Q&A Consistency Meeting Agenda for Plumbing, September … · Q&A Consistency Meeting Agenda for Plumbing, September 2016 1. Question: Can condensate drainage piping from HVAC equipment

Q&A Consistency Meeting Agenda for Plumbing, September 2016

1. Question: Can condensate drainage piping from HVAC equipment connect to storm drain conductor

piping? (TR)

Answer: No, Section 1104.1 prohibits using Conductors as Waste Stacks. The connection of drains to the

Storm Conductor would create a Waste Stack. Additionally, under full flow conditions, the pipe may not

have the capacity to drain the rain water. The water would look for a relief under these conditions.

1104.1 Prohibited use. Conductor pipes shall not be used as soil, waste or vent pipes, and soil, waste or

vent pipes shall not be used as conductors.

2. Question: Can push fittings such as SharkBite and Gator Bite be used underground? (TR)

Answer: The evaluation by IAPMO for SharkBite fittings do state underground use. GatorBite has an ICC

evaluation and it only allows inside the building, above ground.

See Attachments

3. Question: Are shower valves required to be directly fastened to a wood cross member? (TR)

Answer: Nothing has been found in the code or the standards to require a shower valve to be directly

fastened to a support. It is acceptable for the hot and cold risers to be attached to the framing on either

side of the valve. This does allow the valve to move slightly. When the trim is installed, this will allow

the valve to pull tight to the trim.

4. Question: Is it acceptable to run the plumbing vent through a wall instead of the roof? (TR)

Answer: Yes, This is sometimes necessary. It would be a better installation on a metal building to run

the plumbing vent through a gable wall instead of penetrating the metal roof.

904.6 Extension through the wall. Vent terminals extending through the wall shall terminate a minimum

of 10 feet (3048 mm) from the lot line and 10 feet (3048 mm) above average ground level. Vent

terminals shall not terminate under the overhang of a structure with soffit vents. Side wall vent

terminals shall not terminate horizontally to prevent birds or rodents from entering or blocking the vent

opening.

IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or acombination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of thesupplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth inthe characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the productacceptance by Authorities Having Jurisdiction.

This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material,manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence ofnon-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing.Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc.Any alteration of this certificate could be grounds for revocation of the listing.

The most updated information on this Certificate of Listing is available online at pld.iapmo.org

Effective Date: July 2016 Void After: July 2017

Product: Push Fit Fittings File No. 4630

Issued To: Cash Acme/Reliance Worldwide2400 7th Ave. SwCullman, AL 35055

Identification: Each fitting shall have the following information marked on it where it will

be visible after it has been installed:

Name of manufacturer or trademark.

When a fitting is not suitable for all four (4) materials, it shall be marked

as follows for the materials for which they are suitable:

- Copper or Cu

- CPVC

- PEX

- PE-RT

When push-fit connectors are used on plumbing devices, the markings are

permitted to be on the plumbing device.

Fittings 1/2" CTS or smaller are permitted to use a permanent label complying

with the requirements of UL 969 or CSA C22.2 N. 0.15 to display the required

markings. The markings shall be permanent. The product shall also bear the

cUPC mark.

Characteristics: Push fit fittings that have a quick assembly push fit mechanism that

Page 2

Void After: July 2017


Issued To: Cash Acme/Reliance Worldwide

can be used with Copper, PEX and CPVC tubing and pipes. Fittings for

use in domestic and commercial application for both potable water distribution

systems and hydronic heating systems. Push fit fittings can be utilized in

underground applications and as manufactured joints without access panels. To

be installed in accordance with the manufacturer's instructions and the latest

edition of the Uniform Plumbing Code and the National Plumbing Code of Canada.

Products listed on this certificate have been tested by an IAPMO R&T

recognized laboratory. This recognition has been granted based upon the

laboratory's compliance to the applicable requirements of ISO/IEC

17025.

Products are in compliance with the following code(s):

Uniform Plumbing Code (UPC®)

National Plumbing Code of Canada

International Plumbing Code (IPC®)

Products are in compliance with the following standard(s):

ASSE 1061-2011

rowlatd

Highlight

rowlatd

Highlight

MODELS:

Note: The requirements of Section 609.3.2 in the Uniform Plumbing Code are satisfied for push fit fittings by section 301.4.1 of the same Uniform Plumbing Code when installed in accordance with the manufacturer's installation guides.Note: All 1/2" through 1" models comply with ANSI/NSF 14.Yorkflex™ & Sharkbite™Model No. Description22995 3/4" Tube x 3/4" Tube 1/2" Sharkbite (3 Branches)22996 3/4" Tube x Closed- 1/2" Sharkbite (3 Branches)22997 3/4" Tube x 3/4" Tube 1/2" Sharkbite (4 Branches)22998 3/4" Tube x Closed- 1/2" Sharkbite (4 Branches)K008 COUPLING 1/2" X 1/2"K016 COUPLING 3/4" X 3/4"K020 COUPLING 1" X 1"K058 REDUCING COUPLING 3/4" X 1/2"K060 REDUCING COUPLING 1" X 3/4"K072 FEMALE CONNECTOR 1/2" X 1/2" FNPT StraightK088 FEMALE CONNECTOR 3/4" X 3/4" FNPT StraightK094 FEMALE CONNECTOR 1" X 1" FNPT StraightK120 MALE CONNECTOR 1/2" X 1/2" MNPT StraightK134 MALE CONNECTOR 3/4" X 3/4" MNPT StraightK140 MALE CONNECTOR 1" X 1" MNPT StraightK248 ELBOW 1/2" X 1/2"K256 ELBOW 3/4" X 3/4"K260 ELBOW 1" X 1"K280 MALE ELBOW 1/2" X 1/2" MNPTK334 DROP-EAR ELBOW 1/2" X 1/2" FNPTK362 TEE 1/2" X 1/2" X 1/2"K370 TEE 3/4" X 3/4" X 3/4"K374 TEE 1" X 1" X 1"K408 REDUCING TEE 1/2" x 1/2" x 3/4" ReducingK412 REDUCING TEE 3/4" X 3/4" X 1/2" ReducingK413 REDUCING TEE 3/4" x 3/4" x 1" ReducingK414 REDUCING TEE 1" X 3/4" X 3/4" ReducingK415 REDUCING TEE 1" X 1" X 1/2" ReducingK416 REDUCING TEE 1" X 1" X 3/4" ReducingK418 REDUCING TEE 1" x 3/4" x 1" ReducingK419 SBPP Reducing TEE 1” x 3/4” x 1/2”K444 REDUCING TEE 3/4" X 1/2" X 3/4" ReducingK454 REDUCING TEE 3/4" X 1/2" X 1/2" ReducingK514 END CAP 1/2"K518 END CAP 3/4"K520 END CAP 1"SB0135 SharkBite 1-1/4" Coupling

Page 3



Issued To: Cash Acme/reliance Worldwide

SB013528 SharkBite 1-1/4" x 1" Reducing CouplingSB0141 SharkBite 1-1/2" CouplingSB014128 SharkBite 2XL 1-1/2" x 1" Reducing CouplingSB014135 SharkBite 1-1/2" x 1-1/4"" Reducing CouplingSB0154 SharkBite 2" CouplingSB015441 SharkBite 2" x 1-1/2" Reducing CouplingSB0235 SharkBite 1-1/4" Elbow 90°SB0241 SharkBite 1-1/2" Elbow 90°SB0254 SharkBite 2" Elbow 90°SB0335 SharkBite 1-1/4" Slip TeeSB03353516 SharkBite 1-1/4" x 1-1/4" x 1/2" Reducing Slip TeeSB03353522 SharkBite 1-1/4" x 1-1/4" x 3/4" Reducing Slip TeeSB03353528 SharkBite 1-1/4" x 1-1/4" x 1" Reducing Slip TeeSB0341 SharkBite 1-1/2" Slip TeeSB03414122 SharkBite 1-1/2" x 1-1/2" x 3/4" Reducing Slip TeeSB03414128 SharkBite 1-1/2" x 1-1/2" x 1" Reducing Slip TeeSB03414135 SharkBite 1-1/2" x 1-1/2" x 1-1/4" Reducing Slip TeeSB0354 SharkBite 2" Slip TeeSB03545428 SharkBite 2" x 2" x 1" Reducing Slip TeeSB03545435 SharkBite 2" x 2" x 1-1/4" Reducing Slip TeeSB03545441 SharkBite 2" x 2" x 1-1/2" Reducing Slip TeeSB0435 SharkBite 1-1/4" End CapSB0441 SharkBite 1-1/2" End CapSB0454 SharkBite 2" End CapSB0535 SharkBite 1-1/4" Elbow 45°SB0541 SharkBite 1-1/2" Elbow 45°SB0554 SharkBite 2" Elbow 45°SB0635 SharkBite 1-1/4" Slip CouplingSB0641 SharkBite 1-1/2" Slip CouplingSB0654 SharkBite 2" Slip CouplingSB0835 SHARKBITE 2XL 1-1/4" TEE SB08353516 SB 2XL 1-1/4" x 1-1/4" x 1/2" REDG TEESB08353522 SB 2XL 1-1/4" x 1-1/4" x 3/4" REDUCING TEESB08353528 SB 2XL 1-1/4" x 1-1/4" x 1" REDUCING TEESB0841 SHARKBITE 2XL 1-1/2" TEESB08414122 SB 2XL 1-1/2" x 1-1/2" x 3/4" REDG TEESB08414128 SB 2XL 1-1/2" x 1-1/2" x 1" REDG TEESB08414135 SHARKBITE 2XL 1-1/2" x 1-1/2" x 1-1/4" REDG TEESB0854 SHARKBITE 2XL 2" TEE SB08545428 SHARKBITE 2XL 2" x 2" x 1" REDUCING TEESB08545435 SHARKBITE 2XL 2" x 2" x 1-1/4" REDUCING TEESB08545441 SHARKBITE 2XL 2" x 2" x 1-1/2" REDUCING TEESB113532F SharkBite Connector 1-1/4" x 1-1/4"F NPTSB113532M SharkBite Connector 1-1/4" x 1-1/4"M NPTSB114140F SharkBite Connector 1-1/2" x 1-1/2"F NPTSB114140M SharkBite Connector 1-1/2" x 1-1/2"M NPTSB115450F SharkBite Connector 2" x 2"F NPTSB115450M SharkBite Connector 2" x 2"M NPT

Page 4




SU9018 Valve Connector 1/2" SU9019 Valve Connector 3/4" SU9020 Valve Connector 1"SU9023 Valve Connector 1/2"SU9025 Valve Connector 3/4" U004 Coupling 1/4" SB x 1/4" SBU006 Coupling 3/8" x 3/8"U006LF Coupling Straight 3/8" x 3/8" LFU008 Straight Connector 1/2" x 1/2"U008LF Coupling Straight 1/2" x 1/2" - LFU009 Reducing Coupling 3/8" x 1/2"U009LF Coupling Reducing 1/2" x 3/8" LFU012 Straight coupling 5/8" x 5/8"U012LF Coupling Straight 5/8" x 5/8" - LFU016 Straight Connector 3/4" x 3/4"U016LF Coupling Straight 3/4" x 3/4" - LFU020 Straight Coupling 1" x 1"U020LF Coupling Straight 1" x 1" - LFU057 Reducing Coupling 5/8" x 3/4"U057LF Coupling Reducing 3/4" x 5/8" - LFU058 Straight Connector Reducing 3/4" x 1/2"U058LF Coupling Reducing 3/4" x 1/2" - LFU060 1" x 3/4" Reducing CouplingU060LF Coupling Reducing 1" x 3/4" - LFU066 Connector Straight Male 1/4" x 1/2" FNPTU068 Connector 1/2" SB x 3/4" FNPTU068LF Connector Straight 1/2" x 3/4" F NPT - LFU070 Connector Straight Female 3/8" x 1/2" T NPTU070LF Connector 3/8" x 1/2" FNPT - LFU072 Straight Connector 1/2" x 1/2" FNPTU072LF Connector Straight 1/2" x 1/2" F NPT - LFU088 Straight Connector 3/4" x 3/4" FNPTU088LF Connector Straight 3/4" x 3/4" F NPT - LFU092 3/4" x 112" FNPT Connector U092LF SharkBite 3/4" x 1/2" FNPT Connector" LFU094 Straight Connector 1" x 1" NPT FEMALEU094LF Connector Straight 1" x 1" F NPT - LFU110 Connector Straight Male 1/4" SB x 1/2" MNPTU116 Connector Straight Male 1/2" x 3/4" M NPTU116LF Connector Straight 1/2" x 3/4" M NPT - LFU118 Connector Straight Male 3/8" x 1/2" M NPTU118LF Connector 3/8" x 1/2" MNPT - LFU120 Straight Connector 1/2" x 1/2" MNPTU120LF Connector Straight 1/2" x 1/2" M NPT - LFU126 Straight connector 5/8" x 3/4" M NPTU126LF Connector 5/8" 3/4" MNPT - LFU134 Straight Connector 3/4" x 3/4" MNPTU134LF Connector Straight 3/4" x 3/4" M NPT - LF

Page 5




U138 3/4" x 1/2" MNPT Connector 3217 17768U138LF Connector 3/4" x 1/2" M NPT LFU139 SharkBite 3/4” x 1” MNPT Connector - LFU140 Straight Connector 1" x 1" NPT MALEU140LF Connector Straight 1" x 1" M NPT - LFU142 Straight Connector 1" x 3/4" NPT MALEU142LF Connector Straight 1" x 3/4" M NPT - LFU2008 Check Valve 1/2"U2008LF Check Valve Body 1/2" x 1/2" - LFU2016 Check Valve 3/4"U2016LF Check Valve Body 3/4" x 3/4" - LFU2020 Check Valve 1"U2020LF Check Valve Body 1" x 1" - LFU244 Elbow 1/4" SBU246 Elbow 3/8" x 3/8"U246LF Elbow 3/8" x 3/8" - LFU248 Elbow 1/2" x 1/2"U248LF Elbow 1/2" x 1/2" - LFU249 1/2" SB x 1/2" SB Drop Ear ElbowU249LF Elbow Low Ear 1/2" x 1/2" - LFU252 Elbow 5/8" X 5/8"U252LF Elbow 5/8" x 5/8" LFU256 Elbow 3/4" x 3/4"U256LF Elbow 3/4" x 3/4" - LFU260 Elbow 1" x 1"U260LF Elbow 1" x 1" - LFU272 1/2" x 3/8" Reducing ElbowU272LF SharkBite 1/2" x 3/8" Reducing Elbow - LFU273 Reducing elbow 5/8" x 3/4"U273LF Elbow Reducing 3/4" x 5/8" - LFU274 Elbow Reducing 3/4" x 1/2"U274LF Elbow Reducing 3/4" x 1/2" - LFU276 Connector Elbow 1/4" SB x 3/8" MIPU280 Elbow 1/2" x 1/2" MNPTU280LF Elbow 1/2" x 1/2" M NPT - LFU3006 Slip Coupling 3/8"U3006LF Slip Coupling 3/8" LFU3008 Slip Coupling 1/2"U3008LF Slip Coupling 1/2" x 1/2" - LFU3016 Slip Coupling 3/4"U3016LF Slip Coupling 3/4" x 3/4" - LFU3020 Slip Coupling 1"U3020LF Slip Coupling 1" x 1" - LFU304 Connector Elbow 1/4" SB x 1/2" FNPTU3072LF Union Tail Piece 1/2" - LFU308 Elbow 1/2" x 1/2" FNPTU3088LF Union Tail Piece 3/4" LFU308LF Elbow 1/2" x 1/2" F NPT - LF

Page 6




U3094 Union Tailpiece 1"U3094LF Union Tail Piece 1"" LFU332 Drop Ear Elbow 3/8" x 1/2" F NPTU332LF Elbow Drop Ear 3/8" x 1/2" FNPT LFU334 Elbow Lugged G 1/2" x 1/2"U334LF Elbow Lugged 1/2" x 1/2" F NPT - LFU335 Hy-ear Elbow 1/2"U335LF Elbow Hi Ear 1/2" x 1/2" F NPT - LFU3362LF Slip Tee 1/2" x 1/2" x 1/2" - LFU3370LF Slip Tee 3/4" x 3/4" x 3/4" - LFU340 Drop Ear Elbow 3/4" x 3/4" F NPTU340LF Elbow Lugged Drop Ear 3/4" x 3/4" FNPT - LFU3482LF Slip Tee 1/2" x 1/2" x 1/2" F NPT - LFU3486LF Slip Tee 3/4" x 3/4" x 3/4" F NPT - LFU350 Elbow Lugged ext. G 1/2" x 1/2"U350LF Elbow Lugged 1/2" x 1/2" BP EXT - LFU352 1/2" x 1/2" CTS Back Plated Stub OutU352 Elbow Lugged ext. 100 G 1/2" x 1/2"U3523 Connector Straight Cistern Stop 1/4" SB x 9/16-24 UNEFU3524LF Stop valve Connector 1/4" SB x 7/16" - 28 UNEFU3525 Connector Straight Faucet 1/4" SB x 1/2"F-14 NPSMU352LF 1/2" SharkBite x 1/2" CTS Back Plated Stub Out - LFU352LF Elbow Lugged 1/2" x 1/2" BP EXT 100mm Long – LFU3531 Connector Straight Ball Cock 1/4" SB x 7/8"U3537 Connector Straight Ball Cock 1/4" SB x 7/8"U3558 Supply Stop 1/4" Tee adaptorU358 Tee 1/4" SBU360 Tee 3/8" x 3/8" x 3/8"U360LF Tee 3/8" x 3/8" x 3/8" LFU362 Tee 1/2" x 1/2" x 1/2"U362LF Tee 1/2" x 1/2" x 1/2" - LFU363 Reducing Tee 1/2" x 1/2" x 3/8"U363LF Tee Conversion 1/2" x 1/2" x 3/8" - LFU364 Bull Nose Tee 3/8" x 3/8" x 1/2"U364LF Tee Conversion 3/8" X 3/8" x 1/2" - LFU366 Tee 5/8" x 5/8" x 5/8"U366LF Tee 5/8" x 5/8" x 5/8" - LFU370 Tee 3/4" x 3/4" x 3/4"U370LF Tee 3/4" x 3/4" x 3/4" - LFU374 Tee 1" x 1" x 1"U374LF Tee 1" x 1"x 1"-LFU412 Tee 3/4" x 3/4" x 1/2"U412LF Tee 3/4" x 3/4" x 1/2" - LFU416 Tee 1" x 1" x 3/4"U416LF Tee 1" x 1"x 3/4"-LFU444 Tee 3/4" x 1/2" x 3/4"U444LF Tee 3/4" x 1" x 3/4 "-LFU4482LF Slip Tee 1/2"SB x 1/2"SB x 1/2" Tail - LF

Page 7




U454 Tee 3/4" x 1/2" x 1/2"U454LF Tee 3/4" x 1/2" x 1/2" - LFU512 Cap 3/8"U512LF End Stop 3/8" - LFU514 Stop End 1/2"U514LF End Stop 1/2" - LFU516 Stop End 5/8"U516LF End Stop 5/8" LFU518 Stop End 3/4"U518LF End Stop 3/4" - LFU520 1" Stop EndU520LF End Stop 1" – LFU668 Valve Adaptor 3/8" x 1/2" M SpecialU668LF Connector 3/8" x 1/2" NPSM - LFU670 Valve Adaptor 1/2" x 1/2" M SpecialU670LF Connector 1/2" x 1/2" NPSM LFU672 Valve Adaptor 3/4" x 1/2" M SpecialU672LF Connector 3/4" x 1/2" NPSM LFU674 Valve Adaptor 1" x 1/2" M SpecialU674LF Connector 1" x 1/2" NPSM - LFU719 SB to Tail OD reducer 3/8" x 1/2" TailU719LF Adaptor 3/8" x 1/2" Tail- LFU720 Reducer Straight 3/4" Tail x 1/2" CartridgeU720LF Adaptor 1/2" x 3/4" Tail - LFU721 SB to Tail OD reducer 3/8" x 3/4" TailU721LF Adaptor 3/8" x 3/4" Tail" LFU722 Reducer Straight 1" Tail x 1/2" CartridgeU722LF Adaptor 1/2" x 1" Tail- LFU724 Reducer Straight 1" Tail x 3/4" CartridgeU724LF Adaptor 3/4" x 1" Tail - LFU9002 Forged Adaptor Clack 1"U9002LF Adaptor Clack 1" - LFU9003 Forged Adaptor Clack 3/4"U9003LF Adaptor Clack 3/4" - LFU9005 1/2" Threaded Valve Adapter U9005LF SharkBite 1/2" Threaded Valve Adapter - LFUF12128A 3/4” x 3/4” SharkBite x 1/2” FNPT Sprinkler Angled Adapter UF12128H 3/4” x 3/4” SharkBite x 1/2” FNPT Sprinkler Tee (Horizontal) UF12128V 3/4” x 3/4” SharkBite x 1/2” FNPT Sprinkler Tee (Vertical) UF128L 3/4” SharkBite x 1/2” FNPT Left Hand Elbow Sprinkler UF128R 3/4” SharkBite x 1/2” FNPT Right Hand Elbow Sprinkler UF128S 3/4” SharkBite x 1/2” FNPT Sprinkler Straight UF128U 3/4” SharkBite x 1/2” FNPT Sprinkler Elbow Up UF16128H 1” x 3/4”SharkBite x 1/2” FNPT Sprinkler Tee (Horizontal) UF16128V 1” x 3/4” SharkBite x 1/2” FNPT Sprinkler Tee (Vertical) UF16168H 1” x 1” SharkBitex 1/2” FNPT Sprinkler Tee (Horizontal) UF16168V 1” x 1” SharkBite x 1/2” FNPT Sprinkler Tee (Vertical) UF168L 1” SharkBite x 1/2” FNPT Left Hand Elbow Sprinkler

Page 8




UF168R 1” SharkBite x 1/2” FNPT Right Hand Elbow SprinklerUF168U 1” SharkBite x 1/2” FNPT Sprinkler Elbow Up

Page 9




ICC-ES Report PMG-1149Reissued 08/2016

This report is subject to renewal 08/2017

EVALUATION SUBJECT:

PUSH FIT FITTINGS

DIVISION: 22 00 00—PLUMBING

SECTION: 22 11 16—DOMESTIC WATER PIPING

Report Holder:

ELKHART PRODUCTS CORPORATION 1255 OAK STREET ELKHART, IN 46515

Listings are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the listing or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this listing, or as to any product covered by the listing. Copyright © 2016 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 6

ICC-ES PMG Listing PMG-1149 Effective Date: August 2016 This listing is subject to re-examination in one year.

www.icc-es-pmg.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council®

CSI: Division: 22 00 00—PLUMBING Section: 22 11 16—Domestic Water Piping

Product certification system: The ICC-ES product certification system includes testing samples taken from the market or supplier’s

stock, or a combination of both, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of the supplier’s quality system

Product: Push Fit Fitting with quick assembly push fit mechanism for copper, PEX and CPVC tubing and Pipes

Listee: Elkhart Products Corporation

1255 Oak Street Elkhart, IN 46515 www.elkhartproducts.com

Compliance with the following codes:

2015, 2012, 2009 and 2006 International Plumbing Code® (IPC) 2015, 2012, 2009 and 2006 International Residential Code® (IRC) 2015, 2012, 2009 and 2006 Uniform Plumbing Code® (UPC)* 2011 Uniform Plumbing Code - India™ (UPC-1)* *Uniform Plumbing Code is a copyrighted publication of the International Association of Plumbing and Mechanical Officials

Compliance with the following standards:

ASSE 1061-2011, Performance Requirements for Push-fit Fittings ICC-ES LC1009 (April 2010), PMG Listing Criteria for Push-Fit Fittings for Potable Water Tube and Radiant Heating Systems NSF/ANSI 61-2014a, Drinking Water Systems Components—Health Effects

Identification:

Manufacturer's name or trademark, nominal size, tubing material for which the fitting is intended and the ICC-ES PMG certification mark must be visible after installation. NOTE: For fittings 3/4” and smaller, the tubing material can be indicated on packaging literature.

Installation:

The Elkhart Products Corporation push-fit fittings described in this listing must be installed in accordance with the manufacturer’s published installation instructions and the applicable codes. Installation is limited to seamless rigid copper tubing complying with ASTM B 88 as well as PEX and CPVC tubing and Pipes. Prior to installation of the fitting, the end of the copper tubing must be

PMG-1149 | Most Widely Accepted and Trusted Page 2 of 6

inspected to ensure that it is cut square and is not dented or oval or have flat spots. The end of the tubing must be reamed on the inside to ensure proper flow, and chamfered on the outside to remove any burrs that might damage the EPDM seal of the Elkhart Products Corporation fitting.

Models:

TECTITE

Model No. Description Sizes

55463 Reducer Female Adapter 203-1/2x3/4

55465 Reducer Male Adapter 204-1/2x3/4

69900 Coupling w/ Stop 200-1/2


69904 Coupling w/ Stop 200-1

69906 Reducer Coupling 201-3/4x1/2

69908 Reducer Coupling 201-1x3/4

69910 Slip Coupling 201-1/2


69914 Slip Coupling 201-1

69916 Female Adapter 203-1/2


69920 Female Adapter 203-1

69922 Male Adapter 204-1/2


69926 Male Adapter 204-1

69928 Reducer Male Adapter 204-1x3/4

69930 90 Deg. Elbow 207-1/2

69932 90 Deg. Elbow 207-3/4

69934 90 Deg. Elbow 207-1

69936 90 Deg. Reducer Elbow 207-3/4x1/2

69966 Tube Cap 217-1/2

69968 Tube Cap 217-3/4

69970 Tube Cap 217-1



88011 Coupling w/ Stop 200-1 1/4

88013 Coupling w/ Stop 200-1 1/4 LL


88015 90 Deg. Elbow 207-1/2

88016 Coupling w/ Stop 200-1 1/2


88019 Coupling w/ Stop 200-1 1/2 LL

88020 90 Deg. Elbow 207-3/4

88021 90 Deg. Elbow 207-2

88022 90 Deg. Elbow 207-1 1/2

88023 90 Deg. Elbow 207-1 ¼

88024 90 Deg. Elbow 207-1


88026 Male Adapter 204-1 ¼

88027 Male Adapter 204-1 ½


88029 Coupling w/ Stop 200-2 LL



88031 45 Deg. Street Elbow 2062-2

88032 90 Deg. Elbow 207-1 1/4 LL

88033 45 Deg. Elbow 206-2



88036 90 Deg. Elbow 207-1 1/2 LL



88042 Female Adapter 203-1 ½

88043 Female Adapter 203-1 ¼


88045 Tube Cap 217-1/2

88046 90 Deg. Elbow 207-2 LL

88048 Female Adapter 203-1 1/4 LL

88050 Tube Cap 217-3/4

88051 45 Deg. Elbow 206-1 ¼

88052 45 Deg. Elbow 206-1 ¼

88053 Tube Cap 217-1 ¼

88054 Tube Cap 217-1

88055 90 Deg. Drop Ear Elbow 2707-3-5-1/2

88056 45 Deg. Street Elbow 2062-1 ¼

88057 Tube Cap 217-1 ½

88058 Female Adapter 203-1 1/2 LL

88059 Tube Cap 217-2

88064 Female Adapter 203-2 LL

88066 Male Adapter 204-1 1/4 LL

88069 Male Adapter 204-1 1/2 LL

88072 45 Deg. Street Elbow 2062-1 ½

88075 Reducer Coupling 201-3/4x1/2

88078 Reducer Coupling 201-1x3/4

88080 Reducer Male Adapter 204-3/4x1



88088 Slip Coupling 201-1

88090 Male Adapter 204-2 LL

88092 45 Deg. Elbow 206-1 1/4 LL

88095 45 Deg. Elbow 206-1 1/2 LL

88097 45 Deg. Elbow 206-2 LL

88112 45 Deg. Street Elbow 2062-1 1/4 LL

88114 45 Deg. Street Elbow 2062-1 1/2 LL

88116 45 Deg. Street Elbow 2062-2 LL

88130 Tube Cap 217-1 1/4 LL

88132 Tube Cap 217-1 1/2 LL

88134 Tube Cap 217-2 LL


QTITE

Model No. Description Sizes 70000 Coupling w/ Stop 900-1/2 70005 Coupling w/ Stop 900-3/4 70010 Coupling w/ Stop 900-1 70030 Reducer Coupling 901-3/4x1/2 70035 Reducer Coupling 901-1x1/2 70040 Reducer Coupling 901-1x3/4 70050 Reducer Coupling 901-1 1/4x3/4 70055 Reducer Coupling 901-1 1/4x1 70060 Reducer Coupling 901-1 1/2x3/4 70065 Reducer Coupling 901-1 1/2x1 70070 Reducer Coupling 901-1 1/2x1 1/4 70085 Reducer Coupling 901-2x1 1/2 70090 Female Adapter 903-1/2 70095 Female Adapter 903-3/4 70100 Female Adapter 903-1 70105 Female Adapter 903-1 1/4 70110 Female Adapter 903-1 1/2 70115 Female Adapter 903-2 70120 Male Adapter 904-1/2 70125 Male Adapter 904-3/4 70130 Male Adapter 904-1 70135 Male Adapter 904-1 1/4 70140 Male Adapter 904-1 1/2 70145 Male Adapter 904-2 70150 90 Deg. Elbow 907-1/2 70155 90 Deg. Elbow 907-3/4 70160 90 Deg. Elbow 907-1 70195 90 Deg. Street Elbow 9072-1 1/4 70200 90 Deg. Street Elbow 9072-1 1/2 70205 90 Deg. Street Elbow 9072-2 70225 90 Deg. CxM Elbow 907-4-1 1/4 70230 90 Deg. CxM Elbow 907-4-1 1/2 70235 90 Deg. CxM Elbow 907-4-2 70255 90 Deg. CxF Elbow 907-3-1 1/4 70260 90 Deg. CxF Elbow 907-3-1 1/2 70265 90 Deg. CxF Elbow 907-3-2 70270 90 Deg. Drop Ear Elbow 9707-3-5-1/2 70275 45 Deg. Elbow 906-1/2 70280 45 Deg. Elbow 906-3/4 70285 45 Deg. Elbow 906-1 70290 45 Deg. Elbow 906-1 1/4 70295 45 Deg. Elbow 906-1 1/2 70300 45 Deg. Elbow 906-2 70320 45 Deg. Street Elbow 9062-1 1/4 70325 45 Deg. Street Elbow 9062-1 1/2 70330 45 Deg. Street Elbow 9062-2 70340 Nominal Tee 911-3/4 70345 Nominal Tee 911-1 70365 Reducer Tee 911-3/4x3/4x1/2 70370 Reducer Tee 911-1x1x1/2 70375 Reducer Tee 911-1x1x3/4 70390 Reducer Tee 911-1 1/4x1 1/4x1


70395 Reducer Tee 911-1 1/2x1 1/2x3/4 70400 Reducer Tee 911-1 1/2x1 1/2x1 70405 Reducer Tee 911-1 1/2x1 1/2x1 1/4 70410 Reducer Tee 911-2x2x1 70415 Reducer Tee 911-2x2x1 1/4 70420 Reducer Tee 911-2x2x1 1/2 70445 Reducer Tee 911-1 1/4x3/4x1 1/4 70450 Reducer Tee 911-1 1/4x1x1 1/4 70455 Reducer Tee 911-1 1/2x3/4x1 1/2 70505 Reducer Tee 911-1 1/4x3/4x3/4 70520 Reducer Tee 911-1 1/2x1x1 70545 Tube Cap 917-1/2 70550 Tube Cap 917-3/4 70555 Tube Cap 917-1 70560 Tube Cap 917-1 1/4 70565 Tube Cap 917-1 1/2 70570 Tube Cap 917-2 65824 PEX Liner 1/2 65828 PEX Liner 3/4 65832 PEX Liner 1

Low Lead Models:

Model No. Description Sizes

10188013 CxC Coupling W/Stop 1-1/4"

10188019 CxC Coupling W/Stop 1-1/2"

10188029 CxC Coupling W/Stop 2"

10188032 CxC 90 Deg. Elbow 1-1/4"

10188036 CxC 90 Deg. Elbow 1-1/2"

10188046 CxC 90 Deg. Elbow 2"

10188048 CxF Adapter 1-1/4"

10188058 CxF Adapter 1-1/2"

10188064 CxF Adapter 2"

10188066 CxM Adapter 1-1/4"

10188069 CxM Adapter 1-1/2"

10188090 CxM Adapter 2"

10188092 CxC 45 Deg. Elbow 1-1/4"

10188095 CxC 45 Deg. Elbow 1-1/2"

10188097 CxC 45 Deg. Elbow 2"

10188107 CxCxC Tee 1-1/4"

10188109 CxCxC Tee 1-1/2"

10188112 Ftg. x C 45 Deg St. Elbow 1-1/4"

10188114 Ftg. x C 45 Deg St. Elbow 1-1/2"

10188116 Ftg. x C 45 Deg St. Elbow 2"

10188117 CxCxC Tee 1-1/4" x 1-1/4" x 1"

10188119 CxCxC Tee 1-1/2" x 1-1/2" x 3/4"

10188120 CxCxC Tee 1-1/2" x 1-1/2" x 1"

10188122 CxCxC Tee 1-1/2" x 1-1/2" x 1-1/4"

10188124 CxCxC Tee 2" x 2" x 1"

10188125 CxCxC Tee 2"

10188126 CxCxC Tee 2" x 2" x 1-1/4"


10188127 CxCxC Tee 1-1/4" x 1-1/4" x 1/2"

10188128 CxCxC Tee 2" x 2" x 1-1/2"

10188129 CxCxC Tee 1-1/4" x 1-1/4" x 3/4"

10188130 Cap 1-1/4"

10188132 Cap 1-1/2"

10188134 Cap 2" Conditions of Listing:

1. Elkhart Products Corporation’s Push-fit fittings are limited to interior, above-grade installations where the fittings are not embedded in concrete.

2. Elkhart Products Corporation’s Push-fit fittings and connected tubing must not be used to support any load beyond that of the water-filled pipe and fittings.

3. The potable water distribution system utilizing the Elkhart Products Corporation’s push-fit fittings must be pressure-tested and inspected in accordance with Section 312.5 of the International Plumbing Code® or Section P2503.7 International Residential Code®, as applicable.

4. The Elkhart Products Corporation’s Push-fit fittings are manufactured in Elkhart and Geneva, Indiana under a quality control program with annual inspection by ICC-ES.

rowlatd

Highlight

Q&A Consistency Meeting Agenda for Plumbing, September … · Q&A Consistency Meeting Agenda for Plumbing, September 2016 1. Question: Can condensate drainage piping from HVAC equipment

Documents