PLUMBING PRODUCTS - pentairaes.com · Online Orders: PentairAES.com I Phone Orders and Tech Advice: 877.347.4788 PLUMBING Butterfly Valves 349 KEYSTONE COMPOSEAL RESILIENT SEATED

Online Orders: PentairAES.com I Phone Orders and Tech Advice: 877.347.4788

348 SECTIONProducts / Products / Products


PRODUCTS349 Valves356 Mesh Tubes/Strainers357 Bulkhead Fittings359 Tank Fitting Kits/Drains360 Plugs/Couplings/Caps361 Hose/Clamps/Rubber Seal362 Flexible PVC/Pipe Hangers/Supports/Saddles363 Tubing364 Clear PVC/Tubing366 Brass Adaptors/Modular Piping367 Tubing Adapters/Fittings368 Reducers369 Tees/Crosses/Insert Adapters370 Ells/Nipples/Caps371 Unions/Plug/Sweep372 Bushings/Couplings/Adapters373 Quick Disconnect Fittings374 ANSI Flanges/Bolt Sets375 Plumbing Supplies376 Garden Hoses & Accessories

PLUMBING


PLUMBINGButterfly Valves

349

KEYSTONE COMPOSEAL RESILIENT SEATED BUTTERFLY VALVES WAFER STYLEResilient seated butterfly valves with valve body and disc in high engineered composite material providing excellent internal and external chemical resistance.Since the entire valve exists of high engineered composite materials, it is perfectly suited for a wide range of applications such as; building services, hot water applications, industrial waste water and industrial water treatment like purification, ozone or demineralization.The light weight valve can be perfectly used in transportation and cargo containers and in applications using metal, plastic or glass reinforced pipe lines.

Features• Wafer style body and disc in high engineered composite results in excellent

internal and external chemical resistance• Light weight construction results in lower cost and simplified installation• No extra pipe support needed when installed in plastic or GRP piping• Disc in high engineered composite material provides excellent

corrosion resistance• All fasteners in stainless steel 316 as standard• Bubble tight shut-off in both directions, in accordance with EN 12266-1

leakrate A• Pressure range up to PN 16 at elevated temperature• Valve can be used in high line velocity applications up to 40 ft/sec• Spindle and primary valve seals are not influenced by the flange bolting force

or pipe flange type• High Cv value• No need for flange gaskets• Primary stem sealing exceeds the pressure rating of the valve and prevents

leakage through the shaft area to atmosphere• A secondary (shaft) sealing provides back-up safety• Four integrated locating holes ease installation and centering between the

pipe flanges• Actuator flange acc. ISO 5211• Sustainable production philosophy as the valve materials are 100% recyclable• Use of composite material eliminates the need for machining and painting• Composite hand lever available• Available water approvals: KIWA, ACS, WRAS, NSF, BELGAQUA• Certified and approved according Det Norske Veritas (DNV)

Gear Operated - Hand WheelMODEL MM INCH EACH

CSW100442WM1GO 100 4 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN 100 / GEAR OP. $566.99CSW125442WM1GO 125 5 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN 125 / GEAR OP. 566.99CSW150442WM1GO 150 6 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN 150 / GEAR OP. 698.29CSW200442WM1GO 200 8 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN 200 / GEAR OP. 871.49CSW250442WM1GO 250 10 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN250 / GEAR OP. 1,344.00CSW300442WM1GO 300 12 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN300 / GEAR OP. 1,691.00

Lever HandleMODEL MM INCH EACH

CSW050442WM1LHE 50 2 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN 050 / FIG 419 LEVER $178.49CSW065442WM1LHE 65 2.5 WAFER TRIM 442 COMPOSITE/EPDM WA3 DN 065 / FIG 419 LEVER 220.49CSW080442WM1LHE 80 3 WAFER TRIM 442 COMPOSITE/EPDM WA3 DN 080 / FIG 419 LEVER 236.29CSW100442WM1LHE 100 4 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN 100 / FIG 419 LEVER 272.99CSW125442WM1LHE 125 5 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN 125 / FIG 419 LEVER 335.99CSW150442WM1LHE 150 6 WAFER, TRIM 442 COMPOSITE/EPDM WA3 DN150 / FIG 419 LEVER 388.49

Integrated ISO 5211 top plate.

Integrated flange sealing.

Spherical disc edge.

Smooth Composite body surface eliminating the need to apply paint.

Primary body split sealing.Secondary body split sealing.

Thin disc profile resulting in high Cv values.

Four body locating holes on all sizes.

Gear Operated Lever Operated


350 PLUMBINGButterfly Valves/Ball Valves

MODEL EACH

1605005 1/2” TYPE-21 BALL VALVE PVC/FKM SOCKET/THREADED COMBO $27.291605007 3/4” TYPE-21 BALL VALVE PVC/FKM SOCKET/THREADED COMBO 33.591605010 1” TYPE-21 BALL VALVE PVC/FKMSOCKET/THREADED COMBO 41.991605012 11/4” TYPE-21 BALL VALVE PVC/FKM SOCKET/THREADED COMBO 52.491605015 11/2” TYPE-21 BALL VALVE PVC/FKM SOCKET/THREADED COMBO 72.391605020 2” TYPE-21 BALL VALVE PVC/FKM SOCKET/THREADED COMBO 88.191613015 11/2” TYPE-21 BALL VALVE CPVC/FKM SOCK X THRD 94.491609020 2” TYPE-21 BALL VALVE CPVC/EPDM SOCK X THRD 135.491607030 3” TYPE-21 BALL VALVE PVC/FKM THREADED 198.491607040 4” TYPE-21 BALL VALVE PVC/FKM THREADED 355.991606030 3” TYPE-21 BALL VALVE PVC/FKM SOCKET 198.491606040 4” TYPE-21 BALL VALVE PVC/FKM SOCKET 355.99

TYPE-21 BALL VALVE• Pressure rated up to 230 psi (PVC, CPVC, PVDF)• Double O-ring seals on stem for added protection• Full bore, sizes 1/2"–2"• Full vacuum rated, all sizes• Blocks in two directions, upstream and

downstream, leaving full pressure on the opposite end of the valve

• Integrally molded ISO mounting pad for both manual and actuated operations

• Integrally molded base pad to mount valves securely or panel mounting

• PTFE seats with elastomeric backing cushions ensure bubble-tight shut-off and a low fixed torque, while at the same time compensating for wear

• True Union design for easier installation or repairs without expanding the pipe system

• Built-in spanner wrench on the handle for valve disassembly and assembly

• Two sets of end connectors (socket and threaded) included with all PVC and CPVC valves in sizes 1/2"–2"

• CPVC threaded end connectors on sizes 1/2"–1" come with stainless steel reinforcing rings

• New PTFE Seat design—Facilitates easier field maintenance if required

• Tapered O-ring groove—Helps to Keep the end connector O-rings on the valve body during installation

MODEL EACH

1070005 1/2” OMNI BALL VALVE PVC/EPDM SOCKET $17.291070007 3/4” OMNI BALL VALVE PVC/EPDM SOCKET 22.591070010 1” OMNI BALL VALVE PVC/EPDM SOCKET 26.791070012 11/4” OMNI BALL VALVE PVC/EPDM SOCKET 37.291070015 11/2” OMNI BALL VALVE PVC/EPDM SOCKET 46.691070020 2” OMNI BALL VALVE PVC/EPDM SOCKET 94.49

TYPE 57 BUTTERFLY VALVE• PVC Body and EPDM Seat PVC Disc • Our 316 stainless steel shaft has full engagement over the entire length of the disc and is a non-wetted

part, totally isolated from the media• Only solid and abrasion-resistant plastic disc and elastomeric liner are wetted parts• ISO bolt circle on top flange—no body or stem modifications required for accessories

MODEL EACH

3722030 3” PVC BODY & DISC EPDM SEALS LEVER-OP TYPE 57 BTRFLY $267.79

3722040 4” PVC BODY & DISC EPDM SEALS LEVER-OP BTRFLY 313.993722060 6” PVC BODY & DISC EPDM SEALS LEVER-OP BTRFLY 471.49

Asahi/America® is a registered trademark of Asahi/America, Inc.

BUTTERFLY VALVES Asahi /America® butterfly valves are known for their high quality, high strength and positive closure. They are made of PVC, polypropylene and stainless steel and feature a notched gauge plate which allows more accurate judging of the percentage of opening. Fit US standard flanges (see Index for flanges).

MODEL SIZE SHIP WT (LBS) EACH

BV115 11/2” 3 $164.99BV200 2” 3 172.49BV300 3” 4 204.79BV400 4” 5 269.89BV600 6” 13 348.89BV800 8” 23 603.89

OMNI BALL VALVE• Blocks in two directions• Rugged structure• Unibody construction• Compact, low profile, short

face-to-face dimensions• PTFE seat backed by EPDM for

low stem torque• Rated for full vacuum service


PLUMBINGBall Valves

351

TRUE UNION BALL VALVES TECH FAV

These high-quality valves are available at low-end prices. They feature PTFE seats that provide easier turning, better sealing and longer valve life. Schedule 80 PVC with EPDM O-rings rated at 150 psi at 72ºF. Slip unions are included for all valves. All except TB3 and TB4 have molded actuator attachments.

MODEL SHIP WT (LBS) EACH

TB12 1/2" 1 $10.19TB34 3/4" 1 12.59TB1 1" 2 16.99TB114 11/4" 2 22.89TB112 11/2" 3 29.89TB2 2" 4 40.49TB3 3" 11 113.69TB4 4" 30 232.89

ECONOMY BALL VALVESLow-cost yet heavy-duty Schedule 40 ball valves. They have EPDM seats and seals, rated at 150 psi, with full port flow openings.

Three-WayTwo-Way

TB2

SINGLE UNION BALL VALVES These high-quality ball valves allow disconnection of lines without fear of retainer-ring or ball moving. The retainer-ring is locked with two pins to the body. PVC with EPDM O-rings and polyethylene seats. Rated at 150 psi. Available in 11/2” and 2” only.

MODEL EACH

BV112S 11/2” SLIP X SLIP $16.59BV112T 11/2” FNPT X FNPT 20.69BV2S 2" SLIP X SLIP 22.39BV2T 2" FNPT X FNPT 27.69

SINGLE UNION BALL VALVES These ball valves are made entirely of glass-filled polypropylene for strength and chemical resistance. They feature low-operating torque (as in easy to open and close), PTFE seats and double EPDM O-rings in the stem area and a 150 psi rating. Choose two- or three-way style.Note: Union may not be removed while under pressure, even if in the “off” position.

MODEL FNPT EACH

PBV132 1/2" $17.39PBV133 3/4" 17.29PBV134 1" 21.19PBV135 11/4" 28.49PBV136 11/2" 38.19

Two-Way, Single Union Three-Way, Single UnionMODEL FNPT EACH

PBV232 1/2" $31.99PBV233 3/4" 31.29PBV234 1" 39.19PBV235 11/4" 45.09PBV236 11/2" 52.49PBV237 2" 62.79

SBW12

BALL VALVES TECH FAV

These high-quality ball valves are offered at an unbelievable price! They feature PTFE ball seats and EPDM O-rings. The valves are very easy to turn. Maximum 150 psi rating. Certified by NSF for potable water use.

SHIP WT SLIP THREADED SIZE (LBS) MODEL EACH MODEL EACH

1/2” 1 SBW12 $3.39 SBW12T $3.193/4” 1 SBW13 3.79 SBW13T 3.591” 1 SBW14 4.89 SBW14T 4.691¼” 1 SBW15 6.89 SBW15T 6.691½” 1 SBW16 10.89 SBW16T 10.492” 2 SBW17 13.59 SBW17T 16.293” 6 SBW18 52.49 SBW18T 50.994” 10 SBW19 85.59 SBW19T 85.59

SHIP WT SLIP THREADED SIZE (LBS) MODEL EACH MODEL EACH

1/2” 1 2622005 $6.59 2622005T $6.593/4” 1 2622007 7.59 2622007T 7.591” 1 2622010 10.29 2622010T 10.291¼” 1 2622012 15.09 2622012T 15.091½” 1 2622015 20.69 2622015T 20.692” 2 2622020 25.19 2622020T 25.19


352 PLUMBINGMotorized Ball Valves/Solenoid Valves

12V 2-WAY BALL VALVESPerfect for aquacultureThe KZValve QX Series 2-way, 12V 1.5A Ball Valves are powered by high-torque, valve-actuating motors. Permanently lubricated, machined steel gears open and/or close thepolypropylene ball valve in 1.5 seconds. These valves are heavy-duty, fully weatherproof and compatible with recirculating aquaculture water containing fish feces (not mud, sand or debris). Supplied with a 24” four-wire lead (you supply the switch). The 12V adapter (992) will operate one valve. The ball valves can be disassembled. One-year warranty.• NEMA 6P rated waterproof actuator housing• 316 stainless steel ball and stem

MODEL EACH

900 VALVE, 3/4" $297.89902 VALVE, 1" 302.49904 VALVE, 11/2", 12V 393 .79906 VALVE, 2" 484.09908 VALVE, 3" 734.99992 ADAPTER, 115VAC TO 12VDC 29.39

STAINLESS STEEL COMPACT SOLENOIDThis UL-listed solenoid valve has 1/4” NPT in/out ports, 0–140 psi range, fluoroelastomer rubber seal material and 1/2” NPT conduit connection. 115V/60 Hz only. 17 VA (hold), 24 VA (inrush). NEMA 4.

MODEL EACH

813NC NORMALLY CLOSED $148.99

LARGE OPENING SOLENOIDSFor a high volume of air or water, a large opening is needed. These solenoid valves are servo assisted to open and close openings up to 11/2”. Rated to 140 psi, they require no differential pressure. Brass body. Opening sizes same as in/out sizes. 115V/60 Hz, normally closed only. NEMA 4. Each weighs 2 lbs. Allow one week for shipment.

MODEL EACH

817NC 1/2” $209.59818NC 1” 347.29

SOLENOID TIMERThis NEMA 4 outdoor-rated timer can be fitted to any solenoid on this page (plug standard to DIN 43 650). Timer is programmable via DIP switches and potentiometers. Can be programmed for various on/off cycle times from 1 second to 100 hours, including switch-on impulse. LED display, maximum power consumption is 1.5 watts. It features NEMA 4 protection and working temperature from 14–140ºF. 115V/60 Hz.

MODEL EACH

825 $133.19

115V BALL VALVES Schedule 80 heavy-duty ball valves feature PTFE seats and seals and 115V 50/60 Hz actuator motors. Their 5-second opening and 5-second closing speeds prevent water hammer. The motor has a NEMA 4X protective cover. Locked rotor amp draw is 2.2 (running amps will be about 1.5). One-year warranty.

SOLENOID VALVESFor automating the flow of air, water, oil, etc., these valves are UL-listed with 1/2” NPT conduit connection (12V) or cord nut (115V). The valve body is brass with stainless steel internals. Temperature range is 14–194ºF (-10–90ºC). 1/8” NPT ports and internal opening, .3 gpm @ 1 psi, 2.2 gpm @ 85 psi. 85 psi max @ 12V, 145 psi max @ 115V, 8 watts. Rated for continuous duty.

MODEL EACH

81NC 115V, N.C. $87.39811NO 115V, N.O. 153.9982NC 12V, N.C. 91.49812NO 12V, N.O. 142.59

817NC

MV34

81NC

906

SLIP FNPT SIZE MODEL EACH MODEL EACH

3/4” MV34 $329.09 MV34T $329.091” MV1 336.19 MV1T 336.1911/4” MV114 345.99 MV114T 345.9911/2” MV112 354.49 MV112T 354.492” MV20 367.09 MV20T 367.09


PLUMBINGGate Valves/Air Purge Valves

353

AIR PURGE VALVE, HIGH FLOWPrevents gas bubble diseaseInstall at high points in an aquaculture pressurized water system where air accumulates. Water pressure automatically forces air out, and when water reaches the valve, the internal float creates a watertight seal. Must be mounted vertically. Seals from 2 to 100 psi. Under suction, the valve functions as a vacuum breaker. 1” FNPT threads, measures 51/4” H x 2” in diameter. Air discharge rates (cfm): 60 @ 12.5 psi, 100 @ 25 psi and 180 @ 50 psi.

353

1

2 3

Inlet

3-PORT VALVEAllows proportional flowOne 3-way valve can take the place of three regular valves in some situations. This unit can be disassembled for cleaning and fits 11/2” and 2” PVC pipe (11/2” slips into valve sockets, 2” pipe requires couplings or bell ends). The inlet is always open. The handle position closes sides 1 or 3. When in position 2, none is closed.

AIR PURGE VALVEThis brass valve has an internal float that closes the valve when filled with water. Use it to automatically purge air from a water tank, pipe system, oxygen saturator, etc. Mount it vertically wherever air collects. Also works as a vacuum breaker. 1/4” MPT. 1/4”poly plug included.

MODEL EACH

ST5 $22.29

MODEL EACH 4+

SV300 $45.29 $43.03

MODEL OVERALL LENGTH EACH 4+

ST4 3” $16.89 $16.05

PVC GATE VALVESPVC gate valves operate like their bronze counterparts but at a fraction of the cost. Gate valves are best suited to full open or full closed operation. Do not freeze. NSF-approved, 150 PSI maximum working pressure.

WGV12

SLIP FNPT SIZE MODEL EACH MODEL EACH

1/2” WGV12 $13.59 WGV12T $13.59

3/4” WGV34 16.79 WGV34T 16.791” WGV1 20.99 WGV1T 20.9911/4” WGV114 27.29 WGV114T 27.2911/2” WGV112 34.59 WGV112T 34.592” WGV2 40.89 WGV2T 40.89

ECONOMICAL PVC GATE VALVESPVC, pressure-rated to 40 psi. Do not freeze. Valves include “gate keeper” accessory to hold gate open.

MODEL EACH

GV112-2 11/2" SLIP $7.99GV2-2 2" SLIP 12.39

GV112-2

GATE VALVE REPLACEMENT PARTSThese replacement seals fit our GV part numbers up to 8”. Made of TPE and sold either in kits, which include two seals and the required nuts and bolts, or as seals only for 4”, 6” and 8” valves.

MODEL EACH

RSK112 11/2" SEAL KIT $5.19RSK2 2" SEAL KIT 5.89RSK3 3" SEAL KIT 7.59RS4 4" SEAL (1) 3.19RS68 6" AND 8" SEAL (1) 37.89PH112 PLASTIC HANDLE, 11/2–3" 3.79MH112 METAL HANDLE, 11/2–4" 5.19

GV2

PVC KNIFE GATE VALVESPerfect for waste drains and low-pressure aquacultureKnife gate valves are economical, quick-acting valves for clean and dirty water low-pressure applications. They have become very popular in the aquaculture industry for several reasons: they can be easily taken apart, the seals can be changed and even the valve body can be changed without upsetting the ends that may be glued to your pipes. Therefore, they can be used in place of unions. If you have a valve glued in place, but want to take it out, you can simply unbolt it and purchase new side pieces. They offer unrestricted flow and are quick opening, 100% water tested at the factory and quite low in cost. These 11/2” to 8” valves are all PVC with stainless steel shafts, polypropylene knife gates (except for 4”, 6” and 8”, which are stainless steel), and have TPE seals. The valves are all slip x slip, they are not for use in freezing weather. One-year warranty.

MODEL MAX PSI SHIP WT (LBS) EACH 6+

GV11 11/2" 45 1 $13.69 $12.32GV2 2" 40 1 19.49 17.54GV3 3" 30 2 27.69 24.92GV4 4" 20 5 81.09 72.98GV6 6" 10 18 354.69 319.22GV8 8" 10 20 528.69 475.82

GV3

GV4

RSK112


354 PLUMBINGCheck Valves/Well Screens

PVC SWING CHECK VALVES For use in fresh or salt water with a minimum of head loss. They’re completely nonmetallic and use no springs. They’re pressure rated up to 100 PSI and mount both horizontally and vertically. They have a full-flow design with a Buna-N seal and hinge (slip x slip). Not recommended for use with air.

CHECK VALVES Quick and positive action in any position. Polypropylene valve is highly resistant to chemicals and temperatures up to 100ºC (212ºF). Use for any pressure or vacuum system. 228225 will fit tubing 8–10 mm (1/4”–3/8” I.D.). Overall length 21/2”. 228215 fits tubing 11–15 mm (7/16”–5/8” I.D.). Overall length 23/4”.

MODEL EACH

228225 FITS 8- TO 10-MM TUBING $4.09228215 FITS 11- TO 15-MM TUBING 5.29

CCV12

228225

CV1

1720C20

PVC TRUE UNION SWING CHECK VALVESFor use in fresh or salt water with a minimum of head loss. They’re completely nonmetallic and use no springs. They’re pressure rated up to 100 PSI and mount both horizontally and vertically. They have a full-flow design with a Buna-N seal and hinge (slip x slip unions). They feature quick change bodies. Not recommended for use with air.

CV9

MODEL VALVE SIZE EACH

1720C07 3/4” $21.391720C10 1" 24.391720C15 11/2” 28.891720C20 2" 41.391720C30 3" 76.59

PLASTIC CHECK VALVESFor use in fresh water, salt water or air. Excellent for foot valves on pumps. These plastic check valves are offered without springs or with 1/2-lb stainless steel springs for more positive closure. WITHOUT SPRINGS WITH SPRINGS FNPT MODEL EACH MODEL EACH

3/4” CV1 $10.59 CV185 $11.491” CV2 10.89 CV285 11.4911/4” CV3 16.09 CV385 16.9911/2” CV4 19.19 CV485 20.192” CV5 23.49 CV585 22.29

VALVE PVC-WHITE PVC-CLEAR SIZE MODEL EACH 4+ MODEL EACH 4+

3/4” CV9 $15.29 $13.76 — — —1” CV10 16.59 14.93 — — —11/4” CV11 16.99 15.29 — — —11/2” CV12 17.49 15.74 CCV12 22.09 19.882” CV13 27.19 24.47 CCV13 34.69 31.223” CV14 51.29 46.16 CCV14 53.99 48.594” CV15 67.29 60.56 CCV15 77.29 69.56

WELL SCREENS & POINTSWell screens are for dewatering wet areas and use as pump pre-filters in lakes, ponds and culture systems to prevent debris or animals from being pumped with the water. Made from Schedule 40 PVC pipe, screens have precision-cut slots that are .01” or .04” and made horizontally to prevent collapsing and for more open area per foot than vertical slotting. Use the .01” screens with the “WP” well points to create a shallow well; use the .04” size for less clogging or higher flowrates. Flowrates are per linear foot and are based on 0.1 ft/sec entrance velocity. Order well points separately; see our “PVC Fittings” section for threaded adapters, tees and caps to complete your installation. All screens are 5’ OAL and ship Oversize.

Well Points Only (Fit Schedule 40 Pipe Also)MODEL PIPE SIZE SHIP WT (LBS) EACH 6+

WP125 11/4" 1 $1.89 $1.80WP150 11/2" 1 2.39 2.27WP200 2" 1 3.39 3.22

.01” ScreensMODEL PIPE SIZE GPM/FT SHIP WT (LBS) EACH 6+

WS1251 11/4" .7 4 $15.89 $15.10WS1501 11/2" .8 4 17.39 16.52WS2001 2" 1.3 5 20.29 19.28

.04” ScreensMODEL PIPE SIZE GPM/FT SHIP WT (LBS) EACH 6+

WS1504 11/2" 3 4 $21.39 $20.32WS2004 2" 4 5 22.19 21.08WS3004 3" 4.6 8 38.99 37.04WS4004 4" 6.9 11 48.99 46.54

WP125

WS1251

.01” IS ABOUT 250 MICRONS (THE THICKNESS OF A BUSINESS CARD)..04” IS ABOUT 1,000 MICRONS (HOUSEHOLD WINDOW SCREEN).

WP150

WS1504


PLUMBINGFloat Valves

355

INDUSTRIAL-SIZE FLOAT VALVESThese large-orifice PVC and polypropylene valves with EPDM O-rings are salt water compatible. Maximum operating pressure is 80 psi.

MODEL A B C EACH

541205-AQ 1/2" FNPT 3" 4.2" 12" $209.99541207 3/4" FNPT 3.5" 5" 12" 293.99541210-AQ 1" FNPT 3.5" 5" 13.5" 362.29

FLOAT VALVEMade of plastic for use with clean water only (do not use recirculated water). Mount it to a water supply/refill line at the desired water level. When that level is reached, the valve shuts off. It will maintain the level precisely at ±1/4”! Flow is 4 gpm @ 30 psi. Operating range is 10 to 120 psi. 1” FNPT inlet.

MODEL EACH

PL9 $36.99

C

A

B 541205-AQ

5"

3.75"

R825

RM262P31/2"

RM21431/2"

R610

8"

FLOAT VALVE, MECHANICAL

MODEL BODY OAL INLET PIPE SIZE OUTLETFLOW @ 35 PSI EACH

RM65 B&P 10" 1/4" HOSE BARB FREE FLOW 1.3 GPM $6.79

RM262P S 10" 1/4" MNPT FREE FLOW 1.3 GPM 63.79

R825 P 8" MGHT FREE FLOW 2.0 GPM 33.89

RM214 B 10" 1/2" MNPT 3/8" COMP. 3.0 GPM 18.49

R7002F B 20" 1/2" MNPT 1/2" MNPT 12 GPM 66.69

R610 B 28" 11/2" FNPT FREE FLOW 112 GPM 141.19

B=Brass, P=Plastic, S=Stainless.Note: 100 psi maximum pressure. OAL is overall length with float.

ABS FLOAT VALVEGreat for R/O tanksThis mechanical float valve is made entirely of ABS plastic, compatible with saltwater applications. It measures 81/4” long, has a 1/4” MPT inlet and a free flow outlet. Flow @ 30 psi is 1 gpm; maximum 90 psi.

MODEL EACH

RM51 $20.79




SECTIONProducts / Products / Products

08356 PLUMBINGMesh Tubes/Strainers/Foot Valves

270554

CV1S

TSS20

FTV1

MESH TUBES, PLASTIC Made from high-density polyethylene, these perforated screen tubes are great for fitting over standpipes, 3/16” (4 mm) openings. Sold in 44” lengths; fit nicely over Schedule 40 PVC.

MODEL FITS OVER EACH

RT144 1" PVC $10.29RT244X 2" PVC 20.09RT344X 3" PVC 23.29RT444X 4" PVC 26.99

STRAINERSPlastic strainers with slots that are approximately 1/8” wide in all sizes.

FOOT VALVESThese foot valves are perfect for koi ponds and small aquaculture applications. Consisting of a check valve and a strainer, they keep water in the line of non-self-priming pumps. The polymer check valves have no springs, can be used in fresh or salt water and have a very low pressure loss. Strainers are constructed of acetal resin plastic and have 1/8” slots.

MODEL NPT EACH

FTV34 3/4” $12.59FTV1 1" 12.59FTV114 11/4" 17.59FTV112 11/2" 20.19

RT144

STRAINERSMade from high-density polyethylene.

MODEL FNPT OPENINGS EACH

TSS20 11/2" 1/4" x 1" $7.99TSS25 2" 1/4" x 1" 7.99TSS35 3” 1/2" x 11/2" 18.39

STRAINERSStrainers fit check valves CV1 to CV4 and can be used for many applications. Made of acetal resin. Overall length includes threads. Strainer slots are approximately 1/8” wide on all sizes.

MODEL MNPT OVERALL LENGTH EACH

CV1S 3/4" 23/4" $1.39CV2S 1" 3" 1.69CV3S 11/4" 31/4" 1.79CV4S 11/2" 4" 2.19

MODEL MNPT OVERALL LENGTH EACH

270554 1/2" 21/4" $2.09270556 3/4" 27/16" 2.39175251 1" 213/16" 3.19270557 11/2" 35/8" 5.19270561 2" 37/8" 9.79

How to Glue PVC Pipe1. Square pipe ends and remove all burrs, dirt and debris.2. Check the dry fit of the pipe and fitting. The pipe should easily fit in one-third of the way. Pipe

should not bottom when dry; it should be a snug fit.3. Clean pipe and fitting with PVC cleaner, then prime with Purple Primer. Choose proper PVC

cement based on desired cure time (regular cement requires 24-hour cure vs "Rain Tight" 1-hour cure for low-pressure applications).

4. Apply a thin coat of PVC cement to fitting, avoiding puddling inside of pipe. Make certain the entire socket surface is covered.

5. Apply a liberal coat of PVC cement to pipe. Make certain the entire pipe surface to the socket depth is covered.

6. Quickly assemble parts. Cement must be fluid when attaching segments. If not, reapply cement to both parts.

7. Push pipe FULLY into fitting using a 1/4 turn motion until pipe bottoms.8. Hold pipe and fitting together for 30 seconds, then wipe off excess glue with a cloth.

Watch that it doesn't creep back.9. Keep cement container tightly closed when not in use.10. Do not pressure test until cement is fully cured, usually 24 hours.

TECH TALK 15


PLUMBINGValves

357

PLASTIC NEEDLE VALVEThese needle valves are small gate valves designed for applications where accurate flow is required. Valves have a barb inlet/ outlet.

MODEL FOR TUBING EACH

NV14 1/4" I.D. $12.79NV38 3/8" I.D. 13.09NV12 1/2" I.D. 13.09

RC9

VP31

BRASS BALL VALVES These top-quality ball valves feature corrosion-resistant, chrome-plate balls and PTFE seals for years of high-temperature easy, operation. The body is LA 377 brass forging. Plated steel handle with vinyl grip.


VBB2 1/2" FNPT $12.59VBB3 3/4" FNPT 18.79VBB4 1" FNPT 30.19

VK2

VBB2

SPIGOT VALVE Barb accepts 5/8” I.D. flexible tubing. Polyethylene.

MODEL EACH

TV1 1/2" MPT $13.19TV2 3/4" MPT 15.39

TV1

MV6

DC9

NV14

PV5USE FOR WATER TO 100 PSI.

VALVE MANIFOLDS, LARGE The PVC globe valves are glued together as manifolds to save you time. Each valve will pass 2 gpm with less than 1 psi pressure loss. These PVC valves have 1/2” FNPT outlets. The manifold ports are 1/2” FNPT and a threaded plug is included, which may be removed for another connection.

MODEL OAL EACH

PV2 2-VALVE 8" $27.49

PV3 3-VALVE 11" 42.49PV4 4-VALVE 14" 48.29PV5 5-VALVE 17" 58.89PV6 6-VALVE 20" 66.09

VALVE MANIFOLDS, MEDIUM Our valve manifolds will save you time and aggravation. They are made with quarter-turn valves (BV25). The manifold ports are 1/2” FNPT and a 1/2” FNPT plug is included. Each valve is 1/4”FNPT.Each valve will pass 1/2 gpm with less than 1 psi pressure loss. They also make excellent manifolds for air distribution. The 1/2” threaded plug may be removed for another connection.

MODEL OAL EACH

MV2 2-VALVE 8" $25.99

MV3 3-VALVE 11" 30.19

MV4 4-VALVE 14" 37.49MV5 5-VALVE 16" 47.59MV6 6-VALVE 18" 54.99

MSK558

MSK714

MSK610MSK816

MINIATURE STOPCOCKSFor low-pressure air and water.

MODEL FOR TUBING EACH 10+

MSK558 5/16" $2.09 $1.88MSK610 3/8" 2.19 1.97MSK714 1/2" 2.59 2.33MSK816 5/8" 2.59 2.33

HOSE VALVEEasily turned handle. Rated up to 45 psi at 100ºF (38ºC).


70012 1/2” I.D. $7.09

TUBING VALVESRC9 and RC10 are made of polyester (PBT) that offers permanent rigidity and stiffness even in high-humidity areas. Infinite variable flow. Easy one-hand operation. No metal parts. Chemical and temperature resistant. No corrosion. Ideal for continuous, long-term use for air or water. Autoclavable to 320ºF (160ºC).


RC9 1/8" TO 7/16" I.D. $7.99

RC10 1/4" TO 9/16" I.D. 8.89

TUBING VALVESClamp TypeManufactured of tough plastic without sharp edges. DC9 is an “on/off” valve only. The DC10 and DC11 have a 12-position ratchet control. Accurate and economical.


DC9 UP TO 1/4” I.D. $.25DC10 1/8” TO 3/8” I.D. 0.95DC11 UP TO 3/4” I.D. 2.79

DRUM FAUCETHere is a very low-cost polyethylene valve that can be used in low-pressure applications. Two-piece construction, 3/4” MNPT threads.

MODEL EACH 25+

DV34 $3.59 $3.23

GATE AND GLOBE VALVESPreferred where fine adjustments to flow are needed. Acetal resin (plastic) valves may be used for air or water at -20 to 180ºF and up to 100 psi. The no-kink style has a MNPT on its base and garden hose threads on the outlet. The VP31 is white PVC (not rated for compressed air) with slip sockets and glues onto 3/4” PVC pipe. All others are threaded. Washerless.


VC2 PLASTIC 1/2" FNPT GATE VALVE, STRAIGHT $6.29

VC3 PLASTIC 3/4" FNPT GATE VALVE, STRAIGHT 6.29

VP31 PVC 3/4" SLIP VALVE, STRAIGHT 6.09VK2 PLASTIC 1/2" MNPT VALVE, NO-KINK 5.29VK3 PLASTIC 3/4" MNPT VALVE, NO-KINK 5.49

VC2

Note: OAL = overall length

Note: OAL = overall length

DRIP EMITTERCan be used in almost any flow application. They have an infinite adjustment up to 2 gph and will screw into a 10-32 thread, 3/16" tubing or into the open end of a riser tube.

MODEL EACH 25+

42115-AQ $1.69 $1.52




Bulkhead Buying KeyFollow this key carefully to get the right bulkhead. Note that “F” is on the flange side and “L” is length between the gasket and the nut when the nut is at the maximum distance. The “size” of a bulkhead refers to the plumbing connections, the “F” or “B” dimension. The size of the hole needed is the “D” dimension. Do not use these threads for plumbing connections. All of our bulkheads come with one gasket. For most applications only one gasket is needed, located on the flange side, whether or not the flange side is on the water side

358 PLUMBINGBulkhead Fittings

TF1

35012L

BKF4

PREMIUM PVC BULKHEAD FITTINGSOur highest quality, BFA Series, PVC tank adapters have left-hand threads and a hex-shaped body that allows one-person installation. Heavy-duty, full-buttress threads help prevent leaks under pressure. Select either slip or female inside pipe thread. One EPDM gasket included.

TECH FAV

BULKHEAD FITTINGS These are a lower strength alternative to our top-quality PVC bulkheads and quite adequate for most applications. One EPDM gasket included.

MODEL GASKET # SIZE F B D L EACH

BKF1 Q10G 1/2" FIPT FIPT 11/8" 3/4" $5.99BKF2 Q10G 1/2" FIPT SLIP 11/8" 3/4" 6.99BKF3 GK1 3/4" FIPT FIPT 17/16" 1" 6.69BKF4 GK2 1" FIPT SLIP 13/4" 11/2" 8.59BKF5 GK2 1" FIPT FIPT 13/4" 11/2" 8.29BKF6 GK4 11/2" FIPT SLIP 23/8" 13/4" 9.99BKF7* GK5 2" FIPT SLIP 27/8" 13/4" 12.89*BKF7 is white

POLYPROPYLENE BULKHEAD FITTINGSThey are similar to, but softer than, the PVC bulkhead fittings. These female threaded bulkhead fittings are great for most bulkhead applications. One EPDM gasket included.


TF1 GK2 1/2" FIPT FIPT 13/4" 3/8" $6.09TF2 GK2 3/4" FIPT FIPT 13/4" 1/2" 6.09TF3 GK3 1" FIPT FIPT 2" 1/2" 7.29TF4 GK4 11/4" FIPT FIPT 29/16" 1/2" 8.59TF5 GK4 11/2" FIPT FIPT 29/16" 1/2" 8.59TF6 GK5 2" FIPT FIPT 31/4" 3/4" 10.39TF7 GK6 3" FIPT FIPT 41/2" 1" 19.69TF8 GK7 4" FIPT FIPT 55/16" 23/4" 47.09

MODEL GASKET# SIZE F B D L EACH

35012L GK1 1/2" FIPT FIPT 13/8" 22/25" $17.2935034L GK2 3/4" FIPT FIPT 15/8" 22/25" 21.7935100L GK3 1" FIPT FIPT 17/8" 22/25" 23.0935114L GK4 11/4" FIPT FIPT 23/4" 2" 31.5935112L GK4 11/2" FIPT FIPT 23/4" 2" 34.3935200L GK5 2" FIPT FIPT 31/4" 2" 44.4935300L GK6 3" FIPT FIPT 41/2" 23/25" 78.8935400L GK7 4" FIPT FIPT 53/4" 29/20" 146.2936012L GK1 3/4" SLIP FIPT 13/8" 22/25" 15.0936034L GK2 3/4" SLIP FIPT 15/8" 22/25" 16.6936100L GK3 1" SLIP FIPT 17/8" 22/25" 18.3936114L GK4 11/4" SLIP FIPT 23/4" 2" 24.4936112L GK4 11/2" SLIP FIPT 23/4" 2" 24.4936200L GK5 2" SLIP FIPT 31/4" 2" 36.1936300L GK6 3" SLIP FIPT 41/2" 23/25" 71.2936400L GK7 4" SLIP FIPT 53/4" 29/20" 131.09

ECONOMICAL PLASTIC BULKHEAD FITTINGSMade of ABS plastic. One EPDM gasket included.


BKF121 Q10G 1/2" SLIP SLIP 11/8" 3/4" $4.49

BKF122 Q10G 1/2" SLIP FIPT 11/8" 3/4" 4.49

BKF123 Q10G 1/2" FIPT SLIP 11/8" 3/4" 4.49

BKF124 Q10G 1/2" FIPT FIPT 11/8" 3/4" 4.49

BKF341 GK1 3/4" SLIP SLIP 13/8" 1" 5.19

BKF342 GK1 3/4" SLIP FIPT 13/8" 1" 5.19

BKF343 GK1 3/4" FIPT SLIP 13/8" 1" 5.19

BKF344 GK1 3/4" FIPT FIPT 13/8" 1" 5.19

BKF10 GK2 1" SLIP SLIP 13/4" 11/2" 5.59BKF11 GK2 1" SLIP FIPT 13/4" 11/2" 5.59BKF12 GK2 1" FIPT SLIP 13/4" 11/2" 5.59BKF13 GK2 1" FIPT FIPT 13/4" 11/2" 5.59BKF1120 GK4 11/2" SLIP SLIP 23/8" 13/4" 6.59BKF1121 GK4 11/2" SLIP FIPT 23/8" 13/4" 6.59BKF1122 GK4 11/2" FIPT SLIP 23/8" 13/4" 6.59BKF1123 GK4 11/2" FIPT FIPT 23/8" 13/4" 6.59BKF20 GK5 2" SLIP SLIP 27/8" 115/16" 7.79BKF21 GK5 2" SLIP FIPT 27/8" 115/16" 7.79BKF22 GK5 2" FIPT SLIP 27/8" 115/16" 7.79BKF23 GK5 2" FIPT FIPT 27/8" 115/16" 7.79

BKF10

Flange Side (E)

Gasket

Nut



359SECTIONProducts / Products / Products

359

BOTTOM DRAINSAquadyne Rhino Bottom Drains are machine manufactured from schedule 80 PVC materials, with NO injection molding. All Rhino drains can be installed with extreme confidence in any application by first time installers or experienced professionals. Rhino drains are installed in aquatic environments from ponds, water features, public aquariums, zoos, hatcheries, research facilities, aquaponics and quarantine systems. A bottom drain is one of the most important parts of a water installation, in that it’s integrity is paramount to the success of the entire project. One-year warranty. • Thicker flanges and liner attachment ring that will not flex, distort or crack• All attachments are precision machine fitted for extra strength with no need

for gap filling• Thermally welded joints provide extreme durability in the most

demanding environments• No injection molded components which would weaken the structureRhino I - Inline vertical drains with 12” anti-vortexing coverRhino Retro - Over the liner, no cut, retrofit drains for environments without bottom drains, or for those who do not want to install a through the liner drainRhino I OFS – Threaded for an over flow standpipe or a side wall returnRhino II - Heavy duty commercial drain with air diffuser and 4” return

359


RHINO IBDRH12 2” BOTTOM DRAIN 5 $82.99BDRH13 3” BOTTOM DRAIN 5 82.99BDRH14 4” BOTTOM DRAIN 5 88.19

RHINO RETROBDRTO2 2” ABOVE THE LINER DRAIN 7 93.49BDRTO3 3” ABOVE THE LINER DRAIN 7 103.99

RHINO I OFSBDOFS2 2” OVERFLOW DRAIN OR SIDEWALL RETURN 6 93.49BDOFS3 3” OVERFLOW DRAIN OR SIDEWALL RETURN 6 103.99BDOFS4 4” OVERFLOW DRAIN OR SIDEWALL RETURN 6 135.49

RHINO IIBDRH2A 4” BOTTOM DRAIN W/ AIR DIFFUSER 24 376.99BDRH2O 4” BOTTOM DRAIN W/O AIR DIFFUSER 23 324.49

TANK FITTING KITSAn inlet strainer and elbow are included with these color-coordinated bulkhead kits. The in/out fits standard PVC pipe, so you can make many variations of your own. Bulkheads are also available separately. The kit includes bulkhead, 90° elbow and inlet screen, which fits both sides of the bulkhead. Black is standard.

MODEL GASKET# DIA. L EACH 10+

TFK1 Q10G BULKHEAD KIT, 1/2" 11/8" 3/4" $7.29 $6.56TFO1 Q10G BULKHEAD ONLY, 1/2" 11/8" 3/4" 5.29 4.76TFK2 GK1 BULKHEAD KIT, 3/4" 13/8" 11/4" 7.79 7.01TFO2 GK1 BULKHEAD ONLY, 3/4" 13/8" 11/4" 5.79 5.21TFK3 GK2 BULKHEAD KIT, 1" 13/4" 2" 8.19 7.37TFO3 GK2 BULKHEAD ONLY, 1" 13/4" 2" 5.99 5.39

PLUMBINGTank Fitting Kits/Drains

TFK3

BOTTOM DRAIN This 4” bottom drain is for use in liner ponds and concrete ponds. Its antivortex drain cover forces water to enter from the bottom of the pond, and its large intake helps reduce pump pressure. SAE standard pipe connection, use with 4” PVC. Offset suction port creates a swirl action that helps remove debris. Includes everything you need for easy liner installation.

RHINO I

RHINO I OFS

RHINO RETRO

RHINO II

MODEL EACH

SBD4 $84.59

REPLACEMENT BULKHEAD FITTING GASKETSMade of EPDM material. One gasket is included in all of the bulkhead fittings on page 358. For most applications, only one gasket is needed which is located on the flange side whether or not the flange side is on the water side.

MODEL EACH

GK1 $1.89GK2 1.19GK3 1.39GK4 1.39GK5 1.79GK6 3.09GK7 29.69Q10G .75

GK5

Drain TipIf you reuse your drain water, it's best if you gravity flow it to your filter, as a pump will puree it and make it much harder to filter out. But don't make your drain piping too large in diameter. If the water travels too slowly, waste will settle in the pipe. You should always have a dump valve at the end of the drain pipe. When you open it, a surge of high velocity water will scour out all settled material and prevent it from contaminating your recirculated water.




TEE ELIMINATORSHere is a hard-to-find, cost-saving fitting. A PVC 3” x 3/4” reducing tee costs about $10. These tee eliminators can do the same thing for under a buck. Just drill a hole, press in a tee eliminator, then thread in your pipe. Made of flexible PVC with female pipe threads. They work in all rigid pipe materials with pipe walls between 1/8” and 1/4” thick (use holesaws).

MODEL FPT SIZE MIN. PIPE I.D. HOLE SIZE EACH

FC32 1/2" 1" 1" $.75FC34 3/4" 11/4" 1-3/16” .90

FC36 1" 11/2" 1 7/16” 1.09

360 PLUMBINGPlugs/Couplings/Caps

EP1 End Plug

EP4 Pipe Plug

HT4D

Hand Tite® is a registered trademark of R. Tim Graham.

FC36

MODEL PVC PIPE SIZE EACH

FC1 11/4" x 11/4" $5.99FC2 11/2" x 11/4" 6.89FC3 11/2" x 11/2" 7.49FC4 2" x 11/2" 8.29FC5 2" x 2" 8.99FC6 3" x 11/2" 9.99FC7 3" x 2" 10.59

MODEL PVC PIPE SIZE EACH

FC8 3" x 3" $11.29FC9 4" x 11/2" 12.29FC10 4" x 2" 12.99FC11 4" x 3" 13.29FC12 4" x 4" 13.99FC13 6" x 4" 26.99FC14 6" x 6" 28.99

EXPANSION PLUGSExpansion plugs are suitable for all low- and medium-pressure water applications. A simple twist of the wingnut will produce a watertight seal. The 11/2”, 2” and 3” plugs fit the end of pipes only. The 4”, 6” and 8” plugs can also be inserted into the pipe.

MODEL NOMINAL PIPE SIZE PRESSURE EACH

EP1 11/2" END PLUG 40' HEAD $5.39EP2 2" END PLUG 40' HEAD 6.49EP3 3" END PLUG 40' HEAD 8.39EP4 4" PIPE PLUG 40' HEAD 10.69EP6 6" PIPE PLUG 30' HEAD 23.69EP8 8" PIPE PLUG 30' HEAD 50.09

FLEXIBLE COUPLINGSThese couplings are extremely useful for adapting different materials and sizes, making temporary connections or for permanent connections that must allow some movement. Not FDA-approved for potable water. Clamps are included. Use in low-pressure applications only.

QUICK CAPSFor testing or easy cleanout of low-pressure piping. Clamp included.

MODELPVC PIPE

SIZE EACH

QC1 11/2" $6.39QC2 2" 7.19QC3 3" 8.79QC4 4" 11.49QC5 6" 16.19QC6 8" 32.49

HAND TITE® EXPANSION PLUGS This reusable Hand Tite expansion plug is excellent for many applications and can be used in any pipe, including plastic, clay and iron. It seals the bell and spigot ends of pipes as well as jagged holes. Plugs are made of nylon and rubber and can be used in salt water. No tools required for installation.

MODEL PIPE SIZE EACH

HT4D 4" $15.09HT6D 6" 17.39HT8D 8" 41.89HT10D 10" 121.79HT12D 12" 140.69



361PLUMBINGHose/Clamps

361

STAINLESS STEEL HOSE CLAMPSYou can find clamps for less, but then they must be replaced when the screw rusts away. These quality clamps are all stainless steel (#301SS band) including the screw (#410SS)! The one-piece housing is locked to the band without spot welds. The band is 9/16” wide (5/16” on SSAA) and the screw has both a slotted head and a 5/16” hex. Choose clamps with a larger maximum diameter than the outside diameter (O.D.) of the tubing that it will be holding.

DIAMETER

MODEL SIZE MINIMUM MAXIMUM EACH

SSAA 1/4" 0.22" 0.62" $1.09SSA 1/2" 0.38" 0.88" 1.29SSB 3/4" 0.50" 1.06" 1.39SSC 1" 0.75" 1.75" 1.49SSD 11/4" 1.00" 2.00" 1.49SSE 11/2" 1.25" 2.25" 1.49SSF 2" 1.50" 2.50" 1.69SSG 21/2" 2.25" 3.25" 1.79SSH 31/2" 2.50" 4.50" 1.79

SSI 4" 3.00" 5.00" 2.19

SSJ 5" 4.50" 6.50" 3.39

SUCTION/DISCHARGE HOSEThis PVC hose is externally ribbed with smooth inside surfaces. It weighs about half that of rubber suction hose. Rated at 28” Hg vacuum at 68ºF. Its small bend radius (see below) and high strength will give reliable service for pumping, siphoning, fish hauling, etc. Full rolls are 100 feet.

ACTUAL MAX MINIMUM MAX* SHIP WT/FOOT MODEL I.D. PSI BEND RADIUS LENGTH (LBS) EACH

SH4 11/2" 90 6" 100' 0.5 $2.99/FTSH5-AQ 2" 70 9" 50' 0.7 4.29/FTSH6 3" 60 13" 20' 1.3 7.09/FT

SH8 4" 50 18" 8' 2.1 11.19/FT

*Maximum per ground carton; 100’ Maximum by truck.

A502

ACTUAL SHIP WT/100’ MODEL I.D. (LBS) EACH

A50112 11/2" 16 $.95/FTA502 2" 23 1.19/FTA503 3" 39 1.79/FT

A504 4" 52 1.99/FT

DISCHARGE HOSEThis is a good quality, polyvinyl-coated discharge hose. It is UV-resistant for extra long life outdoors. It lies flat when not in use, which allows easy storage and handling. The maximum roll length is 300’, but we will cut it to any size for you.

UNISEAL® RUBBER SEALWhy use an expensive bulkhead when you can use a Uniseal®? Just drill a hole in the pipe, tank or bucket, insert a Uniseal®, then put some window cleaner on the end of the pipe and push it in. Feels like rubber, but they are made of MPR, rated to 40 psi and warranted for 25 years. They are immune to cold, will not harden and hold pressure and vacuum. The sizes below correspond to standard Schedule 40 PVC pipe. Fit tank wall thicknesses up to 1/2”.

MODEL PIPE SIZE PIPE O.D. HOLESAW SIZE EACH

U050 1/2" .84" 11/4" $1.59U075 3/4" 1.05" 11/4" 1.69U100 1" 1.31" 13/4" 1.99U125 11/4" 1.66" 2" 2.39U150 11/2" 1.90" 21/2" 2.69U200 2" 2.37" 3" 4.69U300 3" 3.50" 4" 5.09U400 4" 4.50" 5" 6.29U600 6" 6.62" 7" 7.79

Tank Wall

Push PipeFrom This Side

Pipe

Uniseal® is a registered trademark of Uniseal, Inc.



PLASTIC CLAMPS FOR VINYL TUBINGThese quick ratcheting, noncorroding clamps work very well on vinyl tubing. They tighten by hand or with pliers and are releasable/reusable. Not for high-pressure applications. Maximum diameters shown are with two teeth engaged. UV-resistant.

MODEL CLAMP MINMAXIMUM DIAMETER

FITS VINYL TUBING PART NO. EACH

SNP2 0.35" 0.39" TV40 $.50SNP6 0.45" 0.51" TV60 .75SNP10 0.57" 0.65" TV70/TVR60 .75SNP14 0.70" 0.80" TV80/TVR70 .75SNP19 0.86" 1" TVR80 .75SNP24 1" 1.13" TV90/TVR90 .99

PIPE HANGERSHangers can be mounted on the floor, wall or overhead. After all the hangers are attached, push pipe into the open jaws, and a sharp “click” signals that it is locked in place. They also release easily. Meets UPC (Uniform Plumbing Code) specifications. Sizes below fit PVC, CPVC, ABS, PE, PP, PB and fiberglass pipe nominal sizes. Temperature range: -40 to 180°F. Reusable.MODEL EACH

CP4 1/2” $.99CP6 3/4” 1.49CP7A 1” 1.99CP8 11/4” 2.79CP9 11/2” 3.59CP10A 2” 4.49CP11A 21/2” 6.69CP12A 3” 9.89CP13A 4” 17.69


362 PLUMBINGPipe Hangers/Supports/Clamps/PVC Pipe

CP14

SNP2

CP7A

COLORID

(IN)PSI @70º F

MAX BEND RADIUS

SOLD PER FOOTMODEL EACH

SOLD PER ROLLMODEL LENGTH

SHIP WTLBS EACH

WHITE ½ 100 2" FPP12F $1.49 FPP12 100' 14 $71.19

WHITE ¾ 100 2" FPP34F 1.69 FPP34 100' 17 105.89

WHITE 1½ 65 5" FPP112F 2.49 FPP112 50' 23 77.69

BLACK ½ 100 2" BFPP12F 1.09 BFPP12 100' 14 102.69

BLACK ¾ 100 2" BFPP34F 1.29 BFPP34 100' 17 133.19BLACK 1 100 3" BFPP1F 1.79 BFPP1 50' 13 62.69BLACK 1¼ 80 4" BFPP114F 1.89 BFPP114 50' 22 81.19BLACK 1½ 65 5" BFPP112F 2.19 BFPP112 50' 23 87.09

BLACK 2 60 6" BFPP2F 3.19 BFPP2 50' 32 130.69


235 FLEXIBLE PVC PIPE SOLVENT CEMENT (½ PINT CAN) 0.6 $10.49HAZMAT A

PVC PIPE SUPPORTS These inexpensive pipe clamps are ideal for floor and wall mounting but not for overhead mounting of water pipes. They fit standard PVC pipe. A single screw (not included) mounts each pipe support.

PVC SADDLEOur straight PVC saddle is easy to install. Just drill a 3/8” hole into 1/2” PVC pipe and secure the saddle in place with PVC glue. 1/8” FNPT threads.

MODEL EACH

VS1 STRAIGHT SADDLE $1.39

VS1 W/VBR12

Brass Valve Not Included

FLEXIBLE PVC PIPE - SCHEDULE 40This flexible Schedule 40 PVC pipe permits compound curves, greatly reducing the number of fittings otherwise required. It also reduces friction loss caused by elbows. Standard Schedule 40 or 80 PVC fittings can be used. A special solvent cement (235) is required (do not use purple primer—use acetone as a pipe primer).

MODEL EACH

CP14 BLACK, 11/2” $1.39CP15 WHITE, 2” 1.69



363

SILICONE TUBING, AQUARIUM Extremely flexible, kink-resistant, UV- and tear-resistant, nontoxic, tinted light blue and affordable, this high quality silicone tubing could become your favorite aquarium tubing. Autoclavable. Temperature range -80 to 500°F. Its 1/8” I.D. fits aquarium devices and 3/16” barbed fittings.

VALVE FOR SILICONE TUBINGPrecision ABS, special low-cost roll clamp, for use with silicone tubing, has flow regulating accuracy compatible to needle valve. Design allows for precise and uniform flow control of air or liquids and stays where it’s set. It will only work with our silicone tubing.

BLACK AND WHITE VINYL TUBING Opaque (non-transparent) tubing blocks sunlight to eliminate algae growth when used for water delivery. Black hides well in garden ponds, etc. Working pressures same as clear tubing above.

BTV40 WTV70BTV70BTP30HD WTP30HD WTV40 WTV60

MODEL LENGTH EACH

TP30S 100’ $56.69

MODEL EACH

290 $.25

PLUMBINGSilicone Tubing/Valve/Vinyl Tubing

363

CLEAR RIGID TUBINGRigid tubing is ideal for microalgae and zooplankton culture tanks where aeration is required at the bottom of the tank. This is a thin-walled (only .020" to .030" thick), rigid, "straw-like" tube. Sold in 36" length. To extend length, use a piece of vinyl tubing as a coupler.

16025

16045

MODEL LENGTH O.D. FITS TUBING EACH 6+

16005 36" 3/16" TP30 $2.89 $2.3116010 36" 5/16" TV40 2.99 2.3916015 36" 3/8" TV60 3.09 2.4716025 36" 1/2" TP70 3.99 3.1916035 36" 5/8" TV80 5.59 4.4716040 36" 3/4" TV90 6.99 5.5916045 36" 1" TV100 7.49 5.99

1600516015

SOLD PER FOOT SOLD PER ROLLCOLOR ID OD MODEL EACH MODEL LENGTH SHIP WT (LBS) EACH

BLACK 3/16” 5/16” BTP30HDF $.50 BTP30HD 100’ 4 $25.99BLACK 1/4” 3/8” BTV40F .55 BTV40 100’ 4 31.49BLACK 1/2” 5/8” BTV70F .85 BTV70 100’ 8 56.29WHITE 3/16” 5/16” WTP30HDF .50 WTP30HD 100’ 4 29.39WHITE 1/4” 3/8” WTV40F .55 WTV40 100’ 4 33.89WHITE 3/8” 1/2” WTV60F .65 WTV60 100’ 5 48.19WHITE 1/2” 5/8” WTV70F .70 WTV70 100’ 8 52.69



364 PLUMBINGClear PVC Pipe/Fittings/Tubing

CLEAR PVC PIPE If you need to see what is going on inside your pipes, this clearly is what you need (does have slight blue tint). Use economical short lengths to see the degree of microbial growth inside the piping or build entire clear systems for research, prototypes, oxygen saturators, etc.This clear PVC pipe is FDA-approved for food contact applications. May be cold sterilized in ethylene oxide. It is fully compatible with regular Schedule 40 PVC pipe fittings. Install with regular PVC cement. Use compression couplings, flexible couplings or unions to facilitate cleaning.Sold by the foot, 6’ length maximum. Lengths 5’ and over ship Oversize.

MODEL NOMINAL PIPE SIZE MAX PSI ACTUAL O.D. WEIGHT PER FOOT FOOT

C100-AQ 1/2" 300 0.8" .1 lb $3.19C101 3/4" 240 1.1" .1 lb 3.99C102 1" 220 1.3" .2 lb 4.99C103 11/4" 180 1.7" .2 lb 7.79C104 11/2" 170 1.9" .2 lb 8.89C105 2" 140 2.4" .3 lb 11.19C106 3" 130 3.5" .4 lb 24.79C107 4" 110 4.5" .6 lb 34.79C108 6" 45 6.6" 1.0 lb 61.29373 PVC CEMENT, 1 PINT 9.59Note: there is a cut fee. First cut is free; each cut thereafter is $1.00

Coupling

90° Elbow

Tee

TA3

TAGL

CLEAR PVC FITTINGSSchedule 40 PVCLike the clear PVC above, these slip PVC fittings use regular PVC cement (373).

TEES

C401005 1/2" $9.19C401007 3/4" 10.39C401010 1" 17.59C401015 11/2" 35.69C401020 2" 50.89

90º ELBOWS

C406005 1/2" 8.09C406007 3/4" 6.79C406010 1" 14.89C406015 11/2" 23.89C406020 2" 41.79

COUPLING

C429005 1/2" 4.59C429007 3/4" 6.69C429010 1" 10.69C429015 11/2" 17.59C429020 2" 21.99

ACRYLIC TUBINGThis extruded acrylic tubing has only a 1/8” (3.2 mm) thick wall and is much clearer and lighter than our clear PVC pipe. Standard PVC cement can be used to bond acrylic tubing to PVC for most low-pressure applications. TAGL is light-bodied; allow 24 hours to cure fully. Sold and priced by the foot. Only TA4 and TA5 are compatible with PVC sockets.

MODEL APPROXIMATE SIZE FITS PVC SOCKET FOOT

TA3 2" O.D. — $5.39TA4 31/2" O.D. 3" 10.19TA5 41/2" O.D. 4" 15.19TAGL ACRYLIC CEMENT — 8.79

Note: there is a cut fee. First cut is free; each cut thereafter is $1.00

TT18

TYGON S3® E-3603 FLEXIBLE TUBINGSpecifically formulated for lab use, this flexible tubing works with almost any inorganic chemical. Flexible and clear, it is noncontaminating, autoclavable and ideal for liquid and ozone gas transmission.

Tygon S3® is a registered trademark of Saint-Gobain Performance Plastics Corp.

ID OD SOLD PER FOOT SOLD PER 50’ ROLL (IN) (IN) MODEL EACH MODEL EACH

1/8 1/4 TT18F $1.29 TT18 $53.59 3/16 5/16 TT316F 1.89 TT316 75.59 1/4 3/8 TT14F 2.29 TT14 92.39 3/8 1/2 TT38F 3.79 TT38 155.39 5/8 13/16 TT58F 6.29 TT58 262.49 3/4 1 TT34F 7.89 TT34 362.29



365PLUMBINGClear Vinyl Tubing/Cutters/Lead Weight

365

All our nonreinforced tubing is marked every 12" for easy measuring. Reinforced tubing has a higher pressure rating.

CLEAR VINYL TUBING FDA-approved clear vinyl tubing. Our aquarium tubing (TP30) is a very high quality product with a slightly larger I.D. and heavier wall than the typical 1/8” I.D. aquarium tubing. This tubing is rated at 36 psi @ 72°F (22°C). Note: Vinyl tubing is not recommended for use with pure oxygen or ozone.

TV100 TV40 TP30HD TP30

MAX WORKING SOLD PER FOOT SOLD PER COIL INSIDE DIAMETER OUTSIDE DIAMETER WALL PRESSURE COIL SHIP WTINCHES MM INCHES MM THICKNESS @ 90ºF MODEL EACH MODEL LENGTH (LBS) EACH

5/32 4.0 1/4 6.4 1/16" 30 PSI TP30F $0.30 TP30 500’ 6 $66.39 3/16 4.8 5/16 7.9 1/8" 40 PSI TP30HDF 0.40 TP30HD 100’ 4 22.59 1/4 6.4 3/8 9.5 1/8" 40 PSI TV40F 0.65 TV40 100’ 4 26.09 3/8 9.5 1/2 12.7 1/8" 30 PSI TV60F 0.55 TV60 100’ 5 30.99 1/2 12.7 5/8 15.9 1/8" 30 PSI TV70F 0.65 TV70 100’ 8 39.29 5/8 15.9 3/4 19.1 1/8" 20 PSI TV80F 0.99 TV80 100’ 8 74.09 3/4 19.1 1 25.4 1/4" 20 PSI TV90F 1.69 TV90 100’ 21 117.09 1 25.4 11/4 31.8 1/4" 15 PSI TV100F 2.09 TV100 100’ 26 155.19 11/4 31.8 11/2 38.1 1/4" 15 PSI TV125F 3.69 TV125 100’ 30 320.89

TVR150 TVR125 TVR90TVR100TVR200

REINFORCED CLEAR VINYL TUBINGSynthetic, fiber-reinforced, food-grade tubing preferred for its kink resistance, high-pressure rating and flexibility. Tough, flexible, polyvinyl tubing has excellent clarity, is odorless and nontoxic. Temperature range -48 to 160°F. Note: Vinyl tubing is not recommended for use with pure oxygen or ozone.

LEAD WEIGHT

SOFT TUBING CUTTERSThese handy cutters are great for cutting vinyl tubing, rubber hose, polyethylene, rope and other soft materials. The KT100 cuts up to 1” outside diameter tubing, while the KT200 cuts up to 2” in diameter. Plastic body with stainless steel blade.

MODEL EACH

KT100 1” CUTTER $17.49KT200 2” CUTTER 19.69

KT100

LEAD WEIGHTUse these 1-oz lead weights with Vinyl Clear Tubing, model TP30, to counteract the buoyancy of air tubing if diffusers are more than 30" deep.

MODEL EACH

LEAD 1 OZ. LEAD WEIGHT $0.40

MAX WORKING SOLD PER FOOT SOLD PER COIL INSIDE DIAMETER OUTSIDE DIAMETER WALL PRESSURE COIL SHIP WTINCHES MM INCHES MM THICKNESS @ 90ºF MODEL EACH MODEL LENGTH (LBS) EACH

.250” 6.4 .380” 9.7 .06” 120 PSI TVR40F $0.99 TVR40 50’ 3 $34.69

.375” 9.5 .600” 15.1 .112” 120 PSI TVR60F 1.19 TVR60 50’ 4 49.39

.500” 12.7 .750” 9.1 .125” 100 PSI TVR70F 1.49 TVR70 50’ 6 64.19

.625” 15.9 .875” 22.2 .125” 100 PSI TVR80F 1.99 TVR80 50’ 7 78.79

.750” 19.1 1.025” 26.0 .137” 80 PSI TVR90F 2.39 TVR90 50’ 9 95.291.00” 25.4 1.312” 33.3 .156” 80 PSI TVR100F 3.19 TVR100 50’ 8 138.691.25” 31.8 1.687” 42.9 .218” 60 PSI TVR125F 4.79 TVR125 50’ 30 194.891.50” 38.1 1.88” 47.8 .19” 60 PSI TVR150F 6.69 TVR150 50’ 30 264.292.00” 50.8 2.50” 63.5 .25” 40 PSI TVR200F 11.09 TVR200 50’ 51 372.69



62014B

62022B

62005B

ZBN54

FLEXIBLE BLACK MODULAR PIPINGThis modular piping snaps together for use in tanks and aquariums (expect some joint leakage). Its unique ball-socket joint design makes it extremely flexible and enables the creation of custom flow patterns in tanks.

MODEL EACH

JT1 1/2" FLEX. JOINT TUBING, 6" $4.19JT2 1/2" ROUND NOZZLE 1.59JT3 1/2" 90° NOZZLE 2.19JT4 1/2" MPT CONNECTOR 1.59JT5 1/2" Y FITTING 3.49JT6 1/2" ELBOW FITTING 3.09JT7 1/2" MPT VALVE 9.69JT8 1/2" FPT VALVE 8.19JT9 1/2" IN-LINE VALVE 9.39JT10 1/2" MULTINOZZLE, 15 FLOWS 30.69JT11 1/2" X 1.2" FLARED NOZZLE 3.29JT12 3/4" FLEX. JOINT TUBING, 6" 5.19JT13 3/4" ROUND NOZZLE 1.69JT14 3/4" MPT CONNECTOR 1.79JT15 3/4" Y FITTING 7.09JT16 3/4" F X 1/2" M ADAPTER 3.49JT17 3/4" X 3" FLARED NOZZLE 6.39

78002 ASSEMBLY PLIERS FOR 1/2" TUBING 15.79

78004 ASSEMBLY PLIERS FOR 3/4" TUBING 26.29

THREAD CUTTING TAPSThese taps will cut pipe threads (FNPT) in PVC, mild steel, etc. Use with bits shown below to save the cost of tees, saddles and adapters.

MODEL EACH

BNT1 TAP, 1/8" NPT $7.59BNT2 TAP, 1/4" NPT 7.99BNT3 TAP, 3/8" NPT 10.49BNT4 TAP, 1/2" NPT 15.99BNT5 TAP, 3/4" NPT 23.39

BT1BNT1

DRILL BITS

MODEL EACH

BT1 BIT, 11/32" FOR 1/8" NPT $3.89BT2 BIT, 7/16" FOR 1/4" NPT 5.19BT3 BIT, 9/16" FOR 3/8" NPT 14.79BT4 BIT, 23/32" FOR 1/2" NPT 23.09BT5 BIT, 15/16" FOR 3/4" NPT 34.29

BRASS ADAPTERS These high-quality, brass, male adapters will work at high temperatures to 150 psi. Model 62025B has 3/4” nominal female pipe thread. They are made of CA360, CA345 or CA370 brass for years of continuous use. Note: Barb sizes are “nominal” (1/2” = .62” actual).MODEL MALE ADAPTERS EACH

62001B* 1/8" NPT X 3/16" BARB $0.9962007B 1/8" NPT X 1/4" BARB 1.3962009B 1/8" NPT X 3/8" BARB 1.3962005B* 1/4" NPT X 3/16" BARB 1.6962006B 1/4" NPT X 1/4" BARB 1.4962008B 1/4" NPT X 3/8" BARB 1.4962010B 1/4" NPT X 1/2" BARB 1.5962014B 1/2" NPT X 1/4" BARB 3.2962016B 1/2" NPT X 3/8" BARB 3.4962018B 1/2" NPT X 1/2" BARB 3.19ZBN54** 1/2” NPT X 5/8” BARB 3.4962021B 3/4" NPT X 3/8" BARB 4.1962022B 3/4" NPT X 1/2" BARB 4.3962024B 3/4” NPT X 3/4” BARB 6.69

MODEL FEMALE ADAPTERS EACH

62025B 3/4” FNPT X 3/4” BARB 9.99

*Use with TP30HD tubing only. **Reducing style.

JT1/JT12

JT10

JT15 JT7

JT4/JT14

JT3 JT6

JT9 JT8

JT11 JT2/JT13

366 PLUMBINGBrass Adapters/Modular Piping/Taps/Drill Bits

62025B


PLUMBINGTubing Adapters and Fittings

367

Tee Barb x Barb x Barb

Male Adapter NPT x Barb

Connector Barb x Barb

Elbow NPT x Barb

Elbow Barb x Barb

Tee Adapter NPT x Barb x Barb

Standard StyleCONNECTOR (BARB X BARB) EACH

101A $.95101B 1.09101C 1.09101D 2.39101E 1.99101F 3.89

BARB SIZEFITS

TUBING MODELS BARB SIZE FITS

TUBING MODELS

3/16" TP30, TP30HD 3/8" TV60, TVR601/4" TV40, TVR40 1/2" TV70, TVR70

MALE ADAPTER(MNPT X INSERT) EACH

103A $.75103B 1.09103C 1.19103D 1.79103E 1.99103F 3.89

90º ELBOW(BARB X BARB) EACH

105A $1.79105B 2.19105C 2.49105D 2.79105E 3.29105F 4.49

TEE (BARB X BARB

X BARB) EACH

107A $1.99107B 2.19107C 2.79107D 4.39107E 5.49107F 9.79

FEMALE ADAPTER

(FNPT X BARB) EACH

117A $3.99117B 4.39117C 4.89117D 5.99117E 7.59117F 9.69

90º ELBOW(BARB X MNPT) EACH

113A $2.29113B 3.19113C 4.19113D 5.49113E 7.29113F 11.59

101

113

103

105

117

107

Male Adapters, Low Cost

MODEL EACH

62001-2 1/8" NPT x 3/16" BARB $.3062007-2 1/8" NPT x 1/4" BARB .3062009-2 1/8" NPT x 3/8" BARB .30

62007-2

62009-2

62001-2

POLY TUBING INSERT FITTINGS, 5/8”–2”Use these insert fittings for repairing, adapting or connecting black poly tubing. Connections under stress or pressure will require hose clamps. These insert fittings fit the nominal sizes of polyethylene tubing; for instance, a 5/8” fitting fits tubing with 0.62” I.D. Use letter following part no. to indicate size (A=5/8”, B=3/4”, C=1”, D=11/4”, E=11/2”, F=2”).

CONNECTORS MODEL EACH

3/16" BARB x 3/16" BARB 62068 $.651/4" BARB x 3/16" BARB 62053 .601/4" BARB x 1/4" BARB 62069 .551/2" BARB x 1/4" BARB 62055 .853/8" BARB x 1/4" BARB 62054 .553/8" BARB x 3/8" BARB 62071 .551/2" BARB x 3/8" BARB 62052 .555/8" BARB x 3/8" BARB 62051 .851/2" BARB x 1/2" BARB 62072 .605/8" BARB x 1/2" BARB 62050 1.19

90º ELBOWS MODEL EACH

1/8" NPT x 3/16" BARB 62001L $.801/8" NPT x 1/4" BARB 62007L .801/2" NPT x 1/4" BARB 62085 .991/8" NPT x 3/8" BARB 62009L .901/2" NPT x 3/8" BARB 62086 .991/2" NPT x 1/2" BARB 62087 .991/4" BARB x 1/4" BARB 62080 .803/8" BARB x 3/8" BARB 62081 .801/2" BARB x 1/2" BARB 62082 .85

TEES MODEL EACH

3/16" BARB 62063 $.751/4" BARB 62064 .803/8" BARB 62065 .801/2" BARB 62067 .951/8" NPT x 3/16" x 3/16" 62056 1.291/4" NPT x 1/2" x 1/2" 62122 1.291/2" NPT x 1/2" x 1/2" 62123 1.09

MALE ADAPTERS MODEL EACH

1/8" NPT x 3/16" BARB 62001 $.401/4" NPT x 3/16" BARB 62005 .45

1/2" NPT x 3/16" BARB 62013 .70

1/8" NPT x 1/4" BARB 62007 .401/4" NPT x 1/4" BARB 62006 .401/2" NPT x 1/4" BARB 62014 .603/4" NPT x 1/4" BARB 62020 1.191/8" NPT x 3/8" BARB 62009 .601/4" NPT x 3/8" BARB 62008 .401/2" NPT x 3/8" BARB 62016 .603/4" NPT x 3/8" BARB 62021 .851/4" NPT x 1/2" BARB 62010 .651/2" NPT x 1/2" BARB 62018 .653/4" NPT x 1/2" BARB 62022 .95

TUBING ADAPTERS, 1/8”–3/4”These polyethylene, precision-injected, molded fittings are high strength, chemically inert and noncorroding. Approved by the National Sanitation Foundation (NSF) for use with liquids for human consumption. Temperature range: -65 to 190°F. Working pressure up to 120 psi. Shipping weight is 1 lb per 100. Check with us for special fittings not listed (in 50-piece lots only). Barb sizes shown fit the following tubing sizes.


368 PLUMBINGReducers

111

110

109

119

122

112

62028

62075

62083

REDUCER STYLEReducing Male Adapter (Barb x MNPT) MODEL EACH

111A 3/4" X 1/2" $2.89111B 1" X 3/4" 2.99

Reducing Male Adapter (MNPT x Barb) MODEL EACH

110A 3/4" X 1/2" $2.59110B 1" X 3/4" 2.691436075 1/2” X 1” 2.99

Reducing Tee (Barb x Barb x Barb) Note: Last dimension is center.

MODEL EACH

112A 3/4” X 3/4” X 5/8” $2.39112B 1” X 1” X 5/8” 2.89112C 1” X 1” X 3/4” 2.89

MODEL EACH

62075 1/4” NPT X 1/4” NPT $ 0.5562083 1/2” NPT X 1/4” NPT 0.70

MODEL EACH

62024 1/8” MALE NPT $0.3062025 1/4” MALE NPT 0.3062026 3/8” MALE NPT 0.3562027 1/2” MALE NPT 0.4562028 3/4” MALE NPT 0.75

Plugs

Nipples

90º Elbow (Barb x FNPT)MODEL EACH

119A 5/8” X 1/2” $2.09119B 3/4” X 1/2” 2.09119C 1” X 1/2” 2.19119E 3/4” X 3/4” 2.19119F 1” X 3/4” 2.59119H 1” x 1” 3.49

Reducing Tee (Barb x Barb x FNPT) Note: Last dimension is center.

MODEL EACH

122A 5/8" X 5/8" X 1/2" $2.19122B 3/4" X 3/4" X 1/2" 2.69122C 1" X 1" X 1/2" 3.49122D 1" X 1" X 3/4" 3.49122E 1" x 1" x 1" 2.69

Reducer Connector (Barb x Barb)MODEL EACH

109A 3/4" X 5/8" $1.49109B 1" X 3/4" 1.59109C 11/4" X 1" 2.49109D 11/2" X 11/4" 2.89109E 2" X 11/2" 4.69

LIVE CHATAvailable for your convenience:• General technical support & customer service• Online discussion with technician• Order questions & tracking • Multilingual chat options available • Billing & shipping questions



369369

A

BC

A B

C

TEE (SLIP X SLIP X SLIP) MODEL SIZE EACH

401005-AQ 1/2" $.35401007 3/4" .40401010 1" .75401012 11/4" 1.09401015 11/2" 1.39401020 2" 1.99401030 3" 8.69401040 4" 15.69

INSERT ADAPTER (INSERT X SLIP)MODEL SIZE EACH

474005-AQ 1/2" $1.19474007-AQ 3/4" 1.39474010-AQ 1" 1.49474012-AQ 11/4" 2.19

MODEL SIZE EACH

474015-AQ 11/2" $2.89474020-AQ 2" 5.29474030-AQ 3" 14.89474040-AQ 4" 16.99

INSERT ADAPTER (INSERT X SPIG)MODEL SIZE EACH

460005-AQ 1/2” $.95460007-AQ 3/4” 1.29460010-AQ 1” 1.29460012-AQ 11/4” 1.29

MODEL SIZE EACH

460015-AQ 11/2” $1.49460020-AQ 2” 2.39460030-AQ 3” 8.09460040-AQ 4” 9.29

REDUCING TEE (SLIP X SLIP X SLIP)

MODELSIZE

A B C EACH

401101-AQ 3/4" x 3/4" x 1/2" $1.09401126 1" x 3/4" x 1" 1.29401130 1" x 1" x 1/2" .80401131 1" x 1" x 3/4" .85401167 11/4" x 11/4" x 3/4" 1.19401168 11/4" x 11/4" x 1" 1.19401209 11/2" x" 11/2" x 1/2" 2.19401210 11/2" x 11/2" x 3/4" 2.19401211 11/2" x 11/2" x 1" 2.19401247 2" x 2" x 1/2" 2.09401248 2" x 2" x 3/4" 2.09401249 2" x 2" x 1" 2.09401251 2" x 2" x 11/2" 2.09401335 3" x 3" x 1" 9.39401336 3" x 3" x 11/4" 9.39401337 3" x 3" x 11/2" 9.39401338 3" x 3" x 2" 9.39401419 4" x 4" x 11/2" 15.69401420 4" x 4" x 2" 15.69401422 4" x 4" x 3" 15.69

TEE (SLIP X SLIP X FNPT)MODEL SIZE EACH

402005 1/2" $.45402007 3/4" .70402010 1" 1.29402012 11/4" 1.99402015 11/2" 2.69402020 2" 3.39402030 3" 12.99402040 4" 19.89

CROSSES (SLIP)MODEL SIZE EACH

420005 1/2" $0.99420007 3/4" 1.69420010 1" 2.09420012 11/4" 2.79420015 11/2" 3.19420020 2" 4.69420030 3" 12.29420040 4" 18.19

REDUCING TEES (SLIP X SLIP X FNPT)

MODELSIZE

A B C EACH

402071 1/2" x 1/2" x 1/8" $.99402101 3/4" x 3/4" x 1/2" .60402130 1" x 1" x 1/2" .90402131 1" x 1" x 3/4" 1.29402166 11/4" x 11/4" x 1/2" 2.09402167 11/4" x 11/4" x 3/4" 2.09402168 11/4" x 11/4" x 1" 2.09402209 11/2" x 11/2" x 1/2" 2.69402210 11/2" x 11/2" x 3/4" 2.69402247 2" x 2" x 1/2" 3.29402248 2" x 2" x 3/4" 3.29402249 2" x 2" x 1" 3.29402251 2" x 2" x 11/2" 3.29402335 3" x 3" x 1" 10.29402338 3" x 3" x 2" 10.29

TEE (FNPT X FNPT X FNPT)MODEL SIZE EACH

405005 1/2” $1.19405007 3/4” 1.89405010 1" 2.69

PLUMBINGTees/Crosses/Insert Adapters



370

90º ELL (SLIP X SLIP)MODEL SIZE EACH

406005 1/2" $.70

406007 3/4" .80

406010 1" .55406012 11/4" .99406015 11/2" .99406020 2" 1.59406030 3" 5.89406040 4" 10.49406060 6" 33.49

45º ELL (SLIP X SLIP)MODEL SIZE EACH

417005 1/2" $.45

417007 3/4" .70

417010 1" .85417012 11/4" 1.19417015 11/2" 1.49417020 2" 1.89417030 3" 7.69417040 4" 13.69417060 6" 33.89

CAP (SLIP)MODEL SIZE EACH

447005 1/2" $.25

447007 3/4" .30

447010 1" .45447012 11/4" .65447015 11/2" .70447020 2" .85447030 3" 2.89447040 4" 6.59447060 6" 15.79

CAP (FNPT)MODEL SIZE EACH

448005 1/2" $.50

448007 3/4" .60

448010 1" .90448012 11/4" 1.09448015 11/2" 1.09448020 2" 1.99448030 3" 3.79448040 4" 6.69

6” NIPPLE, GRAY SCHEDULE 80 PVCMODEL SIZE EACH

880060 1/4" $2.19

881060 3/8" 2.39

882060 1/2" 1.49883060 3/4" 1.89884060 1" 2.59885060 11/4" 3.09886060 11/2" 4.19887060 2" 5.99888060 21/2" 17.09889060 3" 22.89890060 4" 29.19

CLOSE NIPPLE, GRAY (MNPT) SCHEDULE 80 PVCMODEL SIZE EACH

879005 1/8" $.99

880005 1/4" .99

881005 3/8" 1.09882005 1/2" .95882007 3/4" .99882010 1" 1.29882012 11/4" 1.89882015 11/2" 2.09882020 2" 2.69888005 21/2" 9.39887030 3" 11.19890005 4" 18.29

90º ELL (FNPT X SLIP)MODEL SIZE EACH

407005 1/2" $.35

407007 3/4" .40

407010 1" .75407012 11/4" 1.19407015 11/2" 1.29407020 2" 3.49407030 3" 12.79407040 4" 19.49

PLUMBINGElls/Nipples/Caps

"Close" nipples are those with threads that almost touch

from both sides. They are the shortest possible length.



371371

SP15

90º STREET ELL (MNPT X SLIP)MODEL SIZE EACH

410005-AQ 1/2" $.60

410007-AQ 3/4" .70

410010-AQ 1" 1.19410012-AQ 11/4" 1.59410015-AQ 11/2" 1.69410020-AQ 2" 4.19410101 3/4" x 1/2" .85

UNION (FNPT X FNPT) SCHEDULE 80, WITH O-RINGMODEL SIZE EACH

458005 1/2" $2.59 $2.33/10+

458007 3/4" 2.59 2.33/10+

458010 1" 3.99 3.59/10+458012 11/4" 5.39 4.85/5+458015 11/2" 6.69 6.02/5+458020 2" 10.69 9.62/5+

UNION (SLIP X SLIP) SCHEDULE 80, WITH O-RINGMODEL SIZE EACH

457005 1/2" $2.09 $1.88/10+

457007 3/4" 2.59 2.33/10+

457010 1" 3.99 3.59/10+457012 11/4" 5.39 4.85/5+457015 11/2" 6.69 6.02/5+457020 2" 10.69 9.62/5+

PLUG (MNPT)MODEL SIZE EACH

450005 1/2" $.75

450007 3/4" .80

450010 1" 1.29450012 11/4" 1.29450015 11/2" 1.49450020 2" 1.89450030 3" 3.89450040 4" 8.89

LONG SWEEPTo keep friction losses low, it’s best to use sweeps as opposed to elbows in plumbing systems. These long sweeps are low-pressure rated to 30 psi. PVC compatible with Schedule 40, 160 and DWV size pipes. Female socket on both ends.

MODEL SIZE EACH

SP15 11/2" $4.59

SP20 2" 5.89

SP30 3" 11.29SP40 4" 19.99

PLUMBINGUnions/Plug/Long Sweep/Reducer Bushing

REDUCER BUSHING (SPIG X SPIG) MODEL SIZE EACH

437101 3/4" x 1/2" $ .30

437130 1" x 1/2" .50

437131 1" x 3/4" .50437166 11/4" x 1/2" .70437167 11/4" x 3/4" .70437168 11/4" x 1" .70437209 11/2" x 1/2" .75437210 11/2" x 3/4" .75437211 11/2" x 1" .75437212 11/2" x 11/4" .75437247 2" x 1/2" 1.19437248 2" x 3/4" 1.19437249 2" x 1" 1.19437250 2" x 11/4" 1.19437251 2" x 11/2" 1.19437334 3" x 3/4" 2.89437335 3" x 1" 2.89437336 3" x 11/4" 2.89437337 3" x 11/2" 2.89437338 3" x 2" 2.89437420 4" x 2" 6.39437422 4" x 3" 6.39



MALE ADAPTER (MNPT X SLIP)MODEL SIZE EACH

436005 1/2" $.25

436007 3/4" .30

436010 1" .50436012 11/4" .60436015 11/2" .80436020 2" .99436030 3" 4.49436040 4" 5.69

372

FEMALE ADAPTER (SLIP X FNPT)

FEMALE ADAPTER REDUCING (SLIP X FNPT)

MODEL SIZE EACH

435005 1/2" $.30

435007 3/4" .40

435010 1" .45435012 11/4" .70435015 11/2" .80435020 2" 1.09435030 3" 3.59435040 4" 5.99

COUPLING (SLIP X SLIP) MODEL SIZE EACH

429005 1/2" $.20

429007 3/4" .25

429010 1" .45429012 11/4" .60429015 11/2" .65429020 2" .95429030 3" 3.29429040 4" 4.79429060 6" 15.29

REDUCER COUPLING (SLIP X SLIP) MODEL SIZE EACH

429101 3/4" x 1/2" $.45

429131 1" x 3/4" .80

429168 11/4" x 1" 1.29429212 11/2" x 11/4" 1.39429251 2 x 11/2" 2.19

T.T. BUSHING (MNPT X FNPT)MODEL SIZE EACH

439072 1/2" x 1/4" $1.29

439073 1/2" x 3/8" 1.29

439098 3/4" x 1/4" .80439099 3/4" x 3/8" .80439101 3/4" x 1/2" .80439130 1" x 1/2" 1.09439131 1" x 3/4" 1.09439168 11/4" x 1" 1.69439210 11/2" x 3/4" 1.99439211 11/2" x 1" 1.99439212 11/2" x 11/4" 1.99439251 2" x 11/2" 2.09

COUPLING (FNPT X FNPT)MODEL SIZE EACH

430005 1/2" x 1/2" $.35

430007 3/4" x 3/4" .65

430010 1" x 1" .85

REDUCER BRUSHING (SPIG X FNPT)MODEL SIZE EACH

438071 1/2" x 1/8" $.60

438072 1/2" x 1/4" .60

438101 3/4" x 1/2" .45438130 1" x 1/2" .75438131 1" x 3/4" .75438166 11/4" x 1/2" 1.09438167 11/4" x 3/4" 1.09438168 11/4" x 1" 1.09438209 11/2" x 1/2" 1.29438210 11/2" x 3/4" 1.29438211 11/2" x 1" 1.29438212 11/2" x 11/4" 1.29438247 2" x 1/2" 1.69438248 2" x 3/4" 1.69438249 2" x 1" 1.69438250 2" x 11/4" 1.69438251 2" x 11/2" 1.69438334 3" x 3/4" 2.89438335 3" x 1" 2.89438336 3" x 11/4" 2.89438337 3" x 11/2" 2.89438338 3" x 2" 2.89438420 4" x 2" 6.39438422 4" x 3" 6.39

MALE ADAPTER REDUCING (MNPT X SLIP)MODEL SIZE EACH

436074 1/2" x 3/4" $.50

436102 3/4" x 1" .70

436132 1" x 11/4" 1.59436169 11/4" x 11/2" 1.79436213 11/2" x 2" 2.19

MODEL SIZE EACH

435074 1/2" x 3/4" $.55

435101 3/4" x 1/2" .55

435102 3/4" x 1" .75435131 1" x 3/4" .75

PLUMBINGBushings/Couplings/Adapters



373373

Male With Female ThreadsSIZE MODEL ALUMINUM MODEL POLYPROPYLENE

3/4" Q75AA $7.59 Q75AP $5.191" Q10AA 8.69 Q10AP 5.69

11/4" Q12AA 10.79 Q12AP 5.49

11/2" Q15AA 11.29 Q15AP 5.79

2" Q20AA 12.99 Q20AP 6.69

3" Q30AA 19.79 Q30AP 12.29

4" Q40AA 44.59 Q40AP 17.49

6" Q60AA 88.59 — —

Male With Male Threads SIZE MODEL ALUMINUM MODEL POLYPROPYLENE

3/4" Q75FA $8.99 Q75FP $5.29

1" Q10FA 10.59 Q10FP 5.69

11/4" Q12FA 12.39 Q12FP 5.99

11/2" Q15FA 13.69 Q15FP 6.39

2" Q20FA 14.89 Q20FP 8.29

3" Q30FA 26.69 Q30FP 15.59

4" Q40FA 45.79 — —

6" Q60FA 99.49 — —

Male With Hose NippleSIZE MODEL ALUMINUM MODEL POLYPROPYLENE

3/4” Q75EA $9.69 Q75EP $5.09

1" Q10EA 9.69 Q10EP 5.49

11/4" Q12EA 11.89 Q12EP 5.99

11/2" Q15EA 12.69 Q15EP 6.49

2" Q20EA 14.49 Q20EP 7.49

3" Q30EA 23.59 Q30EP 13.39

4" Q40EA 45.19 Q40EP 19.59

Male PlugSIZE MODEL ALUMINUM MODEL POLYPROPYLENE

1" Q10WA $9.99 Q10WP $4.99

11/4" Q12WA 11.29 Q12WP 5.29

11/2" Q15WA 11.89 Q15WP 5.69

2" Q20WA 12.39 Q20WP 6.89

3" Q30WA 16.99 Q30WP 10.89

3/4” — — Q75WP 3.39

Female CapSIZE MODEL ALUMINUM MODEL POLYPROPYLENE

1” Q10VA $16.29 Q10VP $10.2911/4” Q12VA 18.89 Q12VP 10.3911/2” Q15VA 19.59 Q15VP 12.492” Q20VA 20.09 Q20VP 14.293” Q30VA 25.89 Q30VP 22.194” Q40VA 34.69 Q40VP 29.59

6” Q60VA 92.39 — —

Female With Male ThreadsSIZE MODEL ALUMINUM MODEL POLYPROPYLENE

3/4” Q75BA $16.49 Q75BP $9.69

1" Q10BA 17.79 Q10BP 10.89

11/4" Q12BA 20.79 Q12BP 12.29

11/2" Q15BA 19.79 Q15BP 12.89

2" Q20BA 23.39 Q20BP 14.89

3" Q30BA 37.19 Q30BP 24.99

4" Q40BA 57.39 — —

Female With Hose NippleSIZE MODEL ALUMINUM MODEL POLYPROPYLENE

3/4” Q75CA $15.49 Q75CP $9.39

1" Q10C A 15.89 Q10CP 10.59

11/4" Q12C A 21.09 Q12CP 13.29

11/2" Q15C A 21.09 Q15CP 12.79

2" Q20CA 23.29 Q20CP 14.89

3" Q30CA 34.19 Q30CP 25.19

4" Q40CA 51.29 Q40CP 28.69

6" Q60CA 119.99 — —

Female With Female ThreadsSIZE MODEL ALUMINUM MODEL POLYPROPYLENE

3/4” Q75DA $15.89 Q75DP $9.39

1" Q10DA 16.19 Q10DP 11.49

11/4" Q12DA 19.69 Q12DP 12.29

11/2" Q15DA 20.99 Q15DP 12.59

2" Q20DA 22.59 Q20DP 14.89

3" Q30DA 38.59 Q30DP 25.194" Q40DA 49.49 — —

Replacement GasketsMODEL SIZE EACH MODEL SIZE EACH

Q75G 3/4" $ .85 Q20G 2” $.80

Q10G 1" .75 Q30G 3” .95

Q12G 11/4" .80 Q40G 4” 2.29

Q15G 11/2" .85 Q60G 6” 2.79

PLUMBINGQuick Disconnect Fittings

QUICK DISCONNECT FITTINGSQuick disconnect couplings provide fast, positive, leak-proof connections for air, liquids and dry products. They connect and disconnect in seconds without tools; simply lift the cam levers. The female fittings use a Buna-N gasket where they meet the male fitting for a cushioned, leakproof seal. Choose either the aluminum or black fiber-reinforced polypropylene for most aquaculture applications. The polypropylene is rated to 100 psi on 3/4" to 2" size and 50 psi on the 3" size at 68ºF (20ºC).


374 PLUMBINGANSI Flanges/Bolt Sets/Rubber Sheet

854010

854010G

PLASTIC RUBBER SHEETGood for most general purpose applications. This plastic rubber holds up well to oil, water, abrasion and weather. When used for making gaskets, it conforms to irregular flange joints and seals well under minimum bolt loads. Temp: -20 to 220°F. Tensile strength: 800 psi. Sheet is 36" wide and sold by the foot (buy one foot and get 3 square feet).

MODEL THICKNESS COLOR EACH FOOT

RRB18 1/8" RED $15.09

ANSI FLANGES, VAN STONE STYLEThese ANSI flanges, Van Stone style, utilize two pieces with center socket loose from the flange portion until tightened. Maximum 150 PSI. Gaskets and bolts are not included; see selection below for Gasket & Bolt Sets (sold separately).

854060

Note: Bolts are not stainless steel.

GASKET & BOLT SETSManufactured to ANSI specifications, these gasket & bolt sets are sized to fit the ANSI Flanges, Van Stone style, listed above. Each set includes one flange gasket, set of 4, 8 or 12 bolts, and set of 4, 8 or 12 nuts. Bolts are not stainless steel. These sets are for flange-to-flange connections.

FLANGE SIZE SHIP WT RECOMMENDED MODEL (ANSI DIA.) (LBS) EACH GASKET/BOLT SET

854010 1” 1 $8.99 854010G

854020 2” 2 12.69 854020G

854030 3” 3 21.59 854030G

854040 4” 4 27.29 854040G

854060 6” 5 42.99 854060G

854080 8” 6 69.99 854080G

854100 10” 8 90.59 854100G

854120 12” 10 154.99 854200G

BOLT BOLT NO. OF FITS ANSI SHIP WT MODEL LENGTH DIA. BOLTS/NUTS FLANGE DIA. (LBS) EACH

854010G 2” ½” 4/4 1” 1 $12.29854020G 3” ⅝” 4/4 2” 1 13.89854030G 3” ⅝” 4/4 3” 1 22.79854040G 3” ⅝” 8/8 4” 2 24.19854060G 3½” ¾” 8/8 6” 3 25.69854080G 3½” ¾” 8/8 8” 3 30.49854100G 4” ⅞” 12/12 10” 3 36.79854200G 4” ⅞” 12/12 12” 3 39.89

CONNECT WITH US

/PentairAES /PentairAES /PentairAES /PentairAES/aquatic-eco-systems-inc/AquaticEcoTV


PLUMBINGPipe Cement & Tape/Cutters/Sealants

375

MODEL EACH

SIL1B BLACK, 2.8 OZ $9.79SIL2B BLACK, 10.3 OZ 17.99SIL1C CLEAR, 2.8 OZ 9.99SIL2C CLEAR, 10.3 OZ 18.59

THREAD SEALING TAPEUsed for copper, brass, steel, aluminum, galvanized, PVC and other plastic pipe threads (not recommended for acrylic and plexiglass). Self lubricate joints for easy assembly. Withstands harsh temperatures from -250° to 500°F. PTFE never dries out. Meets Mil Spec T-27730A.

MODEL EACH

371 1/2”X520’ 1.79

O-RING LUBRICANTThis nontoxic, PTFE-based, waterproof lubricant is for wet or dry environments. White, light-bodied, with a temperature range from 0 to 425°F. It prevents rust and is compatible with most metals, rubbers and plastics. USDA H1-rated to be environmentally safe and corrosion free. Coat O-rings, gaskets and bearings before reassembly. 5-oz tube.

PVC JOINT WELDS (APPROX. CEMENT USAGE)ALLOW TWO JOINTS FOR EACH COUPLING, THREE JOINTS FOR EACH TEE, ETC.

1/2” 3/4” 1” 11/4” 11/2” 2” 21/2” 3” 4”Per Pint 130 80 70 50 35 20 17 15 10

SIL2B

Magic Lube® is a registered trademark of Aladdin Equipment Co., Inc.

SILICONE AQUARIUM SEALANTContains no mildew/mold inhibitorsMost silicone sealants on the market should not be used in fish tanks. This one is fish safe for aquarium manufacture and tank repair (after 48-hour cure). Adheres to clean glass, fiberglass, metal, painted surfaces, many plastics and rubbers and nonoily woods. Service range is -60 to 400°F (-51 to 204°C). Meets US Fed. Specs TT-S-001543A, 00230C, Type II. Large size fits standard caulking guns. One-year shelf life.

TECH FAV

PIPE CEMENTPipe cement takes 24 hours to cure.

MODEL EACH

235 FLEX PVC PIPE CEMENT, 1/2 PT $10.49

HAZMAT A

Joint CompoundsWarning: Many general-use pipe joint compounds contain substances that can cause stress cracking in PVC parts. We suggest using PTFE tape (371) on threaded PVC parts. Do not overtighten threaded PVC parts! One or two turns beyond fingertight is generally all that is required to make a sound PVC threaded connection. Unnecessary overtightening may cause damage to both pipe and fitting at some future time.

SIL1B

MODEL EACH 4+

AML $8.29 $7.46

PVC PIPE CUTTERSProfessional PVC pipe cutters are designed for quick, clean cuts of PVC, polyethylene pipe and hose. The hooked jaw holds pipe in cutting position. Blades are made of a special alloy steel. Blades, ratchet and spring have a rust-resistant finish.

KT8A SHIP WT MODEL (LBS) EACH

KT5A PVC PIPE CUTTER TO 11/4” 2 $25.49KT8A PVC PIPE CUTTER TO 2” 12 54.39KTR5A REPLACEMENT BLADE FOR KT5A 1 10.99KT5ASP REPLACEMENT SPRING KIT FOR KT5A 1 1.99KT8ARK REPAIR KIT FOR KT8A 2 16.59


376 PLUMBINGWater Hose/Nozzles

ADJUSTABLE BRASS NOZZLEMade of heavy solid brass, this rugged nozzle is fully adjustable from fine mist to full stream. It features a self-rising stem and is designed to last a lifetime.

JET SPRAY BRASS NOZZLEThis solid-stream, brass jet nozzle is ideal for walkways, sidewalks and driveways.

SALTWATER NOZZLEThis nozzle is specially designed to resist the corrosion caused by salt water. The durable polymer body includes an internal spring mechanism of stainless steel. Leakproof and threaded at both ends.

Gilmour® and Flexogen® are a registered trademark of Fiskars OYJ ABP Public Limited Co.

COMFORT GRIP NOZZLE TECH FAV

• Molded-on vinyl grip is cushioned.• Male hose threaded front for attaching accessories.• Solid brass valve stem with adjusting nut.• Hold-open clip for continuous spraying.• Stainless steel spring.• Heavy-duty, full-size, diecast zinc body.

POLYPROPYLENE DELIVERY NOZZLEWant an easy way to fill up water tanks? This handy delivery nozzle is excellent for delivering fresh or salt water to jugs, tanks and other containers in labs, hatcheries and even aquarium stores. Nozzle body is polypropylene, lever is stainless steel. 1” FNPT inlet.

PREMIUM DUTY WATER HOSEGilmour Flexogen® water hose has a robust double polyester cord reinforcement and highburst-strength construction up to 500 PSI. The Flexogen Advantage construction provides superior flexibility and all-weather performance with a protective collar to resist kinks at the faucet and crush-resistant heavy-duty metal couplings with O-rings for a durable and tight seal. Lifetime Warranty.

SHIP WT MODEL LENGTH DIA. (LBS) EACHH10050 50’ 5/8” 8 $40.89H10075 75’ 5/8” 12 59.59H10100 100’ 5/8” 16 77.29

STAINLESS STEEL WATER NOZZLESHeavy-Duty stainless steel nozzle with rear trigger. Stainless steel coupling and tip for the ultimate in corrosion resistance, impact resistance, durability and quality. Slip-resistant and ergonomic design. Adjustable water flow for improved control. Hold open clip for continuous spray. Pattern nozzle has spray patterns that include clean, soft wash, jet, flower, sweep, garden, rinse, and shrub. Adjustable tip nozzle alters the water stream from jet to wide stream. Lifetime Warranty. SHIP WT MODEL NOZZLE TYPE (LBS) EACH

N400GWR SPRAY PATTERN 0.8 $16.79 N400GCR ADJUSTABLE TIP 0.9 15.69

HOT WATER/HIGH PRESSURE WATER NOZZLEThis industrial spray nozzle is designed to handle the toughest cleaning jobs. With heavy-duty construction and insulating soft-grip over-molds, it is designed for hot water use and/or high pressure levels. Heavy duty die-cast zinc with brass spray tip. Handles up to 200 PSI. Ergonomic curved shape for comfort during use. Adjustable tip alters the water stream.

SHIP WT MODEL NOZZLE TYPE (LBS) EACH

N50500GP ADJUSTABLE TIP 0.6 $8.89

LIFETIME WARRANTYN400GWR N400GCR

LIFETIME WARRANTY

MODEL EACH 4+

NZ23 $3.69 $3.32

MODEL EACH 4+

NZ474 $4.39 $3.95

MODEL EACH 4+

NZ93 $7.89 $7.10

MODEL EACH

NZ35 $59.29

MODEL EACH

NZ22 $8.89


PLUMBINGGarden Hose Accessories

377

GARDEN HOSE MENDER AND COUPLINGSPremium nylon construction for maximum strength and durability. Impact resistant clamp design. Noncorroding, high-grade, stainless steel screws will not strip when tightened. Reusable and leakproof. For garden hose and vinyl tubing with I.D.

GARDEN HOSE ACCESSORIESMODEL EACH 12+

3110-AQ PLASTIC HOSE SHUT-OFF $2.09 $1.883194 PLASTIC HOSE END CAP, 2/PK .70 .633150 PLASTIC "Y" CONNECTOR W/SHUT-OFF 3.59 3.23TVW 76# WASHERS, 100/PK 6.99 —

GARDEN HOSE ADAPTERSThese natural nylon adapters convert garden hose thread (GHT) to standard national pipe thread (NPT) or to barb fittings. NPT is used with most PVC fittings.

MODEL HOSE I.D. EACH

HM22 HOSE MENDER 5/8", 3/4" $2.89HM34 FEMALE COUPLING 5/8", 3/4" 1.79HM35 FEMALE COUPLING 7/16", 1/2", 9/16" 1.79HM46 MALE COUPLING 5/8", 3/4" 1.59HM47 MALE COUPLING 7/16”, 1/2”, 9/16” 1.59

HM34

HM22

HM46

3150

3110-AQ

3194

GH3BGH2A GH4A GH6

NPT

GHT

1/2" NPT 3/4" NPT GHT NPT MODEL EACH 10+ MODEL EACH 10+

MALE MALE GH2A $1.29 $1.16 GH2B $1.29 $1.16FEMALE MALE — — — GH3B 1.49 1.34MALE FEMALE GH4A 1.49 1.34 GH4B 1.49 1.34

MODEL GHT BARB EACH 10+

GH5 MALE 1/4” $1.19 $1.07GH6 MALE 3/8” 1.19 1.07

Learn from our own industry experts Dr. Tom Losordo and Dennis DeLong.• An introduction to recirculating systems• Critical considerations before designing recirculating systems• Component options for use in recirculating production systems• Developing an appropriate design for your aquaculture application• Management principles of recirculating aquaculture systemsPentairAES.com/workshops

RAS TECHNOLOGY WORKSHOP

PLUMBING PRODUCTS - pentairaes.com · Online Orders: PentairAES.com I Phone Orders and Tech Advice: 877.347.4788 PLUMBING Butterfly Valves 349 KEYSTONE COMPOSEAL RESILIENT SEATED

Documents