-
CODE : 00Z
CONTENTS
Parts marked with "!" are important for maintaining the safety
of the set. Be sure to replace these parts with specifiedones for
maintaining the safety and performance of the set.
This document has been published to be usedfor after sales
service only.The contents are subject to change without notice.
PROGRAMMING MANUAL
LEAD-FREE SOLDER MODEL
XEA21SUPME
ELECTRONICCASH REGISTER
MODEL XE-A21S
■ LEAD-FREE SOLDER
CHAPTER 1. MASTER RESET AND PROGRAM RESET . . . . . . 1 - 1
CHAPTER 2. PROGRAM MODE . . . . . . . . . . . . . . . . . . . .
. . . . . . 2 - 1
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE. . . . . . . . . . . . . .
. . . . 3 - 1
-
XE-A21S LEAD-FREE SOLDER
■ LEAD-FREE SOLDERThe PWB’s of this model employs lead-free
solder. The “LF” marks indicated on the PWB’s and the Service
Manual mean “Lead-Free” solder. Thealphabet following the “LF” mark
shows the kind of lead-free solder.
Example:
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder
thread. Never use conventional lead solder thread, which may cause
a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C
higher than that of conventional lead solder thread, the use of the
exclusive-use soldering iron is rec-ommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C,
which is about 40°C higher than that of conventional lead solder,
and its soldering capacity is inferior toconventional one, it is
apt to keep the soldering iron in contact with the PWB for longer
time. This may cause land separation or may exceed the
heat-resistive tem-perature of components. Use enough care to
separate the soldering iron from the PWB when completion of
soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the
iron tip may corrode easily. Turn ON/OFF the soldering iron power
frequently.
If different-kind solder remains on the soldering iron tip, it
is melted together with lead-free solder. To avoid this, clean the
soldering iron tip after com-pletion of soldering work. If the
soldering iron tip is discolored black during soldering work,
cleanand file the tip with steel wool or a fine filer.
5mm
Lead-Free
Solder composition code (Refer to the table at the right.)
Solder composition
Sn-Ag-Cu
Sn-Ag-BiSn-Ag-Bi-Cu
Sn-Zn-Bi
Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
Bi-Sn-Ag-PBi-Sn-Ag
a
b
z
i
n
s
p
Solder composition code
a
-
XE-A21S MASTER RESET and program reset
1 – 1
CHAPTER 1. MASTER RESET AND PROGRAM RESET
1. MASTER RESETTING
Master resetting clears the entire memory and resumes initial
values.
Master resetting can be accomplished by using the following
procedure:
Procedure :
1) Unplug the AC cord from the wall outlet, or set the mode
switch to OFF position.
2) Let the ECR be without the memory backup battery.
3) Wait over 1 minute for discharging.
4) Set the mode switch to any position except OFF.
5) Plugin the AC cord to the wall outlet, or turn the mode
switch from OFF position to another position.
The master reset can also be accomplished in the following
case.
In case power failure occurs when the machine has no battery
attached to it, the master reset operation is automatically
performed after the powerhas been restored.
(This is because if power failure occurs with no battery
attached to the machine, all the memories are lost and the machine
does not work properlyafter power recovery; this requires the
master reset operation.)
2. PROGRAM RESETTING (INITIALIZATION)
This resetting resumes the initial program without clearing
memory.
This resetting can be operated at below sequence in PGM
mode.
Procedure:
1) Unplug the AC cord from the wall outlet.
2) Wait over 1 minute for discharging.
3) Set the mode switch to the PGM position.
4) While holding down the FEED key, plugin the AC cord to the
wall outlet.
Note: In case power failure occurs when the machine has no
battery attached to it, the master reset operation is automatically
performed after thepower has been restored.
-
CHAPTER 2. PROGRAM MODE
1. READING STORED PROGRAMS
The machine allows you to read every program stored in the PGM
mode.
■ Key sequence for reading stored program
(*1)PLU code range can be specified by entering the start and
end numbers according to the following procedure.When specifying a
single time interval, PLU code, the start number has only to be
entered.
■ SAMPLE PRINTOUTS
1. Programming report 1
Report name Key sequence
Programming report 1
Programming report 2 2 3
[Auto] key programming report 1 3
Printer density programming report 3 3
PLU programming report (*1)
CA/AT
CA/AT
CA/AT
CA/AT
Start PLU code @/FOR End PLU code PLU
: VARIOUS PROGRAM Refer to the programming section about the
data of each JOB.
HEADER
*PGM*MODE TITLE
F01 ( - ) xx 007
-1000.00F02 % 1xxxx 000L100.00% -10.00%F04
NET1F05F06F07F08F09
F25F26F27F28
TAX1 ST
::
::
F40F41F42F43
::
:F67 COPYF68 EJF69 EJ END
SHARP
SHARPPRESENTS THE
BEST ECR
ISTHE BEST
#5 000000000000000000000000
00000000
#6#7#10 0000#11 0#15#19 00#35 007#50 007T 1 10.0000%
T2 4.0000%
05/02/2006 12:34PM
123456#1234
D99 T1234 071
T1234
DPT.99 0.00
GRS TAX1RFD TAX1TAX1TX1 EXPT
GRS MTAXRFD MTAXM-TAX 7GST EXPT
***RAxxx 9***POxxx 9TRANS CT NET3
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. / CLERK NAME
D01 T1234 073DEPT CODE/TAXABLE/ PROGRAM (*1)
DPT.01xxxxxx -1234.56
D02 T1234 073DPT.02 -1234.56
TEXT/PRICE WITH SIGN
(MAX department is decided by PGM selection.)
FUNCTION NO. /TEXT /HALO
FUNCTION NO. /TEXT /HALO
FUNCTION NO. /TEXT/PROGRAM (*2)
AMOUNT WITH SIGN
FUNCTION NO. /TEXT /PROGRAM (*2) HALO WITHOUT SIGN/ RATE WITH
SIGN
FUNCTION NO./TEXT
F 44 CASH FUNCTION NO. /TEXT 008
F 45 CHECKxxx008
F 46 CHRAGExx008
F 47 CHARGE-F 48 CONV 1 00
F 49 CONV 2F 50 ****CID
AAAA 9999.9999
(JOB# 5) FUNCTION SELECT(JOB# 6) PRINT FUNCTION(JOB# 7) RECEIPT
PRINT FORMAT(JOB#10) POWER SAVING PROGRAMMING(JOB#11) LOGO
FORMAT(JOB#15) FUNCTION SELECT2 (JOB#19) DOUGHNUT TAX EXEMPT
(JOB#35) ONLINE Timeout time (JOB#50) Thermal printer densityTAX1
RATE
/ 1.001 0.112 0.233 0.574 0.785 1.11
/PROGRAM (*3)
FUNCTION NO. /TEXT/PROGRAM (*4) CURRENCY SYMBOL/RATE
CYCLE TAX /BREAK POINT AMOUNT
0.10
LOGO TEXT
FUNCTION NO. /TEXT
(It is according with LOGOFORMAT.)
TAX2 RATE LOWER TAX LIMIT
FUNCTION NO. /TEXT /PROGRAM (*3)
FUNCTION NO. /TEXT /PROGRAM (*3)
T3 5.0000%0.20
TAX3
T4 ------ TAX4 ("------": INHIBIT)C#01 CLERK.01C#02 CLERK.02
C#25 CLERK.25
Clerk No. /Clerk name
: :
BETTY___
01
XE-A21S PROGRAM MODE
2 – 1
-
(*1) DEPT PROGRAM : ABC
(*2) (-)/[%] PROGRAM : ABC
(*3) MEDIA PROGRAM : ABC
(*4) CONVERSION PROGRAM : AB
2. Programming report 2
3. [Auto] key programming report
4. Printer density report
A: REGISTRATION TYPE A
NORMAL 0
SICS 1
B: LIMITATION DIGITS (*2) = 0 to 7
C: AMOUNT ENTRY TYPE C
Inhibited 0
Open 1
Preset 2
Open and Preset 3
A: ENTRY FOR ITEM A
ENABLE 0
DISABLE 1
B: ENTRY FOR SBTL B
ENABLE 0
DISABLE 1
C: LIMITATION DIGITS (for (-) key) = 0 to 7 (0 FIXED for
[%n])
A: Footer print on Receipt A
No 0
Yes 1
B: Entry of amount tendered B
Non compulsory (Cash, check), Inhibit (Credit)
0
Compulsory 1
C: LIMITATION DIGITS (0=INHIBIT) = 0 to 8
A: OPEN RATE ENTRY A
ENABLE 0
DISABLE 1
B: PRESET RATE ENTRY B
ENABLE 0
DISABLE 1
: OTHERS PROGRAM Refer to the programming section about the data
of each JOB.
GT2
HEADER
*PGM*MODE TITLE
05/02/2006 12:34PM
123456#1234
DATE/TIME/CLERK NO
MACHINE NO./CC-NO./ CLERK NAME
#61 00000000 (JOB#61) OTHERS1 #62 00000000 (JOB#62) OTHERS2#63
00000000 (JOB#63) OTHERS3 #64 00000000 (JOB#64) OTHERS4 #65
00000000 (JOB#65) OTHERS5 #66 00000000 (JOB#66) OTHERS6 #67
00000000 (JOB#67) OTHERS7 #68 00000000 (JOB#68) OTHERS8 #69
00000000 (JOB#69) OTHERS9 #70 00000000 (JOB#70) OTHERS10 #71 GT2
#72
#76 Z1 0000 GENERAL Z1 RESET COUNTER #77 Z2 0000 GENERAL Z2
RESET COUNTER#85 ___$ DOMESTIC CURRENCY SYMBOL#86 00 TRAINING CLERK
#87 TRAINING TRAINING MODE TEXT#88 0 LANGUAGE MODE
(For the fixed messages) #90 0
EJ/PLU MEMORY TYPE(0: TYPE, 1: TYPE2)
#95 99
MAX NUBMER OF DEPT
$00000000000.00
GT3GT3 $00000000000.00
01
BETTY___
HEADER
*PGM* MODE TITLE
KEY TEXT
05/02/2006 12:34PM
123456#1234
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. / CLERK NAME
#01 1000CASH
DELETE (NO KEY)------
01
BETTY___
HEADER
*PGM* MODE TITLE
05/02/2006 12:34PM
123456#1234
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. / CLERK NAME
#01 5010 : 0123456789AB20 : 0123456789AB30 : 0123456789AB40 :
0123456789AB50 : 0123456789AB60 : 0123456789AB70 : 0123456789AB80 :
0123456789AB90 : 0123456789AB
Printing Sample (Light & Shade value between 10 to 90.)
Thermal printer density
01
BETTY___
XE-A21S PROGRAM MODE
2 – 2
-
5. PLU data report
(*1) PROGRAM : Y
2. USER PROGRAMMING
1) PRICE PROGRAMMING FOR [DEPT.] & (-) KEYS
If a price is set for a department which amount entry type is
“INHIBIT” or“OPEN”, its amount entry type is set as below
automatically.
MRS = 0
2) DEPT FUNCTION PROGRAMMING
Y: PROGRAM Y
SUBDEPT 0
PLU 1
YY: Department Code (01 to 99)
XXXXXX: Unit price (Max. 6digits)
“PRESET” 1 “INHIBIT”
“OPEN & PRESET” 1 “OPEN”
HEADER
*PGM*MODE TITLE
05/02/2006 12:34PM
123456#1234
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
P001PLU001xxxxxx
0001-12001
P001 ----
-1234.56
TEXT/PRICE WITH SIGN
START CODE/ END CODE (RANGE DATA)
::
NOTE : The deleted PLU is not printed.
PLU CODE/Associated DEPT code/Type (*1)
01
BETTY___
When PLU is deleted at the programming JOB.
XXXXXX
YY XXXXXX
0
0
CA/ATDPTn
DPTnDEPT SHIFT
DEPT# SBTL
(-)
YY: Department code (01 to 99)
A: Taxable 4 A
No 0 ★
Yes 1
B: Taxable 3 B
No 0 ★
Yes 1
C: Taxable 2 C
No 0 ★
Yes 1
D: Taxable 1 D
No 0
Yes 1 ★
E: REGISTRATION TYPE A
NORMAL 0 ★
SICS 1
F: SIGN B
+ 0 ★
- 1
G: LIMITATION DIGITS = 0 to 7
0 : OPEN PRICE REGISTRATION INHIBIT.
H: AMOUNT ENTRY TYPE D
Inhibited 0
Open 1 ★
Preset 2
Open & Preset 3
MRS = 00010071(TAXABLE 1, NORMAL, SIGN (+), HALO = 7, OPEN)
ABCDEFGH
ABCDEFGHYY
0
0
DPTn@/FOR
@/FORDEPT#
CA/AT
DPTnDEPT SHIFT
XE-A21S PROGRAM MODE
2 – 3
-
3) (-) & [%] KEY FUNCTION PROGRAMMING
4) RATE PROGRAMMING FOR [%] ANDCONVERSION KEY.
The DECIMAL POINT must be entered for setting the decimal
digits.
5) PROGRAMMING FOR CONVERSION
MRS = 00
6) PROGRAMMING FOR FUNCTION KEYS
MRS = 7 (Manual TAX), 9 (RA, PO)
7) PROGRAMMING FOR MEDIA KEYS
([#/ST] key is used for programming of CASH.)
MRS = 008
A: Taxable 4 A
No 0 ★
Yes 1
B: Taxable 3 B
No 0 ★
Yes 1
C: Taxable 2 C
No 0 ★
Yes 1
D: Taxable 1 D
No 0 ★
Yes 1
E: SIGN E
+ 0
- 1 ★
F: ENTRY FOR ITEM F
ENABLE 0 ★
DISABLE 1
G: ENTRY FOR SBTL G
ENABLE 0 ★
DISABLE 1
H: LIMITATION DIGITS (for (-) key) = 0 to 7
0 : OPEN PRICE REGISTRATION INHIBIT (for (-) KEY)
0 : FIXED for [%]
MRS = 00001007(NON-TAXABLE, MINUS SIGN, ITEM&SBTL, HALO =
7)
(RATE): XXX.XX: Rate for % (0.00 to 100.00)
XXXX.XXXX: Rate for CONVERSION (0.0000 to 9999.9999)
MRS = 0.00 (%n)
0.0000 (CONVERSION)
(-)
%n
0
ABCDEFGH CA/AT@/FOR
0
(RATE) CA/AT%n
CONV
A: OPEN RATE ENTRY A
ENABLE 0 ★
DISABLE 1
B: PRESET RATE ENTRY B
ENABLE 0 ★
DISABLE 1
A: LIMITATION DIGITS (0 = INHIBIT)
= 0 to 7 (for Manual TAX)
= 0 to 9 (for RA, PO)
A: Footer print on Receipt A
No 0 ★
Yes 1
(0 FIXED for RA/PO)
B: Entry of amount tendered B
Non compulsory (Cash, Check), Inhibit (Credit) 0 ★
Compulsory 1
(0 FIXED for RA/PO)
C: LIMITATION DIGITS (0=INHIBIT) = 0 to 8
CONV
0
AB CA/AT@/FOR
0
A CA/ATPO@/FOR
RA
TAX
(for Manual-TAX)
ABC @/FOR CH
CHK
#/ST
(for CASH)
0
CA/AT
XE-A21S PROGRAM MODE
2 – 4
-
8) DATA PROGRAMMING FOR PLUThere are programmed by below key
sequence.The PLU code is increment automatically when one
programming dataof a PLU is set.And it is operated continuously
until depressing the [CA/AT] key.The JOB is automatically finalized
when a maximum PLU code is programmed.
(Basic programming sequence)
Basic operation consists of below 2 kinds.
9) PROGRAMMING OF DEPARTMENTS TO BEASSOCIATED WITH PRICE
PRESET
DELETE means to be set as a inhibited PLU in memory.When it is
assigned some DEPT for the inhibited (deleted) PLU,the PLU is set
the MRS value except its price.
10) PROGRAMMING OF PLU/SUBDEPT
11) PROGRAMMING OF DEPARTMENT TEXT
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTER BY NUMERIC KEYS IS AS FOLLOWS:
MRS = DEPT. xx (xx: DEPT Code)
12) PROGRAMMING OF PLU TEXT
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:
MRS = PLU.xxxx (xxxx: PLU code)
13) PROGRAMMING OF FUNCTION TEXT
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:
MRS = Refer to the following table
XXXX: PLU CODE (1 to 1200)
ZZ: DEPT CODE (1 to 99)
YYYYYY: UNIT PRICE (6 digits)
MRS = DEPT1, Price: 0 (Create: PLU001 to PLU1200)
XXXX: PLU CODE (1 to 1200)
Y: 0 = SUBDEPT, 1 = PLU
MRS = 1 (PLU type)
(DATA)
(Code increment)
(Code entry)
PLU DPTn CA/ATXXXXPLU CODE
SBTL(DATA)DEPT#DEPT CODE
DEPT SHIFT DPTn
(DATA)
(Code increment)
(Code entry)
PLU SBTL CA/ATXXXX
PLU CODE
YYYYYY
(Code increment)
(Code entry)
PLU DPTn
DPTn
CA/ATXXXXPLU CODE
SBTLYYYYYYDEPT#DEPT CODE
0
ZZ
0
PLU DELETE (INHIBIT)
DEPT SHIFT
Y
(Code entry)
PLU SBTL CA/ATXXXX
PLU CODE
0
XX: Department Code (1 to 99)
(CHATACTERS): CHARCTER (Max. 12 Characters)
YYY 3 [00] KEY
YYY: CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
XXXX: PLU CODE (1 to 1200)
(CHARACTERS): CHARACTER (Max. 12 Characters)
YYY3 [00] KEY
YYY: CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
XX: FUNCTION CODE (Refer to the FUNCTION LIST)
(CHARACTERS): CHARACTER (Max. 8 Characters)
YYY 3 [00] KEY
YYY: CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
DPTn (CHARACTERS)
XX
SBTL SBTL 1 CA/TA
DEPT#DEPT CODE
NO CHANGE
DPTnDEPT SHIFT
PLU (CHARACTERS)
NO CHANGE
(Code increment)
(Code entry)
XXXXSBTL SBTL2 CA/ATPLU CODE
(CHARACTERS)
NO CHANGE
XXSBTL @/FOR SBTL3 CA/AT
XE-A21S PROGRAM MODE
2 – 5
-
■ FUNCTION LIST
14) PROGRAMMING OF LOGO TEXT
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:
(Sample)
F-NO. FUNCTIONDEFAULT12345678
1 (-) (-)
2 %1 %1
3 %2 %2
4 NET1 NET1
5 TAXABLE1 ST TAX1 ST
6 GROSS TAX1 GRS TAX1
7 REFUND TAX1 RFD TAX1
8 NET TAX1 TAX1
9 EXEMPT TAX1 TX1 EXPT
10 TAXABLE2 ST TAX2 ST
11 GROSS TAX2 GRS TAX2
12 REFUND TAX2 RFD TAX2
13 NET TAX2 TAX2
14 EXEMPT TAX2 TX2 EXPT
15 TAXABLE3 ST TAX3 ST
16 GROSS TAX3 GRS TAX3
17 REFUND TAX3 RFD TAX3
18 NET TAX3 TAX3
19 EXEMPT TAX3 TX3 EXPT
20 TAXABLE4 ST TAX4 ST
21 GROSS TAX4 GRS TAX4
22 REFUND TAX4 RFD TAX4
23 NET TAX4 TAX4
24 EXEMPT TAX4 TX4 EXPT
25 GROSS M-TAX GRS MTAX
26 REFUND M-TAX RFD MTAX
27 NET M-TAX M-TAX
28 NON GST SUBTOTAL GST EXPT
29 PST TOTAL PST TTL
30 GST TOTAL GST TTL
31 TOTAL TAX TTL TAX
32 NET without TAX NET
33 NET2 NET2
34 REFUND REFUND
35 VOID VOID
36 VOID MODE VO I D
37 MANAGER VOID MGR VD
38 SBTL VOID SBTL VD
39 NO SALE NO S ALE
40 RA ***RA
41 PO ***PO
42 CUSTOMER TRANS CT
43 NET3 (SALES) NET3
44 CASH CASH
45 CHECK CHECK
46 GROSS CHARGE1 CHARGE
47 REFUND CHARGE1 CHARGE-
48 CONVERSION (PRESET RATE) CONV 1
49 CONVERSION (OPEN RATE) CONV 2
50 CASH IN DRAWER ****C ID
51 CASH+CHECK IN DRAWER CA+CH ID
52 CHECK CHANGE CHK /CG
53 VAT EXEMPT (For DOUGHNUT TAX Type1) VAT EXPT
54 (+) DEPT TOTAL *DEPT TL
55 (-) DEPT TOTAL DEPT ( - )
56 SUBTOTAL SUBTOTAL
57 MDS SBTL MDSE ST
58 TOTAL ***TOTAL
59 CHANGE CHANGE
60 ITEMS ITEMS
61 DEPT. REPO. TITLE DEPT
62 PLU REPO. TITLE PLU
63 TRANS. REPO. TITLE TRANS.
64 CLERK REPO. TITLE CLERK
65 HOURLY REPO. TITLE HOURLY
66 NON ADD CODE TEXT #
67 COPY RECEIPT TITLE COPY
68 EJ REPORT TITLE EJ
69 EJ REPORT END TITLE EJ END
X: LINE NO. (1 to 6)
(CHARACTERS): CHARACTER (Max. 24 Characters)
YYY3 [00] KEY
YYY : CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
F-NO. FUNCTIONDEFAULT12345678
(CHARACTERS)
NO CHANGE
LINE NO.XSBTL @/FOR SBTL4 CA/AT
PRESENTS THE
BEST ECR
I STHE BEST
SHARP
SHARPMRS =
XE-A21S PROGRAM MODE
2 – 6
-
15) PROGRAMMING OF CLERK NAME
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:
MRS = CLERKxx (xx: clerk no.)
16) FOREIGN CURRENCY SYMBOL PROGRAMMING
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:
MRS = ____ ( _ : space code)
Note: This symbol is printed as the amount of CURRENCY
CONVER-SION for PRESET RATE only.The amount symbol of CURRENCY
CONVERSION for OPEN RATE is not printed.
17) TAX TABLE PROGRAMMING
72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAXTABLE.(Case of
interval between break point is 1 dollar or more and less than100
dollar, 36 breakpoints is programmed for each table.)
* DEPRESSION OF THE [SBTL] KEY AT THE FOLLOWING POINTS MEANS A
TAX TABLE DELETE OPERATION.
MRS = NO TAX
18) TAX RATE PROGRAMMING
% TAX RATE &SIGN RATE xxx.xxxx = 0.0000 to 100.0000 %
LOWER TAX LIMITATION 0.00 to 999.99(This is invalid in VAT
system.)
MRS = DELETE
19) RATE HALO PROGRAMMING FOR [%] KEY
The DECIMAL POINT must be entered for setting the decimal
digits.
MRS = 100.00 (%)
XX: CLERK NO. (1 to 25)
(CHARACTERS): CHARACTER (Max. 8 Characters)
YYY3 [00] KEY
YYY : CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
(CHARACTERS): CHARACTER (Max. 4 Characters)
YYY3 [00] KEY
YYY : CHARACTER CODE (3 DIGITS)
(or [000] KEY ACCORDING TO PGM PRESET)
(CHARACTERS)
NO CHANGE
XXSBTL @/FOR SBTL5 CA/AT
(CHARACTERS)
NO CHANGE
SBTL SBTL6 CA/AT
SBTL @/FOR
CA/AT
SBTL
xx.xxxx
xxxx
AB
*
TAX RATE
CYCLExxx
INITIAL TAX
(Table Delete programming)
(Table Delete programming)
DECLARATION OF TAX
8
xxxxx
LOWER TAX LIMIT
@/FOR @/FOR
@/FOR @/FOR
xxxxx
BREAK POINT
@/FOR @/FOR
A: INTERVAL BETWEEN BREAKPOINTS A
BELOW 1 DOLLAR 0
1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR 1
B: TAX TABLE No. B
TABLE1 1
TABLE2 2
TABLE3 3
TABLE4 4
TAX RATE : 0.0001 to 99.9999
CYCLE : 0 to 9999
INITIAL TAX : 0 to 999
LOWER TAX LIMIT : 0 to 99999
BREAK POINT : 0 to 99999
A : TAX 1 PROGRAMMING 1
TAX 2 PROGRAMMING 2
TAX 3 PROGRAMMING 3
TAX 4 PROGRAMMING 4
XXX.XX: % HALO (0.00 to 100.00)
@/FOR
SBTL CA/AT
@/FOR9
0
0
(Inhibition programming)
xxx.xxxxTAX RATE
SBTL ATAX NO.
@/FOR xxxxx LOWER TAX LIMIT
FOR ADD TAX
XXX.XX
0
SBTL @/FOR % n29 CA/AT
XE-A21S PROGRAM MODE
2 – 7
-
20) [AUTO] KEY PROGRAMMING
It must be pushed same [AUTO] key as the programming [AUTO] key
atthe end of any key entry.
Note: [ESC] key cannot be set at [AUTO] key programming.It acts
as a key of ERROR ESCAPE function in this programming.
< [Auto] key function >
This machine has [AUTO] key which can be programmed the
key-sequence data.When [AUTO] key is depressed, the machine works
as same as theprogrammed key-sequence is entered.
21) DATE/TIME PROGRAMMING
Note: It cannot set the non-exist date (like Feb.-30th).
22) VARIOUS PROGRAMMING(EACH FUNCTIONS PROGRAMMING)
There are programmed by depressing ST-key after a data that want
toset. And it is operated continuously until depressing the
TL-key.
[JOB#1] MACHINE No. (6digits) -- XXXXXX --
MRS = 000000
[JOB#2] CONSECUTIVE No. (4digits) -- XXXX --
MRS = 0000
[JOB#5] FUNCTION SELECT -- ABCDEFGH --
MRS = 00000001
[JOB#6] PRINT FORMAT -- ABCDEFGH --
MRS = 11000011
Note: Case of RECEIPT, ECR is controlled the Journal Rewind
Motor as below.
Executing mode : REG, MGR, OPXZ, X1/Z1, X2/Z2
Setting mode : PGM
DATE) XXXXXXXX: YYYYMMDD (Year-month-day) orDDMMYYYY
(Day-month-Year) orMMDDYYYY (Month-day-Year)
(YYYY: 2000 to 2099)
(MM: 01 to 12)
(DD: 01 to 31)
The date entry format complies with the applicable
PGM-modeprogramming.
TIME) HH: Hour (00 to 23)
MM: Minute (00 to 59)
MRS = DATE: 01012000 (MM/DD/YYYY)
TIME: 0000
(Free key)
max 25
Delete
AUTO AUTO CA/AT
XXXXXXXX DATE
HHMM TIME
#/SBTL
(NK) #/SBTL
0
AB
AB : JOB No.NK : PROGRAMMING DATA. (Numeric Keys)
CA/AT#/SBTL @/FOR
A: PO in REG mode A
ENABLE 0 ★
DISABLE 1
B: RA in REG mode B
ENABLE 0 ★
DISABLE 1
C: SUBTOTAL VOID in REG mode C
ENABLE 0 ★
DISABLE 1
D: INDIRECT VOID in REG mode D
ENABLE 0 ★
DISABLE 1
E: DIRECT VOID in REG mode E
ENABLE 0 ★
DISABLE 1
F: REFUND in REG mode F
ENABLE 0 ★
DISABLE 1
G: NO SALE in REG mode G
ENABLE 0 ★
DISABLE 1
H: FRACTIONAL QUANTITY H
YES (3digits decimal place) 0
NO 1 ★
A: PRINTER FORMAT A
JOURNAL 0
RECEIPT 1 ★
REG/MGR/VOID mode : Journal Rewind Motor is not driven.
PGM/OPXZ/XZ mode : Journal Rewind Motor is driven for rewinding
reports anytime.
B: CONTENTS OF RECEIPT B
TOTAL 0
DETAIL 1 ★
C: TIME PRINTING (for all receipt) C
PRINT 0 ★
NOT PRINT 1
D: DATE PRINTING (for all receipt) D
PRINT 0 ★
NOT PRINT 1
XE-A21S PROGRAM MODE
2 – 8
-
[JOB#7] RECEIPT PRINT FORMAT -- ABCDEFGH --
MRS = 00000000
[JOB#10] POWER SAVING -- YXXX --
MRS = 0030
[JOB#11] LOGO PRINTING -- A --
MRS = 1
[JOB#15] FUNCTION SELECT2 -- ABCDEFGH--
MRS = 000000000
[JOB#19] QUANTITY FOR DOUGHNUT EXEMPT -- XX --(for CANADIAN
TAX)
MRS = 0
xx : QUANTITY FOR DOUGHNUT TAX EXEMPT = 0 to 99
[JOB#35] ONLINE COMMUNICATION TIME OUT -- XXX --
MRS = 007
XXX: Time out time (1 to 255 sec)
[JOB#50] THERMAL PRINTER DENSITY CONTROL -- XX --
MRS = 50
XX: density (00 to 99)
00 : 70 % for standard 50 : 100 % (Standard density) 99 : 130 %
for standard
[JOB#61] OTHERS1 PROGRAMMING -- ABCDEFGH --
MRS = 00100002
E: CONSECUTIVE NO. PRINTING E
PRINT 0
NOT PRINT 1 ★
F: Not used (Fixed at “0”)
G: ZERO SKIP IN PLU REPORT G
NOT SKIP 0
SKIP 1 ★
H: ZERO SKIP IN GENERAL,CLERK,HOURLY H
NOT SKIP 0
SKIP 1 ★
A, B: Not used (Fixed at “00”)
C: SUBTOTAL PRINT [AT] [SBTL] KEY C
NOT PRINT 0 ★
PRINT 1
D: MDSE SBTL PRINT AT [MDSE SBTL] KEY D
NOT PRINT 0 ★
PRINT 1
E, F, G: Not used (Fixed at “000”)
H: PURCHASE NO. PRINTING H
PRINT 0 ★
NOT PRINT 1
Y: POWER SAVING function when a time is displayed Y
Yes (Enable) 0 ★
No (Disable) 1
XXX: POWER SAVING TIME to POWER OFF= 001 to 254 (minutes) or 999
(Inhibit)
A: LOGO MESSAGE CONTROL A
3-LINE HEADER INSTEAD OF GRAPHIC LOGO 0
GRAPHIC LOGO ONLY 1 ★
GRAPHIC LOGO AND 3-LINE FOOTER 2
6-LINE HEADER 3
GRAPHIC LOGO AND 3-LINE HEADER 4
3-LINE HEADER AND 3-LINE FOOTER 5
A, B, C, D, E, F: Not used (Fixed at “000000”)
G: TAX DELETE in REG mode G
ENABLE 0 ★
DISABLE 1
H: MANUAL TAX in REG mode H
ENABLE 0 ★
DISABLE 1
A, B: Not used (Fixed at “00”)
C: Programming of MINUS dept/PLU C
Disable 0
Enable 1 ★
D: Fractional treatment D
Round off (4-DOWN, 5-UP) 0 ★
Raising to unit 1
Disregarding 2
E: [00] key or [000] key selection for [00] key position E
[00] key 0 ★
[000] key 1
F: Time format F
12hour 0 ★
24hour 1
G: Date format G
M-D-Y 0 ★
D-M-Y 1
Y-M-D 2
H: TAB H
0 0
1 1
2 2 ★
3 3
XE-A21S PROGRAM MODE
2 – 9
-
[JOB#62] OTHERS2 PROGRAMMING -- ABCDEFGH --
MRS = 00000000
[JOB#63] OTHERS3 PROGRAMMING -- ABCDEFGH --
MRS = 01010001
[JOB#64] OTHERS4 PROGRAMMING -- ABCDEFGH --
MRS = 00000000
[JOB#65] OTHERS5 PROGRAMMING -- ABCDEFGH --
MRS = 00000000
A: Not used (Fixed at “0”)
B: ERROR BEEP for missoperation B
LOCK ERROR 0 ★
MISSOPERATION 1
C: Key catch sound C
Yes 0 ★
No 1
D: Buffered Keyboard D
Yes 0 ★
No 1
E: VOID mode E
Enable 0 ★
Disable 1
F: Printing of VOID MODE in Z2 report F
Yes 0 ★
No 1
G: Printing of VOID MODE in Z1 report G
Yes 0 ★
No 1
H: Addition to the hourly total in VOID MODE H
No 0 ★
Yes 1
A: Receipting at the time of NO SALE A
Yes 0 ★
No 1
B: NO SALE after non-add code entry B
Disable 0
Enable 1 ★
C: NON-ADD code entry C
Enable 0 ★
Disable 1
D: Copy Receipt D
No 0
Yes 1 ★
E: Entry that causes the merchandise SUBTOTALto be smaller than
zero. E
Enable 0 ★
Disable 1
F: Subtotal entry before tendering F
Noncompulsory 0 ★
Compulsory 1
G: Subtotal entry before direct non-tender finalization G
Noncompulsory 0 ★
Compulsory 1
H: Direct non-tender finalization after tendering H
Disable 0
Enable 1 ★
A: Printing of GT1 on Z report A
Yes 0 ★
No 1
B: Printing of GT2 on Z report B
Yes 0 ★
No 1
C: Printing of GT3 on Z report C
Yes 0 ★
No 1
D: Printing of Training GT on Z report D
Yes 0 ★
No 1
E: Printing of Z counter on Z report E
Yes 0 ★
No 1
F: Printing of DATA on PLU resetting report F
Yes 0 ★
No 1
G: Reset GT1,2,3 at the general Z1 report G
No 0 ★
Yes 1
H: OP X/Z report H
Enable 0 ★
Disable 1
A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”)
XE-A21S PROGRAM MODE
2 – 10
-
[JOB#66] OTHERS6 PROGRAMMING -- ABCDEFGH --
MRS = 10001100
[JOB#67] OTHERS7 PROGRAMMING -- ABCDEFGH -- MRS = 00000000
[JOB#68] OTHERS8 PROGRAMMING -- ABCDEFGH --
MRS = 00100011
[JOB#69] OTHERS9 PROGRAMMING -- ABCDEFGH --
MRS = 00000000
[JOB#70] OTHERS10 PROGRAMMING -- ABCDEFGH --
MRS = 00000000
A: AFTER-TRANSACTION RECEIPT A
TOTAL ONLY 0
DETAILS 1 ★
B: AMOUNT PRINTING WHEN PLU UNIT PRICE IS 0 B
No 0 ★
Yes 1
C: CONVERSION SBTL PRINTING OF NATIVE SBTL C
Yes 0 ★
No 1
D: Not used (Fixed at “0”)
E: Compression print on journal at PGM/XZ mode E
No (Normal size) 0
Yes (Small size) 1 ★
F: Compression print on journal at REG/MGR/VOID mode F
No (Normal size) 0
Yes (Small size) 1 ★
Note: This selection is valid only when “PRINTING FORMAT” isset
as “JOURNAL”. This selection is not valid for the printing data of
EJ report.It is provided another selection job for EJ.
G: Logo Text Print on Journal G
No 0 ★
Yes 1
H: FOOTER PRINT CONTROL H
ALL RECEIPTS 0 ★
ON SELECTED FUNCTION KEY AT THE TIMEOF FINALIZATION 1
A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”)
A, B: Not used (Fixed at “00”)
C: Temporary journal printing function of transaction C
Disable 0
Enable 1 ★
Note: It is a function to print one transaction data which is
notfinalized (during a transaction) when a transaction is oper-ated
at “RECEIPT OFF”.It is available only at “RECEIPT PRINTER
TYPE”.
D: EJ print and clear at general Z1 report D
No 0 ★
Yes 1
E: PGM mode programming operation records in EJ E
DETAIL 0 ★
Header information only 1
Note: It is not effected for PGM reading and XZ reports.PGM
reading and XZ reports are always treatment as“HEADRER ONLY”.
F: REG/MRG/VOID operation records in EJ F
DETAIL 0 ★
TOTAL 1
G: Compression print for EJ report G
No (Normal size) 0
Yes (Small size) 1 ★
H: Action when EJ file is full H
Continue (No warning) 0
Warning (near full warning) 1 ★
Lock (with near full warning) 2
A, B, C, D, E: Not used (Fixed at “00000”)
F: TAX PRINTING WHEN TAXABLE SUBTOTAL IS ZERO F
No 0 ★
Yes 1
G: TAX PRINTING WHEN TAX IS ZERO G
Yes 0 ★
No 1
H: Not used (Fixed at “0”)
A: SPLIT PRICING COUNTING A
QUANTITY 0 ★
PACKAGE 1
B: MULTIPLICATION ENTRY SYSTEM B
MULTIPLICATION ONLY 0 ★
SPLIT PRICING & MULTIPLICATION 1
C, D: Not used (Fixed at “00”)
E: TAX PRINTING WHEN GST is VAT E
Yes 0 ★
No 1
F: GST EXEMPT on X/Z F
PRINTED 0 ★
NOT PRINTED 1
GH: TAX SYSTEM = 00 to 11
AUTO TAX = 00
CANADA TAX (GST TYPE nn) = 01 to 11
XE-A21S PROGRAM MODE
2 – 11
-
[JOB#71] GT2 PROGRAMMING -- XXXXXXXXXXXXX --
MRS = 0000000000000
XXXXXXXXXXXXX : GT (13digits)
[JOB#72] GT3 PROGRAMMING -- XXXXXXXXXXXXX --MRS =
0000000000000
XXXXXXXXXXXXX : GT (13digits)
[JOB#76] GENERAL Z1 RESET REPORT COUNTER -- XXXX --MRS =
0000
XXXX : RESET COUNTER (4digits)
[JOB#77] GENERAL Z2 RESET REPORT COUNTER -- XXXX --MRS =
0000
XXXX : RESET COUNTER (4digits)
[JOB#86] TRAINING CLERK PROGRAMMING -- XX --MRS = 0
X : CLERK No. = 0 (INHIBIT), 1 to 25
23) DOMESTIC CURRENCY SYMBOL PROGRAMMING
(CHARACTERS): CHARACTER (Max. 4 Characters)
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:
YYY 3 [00] KEYYYY : CHARACTER CODE (3 DIGITS)(or [000] KEY
ACCORDING TO PGM PRESET)
MRS = ___$ ( _ : space code)
This symbol is printed with (+) amount of domestic currency.The
programmed characters is printed at left side of amount.
Ex) Case of “ US$ ”: | DEPT.01 US$1.00 | 2 Programmed symbol
If some space characters are programmed at the left side of
symbol(like “ $”), they are not counted as the number of character
of the cur-rency symbol. (In case of “ US$”, the number of
character is 3.)
Ex) Case of “ US$”: (The currency symbol means “US$”)
|AAAADEPARTMENT01 US$10000.00 | 2 Programmed symbol
24) TRAINING MODE TEXT PROGRAMMING
(CHARACTERS): CHARACTER (Max. 8 characters)
Characters can be entered by using the character layout on
keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE
FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:
YYY 3 [00] KEYYYY : CHARACTER CODE (3 DIGITS)(or [000] KEY
ACCORDING TO PGM PRESET)
MRS = TRAINING
25) TEXT CHANGING (TO DEFAULT TEXT)
X: 0 = English text3 = Spanish text
MRS = 0
When this job is executed, below texts are set as default
data.
(a) Function text(b) Each message text (LOGO, etc..)
26) RESETTING OF ALL COUNTER AND TOTALIZER
All counter, totalizer, EJ data all GTs, and all Z counter are
reset.
(CHARACTERS)SBTL SBTL85 CA/AT
NO CHANGE
(CHARACTERS)SBTL SBTL87 CA/AT
XSBTL @/FOR88 CA/AT
0
HEADER
*PGM* MODE TITLE
LANGUAGE MODE
05/02/2006 12:34PM
123456#1234
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
#88 0
01
BETTY___
SBTL 89 CA/TL@/FOR
HEADER
*PGM* MODE TITLE
JOB#
05/02/2006 12:34PM
123456#1234
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
#89
01
BETTY___
XE-A21S PROGRAM MODE
2 – 12
-
27) CHANGING MEMORY TYPE(EJ RECORD AND PLU RECORD)
X : 0 = TYPE1 (EJ: 2000 records and PLU 1200 records)1 = TYPE2
(EJ: 3000 records and PLU 210 records)
MRS = 0
When this job is executed, EJ records are deleted and PLU
records areset the default data after deleted all records even if
same memory typeis entered.
28) MAXIMUM NUMBER OF DEPARTMENTT
XX : Max Number of DEPARTMENT
This job is used for the limitation of below functions.
(1) Programming for the department code over the maximum num-ber
of department.
(2) Registration for the department code over the maximum
num-ber of department.
(3) Registration for the PLU that is associated to department
overthe maximum number of department.
(4) Printing for the department data over the maximum number
ofdepartment at PGM READING and XZ REPORTS.
MRS = 99
29) SD CARD FUNCTION
[Key Sequence of SD Jobs]
(*1) When [SBTL] key is pushed, ECR prints the confirmation
messageat “RECEIPT” (not print at JOURNAL) and enforces to select
eitherexecuting or canceling this job. The buffered keys are
cleared.
(*2) “1” is a keyword to execute this job.
(*3) If the MODE SWITCH is turned to another mode from PGM
positionor the AC POWER is off when job is executed, the job is
cancelled.
Note: If AC POWER is off when ECR accesses SD CRAD, the
contentsin SD CARD may be broken.
The action of each job is as below.
[JOB#140] Format SD CARD
This job formats SD card. (It deletes all data on SD card.)After
formatting card, the folder \SHARP\ECRXXX01 is made to a
rootdirectory.And then, \ALL, \PROGRAM, \SALES, \EJPRINT, \EJ and
\LOGO aremade to a folder “\SHARP\ECRXXX01”.The file “SRECORD.REC”
is made to both folder“\SHARP\ECRXXX01\SALES” and
“\SHARP\ECRXXX01\EJ”and it is set the default data.Notes: • All the
data currently written in SD card is erased.
• The file “SRECORD.REC” is used for control the structureunder
each folder.Any users dose not need to concern itscontents.
[JOB#141] Programming data saving to SD CARD
[JOB#147] Programming Data loading from SD CARD
The below data is saved or loaded. Files are set in the folder
for “Programming Data”.
(*1) The contents of each file are same as the communication
data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are
described in “ONLINE SPECIFICATION”. All data are converted touse
at “Customer Support Tool” software on PC.
Notes: • If there is data of the same file name, the message of
confir-mation does not display.Data is overwritten if there is data
of the same file name.
• Each files are used only for the “Customer Support Tool”
soft-ware on PC. Any users dose not need to concern its
contents.
xxx : JOB code
140 : Format SD CARD
141 : Save Programming Data (ECR 3 SD)
144 : Save All RAM Data (ECR 3 SD)
145 : Load Graphic Logo Data (ECR 1 SD)
147 : Load Programming Data (ECR 1 SD)
148 : Load All RAM Data (ECR 1 SD)
XSBTL @/FOR90 CA/AT
HEADER
*PGM* MODE TITLE
MEMORY TYPE (0: TYPE1, 1: TYPE2)
05/02/2006 12:34PM
123456#1234
DATE/TIME/CLERK NO
MACHINE NO. /CC-NO. /CLERK NAME
#90 0
01
BETTY___
XXSBTL @/FOR95 CA/AT
xxx 1@/FOR CA/AT
CL
SBTLSBTL
(*1) (*2)
: Execute operation (*3)
: Cancel
File Name File/Table No. (*1) Field (*1)
1 Date and Time mtimtbl D0
2 Department deptdata 01 B000(Label, Preset, Price, Text)
3 PLU pludata 11 B000(Label, Preset, Price, Text)
4 Function programming
FuncText A4
Mfunctbl D8
5 Tax Table andRate
mtaxtbl D7
6 Logo message mlgxtbl D2
7 Clerk CsrData 51 All fields
8 Others Programming
mopttbl D1
XE-A21S PROGRAM MODE
2 – 13
-
[JOB#145] Graphic logo data loading
The below data is loaded. Files are set in the folder for “LOGO
Data”.
(*1) The contents of each file are same as the communication
data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.”
aredescribed in “ONLINE SPECIFICATION”. All data are converted
touse at “Customer Support Tool” software on PC.
Note: Files are created only for the “Customer Support Tool”
softwareon PC. Any users dose not need to concern its contents.
[JOB#144] All Data Saving
[JOB#148] All Data LoadingNotes: • In case of “DATA SAVING”, the
message of confirmation for
overwritten the file on SD Card does not display. Data is
over-written if there is data of the same file name.
• In case of “DATA LOADING”, the condition of ECR will returnto
past condition. However, the message of confirmation foroverwritten
does not display.
The below data is saved or loaded. Files are set in the folder
for “ALLRAM BACKUP”.
Note: Each files are used only for the purpose of DATA BACKUP
atECR. Any users dose not need to concern its contents.
■ DISPLAY AND PRINT:
File Name File/Table No. (*1) Field (*1)
1 Graphic LOGO LOGO E0
File Name
1 All RAM data All
Key Display Print NOTE
1 2 3 4 5 6 7 8 9 0
[STBL] P
141 P 1 4 1
[@/FOR] P 1 4 1
[SBTL] P -The buffered keys are cleared and the message
isprinted on “receipt” only. (It is not print on “journal” and
“EJ”.)
MESSAGE : MAX 8-lines(The message is fixed in ROM.)
(Not count up CC# at this time.)
[1] P 1
[CA/AT] S d - A C C E S S . (Count up CC#.)DISPLAY : “.” is
blinking while executing job.
PRINT : JOB HEADDER is printed.And job code is printed.(Job code
is printed only at SD jobs)
(SD ACCESS) S d - A C C E S S . DISPLAY: “.” is blinking while
executing job. PRINTPRINT : (NON)
Case of NORMAL END 0. 0 0 DISPLAY: (INITIAL)PRINT : STATUS is
printed(The message is fixed in ROM.)
Case of ERROR END E - S d - 0 1 DISPLAY: ERROR CODE
(2-digits)PRINT : SD ERROR MESSAGE and ERROR
CODE (The message is fixed in ROM.)
Case of CHANGINGMODE KEY (to cancel)
0. 0 0 DISPLAY: (INITIAL)PRINT : SD CANCEL MESSAGE(The message
is fixed in ROM.)
Case of POWER OFF E - S d - P. O F F DISPLAY: ERROR MESSAGEPRINT
: MESSAGE of POWER OFF(The message is fixed in ROM.)
123456789012345678901234
(PRE-PRINT HEADDER)! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
!YOU SELECT SD CARD JOBPUSH [1]-KEY to EXECUTEPUSH [CL]-KEY to
CANCEL! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Don't turn the mode keywhile executing a job.
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !(Issuing
Receipt)
HEADER
*PGM*
05/02/2006 12:34PM
123456#1234
#141
01
BETTY___
***NORMAL END
(Issuing Receipt)
SD ERROR
(Issuing Receipt)
01
SD CANCELED
(Issuing Receipt)
POWER OFF ERRORAT THE DEVICE CONTROLSET DATA&TIME AGAIN
(Issuing Receipt)
XE-A21S PROGRAM MODE
2 – 14
-
3. CHARACTER ASSIGNMENT METHOD
■ PROGRAMMING KEY LAYOUT
Note: The small characters on the bottom or lower right in each
key indications or characters which can be used for character
entries for text programming.
■ THE METHOD OF CHARACTER ENTRY AT TEXT PROGRAMMINGThe character
can be entered by using character key or character code.
When the character can be entered in the text programming, the
key layout is changed from “Function and [DEPT] key layout” to
“CHARACTER KEYLAYOUT”.
In “CHARACTER KEY LAYOUT”, any key except the Numeric keys and
[CL], [SBTL], [CA/AT] are assigned either the character or the
control key forcharacter entry.
Any character can be entered by following method.
By character key:
By Numeric key (Character Code) :
(The list of Control Key)
The status of [SHIFT], [NUMBER] and [DC] are keeping until
pushing same control key in each text entry. (STAY DOWN type)
And the corresponding indication is lighted up on the display
while their status is “on”.
(Example)
Key Action
SHIFT Entry to shift the following character key. (ex. [SHIFT] 3
[A] : Enter the character “a”.)
NUMBER Entry the following numeric key as the number character.
(ex. [NUMBER] 3 [1] : Enter the character “1”.)
(DC) Double size character: Change the following character to
the double size character.
BS Back Space : Delete the last character.
[SHIFT] 3 [A] [B] [C] 3 [SHIFT] 3 [A] [B] [C] : Text
“abcABC”.
[NUMBER] 3 [1] [2] [3] 3 [NUMBER] 3 [1] [2] [3] : Text “123” and
numeric number 123.
[DC] 3 [A] [B] [C] 3 [DC] 3 [A] [B] [C] : Text “ABCABC”.
: Characters on Character key layout.
: Numeric character ("0"), "1", . . . , "9")
SHIFT (CHARACTER KEY)
NUMBER (NUMERIC KEY)
xxx [00]
xxx : Character Code
XE-A21S PROGRAM MODE
2 – 15
-
Printer
CODE CHARACTER
001 á
002 â
003 ê
004 î
005 ì
006 í
007 ô
008 ó
009 û
010 ú
011 œ
012
013 ú
014
015 ó
016 Λ
017 Ψ
018 Γ
019 ..
020 Ω
021 ∆
022 Θ
023 Ξ
024 Π
025 Σ
026 Υ
027 Φ
028
029 Ú
030
031 Ó
032 (Space)
033 !
034 "
035 #
036 $
037 %
038 &
039 '
040 (
041 )
042 *
043 +
044 ,
045 –
046 .
047 /
048 0
049 1
050 2
051 3
052 4
053 5
054 6
055 7
056 8
057 9
058 :
059 ;
060 <
061 =
062 >
063 ?
064 @
065 A
066 B
067 C
068 D
069 E
070 F
071 G
072 H
073 I
074 J
075 K
076 L
077 M
078 N
079 O
080 P
081 Q
082 R
083 S
084 T
085 U
086 V
087 W
088 X
089 Y
090 Z
091 Ä
092 Ö
093 Ü
094 ^
095 _
096
097 a
CODE CHARACTER
098 b
099 c
100 d
101 e
102 f
103 g
104 h
105 i
106 j
107 k
108 l
109 m
110 n
111 o
112 p
113 q
114 r
115 s
116 t
117 u
118 v
119 w
120 x
121 y
122 z
123 {
124 |
125 }
126 ß
127
128 !!
129 1
130 2
131 3
132 4
133 1/2134 F T135 1
136 3
137 p
138 p
139 d
140 e
141 F
142 T
143 4
144 ç
145 O
146 ¿
CODE CHARACTER
147 ù
148 à
149 Æ
150 φ
151 Å
152 ¤
153 é
154 è
155 Pt
156 ¡
157 Ñ
158 Õ
159 £
160 ¥
161
162
163
164
165 .
166 T 1167 T 2168 T 3169 T 4170 1 2171 1 3172 1 4173 2 3174 2
4175 3 4176
177 Á
178
179
180 A
181 a
182 E
183 e
184 I
185 i
186 U
187 u
188
189
190
191 Š
192
193
194
195
CODE CHARACTER
196
197
198
199
200
201
202
203
204
205
206
207
208 P
209
210
211 š
212
213
214
215
216
217
218
219
220
221
222
223
224 *
225 §
226 Ø
227 ^
228 2
229 ]
230 [
231
232 ä
233 ö
234 ü
235 æ
236 å
237 É
238 ñ
253 (DC)
CODE CHARACTER
Note: The character of this table is for reference. Please see
actual display.(DC) : Double Code : ECR Control Character (Not used
for text)
XE-A21S PROGRAM MODE
2 – 16
-
4. HELP FUNCTION
This function prints guidance messages of main cash register
functions
by pushing the HELP key. If you push a number key and the HELP
key
following the guidance messages, more detailed guidance
messages
will be printed.
[PURPOSE]
The aim is to be able to easily program the register by printing
the guid-
ance messages.
[PROGRAMMING]
(PGM-mode)
Follow the setup features below for the desired HELP printing
settings.
JOB#6-A : Printer format receipt/journal.
JOB#66-E : Compression print on journal at PGM/XZ mode Small
size/
Normal size.
JOB#66-F : Compression print on journal at REG/MGR/VOID mode
Small size/Normal size.
(REG/MGR-mode)
Even if ECR is in a receipt-off state, HELP printing is
executed.
(Other)
HELP printing is written in electronic journal.
[OPERATION]
1. Available Mode of Help function
PGM, VOID, O/P X/Z, REG, MGR, X1/Z1, X2/Z2
2. The proper timing of when the HELP function will work is when
the
transaction is finalized, not during the transaction
operation.
Key operating sequences
If [HELP] key is pressed on the ECR, the following receipt is
printed.
1-[HELP]: DATE/TIME
key No. Print menu
[HELP] 1 Date/Time setup
2 Rate of TAX setup
3 Department setup
4 Sales Z report
5 Logo setting
6 Receipt issue
7 What is P in Display
8 What is ERROR 32
9 SD card command
10 Install PC software
XX HELP
Help Menu
Help No.
HEADER
05/02/2006 12:34PM 01123456#1234 BETTY___
HELP MENU
1-[HELP]: DATE/TIME2-[HELP]: TAX3-[HELP]: DEPARTMENT4-[HELP]:
SALES Z REPORT5-[HELP]: LOGO6-[HELP]: RECEIPT7-[HELP]: P IN
DISPLAY8-[HELP]: ERROR 329-[HELP]: SD CARD10-[HELP]: PC S/W
INSTALL------------------------OTHER ISSUE: PLEASE CALL
1-800-BE-SHARP
MACHINE NO. /CC-NO. /CLERK NAME
MODE TITLE
DATE/TIME/CLERK NO
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
(PGM MODE)DATE:XXXXXXXX-[SBTL] YYYYMMDD OR DDMMYYYY OR
MMDDYYYY(DEFAULT)TIME:HHMM-[SBTL] (0000-2359)EX) 08/01/2006 PM4:30
(DATE FORMAT=M-D-Y) 08012006-[SBTL]1630-[SBTL]
05/02/2006 12:34PM 01123456#1234 BETTY___
1 DATE/TIME SETUP
HEADER
XE-A21S PROGRAM MODE
2 – 17
-
2-[HELP]: TAX
3-[HELP]: DEPARTMENT
4-[HELP]: SALES Z REPORT
5-[HELP]: LOGO
HEADER
05/02/2006 12:34PM 01 123456#1234 BETTY___
2 TAX RATE SETUP
(PGM MODE)
R:RATE(0.0000-100.0000%)
[SBTL]-9-[@]-N-[@]-R-[@]-Q-[SBTL]-[CA]
EX) TAX1(RATE=6.25%),
Q:MIN. TAXABLE AMOUNT
-[@]-300-[SBTL]-[CA]
MIN. AMT=$3.00[SBTL]-9-[@]-1-[@]-6.25
MACHINE NO. /CC-NO. /CLERK NAME
MODE TITLE
N:TAX NUMBER (1-4)
(0.00-999.99)
DATE/TIME/CLERK NO
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
(PGM MODE)1)PRICEXX-[DEPT#]-YYYYYY- [SBTL]-[CA]XX:DEPARTMENT
CODE(1-99)YYYYYY:UNIT PRICE
(MAX.6DIGITS)2)TEXT[SBTL]-1-[.]-XX-[DEPT#]-(TEXT)-[SBTL]-[CA]XX:DEPT
CODE(1-99)TEXT CAN BE ENTERED BYUSING THE CHARACTERLAYOUT ON
KEYBOARD ORNUMERIC KEY ON KEYBOARD.
05/02/2006 12:34PM 01123456#1234 BETTY___
3 DEPARTMENT PRICE&TEXT
HEADER
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
SALES Z REPORT SHOWS THEDAILY/ PERIODIC SALES1. DAILY Z
REPORT(X1/Z1 MODE) [.]-[CA]: GENERAL [.]-[PLU]: PLU [.]-[CLK#]:
CLERK [.]-[SBTL]: HOURLY2. PERIODIC Z REPORT(X2/Z2 MODE) [.]-[CA]:
GENERAL
05/02/2006 12:34PM 01123456#1234 BETTY___
4 SALES Z REPORT
HEADER
HEADER
05/02/2006 12:34PM 01123456#1234 BETTY___
5 LOGO SETTING
(PGM MODE)1)LOGO FORMAT[SBTL]-11-[@]-A-[SBTL]- [CA]A=0:3LINE
HEADER 1:GRAPHIC LOGO ONLY 2:GRAPHIC+3LINE FOOTER 3:6LINE HEADER
4:GRAPHIC+3LINE HEADER 5:3LINE HEADER/FOOTER2)LOGO
TEXT[SBTL]-4-[.]-L-[@]- (TEXT)-[SBTL]-[CA]L:LINE NUMBER(1-6)TEXT
CAN BE ENTERED BYUSING THE CHARACTERLAYOUT ON KEYBOARD ORNUMERIC
KEY ON KEYBOARD.3)GRAPHIC LOGOPLEASE REFER TOCUSTOMER SUPPORT
TOOL
MACHINE NO. /CC-NO. /CLERK NAME
MODE TITLE
DATE/TIME/CLERK NO
XE-A21S PROGRAM MODE
2 – 18
-
6-[HELP]: RECEIPT
7-[HELP]: P IN DISPLAY
8-[HELP]: ERROR 32
9-[HELP]: SD CARD
10-[HELP]: PC S/W INSTALL
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
05/02/2006 12:34PM 01123456#1234 BETTY___
6 RECEIPT ISSUE
WHETHER ISSUE RECEIPT ORNOT CAN BE CHANGED BYDEPRESSING [RCPT]
KEYIF THE INDICATOR "_" APPEARS ONDISPLAY, RECEIPT IS NOTISSUED, IN
THIS CASE,DEPRESSING [RCPT] KEY WILL ENABLE RECEIPTPRINT AGAIN
HEADER
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
05/02/2006 12:34PM 01123456#1234 BETTY___
7 WHAT IS P IN DISPLAY
[ERROR STATUS]
PAPER EMPTY[RESOLUTION]
INSERT NEW ROLL PAPER
HEADER
HEADER
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
05/02/2006 12:34PM 01
123456#1234 BETTY
8 WHAT IS ERROR 32
[ERROR STATUS]
NO ENTRY OF CLERK CODE[RESOLUTION]
ENTER A CLERK CODE
EX) ENTRY OF CLERK #1
1-[CLK#]
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
05/02/2006 12:34PM 01123456#1234 BETTY___
9 SD CARD COMMAND
(PGM MODE)[SBTL]-XXX-[@]-[SBTL]
XXX=140:FORMAT141:SAVE PROGRAMMING144:SAVE ALL RAM145:LOAD
GRAPHIC LOGO147:LOAD PROGRAMMING148:LOAD ALL RAM(X1/Z1 MODE)
SAVE SALES DATA 650-[.]-[@]-[SBTL]
SAVE AND CLEAR EJ DATA 750-[.]-[@]-[SBTL]
PRINT EJ DATA ON SD 740-[@]-[SBTL]
HEADER
DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME
MODE TITLE
05/02/2006 12:34PM 01123456#1234 BETTY___
10 INSTALL PC SOFTWARE
1.INSERT CUSTOMER SUPPORT CD IN YOUR PC2.INSTALLATION PROGRAM
RUNS AUTOMATICALLY(FOR USB CONNECTION)
3.AFTER INSTALLATION OF SOFTWARE,-TURN OFF ECR-CONNECT PC AND
ECR VIA USB CABLE-TURN ON ECR-SELECT "INSTALL THE SOFTWARE
AUTOMATICALLY" AT HARDWARE WIZARD
HEADER
XE-A21S PROGRAM MODE
2 – 19
-
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE
Roughly speaking, the following sales reports are available:
1) OP X/Z reports (Individual cashier reports)
2) X1/Z1 reports (Daily total X and Z reports)
3) X2/Z2 reports (Periodic total X and Z reports)
4) Flash-read reports (Display sales amount)
In addition to the above reports that are to be used for program
check-ing are also available.
[Purpose]The reports are each used to check sales data. The
standard purposesof taking these reports are as follows:
OP X/Z reports : These reports are taken by operators in order
toreport their own sales data.
X1/Z1 reports : These reports are taken by the supervisor or
manager inorder to check and report daily sales totals at that
point.
X2/Z2 reports : These reports are taken by the owner or manager
inorder to check and report periodic (weekly or monthly)totals.
Flash-read : These reports are taken by the owner or manager
inorder to check and display sales totals at that point.
[Operation]
In the table below those reports marked with a circle “ ” can be
executed.
PRINTING REPORT
FLASH READING REPORT
OTHERS OPERATION
REPORT NAME KEYENTRY
MODE
DATA FOR READINGOPX/Z X1/Z1 X2/Z2
X Z X1 Z1 X2 Z2
GENERAL [CA/AT] *1, *6
PLU BY RANGE [PLU] PLU CODE *1, *2
CRERK (ALL) [CLK]# *1
CRERK (INDIVIDUAL) [CLK]# *1, *3
HOURLY (ALL) [#/SBTL] *1
REPORT NAME KEY ENTRY
MODE
DATA FOR READINGOPX/Z X1/Z1 X2/Z2
X Z X1 Z1 X2 Z2
DEPARTMENT [DPTn]or [SHIFT] 3 [DPTn]or NK 3 [DEPT#] DEPT
CODE
*4
CID [@/FOR] *4
PAID TOTAL [CA/AT] *4
REPORT NAME JOB#
MODE
DATA FOR READINGOPX/Z X1/Z1 X2/Z2
X Z X1 Z1 X2 Z2
EJ report (ALL) 700 *5, *6
EJ report (Latest 10 records) 710 *5, *6
MODE: X : Daily operater X report Z : Daily operater Z
report
X1 : Daily X report Z1 : Daily Z report
X2 : Periodic X report Z2 : Periodic Z report
(X report): The corresponding data is held in the ECR.
(Z report): The corresponding data is cleared in the ECR.
XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE
3 – 1
-
• Stop of printing reports (Report cancel function):This ECR has
the function of report stopping for PLU report and EJreport.
• Printing of GT on X reports:This ECR dose not print any GT on
X reports.
*1 To read respective reports, it is necessary to follow the
procedurebelow.
*2 PLU code range can be specified by entering the start and
endnumbers according to the following procedure.When specifying a
single PLU code, the start number has only to beentered.
*3 To read respective reports, it is necessary to follow the
procedurebelow. The clerk code does not need to enter at the OPX/Z
mode.In OPX/Z mode, it is issued the report of the assigned
clerk.
*4 Reading display only.The displayed amount can be cleared by
[CL] key.
*5 To read respective contents, it is necessary to follow the
procedure below.
*6 It is able to print and clear the EJ memory at general Z1
report byPGM mode programming.In that case, the contents of EJ
memory is printed just after issuedgeneral Z1 report.(Issuing
general Z1 report 3 Clear daily DEPT & TRANS memory 3Issuing EJ
memory 3 Clear EJ memory)
[Action]
Individual counters for the following Z reports are incremented
whenthose reports are printed.
1) General daily total report (Z1)
2) General periodic total report (Z2)
[Additional function]
(1) Overflow markIf the amount or quantity in any totalizer
other than GT to be printedon X or Z reports exceeds a programmed
limit, the indication mark(overflow mark) is printed for the
totalizer concerned.The overflow mark may be printed even if a
totalizer does not reachthe maximum amount. This occurs, for
example, when the amountor quantity in the totalizer gets smaller
than the maximum amountdue to the entry of a negative amount after
the overflowing of thetotalizer. This means that when the totalizer
overflows once, theoverflow mark (for example, “!!”) is
printed.
(2) MODE TITLEEach report is printed MODE TITLE at a header of
report.The Report Titles are as follows.
(3) Report cancel functionIt can be cancelled by turned the mode
switch to MGR position while the data is printed. (In this case,
the contents of memory arenot cleared.)
(X report)Reading
Resetting(Z report)
KEY
Start No.XXXX XXXX
End No.
All
PLU@/FOR
Resetting
Reading
CLKEY
(Display amount) (Display initialize)
JOB# @/FOR CA/AT
Resetting
Reading
OPX report *OPX*
OPZ report *OPZ*
X1 report *X1*
Z1 report *Z 1*
X2 report *X2*
Z2 report *Z 2*
::
* * * * * 1 the report cancel symbol
123456789012345678901234
XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE
3 – 2
-
ELECTRONIC JOURNAL REPORT
This job is own to print and clear EJ memory in X1/Z1 mode and
OPXZ mode.
[Key sequence]
1) Reading and resetting of all records:[OPXZ, X1/Z1 mode]
2) Reading of the latest 10 records:[OPXZ, X1/Z1 mode]
[ACTION]
It prints all or parts of printing data in EJ memory.The
printing format is same as each operation.
It is able to print and clear the EJ memory at general Z1 report
by PGMmode programming.In that case, the contents of EJ memory is
printed just after issued gen-eral Z1 report.(Issuing general Z1
report 3 Clear daily DEPT & TRANS memory 3Issuing EJ memory 3
Clear EJ memory)
[Report cancel function]
It can be cancelled by turned the mode switch to MGR position
while EJdata is printed. (In this case, the contents of EJ memory
are not cleared.)
[Key Sequence of SD Jobs]
(*1) When [SBTL]-key is pushed, ECR prints the confirmation
message at “RECEIPT” (not print at JOURNAL) and enforces toselect
either executing or canceling this job. The buffered keys
arecleared.
(*2) “1” is a keyword to execute this job.
(*3) If the MODE SWITCH is turned to another mode from X1Z1
position or the AC POWER is off when job is executed, the job
iscancelled.
Note: If AC POWER is off when ECR accesses SD CRAD, the
contentsin SD CARD may be broken.
The action of each job is as below.
[JOB#650] Sales data saving
All sales data (Daily and term) save in SD card.This job is used
for the purpose of using Electric Journal Data at the“Customer
Support Tool” software on PC. Maximum 400 times data iskept in SD
Card when the SD memory is not full.
The action is as below.
Step1) After reading the information of the current sub-folder
in“SRECORD.REC” file, ECR creates the new sub-folder underthe
folder for “Sales Data”.Its folder is named ASCII Character that is
indicated the numberof sales data in SD Card. (Example: “1”, “2”,
“3”,......)
Step2) Save the below data in new sub-folder that is created
above step.
Spet 3) Create the “STATUS.REC” file in new sub-folderwhen all
files are saved completely.
Step 4) Update the “SRECORD.REC” file for changing the structure
ofsub-folder.
(*1) The contents of each file are same as the communication
data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.”
aredescribed in “ONLINE SPECIFICATION”. All data are converted
touse at “Customer Support Tool” software on PC.
Note: Each files are used only for the “Customer Support Tool”
soft-ware on PC. Any users dose not need to concern its
contents.
[JOB#750] Electric Journal Saving and Clearing on memory
Electric journal data is saved in SD card.This job is used for
the purpose of using Electric Journal Data at the“Customer Support
Tool” software on PC. Maximum 400 times data iskept in SD Card when
the SD memory is not full.
Note: After saving EJ data, ECR is clear the Electronic Journal
memory.
xxx: JOB code
650: Save Sales Data (ECR 3 SD)
750: Save and Clear EJ Data (ECR 3 SD)
yyy: JOB code
740: Printing EJ Data on SD (ECR 1 SD)
CA/AT@/FOR
(Reading)
(Reseting)700
710 @/FOR CA/AT
xxx 1
yyy
@/FOR CA/AT
CL
SBTL
(*1) (*2)
: Execute operation (*3)
: Cancel
File Name File/Table No. (*1) Field (*1)
1 Date and Time(When a job is operated)
mtimtbl D0
2 Department Sales Dept 01 All fields
3 Transaction Sales Trans 21 All fields
Func Text A4
4 Hourly Sales Hourly 61 All fields
5 Clerk Sales Csr Data 51 All fields
Csr Sal 52 All fields
6 PLU Sales Plu 11 All fields,All range1
File Name
1 Status information STATUS.REC
File Name
1 Record structure SRECORD.REC
750 @/FOR CA/AT
XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE
3 – 3
-
The action is as below.
Step1) Save the below data in the folder for “Electric Journal
for printing”.
Step2) After reading the information of the current sub-folder
in“SRECORD.REC” file, ECR creates the new sub-folder underthe
folder for “Electric Journal Data”.Its folder is named ASCII
Character that is indicated the numberof sales data in SD Card.
(Example: “1”, “2”, “3”,......)
Step3) Save the below data in new sub-folder that is created
above step.
Spet4) Create the “STATUS.REC” file in new sub-folder when all
files are saved completely.
Step5) Update the “SRECORD.REC” file for changing the structure
of sub-folder.
Step6) Clear EJ DATA on memory at ECR.
(*1) The contents of each file are same as the communication
data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.”
aredescribed in “ONLINE SPECIFICATION”. All data are converted
touse at “Customer Support Tool” software on PC.
Notes: • The file in the EJPRINT folder on SD Card is
overwritten.The message of confirmation for overwritten the file in
theEJPRINT folder on SD Card does not display.
• Each files are used only for the “Customer Support Tool”
soft-ware on PC. Any users dose not need to concern its
contents.
[JOB#740] Electric journal print
ECR prints the below data that is already set in the folder for
“EJPRINT Data”.
(*1) The contents of each file are same as the communication
data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.”
aredescribed in “ONLINE SPECIFICATION”. All data are converted
touse at “Customer Support Tool” software on PC.
Notes: • It is printed only the newest EJ DATA (That is saved at
last byeither ECR or PC).
• Each files are used only for the “Customer Support Tool”
soft-ware on PC. Any users dose not need to concern its
contents.
■ DISPLAY AND PRINT: X1/Z1 MODE)
JOB ENTRY OPERATION: (Common action for all Jobs)
--- Continue to JOB END MESSAGE (NEXT PAGE)
File Name File/Table No. (*1) Field (*1)
1 EJ Data EJFILE A0
File Name File/Table No. (*1) Field (*1)
1 EJ Data EJFILE A0
File Name
1 Status information STATUS.REC
File Name
1 Record structure SRECORD.REC
File Name File/Table No. (*1) Field (*1)
1 EJ Data EJFILE A0
Key Display Print NOTE
1 2 3 4 5 6 7 8 9 0
750 [ . ] 7 5 0.
[@/FOR] 7 5 0.
[SBTL] - The buffered keys are cleared and the message isprinted
on “receipt” only. (It is not print on “journal” and “EJ”.)
MESSAGE: MAX 8-lines(The message is fixed in ROM.)
(Not count up CC# at this time.)
[1] 1
[CA/AT] S d - A C C E S S . (Count up CC#.)DISPLAY: “ . ” is
blinking
while executing job.PRINT : JOB HEADDER is printed.
And job code is printed.(Job code is printed only at SD
jobs)
Case of EJ PRINT:The EJ DATA is printed as same as EJREPORT
(#700) after printing job code.
(SD ACCESS) S d - A C C E S S . DISPLAY : “ . ” is blinkingwhile
executing job.
PRINT : (NON)
::
123456789012345678901234
(PRE-PRINT HEADDER)! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
!YOU SELECT SD CARD JOBPUSH [1]-KEY to EXECUTEPUSH [CL]-KEY to
CANCEL! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Don't turn the mode keywhile executing a job.
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !(Issuing
Receipt)
HEADER
*Z1*
05/02/2006 12:34PM
123456#1234
#750
01
BETTY___
XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE
3 – 4
-
[JOB END MESSAGE] Case of DATA SAVING (“SALES” or “EJ
DATA”):
The messages are printed on both RECEIPT and JOURNAL and
recorded in EJ memory.
[JOB END MESSAGE] Case of EJ DATA PRINTING:
The report cancel symbol is printed on both RECEIPT and JOURNAL,
but it is not recorded in EJ memory.The messages except the report
cancel symbol are printed on both RECEIPT and JOURNAL and recorded
in EJ memory.
[ERROR CODE LIST]
Key Display Print NOTE
1 2 3 4 5 6 7 8 9 0
NORMAL END 0. 0 0 DISPLAY: (INITIAL)PRINT : STATUS is printed
(The message is fixed in ROM.)
ERROR END E - S d - 0 1 DISPLAY: ERROR CODE (2-digits)PRINT : SD
ERROR MESSAGE and ERROR CODE(The message is fixed in ROM.)
CANCEL(CHANGING MODEKEY)
0. 0 0 DISPLAY: (INITIAL)PRINT : SD CANCEL MESSAGE(The message
is fixed in ROM.)
POWER OFF E - S d - P. O F F DISPLAY: ERROR MESSAGEPRINT :
MESSAGE of POWER OFF(The message is fixed in ROM.)
123456789012345678901234
***NORMAL END
(Issuing Receipt)
SD ERROR
(Issuing Receipt)
01
SD CANCELED
(Issuing Receipt)
POWER OFF ERRORAT THE DEVICE CONTROLSET DATA&TIME AGAIN
(Issuing Receipt)
Key Display Print NOTE
1 2 3 4 5 6 7 8 9 0
NORMAL END 0. 0 0 DISPLAY: (INITIAL)PRINT : (NON)
ERROR END E - S d - 0 1 DISPLAY : ERROR CODE (2-digits)PRINT :
The report cancel symbol, SD ERROR
MESSAGE and ERROR CODE(The message is fixed in ROM.)
CANCEL(CHANGING MODEKEY)
0. 0 0 DISPLAY: (INITIAL)PRINT : The report cancel symbol and
SD
CANCEL MESSAGE(The message is fixed in ROM.)
POWER OFF E - S d - P. O F F DISPLAY: ERROR MESSAGEPRINT : The
report cancel symbol, POWER OFF
ERROR MESSAGE and Notes message(The message is fixed in
ROM.)
123456789012345678901234
(Issuing Receipt)
SD ERROR 01* * * * * *
(Issuing Receipt)
SD CANCEL* * * * * *
(Issuing Receipt)
POWER OFF ERRORAT THE DEVICE CONTROLSET DATA&TIME AGAIN
(Issuing Receipt)
* * * * * *
No. Description
01 SD card is not find
02 SD CARD PROTECT SWITCH is set “PROTECED”
03 SD CARD WRITTING ERROR (Memory is full) (ECR cannot write the
data on SD card.)
04 SD CARD READING ERROR (File is nothing)
05 SD CARD READING ERROR (File data is failed) (ECR cannot read
the data on SD card.)
: >
10 Over limitation of data records (Over max record in sales or
EJ data.)
: >
99 SD CARD ERROR (Anyhow error except above SD ERROR is occurred
when ECRaccesses SD Card.)
XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE
3 – 5
-
SHARP CORPORATIONInformation and Communication Systems
GroupQuality Assurance DepartmentYamatokoriyama, Nara 639-1186,
Japan
2006 November Printed in Japan t
COPYRIGHT 2006 BY SHARP CORPORATIONAll rights reserved.Printed
in Japan.
No part of this publication may be reproduced,stored in a
retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or
otherwise,without prior written permission of the publisher.
LEAD-FREE SOLDERCHAPTER 1. MASTER RESET and program reset1.
Master resetting2. Program resetting (Initialization)
CHAPTER 2. PROGRAM MODE1. Reading Stored Programs2. USER
PROGRAMMING3. Character assignment method4. HELP Function
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODEElectronic Journal
Report