista has advanced stabilization

which automatically levels the quad

when the right stick is centered and

limits how far the Vista can tilt.

Press the Flight Mode button to toggle

this off or on.

Easy Mode – Control rates are at a low setting. This is the default mode for the

controller and should be used when indoors or if the pilot is just learning to fl y.

Normal Mode – The control

rates are high. This mode

should be selected when fl ying

outdoors or when more agility

is desired.

Advanced Mode – Advanced stabilization is off and the control rates are low.

Your Vista will be more agile because there are no limits on how far it can turn

in any direction.

Expert Mode – Advanced stabilization is off and the control rates are high.

FLIPSYour Vista can perform a

fl ip when the fl ip button

is pressed followed by

moving the right stick in

the desired fl ip direction.

This stunt needs lots

of room and should

be done outside with

relatively calm winds.

NOTE: When the battery voltage is low (fl ashing LEDs) the fl ip function is disabled.

LOW BATTERY INDICATORThe LEDs on the Vista will fl ash slowly when the LiPo battery voltage is low. The

Vista FPV should be landed as soon as possible to avoid damaging the battery.

Always unplug the battery after fl ight. The battery needs to be charged

before the quadcopter is stored.

The controller will make five quick beeps when the AAA batteries need to

be charged.

MOTOR OVERLOAD PROTECTIONThe Vista is equipped with motor overload protection circuitry

that shuts down the motors in the event the propellers become

blocked by an obstruction and throttle is applied. In order to reset

the overload protection you will need to free the Vista from the

obstruction and lower the throttle to zero. If the overload protection

is triggered repeatedly or late into a fl ight then it may prematurely cause the

low battery indicator to fl ash the LEDs. Disconnect the battery and wait several

seconds before reconnecting it. If the LEDs continue to fl ash then you should

stop fl ying and recharge the battery.

Easy Steady blue ON

Normal Steady orange ON

Expert Flashing orange OFF

Advanced Flashing blue OFF

Mode Tx LED Stab.Low

High

High

Low

Sensitivity

3

RECORDING VIDEO & PICTURES WITHOUT THE APP

1. Insert the memory card into the camera. If you remove or need to replace,

insert as shown with the gold contact points facing up toward the Vista. Push

the card in until it clicks into place. To release the card, push in until it clicks

and the card will spring out of position to be removed. The memory card

should never be inserted or removed from the camera when the battery

is plugged in. When inserting the card, be sure to align the card correctly

into the card slot.

2. Turn on the controller and connect the battery to the Vista. Before taking pictures

or video you must allow the camera 30 seconds to initialize. Pictures or video

taken before the camera has initialized may not be saved to the card or the

file(s) will be corrupted.

3. Use the PICTURE and VIDEO buttons on the controller to take still images and

video recordings. Pressing and releasing the VIDEO button will start video

recording indicated by a long ‘beeeep’ from the controller. Pressing and

releasing the button again will stop recording indicated by a short ‘beep’ from

the controller and the LEDs on the Vista will flash. Pressing and releasing the

PICTURE button on the controller will take a photo indicated by a short ‘beep’

from the controller. Photos can be taken using the PICTURE button on the

controller even if the DroneView camera is recording video. Allow at least 2

seconds after taking a picture before taking another picture.

NOTE: Avoid pressing and holding the video and picture buttons. A quick ‘press

and release’ is sufficient to activate the camera.

BEFORE DISCONNECTING THE BATTERY FROM THE VISTA

AND REMOVING THE MEMORY CARD, YOU MUST ALLOW

AT LEAST 30 SECONDS FOR THE DRONEVIEW CAMERA

TO CLOSE THE FILES. FAILURE TO DO SO MAY RESULT

IN MISSING OR UNREADABLE FILES.

4. Wait at least 30 seconds following the end of the last video recorded. Disconnect

the battery from the Vista, THEN remove the memory card from the camera.

5. Insert the card into a memory card reader (not included) for use with a PC

or tablet. Pictures are saved as .JPG files and videos are saved as .AVI files.

Pictures and videos can be viewed or edited using software that was bundled

with your PC or tablet, or there is a wide variety of software available from

third parties both free and for purchase.

NOTE: The DroneView camera’s maximum video length is 5 minutes. If video

is recorded for longer than 5 minutes the DroneView camera will automatically

close the video file and start a new file. There may be a short loss of video footage

during this switch to a new file. The DroneView will continue to create new video

files every 5 minutes of continuous recording until the memory card becomes

full or the battery is disconnected or the battery voltage drops below the abilty

for the camera to operate. Corrupt or missing files may result in video recording

being stopped in this way. When the battery voltage is low indicated by flashing

LEDs the camera will stop recording and save the video file. Videos and pictures

cannot be taken until the battery is recharged.

6. After you have retrieved your files from the memory card (copy the files you

wish to keep to a safe location) you can delete the files on the memory card.

The DroneView camera will create the sub folders it needs if they are deleted

from the card.

USING THE DRONEVIEW APPThe DroneView app is software for your WiFi-capable Apple or Android device

that allows you to connect to the DroneView camera to use the FPV (First Person

View) function as well as to take videos and pictures and upload and view them

directly to your device.

1. Install the “DroneView” app from Google Play (Android) or the App Store (Apple).

2. Insert the memory card into the camera and connect a charged LiPo battery

to the Vista.

3. iOS Only - Go to the WiFi setting

options in your device and select

the DroneView network. The actual

name of the DroneView network will

vary from the picture shown here. It

may take several seconds for the

DroneView network to appear in the

available network list in proximity

to your device. No password is

needed to connect to the DroneView

network. NOTE: Android devices

will automatically connect to the

DroneView WiFi network when the

DroneView app is opened.

Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and

other countries. App Store is a service mark of Apple Inc. Android™ and Google

Play are trademarks of Google Inc.

Wi-Fi® are Wi-Fi Alliance® are registered trademarks of the Wi-Fi Alliance.

4

4. Grasp your device as shown and attach it to the phone mount on the controller

by pushing up on your phone against the spring loaded top clip until you can

fit the other side into the bottom clip.

5. With your device connected to

the DroneView WiFi network,

open up the DroneView app. It

may take several seconds for the

app to locate and connect to the

DroneView WiFi network.

6. Once connected you will see on your device the image seen by the camera

(referred to in this manual as the FPV feed). Press anywhere on the screen to

pull up the main options.

Picture Button - Press to take a still image. Note: pictures cannot be taken with

the app while recording is in progress.

Video Button – Press to start recording (red stop button appears on right when

recording).

File Gallery Button – Opens gallery to display contents of memory card for

viewing, exporting and deleting.

Settings Button – Opens the setting menu.

NOTE: The FPV feed is for the purposes of displaying what the camera is

recording to improve the quality and accuracy of videos and pictures with respect

to the pilot’s intended field of view. We do not recommend attempting to fly the

Vista relying solely on the FPV feed. Delays in the FPV feed can cause the image

shown in the app to not represent the exact current position of the Vista. Any

interruption of the FPV feed will not be present in the recorded video files. Flying

without maintaining line of sight of the quad is unsafe.

FILE GALLERYOpening the file

gallery displays the

contents of the

memory card in the

c a m e r a . E a c h

thumbnail represents

a picture or video.

Videos have a small

camera icon and the

length of the videos

on the thumbnails.

Pictures can be

viewed by clicking

on the picture

thumbnails. In order

to view videos, you

must first export

them by pressing

Select and then pressing each thumbnail that you wish to export. Press Export to upload the files to your device. Pictures and videos will be copied to your device’s

camera roll. They can also be viewed in the DroneView app by pressing Cancel after the exporting is complete and then pressing the thumbnail you wish to view.

(Android users do not need to press Cancel to view files.)

NOTE: We do not recommend exporting videos that exceed 1 minute in length

because of the amount of time it will take to export the files. For longer videos or

a larger quantity of videos, we recommend removing the memory card from the

camera and transferring the contents directly to a PC using a card reader. If you

do plan to export longer videos, we recommend first charging the Vista battery

to ensure exporting does not become interrupted due to low battery voltage.

Press Export after

you have selected

the files you wish to

export. A progress

window will appear

i n d i c a t i n g t h e

amount of data that

has been exported.

When completed, you

can now press the

video thumbnails to view the videos or you can open your device’s camera roll

(gallery) and view them there. When you have confirmed that the files have been

successfully transferred to your camera roll (gallery) press Select and choose

the files you wish to delete if you no longer want them in the file gallery.

SETTINGSThe settings menu

allows you to change

the WiFi name,

adjust brightness

and contrast, rotate

camera view and

toggle the date code

off and on.

5

Changing the WiFi Name will change how the Camera is identified in the WiFi

network list.

The Brightness and Contrast will adjust the FPV feed display qualities. Video and

picture files will have the same display qualities as the FPV. You may wish to

experiment with these settings depending on lighting conditions and personal

preferences. Press reset to return the brightness and contrast to the default values.

Rotate Camera view will rotate the FPV feed and recorded videos and pictures

180°. This feature is needed when the DroneView camera is used independently

of the Vista with a Power Battery Module (TACZ1002) and is mounted on top of

a surface rather than underneath like on the Vista.

The Date Code will display the current date on the FPV feed when the Date Code

is turned ON. The date will also be seen in video recordings and pictures in the

same format as seen on the FPV feed. The Date Code is automatically updated

to match the date of your device when connected via WiFi network.

If you made any changes in the settings menu then you will be prompted to save

when exiting the settings menu. If you select NO when prompted to save then

the changes will be discarded. iOS Only - If you change the WiFi name then you

will need to exit the DroneView app and select the newly named network in the

WiFi setting options of your device.

USING TWO DEVICES SIMULTANEOUSLYThe DroneView camera can be connected with up to two devices simultaneously.

Two devices will have the ability to connect to the DroneView WiFi network and

share the FPV feed from the camera. Both devices will also be able to take pictures

and start/stop video recording.

NOTE: Exporting can only be done with one device at a time. Attempting to

export files simultaneously from a DroneView camera to two devices may cause

the transfer to freeze.

TROUBLESHOOTINGFLYING PROBLEMSPROBLEM: The Vista will not respond to the controller. SOLUTION: (1) Charge or change the battery in the Vista. (2) Turn off the controller

and disconnect the battery for the Vista. Re-link the Vista and controller.

PROBLEM: Red controller LED light flashing after linking. SOLUTION: Replace with new AAA batteries.

PROBLEM: Unable to flip. SOLUTION: Battery voltage too low.

PROBLEM: Stabilization not working properly. SOLUTION: (1) Battery voltage low. (2) Re-link. (3) Recalibrate the sensors.

PROBLEM: Will not take off. SOLUTION: Rotor blades incorrectly installed. See Blade Replacement section.

PROBLEM: Vista is shaking. SOLUTION: Check the canopy, chassis, motors and rotor blades for damage.

PROBLEM: The USB charger LED blinks rapidly when attempting to charge the

battery.

SOLUTION: The battery voltage is too low to charge. The battery voltage may

recover on its own with time in order to be safely charged. Wait 1

hour and try charging again. If the charger LED still blinks rapidly

then you may need to replace the battery.

VIDEO PROBLEMSPROBLEM: There are missing or corrupt files on the memory card.

SOLUTION: Refer to RECORDING VIDEO AND PICTURES WITHOUT THE APP for

information regarding camera initialization and closing of files.

SOLUTION: The battery voltage may be getting too low for the camera to operate

properly. When the low voltage LEDs blink, land the Vista and stop

recording as soon as possible.

SOLUTION: Allow 2-3 seconds between taking pictures.

PROBLEM: The video button on the controller does not work or works intermittently.

SOLUTION: The video button must be pressed and quickly released. The controller

will beep when the button works properly.

SOLUTION: The video button on the controller toggles between start/stop video.

If using both the app and the video button to control video recording,

you may need to press the video button a second time in some

instances to get the correct start or stop command.

PROBLEM: The WiFi connection is lost during flight.

SOLUTION: There may be interference in the area. Try flying in a different location.

SOLUTION: You are exceeding the WiFi range of the DroneView camera. Maintain

a closer proximity to your device during flight.

PROBLEM: The app does not re-establish connection after the connection has

been lost.

SOLUTION: Close the DroneView app and remove it from the background tasks.

Restart the DroneView app.

PROBLEM: Exporting files was interrupted and the export function cannot be

restarted.

SOLUTION: Close the DroneView app and remove it from the background tasks.

Restart the DroneView app. Run the export function again.

PROBLEM: You recorded videos/pictures but there are no files on the memory card.

SOLUTION: The memory card was incorrectly inserted into camera. Refer to

RECORDING VIDEO AND PICTURES WITHOUT THE APP for instructions

on the proper installation of the memory card.

PROBLEM: Horizontal scrolling lines appear in video or pictures.

SOLUTION: Avoid aiming the camera directly into the sun or reflected sunlight.

BLADE REPLACEMENT

1. Remove the screw that secures the rotor blade to the gear shaft.

2. Pull the prop off the gear shaft.

3. Install the new rotor blade and secure it with the screw.

NOTE: The rotor blades have arrows that indicate which direction they rotate.

Please refer to this diagram to verify that the correct replacement rotor blade is

installed.

6

PROP SHAFT REPLACEMENT 1. Remove the rotor blade from the

prop shaft.

2. Push the shaft down to remove it

from the gear.

3. Install the new gear shaft and rotor

blade if it is not damaged.

NOTE: While the gear is out, check

it carefully for any cracks or damage

to the teeth.

MOTOR REPLACEMENT

1. Remove the screws securing

the motor cover to the arm and

pull the cover off the motor.

2. Use a small flat blade

screwdriver to separate the

motor plug from the socket.

DO NOT pull the wires.

3. Remove the motor from

the frame and insert the

replacement. Make sure

that the wire colors on the

replacement motor are the

same as the original. The

motors for the clockwise props

have black and white wires.

The counter-clockwise props

use motors with blue and red wires.

FLIGHT CONTROL BOARD REPLACEMENT 1. Remove all four motor covers and the two screws in the section between

the front and back arms.

2. Remove the battery frame screws and battery frame.

3. Carefully lift up each bottom frame separating them from the main frame.

Use your thumbs to push the lens strips from the outside toward the inside

of the bottom frame. It may take a small amount of force to push the lens

covers off the mounting pins. Push straight inward so as not to break the

mounting pins off.

4. Remove the two canopy screws and the canopy. Under the canopy is the

canopy LED strip that must be unplugged from the control board.

5. Remove the 3 screws holding the control board and remove the board.

6. Install the canopy LED strip and the canopy. Be sure that the post is supporting

the back of the LED strip.

7. Install the new control board and route the wires for motors. To prevent

damage to the wires, route them between the guides on the inside of the

arms.

8. Install the bottom frames. Before tightening the screws, make sure the wires

are positioned so they will not be damaged.

9. Replace the motor covers.

10. Calibrate the quadcopter sensors.

7

8

SLT COMPATIBILITYThe Vista has a receiver that is compatible with other SLT transmitters like the

Tactic™ TTX660.

Here is the setup for the Tactic TTX660 transmitter.

Tactic TTX660The model should be set up as a DRONE.

SERVO SET: All channels set to NOR.

DUAL, EXPO: Not used.

CH5 AND CH6 SET:

INPUT: CH5CONTROL: SB ( )OFFSET: +25%TRAVEL: +50% +75%

INPUT: CH6CONTROL: SH ( )OFFSET: +30%TRAVEL: +30% 0%

THROTTLE CURVE: Not used.

THROTTLE CUT: Not used.

AILERON MIXER: Not used.

RUDDER MIXER: Not used.

PROGRAMMABLE MIXER:

MIX 1: CH6>CH6 SF OFFRATE L: –100% R: +100%OFFSET: +50%CTRL: SF OFF

NOTE: The Tactic TTX 660 transmitter is not capable of activating the DroneView camera. You will need to use the DroneView app to start and stop the camera. CH5 is used to control the 3-position dual rate switch which is set at Switch B on your transmitter. Unlike the Vista transmitter, this setup will allow you three different sensitivity rates. Adjust the offset and travel values of CH5 to suit your tastes for rate sensitivity. Switch F will make the Vista fl ip as described in the fl ipping section of this manual. Switch H turns the stabilization on and off. Position 0 and 1 are ON and position 2 is OFF.

90-DAY LIMITED WARRANTY PLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE. Dromida will repair or replace factory defects for 90 days from the date of purchase. This warranty specifi cally does not cover crash damage, misuse or abuse. To make a warranty claim, please contact our product support team atdromida.com/support.

This warranty applies only if the product is operated in compliance with the instructions and warnings provided with each model. Dromida assumes no liability except for the exclusive remedy or repair of parts as specifi ed above. Dromida shall not be liable for consequential or incidental damages. Some states do not allow the exclusion of consequential or incidental damages so the above exclusion may not apply to you. This warranty gives you specifi c legal rights and you may also have other rights which vary from state to state.

9

ISED EXPOSITION AUX RADIATIONS:

Cet équipement est conforme avec ISED les limites d’exposition aux rayonnements défi nies pour un contrôlé environnement.

Cet émetteur ne doit pas être co-localisés ou fonctionner en conjonction avec une autre antenne ou émetteur.

Cet équipement doit être installé et utilisé avec un minimum de 1.8 m de distance entre le radiateur et votre corps

IC: 11104A-MR100B

CE COMPLIANCE INFORMATIONFOR THE EUROPEAN UNION INSTRUCTIONS FOR DISPOSAL OF WASTE EQUIPMENT BY PRIVATE USERS IN THE EUROPEAN UNION:

This symbol on the product or its packaging indicates this product must not be disposed of with other household waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city offi ce, your household waste disposal service or location where you purchased the product.

DECLARATION OF CONFORMITY:

Product: Dromida 2.4GHz 4-Channel Tx Rx

Item number: DIDJ1105 MR100

Equipment class: 1

MR100 transmitter: The objects of the declaration described here are

in conformity with the requirements of the specifi cations listed below,

following the provisions of the European 2014/35/EU Low Voltage Directive:

EN 60950-1:2006

2006+A11:2009+A1:2010+A12:2011+A2:2013

The objects of the declaration described here are in conformity with the

requirements of the specifi cations listed below, following the provisions

of the European RED directive 2014/53/EU:

EN 301 489-1V2.1.1

EN301 489-17 V2.2.1.

EN 300 328 V2.1.1

Hobbico, Inc.2904 Research Road

Champaign, IL USA 61826

FCC REQUIREMENT This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

FCC ID: IYFMR100B

ISED RSS WARNINGThis device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

ISED RADIATION EXPOSURE STATEMENT:

This equipment complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment should be installed and operated with minimum distance 1.8m between the radiator & your body.

10

REPLACEMENT PARTS 1 DIDE1201 Canopy Blue

1 DIDE1202 Canopy Yellow

2 DIDE1204 Prop Set Yellow/Black

2 DIDE1171 Prop Set Blue/Black

3 DIDE1175 Bearing Set

4 DIDE1176 Gear Set

5 DIDE1177 Prop Shaft

6 DIDE1206 Battery Frame/Camera Mount

7 DIDE1208 Main Frame Blue

7 DIDE1209 Main Frame Yellow

8, 19 DIDE1220 Motor Covers

9 DIDE1218 Main Motor CW L/F, R/R

10 DIDE1219 Main Motor CCW R/F, L/R

11 DIDE1307 Bottom Frame Vista FPV V2

12 DIDE1187 LED E-Board Dampers

13 DIDE1188 Screw Set

14 DIDM1217 E-Board Vista FPV V2 Blue

14 DIDM1218 E-Board Vista FPV V2 Yellow

15 ONXP0980 LiPo 850mAh 1S

16 DIDE1189 Canopy LED Light Strip

17 DIDE1216 Camera Power Wire

18 DIDE1215 TX Mobile Phone Holder MR100

20 DIDE1217 ISO Camera Mount Grommet Pins

21 TACZ1001 Tactic DroneView Camera Only

22 DIDE1309 LED Covers Vista FPV V2

DIDP1121 USB Charger 1S LiPo

DIDJ1105 Controller

TACZ1010 4G Memory Card

11

13

9

13

19

19

8

20

20

8

9

5

9

3

22

2

13

2

1

13

2

4

3

7

11

11

3

5

8

13

19

8

18

22

11

22

13

13

3

4

6

17

13

13

13

13

12

21

11

3

3

4

13

3

2

4

3

5

9

13

8

8

22

16

14

13

13

10

5

10

13

8

19

8

15

10

13

dromida.com© 2018 Dromida®, a Hobbico® company. DIDE17BW, DIDE17YW