GT18 4-2004 SPECIFICATIONS Stanley Hydraaulic Tools 3810 S.E. Naef Road Milwaukie, Oregon 97267 Tel 503•659•5660 Fax 503•652•1780 Visit our website at www.stanley-hhydraulic-toolss.com Power Units Features and Benefits The new generation Stanley GT18 Power Unit is the latest in construc- tion site hydraulic power for tools. The GT18 conforms to the Hydraulic Tools Manufacturers Association (HTMA) Type 1 and Type 2 tool circuit recom- mended performance. It will deliver 5 gpm or 8 gpm at pressures up to 2000 psi with heat rejection capacity exceeding the HTMA recommendation of 5 hp. Significant feeatures of the GT18 are: • Computerized, electronic throttle control is standard on all models. The control allows for selection of constant engine speed or au- tomatic speed. Automatic speed increases engine speed from idle when it senses tool working demand. When there is no tool working demand, engine speed GT18 is returned to idle. The automatic speed mode provides lower fuel use and less noise. • All electric control system with rotary switches. • All components in the GT18 are assembled for easy routine ser- vicing. The upper frame can be removed for more serious servic- ing. • A quartz hourmeter in the control panel records engine run time. • The hydraulic pump is mounted directly to the engine eliminating any misalignment and ensuring long life of the drive coupling. • An in-tank hydraulic filter continu- ously cleans the hydraulic fluid and assures that refill fl uid passes through the filter for a clean refill. • A 35-Ah sealed, non-spillable, no-maintenance battery is located inside a covered compartment. • Moving the GT18 around is made easy with a lift-and-latch handle. • Both engine models (Briggs or Honda) have pressure lubrication systems with a pressure sensing switch that will shut down the en- gine if the engine oil level is too low. • Some GT18 models are available with 110 vac, 60 Hz electric power provided by a Briggs & Stratton PowerLink inverter system. This system will deliver 1000 watts, continuous and 1500 watts in- termittent power through GFCI receptacles. ITEM U.S.A. METRIC OUTPUT CAPACIY 5 or 8 gpm 20 or 30 lpm PRESSURE 2000 psi 140 bar CIRCUIT TYPE Open Center HYDRAULIC RESERVOIR CAPACITY 3 gallons 11 liters FUEL TANK CAPACITY 7 gallons 26.5 liters WEIGHT (WET) 330 lbs 150 kg LENGTH 35 in. 89 cm WIDTH 21/5 in. 54.6 cm HEIGHT 29 in. 73.7 cm ENGINES Briggs & Stratton 18 hp anguard Honda 20 hp OHV
6
Embed
Power Units GT18 - nyindustrialworks.comnyindustrialworks.com/PDFs/Popwer-unit-spec.pdf · 5 or 8 gpm 20 or 30 lpm 2000 psi circuits 140 bar circuit @ 2000 psi @ 140 bar (1) 10 gpm
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
GT18 4-2004
SPECIFICATIONS
Stanley Hydraulic Tools3810 S.E. Naef RoadMilwaukie, Oregon 97267Tel 503•659•5660Fax 503•652•1780
Visit our website at www.stanley-hydraulic-tools.com
Power Units
Features and BenefitsThe new generation Stanley GT18 Power Unit is the latest in construc-tion site hydraulic power for tools. The GT18 conforms to the Hydraulic Tools Manufacturers Association (HTMA) Type 1 and Type 2 tool circuit recom-mended performance. It will deliver 5 gpm or 8 gpm at pressures up to 2000 psi with heat rejection capacity exceeding the HTMA recommendation of 5 hp.
Significant features of the GT18 are:
• Computerized, electronic throttle control is standard on all models. The control allows for selection of constant engine speed or au-tomatic speed. Automatic speed increases engine speed from idle when it senses tool working demand. When there is no tool working demand, engine speed
GT18
is returned to idle. The automatic speed mode provides lower fuel use and less noise.
• All electric control system with rotary switches.
• All components in the GT18 are assembled for easy routine ser-vicing. The upper frame can be removed for more serious servic-ing.
• A quartz hourmeter in the control panel records engine run time.
• The hydraulic pump is mounted directly to the engine eliminating any misalignment and ensuring long life of the drive coupling.
• An in-tank hydraulic filter continu-ously cleans the hydraulic fluid and assures that refill fluid passes
through the filter for a clean refill.
• A 35-Ah sealed, non-spillable, no-maintenance battery is located inside a covered compartment.
• Moving the GT18 around is made easy with a lift-and-latch handle.
• Both engine models (Briggs or Honda) have pressure lubrication systems with a pressure sensing switch that will shut down the en-gine if the engine oil level is too low.
• Some GT18 models are available with 110 vac, 60 Hz electric power provided by a Briggs & Stratton PowerLink inverter system. This system will deliver 1000 watts, continuous and 1500 watts in-termittent power through GFCI receptacles.
ITEM U.S.A. METRIC
OUTPUT CAPACITY 5 or 8 gpm 20 or 30 lpm
PRESSURE 2000 psi 140 bar
CIRCUIT TYPE Open Center
HYDRAULIC RESERVOIR CAPACITY 3 gallons 11 liters
FUEL TANK CAPACITY 7 gallons 26.5 liters
WEIGHT (WET) 330 lbs 150 kg
LENGTH 35 in. 89 cm
WIDTH 21/5 in. 54.6 cm
HEIGHT 29 in. 73.7 cm
ENGINES Briggs & Stratton 18 hp Vanguard Honda 20 hp OHV
Stanley Hydraulic Tools3810 S.E. Naef RoadMilwaukie, Oregon 97267Tel 503•659•5660Fax 503•652•1780
All Stanley Hydraulic tools, parts, accessories and allied equipment are subject to design improvements, specification and price changes at any time without notice and with no obligation to units already sold. Weights, dimensions and operating specifications listed herein are subject to change without notice. Where specifications are critical to your applications, please consult Stanley Hydraulic Tools.
Stanley Hydraulic Tools and their as-sociated parts are warranted against defects in materials and workmanship for a period of twelve months from the date of purchase. Stanley Hydraulic Tools reserves the right to repair or replace only those parts which prove to have been defective at the time of purchase. This warranty becomes void if maximum flow and pressure ratings are exceeded.
Visit our website at www.stanley-hydraulic-tools.com
CIRCUIT TYPE Open CenterHyd.Tank Cap. 3 gallons 11 litersFUEL TANK CAPACITY 7 gallons 26.5 liters
WEIGHT (WET) 330 lbs 150 kg
WIDTH 21/5 in. 54.6 cmLENGTH 35 in. 89 cm
HEIGHT 29 in. 73.7 cmENGINES Briggs & Stratton 18 hp Vanguard / Honda 20 hp OHV
CONNECTOR HTMA Flush Faced Coupler
The new generation Stanley GTR Power Unit is the latest in construction site hydraulic power for tools. TheGTR conforms to the Hydraulic Tools Manufacturers Association (HTMA) Type 1 and Type 2 tool circuitrecommended performance. It will deliver 5 gpm or 8 gpm at pressures up to 2000 psi with heat rejectioncapacity exceeding the HTMA recommendation of 5 hp.
Significant features of the GTR are:
Computerized, electronic throttle control is standard on all models. The control allows for selection ofconstant engine speed or automatic speed. Automatic speed increases engine speed from idle when it senses tool working demand. When there is no tool working demand, engine speed is returned to idle. The automatic speed mode provides lower fuel use and less noise.All electric control system with rotary switches.All components in the GTR are assembled for easy routine servicing. The upper frame can be removed for more serious servicing.A quartz hourmeter in the control panel records engine run time.The hydraulic pump is mounted directly to the engine eliminating any misalignment and ensuring longlife of the drive coupling.An in-tank hydraulic filter continuously cleans the hydraulic fluid and assures that refill fluid passes through the filter for a clean refill.A 35-Ah sealed, non-spillable, no-maintenance battery is located inside a covered compartment. Moving the GTR around is made easy with a lift-and-latch handle.Both engine models (Briggs or Honda) have pressure lubrication systems with a pressure sensing switch that will shut down the engine if the engine oil level is too low.
Stanleyrailroadproducts
Stanley products are available to suit many of the world’s railwaystandards. For further details, please contact your distributor.
Stanley Railroad Products 3810 SE Naef Rd. Milwaukie, Oregon 97267 USA
DISTRIBUTOR DETAILS
Model Number Description
GTR10B02 Single Circuit Briggs& Stratton18hp w/ wheelsGTR20B02 Dual Circuit Briggs & Stratton 18hp w/ wheelsGTR20B06 Skid Mount Dual Circuit Briggs & Stratton 18 hp No WheelsGTR20H02 Dual Circuit Honda 20-hp w/ wheelsHPR20271D Dual Circuit Duetz/Ruggerini 16-hp Diesel w/ wheels
Note: All Power Units (except HPR20271D)listed above include auto throttle and electric hydraulic controls.
Accessories
Model Number Description31848 Dual Hose, 50 ft x 1/2 in., w/couplers31972 Dual Hose, 25 ft x 1/2 in., w/couplers58633 Twinned Hose, 25 ft x 1/2 in., w/couplers58634 Twinned Hose, 50 ft x 1/2 in., w/couplers13360 Hose Basket Kit52721 High Altitude (0-6000 ft) Carburetor Jet Kit for Honda52722 High Altitude (6000-8000 ft) Carburetor Jet Kit for Honda33212 Weather Cover
HP1/HPR Compact
Power Units
OPERATION AND PERFORMANCE
HP1 COMPACT HPR
ITEM U.S.A. METRIC U.S.A. METRIC
Output (2) 5 gpm @ (2) 20 lpm @5 or 8 gpm 20 or 30 lpm 2000 psi circuits 140 bar circuit@ 2000 psi @ 140 bar (1) 10 gpm @ (1) 38 lpm @
Running Gear 12 in. Wheels 31 cm Wheels 12 in. Wheels 31 cm WheelsRetractable Retractable Retractable RetractableHandles Handles Handles Handles
Stanley's compact power units featurethe most efficient hydraulic circuits avail-able in a portable power unit today.
Built to meet the tough HTMA standards.HTMA standards so they’ll provide sure
Equipped with a high-speed blower andlarge air-to-oil cooler, our power unitsprovide a source for clean and coolhydraulic power under the toughestoperating conditions.
All models feature either the powerfulBriggs & Stratton Vanguard OHVV-Twin, or Honda OHV GX620 engine.These high-torque engines are fuel effi-cient, have lower exhaust emissions, yetrun quieter than most engines their size.
These power units are easy to service too– both the engine and the hydraulic spin-on filters are a snap to change. A largereadily available commercial battery isfully enclosed in a battery box.
All Stanley Hydraulic Tools, parts, accessories and allied equipment are subject to design improvements, specification and price changes at any time without notice and with noobligation to units already sold. Weights, dimensions and operating specifications listed herein are subject to change without notice. Where specifications are critical to yourapplications, please consult Stanley Hydraulic Tools.
ORDERING INFORMATION
PART NO. DESCRIPTION
13360 Hose Basket Conversion Kit (HP1, HPR)
33212 Weather Cover (HP18294)
32320 High Altitude Jet Kit (Briggs & Stratton)
28705 Rail Wheel Kit (HPR)
29548 Rubber Tire Kit (HPR20260, HPR20290)
ACCESSORIES
Dual Circuit Power Unitshown with Track WheelKit and Rubber Tire Kit.
WARRANTY
Stanley Hydraulic Tools and their associatedparts are warranted against defects in materi-als and workmanship for a period of twelvemonths from the date of purchase. StanleyHydraulic Tools reserves the right to repair orreplace only those parts which prove to havebeen defective at the time of purchase. Thiswarranty becomes void if maximum flow andpressure ratings are exceeded.