essure distribution calculations for the PET system and the accelerating structure Costa Pinto P. Recent investigations of TS-MME for the CLIC project, 10 of June 2005 1- The problem 4- Conclusions…and… next? 3- Preliminary results 2- The calculation method 24
18
Embed
Pressure distribution calculations for the PETS system and the accelerating structure
Pressure distribution calculations for the PETS system and the accelerating structure. 1- The problem. 2- The calculation method. 3- Preliminary results. Costa Pinto P. 4- Conclusions…and… next?. 24. Recent investigations of TS-MME for the CLIC project, 10 of June 2005. - PowerPoint PPT Presentation
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Pressure distribution calculations for the PETS system and the accelerating structure
Costa Pinto P.
Recent investigations of TS-MME for the CLIC project, 10 of June 2005
1- The problem
4- Conclusions…and… next?3- Preliminary results2- The calculation method
24
Necessary to calculate the pressure distribution inside the PETS and accelerating cavities and correlate it with pressures read by the gauges.
Possible causes: gas discharges?... Electron bombardment due to field emission?...
RF breakdown in CTF3. Problem:
The accelerating cavity
COMPLEX VACUUM CALCULATIONS
The calculation method
too many differential equations!
Analytical solution:
promising, but long to implementMonte Carlo simulation:
The same differential equations as for the analytical solution… but solved numerically by dedicated software! (PSpice)
Electrical network analogy:
Fast implementation, user friendly, easy to upgrade
The electrical analogy
electric
Flow of gas molecules Flow of electrons
vacuum
dtdQmolecules = q =
C.p dQelectrons
dt= I = G.V
dpdt
q = V. dVdt
I = C.
Pressure p [Torr]
Conductance C [l s-1]Gas flow q [Torr l s-1]
Volume V [l]Potential V [V]
Conductivity G 1]Current I [A]
Capacitance C [F]
The calculation method
electric
Flow of gas molecules Flow of electrons
vacuum
Pressure p [Torr]
Conductance [l s-1]Gas flow [Torr l s-1]
Volume [l]Potential V [V]
Conductivity 1]Current [A]
Capacitance [F]
q1
S1
V1 P1C1G1
I1
q2
S2
V2 P2
C1
2
C2 G2
I2G12
Implementation
Equivalent circuit for a standard celli
x4
Implementation
Circuit for the accelerator structure and half of the wave guide to PETS
Watch me
Preliminary results
Steady state (bias point analysis)
Assumptions: Well baked system with outgassing rate of 2x10-12 Torr.l.s-1.cm-2Gas loads are distributed (current sources)
PETSWave guideAccelerator structure
Ptank
PWG
Ptan
kPWG
Simulation [Torr]
Experimental [Torr]
1.7x10-10
3.5x10-10
3.8x10-9
9.0x10-9
0.49 0.42
OK!
Preliminary results
Transient analysis:Simulation of a pressure burst caused by a spark.
Assumptions: A 40 ns spark in cell 15 induces gas desorption from a region of 100m diameter & 1m deep.gas from 1 monolayer: qm=6.1x10-2 Torr l s-1gas from 5ppm of O in Cu: qO=1x10-1 Torr l s-1
10-10
10-9
10-8
10-7
10-6
10-5
10-4
0 0.2 0.4 0.6 0.8 1
PtankPwgPcell15
P[Torr]
time [s]
10-10
10-9
10-8
10-7
10-6
10-5
10-4
0 0.002 0.004 0.006 0.008 0.01
PtankPwgPcell15
P[Torr]
time [s]10-10
10-9
10-8
10-7
10-6
10-5
10-4
0 0.002 0.004 0.006 0.008 0.01
PtankPwgPcell15Pcell10Pcell1
P[Torr]
time [s]
Preliminary results
Transient analysis:Simulation of successive pressure bursts induced by 40ns sparks at 25Hz repetition rate.Assumptions: Each 40 ns spark in cell 15 induces gas
desorption from a region of 100m diameter & 1m deep.gas from 1 monolayer: qm=6.1x10-2 Torr l s-1gas from 5ppm of O in Cu: qO=1x10-1 Torr l s-1
10-10
10-9
10-8
10-7
10-6
10-5
10-4
0 0.2 0.4 0.6 0.8 1
PtankPwgPcell15
P[Torr]
time [s]
Preliminary results
Transient analysis:Comparison with experimental data.
conditions: Pressure measured by penning gauges and recorded every second.
10-9
10-8
10-7
10-6
0 5000 1 104 1.5 104 2 104
PtankCLICPwgCLIC
P[Torr]
time [s]10-9
10-8
10-7
10-6
0 2 4 6 8 10 12 14
P[Torr]
time [s]
10-8
10-7
-0.5 0 0.5 1 1.5 2 2.5 3
P[Torr]
time [s]
Ptank exp
Ptank sim
Ptank exp
Ptank sim
Conclusions
PSpice is a useful tool to perform transient vacuum calculations using the electrical network analogy.The simulation of the accelerator structure and half of the wave guide give coherent results.
And next?...
Complete the simulation (PETS side, HDS)
Analyze experimental data and find gas loads matching the pressure profiles.
Improve knowledge about the gas released: composition, quantity and time dependence. (increase acquisition rate; install RGA, measure real pumping speed in the tank, calibrated gauges).
Thanks:
C. AchardFor the drawings and the photos of accelerator
structure. F. Tecker
For the pressure data.
Preliminary results
Transient analysis
Typical pressure burst on PTank:
Pmax~1.3x10-7 Torr
Preliminary results
Transient analysis
Gas load of 6x10-6 Torr.l.s-1 for 1 second in cell 15: time
q
max PCell 15~ 3.8x10-6 Torr
max PTank~ 1.3x10-7 Torr
PCell 15
PTank
PCell 15
PTank
~ 30
Preliminary results
PCell 15
PTank
PCell 1
Transient analysis
Gas load of 6x10-6 Torr.l.s-1 for 1 second in cell 15: time