Presented by Composites One in Partnership with IACMI August 9-10, 2016 • Indiana Manufacturing Institute • West Lafayette, IN Workshop Address: Indiana Manufacturing Institute 1105 Challenger Avenue West Lafayette, IN 47906 (765) 494-4437 Please join us for a networking reception and supper by the bite at Purdue University - Ross Ade Pavilion. Ross Ade Pavilion - Shively Club South 850 Beering Drive West Lafayette, IN 47907 (765) 746-5199 P2P Composites is Proudly Sponsored By: P2P Composites is Presented By:
3
Embed
Presented by Composites One in Partnership with IACMI€¦ · · 2016-07-26Presented by Composites One in Partnership with IACMI ... SikaAxson Urethane Vacuum Casting; Sam Gorton,
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Presented by Composites One in Partnership with IACMI
August 9-10, 2016 • Indiana Manufacturing Institute • West Lafayette, IN
Workshop Address:
Indiana Manufacturing Institute1105 Challenger AvenueWest Lafayette, IN 47906
(765) 494-4437
Please join us for a networking reception and supper by the bite at Purdue University - Ross Ade Pavilion.
Ross Ade Pavilion - Shively Club South 850 Beering Drive
West Lafayette, IN 47907(765) 746-5199
P2P Composites is Proudly Sponsored By:
P2P Composites is Presented By:
Tuesday, August 9
8:00 a.m. Welcome: Leon Garoufalis, President and COO, Composites One; Dr. R. Byron Pipes, John L. Bray - Distinguished Professor of Engineering, Purdue University; and IACMI Technology Area Director
8:30 a.m. Virtual Composites: The Value of Modeling and Simulation to Fabricators The Composites Virtual Factory HUB (cvfHUB): Simulating Composites Processes Presented By: Dr. R. Byron Pipes, John L. Bray - Distinguished Professor of Engineering, Purdue University; and IACMI Technology Area Director Composite Part Design & Modeling Tool Box for Rapid Application Development Presented By: Dr. Amol Vaidyam, Global Innovation Leader, Owens Corning and Dr. Gajendra Pandey, Senior Engineer, Owens Corning Using Laminate Design and Analysis Software for Optimized Composites Structures Presented By: Trevor Gundberg, P.E., Director of Composites Engineering , Vectorply Corp
9:30 a.m. Session Previews Session 1: Vacuum Infusion Presented By: Neil Smith, Technical Support Manager, Composites One; Russ Elkin, Senior Technical Service Engineer, 3A Baltek; Trevor Gundberg, Director of Composites Engineering, Vectorply; and Jeff Wright, Technical Director, Gougeon Brothers, Inc. Location : Raisbeck Engineering Composites Laboratory Session 2: Reusable Vacuum Bags for Vacuum Infusion Presented By: Jim Noonan, Technical Support Manager, Composites One and Larry Audette, President, SWORL Location : Wet Layup Lab
Session 3: Advances in Tooling Presented By: Dan Alter, Advanced Composites Sales Specialist, Composites One; Brent Schubring, Strategic Account and Business Development Manager, SikaAxson Urethane Vacuum Casting; Sam Gorton, Market Development Manager, Soul Composites - GURU Rapid Tooling; and Vlastimil Kunc, Group Leader, Polymer Materials Development, ORNL Location: CNC Lab and Additive Manufacturing Lab
Session 4: Composite Testing and Characterization Presented By: Dr. Johnathan Goodsell, Director of Validation, Composites Manufacturing and Simulation Center, Purdue University Location: Composites Characterization Lab
10:00 a.m. MORNING CONCURRENT SESSIONS
11:00 a.m. 15 Minute Break
12:15 p.m. Luncheon Speaker Labor-less Prototype Tooling Leigh Sargent, President and Founder of Applied Composites Engineering
Your Workshop Agenda
Morning Session 110:00 a.m. - 11:00 a.m.
Morning Session 211:15 a.m. - 12:15 p.m.
AfternoonSession 11:30 p.m. - 2:30 p.m.
AfternoonSession 22:45 p.m. - 3:45 p.m.
Group 1
Group 2
Group 3
Group 4
1:30 p.m. AFTERNOON CONCURRENT SESSIONS
2:30 p.m. 15 Minute Break
4:00 p.m. Equipping Yourself for Success Presented By: Andrew Hedger, Product Line Manager of Closed Molding, Magnum Venus Products
4:30 p.m. Day 1 Wrap Up Review / Q&A and Review Day 2 Agenda
6:00 p.m. Networking Reception: Join us for a networking reception and supper by the bite at Purdue University - Ross Ade Pavilion. Ross Ade Pavilion - Shively Club South 850 Beering Drive West Lafayette, IN 47907 (765) 746-5199
Wednesday, August 10
8:00 a.m. Welcome and Review Agenda
8:15 a.m. How To Use the Resources at IACMI and Indiana Manufacturing Institute Presented By: Ronald Steuterman, Managing Director, IN-MaC & Purdue IACMI
8:30 a.m. Infrastructure Case Study: Adhesively Bonded Composite Wharfs and Docks for Hurricane Cat 3 Conditions Presented By: Stuart La Haise, Sales Representative, Engineered Bonding Solutions
9:00 a.m. Session Previews for Day 1
Session 5: Prepregs and Thermoplastic Fibers for Compression Molding Presented By: Joe Pantalone, Advanced Composites Product Manager, Composites One; Will Ricci, Technical - Americas, Gurit; and Al Hollenbeck, Chief Operating Officer, Concordia Fibers Location: Molding Lab
Session 6: LRTM Production Molding Cell Presented By: Doug Smith, President, RTM North; Travis Irvin, Sales Manager, Chomarat; Rick Pauer, Applications Manager, Polynt; and Sam Dethloff, Aerospace & Composites Industry Technical Manager, Chem-Trend Location : Raisbeck Engineering Composites Laboratory
9:30 a.m. MORNING CONCURRENT SESSIONS
10:30 a.m. 15 Minute Break
11:45 a.m. Day 2 Wrap Up Review and Q&A
12:00 a.m. Lunch
Tuesday, August 9
8:00 a.m. Welcome: Leon Garoufalis, President and COO, Composites One; Dr. R. Byron Pipes, John L. Bray - Distinguished Professor of Engineering, Purdue University; and IACMI Technology Area Director
8:30 a.m. Virtual Composites: The Value of Modeling and Simulation to Fabricators The Composites Virtual Factory HUB (cvfHUB): Simulating Composites Processes Presented By: Dr. R. Byron Pipes, John L. Bray - Distinguished Professor of Engineering, Purdue University; and IACMI Technology Area Director Composite Part Design & Modeling Tool Box for Rapid Application Development Presented By: Dr. Amol Vaidyam, Global Innovation Leader, Owens Corning and Dr. Gajendra Pandey, Senior Engineer, Owens Corning Using Laminate Design and Analysis Software for Optimized Composites Structures Presented By: Trevor Gundberg, P.E., Director of Composites Engineering , Vectorply Corp
9:30 a.m. Session Previews Session 1: Vacuum Infusion Presented By: Neil Smith, Technical Support Manager, Composites One; Russ Elkin, Senior Technical Service Engineer, 3A Baltek; Trevor Gundberg, Director of Composites Engineering, Vectorply; and Jeff Wright, Technical Director, Gougeon Brothers, Inc. Location : Raisbeck Engineering Composites Laboratory Session 2: Reusable Vacuum Bags for Vacuum Infusion Presented By: Jim Noonan, Technical Support Manager, Composites One and Larry Audette, President, SWORL Location : Wet Layup Lab
Session 3: Advances in Tooling Presented By: Dan Alter, Advanced Composites Sales Specialist, Composites One; Brent Schubring, Strategic Account and Business Development Manager, SikaAxson Urethane Vacuum Casting; Sam Gorton, Market Development Manager, Soul Composites - GURU Rapid Tooling; and Vlastimil Kunc, Group Leader, Polymer Materials Development, ORNL Location: CNC Lab and Additive Manufacturing Lab
Session 4: Composite Testing and Characterization Presented By: Dr. Johnathan Goodsell, Director of Validation, Composites Manufacturing and Simulation Center, Purdue University Location: Composites Characterization Lab
10:00 a.m. MORNING CONCURRENT SESSIONS
11:00 a.m. 15 Minute Break
12:15 p.m. Luncheon Speaker Labor-less Prototype Tooling Leigh Sargent, President and Founder of Applied Composites Engineering
Your Workshop Agenda
1:30 p.m. AFTERNOON CONCURRENT SESSIONS
2:30 p.m. 15 Minute Break
4:00 p.m. Equipping Yourself for Success Presented By: Andrew Hedger, Product Line Manager of Closed Molding, Magnum Venus Products
4:30 p.m. Day 1 Wrap Up Review / Q&A and Review Day 2 Agenda
6:00 p.m. Networking Reception: Join us for a networking reception and supper by the bite at Purdue University - Ross Ade Pavilion. Ross Ade Pavilion - Shively Club South 850 Beering Drive West Lafayette, IN 47907 (765) 746-5199
Wednesday, August 10
8:00 a.m. Welcome and Review Agenda
8:15 a.m. How To Use the Resources at IACMI and Indiana Manufacturing Institute Presented By: Ronald Steuterman, Managing Director, IN-MaC & Purdue IACMI
8:30 a.m. Infrastructure Case Study: Adhesively Bonded Composite Wharfs and Docks for Hurricane Cat 3 Conditions Presented By: Stuart La Haise, Sales Representative, Engineered Bonding Solutions
9:00 a.m. Session Previews for Day 1
Session 5: Prepregs and Thermoplastic Fibers for Compression Molding Presented By: Joe Pantalone, Advanced Composites Product Manager, Composites One; Will Ricci, Technical - Americas, Gurit; and Al Hollenbeck, Chief Operating Officer, Concordia Fibers Location: Molding Lab
Session 6: LRTM Production Molding Cell Presented By: Doug Smith, President, RTM North; Travis Irvin, Sales Manager, Chomarat; Rick Pauer, Applications Manager, Polynt; and Sam Dethloff, Aerospace & Composites Industry Technical Manager, Chem-Trend Location : Raisbeck Engineering Composites Laboratory