Promag 10D

Products Solutions Services

Application / FunctionOverview Technical data Dimensions

Electrical connection Price table ContactGo to shop

Technical DatasheetTD 00061E/24/EN/01.13

• Simple installation and commissioning

•High degree of accuracy and measuring stability

• Cost-effective flow measurement•No pressure loss, thus

energy-saving•Not sensitive to vibrations

Complete product information:www.e-direct.us/promag10d

Specs at a glance:

•Flow measurement: up to 10 m/s (26.4 gal/min)

•Minimum conductivity: ≥ 50 µS/cm

•Fluid temperature: up to +60 °C (140 °F)

•Lining material: Polyamide •Process pressure:

up to 16 bar (870 psi)

Electromagnetic flow measuring system

ProlinePromag10D

$ 2401.00

Proline Promag 10D for inflow measurement

ProlinePromag10D 2

Overview Technical data Dimensions

Electrical connection Price table ContactGo to shop

Application / Function

Application Proline Promag 10D is an electromagnetic flowmeter for bidirectional measurement of conductive liquids. It is used for flow measurements in water or service water applications. Due to its easy installation and operation, its robust design and low price it can be used in applications where only limited principles could be used before. Drinking water approvals according to KTW/W270, WRAS BS 6920, ACS and NSF 61 are available.

ApplicationexampleFunction Following Faraday's law of magnetic induction, a voltage is induced in a conductor moving through a magnetic field. In the electromagnetic measuring principle, the flowing fluid is the moving conductor. By measuring the induced voltage, the flow velocity of the medium can be measured. The flow volume is calculated by means of the pipe cross-section area.

ProlinePromag10D 3

Application / FunctionOverview Dimensions

Electrical connection Price table ContactGo to shop

Technical data

InputMeasuring ranges Typically v = 0.01 to 10 m/s

(0.033 to 33 ft/s) with the specified accuracy

Output signalCurrent output Active: 4 to 20 mA, RL < 700 Ω

(for HART®: ≥ 250 Ω)Pulse/status output Passive: 30 V DC/250 mA; Open Collector

Power supplySupply voltage 85 to 250 V AC, 45 to 65 Hz;

20 to 28 V AC, 45 to 65 Hz;11 to 40 V DC

Power consumption (incl. sensor)

85 to 250 V AC: < 12 VA;20 to 28 V AC: < 8 VA;11 to 40 V DC: < 6 W

AccuracyReference operating conditions

as per DIN EN 29104 and VDI/VDE 2641

Fluid temperature +28 °C ±2 K (+82 °F ± 2 K)Ambient temperature +22 °C ±2 K (+72 °F ± 2 K)Warm-up period 30 minutesMaximum measured error (Current output)

±0.5% of full scale value add. typically ±5 μA

Maximum measured error (Pulse output)

±0.5% of reading ±2 mm/s

Repeatability Max. ±0.2% o.r. ±2 mm/s (o.r. = of reading)

Inlet and outlet runIf possible, install the sensor well clear of assemblies such as valves, T-pieces, elbows, etc.Inlet run 5×DNOutlet run ≥ 2×DN

Operating conditions: EnvironmentAmbient temperature –20 to +60 °C (–4 to +140 °F)Storage temperature –20 to +60 °C (–4 to +140 °F)Degree of protection IP 67 (NEMA 4X) for transmitter and sensorShock and vibration resistance

Acceleration up to 2 g followingIEC 600 68-2-6

EMC As per IEC/EN 61326 and NAMUR Recommendation NE 21; Emission: to limit value for industry EN 55011

Operating conditions: Process

Medium temperature 0 to +60 °C (32 to 140 °F)Minimum conductivity

≥ 50 μS/cm

Medium pressure PN16Pressure tightness Measuring tube: 0 mbar abs (0 psi abs) with

a fluid temperature of ≤ 60 °C (≤ 140 °F)

MaterialGround disks 1.4301/304Sensor housing powder-coated die-cast aluminumMeasuring tube polyamide, O-rings: EPDMElectrodes 1.4435/316LFitted electrodes Two electrodes made of 1.4435/316L

Mounting kitIncludedConsists of mounting bolts, seals, nuts and washers

Human interfaceDisplay elements Liquid crystal display: unilluminated,

two-line, 16 characters per lineDisplay Display (operating mode) preconfigured:

volume flow and totalizer statusOperating elements Local operation via three keysRemote operation Operation via HART® protocol and FieldCare

ApprovalsDrinking water approval WRAS BS 6920

Technicaldata

0 1

2.5

[%]

2.0

1.5

1.0

0.5

0 v [m/s]

0.5 %

Fluctuations in the supply voltage do not have any effect within the specified range. Max. measured error in % of reading

Maximummeasurederror

ProlinePromag10D 4

Application / FunctionOverview

Electrical connection Price table ContactGo to shop

DimensionsTechnical data

Dimensions(ininches)Flowcharacteristicvalues

5.90

4.76

6.34 to 7.13

0.79 to 1.81

L

B

A

C

7.0

Installation according to instruction manual.

DN L A B C WeightEN (DIN)/JIS [mm]

ANSI[inch]

[inch] [inch] [inch] [inch] [lbs]

25 1" 2.17 11.1 9.45 1.69 6.440 1 ½" 2.72 11.9 9.88 2.05 7.750 2" 3.27 12.8 10.3 2.44 9.565 - (93

mm)(342 mm)

(272 mm)

(70 mm)

5.1

80 3" 4.61 13.8 10.9 2.95 13.5100 4" 5.83 14.9 11.4 3.50 19.4

Diameter Recommended flow Factory settings

[mm] [inches] min./max. fullscale value(v ~ 0.3 or 10 m/s)

Full scale valuecurrent output(v ~ 2.5 m/s)

Pulse value(~ 2 Pulse/s)

Low flow cut off(v ~ 0.04 m/s)

25 1” 2.5 to 80 gal/min 18 gal/min 0.20 gal 0.25 gal/min40 1 ½” 7 to 190 gal/min 50 gal/min 0.50 gal 0.75 gal/min50 2” 10 to 300 gal/min 75 gal/min 0.50 gal 1.25 gal/min65 - 16 to 500 gal/min 130 gal/min 1.00 gal 2 gal/min80 3” 24 to 800 gal/min 200 gal/min 2.00 gal 2.5 gal/min100 4” 40 to 1250 gal/min 300 gal/min 2.00 gal 4 gal/min

ProlinePromag10D 5

Application / FunctionOverview Technical data Dimensions

ContactGo to shopElectrical connection Price table

Pricetable

Moreproductstocompleteyourmeasuringpoint…

Electromagnetic flowmeter Promag 10D Order no. Price/pcs. in USDPower Supply; Display Diameter 1 to 5 6 to 10 11 to 3585-250 V AC2-line, push buttons

DN25 10D25-5CGA1AA0A4AA+M1 2728.00 2537.00 2401.00DN40 10D40-5CGA1AA0A4AA+M1 2728.00 2537.00 2401.00DN50 10D50-5CGA1AA0A4AA+M1 2728.00 2537.00 2401.00DN65 10D65-5CGA1AA0A4AA+M1 2954.00 2747.00 2600.00DN80 10D80-5CGA1AA0A4AA+M1 2954.00 2747.00 2600.00DN100 10D1H-5CGA1AA0A4AA+M1 3148.00 2928.00 2770.00

20-28 V AC / 11-40VDC2-line, push buttons

DN25 10D25-5CGA1AA0A5AA+M1 2728.00 2537.00 2401.00DN40 10D40-5CGA1AA0A5AA+M1 2728.00 2537.00 2401.00DN50 10D50-5CGA1AA0A5AA+M1 2728.00 2537.00 2401.00DN65 10D65-5CGA1AA0A5AA+M1 2954.00 2747.00 2600.00DN80 10D80-5CGA1AA0A5AA+M1 2954.00 2747.00 2600.00DN100 10D1H-5CGA1AA0A5AA+M1 3148.00 2928.00 2770.00

Prices valid until 09.30.2013 in U.S. dollars per unit (not including shipping and applicable sales tax).See Endress+Hauser, Inc. Terms and Conditions of Sale for shipping, tax, and payment terms.

Complete product information:www.e-direct.us/promag10d

Electricalconnection

b

a

e

2127–

25–

26+

24+ L1

(L+)N

(L-)

e

g

b

d

hi

cf

CapacitiveprobeLiquicap T FMI21

PaperlessrecorderEcograph T RSG30

Connecting the transmitter, cable cross-section max. 2.5 mm²a Electronics compartment coverb Power supply cablec Ground terminal for protective groundd Terminal connector for power supply cablee Signal cablef Ground terminal for signal cableg Terminal connector for signal cableh Service connectori Ground terminal for potential equalization

Terminal No.:• 24 (+)/25 (-) = Pulse/status output• 26 (+)/27 (-) = HART® current outputFunctional values see "Output signal"

• 1 (L1/L+)/2 (N/L–) = Power supplyFunctional values see "Supply voltage"

PressuretransmitterCerabar T PMC131

Application / FunctionOverview Technical data Dimensions

Electrical connection Price table ContactGo to shop

Contact

E-directEndress+Hauser, Inc.2350 Endress PlaceGreenwood, IN 46143

Direct order

Internet www.e-direct.usby phone 888- EH-DIRECT

(343-4732)per Fax 317-535-8498E-Mail [email protected]