-
1FEATURES SUPPORTS DEFENSE, AEROSPACE,
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN-
1IN+
VCC+
2IN+
2IN-
2OUT
NC
4OUT
4IN-
4IN+
VCC- /GND
3IN+
3IN-
3OUT
NC
DW PACKAGE
(TOP VIEW)
DESCRIPTION
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
QUAD PRECISION OPERATIONAL AMPLIFIER
AND MEDICAL APPLICATIONS• Single-Supply Operation:• Controlled
BaselineInput Voltage Range Extends to Ground, and
Output Swings to Ground While Sinking • One Assembly/Test
SiteCurrent • One Fabrication Site
• Input Offset Voltage 300 mV Max at 25°C • Available in
Military (–55°C/125°C)Temperature Range (1)• Offset Voltage
Temperature Coefficient
• Extended Product Life Cycle2.5 µV/°C Max• Extended
Product-Change Notification• Input Offset Current 1.5 nA Max at
25°C• Product Traceability• High Gain 1.2 V/µV Min (RL = 2 kΩ),
0.5 V/µV Min (RL = 600 Ω)• Low Supply Current 2.2 mA Max at
25°C• Low Peak-to-Peak Noise Voltage
0.55 µV Typ• Low Current Noise 0.07 pA/√Hz Typ
(1) Additional temperature ranges are available - contact
factory
The LT1014D is a quad precision operational amplifier with
14-pin industry-standard configuration. It features
lowoffset-voltage temperature coefficient, high gain, low supply
current, and low noise.
The LT1014D can be operated with both dual ±15-V and single 5-V
power supplies. The common-mode inputvoltage range includes ground,
and the output voltage can also swing to within a few milivolts of
ground.Crossover distortion is eliminated.
ORDERING INFORMATION (1)
TA PACKAGE (2) ORDERABLE PART NUMBER TOP-SIDE MARKING–55°C to
125°C SIOC-DW Reel of 2000 LT1014DMDWREP LT1014DMEP
(1) For the most current package and ordering information, see
the Package Option Addendum at the end of this document, or see the
TIWeb site at www.ti.com.
(2) Package drawings, standard packing quantities, thermal data,
symbolization, and PCB design guidelines are available
atwww.ti.com/sc/package.
1
Please be aware that an important notice concerning
availability, standard warranty, and use in critical applications
of TexasInstruments semiconductor products and disclaimers thereto
appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2008, Texas Instruments IncorporatedProducts conform to
specifications per the terms of the TexasInstruments standard
warranty. Production processing does notnecessarily include testing
of all parameters.
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.ti.comhttp://www.ti.com/sc/package
-
VC
C+
IN−
IN+
V CC
−
Ωk9
Ωk9
Ωk1.
6Ωk
1.6
Ωk1.
6Ω
100
Ωk1
Ω80
0
Q5
Q6
Q13
Q16
Q14
Q15
Q32
Q30
Q25
Q35
Q36
Q41
Q39
Ω60
0
Q3
Q4
Q37
J1
Q33
Q26
Ωk3.
9
Q27
Q38
Q28
Q2
Q22
Q1
Q21
Ω40
0
Ω40
0
Q12
Q11
Q9
75 p
F
Q7Q
29
Q10
Q18
Q19
Q17
21 p
F2.
5 pF
Ωk2.
4
Ω18
Ωk14 OU
T
Q40
Q8
Ωk5
Ωk5
10 p
F
Ωk2
Ωk1.
3
Q20
4 pF
Q31
Q34
Q23
Q24
Ωk2 1
0 pF
Ωk2
Ω30
Ωk42
Com
pone
nt v
alue
s ar
e no
min
al.
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
SCHEMATIC (EACH AMPLIFIER)
2 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
ABSOLUTE MAXIMUM RATINGS
DISSIPATION RATINGS
ELECTRICAL CHARACTERISTICS
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
over operating free-air temperature range (unless otherwise
noted) (1)
MIN MAX UNITVCC supply voltage (2) –22 22 V
Differential input voltage (3) –30 30 VVI Input voltage range
(any input) (2) VCC- – 5 VCC+ V
Duration of short-circuit current (4) TA ≤ 25°C
UnlimitedContinuous total power dissipation See Dissipation Ratings
Table
TA Operating temperature range –55 125 °CTstg Storage
temperature range –65 150 °C
Lead temperature 1,6 mm, at distance 1/16 inch from case for 10s
260 °C
(1) Stresses beyond those listed under "absolute maximum
ratings" may cause permanent damage to the device. These are stress
ratingsonly, and functional operation of the device at these or any
other conditions beyond those indicated under "recommended
operatingconditions" is not implied. Exposure to
absolute-maximum-rated conditions for extended periods may affect
device reliability.
(2) All voltage values, except differential voltages, are with
respect to the midpoint between VCC+ and VCC-.(3) Differential
voltages are at the noninverting input with respect to the
inverting input.(4) The output may be shorted to either supply.
DERATINGTA ≤ 25°c TA = 70°C TA = 105°C TA = 125°CPACKAGE
FACTORPOWER RATING POWER RATING POWER RATING POWER RATINGABOVE TA =
25°CDW 1025 mV 8.2 mW/°C 656 mW 369 mW 205 mW
over operating free-air temperature range, VCC+ = 5 V, VCC- = 0,
VO = 1.4 V, VIC = 0 (unless otherwise noted)
PARAMETER TEST CONDITIONS TA(1) MIN TYP MAX UNIT25°C 90 450
RS = 50 ΩVIO Input offset voltage Full range 400 1500 µVRS = 50
Ω, VIC = 0.1 V 125°C 200 750
25°C 0.2 2IIO Input offset current nAFull range 10
25°C -15 -50IIB Input bias current nAFull range -120
25°C 0 to 3.5 -0.3 to 3.8Common-mode input voltageVICR Vrange
Full range 0.1 to 3Output low, no load 25°C 15 25
25°C 5 10Ouput low, RL = 600 Ω to GND mVFull range 18
Maximum peak outputVOM Output low, ISINK = 1 mA 25°C 220
350voltage swingOutput high, no load 25°C 4 4.4Output high 25°C 3.4
4 VRL = 600 Ω to GND Full range 3.1
Large-signal differentialAVD VO = 5 mV to 4 V, RL = 500 Ω 25°C 1
V/µVvoltage amplification25°C 0.3 0.5
ICC Supply current per amplifier mAFull range 0.65
(1) Full range is -55°C to 125°C.
Copyright © 2008, Texas Instruments Incorporated Submit
Documentation Feedback 3
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
OPERATING CHARACTERISTICS
TYPICAL CHARACTERISTICS
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
over operating free-air temperature range, VCC± = 15 V, VIC = 0,
TA = 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNITSR Slew rate 0.2 0.4
V/µs
f = 10 Hz 24Vn Equivalent input noise voltage nV/√Hzf = 1kHz
22VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to
10 Hz 0.55 µVIn Equivalent input noise current f = 10 Hz 0.07
pA/√Hz
Table of GraphsFIGURE
VIO Input offset voltage vs balanced source resistance Figure
2VIO Input offset voltage vs free-air temperature Figure 3ΔVIO
Warm-up change in input offset voltage vs elapsed time Figure 4IIO
Input offset current vs Input offset current vs free-air
temperature Figure 5IIB Input bias current vs free-air temperature
Figure 6VIC Common-mode input voltage vs input bias current Figure
7
vs load resistance Figure 8 Figure 9AVD Differential voltage
amplification vs frequency Figure 10 Figure 11
Channel separation vs frequency Figure 12Output saturation
voltage vs free-air temperature Figure 13
CMRR Common-mode rejection ratio vs frequency Figure 14kSVR
Supply-voltage rejection ratio vs frequency Figure 15ICC Supply
current vs free-air temperature Figure 16IOS Short-circuit output
current vs elapsed time Figure 17Vn Equivalent input noise voltage
vs frequency Figure 18In Equivalent input noise current vs
frequency Figure 18
VN(PP) Peak-to-peak input noise voltage vs time Figure 19Pulse
response (small signal) vs time Figure 20 Figure 22Pulse response
(large signal) vs time Figure 21 Figure 23 Figure 24Phase shift vs
frequency Figure 10
4 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
Rs - Sour ce Resistance - Ω
INPUT OFFSET VOLTAGE
vs
BALANCED SOURCE RESISTANCE
- In
pu
t O
ffset
Vo
ltag
e -
mV
1 k
0.01
0.1
1
10
-
+
TA = 25°C
VCC± = 5 V
VCC- = 0
VIO
VCC± = ±15 V
RS
RS
3 k 10 k 30 k 100 k 300 k 1 M 3 M 10 M
TA - Free-Air Temperature - °C
INPUT OFFSET VOLTAGE
OF REPRESENTATIVE UNITS
vs
FREE-AIR TEMPERATURE
VCC± = ±15 V
- In
put O
ffset
Volta
ge -
mV
VIO
250
200
150
100
50
0
-50
-100
-150
-200
-250
-50 -25 0 25 50 75 100 125
3
2
1
00 1 2 3
- C
hang
e in Input O
ffset
Votla
ge -
Vm
4
t - Time After P ower-On - min
WARM-UP CHANGE IN INPUT OFFSET VOLTAGE
vs
ELAPSED TIME
5
4 5
N Package
VCC± = ±15 V
TA = 25°C
∆V
IO J Package0.2
0
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
1
0.4
0.6
0.8
VIC = 0
VCC± = ±2.5 V
TA - Free-Air Temperature - °C
VCC+ = 5 V, VCC- = 0
-50 -25 0 25 50 75 100 125
- In
pu
t O
ffset
Cu
rren
t -
nA
I IO
VCC± = ±15 V
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
Figure 2. Figure 3.
Figure 4. Figure 5.
Copyright © 2008, Texas Instruments Incorporated Submit
Documentation Feedback 5
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
IIB - Input Bias Current - nA
COMMON-MODE INPUT VOLTAGE
vs
INPUT BIAS CURRENT
TA = 25°C
VCC± = ±15 V
(Left Scale) VCC+ = 5 V
VCC- = 0
(Right Scale)
- C
om
mo
n-M
od
e In
pu
tVo
ltag
e -
VV
IC
15
10
5
0
-5
-10
-150 -5 -10 -15 -20 -25 -30
5
3
4
2
1
0
-1
- C
om
mo
n-M
od
e In
pu
tVo
ltag
e -
VV
IC
TA - Free-Air Temperature - °C
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
VIC = 0
VCC = 5 V, VCC- = 0
VCC± = ±2.5 V
VCC± = ±15 V
- In
pu
t B
ias C
urr
en
t -
nA
I IB
-30
-25
-20
-15
-10
-5
0-50 -25 0 25 50 75 100 125
RL - Load Resistance - Ω
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
VCC± = ±15 V
VO = ±10 V
TA = -55 °C
TA = 25°C
TA = 125°C
- D
iff
ere
nti
alV
olt
ag
eA
mp
livic
ati
on
-V
/V
mA
VD
100 400 1 k 4 k 10 k
10
4
1
0.4
0.1
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
VCC+ = 5 V, VCC- = 0
VO = 20 mV to 3.5 V
TA = -55 °C
TA = 25°C
TA = 125°C
- D
iff
ere
nti
alV
olt
ag
eA
mp
livic
ati
on
-V
/V
mA
VD
RL - Load Resistance - Ω
100 400 1 k 4 k 10 k
10
4
1
0.4
0.1
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
Figure 6. Figure 7.
Figure 8. Figure 9.
6 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
VCC + = 5 V
VCC - = 0VCC± = ±15 V
CL = 100 pF
TA = 25°C
- D
iff
ere
nti
alV
olt
ag
eA
mp
livic
ati
on
- d
BA
VD
f - Frequenc y - Hz
0.01 0.1 1 k 100 k 10 M1 10 100 10 k 1 M
0
-20
20
40
60
80
100
120
140
f - Frequenc y - MHz
DIFFERENTIAL VOLTAGE AMPLIFICATION
AND PHASE SHIFT
vs
FREQUENCY
AVD
VCC+ = 5 V
VCC- = 0
VCC± = ±15 V
VIC = 0
CL = 100 pF
TA = 25°C
VCC+ = 5 V
VCC- = 0
φ
VCC± = ±15 V
- D
iff
ere
nti
alV
olt
ag
eA
mp
liv
ica
tio
n -
dB
AV
D
- P
ha
se
Sh
ift
20
10
0
-10
0.01 0.3 1 3 10
80°
100°100°
120°
140°
160°
180°
200°
220°
240°
120
100
80
6010 100 1 k 10 k
Ch
an
nel S
ep
ara
tio
n -
dB
140
f - Frequenc y - Hz
CHANNEL SEPARATION
vs
FREQUENCY160
100 k 1 M
Limited by
Thermal
InteractionRL = 100 Ω
RL = 1 kΩ
Limited by
Pin-to-Pin
Capacitance
VCC± = ±15 V
VI(PP) = 20 V to 5 kHz
RL = 2 kΩ
TA = 25°C
Ou
tpu
t S
atu
rati
on
Vo
ltag
e -
V
OUTPUT SATURATION VOLTAGE
vs
FREE-AIR TEMPERATURE
TA - Free-Air Temperature - °C
VCC+ = 5 V to 30 V
VCC- = 0
Isink = 10 mA
Isink = 1 mA
Isink = 100 µA
Isink = 10 µA
Isink = 0
Isink = 5 mA
10
1
0.1
0.01-50 -25 0 25 50 75 100 125
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
Figure 10. Figure 11.
Figure 12. Figure 13.
Copyright © 2008, Texas Instruments Incorporated Submit
Documentation Feedback 7
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
60
40
20
010 100 1 k 10 k
CM
RR
- C
om
mo
n-M
od
e R
eje
cti
on
Rati
o -
dB
80
100
f - Frequenc y - Hz
COMMON-MODE REJECTION RATIO
vs
FREQUENCY120
100 k 1 M
VCC+ = 5 V
VCC- = 0
VCC± = ±15 V
TA = 25°C
0.1 1 10 100 1 k
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
10 k 100 k 1 M0
20
40
60
80
100
120
140
f - Frequenc y - Hz
Negative
Supply
Positive
Supply
VCC± = ± 15 V
TA = 25°C
- S
up
ply-V
olt
ag
e R
eje
cti
on
Rati
o -
dB
KS
VR
0 1
0
10
t - Time - min
SHORT-CIRCUIT OUTPUT CURRENT
vs
ELAPSED TIME
20
2 3
30
40
TA = 25°C
TA = 125°C
TA = 25°C
TA = -55 °C
TA = 125°C
VCC± = ±15 VTA = -55 °C
-10
-20
-30
-40
- S
ho
rt-
Cir
cu
it O
utp
ut
Cu
rren
t -
mA
IO
S
- S
up
ply C
urr
en
t P
erA
mp
lifi
er
-V
m
TA - Free-Air Temperature - °C
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
0 25 50 75 100 125260
300
340
380
420
460
VCC+ = 5 V
VCC- = 0
VCC± = ±15 V
-25-50
I CC
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
Figure 14. Figure 15.
Figure 16. Figure 17.
8 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
100
1000
300
1 10
f - Frequenc y - Hz
EQUIVALENT INPUT NOISE VOLTAGE
AND EQUIVALENT INPUT NOISE CURRENT
vs
FREQUENCY
30
10100
VCC± = ±2 V to ±18 V
TA = 25°C
In
Vn
100
1000
300
30
101 k
1/f Corner = 2 Hz-
Eq
uiv
ale
nt
Inp
ut
No
ise C
urr
en
t -
I nfA
/H
z
- E
qu
ivale
nt
Inp
ut
No
ise
Volt
ag
e -
Vn
fA/
Hz
1200
800
400
00 2 4 6
1600
t - Time - s
PEAK-TO-PEAK INPUT NOISE VOLTAGE
OVER A 10-SECOND PERIOD
vs
TIME2000
8 10
VCC± = ±2 V to ±18 V
f = 0.1 Hz to 10 Hz
TA = 25°C
- N
ois
eV
olt
ag
e -
nV
VN
(PP
)
t - Time - sm
0
4 6 8 10
60
80
12 14
40
20
20
VCC± = ±15 V
AV = 1
TA = 25°C
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
vs
TIME
-20
-40
-60
-80
- O
utp
ut
Vo
ltag
e -
mV
VO
2
0 10 20 30
3
5
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME6
40 50 60 70
4
t - Time - sm
VCC+ = 5 V
VCC- = 0
VI = 0 to 4 V
RL = 0
AV = 1
TA = 25°C
1
0
-1
-2
- O
utp
ut
Vo
ltag
e -
VV
O
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
Figure 18. Figure 19.
Figure 20. Figure 21.
Copyright © 2008, Texas Instruments Incorporated Submit
Documentation Feedback 9
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
t - Time - sm
2
1
0 10 20 30
3
5
6
40 50 60 70
0
4
VCC+ = 5 V
VCC- = 0
VI = 0 to 4 V
RL = 4.7 kΩ to 5 V
AV = 1
TA = 25°C
-1
-2-
Ou
tpu
tV
olt
ag
e -
mV
VO
t - TIme - sm
60
40
0
0 20 40 60
80
120
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
vs
TIME
140
80 100 120 140
20
100
160VCC+ = 5 V
VCC- = 0
VI = 0 to 100 mV
RL = 600 Ω to GND
AV = 1
TA = 25°C
-20
- O
utp
ut
Vo
ltag
e -
mV
VO
t - Time - sm
2
1
0 10 20 30
3
5
6
40 50 60 70
0
4
VCC+ = 5 V
VCC- = 0
VI = 0 to 4 V
RL = 0
AV = 1
TA = 25°C
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
-1
-2
- O
utp
ut
Vo
ltag
e -
VV
O
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
Figure 22. Figure 23.
Figure 24.
10 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
APPLICATION INFORMATION
SINGLE-SUPPLY OPERATION
(a) VI(PP) = −1.5 V to 4.5 V (b) Output Phase ReversalExhibited
by LM358
(c) No Phase ReversalExhibited by L T1014
− In
put V
olta
ge −
VV
I(P
P)
− O
utpu
t Vol
tage
− V
VO
− O
utpu
t Vol
tage
− V
VO
5
4
3
2
1
0
−1
−2
5
4
3
2
1
0
−1
5
4
3
2
1
0
−1
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
The LT1014D is fully specified for single-supply operation (VCC-
= 0). The common-mode input voltage rangeincludes ground, and the
output swings within a few millivolts of ground.
Furthermore, the LT1014D has specific circuitry that addresses
the difficulties of single-supply operation, both atthe input and
at the output. At the input, the driving signal can fall below 0 V,
either inadvertently or on atransient basis. If the input is more
than a few hundred millivolts below ground, the LT1014D is designed
to dealwith the following two problems that can occur:1. On many
other operational amplifiers, when the input is more than a diode
drop below ground, unlimited
current flows from the substrate (VCC- terminal) to the input,
which can destroy the unit. On the LT1014D, the400-Ω resistors in
series with the input (see schematic) protect the device even when
the input is 5 V belowground.
2. When the input is more than 400 mV below ground (at TA =
25°C), the input stage of similar type operationalamplifiers
saturates, and phase reversal occurs at the output. This can cause
lockup in servo systems.Because of unique phase-reversal protection
circuitry (Q21, Q22, Q27, and Q28), the LT1014D outputs donot
reverse, even when the inputs are at -1.5 V (see Figure 25).
However, this phase-reversal protection circuitry does not
function when the other operational amplifier on theLT1014D is
driven hard into negative saturation at the output. Phase-reversal
protection does not work on anamplifier:• When 4's output is in
negative saturation (the outputs of 2 and 3 have no effect)• When
3's output is in negative saturation (the outputs of 1 and 4 have
no effect)• When 2's output is in negative saturation (the outputs
of 1 and 4 have no effect)• When 1's output is in negative
saturation (the outputs of 2 and 3 have no effect)
At the output, other single-supply designs either cannot swing
to within 600 mV of ground or cannot sink morethan a few
microproamperes while swinging to ground. The all-npn output stage
of the LT1014D maintains its lowoutput resistance and high gain
characteristics until the output is saturated. In dual-supply
operations, the outputstage is free of crossover distortion.
Figure 25. Voltage-Follower ResponseWith Input Exceeding the
Negative Common-Mode Input Voltage Range
Copyright © 2008, Texas Instruments Incorporated Submit
Documentation Feedback 11
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
COMPARATOR APPLICATIONS
100 mV
10 mV 5 mV 2 mV
Diffe
ren
tia
lIn
pu
tV
olta
ge
t - Time - sm
Overdrive
VCC+ = 5 V
VCC- = 0
TA = 25°C
- O
utp
ut
Vo
lta
ge
-V
VO
5
4
3
2
1
0
0 50 100 150 200 250 300 350 400 450
2 mV5 mV
100 mV
Overdrive
10 mV
Dif
fere
nti
al
Inp
utV
olt
ag
et - Time - sm
VCC+ = 5 V
VCC- = 0
TA = 25°C
- O
utp
ut
Vo
ltag
e -
VV
O
5
4
3
2
1
0
0 50 100 150 200 250 300 350 400 450
LOW-SUPPLY OPERATION
OFFSET VOLTAGE AND NOISE TESTING
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
The single-supply operation of the LT1014D can be used as a
precision comparator with TTL-compatible output.In systems using
both operational amplifiers and comparators, the LT1014D can
perform multiple duties (seeFigure 26 and Figure 27).
Figure 26. Low-to-High-Level Output ResponseFigure 27.
High-to-Low-Level Output Responsefor Various Input Overdrives
for Various Input Overdrives
The minimum supply voltage for proper operation of the LT1014D
is 3.4 V (three Ni-Cad batteries). Typicalsupply current at this
voltage is 290 µA; therefore, power dissipation is only 1 mW per
amplifier.
Figure 31shows the test circuit for measuring input offset
voltage and its temperature coefficient. This circuit withsupply
voltages increased to ±20 V is also used as the burn-in
configuration.
The peak-to-peak equivalent input noise voltage of the LT1014D
is measured using the test circuit shown inFigure 28. The frequency
response of the noise tester indicates that the 0.1-Hz corner is
defined by only onezero. The test time to measure 0.1-Hz to 10-Hz
noise should not exceed 10 seconds, as this time limit acts as
anadditional zero to eliminate noise contribution from the
frequency band below 0.1 Hz.
An input noise-voltage test is recommended when measuring the
noise of a large number of units. A 10-Hz inputnoise-voltage
measurement correlates well with a 0.1-Hz peak-to-peak noise
reading because both results aredetermined by the white noise and
the location of the 1/f corner frequency.
Noise current is measured by the circuit and formula shown in
Figure 29. The noise of the source resistors issubtracted.
12 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
10 Ω
100 kΩ
0.1 µF
2 kΩ
4.7 µF
AVD = 50,000
24.3 kΩ
100 kΩ
0.1 µF
4.3 kΩ
2.2 µF
110 kΩ
22 µFOscilloscopeRin = 1 MΩ
NOTE A: All capacitor values are for nonpolarized capacitors
only.
LT1014
+
− LT1001
+
−
10 kΩ
10 Mن
100 ٠Vn In ��V
no2� (820 nV)2�
1�2
40 M�� 100
† Metal-film resistor
10 Mن
10 Mن 10 MنLT1014
+
−
15 V
−15 V
VO = 1000 VIO100 Ω
(see Note A)
50 Ω(see Note A)
LT1014
+
−
50 Ω(see Note A)
NOTE A: Resistors must have low thermoelectric potential.
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
Figure 28. 0.1-Hz to 10-Hz Peak-to-Peak Noise Test Circuit
Figure 29. Noise-Current Test Circuit and Formula
Figure 30. Test Circuit for VIO and αVIO
Copyright © 2008, Texas Instruments Incorporated Submit
Documentation Feedback 13
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
5 V
100 pF
2 kΩ
Q42N2222
Q32N2905
5 V
68 Ω
4.3 kΩ
LT10041.2 V
4 kن
10 kΩ†1 kΩ4-mATrim
IN0 to 4 V
4-mA to 20-mA OUTTo Load2.2 kΩ Max
100 Ω†
10 Ω†
10 kن20-mATrim
80 Ω†
100 kΩ
5 V
0.33 µF
10 kΩ 820 Ω Q22N2905
SN74HC04 (6)
820 ΩQ12N2905
1N4002 (4)
10 µF10 µF
T1‡
0.002 µF
1/4LT1014
1/4LT1014
† 1% film resistor. Match 10-kΩ resistors 0.05%.‡ T1 =
PICO-31080
+
±
+
±
++
10 kΩ 10 kΩ
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
Figure 31. 5-V Powered, 4-mA to 20-mA Current-Loop Transmitter
With 12-Bit Accuracy
14 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
ToInverter
Driver
5 V100 kΩ
10 kن
68 kن
4.3 kΩ5 V
LT10041.2 V
4 kن
2 kΩ4-mATrim
IN0 to 4 V
1 kΩ20-mATrim
301 Ω†
0.1 Ω T1
10 µF
4-mA to 20-mA OUTFully Floating
1N4002 (4)
† 1% film resistor
+
−1/4
LT1014
1/4LT1014
+
−
+
IN+
IN−
5 V
OUT A
R2
R1
1 µF1 µF
1/2 LTC1043
NOTE A: VIO = 150 µV, AVD = (R1/R2) + 1, CMRR = 120 dB, VICR = 0
to 5 V
1/4LT1014
+
−
6
18 15
5
6
8
4
72
3
IN+
IN−
OUT B
R2
R1
1 µF1 µF
1/2 LTC1043
1/4LT1014
+
−
7
13 14
3
2
111
12
5
8
0.01 µF
LT1014D-EP
www.ti.com
...........................................................................................................................................................................................
SLOS609–DECEMBER 2008
Figure 32. Fully Floating Modification to 4-mA to 20-mA
Current-Loop Transmitter With 8-Bit Accuracy
Figure 33. 5-V Single-Supply Dual Instrumentation Amplifier
Copyright © 2008, Texas Instruments Incorporated Submit
Documentation Feedback 15
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
To Input
Cable Shields
RG (2 kΩ Typ)
200 kΩ
10 kΩ
10 kΩ †
10 kΩ †
OUT
20 kΩ
20 kΩ
200 kΩ †
5 V
IN-
IN+
1 µF
‡
† 1% film resistor. Match 10-kΩ resistors 0.05%.‡ For high
source impedances, use 2N2222 as diodes (with collector connected
to base).
NOTE A: AVD = (400,000/RG) + 1
LT1014
+
-
LT1014
-
+
LT1014
-
+
LT1014
-
+
5 V
‡
10 kΩ
10 kΩ †
5 V
10 kΩ †
2
3
6
5
‡
‡
1
7
10
9
13
12
14
8
4
11
LT1014D-EP
SLOS609–DECEMBER 2008
...........................................................................................................................................................................................
www.ti.com
Figure 34. 5-V Powered Precision Instrumentation Amplifier
16 Submit Documentation Feedback Copyright © 2008, Texas
Instruments Incorporated
Product Folder Link(s): LT1014D-EP
http://focus.ti.com/docs/prod/folders/print/lt1014d-ep.htmlhttp://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SLOS609&partnum=LT1014D-EPhttp://focus.ti.com/docs/prod/folders/print/lt1014d-ep.html
-
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead finish/Ball material
(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
LT1014DMDWREP ACTIVE SOIC DW 16 2000 RoHS & Green NIPDAU
Level-1-260C-UNLIM -55 to 125 LT1014DMEP
V62/09614-01XE ACTIVE SOIC DW 16 2000 RoHS & Green NIPDAU
Level-1-260C-UNLIM -55 to 125 LT1014DMEP
(1) The marketing status values are defined as follows:ACTIVE:
Product device recommended for new designs.LIFEBUY: TI has
announced that the device will be discontinued, and a lifetime-buy
period is in effect.NRND: Not recommended for new designs. Device
is in production to support existing customers, but TI does not
recommend using this part in a new design.PREVIEW: Device has been
announced but is not in production. Samples may or may not be
available.OBSOLETE: TI has discontinued the production of the
device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that
are compliant with the current EU RoHS requirements for all 10 RoHS
substances, including the requirement that RoHS substancedo not
exceed 0.1% by weight in homogeneous materials. Where designed to
be soldered at high temperatures, "RoHS" products are suitable for
use in specified lead-free processes. TI mayreference these types
of products as "Pb-Free".RoHS Exempt: TI defines "RoHS Exempt" to
mean products that contain lead but are compliant with EU RoHS
pursuant to a specific EU RoHS exemption.Green: TI defines "Green"
to mean the content of Chlorine (Cl) and Bromine (Br) based flame
retardants meet JS709B low halogen requirements of
-
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 2
OTHER QUALIFIED VERSIONS OF LT1014D-EP :
• Catalog: LT1014D
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
http://focus.ti.com/docs/prod/folders/print/lt1014d.html
-
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
LT1014DMDWREP SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0
16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 12-Feb-2019
Pack Materials-Page 1
-
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width
(mm) Height (mm)
LT1014DMDWREP SOIC DW 16 2000 350.0 350.0 43.0
PACKAGE MATERIALS INFORMATION
www.ti.com 12-Feb-2019
Pack Materials-Page 2
-
www.ti.com
GENERIC PACKAGE VIEW
This image is a representation of the package family, actual
package may vary.Refer to the product data sheet for package
details.
SOIC - 2.65 mm max heightDW 16SMALL OUTLINE INTEGRATED
CIRCUIT7.5 x 10.3, 1.27 mm pitch
4224780/A
-
www.ti.com
PACKAGE OUTLINE
C
TYP10.639.97
2.65 MAX
14X 1.27
16X 0.510.31
2X8.89
TYP0.330.10
0 - 80.30.1
(1.4)
0.25GAGE PLANE
1.270.40
A
NOTE 3
10.510.1
BNOTE 4
7.67.4
4220721/A 07/2016
SOIC - 2.65 mm max heightDW0016ASOIC
NOTES: 1. All linear dimensions are in millimeters. Dimensions
in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M. 2. This drawing is subject to change without
notice. 3. This dimension does not include mold flash, protrusions,
or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm, per side. 4. This dimension does not include
interlead flash. Interlead flash shall not exceed 0.25 mm, per
side.5. Reference JEDEC registration MS-013.
1 16
0.25 C A B
98
PIN 1 IDAREA
SEATING PLANE
0.1 C
SEE DETAIL A
DETAIL ATYPICAL
SCALE 1.500
-
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAXALL AROUND
0.07 MINALL AROUND
(9.3)
14X (1.27)
R0.05 TYP
16X (2)
16X (0.6)
4220721/A 07/2016
SOIC - 2.65 mm max heightDW0016ASOIC
NOTES: (continued) 6. Publication IPC-7351 may have alternate
designs. 7. Solder mask tolerances between and around signal pads
can vary based on board fabrication site.
METAL SOLDER MASKOPENING
NON SOLDER MASKDEFINED
SOLDER MASK DETAILS
OPENINGSOLDER MASK METAL
SOLDER MASKDEFINED
LAND PATTERN EXAMPLESCALE:7X
SYMM
1
8 9
16
SEEDETAILS
SYMM
-
www.ti.com
EXAMPLE STENCIL DESIGN
R0.05 TYP
16X (2)
16X (0.6)
14X (1.27)
(9.3)
4220721/A 07/2016
SOIC - 2.65 mm max heightDW0016ASOIC
NOTES: (continued) 8. Laser cutting apertures with trapezoidal
walls and rounded corners may offer better paste release. IPC-7525
may have alternate design recommendations. 9. Board assembly site
may have different recommendations for stencil design.
SOLDER PASTE EXAMPLEBASED ON 0.125 mm THICK STENCIL
SCALE:7X
SYMM
SYMM
1
8 9
16
-
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING
DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS),
APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION,
AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL
WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY
RIGHTS.These resources are intended for skilled developers
designing with TI products. You are solely responsible for (1)
selecting the appropriate TI products for your application, (2)
designing, validating and testing your application, and (3)
ensuring your application meets applicable standards, and any other
safety, security, or other requirements. These resources are
subject to change without notice. TI grants you permission to use
these resources only for development of an application that uses
the TI products described in the resource. Other reproduction and
display of these resources is prohibited. No license is granted to
any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and
you will fully indemnify TI and its representatives against, any
claims, damages, costs, losses, and liabilities arising out of your
use of these resources.TI’s products are provided subject to TI’s
Terms of Sale (www.ti.com/legal/termsofsale.html) or other
applicable terms available either on ti.com or provided in
conjunction with such TI products. TI’s provision of these
resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303,
Dallas, Texas 75265Copyright © 2020, Texas Instruments
Incorporated
http://www.ti.com/legal/termsofsale.htmlhttp://www.ti.com
FEATURESSUPPORTS DEFENSE, AEROSPACE, AND MEDICAL
APPLICATIONSDESCRIPTIONABSOLUTE MAXIMUM RATINGSDISSIPATION
RATINGSELECTRICAL CHARACTERISTICSOPERATING CHARACTERISTICSTYPICAL
CHARACTERISTICS
APPLICATION INFORMATIONSINGLE-SUPPLY OPERATIONCOMPARATOR
APPLICATIONSLOW-SUPPLY OPERATIONOFFSET VOLTAGE AND NOISE
TESTING