This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Update Alert: Firmware updates are posted the web on a regular basis. We recommendon
that you check for firmware and/or install guide updates prior to installing this product.
The TL7 firmware for 2 is an all-in-one door lock and override module compatible with specificDBALLScion and Toyota vehicles.
This module can only be flashed and configured using Xpress at www.directechs.com orVIPusing the Directechs Mobile application for smartphones. Refer to the Module Programmingsection on page 22 for more information.
The following table lists the vehicles and features which are compatible with this product. The number assigned to each yearallows you to determine which installation type should be used for your vehicle.
Key Type G-stamped keys Standard KeyFor vehicles with key , seedot-stamped s the
1TL firmware.Some Toyota 2010+ models havedifferent encryption types. Pleaselook at your key blade and identifythe markings. A “G” means thevehicle is compatible with the 7TLfirmware.
H-stamped keys
H
It is important to make sure you do connect the keysense wire in the installation for each of these vehicles orNOTyou will encounter issues when attempting to start the vehicle.
For vehicles with key , seedot-stamped s the10TL firmware.
It is important to make sure you do connect the keysense wire in th installation or youNOT iswill encounter issues when attempting to start the vehicle.
Make this connectiononly if the vehicle isequipped with AutomaticHeadlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
Body ECU ConnectorNote: RDA wire is NOTrequired in all vehicles.
Refer to vehicle Wiring andConnector ReferencesInformation for wire and
connector details.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
1
CUT
Installation Type 1Page 3
P#: XKD2D65TX
(-) Ground
RX
(+)12V
10
DBALL/DBALL2
RF
Prog utton. B
LED
4
14
12
2
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Make thisconnection if theonlyvehicle is equippedwithAutomatic Headlamps.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
1
It is important to make sure you do connect the keysense wire in th installation or youNOT iswill encounter issues when attempting to start the vehicle.
[3] in 18(-) Parking Lights: P(-) putTrunk In
3 Trunk: (-) InputRed/White:
Installation Type 2Page 6
10
RF
Prog utton. B
LED
4
14
12
2
P#: XKD2D65TX
(-) Ground
RX
(+)12V
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Make this connectiononly if the vehicle isequipped with AutomaticHeadlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
SIL Interr. (conn. side) : 8Yellow:
SIL Interr. (veh. side) : 9Orange/Yellow:
(-) :Power LiftgateRed, pin 6
SIL: , p 0in 1Blue
8 46 27 35 1
Power LiftgateWhiteSwitch
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
CUT
CUT
It is important to make sure you do connect the keysense wire in thNOT isinstallation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
1
Installation Type 3Page 8
P#: XKD2D65TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
It is important to make sure you do connect the keysense wire in thNOT isinstallation or you will encounter issues when attempting to start the vehicle.
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output2
(+) Starter Output1
Not required in D2D mode.
(-) OutputLock 4[ ]
(-) OutputUnlock [ ]4
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
[ ]2 (-) Hood Status Output: 12Blue/Red:
(-) Door Status Input
(-) E-Brake Status Input
[ ]2 (-) Hood Status Input
(+) Brake InputStatus
5
10
4
9
2
7
1
6
3
8
[ ]4 (-) Lock/Arm:, pinViolet 4
[ ]4 (-) Unlock/Disarm:Green/Black, p 8in
Harness from Driver Side( )Gray or White Connector
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
Installation Type 4Page 10
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
[4] Remote starter MUST be programmed during flashing to unlock before start and lock after start. This can be done when flashing the firmware underthe Data Feature Configuration section and enabling Safelock under Smart OEM Alarm Control. This Unlock output must also be programmed for doublepulse.
It is important to make sure you do connect the keysense wire in th installation or youNOT iswill encounter issues when attempting to start the vehicle.
1 8
169
Diagnosticconnector OBDII
Rem
ote
Sta
rter
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) GWR (Status) InputBlue/White:
9: (+) Ignition InputPink:
[ ]1 (AC) Tach Output: 5Violet/White:
(+) Brake Output: 6Status Gray:
(-) E-Brake Status Output: 1Black/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
SIL: 10Yellow/Black:
[ ]2 (-) Hood Status Output: 12Blue/Red:
HS CAN : , pHigh in 6Violet
SIL in 7: , pBlue
HS CAN : , pLow in 14White
(+) 12V (+) 12V : 13Input Red:
(-) Ground (-) Ground: 14Black:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
[3] Output(-) Parking Lights
[1] (AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[2] (-) Hood Status Input
(+) Brake InputStatus
(-) Ground
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(-) GWR Output
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
Ignition onnectorC
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
[3] in 13(-) Parking Lights: , pWhite
4 3 2 1
13 12 11 10 9 8 7 6 5
Headlight Switch
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
P#: XKD2D65TX
(-) Ground
RX
(+)12V
10
DBALL/DBALL2
RF
Prog utton. B
LED
4
14
12
2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
Make this connectiononly if the vehicle isequipped with AutomaticHeadlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
Power LiftgateWhiteSwitch
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
CUT
It is important to make sure you do connect the keysense wire in thNOT isinstallation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
5 34 2 1
(-) Power Liftgate:Red, pin 4
Ignition onnectorC
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
(+) Starter Output2
Installation Type 6
P#: XKD2D65TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Page 14
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
Make this connectiononly if the vehicle isequipped with AutomaticHeadlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
Ignition onnectorC
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
CUT
It is important to make sure you do connect the keysense wire in thNOT isinstallation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
RDA: 11Orange/Black:
RDA: ,Pinkpin 26
Body ECU Connector(middle plug)
456
161718
282930
131415
252627
101112
222324
123
789
192021
Tire PressureWarning ECU
(Behind glove box)
6 5 4 3 2 1
121110 9 8 7
SIL Interr. (conn. side) : 8Yellow:
SIL Interr. (veh. side) : 9Orange/Yellow:
SIL: , p 0in 1White
CUT
3: (-) Trunk InputRed/White:
(-) Trunk Output
18
Installation Type 7
P#: XKD2D65TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Make this connectiononly if the vehicle isequipped with AutomaticHeadlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output2
(+) Starter Output1
Ignition onnectorC
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
CUT
It is important to make sure you do connect the keysense wire in thNOT isinstallation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
RDA: 11Orange/Black:
RDA: ,Bluepin 61
Body ECU Connector(middle plug)
456
161718
282930
131415
252627
101112
222324
123
789
192021
3: (-) Trunk InputRed/White:
(-) Trunk Output
Installation Type 8
P#: XKD2D65TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Make this connectiononly if the vehicle isequipped with AutomaticHeadlamps.
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
SIL Interr. (conn. side) : 8Yellow:
SIL Interr. (veh. side) : 9Orange/Yellow:
SIL: , p 0in 1Blue
(+) 12V Input
(+) Ignition Output2
(+) Ignition Input/Output1
(+) Starter Output1
CUT
CUT
It is important to make sure you do connect the keysense wire in thNOT isinstallation or you will encounter issues when attempting to start the vehicle.
20 19
Not required in D2D mode.
Ignition onnectorC
Fuse Box Connector
Refer to the Vehicle WiringReference Information for wire
and connector details.
4 3 2 1
8 7 6 5
1
Installation Type 9Page 20
P#: XKD2D65TX
(-) Ground
RX
(+)12V
10
RF
Prog utton.B
LED
4
14
12
2
DBALL2
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII s
[ ]1 Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Tach is not detected in all vehicles;refer to the Vehicle Application Guide for compatibility.
[ ]2 If equippedfactory . If not, a hood switch must be installed and connected to the remote starter.
[ ]3 Parking light output only required if Parking Lights are not supported in data.
[4] Autolights Interrupt only required if vehicles are equipped with Autolights.
Refer to the LED Diagnostics section on page for more information and for troubleshooting purposes.s 24-25
The master key module programming .is to complete the successfullyREQUIRED
3
2Insert turnand the key to the ignition position. The turns solidLED ONgreen for 3 seconds. This may take up to .5 seconds
Turn the thekey to position.OFF
&Key IN O
FF
START
IGN
Page 22
Key OUT OF
F
START
IGN
1Solid
Wait until the LED turns solid red.ON
Note: To skip the transponder programming and use convenience features only,press the 5 times.programming button
You have successfully completed the module programming sequence.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
When the flashing operation is successful, you can proceed with the programming instructions below.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.
D2D Installation
W W Installation2
If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.
10-pinD2D
1st
12-pin14-pin
2nd
3rd
10-pinD2D
1st
4th
12-pin14-pin
2nd
3rd
Flashing a module using your computer:
1. Connect the interface module to your computer using theXKLoader2.
2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module
3. Follow the instructions to select your vehicle, installationtype, and configure your options.
4. Once you have configured the firmware options, click on theFLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone ortablet.
3. Select and follow the on screenFLASH YOUR MODULEinstructions.
Green3 seconds
Note: If the transponder programming was skipped, the turnsLED ONsolid orange for 3 seconds then shuts when programming is done.OFF
Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.
Release the programming button. The turns solid red.LED ON
Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List
1 OR
If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button
D2D Installation
If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
1st
12-pin14-pin
2nd
4th
3rd
10-pinD2D
1st
5th
12-pin14-pin
2nd
3rd
4th
Hard Reset
2 & &Solid SolidRelease
Wait 3 seconds until the orange then release theLED turns solidONp The then turns solid red.rogramming button. LED ON
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.
1 OR
If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button
D2D Installation
If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.
It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possibleusing the information on this page.
Feat. Operation Flashes/Option Description
1. Disabled* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver Priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
2. All Unlocks all doors on first press.
1. Trunk Trunk: Will pop the trunk if available.
2. Right Sliding Door* When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Trunk: Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door* When available, will operate the left sliding door.
1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be
executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at
the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the
vehicle in the remote start sequence, only when required. The reason for this is, factory alarm control
must often be done by lock or unlock operation. This could create unnecessary actions on door lock
modules, such as the horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and
door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped
with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the
remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the
Safelock feature is active, will work perfectly with this option and will make it invisible to the user.
1. Not Equipped* The vehicle is not equipped with an automatc trunk/hatch opening system.
2. Equipped The vehicle is equipped with an automatc trunk/hatch opening system.
To enter feature programming routine- Turn t , thenhe ignition .ON OFF- Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )
Programming button.- The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red
the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willuntil .a new command is entered
Changing feature options- Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/- The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred
the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature.- The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED
indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered
When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON
sequence.OR
- Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.
For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.