© 2017 Cadac Holdings Ltd. Technical specifications and appearances are subject to change without notice and accuracy is not guaranteed. DOC02-Set-up iPad Remote Issue A - May 2017 Quick Reference Guide Cadac Holdings Limited One New Street Luton Bedfordshire LU1 5DX England Tel: +44 1562 404 202 Email: [email protected] www.cadac-sound.com Contact Procedure This is the procedure to set-up the iPad for use with Cadac digital consoles How to Set-Up iPad Remote Control Description
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
© 2017 Cadac Holdings Ltd. Technical specifications and appearances are subject to change without notice and accuracy is not guaranteed.
DOC02-Set-up iPad Remote Issue A - May 2017
Quick Reference Guide
Cadac Holdings Limited One New Street Luton Bedfordshire LU1 5DX England
Tel: +44 1562 404 202 Email: [email protected] www.cadac-sound.com
Contact
Procedure
This is the procedure to set-up the iPad for use with Cadac digital consoles
How to Set-Up iPad Remote Control
Description
Page 2 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
Introduction
This is a guide on how to setup the iPad for use with the CDC eight, CDC seven and CDC six.
This document goes through the process of configuring the console for wireless remote control via the Cadac Remote App on the iPad.
Required
You will require a:
• Wireless Router
• Ethernet Cable
• An Apple iPad with Cadac Remote installed
Note: Search the Apple App Store for “Cadac Remote”
Page 3 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
Procedure to Setup up the Console for iPad Remote Control
To set up the console for iPad remote control you will need to restart the console and follow the
procedure below.
1. When the CDC Loader screen appears press ‘Console Type’:
2. Press ‘Bridge Server’ if the button is not already highlighted in Green:
Page 4 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
3. Press ‘Apply’:
4. The console will then continue to boot.
5. When the console has booted up, press the ‘Menu’ button on the console:
Page 5 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
6. From ‘Settings’ on the 6.5 control screen select ‘Settings’:
7. Press ‘Bridge’:
Page 6 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
8. From the Bridge Server Settings select ‘Network Port’:
9. IMPORTANT: For the next step you MUST plug in the wireless router in the console via and
an Ethernet cable
10. Plug in the Ethernet cable into the back of the console via one of the two NETWORK ports:
Page 7 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
11. Select the active network. It will be either Extern 1 or Extern 2.
NOTE: The active network is the computer icon without the “Red X” (shown below by the
green circle):
12. Now Reboot the console
13. After the console has rebooted go to the ‘About’ screen and check to see if the ‘Bridge
Server’ is active:
Page 8 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
It must display a version number:
NOTE: If only the name ‘Bridge Server’ is being displayed then go back to the start of this
procedure and toggle the “Bridge Server” button on the start-up screen.
14. Go to the Bridge Server Setting (via Settings - Bridge) page and select ‘Remote’:
Page 9 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
15. Select ‘Allow Any’:
16. Open the Cadac Remote App on your iPad.
17. Select you console and wait for connection.
Page 10 of 10
DOC02-Formatting Waves Drive Issue B - Jan 2017
18. After the App has connected select “Remember Me” on the console.
The iPad should now be connected and ready to remotely control the console.
Related Documents
