Poor Mans Fiber Network By: Chuck Hogg Shelby Broadband Welcome to FISPALIVE Nashville 2014.

Poor Man’s Fiber Network

By:

Chuck HoggShelby Broadband

Welcome to FISPALIVENashville 2014

FISPALIVE 20142

Introduction

Chuck Hogg

• President, Shelby Broadband• WISPA President and Board Member• An ISP since April 2006• Largest WISP in Kentucky, covering from Southern

Indiana to east of Lexington with over 140 sites serving 3500+ customers

FISPALIVE 20143

How did we figure it out?

– Attended nearly every fiber session I could at tradeshows– Visited other ISP’s that we felt were leaders in our industry

• Jason Hunt, Hunt Brothers Telecom• Chuck McCown, Wireless Beehive/Beehive Broadband

– Reviewed multiple locations in our existing service area and began planning

– Became a CLEC (right of ways)– FOA Handbook– School of Hard Knocks, we did 3.1 miles over a couple months

on the first project; we just finished 2 miles in 2 weeks on our last project

FISPALIVE 20144

Supporting Equipment

– 2 Forklifts ($13k)– Air Compressor ($5k)– 2 Missiles ($2k)– Cabinets ($6k)– Fitel Fusion Splicer ($6k)– Corning Ribbon Fusion Splicer ($4k)– Condux Fiber Blower/Pusher ($7k)– Double Reel Trailer ($1,250)– Ditch With JT922 ($60k)– Ditch Witch 4010 ($4k)– Splicing Trailer ($13k)

FISPALIVE 20145

ShelbyBB FTTH Project

Our First Deployment– 18k feet– 72 lots with 54+ Homes

FISPALIVE 20146

ShelbyBB FTTH Project

– Vaults (17 at $170ea, $2,890)– 3M Splice Cases on eBay (30 at $25ea, $750)– 8k’ 6 Strand Drop Cable for service drops ($1,600)– 40k’ 1-1/4” SDR HDPE Conduit ($12,800)– 11k’ Armored 72 Strand Ribbon ($6,930)– 6k’ Armored 96 Strand Ribbon ($4,290)– 1.5k’ Armored 24 Strand Ribbon ($660)– 10k’ Toneable Flat Drop 4 Strand ($1,190)– And many other small accessories and items

FISPALIVE 20147

ShelbyBB FTTH Project

– Total cost including labor to install single 1-1/4” duct $6,000 per mile

– Total cost with installation of the fiber $5,800 per mile

– Ground Remediation Costs $1,200 per mile– Utility damage costs $500 per mile– Vault installation $1,000 per mile

FISPALIVE 20148

ShelbyBB FTTH Project

– Fiber splicing and preparation $1000 per mile– Project management and planning $1,000 per

mile– Miscellaneous costs $1,000 per mile– Total cost per mile estimated at $17,600 per mile– No costs were included for machines or

maintenance, but we did include diesel– In this project, we had approximately $5,000 in

repairs due to bad/old equipment, but newer equipment had $800 in repairs.

FISPALIVE 20149

ShelbyBB FTTH Project

– Served by High Capacity 24GHz AirFiber (750Mbit Full Duplex) 2 miles from our facility

– Actual cost of infrastructure $58k– Planet Technology Metro-E Switch $800– RouterBoard 2011 for CPE $100– Average cost of install $500– Installation revenue $300– Expected yearly net revenue of $22k– Break-even point approximately 3-4 years

FISPALIVE 201410

ShelbyBB FTTH Project

The 1st with Fiber WINS!