09 操作手册 Surgical Technique Gamma Locking Nail System OPERATIVE TECHNIQUE PRE-OPERATIVE PLANNING X ,以及用C-臂X , , X 36 10%〜15%。 A/P and lateral C-arm images should be obtained prior to the surgical procedure. The suitability of this implant for the patient should be determined prior to surgery by read the X-ray of the affected femur. An A/P preoperative X-ray should be taken of the contra lateral hip or of the affected limb once an anatomic reduction has been achieved. X-rays taken at a 36-inch distance from the source result in 10-15 percent magnification of the bone.
35
Embed
PRE-OPERATIVE PLANNINGSurgical Technique REDUCTION, ,, It is critical to reduce the fracture before beginning the surgical procedure. An anatomic reduction or a slight valgus reduction
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
09
操作手册Surgical Technique
Gamma Locking Nail System
OPERATIVE TECHNIQUE
PRE-OPERATIVE PLANNING
X ,以及用C-臂X ,
, X 36
10%〜15%。
A/P and lateral C-arm images should be obtained prior to the surgical procedure. The
suitability of this implant for the patient should be determined prior to surgery by read the
X-ray of the affected femur. An A/P preoperative X-ray should be taken of the contra lateral
hip or of the affected limb once an anatomic reduction has been achieved. X-rays taken at
a 36-inch distance from the source result in 10-15 percent magnification of the bone.
10
Gamma Locking Nail System
操作手册Surgical Technique
患者体位PATIENT POSITIONING
, ,方
,
The patient may be placed in either the supine or the lateral decubitus position. In multiple
trauma patients, the supine position may be used for easier access to the airways as well
as to facilitate the treatment of other injuries. The supine position also facilitates fracture
reduction and rotational alignment of the femur. The disadvantage to the supine position
is that it impairs access to the tip of the greater trochanter for insertion of the nail.
, X ,
,
( 1)。
In order to assist in implants placement, it is essential to obtain excellent quality A/P and
lateral images of the entire femoral head and neck prior to beginning the surgery. It is
essential to obtain excellent A/P and lateral images of the femoral head and neck prior to
beginning the surgery regardless of which patient position is used (Fig.1).
1Fig.1
11
操作手册Surgical Technique
Gamma Locking Nail System
患者体位 ( )PATIENT POSITIONING (CONTINUED)
X ,
, ,
, ( 2)。
The use of image intensification or other x-ray imaging is required. The image intensifier
should be sterile-draped and may be positioned from either the contralateral or ipsilateral
side of the operating table. Confirm visualization of the hip as well as the shaft of the
femur using image intensification before prepping and draping. Bend the patient’s torso
away from the affected extremity to improve access to the greater trochanter. If access to
the greater trochanter is still inadequate, adduct the affected leg. However, to achieve
proper alignment of the fracture, this adducted position must be corrected prior to
insertion of the nail (Fig.2).
2Fig.2
12
操作手册Surgical Technique
REDUCTION
, ,
,
It is critical to reduce the fracture before beginning the surgical procedure. An anatomic
reduction or a slight valgus reduction of the femoral head and neck, should be seen in the
A/P film. Occasionally, a slight sag of the fracture may be seen on the lateral view. This
should be taken into consideration during the surgical procedure. This is most important
for consideration of the starting point of the Steinmann Pins or Pointed Awl into the
Femoral head.
Gamma Locking Nail System
13
操作手册Surgical Technique
INCISION AND EXPOSURE
取大粗隆上方1cm , 5cm, ( 3)。
Begin the skin incision 1 cm proximal to the tip of the greater trochanter, and extend it
proximally for about 5 cm in a longitudinal direction. Continue the incision down through
the subcutaneous tissues and split the iliotibial band (Fig.3).
Gamma Locking Nail System
3Fig.3
14
操作手册Surgical Technique
INSERTION SITE
用C-臂X ( 4),
Place the Pointed Awl at the selected starting point (Fig.4) and
confirm its position in both the A/P and lateral planes on C-arm.
Advance the Awl through the greater trochanter to the lesser
trochanter location.
, ,将 (φ2.5*300)
( 5),使用C-臂X
Locating the correct entry portal in the femur is extremely important. The insertion site for
the nail is usually located at the tip of the greater trochanter. Place the Threaded Guide
Pin (φ2.5*300) at the selected starting point(Fig.5), and confirm its position in both the
A/P and Lateral planes on C-arm.
,
4~5cm, , ,
使用硬 (φ8)
( 6)
Check the position with the C-arm.
Advance the pin down into the
medullary canal approximately
4~5cm. Confirm the position of the
pin using the C-arm with A/P and
lateral views. Remove the Threaded
Guide Pin. Use the Rigid Reamer (φ8)
ream the trochanteric region to open
the medullary canal (Fig. 6). Remove
the Reamer.
4Fig.4
5Fig.5
6Fig.6
Gamma Locking Nail System
15
操作手册Surgical Technique
GUIDE WIRE PLACEMENT
将 (φ3*900)插入 ( 7),
,
C-臂X
On the back table, attach the Guide Wire with
Olive(φ3*900) to the Gripper, and tighten (Fig.7). The
tip of the Guide Wire may be bent, to facilitate
fracture reduction. Insert the Guide Wire through the
entry hole and manipulate it down the proximal femur
across the fracture site. At the fracture site,
manipulate the Guide Wire under C-arm control across
the fracture site.
, ( 8)。如果
, ,
位。
Once in the distal canal, pass the wire to the distal
epiphyseal scar (Fig.8). If reduction of the abducted and
flexed hip is difficult, place pressure on the proximal
fragment, either with the hand or directly with a reduction
rod or other instrument.
,
Once the guide wire with Olive has been fully inserted, the
Gripper is removed.
7Fig.7
8Fig.8
Gamma Locking Nail System
16
操作手册Surgical Technique
9Fig.9
REAMING PROCEDURE
切口近端放置 ,
The Soft Tissue Protector is now positioned at the proximal end of the incision to protect
the soft tissue, and secured with tape or a skin clamp.
, ,
X , ,一般从
7.5mm ( 9) 9mm之前, 0.5mm ,之后,
1.0mm , 1〜2 , ,粗
14mm
The medullary canal is now reamed by passing reamer over the Guide Wire. Each reamer is
composed of a Flexible Reamer Head, a Flexible Shaft and a quick-connect drive end. The
quick-connect end can be connected to a powered driver. The width of the isthmus of the
medullary canal is determined by preoperative x-ray examination. The instrument with the
smallest possible diameter is used for initial reaming into the medullary canal, always
starting with the 7.5mm reamer (Fig.9). Reaming should be continued in 0.5 mm
increments before the medullary canal is reamed to 9mm. After that, the reaming should
be continued in 1.0mm increments, Over-reaming the canal by one or two millimeters may
facilitate preparation of the bone to accommodate the implant. The trochanteric region
should be reamed to14mm in diameter in hard bone to accommodate the implant, using
the Rigid Reamer. Use caution in advancing the Rigid Reamer.
注意: ,以及股骨干的最小直径和股骨的的弯曲度。
, ,
Note: Reaming amounts will depend on the quality of the bone
present, the minimum diameter of the femoral shaft, and the
amount of femoral curvature present. Reaming should be
immediately stopped and the reamer retracted when there is too
much resistance. If the reamer becomes lodged, stop reaming
immediately. Reverse the direction of rotation of the handpiece
and back the reamer out of the canal.
Gamma Locking Nail System
17
操作手册Surgical Technique
( )REAMING PROCEDURE (CONTINUED)
, , ,插入普通
(φ3*900) , ,
The plastic Guide Wire Exchange Tube is inserted over the Guide Wire with Olive, so
that it is well across the fracture site. Holding the tube in place, the Guide Wire with Olive
is now removed, and the Guide Wire (φ3*900) is inserted. After confirming that the tip of
the Guide Wire is in the correct position, the plastic tube is removed for insertion of the
cannulated nail.
Gamma Locking Nail System
18
操作手册Surgical Technique
10Fig.10
11Fig.11
12Fig.12
NAIL INSERTION
, 手柄上( 10),并用SW5
手
Select the appropriate size Nail. The nail must be rotated until
it seats into the correct position of the Nail Support Handle
and the Locking Rod is then firmly tightened into the
nail(Fig.10), completing this with the SW5 Wrench.
,
度( 11)。理想的状况下, ,
The nail is now manually inserted over the Guide Wire into the medullary canal until the
nail is seated at the desired depth, under image intensification (Fig.11). This indicates
that the nail has been inserted to the correct depth. Ideally, the nail should be inserted
by hand. If insertion can not be achieved by hand, gentle tapping may be necessary.
将打入(拔出)器 ,
( 12)
The Sliding Hammer maybe attached to the end of the nail Locking Rod, and it must be
tightened fully to avoid damage to the thread. The nail can then be inserted into the
correct position by gentle hammering (Fig.12). Don’t persist if the nail is not advancing,
remove it and ream some more.
注意:
Note:Remove the Guide wire
prior to drilling holes and insert
the Locking Screws.
Gamma Locking Nail System
19
操作手册Surgical Technique
13Fig.13
PROXIMAL LOCKING
, ,
, ,
Before locking with the Lag screws, attention should be paid that the femoral head has
been properly reduced.If the anatomical reduction cannot be achieved with the closed
technique, especially concerning malrotation of the femoral head and neck fragment. The
incision for the Lag screws should be enlarged, such that a forceps can be used for
reduction.
C-臂X ,并使用 和
(φ2.5*300)
The projected path of the Lag Screw into the Femoral Head should be assessed using the
C-arm. This may be verified using the Targeting Device and the Threaded Guide
wire(φ2.5*300).
,并用 (φ9)的 (φ11/φ9)
, , ,
套推向骨面( 13) (φ9/φ2.8)。
The Targeting Device is mounted on the Nail Support
Handle. The Targeting Device Locking Screw is inserted
into the appropriate holes. It is then locked in this position.
The Screw Guide(φ11/φ9) with inserted Obturator (φ9) is
introduced into the distal Lag Screw targeting hole of the
Proximal Guide Bar. The skin is incised at the appropriate
site, and the Lateral cortex exposed by blunt dissection
using the Obturator. And then pushed the Screw Guide
forward up to the bone (Fig.13). Remove the Obturator and
insert the Guide wire sleeve (φ9/φ2.8) through the Screw
Guide.
Gamma Locking Nail System
20
操作手册Surgical Technique
15Fig.15
14Fig.14
( )PROXIMAL LOCKING (CONTINUED)
(φ2.5*300) (φ9/φ2.8), 2mm( 14)。需
, 要
,可以使用打入(拔出器) ,再用C-臂X
也
The Treaded Guide wire(φ2.5*300), is inserted through
the Guide wire sleeve. The guide wire should be
inserted up to about 2mm before the cortex of the
femoral head(Fig.14). The correct position of the guide
wire needs to be checked in the axial view using the
image intensifier. The wire needs to be parallel to the
femoral neck axis and should pass through the center
of the femoral head. If the nail anteversion requires
adjustment, move the nail up or down the canal by
gently impacting using the Sliding Hammer until the
correct depth is achieved. Check the position of the nail
with the C-arm. Adjusting nail depth may be useful in
accommodating various femoral neck anatomies.
用 ( 15)
,
下, 10mm。
Next, the length of the inserted guide wire is
measured with the Lag Screw Depth Gauge for Lag
screws (Fig.15). The Depth Gauge for Lag screws
measures the actual length of the guide wire in the
bone. If the tip of the guide wire was inserted into the
subcortical bone, a Lag screw approximately 10mm
shorter must be chosen.
Gamma Locking Nail System
21
操作手册Surgical Technique
16Fig.16
( )PROXIMAL LOCKING (CONTINUED)
(φ9) (φ11/φ9) , ,取出
(φ9/φ2.8), ( 16)。
For the proximal Lag screw, the skin is opened at the entry point. The Screw Guide
(φ11/φ9) with inserted Obturator(φ9) is intro-duced into the proximal targeting hole of the
Proximal Guide Bar and pushed forward until reaching the bone. The trocar is replaced by
the Guide wire sleeve (φ9/φ2.8). Next, the second Guide Wire (φ2.5*300) is inserted. The
penetration depth of the guide wire is again read on the Lag Screw Depth Gauge (Fig.16).
Gamma Locking Nail System
22
Gamma Locking Nail System
操作手册Surgical Technique
17Fig.17
19-1Fig.19-1
19-2Fig.19-2
20-1Fig.20-1
20-2Fig.20-2
Drilling of the proximal Lag screw hole
,(φ7.5/φ4.9) , ( 17)。
。
Remove the proximal Threaded Guide Wire. Be certain that the Screw Guides are firmly seated on the bone. Drilling is done cautiously over through the Tissue Protection Sleeve with the Step drill (φ7.5./φ4.9) into the femoral neck until the predetermined length (Fig. 17) of the Lag screw is reached. Do not drill any deeper than previously measured.
/ (φ7.5) ( 18),注, ,
( 19-1)。如有必要, ,当C臂X, / ( 19-2)。
Remove the Step drill and Drill Guide. Using the Lag Screwdriver, the selected Lag screw is screwed in through the Screw Guide. The Lag screw should be inserted carefully(Fig.18). In the case of weak cancellous bone, the danger of overrotation exists, even with very low insertion torques. After inserting the Lag Screw to the appropriate depth, the correct position of the Lag Screw is checked in both planes with the image intensifier(Fig.19-1). If necessary,begin advancing the Lag screwdriver clockwise against the Screw Guide. The surgeon continues to advance the Compressor while monitoring femoral neck compression using the C-arm, until the desired fracture reduction is achieved (Fig.19-2).
( 20-1, 20-2),
The distal Lag screw is inserted in the same way after drilling with step drill as described previously (Fig.20-1, Fig.20-2)And the two Screw Guides are removed.
,插入 (φ8/φ4),(φ4)的 (φ4) ( 22)
, ,10mm( )并固定好,
,
The Obturator is withdrawn, and the Drill Guide (φ8/φ4) inserted. Advance the appropriate size Drill bit (φ4),with the Drill Stop (φ4) attached to it at its proximal end, through the Guide(Fig.22). The surgeon now drills steadily through the lateral cortex. The drill should be stopped when the second cortex is reached. The Drill Stop is moved down until it is about 10 mm above the top of the Drill Guide, and fixed into place. This represents the thickness of the second cortex. Drilling is now continued through the second cortex. The Drill Stop prevents damage to the tissues beyond the bone, and also provides a method of estimating the correct length of the locking screw.
23
操作手册Surgical Technique
Gamma Locking Nail System
DISTAL LOCKING
如有必要, ,将 (φ8 )插入(φ10/φ8), ( 21)。作小切口,
, ,
With the Proximal Targeting still in place, retighten the Locking Screw if necessary. Assemble the appropriate Obturator (φ8) into the Screw Guide (φ10/φ8), and place both the Guide through one of the distal targeting holes for Lag Screw in the Proximal Targeting Guide (Fig21). Make a small incision through the skin and fascia lata. Spread the soft tissue down to the bone. Advance the Guide until it contacts the lateral femoral cortex.
21Fig.21
22Fig.22
24
Gamma Locking Nail System
操作手册Surgical Technique
23Fig.23
( )DISTAL LOCKING (CONTINUED)
, ,
( 23) ,
The appropriate length locking screw, measured from the base of the screw head to its tip,
is determined by measuring the amount of drill bit protruding from the drill guide,
ignoring the tapered end (Fig.23). A locking screw of this length is reserved, but not yet
inserted.
,将 ( 24),
,
,并按
The Drill Bit is removed with the Drill Guide. The
Graduated Angled Trocar is now inserted into the
Screw Guide (Fig.24), so that it passes through the nail,
and engages the far cortex. This trocar has now
stabilized the position of the Guide Bar. Do not drill
the second hole before inserting the angled trocar.
The second locking hole is now drilled, using an
identical technique. The length of the second locking
screw is determined as described above. 24Fig.24
25
操作手册Surgical Technique
Gamma Locking Nail System
25Fig.25
( )DISTAL LOCKING (CONTINUED)
,需要使用
If the bone quality is good, it may be necessary to tap the proximal cortex using the Tap.
,用 ( 25),推入, ,部8〜20mm ,
T型手柄, ,
Remove the Drill Bit and Drill Guide from the second Screw Guide. A locking screw of correct length is now inserted into screw guide (Fig.25), and pushed through the bone with the Hex Screwdriver first, until its thread engages the lateral cortex. Note that there is a circular mark on the T-wrench. This mark will be 8〜20 mm above the top of the screw guide when the locking screw has been pushed in sufficiently. There is no point in turning the T-wrench until this position has been reached, because there will be no thread in contact with the bone. The T-wrench is now turned steadily clockwise, exerting gentle pressure, until the mark on the shaft of the T-wrench reaches the top of the screw guide. One more full turn should be made to tighten the screw fully. It is important not to continue turning after this position has been reached, or the thread in the bone will be stripped.
, ,
The trocar is removed from the first Screw Guide, and the same technique followed for insertion of the second locking screw. Both Screw Guides are now removed. Before proceeding with distal locking, a final check must be made to ensure that any rotational deformity has been corrected, and that there is no distraction of the bone ends at the fracture site.
26
Gamma Locking Nail System
操作手册Surgical Technique
ALTERNATIVE METHOD OF ESTIMATING LOCKINGSCREW LENGTH USING THE DEPTH GAUGE
, ,
, , ,
If there is any doubt about the correct length of locking screw, either in respect of the
measurement recorded following drilling, or because the surgeon omitted this step, the
Depth Gauge may be used as follows: the surgeon should first check that the screw guide
is positioned correctly. The depth gauge cover is then unscrewed and removed.
, , ORTHMED®的
,
Remove the Drill bit and Drill Guide, and insert the Depth Gauge through the Guide until
the gauge captures the far cortex of bone. Read the measurement for the screw from at
the top of the Screw Guide. This depth gauge is only suitable for use with ORTHMED®
Tibial and Femoral nails, since its accuracy depends on a fixed length of screw guide.
注意: 2.5mm
Note:Choose a screw length that is at least 2.5mm longer than the depth measured, to
ensure that bicortical screw fixation is attained.
27
操作手册Surgical Technique
Gamma Locking Nail System
前言INTRODUCTION
ORTHMED® ,:1) ;2)
折部位;3) ;4) ,
The ORTHMED® Long Gamma Locking Nail system has extended the indications of intramedullary nailing to include comminuted fractures, fractures with bone loss, and proximal and distal fractures of the femur. The interlocking technique offers the advantages of: 1) a closed intramedullary nailing technique; 2) small incisions away from the fracture site; 3) reduced risk of infection; and 4) decreased risk of shortening or rotation. Exposure to radiation during proximal and distal targeting screw placement has been reduced with the instrumentation and methods described in these surgical techniques.
ORTHMED® ,直径从9mm到11mm, 340mm到420mm 20mm
The ORTHMED® Long Gamma Locking Nails is available in the most commonly used sizes. These nails range in diameters from 9.0mm to 11.0mm and lengths from 340mm to 420mm in 20mm increment.
ORTHMED® :The ORTHMED Long Gamma Locking Nail is indicated for use in a variety of femoral fractures (Fig. 1), such as: A. A. Comminuted fractures B. 多段骨折 B. Segmental fractures C. 骨折伴骨缺失 C. Fractures with bone loss D. D. Proximal and distal fractures E. E. Nonunions F. 粗隆下骨折 F. Subtrochanteric fractures G. G. Intertrochanteric fractures
28
Gamma Locking Nail System
操作手册Surgical Technique
:Contraindications include: Femoral fractures involving the knee joint A medullary canal obliterated by a previous fracture or tumor (如畸形) Femoral shaft having grossly abnormal, excessive bow (i.e., curvature deformity)
Overt systemic infection is an absolute contraindication.
, /
The implant is contraindicated for use in medial neck fractures. This implant may not provide the required/desired stability when used to treat some medial neck fractures.
注意: ,Note:The surgeon should be aware that the use of the system in osteoporotic bone, or improper placement of the nail could increase the risk of failure or cut out of the implant.
29
操作手册Surgical Technique
Gamma Locking Nail System
SURGICAL TECHNIQUE FOR ORTHMED® LONG GAMMA LOCKING NAIL
PRE-OPERATIVE TECHNIQUE
X
Proper preoperative planning is essential to successful interlocking or recon nailing of the femur. To determine the appropriate nail size, and an x-ray film of the unaffected extremity are necessary for determining canal size at the isthmus and for measuring the length of the femur to aid in determining nail length. The proper length of nail should extend from the tip of the greater trochanter to the epiphyseal scar. The diameter of the femoral nail should match the isthmus in the lateral x-ray projection.
注意:从36 X 10%〜15 X
NOTE:X-rays taken at a 36-inch distance from the x-ray source result in 10-15 percent magnification of bone. The surgeon should review the x-ray to assure that there are no unusual anatomic variations.
30
Gamma Locking Nail System
操作手册Surgical Technique
REDUCTION
It is important to reduce the fracture before beginning the surgical procedure.
INCISION AND EXPOSURE
从大粗隆上方1cm 5cm, ,, ,
Begin the skin incision 1cm proximal to the greater trochanter and carry it proximally about 5cm in line with the gluteus maximus muscle. A larger incision may be desired for obese patients. Split the fascia of the gluteus maximus in line with its fibers. Identify the subfascial plane of the gluteus medius, and palpate the posterior tip of the greater trochanter. Retract the muscles to facilitate visualization of the piriformis fossa.
, ,点。
This may be difficult in the obese patient, especially if flexion causes the tip of the trochanter to lie against the ilium. Positioning techniques used to expose the tip of the trochanter include adduction of the leg and positioning of the patient’s torso away from the affected extremity.
31
操作手册Surgical Technique
Gamma Locking Nail System
INSERTION SITE
( 26) ,( 27) ,并且靠近大粗隆;
, , (φ2.5*300)。
Locating the correct entry portal in the piriformis fossa is extremely important(Fig. 26). For the interlocking procedure, place the Pointed Awl at the piriformis fossa (Fig. 27) and check its position with A/P and lateral views before creating the portal. On the A/P image, the awl should lie at the base of the femoral neck adjacent to the greater trochanter. On the lateral view, it should be oriented just posterior to the center of the femoral neck. When the correct position is achieved, rotate the awl to create the entry portal for the Threaded Guide Wire (φ2.5*300).
, ,底
部,靠近大粗隆,好入口位置后, ,近端股骨使用8mm口。
An alternative method is to insert the Threaded Guide Wire(φ2.5*300)into the piriformis fossa while checking the position with A/P and lateral image intensification. The Guide Wire must lie at the base of the femoral neck just medial to the greater trochanter on the A/P view, and oriented just posterior to the center of the femoral neck on the lateral view. Remove the Guide Wire and use the optional 8mm Rigid Reamer to create the entry
portal.
GUIDE WIRE PLACEMENT
15See the chapter of "UIDE WIRE PLACEMENT" on page 15.
REAMING PROCEDURE
16See the chapter of "EAMING" on page 16.
26Fig.26
27Fig.27
32
29Fig.29
NAIL INSERTION
, ( 28),并用SW5
Select the appropriate size Nail. The nail must be rotated until it seats into the correct
position of the Nail Support Handle (Fig. 28) and the Locking Rod is then firmly tightened into
the nail, completing this with the SW 5 Wrench .
,
, ,
况下, ,
The nail is now manually inserted over the Guide Wire into the medullary
canal as far as possible, under image intensification. The nail is advanced
into the distal fragment until the step on the nail support is flush with the
surface of the bone. This indicates that the nail has been inserted to the
correct depth. Ideally, the nail should be inserted by hand, but gentle
tapping may be necessary.
注意:
Note: Remove the Guide wire prior to drilling holes and insert the Locking
Screws.
( 29),
The Sliding Hammer maybe attached to the end of the nail Locking Rod
(Fig. 29), and it must be tightened fully to avoid damage to the thread. The
nail can then be inserted into the correct position by gentle hammering.
Gamma Locking Nail System
操作手册Surgical Technique
28Fig.28
33
PROXIMAL LOCKING
19
See the chapter of "ROXIMAL LOCKING"on page 19.
DISTAL LOCKING
,
, ;
, 提供定位杆安装的位置,定位杆可以穿
, ,并用
There may be some bending of the nail, due to the pressure and weight of the soft tissues
and the bone. Medio-lateral bending of the nail will not affect the targeting significantly,
since this is the plane of screw insertion, but any bending antero-posteriorly will result in
failure of the locking. The stabilizing system is therefore designed to correct antero-
posterior alignment between the guide bar and the nail. The Distal Outrigger provides the
mounting point for a Stabilizing Rod which is inserted down to the nail through the
anterior femoral cortex, and the U-shaped Stabilizing Spacer correct the distance and
lock the Stabilizing Rod to the outrigger.
:
1. ,
2. , ,
The stages of distal locking therefore are as follows:
1. Stabilize the guide bar in the appropriate position to correct for any bending of the nail.
2. Make the incision(s) for distal locking, insert the screw guides down to the bone, and
complete the procedure.
操作手册Surgical Technique
Gamma Locking Nail System
34
Gamma Locking Nail System
操作手册Surgical Technique
( )DISTAL LOCKING (CONTINUED)
, SW5
;将 , , , ,
( 30)。
Remove the Proximal Guide Bar, tightened the Locking Rod using Sw5 Wrench. The
Connector Bar is attached to the Nail Support Handle and the Target device Locking Screw
tighten firmly by hand. The Guide Bar is mounted on the Connect Bar and the Bar Locking
Screw tighten firmly by hand. There have tow holes for Bar Locking Screw to fit in the
Connector Bar. Make sure to use the correct one that will promise the curvature of the
guide bar structure match the curvature of the femur or the nail (Fig.30).
, 。
The Distal Outrigger is now attached on the anterior side of the guide bar, at the middle of
the two distal locking holes. The Distal Outrigger Locking Screw is tightened firmly by
hand.
30Fig.30
35
操作手册Surgical Technique
Gamma Locking Nail System
32Fig.32
32Fig.32
( )DISTAL LOCKING (CONTINUED)
将 , , 15mm切
口至深筋膜, ( 31),推向骨面, ,
A Stabilizing Rod Guide is inserted through the hole in the outrigger down to the skin
anteriorly, and by palpation is centred over the middle of the femur. The point of contact
with the skin is noted. A 15 mm incision is made at this point, down to the deep fascia.
The Obturator is inserted into the Screw Guide (Fig.31), and the two pushed together down
to the bone. The muscle is then split longitudinally down to the bone. The Screw Guide is
centered over the middle of the femoral shaft, by palpation, using gentle pressure on the
guide bar in the frontal plane.
,插入 (φ8/φ6),并将 (φ6) , ,然后
( 32)。
The Obturator is withdrawn, and the Drill Guide (φ8/φ6) inserted. The Drill Bit (φ6) is
inserted down to the bone, using gentle pressure to keep the point in contact with the
cortex. The anterior cortex only is then drilled (Fig.32).
36
Gamma Locking Nail System
操作手册Surgical Technique
( )DISTAL LOCKING (CONTINUED)
,插入 (φ6), , ,
,
The drill bit is removed and the T-handled Reamer (φ6) inserted. The hole in the bone is
cleared by turning the hand reamer, until its tip can be heard and felt touching the nail.
Tapping the nail to confirm contact may be helpful. The hand reamer is then removed.
, ,
The Stabilizing Rod is inserted through the Screw Guide, and the hole in the anterior
femoral cortex, down to the nail, contact being confirmed by tapping its tip on to the nail.
: ,
端支架( 33)。
The U-shaped Stabilizing Spacer is now attached so that: the upper, narrowest fork fits into
the groove in the shaft of the stabilizing rod. The two other forks grip the screw guide and
the outrigger (Fig.33).
33Fig.33
37
操作手册Surgical Technique
Gamma Locking Nail System
( )DISTAL LOCKING (CONTINUED)
把持住定位杆的手柄,, , ,
,
The handle of the stabilizing rod is now held so that its tip is in contact with the nail. The surgeon maintains this contact throughout. If the handle is pushed too hard, it is sometimes possible to push the tip of the stabilizing rod past the nail. This must be avoided, since it will result in the drill bit passing posterior to the nail. Gentle contact is all that is required.
(φ10/φ8), 4〜5cm的皮, , ,
致。
Screw Guides (φ10/φ8) are now inserted through each of the holes in the guide bar. A single 4〜5 cm incision is made over the points of contact with the skin, down through the deep fascia. The incision is deepened by blunt dissection, splitting the ilio-tibial tract longitudinally, down to the bone, taking care to keep the incision in line with the fibres of the ilio-tibial band.
(φ8)
The more proximal Screw Guide is now inserted down to the bone, with the aid of the Obturator (φ8).
(φ8/φ4) , , (φ4) ,( 34)。
A Drill Guide (φ8/φ4) is inserted into this screw guide, and tapped gently to engage its teeth in the bone. The Drill Bit (φ4) is attached to the drill guide, and the Drill Stop locked
34Fig.34
38
Gamma Locking Nail System
操作手册Surgical Technique
( )DISTAL LOCKING (CONTINUED)
, ,
, (φ4) ,
定性。
The surgeon now grips the T-handle of the Stabilizing Rod, to keep its tip against the nail,
and MAINTAINS THIS POSITION THROUGHOUT THE DRILLING PROCEDURE. The first
locking hole is now drilled as for proximal locking, and the drill guide removed. A Pin(φ4)
can also be used to drill a recess on the cortex before using Drill Bit to increase its
stability.
, ,
The Graduated Angled Trocar is now inserted into the Screw Guide, so that it passes
through the nail, and engages the far cortex. This trocar has now stabilized the position of
the guide bar. Do not drill the second hole until the Graduated angled trocar is in position.
, ,
,
Now that Screw Guide alignment is maintained by this trocar, the surgeon may release the
handle of the stabilizing rod. The appropriate length locking screw, measured from the
base of the screw head to its tip, is determined as before, and a locking screw of this
length reserved, but not yet inserted.
, ,
,
The distal Screw Guide is now advanced down to the bone using the straight trocar and
locked in position. The Drill Stop is returned to the proximal end of the drill bit and the
second locking hole drilled, using an identical technique. The length of the second locking
screw is determined as described above.
39
操作手册Surgical Technique
Gamma Locking Nail System
35Fig.35
( )DISTAL LOCKING (CONTINUED)
, , ,再按
( 35)。
A locking screw of correct length is now inserted into the second Screw Guide, pushed
through the bone with the Hex Screwdriver until its thread engages the lateral cortex, and
screwed into place as described for distal locking of Standard Gamma Locking Nail
(Fig.35).
, ,
, X
失后,
The graduated trocar is removed from the first screw guide, and the surgeon again
maintains the position of the stabilizing rod by gripping its handle. The same technique is
followed for insertion of the remaining locking screw, after which both screw guides are
removed. A check is now carried out with the Image Intensifier or by X-ray to confirm that
both screws have passed through the nail and that reduction has been maintained. The
Stabilizing rod, and Distal Outrigger are removed.
40
Gamma Locking Nail System
操作手册Surgical Technique
LOCKING SCREW REPLACEMENT
, ,需要使用 , ,
If a locking screw should need replacing for any reason during the course of the operation,
the Locking Screw Extractor should be used, inserting it through the appropriate hole in
the guide bar, as described in the section on Nail Removal below.
FINAL CHECK
在拆除手柄之前, X ( 36),
, , , X
Before removing the handle from the nail, it is important to check all of the screws for
correct insertion (Fig. 36), both in the AP and lateral planes, either by image intensification
or X-ray films, ensuring that fracture reduction is satisfactory. All Lag Screws in the correct
position, both distal locking screws pass through the nail and penetrate the distal cortex.
These X-rays can also be used to confirm that the base of each screw head is firmly
positioned against the surface of the cortex.
36Fig.36
41
操作手册Surgical Technique
Gamma Locking Nail System
REMOVAL OF THE HANDLE AND CLOSURE
用SW5 , ,
,
,
The handle is removed after loosening the Locking Rod a few turns with the SW5 Wrench.
Once the Locking Rod and the Handle have been removed, a nail End Cap is placed over
the end of the nail. Note that the end cap has an unthreaded portion at its end. This
enables the surgeon to push the end into the nail to establish the correct alignment, and
thereby avoid damaging the thread. The nail end cap locked into place with the
Screwdriver.
骨屑,
It is recommended that the insertion area is washed liberally with saline to remove any
debris of reaming from the wound. This will reduce the likelihood of heterotopic bone
formation.
,
, , 24~48
In general, suction drainage should be used in the proximal wound only. The deep fascia
should be repaired in all incisions, and all wounds should be closed in layers in the usual
manner. Dressings should include a compression dressing and an elastic bandage wrapped
around the hip, in order to avoid wound seroma. The drain is removed after 24~48 hours.
42
Gamma Locking Nail System
操作手册Surgical Technique
POST-OPERATIVE MANAGEMENT
, , X
, 8周以后。
Early range of motion exercises of the knee and ankle are encouraged. Allow toe-touch
weight bearing to progress to full weight bearing as fracture callus increases on the X-ray
films, usually at six to eight weeks.
NAIL REMOVAL
, , ,
再将拔出手柄 ,
The proximal end of the nail is exposed through a small incision. It may be necessary to
clear some new bone from the end of the nail. The nail end cap is removed with the
Screwdriver. The Screw Adapter is screwed fully on to the nail. It is important to avoid
crossing the thread in the nail.
,清除新生骨, / ,
Make a small incision in the area of the existing proximal incision to expose the ends of
the Lag Screw. Clear any bony ingrowth away from the Lag Screw hex, and thread the Lag
Screwdriver into the Lag Screw. Threaded the Lag Screw Inserter into the Lag Screw and
tighten. Remove the lag screw, turning counter clockwise.
( ,
), : ,
,
, ,
,
上旋下, 的。
43
操作手册Surgical Technique
Gamma Locking Nail System
( )NAIL REMOVAL (CONTINUED)
The locking screws are now all removed. When locking screws require to be removed for
any reason, (e.g. nail extraction, or in the occasional case where the length of the chosen
locking screw is incorrect), this maybe accomplished using the Locking Screw Extractor as
follows: the Extractor is inserted down to the head of the screw, and is turned
counterclockwise. The thread on the outside of the locking screw head is a verse thread,
so it is necessary to turn the Extractor counterclockwise throughout this procedure. The
first turns lock the extractor to the screw head, and further turns will release the screw
thread from the bone. Once the thread has been disengaged from the cortex, the screw
should be pulled out directly. Further turns at this point will achieve nothing, as no thread
remains in the bone. Note that the locking screw is then disengaged from the extractor by
turning the latter clockwise, which is the opposite direction to normal. It may be necessary
to grip the smooth shaft of the screw with forceps during this procedure.
将打入(拔出) ( 37),
Attach the Screw Adapter into the nail (Fig.37). Screw the Sliding Hammer on to the Screw
Adapter and remove the nail.
,
In the normal course of events there is no restriction of physical activity once the wounds