-
PSK Standardisointi STANDARDI PSK 4255 PSK Standards Association
E40H3A COPYRIGHT: PSK Standardisointiyhdistys ry 2009-04-16 1
(15)
MYYNTI: PSK Standardisointiyhdistys ry, PUH. (09) 72 880 880
WWW-OSOITE: www.psk-standardisointi.fi, SHKPOSTI
[email protected]
PUTKILUOKKA E40H3A PAINELAITEKYTTN. AUSTENIITTIS-FERRIITTINEN
RUOSTUMATON CrNiMo-TERS Pipe class E40H3A for pressure purposes.
Austenitic-ferritic stainless CrNiMo-steel
Ristiriitatapauksissa ptee suomenkielinen teksti. In the case of
a conflict the Finnish text shall prevail.
Sisllys 1 Soveltamisala 2 Viittaukset 3 Materiaalit 4 Mitat 5
Putkiluokan sallitut kyttpaineet ja lmptilat Opastavia tietoja O.1
Laskentaperusteet O.2 Nimikkeen muodostaminen O.3 Putkiluokan
tunnus
Contents 1 Scope 2 References 3 Materials 4 Dimensions 5 The
allowable operating pressures and tem-
peratures Information for guidance O.1 Calculation criteria O.2
Forming of designation O.3 Identification of the pipe class
1 SOVELTAMISALA
1 SCOPE
Tss standardissa esitetn putkiluokkaan E40H3A kuuluvien
painelaitekyttn tarkoitettujen putkien ja putkenosien materiaalit,
mitat ja putki-luokan paineenkestvyys. Tmn putkiluokan suu-rin
sallittu paine on 40 bar lmptilassa 20 C ja suurin sallittu lmptila
250 C.
This standard specifies the materials and dimen-sions of the
pipes and fittings belonging to the pipe class E40H3A, as well as
the pressure rating of the pipe class. In this pipe class the
allowable pres-sure at temperature 20 C is 40 bar and the maxi-mum
allowable temperature 250 C.
Putkiluokkien mrittely on esitetty standardissa PSK 4201 ja
lisksi standardeissa SFS-EN 13480-25 on mritelty muita putkiston
suunnittelussa ja valmistuksessa huomioon otettavia
vaatimuksia.
The definition of the pipe classes is introduced in standard PSK
4201. Additional requirements to be taken into account in piping
design and manufac-turing are defined in standard SFS-EN 13480
parts 25.
2 VIITTAUKSET
2 REFERENCES
PSK 4201 Putkiluokat. Mrittely. 2007
PSK 4201 Pipe classes. Definition. 2007
SFS-EN 1092-1 Laipat ja laippaliitokset. Pyret laipat putkille,
venttiileille, yhteille ja varusteille, PN-mitoitetut. Osa 1:
Terksiset laipat. 2007
SFS-EN 1092-1 Flanges and their joints - Circular flanges for
pipes, valves, fittings and accessories, PN designated - Part 1:
Steel flanges. 2007
SFS-EN 1514-1 Flanges and their joints. Di-mensions of gaskets
for PN-designated flanges. Part 1: Non-metallic flat gaskets with
or without inserts. 1997
SFS-EN 1514-1 Flanges and their joints. Dimen-sions of gaskets
for PN-designated flanges. Part 1: Non-metallic flat gaskets with
or without inserts. 1997
SFS-EN 10025-2 Kuumavalssatut rakenneterk-set. Osa 2:
Seostamattomat rakenneterkset. Tek-niset toimitusehdot. 2004
SFS-EN 10025-2 Hot rolled products of struc-tural steels. Part
2: Technical delivery conditions for non-alloy structural steels.
2004
SFS-EN 10028-2 Painelaiteterkset. Levytuotteet. Osa 2:
Kuumalujat seostamattomat ja seosterk-set. 2009
SFS-EN 10028-2 Flat products made of steels for pressure
purposes. Part 2: Non-alloy and alloy steels with specified
elevated temperature proper-ties. 2009
-
PSK Standardisointi PSK 4255 E40H3A 2 (15) SFS-EN 10028-7
Painelaiteterkset. Levytuotteet. Osa 7: Ruostumattomat terkset.
2007
SFS-EN 10028-7 Flat products made of steels for pressure
purposes. Part 7: Stainless steels. 2007
SFS-EN 10204 Metallituotteiden ainestodistuk-set. 2004
SFS-EN 10204 Metallic products. Types of inspec-tion documents.
2004
SFS-EN 10217-7 Hitsatut painelaitetersputket. Tekniset
toimitusehdot. Osa 7: Ruostumattomat tersputket. 2005
SFS-EN 10217-7 Welded steel tubes for pressure purposes.
Technical delivery conditions. Part 7: Stainless steel tubes
2005
SFS-EN 10222-5 Painelaiteterkset. Takeet. Osa 5:
Martensiittiset, austeniittiset ja austeniittis-ferriittiset
ruostumattomat terkset. 2000
SFS-EN 10222-5 Steel forgings for pressure purposes. Part 5:
Martensitic, austenitic and aus-tenitic-ferritic stainless steels.
2000
SFS-EN 10241 Steel threaded pipe fittings. 2000
SFS-EN 10241 Steel threaded pipe fittings. 2000
SFS-EN 10253-4 Pittishitsattavat putkenosat. Osa 4:
Toimituserkohtaisesti tarkastettavat aus-teniittiset ja
austeniittis-ferriittiset (duplex) terkset. 2008
SFS-EN 10253-4 Butt-welding pipe fittings-Part 4: Wrought
austenitic and austenitic-ferritic (duplex) stainless steels with
specific inspection require-ments. 2008
SFS-EN 10272 Painelaiteterkset. Ruostumat-tomat terstangot.
2007
SFS-EN 10272 Stainless steel bars for pres-sure purposes.
2007
SFS-EN 13480-2 Metalliset teollisuusputkistot. Osa 2:
Materiaalit. 2002
SFS-EN 13480-2 Metallic industrial piping. Part 2: Materials.
2002
SFS-EN 13480-3 Metallic industrial piping. Part 3: Design and
calculation. 2002
SFS-EN 13480-3 Metallic industrial piping. Part 3: Design and
calculation. 2002
SFS-EN 13480-3 + A1 Metalliset teollisuusputkis-tot. Osa 3:
Suunnittelu ja laskenta. 2006
SFS-EN 13480-3 + A1 Metallic industrial piping. Part 3: Design
and calculation. 2006
SFS-EN 13480-3/A2 Metallic industrial piping. Part 3: Design and
calculation. 2007
SFS-EN 13480-3/A2 Metallic industrial piping. Part 3: Design and
calculation. 2007
SFS-EN 13480-4 Metalliset teollisuusputkistot. Osa 4: Valmistus
ja asennus. 2002
SFS-EN 13480-4 Metallic industrial piping. Part 4: Fabrication
and installation. 2002
SFS-EN 13480-5 Metalliset teollisuusputkistot. Osa 5: Tarkastus
ja testaus. 2002
SFS-EN 13480-5 Metallic industrial piping. Part 5: Inspection
and testing. 2002
SFS-EN 20898-2 Kiinnityselinten lujuusominai-suudet. Osa 2:
Mutterit. Metrinen kierre. 1994
SFS-EN 20898-2 Mechanical properties of fasten-ers. Part 2: Nuts
with specified proof load values. Coarse thread. 1994
SFS-EN ISO 898-1 Kiinnityselimien lujuusomi-naisuudet.
Seostamattomat ja seosterkset. Osa 1: Ruuvit ja vaarnaruuvit.
2000
SFS-EN ISO 898-1 Mechanical properties of fas-teners made of
carbon steel and alloy steel. Part 1: Bolts, screws and studs.
2000
SFS-EN ISO 4014 Hexagon head bolts. Product grades A and B.
2001
SFS-EN ISO 4014 Hexagon head bolts. Product grades A and B.
2001
SFS-EN ISO 4032 Hexagon nuts, style 1. Product grades A and B.
2001
SFS-EN ISO 4032 Hexagon nuts, style 1. Product grades A and B.
2001
SFS-EN ISO 7089 Plain washers. Normal series. Product grades A.
2001
SFS-EN ISO 7089 Plain washers. Normal series. Product grade A.
2001
-
PSK Standardisointi PSK 4255 E40H3A 3 (15) 3 MATERIAALIT
3 MATERIALS
Thn putkiluokkaan kuuluvien DN 10DN 400 putkien materiaali on
austeniittis-ferriittinen ruos-tumaton ters 1.4462 (X2CrNiMoN
22-5-3) SFS-EN 10217-7.
The material of pipes DN 10 ... DN 400 belonging to this pipe
class is austenitic-ferritic steel 1.4462 (X2CrNiMoN 22-5-3) SFS-EN
10217-7.
Kyrien, kartioiden, T-putkien, ptyjen ja putki-kaulusten
materiaali on austeniittis-ferriittinen ruos-tumaton ters 1.4462
(X2CrNiMoN 22-5-3), SFS-EN 10253-4.
The material of elbows, reducers, tees, caps and collars is
austenitic-ferritic steel 1.4462 (X2CrNiMoN 22-5-3), SFS-EN
10253-4.
Muiden putkiluokkaan kuuluvien osien materiaalit on esitetty
taulukossa 3.
The materials of other components belonging to this pipe class
are specified in Table 3.
Putkille, putkenosille ja laipoille vaaditaan standar-din SFS-EN
10204 mukainen ainestodistus 3.1, mist tulee ilmet, ett materiaalin
valmistajalla on Euroopan yhteisn sijoittuneen toimivaltaisen
eli-men sertifioima laatujrjestelm, joka kattaa kysei-sen
materiaalityypin valmistamisen. Muiden putki-luokkaan kuuluvien
komponenttien ainestodistus-vaatimukset on esitetty taulukossa
3.
Material certificate 3.1 according to standard SFS-EN 10204 is
required for pipes, fittings and flanges. The certificate shall
demonstrate that the manufacturer of the material has a quality
system certified by an authorized body in EU, which cov-ers
manufacturing of the material type in question. The requirements of
material certificates for the other components belonging to this
pipe class are specified in Table 3.
Tilauksessa on huomioitava, ett standardin SFS-EN 10217-7 mukaan
merkinnll C1 varustettua putkea saa kytt korkeintaan luokkaan I
kuulu-viin putkistoihin ja merkinnll C2 varustettua put-kea
korkeintaan luokkaan II kuuluviin putkistoihin.
When ordering it shall be taken into account that according to
standards SFS-EN 10217-7 the pipes marked with C1 are allowed to be
used in piping belonging to category I at the most. The pipes
marked with C2 are allowed to be used in category II at the
most.
Putkenosien mukana on lisksi toimitettava valmis-tajan laatima
todistus, josta selvi standardin SFS-EN 10253-4 vaatimat
valmistustiedot.
Additionally, manufacturer's certificate specifying the
manufacturing information according to stan-dard SFS-EN 10253-4
shall be delivered with the pipe fittings.
-
PSK Standardisointi PSK 4255 E40H3A 4 (15) 4 MITAT
4 DIMENSIONS
Putkiluokkaan E40H3A kuuluvien putkien ja put-kenosien mitat ja
mittastandardit on esitetty taulu-koissa 1, 2 ja 3.
The dimensions and standards of pipes and fittings belonging to
the pipe class E40H3A are shown in Tables 1, 2 and 3.
Kaikki putkenosat ovat standardiehdotuksen SFS-EN 10253-4 tyyppi
A, joilla seinmnpaksuus on sama liitospiss ja osan keskell.
Seinmn-paksuudet voidaan joutua tarvittaessa viistmn hitsauspiss
vastaamaan liittyv komponenttia.
All pipe fittings are of type A according to standard SFS-EN
10253-4. Their wall thickness is the same in weld ends and in the
middle of the fitting. It might be necessary to bevel the wall at
weld ends to correspond the connected component.
Muotokappaleiden seinmnpaksuudet taulukossa 1 voivat poiketa
standardissa SFS-EN 10253-4 esitetyist paksuuksista.
Wall thicknesses of the pipe fittings in Table 1 may deviate
from those specified in SFS-EN 10253-4.
Taulukko 1 Putkien, kyrien, ptyjen, kartioiden ja T-putkien
mitat (mm) Table 1 The dimensions of pipes, elbows, caps, reducers
and tees (mm)
Putki
Pipe
Kyr
Elbow
Pty
Cap
SFS-EN 10217-7
SFS-EN 10253-4
SFS-EN 10253-4
Kartio
Reducer
T-putki
Tee
SFS-EN 10253-4
SFS-EN 10253-4
Nimellis-koko
Ulko-halkaisija
Putki Kyr
Pty Nimellis-koko
Ulko-halkaisija
Kartio 1) T-putki
Nominal size
Outer diameter
Pipe Elbow Cap Nominal size
Outer diameter
Reducer 1) Tee
DN D T T R 2) T K DN1 D1 T T1 L T T1 F G
10 17,2 1,6 1,6 38 - - - - - - - - - - -
15 21,3 1,6 1,6 28 1,6 25 15 21,3 - - - 1,6 1,6 25 25
10 17,2 1,6 - 12 - - - -
20 26,9 1,6 1,6 29 1,6 25 20 26,9 - - - 1,6 1,6 29 29
15 21,3 1,6 - 17 1,6 1,6 29 29
10 17,2 1,6 - 29 - - - -
25 33,7 1,6 1,6 38 1,6 38 25 33,7 - - - 1,6 1,6 38 38
20 26,9 1,6 - 20 1,6 1,6 38 38
15 21,3 1,6 - 37 1,6 1,6 38 38
-
PSK Standardisointi PSK 4255 E40H3A 5 (15) Nimellis-koko
Ulko-halkaisija
Putki Kyr
Pty Nimellis-koko
Ulko-halkaisija
Kartio 1) T-putki
Nominal size
Outer diameter
Pipe Elbow Cap Nominal size
Outer diameter
Reducer 1) Tee
DN D T T R 2) T K DN1 D1 T T1 L T T1 F G
32 42,4 1,6 1,6 48 1,6 38 32 42,4 - - - 1,6 1,6 48 48
25 33,7 1,6 - 26 1,6 1,6 48 48
20 26,9 1,6 - 46 1,6 1,6 48 48
15 21,3 - - - 1,6 1,6 48 48
40 48,3 1,6 1,6 57 1,6 38 40 48,3 - - - 1,6 1,6 57 57
32 42,4 1,6 - 17 1,6 1,6 57 57
25 33,7 1,6 - 43 1,6 1,6 57 57
20 26,9 1,6 - 63 1,6 1,6 57 57
50 60,3 1,6 1,6 76 1,6 38 50 60,3 - - - 1,6 1,6 125 125
40 48,3 1,6 - 36 1,6 1,6 125 125
32 42,4 1,6 - 53 1,6 1,6 125 125
25 33,7 1,6 - 79 1,6 1,6 125 125
20 26,9 1,6 - 99 - - - -
65 76,1 1,6 1,6 95 1,6 38 65 76,1 - - - 2 2 140 140
50 60,3 1,6 - 47 2 1,6 140 140
40 48,3 1,6 - 82 2 1,6 140 140
32 42,4 1,6 - 100 2 1,6 140 140
25 33,7 1,6 - 126 - - - -
80 88,9 2 2 114 2 51 80 88,9 - - - 2,6 2,6 150 150
65 76,1 2 - 38 2,6 1,6 150 150
50 60,3 2 - 85 2,6 1,6 150 150
40 48,3 2 - 120 2,6 1,6 150 150
32 42,4 2 - 138 - - - -
100 114,3 2 2 152 2 64 100 114,3 - - - 3,2 3,2 160 160
80 88,9 2 - 75 3,2 2,6 160 160
65 76,1 2 - 113 3,2 1,6 160 160
50 60,3 2 - 160 3,2 1,6 160 160
40 48,3 2 - 195 - - - -
-
PSK Standardisointi PSK 4255 E40H3A 6 (15) Nimellis-koko
Ulko-halkaisija
Putki Kyr
Pty Nimellis-koko
Ulko-halkaisija
Kartio 1) T-putki
Nominal size
Outer diameter
Pipe Elbow Cap Nominal size
Outer diameter
Reducer 1) Tee
DN D T T R 2) T K DN1 D1 T T1 L T T1 F G
125 139,7 2 2 190 2 76 125 139,7 - - - 4 4 180 180
100 114,3 2 - 75 4 3,2 180 180
80 88,9 2 - 151 4 2,6 180 180
65 76,1 2 - 188 4 1,6 180 180
50 60,3 2 - 235 - - - -
150 168,3 2 2,6 229 2 89 150 168,3 - - - 5 5 200 200
125 139,7 2,6 - 85 5 4 200 200
100 114,3 2,6 - 160 5 3,2 200 200
80 88,9 2,6 - 235 5 2,6 200 200
65 76,1 2,6 - 273 - - - -
200 219,1 2,6 3,2 305 2,6 102 200 219,1 - - - 6,3 6,3 250
250
150 168,3 3,2 - 150 6,3 5 250 250
125 139,7 3,2 - 235 6,3 4 250 250
100 114,3 3,2 - 310 6,3 3,2 250 250
80 88,9 3,2 - 385 - - - -
250 273 3,2 4 381 3,2 127 250 273 - - - 6,3 6,3 300 300
200 219,1 4 - 160 6,3 5 300 300
150 168,3 4 - 310 6,3 4 300 300
125 139,7 4 - 395 6,3 3,2 300 300
100 114,3 4 - 470 - - - -
300 323,9 4 5 457 4 152 300 323,9 - - - 8 8 330 330
250 273 4 - 151 8 6,3 330 330
200 219,1 4 - 310 8 5 330 330
150 168,3 4 - 461 8 4 330 330
125 139,7 4 - 545 - - - -
350 355,6 5 5 533 5 165 350 355,6 - - - 10 10 360 360
300 323,9 5 - 94 10 8 360 360
250 273 5 - 244 10 6,3 360 360
200 219,1 5 - 404 10 5 360 360
150 168,3 5 - 554 - - - -
-
PSK Standardisointi PSK 4255 E40H3A 7 (15) Nimellis-koko
Ulko-halkaisija
Putki Kyr Pty Nimellis-koko
Ulko-halkaisija
Kartio 1) T-putki
Nominal size
Outer diameter
Pipe Elbow Cap Nominal size
Outer diameter
Reducer 1) Tee
DN D T T R 2) T K DN1 D1 T T1 L T T1 F G
400 406,4 6,3 6,3 610 6,3 178 400 406,4 - - - 10 10 400 400
350 355,6 6,3 - 150 10 8 400 400
300 323,9 6,3 - 244 10 8 400 400
250 273 6,3 - 395 10 6,3 400 400
200 219,1 6,3 - 554 - - - -
1) Mitat koskevat mys epkeskeisi kartioita. 2) Putkikoossa DN 10
kytetn putkitaivutusta. 1) The dimensions apply also to eccentric
reducers. 2) For size DN 10 a pipe bend is used.
-
PSK Standardisointi PSK 4255 E40H3A 8 (15)
Taulukko 2 Laippojen mitat Table 2 The dimensions of flanges
PN 40
SFS-EN 1092-1
tyyppi 11 type 11
tyyppi 02 & 35 type 02 & 35
Ruuvit Bolts
Sokeointilevy Spade
Umpilaipan vuorauslevy
Lining plate for blind flange
DN D K
Mr Quantity
Koko Size
H2 C2 H4 C1 F
d 1) s d 1) s
10 90 60 4 12 35 16 35 14 5 46 5 46 2 15 95 65 4 12 38 16 38 14
5 51 5 51 2 20 105 75 4 12 40 18 40 16 6 61 5 61 2 25 115 85 4 12
40 18 40 16 7 71 5 71 2 32 140 100 4 16 42 18 42 18 8 82 5 82 2 40
150 110 4 16 45 18 45 18 8 92 5 92 2 50 165 125 4 16 48 20 48 20 10
107 5 107 2 65 185 145 8 16 52 22 52 22 11 127 8 127 2 80 200 160 8
16 58 24 58 24 12 142 8 142 2
100 235 190 8 20 65 24 65 26 14 168 8 168 2 125 270 220 8 24 68
26 68 28 16 194 10 194 2 150 300 250 8 24 75 28 75 30 18 224 122)
224 2 200 375 320 12 27 88 34 88 36 20 290 152) 290 2 250 450 385
12 30 105 38 105 42 22 352 202) 352 2 300 515 450 16 30 115 42 115
52 25 417 202) 417 2 350 580 510 16 33 125 46 125 58 28 474 252)
474 2 400 660 585 16 36 135 50 135 65 32 546 252) 546 2
1) Ulkohalkaisija d = tiivisteen ulkohalkaisija 2) Yleens on
taloudellisempaa valmistaa paksu sokeointilevy seostamattomasta
terksest ja kytt ruostu-mattomasta terksest tehtyj vuorauslevyj. 1)
Outer diameter d = outer diameter of the gasket 2) Usually it is
more economic to make a thick spade from non alloy steel plate and
use stainless steel lining plates.
-
PSK Standardisointi PSK 4255 E40H3A 9 (15) Taulukko 3 Laippojen,
umpilaippojen, kierteellisten putkenosien, ruuvien, muttereiden,
aluslaattojen ja tiivis-teiden mittastandardit ja materiaalit Table
3 The dimension standards and materials of flanges, blind flanges,
threaded pipe fittings, bolts, nuts, washers and gaskets
Putkenosa Component
Mittastandardi Dimension standard
Materiaali Material
Nimike Designation
Standardi Standard
Todistus Certificate
Irtolaippa PN 40 1) Loose flange PN 40 1)
SFS-EN 1092-1, tyyppi 02 SFS-EN 1092-1, type 02 P265GH SFS-EN
10028-2 3.1
Kauluslaippa PN 40 2) Welding neck flange PN 40 2)
SFS-EN 1092-1, tyyppi 11-B1 SFS-EN 1092-1, type 11-B1 1.4462
SFS-EN 10222-5 3.1
Umpilaippa PN 40 1) Blind flange PN 40 1)
SFS-EN 1092-1, tyyppi 05 SFS-EN 1092-1, type 05 P265GH SFS-EN
10028-2 3.1
Kaulus PN 40 Collar PN 40
SFS-EN 1092-1, tyyppi 35 SFS-EN 1092-1, type 35 1.4462
6) 3.1
Sokeointilevy Spade - 1.4462 SFS-EN 10028-7 3.1
Kierteelliset putkenosat 7, 8) Threaded pipe fittings 7, 8)
SFS-EN 10241 1.4462 SFS-EN 10272 3.1
Umpilaipan vuorauslevy Lining plate - 1.4462 SFS-EN 10028-7
3.1
Ruuvi 3) Bolt 3) SFS-EN ISO 4014 5.6
5) SFS-EN ISO 898-1 2.2
Mutteri 3) Nut 3) SFS-EN ISO 4032 5 SFS-EN 20898-2 2.2
Aluslaatta 3) Washer 3) SFS-EN ISO 7089 Gr. A
S235JR tai vastaava SFS-EN 10025-2 -
Tiiviste PN 40 Gasket PN 40
SFS-EN 1514-1, tyyppi IBC SFS-EN 1514-1, type IBC
4) - -
1) Kuumasinkitty 2) Vaihtoehto irtolaipparakenteelle. 3)
Pintaksittely on keltapassivointi tai shksinkitys. 4) Tiivisteen
materiaali mritelln virtaavan aineen ja prosessiolosuhteiden
perusteella. 5) Materiaali vaatii erityisarvioinnin (PMA), katso
standardi PSK 4201. 6) Materiaalin valmistusmuoto (levy, tae jne.)
ja vastaava standardi mrtn tarvittaessa. 7) Osissa tai niiden
pakkauksissa tulee olla merkinnt, joiden perusteella osat voidaan
yhdist niit koskeviin ma-teriaalin valmistajan antamiin
materiaalitodistuksiin. 8) Kierteellisten putkenosien suurin
suositeltava nimelliskoko on enintn DN50. 1) Hot dip galvanized. 2)
Alternative to a collar + loose flange connection. 3) The surface
treatment is yellow passivation or hot-dip galvanizing. 4) The
gasket material is determined by the flowing fluid and process
conditions. 5) The material requires a particular material
appraisal (PMA), see standard PSK 4201. 6) Raw material (plate,
forging etc.) and respective standard shall be defined if
necessary. 7) The fittings or their packages must have markings, by
which the fittings can be connected to related material
certificates given by the supplier. 8) The maximum recommended size
for threaded pipe fittings is DN50.
-
PSK Standardisointi PSK 4255 E40H3A 10 (15) 5 PUTKILUOKAN
SALLITUT KYTTPAI-
NEET JA LMPTILAT
5 THE ALLOWABLE OPERATING PRES-SURES AND TEMPERATURES OF THE
PIPE CLASS
Putkiluokkaan kuuluvat osat on mitoitettu kest-mn 40 bar
ylipaine 20 C lmptilassa ja suurin sallittu lmptila on 250 C.
Alipaineen kesto 150 C lmptilassa on esitetty taulukossa 5.
The pipes and fittings belonging to this pipe class have been
designed to resist 40 bar overpressure in 20 C temperature and the
maximum allowable temperature is 250 C. Resistance of external
pressure in 150 C is shown in Table 5.
Putkiluokan paineenkestvyys (poikkeuksena istu-tettu haaroitus)
eri lmptiloissa on esitetty kuvas-sa 1.
The pressure resistance of the pipe class (except branch
connection) in different temperatures is given in Figure 1.
Istutetun kohtisuoran haaroituksen paineenkest-vyys eri
lmptiloissa saadaan kertomalla taulukon 4 arvo kuvasta 1 saatavan
sallitun paineen ja putki-luokan nimellispaineen (PN 40)
suhteella.
The pressure resistance of a perpendicular branch connection in
different temperatures is calculated by multiplying the value from
Table 4 with the ratio of the allowable pressure from Fig-ure 1 and
the nominal pressure (PN 40).
Putkiluokan alin sallittu kyttlmptila on -10 C, edellytten, ett
5.6 ruuvit tyttvt SFS-EN 13480-2 kohdan B.2.2.3 vaatimukset
(tarvitaan materiaalin erityisarviointi, PMA).
The lowest allowable operating temperature of the pipe class is
-10 C, presuming that bolts of strength class 5.6 meet the
requirements of SFS-EN 13480-2 clause B.2.2.3 (particular material
appraisal PMA is needed).
Mikli alin sallittu lmptila on alle -10 C, niin ma-teriaalit on
valittava siten, ett standardin SFS-EN 13480-2 Liitteen B
vaatimukset tyttyvt.
In case the lowest allowable temperature is below -10 C, the
materials must be chosen so that the requirements of standard
SFS-EN 13480-2, An-nex B, are met.
-
PSK Standardisointi PSK 4255 E40H3A 11 (15)
40,037,9
35,432,9
31,730,6
29,428,3 27,6 27,0
0,0
5,0
10,0
15,0
20,0
25,0
30,0
35,0
40,0
45,0
20 50 75 100 125 150 175 200 225 250 C
bar
Kuva 1 Sallitut paineet (bar) lmptilan funktiona Figure 1
Allowable pressures (bar) as a function of temperature Huomautus 1.
Vliarvot interpoloidaan lineaarisesti. Huomautus 2. Kyrn arvot on
saatu putken, putkenosien ja laippojen materiaalistandardeissa
kyseiseen lm-ptilaan annetun mytrajan perusteella lasketun
suunnittelujnnityksen ja vastaavan huoneenlmptilaan mritetyn
suunnittelujnnityksen suhdeluvuista. Nist suhdeluvuista pienin on
kerrottu putkiluokan nimellis-paineella (PN 40). Note 1.
Intermediate values are linearly interpolated. Note 2.The values of
the graph are calculated by the ratios of the design stress, based
on the proof strength value in the reference temperature from the
material standards of pipe, fittings and flange and respectively
the design stress in room temperature. The smallest value has been
multiplied by the nominal pressure (PN 40).
-
PSK Standardisointi PSK 4255 E40H3A 12 (15)
Taulukko 4 Istutetun haaroituksen (90) sallitut kyttpaineet
lmptilassa 20 C (bar) Table 4 Allowable operating pressures for
branch connection at 20 C (bar)
Runkoputki Header
Haaraputken ulkohalkaisija, mm Outside diameter of the branch
pipe, mm
Ulko-halkaisija Outside diameter
Seinmn-paksuus Wall thickness
17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3
219,1 273 323,9 355,6 406,4
D T Haaraputken seinmnpaksuus, mm Wall thickness of the branch
pipe, mm
mm mm 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 2,0 2,0 2,0 2,0 2,6 3,2
4,0 5,0 6,3
17,2 1,6 298,9
21,3 1,6 257,2 224,0
26,9 1,6 215,8 190,2 163,7
33,7 1,6 180,4 160,8 140,0 121,0
42,4 1,6 149,1 134,2 118,1 103,1 88,8
48,3 1,6 133,4 120,7 106,9 93,8 81,3 74,5
60,3 1,6 109,9 100,3 89,6 79,4 69,3 63,9 55,2
76,1 1,6 89,3 82,1 74,0 66,1 58,3 53,9 47,0 40,3
88,9 2,0 95,6 88,2 79,8 71,6 63,2 58,6 51,1 43,8 45,9
114,3 2,0 76,1 70,8 64,6 58,4 52,0 48,5 42,6 36,8 38,5 32,6
139,7 2,0 63,3 59,2 54,4 49,5 44,4 41,5 36,7 31,9 33,3 28,3
24,7
168,3 2,0 53,2 50,0 46,2 42,3 38,1 35,8 31,8 27,8 28,9 24,8 21,7
19,2
219,1 2,6 53,3 50,4 46,9 43,3 39,4 37,1 33,3 29,3 29,4 25,3 22,2
19,6 19,1
273 3,2 53,2 50,7 47,5 44,2 40,6 38,4 34,7 30,7 30,3 26,2 23,0
20,3 19,2 18,8
323,9 4,0 56,7 54,3 51,3 48,1 44,5 42,3 38,5 34,4 33,4 29,0 25,6
22,7 20,8 19,8 20,2
355,6 5,0 65,3 62,8 59,6 56,2 52,3 49,9 45,7 41,1 39,5 34,5 30,6
27,2 24,4 22,6 22,4 24,1
406,4 6,3 73,1 70,7 67,5 64,0 60,0 57,5 53,1 48,2 46,1 40,6 36,2
32,3 28,6 26,0 25,1 26,2 27,6
Haaroituksen kulma on 90+5. Haaroituksen molempien putkien on
oltava tmn putkiluokan mukaisia. Haaraputken istutus voidaan tehd
pputken pintaan tai pputkessa olevaan aukkoon. Taulukon arvot on
laskettu siten, ett liitettvien putkien pituushitsin lujuuskerroin
z=1,0. The angle of the branch connection is 90+5. Both pipes of
the branch connection must be according to this pipe class. The
branch connection can be made as set-on or set-in. Values have been
calculated assuming the longitudinal weld joint factor z=1,0 for
both connected pipes.
Huom: Harmaalla merkityt istutukset eivt kest putki-luokan
nimellispainetta 40,0 bar. Note: Branch connections marked with
grey back-ground do not have a full resistance for nominal
pres-sure 40,0 bar of the pipe class.
-
PSK Standardisointi PSK 4255 E40H3A 13 (15) Taulukko 5 Suurin
alipaine (bar) laskentalmptilassa 150 C Table 5 Allowable external
pressure (bar) in calculation temperature 150 C
Nimellis-koko
Nominal size
Ulko-halkaisija
Outer diameter
Seinmn-paksuus
Wall thickness
Putken jykistejako
Pitch of stiffening rings
Jykisteen 2) mitat Stiffening ring 2) dimensions
Alipaineen kesto Allowable external pressure
DN D T L hS ew pmax (bar)
10 17,2 1,6 - - - 1) 15 21,3 1,6 - - - 1) 20 26,9 1,6 - - - 1)
25 33,7 1,6 - - - 1) 32 42,4 1,6 - - - 1) 40 48,3 1,6 - - - 1) 50
60,3 1,6 - - - 1) 65 76,1 1,6 - - - 1) 80 88,9 2 - - - 1) 100 114,3
2 - - - 1) 125 139,7 2 - - - 1) 150 168,3 2 - - - 1) 200 219,1 2,6
- - - 1) 250 273 3,2 - - - 1) 300 323,9 4 - - - 1) 350 355,6 5 - -
- 1) 400 406,4 6,3 - - - 1)
1) Tss nimelliskoossa putkiluokalle E40H3A sallitaan 1 bar
alipaine. 2) Tss putkiluokassa jykisterenkaita ei kytet. 1) For
this nominal size in pipe class E40H3A a vacuum (i.e. 1,0 bar
external pressure) is allowed. 2) In this pipe class stiffening
rings are not used.
-
PSK Standardisointi PSK 4255 E40H3A 14 (15) OPASTAVIA
TIETOJA
INFORMATION FOR GUIDANCE
O.1 Laskentaperusteet
O.1 Calculation criteria
Yleiset laskentaperusteet putkiluokan osille: mitoitus SFS-EN
13480-3 mukaan ylipaine 4,0 MPa ja lmptila 20 C alipaine 0,1 MPa ja
lmptila 150 C suunnittelujnnitys f = 291 MPa (ylipaine) mytlujuus
Rp0,2 = 335 MPa (alipaine) korroosiovara c0 = 0,0 mm
hitsausliitoksen lujuuskerroin z = 1,0 DN < 400
General calculation criteria for piping components of the pipe
class dimensioning in accordance with SFS-EN
13480-3 overpressure 4,0 MPa, temperature 20 C external pressure
0,1 MPa, temperature 150 C design stress f = 291 MPa (overpressure)
proof strength Rp0,2 = 335 MPa (external pres-
sure) corrosion allowance c0 = 0,0 mm weld joint factor z = 1,0
DN < 400
Osien seinmnpaksuuksille on kytetty seuraavia
valmistustoleransseja: putket
- 10 % tai vhintn 0,2 mm, kun DN < 400 kyrt, kartiot,
T-putket ja pdyt
- 12,5 %, kun DN < 400
The following manufacturing tolerances have been used for the
wall thickness of various components: pipes - 10 % or at least 0,2
mm, when DN < 400 elbows, reducers, tees and caps - 12,5 %, when
DN < 400
Kartioiden laskenta on tehty epkeskeisille levykar-tioille.
The calculation of reducers has been done for ec-centric
reducers.
O.2 Nimikkeen muodostaminen
O.2 Forming of designation
Esimerkkej nimikkeen muodostamisesta: Putki 168,3x2,0 - SFS-EN
10217-7 - TC 1 - W1
- 1.4462 Kyr 168,3x2,6 - SFS-EN 10253-4 - tyyppi A -
3D - 90o - 1.4462 Kartio E1) 219,1x3,2 168,3x3,2 - SFS-EN
10253-4 - tyyppi A Taul. A.6 - 1.4462 T-putki 219,1x6,3
168,3x5,0 - SFS-EN
10253-4 - tyyppi A Taul. A.4 - 1.4462 Irtolaippa SFS-EN 1092-1 -
tyyppi 02 DN 400
PN 40 - P265GH - SFS-EN 10028-2 Kaulus SFS-EN 1092-1 - tyyppi 35
DN 200
PN 40 - 1.4462 Kauluslaippa SFS-EN 1092-1 - tyyppi 11 - B1
DN 50 PN 40 - 1.4462 - EN 10222-5 Umpilaippa SFS-EN 1092-1 -
tyyppi 05
DN 400 PN 40 - P265GH - SFS-EN 10028-2 Pty 219,1x2,6 - SFS-EN
10253-4 - tyyppi A -
1.4462 Tiiviste DN 100 - PN 40 - tyyppi IBC - 2 mm -
SFS-EN 1514-1 2)
Examples of designations: Pipe 168,3x2,0 - SFS-EN 10217-7 - TC 1
- W1
- 1.4462 Elbow 168,3x2,6 SFS-EN 10253-4 - type A -
3D - 90o - 1.4462 Reducer E1) 219,1x3,2 168,3x3,2 - SFS-EN
10253-4 - type A Table A.6 - 1.4462 Tee 219,1x6,3 168,3x5,0 -
SFS-EN 10253-4 -
type A Table A.4 - 1.4462 Loose flange SFS-EN 1092-1 - type 02
DN
400 PN 40 - P265GH - SFS-EN 10028-2 Collar SFS-EN 1092-1 - type
35 DN 200
PN 40 - 1.4462 Welding neck flange SFS-EN 1092-1 - type 11 -
B1 DN 50 PN 40 - 1.4462 - EN 10222-5 Blind flange SFS-EN 1092-1
- type 05 DN
400 PN 40 - P265GH - SFS-EN 10028-2 Cap 219,1x2,6 - SFS-EN
10253-4 - type A -
1.4462 Gasket DN 100 PN 40 - type IBC - 2 mm -
SFS-EN 1514-12)
1) E = epkeskeinen, K = keskeinen 2) Tiivistemateriaalin valinta
mrytyy virtaavan aineen ja prosessiolosuhteiden mukaan.
1) E = eccentric, K = concentric 2) Selection of the gasket
material shall be deter-mined by the fluid and process
conditions.
-
PSK Standardisointi PSK 4255 E40H3A 15 (15) O.3 Putkiluokan
tunnus
O.3 Identification of the pipe class
Putkiluokan tunnuksen alussa oleva E-kirjain osoit-taa, ett
putkiluokka noudattaa yhdenmukaistettuja eurooppalaisia standardeja
ja se on olennainen osa putkiluokan merkint.
The letter E in the beginning of the identification of the pipe
class indicates that the pipe class complies with the harmonized
European standards and it is an integral part of the pipe class
identification.
Putkiluokalle annetaan eri tunnus, jos sen sislt poikkeaa tss
standardissa esitetyst.
A different identification shall be given to the pipe class if
the contents deviate from this standard.