Page 1
1
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
INJECTOR-TEST
AAE060-0H HAND TEST INJECTOR – POP TESTER.
Similar Bosch 0.681.200.502
Our hand test injectors consist of:
• Manometer 0-400 or 0-600 Bar in Bar and
in PSI;
• Standard pipes 14x14 and 12x12;
• Manual level;
• Filter;
• Tank;
• Measure: mm 415 x 540 x 130,
• Weight: kg. 7,00.
AAE060-0A SUCHTION DEVICE
Similar Bosch 0.684.200.702
AZ0138-00 QUICK CONNECTION
Quick connection for hand-test injector.
Thread 12x1,5mm.
Thread 14x1,5mm.
Page 2
2
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AZ0134-AS250 TESTER
RESISTANCE / INDUCTANCE
Particular tester to check RESISTANCE and
INDUCTANCE of common rail injectors.
(Especially for Piezo and VDO).
It is recommend to check always the injectors
before to connect it to any kind of tester/simulator to
avoid the risk that the injectors could burn with a
short-circuit the system/board.
AZ0134-HI TESTER INSULATION
Particular tester to check INSULATION of common
rail injectors.
(Especially for Piezo and VDO)
It is recommend to check always the injectors
before to connect it to any kind of tester/simulator to
avoid the risk that the injectors could burn with a
short-circuit the system/board.
INJECTOR-TEST
Page 3
3
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AZ0222-CRR TESTER AND FEEDER FOR COMMON RAIL INJECTOR
Our tester AZ0222-CRR permits the following tests:
a) To check the electrical part of all kind of common rail injectors (Bosch, Delphi, Denso and VDO –
Electromagnetic and Piezo). ELECTRICAL TEST
b) To check the spray of the injectors; if the injector is connected to an hand-test injector. SPRAY TEST
c) If you connect the injector to a compartor bearing with comparator it permits to check and see the ball-
lift of common rail injectors Bosch Electromagnetic CRI and CRIN. BALL-LIFT TEST
d) If you connect the injector to a compartor bearing with comparator it permits to check and see the
dynamic-lift of the Stack (Solenoid) of VDO injectors. DYNAMIC-LIFT STACK VDO TEST
a) ELECTRICAL TEST
The tester AZ0222-CRR includes 5 cables to connect to the instrument the different models of injectors
(Bosch, Delphi, Denso, VDO etc).
The electrical test permits to get the following results:
1. Acoustic Feed-back produced by the injector dued to the impulses induced by the instrument.
2. Electical absorption in Ohm (0.00 Ω).
-ABSORPTION MEASURED IN HUNDREDTH OF OHMS (0.00 Ω).
Attention:
Classic multimeters measure the absorption in tenth of Ohm (0.0 Ω).
INJECTOR-TEST
Page 4
4
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
b) SPRAY TEST
The tester AZ0222-CRR, if connected to an inejctor joint with an hand-test injectors manual or automatic,
permits to check and see the spray of the injector.
In this way it permits to control the pulverizer (nozzle).
The tests available on the AZ0222-CRR simulate the test of a test bench with common rail simulator.
The window is user-friendly
The are nr. 2 type of tests: ”TIME” or “PULSE”.
Tests:
a) MAIN INJECTION
b) PRE-INJECTION
c) PILOT INJECTION
All the test-parameters are set by the producer; however it is possible to enter inside the software and to
modify the values also when the test has already began.
The parameters checked and modifiable are:
1. Frequency “Hz”
2. Opening time “ms”
3. Power “V”
c) BALL-LIFT TEST
d) DYNAMIC-LIFT TEST STACK VDO
To control the ball-lift and/or the dynamic lift of VDO Stack is necessary to connect the injector to a
comparator bearing and than connect the injector to the tester.
You will see the measure of the ball-lift on the comparator.
Optional comparator bearing:
AZ0352-CR
AAZ006-KIT AZ0352-CR
AAZ006-KIT
INJECTOR-TEST
Page 5
5
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
COMMON RAIL INJECTOR TESTER - SABRE
SABRE CRi MASTER
COMPACT ALL MAKERS COMMON RAIL INJECTOR TESTER
Fast: typically 1 minute per test step
High accurate testing and stability
Simplified and fast injector clampling/changeover
Advanced magmah user interface
Very easy installation
The tester can work automatically or manually
Plan can be modified
Windows 10 Magmah (sharp) with touch-screen
Wi-fi
With 3 air-to-oil heat exchangers to regulate and stabilise temperatures ensuring test-to-test and machine-to-
machine repeatability.
Patented technology
Electrical connection required: 200-240Vca (10/16 Amp) – Domestic mains connection-
SABRE CRi MASTER
TECHNICAL SPECIFICATION
Rail Pressure 0-1800 bar
Injection Speed 120-3000 ipm
Pulse Width 0-4000 µS
Time Delay 0-600 seconds
Coil resistance 0-200 Ω
Inductance 0-20 mH
Capacitance 0-12 µF
Reponse time meas. 0-999 µS
INJECTOR-TEST
Page 6
6
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
INJECTOR CODING – S1000
S1000 THE UNIQUE SOFTWARE TO CREATE CODES FOR COMMON RAIL INJECTORS.
Easy and fast software to codify common rail injectors
Compatible with the following test-bench:
EPS 815 – EPS 708 – EPS205 – AVM2pc – CRIpc – SABRE
Compatible also with other test-benches of different brands depending on the accuracy of the system of
measure of the quantity.
AUTHORIZED DISTRIBUTOR
INJECTOR-TEST
Page 7
7
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
INJECTOR-TEST – HEUI -
INJECTOR TESTER FOR HEUI - TOLEDO
TOLEDO HEUi MASTER
ADVANCED COMPACT ALL-MAKES TESTER FOR HEUi
New patented Technology
Windows 10 Magmah (sharp) with touch-screen
Simplified and fast injector clampling/changeover
Comprehensive HEUi Parc Coverage
Electical mains connections required : 200-240Vca (10/16 Amp) - domestic-
Compact, Easy installation and user-friendly
With testing-table
Optional: 7 kit of adaptors for different type of injectors.
Heui Injectors: Ford Powerstroke 4.5L V6, 6.0L V8, 7.3L V8.
Navistar DT444E 7.3L – DT446E 7,6L – DT530E 8.7L
Navistar DT570 & HT570 9.3L – VT275 4.5L – VT365 6.0L
CAT 3408 18.0L – 3412 27.0L – 3116E 6.6L – 3126A 7.2L
CAT 3126B 7.2L – C7 7.2L – C9 8.8L
Isuzo 4JX1 3.1L
TOLEDO HEUi MASTER
TECHNICAL SPECIFICATION
Intensifier Pressure Control 20-280 bar
Injected Fuel Press. Control 3 bar (fixed)
Injection Speed 120-1300 ipm
Pulse Width 100-4000 µS
Injector coil resistance 0-200 Ω
Inductance 0-20 mH
Response time meas. 0-999 µS
Page 8
8
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
ELECTRICAL CONNECTORS
AAZ023-B11
Electrical connector with wire – 2 pins –
For injector Delphi
AAZ023-758C
Electrical connector (WITHOUT wire) – 2 pins –
For injector Delphi
AAZ023-B13
Electrical connector with wire– 2 pins –
For injector Delphi 1.5
AAZ023-858C
Electrical connector (WITHOUT wire)– 2 pins –
For injector Delphi 1.5
AAZ023-B10
Electrical connector with wire– 2 pins –
For injector Bosch
AAZ023-933C
Electrical connector (WITHOUT wire)– 2 pins –
For injector Bosch
INJECTOR-TEST
Page 9
9
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AAZ023-756
Electrical connector with wire– 2 pins –
For injector Bosch
AAZ023-756C
Electrical connector (WITHOUT wire) – 2 pins –
For injector Bosch
Similar: 9001-925
AAZ023-B01
Electrical connector with wire– 2 pins –
For injector Denso & DRV
AAZ023-B02
Electrical connector with wire– 2 pins –
Universal use
AAZ023-B03
Electrical connector with wire– 3 pins –
For sensor of pressure rail Denso and Pressure Regulator VDO
X-39-800-300-005Z
INJECTOR-TEST
ELECTRICAL CONNECTORS
Page 10
10
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AAZ023-B04
Electrical connector (WITHOUT wire)– 4 pins –
Bosch – (Fiat Multijet – Doblò)
AAZ023-B05
Electrical connector with wire– 3 pins –
For sensor of pressure rail Denso
AAZ023-B06
Electrical connector with wire– 2 pins –
For injector Denso (Mitsubishi L200)
AAZ023-B07
Electrical connector with wire– 2 pins –
For injector EUI Delphi (Volvo EUI)
INJECTOR-TEST
ELECTRICAL CONNECTORS
Page 11
11
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AAZ023-B08
Electrical connector with wire– 4 pins –
For injector EUI Delphi (Volvo EUI)
AAZ023-B09
Electrical connector with wire– 2 pins –
Bosch
AAZ023-B12
Electrical connector with wire– 3 pins –
For sensor of pressure rail Bosch
INJECTOR-TEST
ELECTRICAL CONNECTORS
Page 12
12
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AZCBCR-4-SIM COMMON RAIL SIMULATOR
Common rail simulator to check injectors (Bosch, Delphi, Denso and VDO Elettromagnetic and Piezo) at the
test bench.
Our simulator is sold with KIT RAIL (AAZ034-KIT) to assemble the injector to the test bench.
1. It tests till 4 injectors at the same time.
2. It tests the quality of the bobbin (resistance and power of the magnet/Piezo).
3. With testing-table for injectors
4. If connected to a comparator bearing (ex. AZ0352-CR and/or AAZ006-KIT) it permits to measure the
ball-lift and/or the dynamic-lift of stack VDO.
5. It produces and controls automatically and/or manually the pressure
6. It can do the following tests:
a) Electrical test
b) Opening test (NOP)
c) Leaking test (LEAK TEST)
d) Quantity test (VE-LL-EM-VL)
7. It can check also common rail PUMP
a) It drives pressure regulators and valves
b) Testing-tables for Bosch pumps
AZCBCR-4-SIM can be assembled on every kind of test bench. It is not necessary a particular power of the
test bench (KW).
INJECTOR-TEST
Page 13
13
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AAZ034-KIT KIT RAIL TO ASSEMBLE NR. 4 INJECTOR
ON THE TEST BENCH.
The code AAZ034-KIT is included in our simulator AZCBCR-4-
SIM.
Kit rail AAZ034-KIT is sold also individually.
Here below the items included in the code AAZ034-KIT:
AAZ034-KIT KIT RAIL
AAZ034-11 RAIL
AAT099-CR2 RILSAN PIPE
In the kit AAZ034-KIT nr. 4 rilsan pipe
AAZ034-09L QUICK CONNECTION «L» SHAPED
In the kit AAZ034-KIT nr. 4 quick conenction «L» shaped
INJECTOR-TEST
Page 14
14
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AAZ010-10AN DUMPERS X TEST BENCH
In the kit AAZ034-KIT nr. 8 dumpers
BR0001-00 CONNECTION RAIL – INJECTOR14X14M
In the kit AAZ034-KIT nr. 7 connections
AAZ034-12 CAP M14
In the kit AAZ034-KIT nr. 6 caps
AAZ034-11A KIT OF 2 ADJUSTABLE SUPPORTS TO FIX THE
RAIL
In the kit AAZ034-KIT nr. 1 kit
AAZ034-12A PROTECTION KIT
In the kit AAZ034-KIT nr. 1 kit
AAZ034-10A KIT OF NUTS AND BOLTS TO FIX THE RAIL
In the kit AAZ034-KIT nr. 1 kit
INJECTOR-TEST
Page 15
15
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
AAZ034-13 FALSE PRESSURE REGULATOR BOSCH
In the kit AAZ034-KIT nr. 1 false regulator
BR0007-00 + BR0006-00
Nr. 1 BR0007-00 + Nr. 7 BR0006-00
AAT000-FX FLEXIBLE PIPE 6X2X600 14X14
Similar 1.680.750.000
In the kit AAZ034-KIT nr. 1 pipe
AAT005-00 FLEXIBLE PIPE 6X2X300 14X14
In the kit AAZ034-KIT nr. 4 pipes
AAZ010-31 CONNECTION X HIGH PRESSURE PIPES 12FX14M
Similar 1.680.750.000
In the kit AAZ034-KIT nr. 5 connections
AAZ034-19 ADAPTOR FOR PRESSURE REGULATOR
PUMP BOSCH - BIG-
In the kit AAZ034-KIT nr. 1 adaptor
AAZ034-20 ADAPTOR FOR PRESSURE SENSOR OF PUMP
BOSCH/VDO
In the kit AAZ034-KIT nr. 1 adaptor
INJECTOR-TEST
Page 16
16
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
OPTIONAL X SIMULATOR AZCBCR-4-SIM
AZCBCR-RSP RSP SENSOR
Sensor for common rail simulator AZCBCR-4-SIM.
Response time measurements.
INJECTOR-TEST
Page 17
17
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
INJECTOR-TEST UI-UP
CAM-BOX FOR UNIT INJECTOR
AZCBCR-CB SIMULATOR CAM-BOX FOR INJECTOR UI-UP
Tester to control injectors UI-UP.
The simulator can be connected on every kind of mechanic cam-box base.
The AZCBCR-CB permits the following tests:
Quality of the bobbins.
To test on the test-bench unit-injector electromagnetic and piezo.
It measures the BIP moment, If connected with our optional RSP sensor.
It permits to test Delphi 2 and 4 PIN.
With testing-table.
With all the cables
To be used on a test-bench with mechanical cam-box (AZ0134-CB-NUDO).
Page 18
18
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
CAM-BOX FOR UNIT INJECTOR
AZ0134-CB-NUDO CAM-BOX BASE FOR INJECTOR UI-UP
Cam-Box base to lay on the test bench to test injectors UI and UP.
Cam-box is universal and can be fixed on every diesel test bench; the height of our cam-box, from the base to
the camme is the same as Bosch equipment: 125mm. In case there was a test bench with a different height
you need only to buy one of our adaptor-plate.
The cam-box base AZ0134-CB-NUDO permits to test injector VOLVO and some models of IVECO. To test
all the differend kind of unit-injectors we offer the following ADAPTORS KIT:
AZ0134-CB-SCANIA
AZ0134-CB-DETROIT TYPE 5235580/570 (Special version for both types)
AZ0134-CB-CUMMINS
AZ0134-CB-ACTROS MERCEDES
AZ0134-CB-ATEGO
AZ0134-CB-DAF
AZ0134-CB-CATERPILLAR L 10
AZ0134-CB-CATERPILLAR L 15
AZ0134-CB-500HP DELPHI
AZ0134-CB-JOHN DEERE DELPHI
AZ0134-CB-IVECO CURSOR 350 CV *
AZ0134-CB-LAND ROVER / DISCOVERY*
AZ0134-CB-VOLKSWAGEN*
* Our CAM-BOX has nr. 2 cam-shafts (one is included in AZ0134-CB-NUDO) h. 8mm and h. 11,5mm.
It is possible to buy only the ADAPTORS you need.
INJECTOR-TEST UI-UP
Page 19
19
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
ADAPTORS KIT FOR CAM-BOX
INJECTOR-TEST UI-UP
Page 20
20
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
INJECTOR-TEST UI-UP
ADAPTORS KIT FOR CAM-BOX
Page 21
21
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
OPTIONAL X SIMULATOR AZCBCR-CB
AZCBCR-RSP-CB RSP SENSOR
Sensor for simulator cam-box AZCBCR-CB
Response time measurements.
INJECTOR-TEST UI-UP
ADAPTORS KIT FOR CAM-BOX
Page 22
22
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
BEEPER
AZBEEPER-00 TESTER TO MEASURE BIP MOMENT –UNIVERSAL – INJECTOR UI-UP
System to read the BIP signal for the most part of cam-box simulators (EUI) of old generation on the market.
It permits to measure the BIP moment. The time of response of the injector (EUI).
UNIVERSAL – FOR THE MOST PART OF CAM-BOX SIMULATOR
INJECTOR-TEST UI-UP
Page 23
23
All rights reserved to: SIRINI Srl – Via Lombardia 17 - 20010 Arluno – Milano – Italy
Tel. +39 02 90376944 – Fax: 02 903 76514 e.mail: [email protected] - Sirini is an Original Trade Mark
SIMULATOR COMMON RAIL + SIMULATOR CAM-BOX
AZCBCR-4-SIM-CB SIMULATOR COMMON RAIL AND CAM-BOX
Simulator that combines the functionality of our simulators AZCBCR-4-SIM and AZCBCR-CB.
The software of this simulator permits to test:
common rail injectors Bosch, Delphi, VDO and Denso Elettromagnetic and Piezo
common rail pumps
Unit-injectors UI-UP
The simulator includes also our kit rail, AAZ034-KIT, to assemble common rail injector on the test bench.
Optional:
AZ0134-CB-NUDO CAM-BOX base
ADAPTORS KIT FOR CAM-BOX
RSP sensors
INJECTOR-TEST UI-UP