PSK Standardisointi STANDARDI PSK 4202 PSK Standards Association Ehdotus 11 E10C1A 4. painos/4 th edition COPYRIGHT: PSK Standardisointiyhdistys ry 2021-02-20 1 (17) MYYNTI: PSK Standardisointiyhdistys ry, PUH. (09) 72 880 880 WWW-OSOITE: www.psk-standardisointi.fi, SÄHKÖPOSTI [email protected]Korvaa standardin PSK 4202:2017 Replaces the standard 4202:2017 PUTKILUOKKA E10C1A PAINELAITEKÄYTTÖÖN. KUUMALUJA SEOSTAMATON TERÄS. HITSATTU TERÄSPUTKI Pipe class E10C1A for pressure purposes. Welded non-alloy steel pipe for elevated temperatures Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail. Sisällys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5 Putkiluokan sallitut käyttöpaineet ja lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the standard 1 SOVELTAMISALA 1 SCOPE Tässä standardissa esitetään putkiluokkaan E10C1A kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 10 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C. This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E10C1A, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 10 bar and the maximum allowable temperature is 400 °C. Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480- 2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia. The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5. 2 VIITTAUKSET 2 REFERENCES PSK 4201 Putkiluokat. Määrittely. 2021 PSK 4201 Pipe classes. Definition. 2021 SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018 SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2018 SFS-EN 1514-1:en Laipat ja yhteet. PN- mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei- metalliset tasotiivisteet. 1997 SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
136
Embed
PSK Standardisointi STANDARDI PSK 4202 PSK Standards … · 2021. 2. 22. · SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Korvaa standardin PSK 4202:2017 Replaces the standard 4202:2017 PUTKILUOKKA E10C1A PAINELAITEKÄYTTÖÖN. KUUMALUJA SEOSTAMATON TERÄS. HITSATTU TERÄSPUTKI Pipe class E10C1A for pressure purposes. Welded non-alloy steel pipe for elevated temperatures
Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail.
Sisällys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5 Putkiluokan sallitut käyttöpaineet ja lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and
temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the standard
1 SOVELTAMISALA
1 SCOPE
Tässä standardissa esitetään putkiluokkaan E10C1A kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 10 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C.
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E10C1A, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 10 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5.
2 VIITTAUKSET
2 REFERENCES
PSK 4201 Putkiluokat. Määrittely. 2021
PSK 4201 Pipe classes. Definition. 2021
SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018
SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2018
SFS-EN 1514-1:en Laipat ja yhteet. PN-mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei-metalliset tasotiivisteet. 1997
SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
SFS-EN 10028-2:2017 Painelaiteteräkset. Levy-tuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004
SFS-EN 10217-2:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Sähkövastushitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-2:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions- Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10217-5:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 5: Jauhekaarihitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-5:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions. Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset teräkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020:en Metallic industrial piping. Part 3: Design and calculation. 2017
SFS-EN 13480-4:2017 Metalliset teollisuusputkistot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
PSK Standardisointi PSK 4202 E10C1A 3 (17)
SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
SFS-EN ISO 898-1 Kiinnityselimien lujuusominaisuudet. Seostamattomat ja seos-teräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032:en Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032:en Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Normaalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT 3 MATERIALS
Tähän putkiluokkaan kuuluvien DN 15…500 putkien materiaali on seostamaton teräs P235GH, SFS-EN 10217-2.
The material of pipes DN 15…500 belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10217-2.
Putkien DN 600...1200 materiaali on P235GH, SFS-EN 10217-5.
The material of pipes DN 600...1200 is P235GH, SFS-EN 10217-5.
Käyrien, kartioiden, päätyjen ja T-putkien materiaali on seostamaton teräs P235GH, SFS-EN 10253-2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standardin SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistus-vaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an authorized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
Putkenosien mukana on lisäksi toimitettava valmistajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
PSK Standardisointi PSK 4202 E10C1A 4 (17)
4 MITAT
4 DIMENSIONS
Putkiluokkaan E10C1A kuuluvien putkien ja put-kenosien mitat ja mittastandardit on esitetty taulu-koissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E10C1A are shown in Tables 1, 2 and 3.
Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama liitospäissä ja osan keskellä. Seinämät voidaan tarvittaessa viistää hitsauspäissä vastaamaan liittyvää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, mutterien, aluslaattojen ja tiivisteiden mittastandardit ja materiaalit Table 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts, washers and gaskets
Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Nimike Designation
Standardi Standard
Todistus Certificate
Kauluslaippa PN 10 Welding neck flange PN 10
SFS-EN 1092–1, tyyppi 11-B1 SFS-EN 1092–1, type 11-B1
P250GH SFS-EN 10222-2 3.1
Umpilaippa PN 10 Blind flange PN 10
SFS-EN 1092–1, tyyppi 05 SFS-EN 1092–1, type 05
P265GH SFS-EN 10028-2 3.1
Sokeointilevy Spade
PSK 7820 P265GH SFS-EN 10028-2 3.1
Kierteelliset putkenosat 4) 5)
Threaded pipe fittings SFS-EN 10241 P235GH tai / or
P250GH SFS-EN 10273 SFS-EN 10222-2
3.1
Ruuvi 3) 4)
Bolt
SFS-EN ISO 4014 25CrMo4 5.6 1) (T < 50 °C)
SFS-EN 10269 SFS-EN ISO 898-1
3.1 2.2
Mutteri 3) 4)
Nut SFS-EN ISO 4032
25CrMo4 5 (T ≤ 50 °C)
SFS-EN 10269 SFS-EN ISO 898-2
3.1 2.2
Aluslaatta 3)
Washer SFS-EN ISO 7089 Grade A S235JR tai vastaava
/ or equal SFS-EN 10025-2 -
Tiiviste PN 10 Gasket PN 10
SFS-EN 1514-1, tyyppi IBC SFS-EN 1514-1, type IBC
2) - -
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201. Ruuvin lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella. 3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole vaikutusta
mekaanisiin ominaisuuksiin. 4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin materiaalin
valmistajan antamiin materiaalitodistuksiin. 5) Kierteellisten putkenosien suurin suositeltava nimelliskoko on DN 50. 1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4. See standard
PSK 4201. Starting material shall comply with requirements in SFS-EN 10269. 2) The gasket material and thickness are determined by the fluid and process conditions. 3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C but this has
no effect on mechanical properties. 4) The fittings or their packages must have markings, by which the fittings can be connected to related material certificates
given by the supplier. 5) The maximum recommended size for threaded pipe fittings is DN 50.
PSK Standardisointi PSK 4202 E10C1A 11 (17)
5 PUTKILUOKAN SALLITUT KÄYTTÖPAINEET JA LÄMPÖTILAT
5 THE ALLOWABLE OPERATING PRESSURES AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 10 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen.
The pipes and fittings belonging to this pipe class have been designed to resist 10 bar overpressure in 20 °C temperature and the maximum allowable temperature is 400 °C. The vacuum resistance is according to standard PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa on esitetty kuvassa 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan kertomalla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 10) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 10).
Yli 400 °C lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4202 E10C1A 12 (17)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 Allowable pressures (bar) as a function of temperature Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 10). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine. Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN 10). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
1) Haaroituksen kulma on 90° ± 5°. Haaroituksen molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon. 1) The angle of the branch connection is 90° ± 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in.
PSK Standardisointi PSK 4202 E10C1A 14 (17)
OPASTAVIA TIETOJA
INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet
O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille:
General calculation criteria for piping components of pipe class:
- mitoitus SFS-EN 13480-3 mukaan - dimensioning in accordance with SFS-EN 13480-3
- ylipaine 1,0 MPa - overpressure 1,0 MPa - lämpötila 20 °C - temperature 20 °C - suunnittelujännitys f = 150 MPa - design stress f = 150 MPa - korroosiovara c0 = 1,0 mm - corrosion allowance c0 = 1,0 mm - hitsausliitoksen lujuuskerroin z = 1,0 - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmistustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
putket: pipes: - 10 % tai 0,3 mm, kun T ≤ 5,0 mm - 10 % or 0,3 mm, when T ≤ 5,0 mm - 8 %, kun T > 5,0 mm
- 8 %, when T > 5,0 mm
käyrät, kartiot, T-putket ja päädyt: elbows, reducers, tee pieces and caps: - 12,5 %, kun DN ≤ 600 - 12,5 %, when DN ≤ 600 - 0,35 mm, kun DN > 600 ja T ≤ 10,0 mm - 0,35 mm, when DN > 600 and T ≤ 10,0 mm - 0,5 mm, kun DN > 600 ja T > 10,0 mm
- 0,5 mm, when DN > 600 and T > 10,0 mm
Kartioiden laskenta on tehty epäkeskeisille kartioille. Kartiot on laskettu muovattuina DN 500:aan asti ja levykartioina DN 600:sta ylöspäin.
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and upwards from DN 600 as straight reducers.
PSK Standardisointi PSK 4202 E10C1A 15 (17)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4202 E10C1A 16 (17)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
- Gasket DN 100 - PN 10 - type IBC - 1,5 mm - SFS-EN 1514-1 - graphite laminate 2)
1) E = epäkeskeinen, K = keskeinen 2) Tiivistemateriaalin valinta ja tiivisteen paksuus
määräytyvät virtaavan aineen ja prosessiolo-suhteiden mukaan.
1) E = eccentric, K = concentric 2) The selection of the gasket material and thickness
shall be determined by the fluid and process conditions
PSK Standardisointi PSK 4202 E10C1A 17 (17)
O.4 Putkiluokan tunnus
O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokan merkintää.
The letter E in the beginning of the identification of the pipe class shows, that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältö poikkeaa tässä standardissa esitetystä.
A different identification shall be given to the pipe class, if the contents deviate from this standard.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting materials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been replaced by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- Nimelliskokojen DN600…1200 komponenttien mittoja on korjattu vastaamaan viitestandardien mittoja
- The dimensions of components in nominal sizes DN600…1200 have been revised to comply with reference standards
- Putkiluokan suunnittelujännitys f kohdassa O.1 muutettu.
- The design stress f in section O.1 has been changed
- Kuva 1 ja taulukko 4 on muutettu vastaamaan uutta suunnittelujännityksen arvoa.
- Figure 1 and table 4 have been revised to match the new design stress
Korvaa standardin PSK 4203:2017 Replaces the standard PSK 4203:2017 PUTKILUOKKA E10C1B PAINELAITEKÄYTTÖÖN. KUUMALUJA SEOSTAMATON TERÄS. SAUMATON TERÄSPUTKI Pipe class E10C1B for pressure purposes. Seamless non-alloy steel pipe for elevated temperatures
Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail.
Sisällys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5 Putkiluokan sallitut käyttöpaineet ja lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and tempera-tures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the standard
1 SOVELTAMISALA 1 SCOPE
Tässä standardissa esitetään putkiluokkaan E10C1B kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putki-luokan paineenkestävyys. Tämän putkiluokan suu-rin sallittu paine on 10 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E10C1B, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at tem-perature 20°C is 10 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be tak-en into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5.
2 VIITTAUKSET 2 REFERENCES
PSK 4201 Putkiluokat. Määrittely. 2021
PSK 4201 Pipe classes. Definition. 2021
SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varus-teille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018
SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accesso-ries, PN designated. Part 1: Steel flanges. 2018
SFS-EN 1514-1:en Laipat ja yhteet. PN-mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei-metalliset tasotiivisteet. 1997
SFS-EN 1514-1:en Flanges and their joints. Dimen-sions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
PSK Standardisointi PSK 4203 E10C1B 2 (16) SFS-EN 10028-2:2017 Painelaiteteräkset. Levy-tuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004
SFS-EN 10216-2:2014 + A1:2019 Saumattomat painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Kuumalujat seostamattomat ja seostetut teräs-putket. 2014
SFS-EN 10216-2:2014 + A1:2019:en Seamless steel tubes for pressure purposes. Technical delivery conditions. Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties. 2014
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset te-räkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020:en Metallic industrial piping. Part 3: Design and calculation. 2017
SFS-EN 13480-4:2017 Metalliset teollisuusputkis-tot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
SFS-EN ISO 898-1 Kiinnityselimien lujuusomi-naisuudet. Seostamattomat ja seosteräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fas-teners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
PSK Standardisointi PSK 4203 E10C1B 3 (16) SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032:en Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032:en Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Nor-maalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT 3 MATERIALS
Tähän putkiluokkaan kuuluvien putkien materiaali on seostamaton teräs P235GH, SFS-EN 10216-2.
The material of pipes belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10216-2.
Käyrien, kartioiden, päätyjen ja T-putkien materiaa-li on seostamaton teräs P235GH, SFS-EN 10253-2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standar-din SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistusvaati-mukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an author-ized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
Putkenosien mukana on lisäksi toimitettava valmis-tajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
4 MITAT 4 DIMENSIONS
Putkiluokkaan E10C1B kuuluvien putkien ja putke-nosien mitat ja mittastandardit on esitetty taulu-koissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E10C1B are shown in Ta-bles 1, 2 and 3.
Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama lii-tospäissä ja osan keskellä. Seinämät voidaan tar-vittaessa viistää hitsauspäissä vastaamaan liitty-vää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
SFS-EN ISO 7089 Grade A S235JR tai vastaava / or equal
SFS-EN 10025-2 -
Tiiviste PN 10 Gasket PN 10
SFS-EN 1514-1, tyyppi IBC SFS-EN 1514-1, type IBC
2) -
-
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201. Ruuvin lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella. 3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole vaikutusta
mekaanisiin ominaisuuksiin. 4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin materiaalin
valmistajan antamiin materiaalitodistuksiin 5) Kierteellisten putkenosien suurin suositeltava nimelliskoko on DN 50. 1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4. See standard
PSK 4201. Starting material shall comply with requirements in SFS-EN 10269. 2) The gasket material and thickness are determined by the fluid and process conditions. 3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C but this has
no effect on mechanical properties. 4) The fittings or their packages must have markings, by which the fittings can be connected to related material certificates
given by the supplier. 5) The maximum recommended size for threaded pipe fittings is DN 50.
NEET JA LÄMPÖTILAT 5 THE ALLOWABLE OPERATING PRESSURES
AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 10 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen.
The pipes and fittings belonging to this pipe class have been designed to resist 10 bar overpressure in 20 °C temperature and the maximum allowable temperature is 400 °C. The vacuum resistance is according to standard PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa on esitetty kuvassa 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan kertomalla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 10) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 10).
Yli 400 °C:n lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4203 E10C1B 11 (16)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 The allowable pressures (bar) as a function of temperature Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpöti-laan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 10). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine.
Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN 10). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
1) Haaroituksen kulma on 90° ± 5°. Haaroituksen molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon. 1) The angle of the branch connection is 90° ± 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in.
PSK Standardisointi PSK 4203 E10C1B 13 (16)
OPASTAVIA TIETOJA INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille:
General calculation criteria for piping components of pipe class:
- mitoitus SFS-EN 13480-3 mukaan - ylipaine 1,0 MPa - lämpötila 20 °C - suunnittelujännitys f = 150 MPa - korroosiovara c0 = 1,0 mm hitsausliitoksen lujuuskerroin z = 1,0
- dimensioning in accordance with SFS-EN 13480-3 - overpressure 1,0 MPa - temperature 20 °C - design stress f = 150 MPa - corrosion allowance c0 = 1,0 mm - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmis-tustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
putket: pipes: - 12,5 % tai 0,4 mm, kun DN ≤ 200 - 20 %, kun DN > 200
- 12,5 % or 0,4 mm, when DN ≤ 200 - 20 % when DN > 200
käyrät, kartiot, T-putket ja päädyt: elbows, reducers, tee pieces and caps: - 12,5 %, kun DN ≤ 600 - 0,5 mm, kun DN > 600
- 12,5 %, when DN ≤ 600 - 0,5 mm, when DN > 600
Kartioiden laskenta on tehty epäkeskeisille kartioil-le. Kartiot on laskettu muovattuina DN 500:aan asti ja levykartioina DN 600:sta ylöspäin.
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and upwards from DN 600 as straight reducers.
PSK Standardisointi PSK 4203 E10C1B 14 (16)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4203 E10C1B 15 (16)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
Kuva 3 Istutusten viistäminen
Figure 3 Bevelling of branches
O.3 Nimikkeen muodostaminen O.3 Forming of designation
Examples of designations: - Pipe - 114,3 x 3,6 - SFS-EN 10216-2 -P235GH - TC
1 - Elbow 114,3 x 3,6 - SFS-EN 10253-2 - type A - 3D -
90° - P235GH - Reducer E1) 114,3 x 3,6 - 88,9 x 3,6 - SFS-EN
10253-2 - type A - P235GH - Tee 114,3 x 3,6 - 114,3 x 3,2 - SFS-EN 10253-2 -
type A - P235GH - Welding neck flange DN 100 - SFS-EN 1092-1 - PN
10 - type 11 - B1 - P250GH - Cap 114,3 x 3,6 - SFS-EN 10253-2 - type A -
P235GH - Gasket DN 100 - PN 10 - type IBC – 1,5 mm -SFS-
EN 1514-1 - graphite laminate2)
1) E = epäkeskeinen, K = keskeinen 1) E = eccentric, K = concentric 2) Tiivistemateriaalin valinta ja tiivisteen paksuus
määräytyvät virtaavan aineen ja prosessiolo-suhteiden mukaan.
2) The selection of the gasket material and thickness shall be determined by the fluid and process condi-tions
PSK Standardisointi PSK 4203 E10C1B 16 (16)
O.4 Putkiluokan tunnus O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhden-mukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokkamerkintää.
The letter E in the beginning of the identification of the pipe class shows that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältö poikkeaa tässä standardissa esitetystä.
A different identification shall be given to the pipe class, if the contents deviate from this standard.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting mate-rials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been re-placed by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- Nimelliskokojen DN600…700 komponenttien mittoja on korjattu vastaamaan viitestandardien mittoja
- The dimensions of components in nominal sizes DN600…700 have been revised to comply with refer-ence standards
- Putkiluokan suunnittelujännitys f kohdassa O.1 muutettu.
- The design stress f in section O.1 has been changed
- Kuva 1 ja taulukko 4 on muutettu vastaamaan uutta suunnittelujännityksen arvoa.
- Figure 1 and table 4 have been revised to match the new design stress
lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and
temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the
standard
1 SOVELTAMISALA
1 SCOPE
Tässä standardissa esitetään putkiluokkaan E10C1C kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 10 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C.
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E10C1C, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 10 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardin SFS-EN 13480 osissa 2 - 5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2 - 5.
2 VIITTAUKSET
2 REFERENCES
PSK 4201 Putkiluokat. Määrittely. 2021
PSK 4201 Pipe classes. Definition. 2021
SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018
SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2018
SFS-EN 1514-1:en Laipat ja yhteet. PN-mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei-metalliset tasotiivisteet. 1997
SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
SFS-EN 10028-2:2017 Painelaiteteräkset. Levytuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004
SFS-EN 10216-2:2014 + A1:2019: Saumattomat painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Kuumalujat seostamattomat ja seostetut teräsputket. 2014
SFS-EN 10216-2:2014 + A1:2019: Seamless steel tubes for pressure purposes. Technical delivery conditions. Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties. 2014
SFS-EN 10217-2:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Sähkövastushitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-2:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions- Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10217-5:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 5: Jauhekaarihitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-5:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions. Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset teräkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020:en Metallic industrial piping. Part 3: Design and calculation. 2017
PSK Standardisointi PSK 4204 E10C1C 3 (18) SFS-EN 13480-4:2017 Metalliset teollisuusputkistot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
SFS-EN ISO 898-1 Kiinnityselimien lujuusominaisuudet. Seostamattomat ja seos-teräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032:en Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032:en Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Normaalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT
3 MATERIALS
Tähän putkiluokkaan kuuluvien DN 15…300 putkien materiaali on seostamaton teräs P235GH, SFS-EN 10216-2.
The material of pipes DN 15…300 belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10216-2.
DN 350…500 putkien materiaali on seostamaton teräs P235GH, SFS-EN 10217-2.
The material of pipes DN 350…500 is non-alloy steel P235GH, SFS-EN 10217-2.
Putkien DN 600...1200 materiaali on P235GH, SFS-EN 10217-5.
The material of pipes DN 600...1200 is P235GH, SFS-EN 10217-5.
Käyrien, kartioiden, päätyjen ja T-putkien materiaali on seostamaton teräs P235GH, SFS-EN 10253-2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standardin SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistus-vaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an authorized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
PSK Standardisointi PSK 4204 E10C1C 4 (18) Putkenosien mukana on lisäksi toimitettava valmistajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
4 MITAT
4 DIMENSIONS
Putkiluokkaan E10C1C kuuluvien putkien ja putkenosien mitat ja mittastandardit on esitetty taulukoissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E10C1C are shown in Tables 1, 2 and 3.
Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama liitospäissä ja osan keskellä. Seinämät voidaan tarvittaessa viistää hitsauspäissä vastaamaan liittyvää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
Seinämänpaksuudet voivat poiketa standardissa SFS-EN 10253-2 esitetyistä mitoista.
Wall thicknesses may deviate from those specified in SFS-EN 10253-2.
PSK Standardisointi PSK 4204 E10C1C 5 (18) Taulukko 1 Putkien, käyrien, päätyjen, kartioiden ja T-putkien mitat (mm) Table 1 The dimensions of pipes, elbows, caps, reducers and tees (mm)
1200 1455 1380 32 M36 132 55 1341 1) Tiivisteen ulkohalkaisija 1) Outside diameter of the gasket
PSK Standardisointi PSK 4204 E10C1C 11 (18) Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, mutterien, aluslaattojen ja tiivisteiden mittastandardit ja materiaalit Table 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts, washers and gaskets
Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Nimike Designation
Standardi Standard
Todistus Certificate
Kauluslaippa PN 10 Welding neck flange PN 10
SFS-EN 1092-1, tyyppi 11-B1 SFS-EN 1092-1, type 11-B1
P250GH SFS-EN 10222-2 3.1
Umpilaippa PN 10 Blind flange
SFS-EN 1092-1, tyyppi 05 SFS-EN 1092-1, type 05
P265GH SFS-EN 10028-2 3.1
Sokeointilevy Spade
PSK 7820 P265GH SFS-EN 10028-2 3.1
Kierteelliset putkenosat 4) 5)
Threaded pipe fittings SFS-EN 10241 P235GH tai / or
P250GH SFS-EN 10273 SFS-EN 10222-2
3.1
Ruuvi 3) 4)
Bolt SFS-EN ISO 4014 25CrMo4
5.6 1) (T < 50 °C) SFS-EN 10269 SFS-EN ISO 898-1
3.1 2.2
Mutteri 3) 4)
Nut SFS-EN ISO 4032
25CrMo4 5 (T ≤ 50 °C)
SFS-EN 10269 SFS-EN ISO 898-2
3.1 2.2
Aluslaatta 3)
Washer SFS-EN ISO 7089 Grade A S235JR tai vastaava
/ or equal
SFS-EN 10025-2 -
Tiiviste PN 10 Gasket PN 10
SFS-EN 1514-1, tyyppi IBC SFS-EN 1514-1, type IBC
2) - -
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201. Ruuvin lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella.
3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole vaikutusta mekaanisiin ominaisuuksiin.
4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin materiaalin valmistajan antamiin materiaalitodistuksiin
5) Kierteellisten putkenosien suurin suositeltava nimelliskoko on DN 50. 1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4. See standard
PSK 4201. Starting material shall comply with requirements in SFS-EN 10269. 2) The gasket material and thickness are determined by the fluid and process conditions. 3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C but this has no
effect on mechanical properties. 4) The fittings or their packages must have markings, by which the fittings can be connected to related material certificates
given by the supplier. 5) The maximum recommended size for threaded pipe fittings is DN 50.
KÄYTTÖPAINEET JA LÄMPÖTILAT 5 THE ALLOWABLE OPERATING
PRESSURES AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 10 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen. alipaineen.
The pipes and fittings belonging to this pipe class have been designed to resist 10 bar overpressure in 20 °C temperature and the maximum allowable temperature is 400 °C. The vacuum resistance is according to standard PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa on esitetty kuvassa 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan kerto-malla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 10) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 10).
Yli 400 °C:n lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4204 E10C1C 13 (18)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 The allowable pressures (bar) as a function of temperature Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 10). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine.
Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN10). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
1) Haaroituksen kulma on 90° ± 5°. Haaroituksen molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon. 1) The angle of the branch connection is 90° ± 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in.
PSK Standardisointi PSK 4204 E10C1C 15 (18)
OPASTAVIA TIETOJA
INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille: General calculation criteria for piping components of pipe class:
- mitoitus SFS-EN 13480-3 mukaan - dimensioning in accordance with SFS-EN 13480-3 - ylipaine 1,0 MPa - overpressure 1,0 MPa - lämpötila 20 °C - temperature 20 °C - suunnittelujännitys f = 150 MPa - design stress f = 150 MPa - korroosiovara c0 = 1,0 mm - corrosion allowance c0 = 1,0 mm - hitsausliitoksen lujuuskerroin z = 1,0 - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmistustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
putket: pipes: - 12,5 % tai 0,4 mm, kun DN ≤ 200 - 12,5 % or 0,4 mm, when DN ≤ 200 - 20 %, kun 200 < DN ≤ 300 - 20 %, when 200 < DN ≤ 300 - 8 %, kun DN > 300
- 8 %, when DN > 300
käyrät, kartiot, T-putket ja päädyt: elbows, reducers, tee pieces and caps: - 12,5 %, kun DN ≤ 600 - 12,5 %, when DN ≤ 600 - 0,35 mm, kun DN > 600 ja T ≤ 10,0 mm - 0,35 mm, when DN > 600 and T ≤ 10,0 mm - 0,5 mm, kun DN > 600 ja T > 10,0 mm
- 0,5 mm, when DN > 600 and T > 10,0 mm
Kartioiden laskenta on tehty epäkeskeisille kartioille. Kartiot on laskettu muovattuina DN 500:aan asti ja levykartioina DN 600:sta ylöspäin.
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and upwards from DN 600 as straight reducers.
PSK Standardisointi PSK 4204 E10C1C 16 (18)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4204 E10C1C 17 (18)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
Kuva 3 Istutusten viistäminen
Figure 3 Bevelling of branches
O.3 Nimikkeen muodostaminen O.3 Forming of designation
Esimerkkejä nimikkeen muodostamisesta: Examples of designations:
- Gasket DN 100 - PN 10 - type IBC - 1,5 mm - SFS-EN 1514-1 - graphite laminate 2)
1) E = epäkeskeinen, K = keskeinen 1) E = eccentric, K = concentric 2) Tiivistemateriaalin valinta ja tiivisteen paksuus
määräytyvät virtaavan aineen ja prosessiolo-suhteiden mukaan.
2) The selection of the gasket material and thickness shall be determined by the fluid and process conditions
PSK Standardisointi PSK 4204 E10C1C 18 (18)
O.4 Putkiluokan tunnus O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokkamerkintää.
The letter E in the beginning of the identification of the pipe class shows that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältö poikkeaa tässä standardissa esitetystä.
A different identification shall be given to the pipe class, if the contents deviate from this standard.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting materials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been replaced by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- Nimelliskokojen DN600…1200 komponenttien mittoja on korjattu vastaamaan viitestandardien mittoja
- The dimensions of components in nominal sizes DN600…1200 have been revised to comply with reference standards
- Putkiluokan suunnittelujännitys f kohdassa O.1 muutettu.
- The design stress f in section O.1 has been changed
- Kuva 1 ja taulukko 4 on muutettu vastaamaan uutta suunnittelujännityksen arvoa.
- Figure 1 and table 4 have been revised to match the new design stress
Korvaa standardin PSK 4205:2017 Replaces the standard PSK 4205:2017 PUTKILUOKKA E16C1A PAINELAITEKÄYTTÖÖN. KUUMALUJA SEOSTAMATON TERÄS. HITSATTU TERÄSPUTKI Pipe class E16C1A for pressure purposes. Welded non-alloy steel pipe for elevated temperatures
Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail.
Sisällys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5 Putkiluokan sallitut käyttöpaineet ja lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and
temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the
standard
1 SOVELTAMISALA 1 SCOPE
Tässä standardissa esitetään putkiluokkaan E16C1A kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 16 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C.
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E16C1A, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 16 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5.
2 VIITTAUKSET 2 REFERENCES
PSK 4201 Putkiluokat. Määrittely. 2021
PSK 4201 Pipe classes. Definition. 2021
SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018
SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2018
SFS-EN 1514-1:en Laipat ja yhteet. PN-mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei-metalliset tasotiivisteet. 1997
SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
SFS-EN 10028-2:2017 Painelaiteteräkset. Levy-tuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004.
SFS-EN 10217-2:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Sähkövastushitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-2:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions- Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10217-5:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 5: Jauhekaarihitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-5:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions. Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset teräkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020:en Metallic industrial piping. Part 3: Design and calculation. 2017
SFS-EN 13480-4:2017 Metalliset teollisuusputkistot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
PSK Standardisointi PSK 4205 E16C1A 3 (17) SFS-EN ISO 898-1 Kiinnityselimien lujuusominaisuudet. Seostamattomat ja seosteräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032:en Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032:en Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Normaalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT 3 MATERIALS
Tähän putkiluokkaan kuuluvien DN 15…500 putkien materiaali on seostamaton teräs P235GH, SFS-EN 10217-2.
The material of pipes DN 15…500 belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10217-2.
The material of pipes DN 600…1200 is non-alloy steel P235GH, SFS-EN 10217-5.
Käyrien, kartioiden, päätyjen ja T-putkien materiaali on seostamaton teräs P235GH, SFS-EN 10253-2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standardin SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistusvaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an authorized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
Putkenosien mukana on lisäksi toimitettava valmistajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
4 MITAT 4 DIMENSIONS
Putkiluokkaan E16C1A kuuluvien putkien ja putkenosien mitat ja mittastandardit on esitetty taulukoissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E16C1A are shown in Tables 1, 2 and 3.
PSK Standardisointi PSK 4205 E16C1A 4 (17) Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama liitospäissä ja osan keskellä. Seinämät voidaan tarvittaessa viistää hitsauspäissä vastaamaan liittyvää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
1) The dimensions apply also to eccentric reducers.
PSK Standardisointi PSK 4205 E16C1A 9 (17) Taulukko 2 Laippojen mitat Table 2 The dimensions of flanges
PN 16
SFS-EN 1092-1
Tyyppi 11 Type 11
DN D K
Ruuvit Bolts H2 C2
Sokeointilevy Spade
Määrä Quantity
Koko Size d 1) s
15 95 65 4 M12 38 16 51
Kts./See PSK 7820
20 105 75 4 M12 40 18 61
25 115 85 4 M12 40 18 71
32 140 100 4 M16 42 18 82
40 150 110 4 M16 45 18 92
50 165 125 4 M16 45 18 107
65 185 145 8 M16 45 18 127
80 200 160 8 M16 50 20 142
100 220 180 8 M16 52 20 162
125 250 210 8 M16 55 22 192
150 285 240 8 M20 55 22 218
200 340 295 12 M20 62 24 273
250 405 355 12 M24 70 26 329
300 460 410 12 M24 78 28 384
350 520 470 16 M24 82 30 444
400 580 525 16 M27 85 32 495
450 640 585 20 M27 83 34 555
500 715 650 20 M30 84 36 617
600 840 770 20 M33 88 40 734
700 910 840 24 M33 104 40 804
800 1025 950 24 M36 108 41 911
900 1125 1050 28 M36 118 48 1011
1000 1255 1170 28 M39 137 59 1128
1200 1485 1390 32 M45 160 78 1342 1)
Tiivisteen ulkohalkaisija
1) Outside diameter of the gasket
PSK Standardisointi PSK 4205 E16C1A 10 (17)
Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, mutterien, aluslaattojen ja tiivisteiden mittastandardit ja materiaalit Table 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts, washers and gaskets Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Nimike Designation
Standardi Standard
Todistus Certificate
Kauluslaippa PN 16 Welding neck flange PN 16
SFS-EN 1092–1, tyyppi 11-B1 SFS-EN 1092–1, type 11-B1
P250GH SFS-EN 10222-2 3.1
Umpilaippa PN 16 Blind flange PN 16
SFS-EN 1092–1, tyyppi 05 SFS-EN 1092–1, type 05
P265GH SFS-EN 10028-2 3.1
Sokeointilevy Spade
PSK 7820 P265GH SFS-EN 10028-2 3.1
Kierteelliset putkenosat 4)
5)
Threaded pipe fittings
SFS-EN 10241 P235GH tai / or P250GH
SFS-EN 10273 SFS-EN 10222-2
3.1
Ruuvi 3) 4)
Bolt SFS-EN ISO 4014 25CrMo4
5.6 1) (T < 50 °C) SFS-EN 10269 SFS-EN ISO 898-1
3.1 2.2
Mutteri 3) 4)
Nut SFS-EN ISO 4032 25CrMo4
5 (T ≤ 50 °C) SFS-EN 10269 SFS-EN ISO 898-2
3.1 2.2
Aluslaatta 3)
Washer SFS-EN ISO 7089 Grade A S235JR tai vastaava
/ or equal
SFS-EN 10025-2 -
Tiiviste PN 16 Gasket PN 16
SFS-EN 1514-1, tyyppi IBC SFS-EN 1514-1, type IBC
2) - -
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201. Ruuvin lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella.
3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole vaikutusta mekaanisiin ominaisuuksiin.
4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin materiaalin valmistajan antamiin materiaalitodistuksiin
5) Kierteellisten putkenosien suurin suositeltava nimelliskoko on DN 50. 1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4. See standard
PSK 4201. Starting material shall comply with requirements in SFS-EN 10269. 2) The gasket material and thickness are determined by fluid and process conditions. 3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C but this has
no effect on mechanical properties. 4) The fittings or their packages must have markings, by which the fittings can be connected to related material certificates
given by the supplier. 5) The maximum recommended size for threaded pipe fittings is DN 50.
5 THE ALLOWABLE OPERATING PRESSURES AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 16 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen.
The pipes and fittings belonging to this pipe class have been designed to resist 16 bar overpressure in 20 °C temperature, and the maximum allowable temperature is 400 °C. The vacuum resistance is according to standard PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa on esitetty kuvassa 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan ker-tomalla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 16) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 16).
Yli 400 °C lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4205 E16C1A 12 (17)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 Allowable pressures (bar) as a function of temperature
Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 16). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine.
Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN 16). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
1219 12,5 24,0 23,4 22,8 22,2 21,7 20,8 19,8 19,1 17,8 16,7 15,7 14,1 12,8 12,0 11,3 10,8 10,0 9,4 8,3 7,8 7,4 7,7 7,1 7,3 1) Haaroituksen kulma on 90° ± 5°. Haaroituksen molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon. 1) The angle of the branch connection is 90° ± 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in.
PSK Standardisointi PSK 4205 E16C1A 14 (17)
OPASTAVIA TIETOJA INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille:
General calculation criteria for piping components of pipe class:
- mitoitus SFS-EN 13480-3 mukaan - dimensioning in accordance with SFS-EN 13480-3
- ylipaine 1,6 MPa - overpressure 1,6 MPa - lämpötila 20 °C - temperature 20 °C - suunnittelujännitys f = 150 MPa - design stress f = 150 MPa - korroosiovara c0 = 1,0 mm - corrosion allowance c0 = 1,0 mm - hitsausliitoksen lujuuskerroin z = 1,0 - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmistustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
putket: pipes:
- putket - pipes and branch connections
- 10 % tai 0,3 mm, kun T ≤ 5,0 mm - 10 % or 0,3 mm, when T ≤ 5,0 mm - 8 %, kun T > 5,0 mm - 8 %, when T > 5,0 mm
käyrät, kartiot, T-putket ja päädyt: elbows, reducers, tee pieces and caps:
- käyrät, kartiot, T-putket ja päädyt - elbows, reducers, tee pieces and caps
- 12,5 %, kun DN ≤ 600 - 12,5 %, when DN ≤ 600 - 0,35 mm, kun DN > 600 ja T ≤ 10,0 mm - 0,35 mm, when DN > 600 and T ≤ 10,0 mm - 0,5 mm, kun DN > 600 ja T > 10,0 mm
- 0,5 mm, when DN > 600 and T > 10,0 mm
Kartioiden laskenta on tehty epäkeskeisille kartioille. Kartiot on laskettu muovattuina DN 500:aan asti ja levykartioina DN 600:sta ylöspäin.
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and upwards from DN 600 as straight reducers.
PSK Standardisointi PSK 4205 E16C1A 15 (17)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4205 E16C1A 16 (17)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
Kuva 3 Istutusten viistäminen
Figure 3 Bevelling of branches
O.3 Nimikkeen muodostaminen O.3 Forming of designation
- Gasket DN 100 - PN 16 - type IBC - 1,5 mm - SFS-EN 1514-1 - graphite laminate 2)
1) E = epäkeskeinen, K = keskeinen 2) Tiivistemateriaalin valinta ja tiivisteen paksuus määräytyvät virtaavan aineen ja prosessiolo- suhteiden mukaan.
1) E= Eccentric, K = concentric 2) The selection of the gasket material and thickness
shall be determined by the fluid and process conditions
PSK Standardisointi PSK 4205 E16C1A 17 (17)
O.4 Putkiluokan tunnus O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokan merkintää.
The letter E in the beginning of the identification of the pipe class shows, that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältö poikkeaa tässä standardissa esitetystä
A different identification code shall be given to the pipe class, if the contents deviate from this standard.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting materials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been replaced by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- Nimelliskokojen DN600…1200 komponenttien mittoja on korjattu vastaamaan viitestandardien mittoja
- The dimensions of components in nominal sizes DN600…1200 have been revised to comply with reference standards
- Putkiluokan suunnittelujännitys f kohdassa O.1 muutettu.
- The design stress f in section O.1 has been changed
- Kuva 1 ja taulukko 4 on muutettu vastaamaan uutta suunnittelujännityksen arvoa.
- Figure 1 and table 4 have been revised to match the new design stress
lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and
temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the
standard
1 SOVELTAMISALA 1 SCOPE
Tässä standardissa esitetään putkiluokkaan E16C1B kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 16 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C.
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E16C1B, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 16 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5.
SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018
SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2018
SFS-EN 10253-2 Päittäishitsattavat putkenosat. Osa 2: Toimituseräkohtaisesti tarkastettavat seostamattomat teräkset ja ferriittiset seosteräkset. 2008
SFS-EN 10253-2:en Butt-welding pipe fittings. Part 2: Non alloy and ferritic alloy steels with specific inspection requirements. 2008
SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
SFS-EN 10028-2:2017 Painelaiteteräkset. Levy-tuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004
SFS-EN 10216-2:2014 + A1:2019 Saumattomat painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Kuumalujat seostamattomat ja seostetut teräsputket. 2014
SFS-EN 10216-2:2014 + A1:2019:en Seamless steel tubes for pressure purposes. Technical delivery conditions. Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties. 2014
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset teräkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020:en Metallic industrial piping. Part 3: Design and calculation. 2017
SFS-EN 13480-4:2017 Metalliset teollisuusputkistot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
PSK Standardisointi PSK 4206 E16C1B 3 (16) SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
SFS-EN ISO 898-1 Kiinnityselimien lujuusominaisuudet. Seostamattomat ja seos-teräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032:en Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032:en Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Normaalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT 3 MATERIALS
Tähän putkiluokkaan kuuluvien putkien materiaali on seostamaton teräs P235GH, SFS-EN 10216-2.
The material of pipes belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10216-2.
Käyrien, kartioiden, päätyjen ja T-putkien materiaali on seostamaton teräs P235GH, SFS-EN 10253-2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standardin SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistus-vaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an authorized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
Putkenosien mukana on lisäksi toimitettava valmistajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
4 MITAT 4 DIMENSIONS
Putkiluokkaan E16C1B kuuluvien putkien ja putkenosien mitat ja mittastandardit on esitetty taulukoissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E16C1B are shown in Tables 1, 2 and 3.
PSK Standardisointi PSK 4206 E16C1B 4 (16) Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama liitospäissä ja osan keskellä. Seinämät voidaan tarvittaessa viistää hitsauspäissä vastaamaan liittyvää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
1) Mitat koskevat myös epäkeskeisiä kartioita. 1) The dimensions apply also to eccentric reducers.
PSK Standardisointi PSK 4206 E16C1B 8 (16) Taulukko 2 Laippojen mitat Table 2 The dimensions of flanges
PN 16
SFS-EN 1092-1
Tyyppi 11 Type 11
DN D K
Ruuvit Bolts H2 C2
Sokeointilevy
Spade
Määrä Quantity
Koko Size d 1) s
15 95 65 4 M12 38 16 51
Kts./See PSK 7820
20 105 75 4 M12 40 18 61
25 115 85 4 M12 40 18 71
32 140 100 4 M16 42 18 82
40 150 110 4 M16 45 18 92
50 165 125 4 M16 45 18 107
65 185 145 8 M16 45 18 127
80 200 160 8 M16 50 20 142
100 220 180 8 M16 52 20 162
125 250 210 8 M16 55 22 192
150 285 240 8 M20 55 22 218
200 340 295 12 M20 62 24 273
250 405 355 12 M24 70 26 329
300 460 410 12 M24 78 28 384
350 520 470 16 M24 82 30 444
400 580 525 16 M27 85 32 495
450 640 585 20 M27 83 34 555
500 715 650 20 M30 84 36 617
600 840 770 20 M33 88 40 734
700 910 840 24 M33 104 40 804 1) Tiivisteen ulkohalkaisija 1) Outside diameter of the gasket
PSK Standardisointi PSK 4206 E16C1B 9 (16) Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, mutterien, aluslaattojen ja tiivisteiden mittastandardit ja materiaalit Table 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts, washers and gaskets
Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Nimike Designation
Standardi Standard
Todistus Certificate
Kauluslaippa PN 16 Welding neck flange PN 16
SFS-EN 1092–1, tyyppi 11-B1 SFS-EN 1092–1, type 11-B1
P250GH SFS-EN 10222-2 3.1
Umpilaippa PN 16 Bling flange PN 16
SFS-EN 1092–1, tyyppi 05 SFS-EN 1092–1, type 05
P265GH SFS-EN 10028-2 3.1
Sokeointilevy Spade
PSK 7820 P265GH SFS-EN 10028-2 3.1
Kierteelliset putkenosat 4) 5)
Threaded pipe fittings SFS-EN 10241 P235GH tai / or
P250GH SFS-EN 10273 SFS-EN 10222-2
3.1
Ruuvi 3) 4)
Bolt SFS-EN ISO 4014 25CrMo4
5.6 1) (T ≤ 50 °C) SFS-EN 10269 SFS-EN ISO 898-1
3.1 2.2
Mutteri 3) 4)
Nut SFS-EN ISO 4032
25CrMo4 5 (T ≤ 50 °C)
SFS-EN 10269 SFS-EN ISO 898-2
3.1 2.2
Aluslaatta 3)
Washer
SFS-EN ISO 7089 Grade A S235JR tai vastaava / or equal
SFS-EN 10025-2 -
Tiiviste PN 16 Gasket PN 16
EN 1514–1, tyyppi IBC EN 1514–1, type IBC
2) - -
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201.
Ruuvin lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella.
3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole
vaikutusta mekaanisiin ominaisuuksiin.
4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin
materiaalin valmistajan antamiin materiaalitodistuksiin
5) Kierteellisten putkiluokkien suurin suositeltava nimelliskoko on DN 50.
1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4.
See standard PSK 4201. Starting material shall comply with requirements in SFS-EN 10269.
2) The gasket material and thickness are determined by fluid and process conditions.
3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C
but this has no effect on mechanical properties.
4) The fittings or their packages must have markings, by which the fittings can be connected to related material
certificates given by the supplier.
5) The maximum recommended size for threaded pipe fittings is DN 50.
PSK Standardisointi PSK 4206 E16C1B 10 (16)
5 PUTKILUOKAN SALLITUT KÄYTTÖPAINEET JA LÄMPÖTILAT
5 THE ALLOWABLE OPERATING PRESSURES AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 16 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen.
The pipes and fittings belonging to this pipe class have been designed to resist 16 bar overpressure in 20 °C temperature and the maximum allowable temperature is 400 °C. The vacuum resistance is according to PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa on esitetty kuvassa 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan kertomalla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 16) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 16).
Yli 400°C:n lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4206 E16C1B 11 (16)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 Allowable pressures (bar) as a function of temperature
Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 16). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine.
Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN 16). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
1) Haaroituksen kulma on 90° + 5°. T-haaran molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon. 1) The angle of the branch connection is 90° + 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in.
PSK Standardisointi PSK 4206 E16C1B 13 (16)
OPASTAVIA TIETOJA INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille:
General calculation criteria for piping components of pipe class:
- mitoitus SFS-EN 13480-3 mukaan - ylipaine 1,6 MPa - lämpötila 20 °C - suunnittelujännitys f = 150 MPa - korroosiovara c0 = 1,0 mm - hitsausliitoksen lujuuskerroin z = 1,0
- dimensioning in accordance with SFS-EN 13480-3
- overpressure 1,6 MPa - temperature 20 °C - design stress f = 150 MPa - corrosion allowance c0 = 1,0 mm - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmistustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
putket: pipes:
- 12,5 % tai 0,4 mm, kun DN ≤ 200 - 20 %, kun DN > 200
- 12,5 % or 0,4 mm, when DN ≤ 200 - 20 %, when DN > 200
käyrät, kartiot, T-putket ja päädyt: elbows, reducers, tee pieces and caps:
- 12,5 %, kun DN ≤ 600 - 0,5 mm, kun DN > 600
- 12,5 %, when DN ≤ 600 - 0,5 mm, when DN > 600
Kartioiden laskenta on tehty epäkeskeisille kartioille. Kartiot on laskettu muovattuina DN 500:aan asti ja levykartioina DN 600:sta ylöspäin.
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and upwards from DN 600 as straight reducers.
PSK Standardisointi PSK 4206 E16C1B 14 (16)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4206 E16C1B 15 (16)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
Kuva 3 Istutusten viistäminen
Figure 3 Bevelling of branches
O.3 Nimikkeen muodostaminen O.3 Forming of designation
- Cap 114,3 x 3,6 - SFS-EN 10253-2 - type A - P235GH
- Gasket DN 100 - PN 16 - type IBC – 1,5 mm - SFS-EN 1514-1 - graphite laminate 2)
1) E = epäkeskeinen, K = keskeinen 2) Tiivistemateriaalin valinta ja tiivisteen paksuus määräytyvät virtaavan aineen ja prosessiolo- suhteiden mukaan.
1) E= Eccentric, K = concentric 2) The selection of the gasket material and
thickness shall be determined by the fluid and process conditions
PSK Standardisointi PSK 4206 E16C1B 16 (16)
O.4 Putkiluokan tunnus O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokkamerkintää.
The letter E in the beginning of the identification code of the pipe class shows that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältö poikkeaa tässä standardissa esitetystä
A different identification code shall be given to the pipe class, if the contents deviate from this standard.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting materials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been replaced by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- Nimelliskokojen DN600…700 komponenttien mittoja on korjattu vastaamaan viitestandardien mittoja
- The dimensions of components in nominal sizes DN600…700 have been revised to comply with reference standards
- Putkiluokan suunnittelujännitys f kohdassa O.1 muutettu.
- The design stress f in section O.1 has been changed
- Kuva 1 ja taulukko 4 on muutettu vastaamaan uutta suunnittelujännityksen arvoa.
- Figure 1 and table 4 have been revised to match the new design stress
Korvaa standardin PSK 4207:2017 Replaces the standard PSK 4207:2017 PUTKILUOKKA E16C1C PAINELAITEKÄYTTÖÖN. KUUMALUJA SEOSTAMATON TERÄS. SAUMATON/HITSATTU TERÄSPUTKI Pipe class E16C1C for pressure purposes. Seamless/welded non-alloy steel pipe for elevated temperatures
Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail.
Sisällys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5 Putkiluokan sallitut käyttöpaineet ja lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and
temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the
standard
1 SOVELTAMISALA 1 SCOPE
Tässä standardissa esitetään putkiluokkaan E16C1C kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 16 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C.
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E16C1C, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 16 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5.
2 VIITTAUKSET
2 REFERENCES
PSK 4201 Putkiluokat. Määrittely. 2021
PSK 4201 Pipe classes. Definition. 2021
SFS-EN 1092-1 + A1 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2013
SFS-EN 1092-1 +A1 Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2013
SFS-EN 1514-1:en Laipat ja yhteet. PN-mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei-metalliset tasotiivisteet. 1997
SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
SFS-EN 10028-2:2017 Painelaiteteräkset. Levytuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004
SFS-EN 10216-2:2014 + A1:2019 Saumattomat painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Kuumalujat seostamattomat ja seostetut teräsputket. 2014
SFS-EN 10216-2:2014 + A1:2019:en Seamless steel tubes for pressure purposes. Technical delivery conditions. Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties. 2014
SFS-EN 10217-2:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Sähkövastushitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-2:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions- Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10217-5:2019 Hitsatut painelaiteteräsputket. Tekniset toimitusehdot. Osa 5: Jauhekaarihitsatut kuumalujat seostamattomat ja seostetut teräsputket. 2019
SFS-EN 10217-5:2019:en Welded steel tubes for pressure purposes. Technical delivery conditions. Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties. 2019
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset teräkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
PSK Standardisointi PSK 4207 E16C1C 3 (19) SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020:en Metallic industrial piping. Part 3: Design and calculation. 2017
SFS-EN 13480-4:2017 Metalliset teollisuusputkistot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
SFS-EN ISO 898-1 Kiinnityselimien lujuusominaisuudet. Seostamattomat ja seos-teräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032:en Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032:en Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Normaalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT
3 MATERIALS
Tähän putkiluokkaan kuuluvien DN 15 ... DN 300 putkien materiaali on seostamaton teräs P235GH, SFS-EN 10216-2.
The material of pipes DN 15 ... DN 300 belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10216-2.
DN 350…500 putkien materiaali on seostamaton teräs P235GH, SFS-EN 10217-2.
The material of pipes DN 350…500 is non-alloy steel P235GH, SFS-EN 10217-2.
Putkien DN 600...1200 materiaali on P235GH, SFS-EN 10217-5.
The material of pipes DN 600...1200 is P235GH, SFS-EN 10217-5.
Käyrien, kartioiden, päätyjen ja T-putkien materiaali on seostamaton teräs P235GH, SFS-EN 10253–2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
PSK Standardisointi PSK 4207 E16C1C 4 (19)
Putkille, putkenosille ja laipoille vaaditaan standardin SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistus-vaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an authorized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
Putkenosien mukana on lisäksi toimitettava valmistajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer’s certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
4 MITAT
4 DIMENSIONS
Putkiluokkaan E16C1C kuuluvien putkien ja putkenosien mitat ja mittastandardit on esitetty taulukoissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E16C1C are shown in Tables 1, 2 and 3.
Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama liitospäissä ja osan keskellä. Seinämät voidaan tarvittaessa viistää hitsauspäissä vastaamaan liittyvää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
1) The dimensions apply also to eccentric reducers.
PSK Standardisointi PSK 4207 E16C1C 11 (19) Taulukko 2 Laippojen mitat Table 2 The dimensions of flanges
PN 16
SFS-EN 1092-1
Tyyppi 11 Type 11
DN D K
Ruuvit Bolts
H2 C2
Sokeointilevy Spade
Määrä Quantity
Koko Size
d 1) s
15 95 65 4 M12 38 16 51
Kts./See PSK 7820
20 105 75 4 M12 40 18 61
25 115 85 4 M12 40 18 71
32 140 100 4 M16 42 18 82
40 150 110 4 M16 45 18 92
50 165 125 4 M16 45 18 107
65 185 145 8 M16 45 18 127
80 200 160 8 M16 50 20 142
100 220 180 8 M16 52 20 162
125 250 210 8 M16 55 22 192
150 285 240 8 M20 55 22 218
200 340 295 12 M20 62 24 273
250 405 355 12 M24 70 26 329
300 460 410 12 M24 78 28 384
350 520 470 16 M24 82 30 444
400 580 525 16 M27 85 32 495
450 640 585 20 M27 83 34 555
500 715 650 20 M30 84 36 617
600 840 770 20 M33 88 40 734
700 910 840 24 M33 104 40 804
800 1025 950 24 M36 108 41 911
900 1125 1050 28 M36 118 48 1011
1000 1255 1170 28 M39 137 59 1128
1200 1485 1390 32 M45 160 78 1342 1)
Tiivisteen ulkohalkaisija 1)
Outside diameter of the gasket
PSK Standardisointi PSK 4207 E16C1C 12 (19)
Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, mutterien, aluslaattojen ja tiivisteiden mittastandardit ja materiaalit Table 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts, washers and gaskets Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Nimike Designation
Standardi Standard
Todistus Certificate
Kauluslaippa PN 16 Welding neck flange PN 16
SFS-EN 1092–1, tyyppi 11-B1 SFS-EN 1092–1, type 11-B1
P250GH SFS-EN 10222-2 3.1
Umpilaippa PN 16 Blind flange PN 16
SFS-EN 1092–1, tyyppi 05 SFS-EN 1092–1, type 05
P265GH SFS-EN 10028-2 3.1
Sokeointilevy Spade
PSK 7820 P265GH SFS-EN 10028-2 3.1
Kierteelliset putkenosat 4) 5)
Threaded pipe fittings SFS-EN 10241 P235GH tai / or
P250GH SFS-EN 10273 SFS-EN 10222-2
3.1
Ruuvi 3) 4)
Bolt SFS-EN ISO 4014 25CrMo4
5.6 1) (T < 50 °C) SFS-EN 10269 SFS-EN ISO 898-1
3.1 2.2
Mutteri 3) 4)
Nut SFS-EN ISO 4032 25CrMo4
5 (T ≤ 50 °C) SFS-EN 10269 SFS-EN ISO 898-2
3.1 2.2
Aluslaatta 3)
Washer SFS-EN ISO 7089 Grade A S235JR tai
vastaava / equal
SFS-EN 10025-2 -
Tiiviste PN 16 Gasket PN 16
SFS-EN 1514-1, tyyppi IBC SFS-EN 1514-1, type IBC
2) - -
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201. Ruuvin lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella.
3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole vaikutusta mekaanisiin ominaisuuksiin.
4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin materiaalin valmistajan antamiin materiaalitodistuksiin
5) Kierteellisten putkenosien suurin suositeltava nimelliskoko on DN 50. 1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4. See standard
PSK 4201. Starting material shall comply with requirements in SFS-EN 10269. 2) The gasket material and thickness are determined by the fluid and process conditions. 3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C but this has
no effect on mechanical properties. 4) The fittings or their packages must have markings, by which the fittings can be connected to related material certificates
given by the supplier. 5) The maximum recommended size for threaded pipe fittings is DN 50.
5 THE ALLOWABLE OPERATING PRESSURES AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 16 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen.
The pipes and fittings belonging to this pipe class have been designed to resist 16 bar overpressure in 20 °C temperature, and the maximum allowable temperature is 400 °C. The vacuum resistance is according to PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa on esitetty kuvassa 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan kertomalla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 16) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 16).
Yli 400 °C lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4207 E16C1C 14 (19)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 Allowable pressures (bar) as a function of temperature
Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 16). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine.
Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN 16). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
Taulukko 4 Istutetun haaroituksen (90°) sallitut käyttöpaineet 20 °C:ssa, bar Table 4 Allowable operating pressures for branch connection at 20 °C, bar
1) Haaroituksen kulma on 90° ± 5°. T-haaran molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon. 1) The angle of the branch connection is 90° ± 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in.
PSK Standardisointi PSK 4207 E16C1C 16 (19)
OPASTAVIA TIETOJA INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille:
General calculation criteria for piping components of pipe class
- mitoitus SFS-EN 13480-3 mukaan - dimensioning in accordance with SFS-EN 13480-3
- ylipaine 1,6 MPa - overpressure 1,6 MPa - lämpötila 20 °C - temperature 20 °C - suunnittelujännitys f = 150 MPa - design stress f = 150 MPa - korroosiovara c0 = 1,0 mm - corrosion allowance c0 = 1,0 mm - hitsausliitoksen lujuuskerroin z = 1,0 - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmistustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
putket: pipes:
- 12,5 % tai 0,4 mm, kun DN ≤ 200 - 12,5 % or 0,4 mm, when DN ≤ 200 - 20 %, kun 200 < DN ≤ 300 - 20 %, when 200 < DN ≤ 300 - 8 %, kun DN > 300
- 8 %, when DN > 300
käyrät, kartiot, T-putket ja päädyt: elbows, reducers, tee pieces and caps:
- 12,5 %, kun DN < 600 - 12,5 %, when DN < 600 - 0,35 mm, kun DN > 600 ja T < 10,0 mm - 0,35 mm, when DN > 600 and T < 10,0 mm - 0,5 mm, kun DN > 600 ja T > 10,0 mm
- 0,5 mm, when DN > 600 and T > 10,0 mm
Kartioiden laskenta on tehty epäkeskeisille kartioille. Kartiot on laskettu muovattuina DN 500:aan asti ja levykartioina DN 600:sta ylöspäin.
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and upwards from DN 600 as straight reducers.
PSK Standardisointi PSK 4207 E16C1C 17 (19)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4207 E16C1C 18 (19)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
Kuva 3 Istutusten viistäminen
Figure 3 Bevelling of branches
O.3 Nimikkeen muodostaminen O.3 Forming of designation
- Gasket DN 100 - PN 16 - type IBC – 1,5 mm - SFS-EN 1514-1 - graphite laminate 2)
1) E = epäkeskeinen, K = keskeinen 1) E = eccentric, K = concentric 2) Tiivistemateriaalin valinta ja tiivisteen paksuus
määräytyvät virtaavan aineen ja prosessiolo-suhteiden mukaan.
2) The selection of the gasket material and thickness shall be determined by the fluid and process conditions.
PSK Standardisointi PSK 4207 E16C1C 19 (19) O.4 Putkiluokan tunnus
O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokkamerkintää.
The letter E in the beginning of the identification code of the pipe class shows that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting materials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been replaced by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- Nimelliskokojen DN600…1200 komponenttien mittoja on korjattu vastaamaan viitestandardien mittoja
- The dimensions of components in nominal sizes DN600…1200 have been revised to comply with reference standards
- Putkiluokan suunnittelujännitys f kohdassa O.1 muutettu.
- The design stress f in section O.1 has been changed
- Kuva 1 ja taulukko 4 on muutettu vastaamaan uutta suunnittelujännityksen arvoa.
- Figure 1 and table 4 have been revised to match the new design stress
PUTKILUOKKA E25C1B PAINELAITEKÄYTTÖÖN. KUUMALUJA SEOSTAMATON TERÄS. SAUMATON TERÄSPUTKI Pipe class E25C1B for pressure purposes. Seamless non-alloy steel pipe for elevated temperatures
Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail.
Sisällys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5 Putkiluokan sallitut käyttöpaineet ja lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and
temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the
standard
1 SOVELTAMISALA 1 SCOPE
Tässä standardissa esitetään putkiluokkaan E25C1B kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 25 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C.
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E25C1B, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 25 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5.
2 VIITTAUKSET
2 REFERENCES
PSK 4201 Putkiluokat. Määrittely. 2021
PSK 4201 Pipe classes. Definition. 2021
SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018
SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2018
SFS-EN 1514-1:en Laipat ja yhteet. PN-mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei-metalliset tasotiivisteet. 1997
SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
SFS-EN 10028-2:2017 Painelaiteteräkset. Levy-tuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004
SFS-EN 10216-2:2014 + A1:2019 Saumattomat painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Kuumalujat seostamattomat ja seostetut teräsputket. 2014
SFS-EN 10216-2:2014 + A1:2019:en Seamless steel tubes for pressure purposes. Technical delivery conditions. Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties. 2014
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset teräkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020: Metallic industrial piping. Part 3: Design and calculation. 2017
SFS-EN 13480-4:2017 Metalliset teollisuusputkistot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
SFS-EN ISO 898-1 Kiinnityselimien lujuusominaisuudet. Seostamattomat ja seos-teräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
PSK Standardisointi PSK 4208 E25C1B 3 (16)
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032:en Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032:en Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Normaalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT 3 MATERIALS
Tähän putkiluokkaan kuuluvien putkien materiaali on seostamaton teräs P235GH, SFS-EN 10216-2.
The material of pipes belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10216-2.
Käyrien, kartioiden, päätyjen ja T-putkien materiaali on seostamaton teräs P235GH, SFS-EN 10253–2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standardin SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistus-vaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an authorized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
Putkenosien mukana on lisäksi toimitettava valmistajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
4 MITAT 4 DIMENSIONS
Putkiluokkaan E25C1B kuuluvien putkien ja putkenosien mitat ja mittastandardit on esitetty taulukoissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E25C1B are shown in Tables 1, 2 and 3.
Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama liitospäissä ja osan keskellä. Seinämät voidaan tarvittaessa viistää hitsauspäissä vastaamaan liittyvää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
1) Mitat koskevat myös epäkeskeisiä kartioita. 1) The dimensions apply also to eccentric reducers.
PSK Standardisointi PSK 4208 E25C1B 8 (16)
Taulukko 2 Laippojen mitat Table 2 The dimensions of flanges
PN 25
SFS-EN 1092-1
Tyyppi 11 Type 11
DN D K
Ruuvit Bolts H2 C2
Sokeointilevy
Spade Määrä
Quantity Koko Size d 1) s
15 95 65 4 M12 38 16 51
Kts./See PSK 7820
20 105 75 4 M12 40 18 61
25 115 85 4 M12 40 18 71
32 140 100 4 M16 42 18 82
40 150 110 4 M16 45 18 92
50 165 125 4 M16 48 20 107
65 185 145 8 M16 52 22 127
80 200 160 8 M16 58 24 142
100 235 190 8 M20 65 24 168
125 270 220 8 M24 68 26 194
150 300 250 8 M24 75 28 224
200 360 310 12 M24 80 30 284
250 425 370 12 M27 88 32 340
300 485 430 16 M27 92 34 400
350 555 490 16 M30 100 38 457
400 620 550 16 M33 110 40 514
450 670 600 20 M33 110 46 564
500 730 660 20 M33 125 48 624
600 845 770 20 M36 125 48 731
700 960 875 24 M39 129 50 833 1) Tiivisteen ulkohalkaisija 1) Outside diameter of the gasket
PSK Standardisointi PSK 4208 E25C1B 9 (16)
Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, mutterien, aluslaattojen ja tiivisteiden mittastandardit ja materiaalit Table 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts, washers and gaskets
Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Nimike Designation
Standardi Standard
Todistus Certificate
Kauluslaippa PN 25 Welding neck flange PN 25
SFS-EN 1092–1, tyyppi 11-B1 SFS-EN 1092–1, type 11-B1
P250GH SFS-EN 10222-2 3.1
Umpilaippa PN 25 Blind flange PN 25
SFS-EN 1092–1, tyyppi 05 SFS-EN 1092–1, type 05
P265GH SFS-EN 10028-2 3.1
Sokeointilevy Spade
PSK 7820 P265GH SFS-EN 10028-2 3.1
Kierteelliset putkenosat 4) 5)
Threaded pipe fittings SFS-EN 10241 P235GH tai / or
P250GH SFS-EN 10273 SFS-EN 10222-2
3.1
Ruuvi 3) 4)
Bolt SFS-EN ISO 4014 25CrMo4
5.6 1) (T ≤ 50 °C) SFS-EN 10269 SFS-EN ISO 898-1
3.1 2.2
Mutteri 3) 4) Nut
SFS-EN ISO 4032 25CrMo4 5 (T ≤ 50 °C)
SFS-EN 10269 SFS-EN ISO 898-2
3.1 2.2
Aluslaatta 3)
Washer SFS-EN ISO 7089 Grade A S235JR tai
vastaava / or equal
SFS-EN 10025-2 -
Tiiviste PN 25 Gasket PN 25
SFS-EN 1514–1, tyyppi IBC SFS-EN 1514–1, type IBC
2) - -
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201. Ruuvin
lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella.
3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole vaikutusta
mekaanisiin ominaisuuksiin.
4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin materiaalin
valmistajan antamiin materiaalitodistuksiin
5) Kierteellisten putkenosien suurin suositeltava nimelliskoko on DN 50.
1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4.
See standard PSK 4201. Starting material shall comply with requirements in SFS-EN 10269.
2) The gasket material and thickness are determined by the fluid and process conditions.
3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C but this has no
effect on mechanical properties.
4) The fittings or their packages must have markings, by which the fittings can be connected to related material certificates
given by the supplier.
5) The maximum recommended size for threaded pipe fittings is DN 50.
PSK Standardisointi PSK 4208 E25C1B 10 (16)
5 PUTKILUOKAN SALLITUT
KÄYTTÖPAINEET JA LÄMPÖTILAT 5 THE ALLOWABLE OPERATING
PRESSURES AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 25 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen.
The pipes and fittings belonging to this pipe class have been designed to resist 25 bar overpressure in 20 °C temperature, and the maximum allowable temperature is 400 °C. The vacuum resistance is according to standard PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa saadaan kuvasta 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan kerto-malla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 25) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 25).
Yli 400 °C lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4208 E25C1B 11 (16)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 Allowable pressures (bar) as a function of temperature Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 25). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine.
Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN 25). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
26,9 2,3 43,4 46,6 Harmaalla merkityt haaroitukset eivät kestä putkiluokan nimellispainetta Branches with grey shadowing do not resist the nominal pressure of the pipe class
711 14,2 39,7 38,8 37,7 36,1 35,1 33,5 31,3 30,0 27,6 25,6 23,8 22,3 19,2 17,8 17,5 16,7 16,4 16,0 15,3 15,1 1) Haaroituksen kulma on 90° ± 5°. Haaroituksen molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon 1) The angle of the branch connection is 90° ± 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in.
PSK Standardisointi PSK 4208 E25C1B 13 (16)
OPASTAVIA TIETOJA INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille:
General calculation criteria for piping components of pipe class:
- mitoitus SFS-EN 13480-3 mukaan - ylipaine 2,5 MPa - lämpötila 20 °C - suunnittelujännitys f = 150 MPa - korroosiovara c0 = 1,0 mm - hitsausliitoksen lujuuskerroin z = 1,0
- dimensioning in accordance with SFS-EN 13480-3
- overpressure 2,5 MPa - temperature 20 °C - design stress f = 150 MPa - corrosion allowance c0 = 1,0 mm - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmistustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
putket: pipes:
- 12,5 % tai 0,4 mm, kun DN ≤ 200 - 20 %, kun DN > 200
- 12,5 % or 0,4 mm, when DN ≤ 200 - 20 %, when DN > 200
käyrät, kartiot, T-putket ja päädyt: elbows, reducers, tee pieces and caps:
- 12,5 %, kun DN ≤ 600 - 0,5 mm, kun DN > 600
- 12,5 %, when DN ≤ 600 - 0,5 mm, when DN > 600
Kartioiden laskenta on tehty epäkeskeisille kartioille. Kartiot on laskettu muovattuina DN 500:aan asti ja levykartioina DN 600:sta ylöspäin.
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and upwards from DN 600 as straight reducers.
PSK Standardisointi PSK 4208 E25C1B 14 (16)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4208 E25C1B 15 (16)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
Kuva 3 Istutusten viistäminen
Figure 3 Bevelling of branches
O.3 Nimikkeen muodostaminen O.3 Forming of designation
Examples of designations: - Pipe 114,3 x 3,6 - SFS-EN 10216-2 - P235GH
- TC 1 - Elbow 114,3 x 3,6 - SFS-EN 10253-2 - type A -
3D - 90° - P235GH - Reducer E1) 114,3 x 3,6 - 88,9 x 3,2 - SFS-EN
10253-2 - type A - P235GH - Tee 114,3 x 4,5 - 114,3 x 4,5 - SFS-EN 10253-
2 - type A - P235GH - Welding neck flange DN 100 - SFS-EN 1092-1
- PN 25 - 11 - B1 - P250GH - Cap 114,3 x 3,6 - SFS-EN 10253-2 - type A -
P235GH - Gasket DN 100 - PN 25 - type IBC – 1,5 mm -
SFS-EN 1514-1 - graphite laminate 2)
1) E = epäkeskeinen, K = keskeinen 1) E = eccentric, K = concentric 2) Tiivistemateriaalin valinta ja tiivisteen paksuus
määräytyvät virtaavan aineen ja prosessiolo-suhteiden mukaan.
2) The selection of the gasket material and thickness shall be determined by the fluid and process conditions
PSK Standardisointi PSK 4208 E25C1B 16 (16)
O.4 Putkiluokan tunnus O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokkamerkintää.
The letter E in the beginning of the identification code of the pipe class shows that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältö poikkeaa tässä standardissa esitetystä.
A different identification code shall be given to the pipe class, if the contents deviate from this standard.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting materials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been replaced by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- DN700 käyrän säde on korjattu vastaamaan viitestandardin mittaa
- The radius of DN700 elbow has been revised to comply with reference standard
- Putkiluokan suunnittelujännitys f kohdassa O.1 muutettu.
- The design stress f in section O.1 has been changed
- Kuva 1 ja taulukko 4 on muutettu vastaamaan uutta suunnittelujännityksen arvoa.
- Figure 1 and table 4 have been revised to match the new design stress
PUTKILUOKKA E40C1B PAINELAITEKÄYTTÖÖN. KUUMALUJA SEOSTAMATON TERÄS. SAUMATON TERÄSPUTKI Pipe class E40C1B for pressure purposes. Seamless non-alloy steel pipe for elevated temperatures
Ristiriitatapauksissa pätee suomenkielinen teksti In the case of a conflict the Finnish text shall prevail.
Sisällys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5 Putkiluokan sallitut käyttöpaineet ja lämpötilat Opastavia tietoja O.1 Laskentaperusteet O.2 Hitsausviisteet O.3 Nimikkeen muodostaminen O.4 Putkiluokan tunnus O.5 Muutokset standardin edelliseen painokseen
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The allowable operating pressures and
temperatures Information for guidance O.1 Calculation criteria O.2 Bevelling O.3 Forming of designation O.4 Identification of the pipe class O.5 Amendments to the previous edition of the
standard
1 SOVELTAMISALA 1 SCOPE
Tässä standardissa esitetään putkiluokkaan E40C1B kuuluvien painelaitekäyttöön tarkoitettujen putkien ja putkenosien materiaalit, mitat ja putkiluokan paineenkestävyys. Tämän putkiluokan suurin sallittu paine on 40 bar lämpötilassa 20 °C ja suurin sallittu lämpötila 400 °C.
This standard specifies the materials and dimensions of the pipes and fittings belonging to the pipe class E40C1B, as well as the pressure rating of the pipe class. In this pipe class the allowable pressure at temperature 20 °C is 40 bar and the maximum allowable temperature is 400 °C.
Putkiluokkien määrittely on esitetty standardissa PSK 4201 ja lisäksi standardeissa SFS-EN 13480-2…5 on määritelty muita putkiston suunnittelussa ja valmistuksessa huomioon otettavia vaatimuksia.
The definition of the pipe classes is introduced in standard PSK 4201. Additional requirements to be taken into account in piping design and manufacturing are defined in standard SFS-EN 13480 parts 2…5.
SFS-EN 1092-1:2018 Laipat ja laippaliitokset. Pyöreät laipat putkille, venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1: Teräksiset laipat. 2018
SFS-EN 1092-1:2018:en Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, PN designated. Part 1: Steel flanges. 2018
SFS-EN 1514-1:en Laipat ja yhteet. PN-mitoitettujen laippojen tiivisteiden mitat. Osa 1: Ei-metalliset tasotiivisteet. 1997
SFS-EN 1514-1:en Flanges and their joints. Dimensions of gaskets for PN-designated flanges. Part 1: Non-metallic flat gaskets with or without inserts. 1997
SFS-EN 10025-2:2019:en Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels. 2019
SFS-EN 10028-2:2017 Painelaiteteräkset. Levy-tuotteet. Osa 2: Kuumalujat seostamattomat ja seostetut teräkset. 2017
SFS-EN 10028-2:2017:en Flat products made of steels for pressure purposes. Part 2: Non-alloy and alloy steels with specified elevated temperature properties. 2017
SFS-EN 10204 Metallic products. Types of inspection documents. 2004
SFS-EN 10216-2:2014 + A1:2019 Saumattomat painelaiteteräsputket. Tekniset toimitusehdot. Osa 2: Kuumalujat seostamattomat ja seostetut teräsputket. 2014
SFS-EN 10216-2:2014 + A1:2019:en Seamless steel tubes for pressure purposes. Technical delivery conditions. Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties. 2014
SFS-EN 10222-2:2017 Painelaiteteräkset. Takeet. Osa 2: Kuumalujat ferriittiset ja martensiittiset teräkset. 2017
SFS-EN 10222-2:2017:en Steel forgings for pressure purposes. Part 2: Ferritic and martensitic steels with specified elevated temperatures properties. 2017
SFS-EN 13480-2:2017/A1:2018/A2:2018/ A3:2018/A7:2020:en Metallic industrial piping. Part 2: Materials. 2017
SFS-EN 13480-3:2017 + A2:2020 + A3:2020 Metalliset teollisuusputkistot. Osa 3: Suunnittelu ja laskenta. 2017
SFS-EN 13480-3:2017/A2:2020/A3:2020:en Metallic industrial piping. Part 3: Design and calculation. 2017
SFS-EN 13480-4:2017 Metalliset teollisuusputkistot. Osa 4: Valmistus ja asennus. 2017
SFS-EN 13480-4:2017:en Metallic industrial piping. Part 4: Fabrication and installation. 2017
SFS-EN 13480-5:2017 + A1:2019 Metalliset teollisuusputkistot. Osa 5: Tarkastus ja testaus. 2017
SFS-EN 13480-5:2017/A1:2019:en Metallic industrial piping. Part 5: Inspection and testing. 2017
PSK Standardisointi PSK 4209 E40C1B 3 (17)
SFS-EN ISO 898-1 Kiinnityselimien lujuusominaisuudet. Seostamattomat ja seos-teräkset. Osa 1: Ruuvien ja vaarnaruuvien lujuusluokat. Vakiokierre ja taajakierre. 2013
SFS-EN ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread (ISO 898-1:2013). 2013
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 898-2:en Mechanical properties of fasteners made of carbon steel and alloy steel. Part 2: Nuts with specified property classes. Coarse thread and fine pitch thread (ISO 898-2:2012). 2012
SFS-EN ISO 4014:en Osakierteiset kuusioruuvit. Tarkkuusluokat A ja B. 2011
SFS-EN ISO 4014:en Hexagon head bolts. Product grades A and B (ISO 4014:2011). 2011
SFS-EN ISO 4032 Kuusiomutterit, malli 1. Tarkkuusluokat A ja B. 2013
SFS-EN ISO 4032 Hexagon nuts, style 1. Product grades A and B (ISO 4032:2012). 2013
SFS-EN ISO 7089:en Pyöreät aluslaatat. Normaalikokoiset. Tarkkuusaste A. 2001
SFS-EN ISO 7089:en Plain washers. Normal series. Product grade A (ISO 7089:2000). 2001
3 MATERIAALIT 3 MATERIALS
Tähän putkiluokkaan kuuluvien putkien materiaali on seostamaton teräs P235GH, SFS-EN 10216-2.
The material of pipes belonging to this pipe class is non-alloy steel P235GH, SFS-EN 10216-2.
Käyrien, kartioiden, päätyjen ja T-putkien materiaali on seostamaton teräs P235GH, SFS-EN 10253–2.
The material of elbows, reducers, caps and tees is non-alloy steel P235GH, SFS-EN 10253-2.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty taulukossa 3.
The materials of other components belonging to this pipe class are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standardin SFS-EN 10204 mukainen ainestodistus 3.1, josta tulee ilmetä, että materiaalin valmistajalla on Euroopan yhteisöön sijoittuneen toimivaltaisen elimen sertifioima laatujärjestelmä, joka kattaa kyseisen materiaalityypin valmistuksen. Muiden putkiluokkaan kuuluvien osien ainestodistus-vaatimukset on esitetty taulukossa 3.
Material certificate 3.1 according to standard SFS-EN 10204 is required for pipes, fittings and flanges. The certificate shall demonstrate that the manufacturer of the material has a quality system certified by an authorized body in EU, which covers manufacturing of the material type in question. The requirements of material certificates for the other components belonging to this pipe class are specified in Table 3.
Putkenosien mukana on lisäksi toimitettava valmistajan laatima todistus, josta selviää standardin SFS-EN 10253-2 vaatimat valmistustiedot.
Additionally, manufacturer's certificate specifying the manufacturing information according to standard SFS-EN 10253-2 shall be delivered with the pipe fittings.
PSK Standardisointi PSK 4209 E40C1B 4 (17)
4 MITAT 4 DIMENSIONS
Putkiluokkaan E40C1B kuuluvien putkien ja putkenosien mitat ja mittastandardit on esitetty taulukoissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to the pipe class E40C1B are shown in Tables 1, 2 and 3.
Kaikki putkenosat ovat standardin SFS-EN 10253-2 tyyppiä A, joilla seinämänpaksuus on sama liitospäissä ja osan keskellä. Seinämät voidaan tarvittaessa viistää hitsauspäissä vastaamaan liittyvää komponenttia.
All the pipe fittings are of type A according to standard SFS-EN 10253-2. Their wall thickness is the same in weld ends and in the middle of the fitting. It might be necessary to bevel the wall in weld ends to correspond the connected component.
1) Mitat koskevat myös epäkeskeisiä kartioita. 1) The dimensions apply also to eccentric reducers.
PSK Standardisointi PSK 4209 E40C1B 9 (17)
Taulukko 2 Laippojen mitat Table 2 The dimensions of flanges
PN 40
SFS-EN 1092-1
Tyyppi 11 Type 11
DN D K
Ruuvit Bolts H2 C2
Sokeointilevy
Spade Määrä
Quantity Koko Size d 1) s
15 95 65 4 M12 38 16 51
Kts./See PSK 7820
20 105 75 4 M12 40 18 61
25 115 85 4 M12 40 18 71
32 140 100 4 M16 42 18 82
40 150 110 4 M16 45 18 92
50 165 125 4 M16 48 20 107
65 185 145 8 M16 52 22 127
80 200 160 8 M16 58 24 142
100 235 190 8 M20 65 24 168
125 270 220 8 M24 68 26 194
150 300 250 8 M24 75 28 224
200 375 320 12 M27 88 34 290
250 450 385 12 M30 105 38 352
300 515 450 16 M30 115 42 417
350 580 510 16 M33 125 46 474
400 660 585 16 M36 135 50 546
450 685 610 20 M36 135 57 571
500 755 670 20 M39 140 57 628
600 890 795 20 M45 150 72 747 1) Tiivisteen ulkohalkaisija 1) Outside diameter of the gasket
PSK Standardisointi PSK 4209 E40C1B 10 (17)
Taulukko 3 Laippojen, umpilaippojen, kierteellisten putkenosien, ruuvien, mutterien, aluslaattojen ja tiivisteiden mittastandardit ja materiaalit Table 3 The dimension standards and materials of flanges, blind flanges, threaded pipe fittings, bolts, nuts, washers and gaskets
Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Merkintä Marking
Standardi Standard
Todistus Certificate
Kauluslaippa PN 40 Welding neck flange PN 40
SFS-EN 1092–1, tyyppi 11-B1 SFS-EN 1092–1, type 11-B1
P250GH SFS-EN 10222-2 3.1
Umpilaippa PN 40 Blind flange PN 40
SFS-EN 1092–1, tyyppi 05 SFS-EN 1092–1, type 05
P265GH SFS-EN 10028-2 3.1
Sokeointilevy Spade
PSK 7820 P265GH SFS-EN 10028-2 3.1
Kierteelliset putkenosat 4) 5)
Threaded pipe fittings SFS-EN 10241 P235GH tai / or
P250GH SFS-EN 10273 SFS-EN 10222-2
3.1
Ruuvi 3) 4)
Bolt SFS-EN ISO 4014 25CrMo4
5.6 1) (T < 50 °C) SFS-EN 10269 SFS-EN ISO 898-1
3.1 2.2
Mutteri 3) 4)
Nut SFS-EN ISO 4032
25CrMo4 5 (T ≤ 50 °C)
SFS-EN 10269 SFS-EN ISO 898-2
3.1 2.2
Aluslaatta 3)
Washer SFS-EN ISO 7089 Grade A S235JR tai
vastaava / or equal SFS-EN 10025-2 -
Tiiviste PN 40 Gasket PN 40
SFS-EN 1514-1, tyyppi IBC SFS-EN 1514-1, type IBC
2) - -
1) Materiaali vaatii erityisarvioinnin (PMA), ellei toimitusstandardi ole SFS-EN 1515-4. Katso standardi PSK 4201. Ruuvin
lähtöaineen pitää täyttää SFS-EN 10269 vaatimukset.
2) Tiivisteen materiaali ja paksuus määritellään sisällön ja prosessiolosuhteiden perusteella.
3) Pintakäsittelynä on yleensä kuumasinkitys. Se alkaa kuitenkin hävitä yli 200 °C lämpötilassa, mutta tällä ei ole vaikutusta
mekaanisiin ominaisuuksiin.
4) Osissa tai niiden pakkauksissa tulee olla merkinnät, joiden perusteella osat voidaan yhdistää niitä koskeviin materiaalin
valmistajan antamiin materiaalitodistuksiin
5) Kierteellisten putkenosien suurin suositeltava nimelliskoko on DN 50.
1) The material requires a particular material appraisal (PMA), unless delivered according to SFS-EN 1515-4. See standard
PSK 4201. Starting material shall comply with requirements in SFS-EN 10269.
2) The gasket material and thickness are determined by the fluid and process conditions.
3) Typical surface treatment is hot dip galvanization. However, it starts to dissipate in temperatures over 200 °C but this has no
effect on mechanical properties.
4) The fittings or their packages must have markings, by which the fittings can be connected to related material certificates
given by the supplier.
5) The maximum recommended size for threaded pipe fittings is DN 50.
PSK Standardisointi PSK 4209 E40C1B 11 (17)
5 PUTKILUOKAN SALLITUT KÄYTTÖ-
PAINEET JA LÄMPÖTILAT 5 THE ALLOWABLE OPERATING
PRESSURES AND TEMPERATURES OF THE PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kestämään 40 bar ylipaine 20 °C lämpötilassa ja suurin sallittu lämpötila on 400 °C. Alipaineen kesto on standardin PSK 4299 mukainen.
The pipes and fittings belonging to this pipe class have been designed to resist 40 bar overpressure in 20 °C temperature and the maximum allowable temperature is 400 °C. The vacuum resistance is according to standard PSK 4299.
Putkiluokan paineenkestävyys (poikkeuksena istutettu haaroitus) eri lämpötiloissa on esitetty kuvassa 1.
The pressure resistance of the pipe class (except branch connection) in different temperatures is given in Figure 1.
20 °C arvoa voidaan käyttää 50 °C asti. 50 °C ja 100 °C välillä olevat arvot interpoloidaan lineaarisesti 20 °C ja 100 °C arvojen avulla.
Value of 20 °C can be used up to 50 °C. Values between 50 °C and 100 °C are linearly interpolated by values of 20 °C and 100 °C.
Istutetun kohtisuoran haaroituksen paineenkestävyys eri lämpötiloissa saadaan kerto-malla taulukon 4 arvo kuvasta 1 saatavan sallitun paineen ja putkiluokan nimellispaineen (PN 40) suhteella.
The pressure resistance of a perpendicular branch connection in different temperatures is calculated by multiplying the value from Table 4 with the ratio of the allowable pressure from Figure 1 and the nominal pressure (PN 40).
Yli 400 °C lämpötiloissa mitoitukset ja materiaalien kelpoisuudet on erikseen tarkistettava.
In temperatures over 400 °C the dimensioning and the acceptability of the materials must be checked separately.
Putkiluokan alin sallittu käyttölämpötila on -40 °C käytettäessä ruuvi- ja mutterimateriaalia 25CrMo4.
The lowest allowable operating temperature of the pipe class is -40 °C when using bolting material 25CrMo4.
Lujuusluokan 5.6 ruuveja käytettäessä putkiluokan alin sallittu käyttölämpötila on -10 °C. M16 ja suuremmille ruuveille edellytetään, että ruuvit täyttävät SFS-EN 13480-2 kohdan B.2.2.4 vaatimukset.
When using bolting material of strength class 5.6 the lowest allowable operating temperature of the pipe class is -10 °C. For bolt sizes M16 or larger the requirements of SFS-EN 13480-2 clause B.2.2.4 shall be applied.
Alin sallittu käyttölämpötila -40 °C edellyttää lisäksi, että paksuudeltaan yli 22 mm putkissa ja putkenosissa olevat hitsausliitokset lämpökäsitellään. Tämä vaatimus ei koske tämän standardin mukaisia laippoja ja sokeointilevyjä. Muiden putkistokomponenttien ja ratkaisujen osalta, katso SFS-EN 13480-2, taulukko B.4-1.
The lowest allowable operating temperature -40 °C requires also that the weld joints of pipes and pipe components with wall thickness over 22 mm shall be heat treated. This requirement does not apply to flanges and spades according to this standard. For other piping components and applications, see SFS-EN 13480-2, table B.4-1.
PSK Standardisointi PSK 4209 E40C1B 12 (17)
Kuva 1 Sallitut paineet (bar) lämpötilan funktiona Figure 1 Allowable pressures (bar) as a function of temperature
Huomautus 1. Väliarvot interpoloidaan lineaarisesti. Huomautus 2. Käyrän arvot on saatu putken, putkenosien ja laippojen materiaalistandardeissa kyseiseen lämpötilaan annetun myötörajan perusteella lasketun suunnittelujännityksen ja vastaavan huoneenlämpötilaan määritetyn suunnittelujännityksen suhdeluvuista. Näistä suhdeluvuista pienin on kerrottu putkiluokan nimellispaineella (PN 40). Huomautus 3. Lämpötila-alueella -40 … +50 °C putkiluokan suurin sallittu paine on yhtä suuri kuin nimellispaine.
Note 1. Intermediate values are linearly interpolated. Note 2. The values of the graph are calculated by the ratios of the design stress, based on the proof strength value in the reference temperature from the material standards of pipe, fittings and flange and respectively the design stress in room temperature. The smallest value has been multiplied by the nominal pressure (PN 40). Note 3. In temperature range -40 … +50 °C the maximum allowable pressure of the pipe class is equal to nominal pressure.
1) Haaroituksen kulma on 90° ± 5°. T-haaran molempien putkien on oltava tämän putkiluokan mukaisia. Haaraputken istutus voidaan tehdä runkoputken pintaan tai runkoputkessa olevaan aukkoon. 1) The angle of the branch connection is 90° ± 5°. Both pipes of the branch must be according to this pipe class. The branch connection can be done as set-on or set-in
PSK Standardisointi PSK 4209 E40C1B 14 (17)
OPASTAVIA TIETOJA INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille:
General calculation criteria for piping components of pipe class:
- mitoitus SFS-EN 13480-3 mukaan - dimensioning in accordance with SFS-EN 13480-3 - ylipaine 4,0 MPa - overpressure 4,0 MPa - lämpötila 20 °C - temperature 20 °C - suunnittelujännitys f = 150 MPa - design stress f = 150 MPa - korroosiovara c0 = 1,0 mm - corrosion allowance c0 = 1,0 mm - hitsausliitoksen lujuuskerroin z = 1,0 - joint factor of weld seam z = 1,0
Eri osien seinämille on käytetty seuraavia valmistustoleransseja:
The following manufacturing tolerances have been used for the wall thickness of various components:
Putket: Pipes:
- 12,5 % tai 0,4 mm, kun DN ≤ 200 - 12,5 % or 0,4 mm, when DN ≤ 200 - 20 %, kun DN > 200
- 20 %, when DN > 200
Käyrät, kartiot, T-putket ja päädyt: Elbows, reducers, tee pieces and caps:
- 12,5 %, kun DN ≤ 600 - 12,5 %, when DN ≤ 600 - 0,5 mm, kun DN > 600
- 0,5 mm, when DN > 600
Kartioiden laskenta on tehty epäkeskeisille kartioille. Kartiot on laskettu muovattuina DN 500:aan asti ja DN 600 on laskettu levykartioina
The calculation of reducers has been done for eccentric reducers. The reducers have been calculated up to DN 500 as wrought and DN 600 as straight reducer.
PSK Standardisointi PSK 4209 E40C1B 15 (17)
O.2 Hitsausviisteet O.2 Bevelling
T = ≤ 3 mm b = T mm
T = 3-12 mm b = 2-4 mm c = ≤ 2 mm
α = 60°
Kuva 2a I-railo Figure2a Square bevel
Kuva 2b V-railo Figure2b Single V-bevel
t = ≤ 12 mm b = 2-4 mm c = ≤ 2 mm
α 60° β ≤ 15°
T = > 12 mm b = 2-4 mm c = ≤ 2 mm
ϑ = 60°-90° φ = 10°-15°
Kuva 2c V-railo Figure2c Single V-bevel
Kuva 2d Erikois V-railo Figure2d Single V-bevel with V-root
Kuva 2 Hitsauspäiden viistäminen
Figure 2 Bevelling of welding ends
T = 3-12 mm b = 2-4 mm R = > 3 mm
ψ = 35°-60°
T = 3-12 mm b = 2-4 mm
ψ = 35°-60°
Kuva 3a Pintaan istutettu Figure 3a Set-on
Kuva 3b Upotettu istutus Figure 3b Set-in
PSK Standardisointi PSK 4209 E40C1B 16 (17)
T = 3-12 mm b = 2-4 mm R = > 3 mm d = 3-5 mm
ψ = 35°-60°
Kuva 3c Pintaan istutettu, levyvahvistus Figure 3c Set-on with reinforcing pad
Kuva 3 Istutusten viistäminen
Figure 3 Bevelling of branches
O.3 Nimikkeen muodostaminen O.3 Forming of designation
- Gasket DN 100 - PN 40 - type IBC – 1,5 mm - SFS-EN 1514-1 - graphite laminate 2)
1) E = epäkeskeinen, K = keskeinen 1) E = eccentric, K = concentric 2) Tiivistemateriaalin valinta ja tiivisteen paksuus
määräytyvät virtaavan aineen ja prosessiolo-suhteiden mukaan.
2) The selection of the gasket material and thickness shall be determined by the fluid and process conditions
PSK Standardisointi PSK 4209 E40C1B 17 (17)
O.4 Putkiluokan tunnus
O.4 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoittaa, että putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja ja se on olennainen osa putkiluokkamerkintää.
The letter E in the beginning of the identification code of the pipe class shows, that the pipe class complies with the harmonized European standards and it is an integral part of the pipe class identification.
Putkiluokalle annetaan eri tunnus, jos sen sisältö poikkeaa tässä standardissa esitetystä.
A different identification code shall be given to the pipe class, if the contents deviate from this standard.
O.5 Muutokset standardin edelliseen painokseen
O.5 Amendments to the previous edition of the standard
Putkiluokkaan on tehty muutoksia ja korjauksia. Seuraavassa on lueteltu merkittävimmät:
The pipe class has been revised and corrected. The most significant changes are:
- Ruuvi- ja mutterimateriaalien käyttölämpötila-alueet on korjattu vastaamaan standardia SFS-EN 13480-2
- The operating temperature range of the bolting materials has been changed to comply with SFS-EN 13480-2
- Taulukossa 2 sokeointilevyjen paksuudet on korvattu viittauksella standardiin PSK 7820
- The thicknesses of spades in table 2 have been replaced by reference to standard PSK 7820
- Putkiluokan alin käyttölämpötila on -40 °C tietyin rajoituksin
- The lowest operating temperature of the pipe class is -40 °C with certain restrictions
- Taulukkoon 3 lisätty sokeointilevyn materiaali - Spade material added in table 3 - Putkiluokan suunnittelujännitys f kohdassa O.1
muutettu. - The design stress f in section O.1 has been
changed - Kuva 1 ja taulukko 4 on muutettu vastaamaan
uutta suunnittelujännityksen arvoa. - Figure 1 and table 4 have been revised to