PPPoA Test Configuration Example on IDL-4800 to ADE-4400 / 3rd party device.

PPPoA Test Configuration

Example on IDL-4800 to ADE-4400 / 3rd party device

2 / 22

PPPoA Test Configuration

ASUS AM_604g

PPPoA connection enabled

DHCP Server enabled

Uplink BP:

VLAN-2, tagged IF

Untagged IF

PVID-2

IP: Dynamic IP

PPP server

PC#1

VLAN-2 tagged IF

xDSL-1, PVC-1:

PVID-2, Untagged

ADE-4400

PPPoA connection enabled

DHCP Server enabled

3 / 22

PPPoA Test Configuration

PPPoE/PPPoA Server

IP DSLAM

Modem

Modem

L2 Switch

PPPoE / PPPoA serverUbuntu + PPPoE server

IP DSLAMIDL-4800

ModemADSL CPE

4 / 22

1. Make sure your PPP service on the Server is running.

2. Configures DSLAM to have a proper setting.

3. Configures the ADSL Modem (ex: ADE-4400 & ASUS AM_604g)

4. Configures your switch and make sure all VLAN setting is correct.

5. Verify traffic path of PPPoA connection.

Steps for the PPPoA test

5 / 22

DSLAM configuration

6 / 22

management mgmt 172.16.9.44 netmask 255.255.255.0management gbe 192.168.100.1 netmask 255.255.255.0route default 172.16.9.254snmp 1 community rw "public"igmp version v2igmp snoopinginterface gigabit 1 bridge default vlan 1 egress untag vlan 2 priority reserved tag isolationinterface gigabit 2 bridge default vlan 1 egress untaginterface xdsl 1 adsl-config line status service on bridge 1 pvc 0/35 pvc encapsulation auto default vlan 2 egress untaginterface xdsl 2 adsl-config line status service on bridge 1 pvc 0/35 pvc encapsulation auto default vlan 2 egress untagcluster-cfg name "u71577C"bye

< running config >

IDL-4800 DSLAM running config

7 / 22

Note: For the PPPoA application , please configure ADSL PVC encapsulation mode as “Auto”

IDL-4800 DSLAM running config

8 / 22

Example device:PLANET ADE-4400 configuration

9 / 22

1. Click Network WAN

2. Key in the parameters VPI: 0 VCI:35 according to DSLAM’s setting

3. Select VC-Mux (or LLC) for encapsulation

4. Select PPPoA

5. Enable NAPT

6. Key in User Name / Password

7. And then ADD to add the channel

8. Save the Configuration

Configuration on PLANET ADE-4400

10 / 22

Example device:ASUS AM_604g configuration

11 / 22

Configuration on ASUS AM_604g

1. Click Advanced Setup WAN

2. Click Add Button

12 / 22

Configuration on ASUS AM_604g (Cont.)

Input your VPI and VCI number

13 / 22

Configuration on ASUS AM_604g (Cont.)

Select connection type and encapsulation mode VCMUX or LLC for PPPoA

14 / 22

Configuration on ASUS AM_604g (Cont.)

1. Input your PPP Username and Password for PPPoA connection

2. Click Next Button

15 / 22

Configuration on ASUS AM_604g (Cont.)

16 / 22

Configuration on ASUS AM_604g (Cont.)

Click Save Button

17 / 22

Configuration on ASUS AM_604g (Cont.)

Click Finish button

18 / 22

Configuration on ASUS AM_604g (Cont.)

1. Click Advance Setup Routing Default Gateway

2. Select Enable Automatic Assigned Default Gateway check box

3. Click Save/Apply button

19 / 22

Configuration on ASUS AM_604g (Cont.)

1. Click Advance Setup LAN

2. Select Enable DHCP Server check box

3. Click Save/Reboot button

Save/ Reboot

20 / 22

PPPoA Status on ASUS AM_604g

If PPPoA works and all the settings of PPP server, DSLAM, and CPE are correct, the WAN Info of CPE will show status is ‘Up’ and PPP server will assign an IP to this CPE.

21 / 22

Verify traffic path of PPPoA connection

22 / 22

LAN/ WAN

ASUS AM_604g

PPPoA connection enabled

DHCP Server enabled

Uplink BP:

VLAN-2, tagged IF

Untagged IF

PVID-2

IP: Dynamic IP

PPP server

PC#1

VLAN-2 tagged IF

xDSL-1, PVC-1:

PVID-2, Untagged

PC#2

After PPP session is established, PC#1 can access the same LAN (PC#2) as PPP server and internet (WAN, depends on PPP server setting.) for testing.

PPPoA Verification

ADE-4400

PPPoA connection enabled

DHCP Server enabled

23 / 22